D2061ADSL TESTER
D2061ADSL TESTER
OVER POTS – OVER ISDN
Smart troubleshooting tool
Powerful background monitor
Multi layer tester
ADSL, ATM and IP layers test
Ideal companion for installers
Light weigth, small footprint, robust,
OVERVIEW
FEATURES AT A GLANCE
The D2061 has been specifically realized for ADSL lines and turns out to be
Specific ATM layer tests
Complete IP layer feature including PPP
one of the smallest, lightest and easy to handle devices on the market.
Thanks to the ‘Universal Modem’ feature, this tester is able to simulate the
user’s modem and host checking each critical point of an ADSL connection
and file transfer simulation
and obtaining a complete set of parameters such as line bit rate and
occupation capacity, but also connection bit rate both Fast and
Predefined test set-ups to save time on site
Possibility to save test results for later analysis
Multi protocol monitor and analysis including frames
Interleaved, noise margin and bit per tone allocation.
As with all the measurement devices made by Aethra®, it offers helpful
features for the technician in installation, maintenance and troubleshooting
phases.
The graphic interface, common to the new generation test equipment
decoding
family made by Aethra®, satisfies all the user’s needs. Navigating through
the various menus is both easy and immediate thanks to the bright,
back-lit, high resolution display as well as the zoom feature.
Includes PC108 for WindowsTM software for
powerful analysis and remote management
The features PREDEFINED TESTS and HISTORY, are used to manage and
store personalized test setup and to recall the results of each test
performed. These, together with the possibility to setup a personal most
Different ordering codes for ADSL over POTS and
ADSL over ISDN
used tests list, make a technicians daily tasks simpler by avoiding possible setup errors or subsequent analysis of the results obtained.
The Smart Status™ feature allows the modem, the line and the device
status to be displayed immediately. In particular, is shown the number of
bits per tone assigned both in graphical and tabular format, the error
count, events and anomalies on the line, the current and historical
alarm status and evolved statistics about the ATM level are displayed.
Thanks to Smart Status™ the user has all the necessary information
at a push of a button.
In field upgradable
firmware
BACKGROUND MONITOR
BER
The device captures and decodes all
modem events. During the active phase of
the connection, all the AAL-5 packets are
also captured.
Moreover, it is possible to capture and
decode communication protocol events
over ISDN D channel1.
In POTS mode, the D2061 is able to perform high impedence monitoring of POTS2
events.
Advanced analysis through the PC software3
issued with the device, helps to solve
also more complex ADSL connections
problems.
• Physical layer monitoring with alarms
and error checks
• Line events analysis
• AAL-5 encapsulation decoding
• D1 channel and POTS2 line monitoring
• Real time and off-line decoding
• Capturing filters
• G.826/M.2100 statistics information
CONNECTION
Using this test, it is possible to control all
ADSL connection data both for Upstream
and Downstream sides.
The costumer’s contractual parameters
verification is immediate and easily
interpretable.
•
•
•
•
•
•
ATM Fast/Interleaved bit rate
ATM maximum line rate
Relative capacity
Noise margin
Attenuation
Output power
Through an appropriate option1 D2061 can
perform specific tests over S/T-Bus for line
quality verification (BERT) and for ISDN
basic access general control.
•
•
•
•
G.821
Different test pattern
Test modes End-to-End and Selfcall
Errors injection
AUTOMATIC TESTS
ATM 5
Using of this test, it is possible to verify if
the ATM layer is working correctly up to the
ATM termination unit.
This test allows OAM as well as AAL-5 cells
generation to be performed with response
times (ms), errors and statistics5.
• OAM cells generation, F4 and F5
type
• AAL-5 packets generation test
• Loop-back OAM cells management
• Programmable number of Ping
requests
• Errors and statistics
• Waiting response time (sec.)
This test is used to verify immediately and
automatically the ISDN line under measurement.
If not otherwise specified, the device automatically generates a series of calls toward
a remote user or in autocall mode and verifies the complete status of the line.
With the possibility to set up and save a
personalized test sequence, the control of
several line typologies is easier and more
immediate.
• ST2061option
• Physical layer settings control
• Layer 2 configuration
• Availability status of the several bearer
services, teleservices and supplemen
tary services
• Availability check of single B channels
IP 6
Thanks to IP PING test, the D2061, checks
the connection to the Internet Provider, the
reachability of a remote host and the
relative response times6.
Moreover, all the information from the
server such as messages and local,
remote and server IP addresses is
provided. This allows the correct connection
settings of the user to be checked.
