Manual: Advantage DK (ADV-1000)

Manual: Advantage DK (ADV-1000)
Installation and
Operating Manual
Advantage DK
ADV-1000
ADV-1000i (intercom)
Digital Access Control Station
“Your Partner in Access Control”
www.americanaccess.com
Contents
Two-Year Limited Warranty
PARTS CHECKLIST
INTRODUCTION
INSTALLATION
HARNESS COLOR CODES
WIRING CONNECTIONS
THE IDLE MODE
ACCESS CODES AND FUNCTION CODES
GOOD TONES and ERROR TONES
PROGRAMMING THE DK UNIT
Program Relay “A” Access Codes - Sub-Mode 1
Delete Individual Access Codes - Sub-Mode 2
Change the Master Code - Sub-Mode 3
Set Sleep Code -- Sub-Mode 4
Set Latch Code -- Sub-Mode 5
Set Relay Output Times -- Sub-Mode 6
Program Relay “B” Access Codes -- Sub-Mode 7
Enable or Disable the “Three Strikes … You’re Out” feature -- Sub-Mode 8
Event Input -- Sub-Mode 9
Erase All Codes -- Sub-Mode 0
RESETTING THE DK UNIT
Master Reset
Unit Reset
Troubleshooting
Customer Service and Tech Support
Notes
Page 2 American Access Systems / Security Brands, Inc.
3
4
5
5
7
7
8
8
9
9
10
10
11
11
11
11
11
12
12
13
13
13
13
14
15
16
Two-Year Limited Warranty
This Warranty applies to:
American Access Systems “Advantage DK” access controls
What is Covered:
Any defects in materials or workmanship
Coverage Period:
Two years from date of purchase
What We Will Do:
If your American Access System (AAS) product is defective and returned within two years of purchase, well will
repair, or at our option, replace the unit at no charge to you. If we repair your AAS Product, we may use new or
reconditioned parts. If we choose to replace your AAS product, we may replace it with a new or reconditioned unit
of the same or similar design. The repair or replacement unit is warranted for (a) Ninety days (b) the remainder of the
original two-year warranty period, whichever is longer.
Limitations:
Implied warranties, including those of fitness for a particular purpose and merchant ability(an unwritten warranty that
the product is fit for ordinary use,) are limited to two years fromthe date of purchase. AAS will not pay for loss of time,
inconvenience, loss of use of your AAS product, service calls, or property damage caused by your AAS product or its
failure to operate, or any other incidental or consequential damages. Some States do not allow limitations on how
long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
exclusions or limitations may not apply to you.
What We Ask You To Do:
To receive warranty service for your AAS product, you must provide proof of the date of purchase. Contact the
original dealer or installer of the product and return your AAS product along with the receipt to them. If you have
problems locating the dealer or installer, contact American Access Systems at (303) 799-9757, and we will direct you
to an AAS authorized dealer or distributor. If you ship your AAS product, you must prepay all shipping charges. We
suggest that you retain your original packing material in the event you need to ship your AAS product. Upon return,
include your name, address, phone number, proof of date of purchase, and a brief description of the operating
system problem. This information needs to be included to receive an AAS “RMA” number.
What This Warranty Does Not Cover:
The warranty does not cover defects resulting from accidents, damage while in transit, alterations, unauthorized
repair, failure to follow installation and operating instructions, misuse, fire, flood, or acts of God. Nor do we warrant
your AAS product to be compatiblwith any particular external device or peripheral. If your Warranty has expired on
your AAS product, or if your product is NOT covered, contact your dealer or installer for advice on whether we will
repair your AAS product and other repair information, including estimated repair costs and additional charges that
may be incurred. We, at our option, may replace, rather than repair your AAS product with a new or similar design if
the damage to the unit is severe or extensive. This is the only Warranty we offer on this product, and it sets forth all of
our responsibilities regarding your AAS product. There are no other express Warranties.
State Law Rights:
This Warranty gives you specific legal rights, and you may also have other rights which varyfrom State to State.
Page 3 American Access Systems / Security Brands, Inc.
Parts Checklist
Parts that are included in the box include the following items. If any of the items is missing, contact American Access
Systems (AAS)
QTY
1
Item
Advantage DK Control Station (w/2 keys)
4
¼”-20 X ½” carriage bolts
4
¼”-20 hex nuts
Tools Needed For Basic Installation
••
••
••
••
••
Wire nuts or appropriate terminals/connectors
Wire strippers
Wire cutters
3/8” drive ratchet, 6” extension, 7/16” socket
Digital or Analog multi-meter
Technical/Customer Support
1-303-799-9757 or
techsupport@securitybrandsinc.com
SECURITY BRANDS INC
1675 West Yale Ave.
Englewood, CO 80110
phone: 303-799-9757
fax: 303-799-9756
sales@securitybrandsinc.com
www.securitybrandsinc.com
Page 4 American Access Systems / Security Brands, Inc.
Introduction
The American Access Systems (AAS) Advantage DK unit is a high-quality, user-programmable, commercial-duty
digital key control station designed to control access to a passageway using 4-digit access codes. The Advantage
DK integrates state-of-the-art electronics resulting in a product which is highly sophisticated, yet inexpensive. The
Advantage DK unit features: • 1 programmable 4-digit Master Code. (Factory default is 1 2 5 1 … it is recommended
that you
re-program to a personal master code of your choice.)• 1 programmable 4-digit Sleep Code • 1
programmable 4-digit Latch Code • Master user ability to program up to 1000, 4-digit access codes which can
be assigned to 1 of 2 relays• A programmable “Three Strikes You’re Out” feature which disables the unit for
approximately 90 seconds if three incorrect Access Codes are entered during a 90-second time period• Two relays
programmable from ½ to 999 seconds incorporating both normally open (N/O) and normally closed (N/C) contacts.•
An external event trigger, programmable as a Remote Inactive, Arming, or Remote Open input.
Before Installation
To take full advantage of the 24 month limited warranty, you must register with American Access Systems, Inc. Please
read and review the Warranty (page 3), complete the enclosed Warranty Registration card and send it to:
Security Brands, Inc.
Warranty Registration
1675 West Yale Ave.
Englewood, CO 80110
Installation
MOUNTING THE UNIT
The tools and instruments needed to install your unit and a Parts Checklist are shown on page 4. Make sure you have
all the tools listed before you begin. It’s a good idea to make sure to check off the items enclosed with the unit. If any
parts are missing from the package, contact American Access Systems immediately.
Mounting the unit to an AAS gooseneck pedestal (18-001) or double height gooseneck (18-003)
Locate the four carriage bolts and four hex nuts found inside the shipping box. With the keypad face open, place
the unit against the pedestal flange, insert the four carriage boltsfrom the back of the unit and tighten the hex nuts
from the inside. Wrench tighten the hex nuts securely. Do not over tighten.
SYSTEM CONNECTIONS
An Operator Wiring Diagram and a Door Strike/Mag Lock wiring diagram for the Advantage DK are shown on page
5. • The most common installation connects the DK unit to a Gate Operator only. Refer to the Operator Wiring
Diagram (the top drawing.) • If the DK unit is being connected to other devices and equipment, such as a door strike
or mag lock, use the Door Strike/Mag Lock Wiring Diagram (the lower drawing.)
Page 5 American Access Systems / Security Brands, Inc.
Standard Hook-up Diagram for Advantage ADV-1000
Page 6 American Access Systems / Security Brands, Inc.
BOARD LAYOUT
_______________________________________________
_______________________________________________
_______________________________________________
Page 7 American Access Systems / Security Brands, Inc.
• Carefully study the diagram that best suits the installation conditions. The following is a key to the wire harness color
codes.
HARNESS COLOR CODES
WHITE (AC Hot) (DC +)
11.5 - 29 volts AC or DC
WHITE (AC Neutral)(DC -)
11.5 - 29 volts AC or DC
GREEN
EARTH GROUND ONLY
RELAY A (PRIMARY) CONTROL COLOR CODES
BROWN
11.5 - 29 vRELAY (A) COMMON
ORANGE
RELAY (A) NORMALLY OPEN (N/O)
BLUE
RELAY (A) NORMALLY CLOSED (N/C)
RELAY B (SECONDARY) CONTROL COLOR CODES
(Use if controlling a second device)
GRAY
RELAY (B) COMMON
VIOLET
RELAY (B) NORMALLY OPEN (N/O)
YELLOW
RELAY (B) NORMALLY CLOSED (N/C)
WIRING CONNECTIONS
1. The DK unit is designed to operate between 11.5 volts minimum and 29 volts AC maximum. Using a multi-meter,
measure the supply line voltage to make sure it falls within these tolerances.
2. IMPORTANT: TURN OFF THE POWER SUPPLY BEFORE MAKING ELECTRICAL CONNECTIONS
3. Locate the two white wires on the circuit board main harness and, WITH THE POWER OFF, connect them to the
power supply leads. Use wire nuts or connectors to secure the connections. The DK unit is rectified. Polarity
need not be observed.
4. Connect the primary device to be controlled to the unit’s primary relay control leads.
a. If you are connecting to a gate operator or electric door strike, use the BROWN and ORANGE leads for
normally open contact. (Refer to the Wiring Diagrams, page 5.)
a. If you are connecting to a mag-lock or any device that requires power in the locked state, use the BROWN
and BLUE leads for normally closed contact. (Refer to the Wiring Diagrams, page 5.)
a. If you interface with a secondary device, connect the unit’s secondary relay control leads to the secondary
device. (Refer to the Wiring Diagrams, page 5.)
2. 4.Connect the Green lead to Earth Ground.
3. 5.Before supplying power to the unit, refer to the appropriate wirin
diagram to double- check all connections. When you are sure you have the unit wired correctly, apply power
to the unit.
a. If this is the FIRST TIME POWER UP, the unit will perform a self-diagnostics routine. After each test has passed,
the unit will respond with a tone. The unit will perform a total of 4 tests (depending upon the equipment
connected to the unit.) The unit will then flash the LED’s several times while it is performing a memory setup. a.
Once all the tests have passed and the unit is set up correctly, you will hear a “GOOD TONE” (an oscillating
high tone) from the unit. If the unit does not perform as above, quickly shut off power to the unit and contact
your distributor or American Access Systems.
NOTE: The unit will perform a self-diagnostics routine only during firsttime power up. After first-time
power up, the unit will sound a “GOODTONE” (an oscillating high tone) each time power is applied.
Page 8 American Access Systems / Security Brands, Inc.
THE IDLE MODE
When the desired connections are complete and power is supplied to the unit, the unit will be in the IDLE MODE. The
IDLE MODE is the normal mode of operation, meaning the unit is ready to accept input from the keypad. When in
the IDLE MODE, you have approximately 4 seconds between key presses. If this time is exceeded, you will receive an
ERROR TONE. Any time you hear an ERROR TONE, simply begin whatever operation you were attempting over again.
ACCESS CODES AND FUNCTION CODES
There are two types of codes you need to keep in mind when using the Advantage DK unit.• Access Codes, quite
simply, are the numbers that are programmed into the unit and assigned to the users who need to access the gate
or door. The Access Codes are the “everyday” use codes. Up to 1000 Access Codes can be programmed into the
unit. • Function Codes, on the other hand, are special modes that only the Master User or Administrator can enter to
control how the DK unit is programmed and operates. There are 3 specialized Function Codes which are shown on
the following Chart.
MASTER CODE
The Master Code is a four-digit Function Code used to
program Access Codes into the DK unit. The factory
default master code is 1 2 5 1.The Owner/Administrator
enters the Master Code to program the Access Codes
others will use to gain entry to the area controlled by
the unit. It is recommended that the Master Code be
re-programmed to a four-digit code of your choice.
Remember to make a note of the new Master Code. It
is the passwo
LATCH CODE
The Latch Code is a programmable four digit Function
Code used to toggle relay A. The Latch Code is used
to hold a gate or door open. For example, the home
owner or business administrator wants leave the gate
open for a period of time; say for a few hours during
a party or special function. While the Latch Code is
entered, the gate or door is open. Re-enter the Latch
Code to return the unit to normal operation (to close
and lock the gate or doorway.)
SLEEP CODE
The Sleep Code is a programmable four digit Function
Code which, when entered, disables all codes. No one
can use any of the Access Codes while the unit is in the
SLEEP mode. An example is if the user wants to deny all
access to a gated area for a period of time, he or she
enters the SLEEP CODE which essentially locks the unit.
Re-enter the Sleep Code to return the unit to normal
operation. An override code is provided.
Page 9 American Access Systems / Security Brands, Inc.
GOOD TONES and ERROR TONES
The DK unit sounds an audible tone each time a key is pressed. The star (ã) key serves as the clear key and a double
tone is sounded when the star (ã) key is pressed. The pound (#) key is the exit key and exits the programming mode
any time it is pressed.
• A “GOOD TONE” is an oscillating high tone. It is very distinct.
• An “ERROR TONE” is represented by a single low tone. It also is very distinct.
THE RED AND YELLOW LEDs
One Red (on the top left of the keypad) and one Yellow (on the top right of the keypad) LED are on the face of the
unit.
• The red LED illuminates during the relay(s) activation period.
• The yellow LED illuminates anytime the unit is in the program mode. During memory erasure or during the setup
routine, Both LEDs will flash repeatedly until theroutine or erasure is complete.
PROGRAMMING THE DK UNIT
The PROGRAM MODE is used to enter, delete, or change the codes or to set (energize) specific features of the unit
or how the DK unit interacts with other components in a system. Access the PROGRAM MODE by entering the Master
Code using the keypad. If the correct Master Code is entered the unit will reply with a GOOD TONE and the Yellow
LED will illuminate. In the Program Mode you have approximately 30 seconds between key presses. If the 30-second
time period is exceeded during programming, the unit will automatically exit the Programming Mode. No damage is
done to the programming. Simply complete the programming steps again.
NOTE: 1 2 5 1 WILL NOT OPEN THE GATE. 1 2 5 1 is the Master Code and allows access to the programming functions
only.
The Star (ã) and Pound (#) Keys
The star (ã) and pound (#) keys serve specific functions while in the IDLE or PROGRAMmode.
• Pressing the star (ã) key will always clear the entry and emits a double tone when it is pressed. FIX : IF YOU’VE
HIT THE FORTH KEY IS IT COMMITTED TO MEMORY. Press the star (ã) key if you want to delete entry. Note:
Pressing the star (ã) key will erase an entire entry. For example, if you enter 4 5 and realize that you wanted to
enter 5 4, press the star (ã) key and 4 5 will be erased. It is not necessary to press the star (ã) more than one
time.
• The pound (#) key serves as the programming exit key. Pressing (#) will exit the program mode. For example,
enter the programming mode, enter the Access Codes you wish to add to memory, and then press the pound
(#) key to exit the programming mode.
Page 10 American Access Systems / Security Brands, Inc.
PROGRAMMING THE DK UNIT
To access the program mode, enter the MASTER CODE. When the correct MASTER CODE is