The test IP GENERATE TRAFFIC, allows a
data transfer between hosts to be
simulated. This test, more exhaustive than
IP PING, is able to measure the throughput
of the connection in progress.
• IP Bridge, IP Router, PPPoE, PPPoA,
Protocols
• PPP, IP, UDP, DHCP, DNS, ICMP, TFTP support
• PAP and CHAP (MD5) authentication
• Static and Dynamic IP address
• Gateway management and address
• Settable packet length and testing file
• IP statistics and response times
• Throughput calculation
• IP address book, password and
User ID for immediate Internet login
MISCELLANEOUS
Thanks to the integrated microphone and
loudspeaker the D2061 is able to simulate
both analogue POTS2 and ISDN1 telephones.
For the version over POTS, an external
splitter4 is also available, to substitute the
user’s one. The D2061 does not require an
external splitter to work.
•
•
•
•
ISDN terminal simulation
Loopbox
Evolved POTS terminal simulation
CLI displaying
ST2061
AB2001N
3
Pc108forWindows™
4
MF206x
5
ATM2061
6
IP2061
1
2
TECHNICAL SPECIFICATIONS
TELECOM INTERFACES
SMART STATUS™
• ADSL access
ATU-R
• Physical layer
ITU-T (CCITT) Rec. ITU-T-I.361,
ITU-T- I.363.5, ITU-T- I.432,
ITU-T- I.610, ITU-T-I.731
• ISDN Basic Rate [ST2061]
S/T
• ADSL line
• ATM layer
ITU-T (CCITT) Rec.I.430,
ETS 300 012
ADSL LAYER
• D2061 over POTS1
Full Rate
G.DMT
G.Lite
Multimode
• D2061-I over ISDN2
G.DMT
Others
Alcatel
• Handshake
• ISDN line
ANSI T1.413 issue 2
G.992.1,Annex A (ADSL over POTS)
G.992.2
ADSL MONITOR ANALYSIS
• Stand alone decoding
G.992.1,Annex B (ADSL over ISDN)
ADSL over POTS/ISDN
U-R2 (T-DSL)
ADSL over ISDN ETSI DTS/TM
G.994.1 (ex G.Hs)
1-2
Only one module at time is
available from the factory
G.826 / M.2100
ES, SES, BBER,UAS DMT bits per
tone, graphical and table
format, alarms and errors
Tx/Rx cells counters,
AIS-RDI-LB OAM cells
counters, unmapped cells
counter, VCs (VCI/VPI) of
unmapped cells [ATM2061]
Status levels ISDN 1, 2 and
3 clearly displayed [ST2061]
• ADSL events decoding
ADSL and AAL-5
Graphical and tabular format
• ATM header decoding
• AAL-5 decoding
Hexadecimal decoding
grouped by levels
LLC, Discovery PPPoE,
Discovery ARP and MAC
Address Payload, Trailer
CONNECTION
ATM LAYER [ATM2061 OPTION]
• ADSL line mode
• Stack
• ADSL maximum bit rate Kbps (DW/UP)
OAM Implementation
ATM Adaptation Layer
VC channel selection
• Multiplexing methods
F4 and F5 OAM loopback cells
OAM ITU-T I.610
AAL-5
Settable by the User
LLC/SNAP or VC Multiplexed
IP/PPP LAYER [IP2061 OPTION]
• Stack
Data encapsulation methods
RFC number
• PPP
• Operative ATM speed rate
Fast mode Kbps (DW/UP)
Interleaved mode Kbps (DW/UP)
• Relative Capacity % (DW/UP)
• Noise Margin dB (DW/UP)
• Attenuation dB (DW/UP)
• Output Power dBm (DW/UP)
• ATU-C manufacturer & version
ANSI mode
IP over ATM Bridged, IP over
ATM Routed, PPP over ATM,
PPP over Ethernet
RFC2684 (ex 1483), 2225,
2364, 2516
• Number of bits per tone, frequency and bit per tone value
Client, Server
• Display
BIT PER TONE
• Cursors
• Results format
AVAILABLE OPERATING MODES
ATM [ATM2061 OPTION]
• ADSL
ATU-R
ATU-R + Host
• ISDN
TE-S (BRI)
• POTS
TE
MON
• VCI / VPI
• Type of cell
ST2061 option
AB2001N option
AB2001N option
BACKGROUND MONITOR
• Events
Moved along the graphic,
provides information for each tone
128, 256 tones
Table, Graphic
ADSL parameters, alarms,
errors, AAL-5 packets
• ISDN D channel monitor [ST2061option]
• POTS line Monitor [AB2001 option]
• Programmable filters
Independent filters capture
and displaying
• Analysis of results stored into PC
PC108 for Windows™
• Location ID (end-to-end)
Statistics and Errors
F4 end-to-end, F4 segment,
F5 end-to-end, F5 segment
User defined
• ATM OAM cell Management
• Type of Test
ATM PING, OAM & AAL-5
packets test, traffic generator
ENVIRONMENTAL CHARACTERISTICS
IP [IP2061 OPTION]
• IP address supported
• Authentication protocol PPP
• Gateway selection
• LLC/SNAP encapsulation
• Type of Test
Static, Dynamic (DHCP)
PAP, CHAP (MD5)
IP Bridged mode
User defined
IP Ping (ICMP), IP generate
traffic (TFTP)
LOOP-BOX FEATURE [ST2061 OPTION]
AUTOMATIC ACCESS TEST [ST2061 OPTION]
• Fully automated Access test
• Automatic supplementary services test
• Programmable test sequence
• Pseudo-Random bit sequence
• Error Injection
• EMC Aspects
ES, SES, US, DM, PASS/FAIL
User definable 211-1, 215-1,
223-1, 16 bits octet
User menu selectable: Manual,
Single, Automatic
HISTORY AND PREDEFINED TESTS FEATURES
• Saving and recalling of 10 different setup and results for each
kind of tes
• AUX
• RS232
• Handset
• Power in
• CE Marking
≈ 500 gr.
100 (w) x 180 (l) x 50 (d)
Rechargeable, Ni-MH
≈ 3 hrs @ 25°C, LCD back-lit off
115/230Vac ±10% @ 50/60Hz
-40oC to +70 oC
-5oC to +45 oC
-10oC to +55 oC
≤ 93% RH @ 40 oC
≤ 70% RH @ 55 oC
EN 61010-1, EN 60950, EN 41003
EN 55022, EN 55024,
EN 61000-3-2 / -3-3
Class B (residential devices)
MISCELLANEOUS
• LCD display
320x200 Graphic display wide
bright and back-lit, with
Zoom function
• Internal microphone & loudspeaker
• Upgradable firmware
• MF206x, POTS Microfilter
CONNECTORS
• ADSL line interface
Weight, with battery
Dimensions, with holster (mm)
• Power
Battery Type
Battery life
External AC/DC adapter
• Temperature
Storage/Transport
Operating, nominal
Operating, limits
• Humidity, non-condensing
• User's Safety Aspects
BIT ERROR RATE TEST [ST2061 OPTION]
• G.821 statistics
• Dimension
By RS232 port
Option
OPTIONS
2 wires RJ11
DB15-HD
Mini - DIN 4 (ISO 4902)
4 wires RJ9. Balanced
External AC/DC adapter 4 wires
Aethra SpA
Telecommunications
via Matteo Ricci 10
60020 Ancona - Italy
Telephone +39.071.218981
Fax
+39.071.887077
Video 1
+39.071.2189160
Video 2
+39.071.2189701
Email: info.aethra@aethra.com
www.aethra.com
• ATM2061
• IP2061
• ST2061
• AB2001N
ATM Stack and Statistics
IP Suite Test
ISDN BRI-S/T terminal similutor
POTS Terminal Simulator
and Monitor
Aethra, Inc.
701 Brickell Avenue
Suite 1390
Miami, FL 33131 USA
Telephone
+1.305.375.0010
Toll Free (US only) 1.888.4.AETHRA
Fax
+1.305.375.0655
Video
+1.305.577.3524
Email: info.na@aethra.com
Aethra, the Aethra logo and D2061 are trademarks, registered trademarks, or service marks of Aethra SpA Telecommunications in Italy, the United States, and/or other countries. All other company and product names
may be registered trademarks or trademarks of their respective owners. Information furnished by Aethra SpA Telecommunications and Aethra, Inc. in this datasheet is believed to be accurate. Products sold and licensed
by Aethra SpA Telecommunications and Aethra, Inc. are covered by warranty and patent indemnification provisions appearing in its purchase and license agreements. Aethra SpA Telecommunications and Aethra, Inc.
reserve the right to discontinue production and change specifications and prices at any time without notice. Copyright ©2003 Aethra SpA Telecommunications - All rights reserved. Additional regional offices are located
on our website: www.aethrausa.com. For further details about technical specifications please see “Products” on www.aethra.com
Code 071062009GB Rev.0 (06/03)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising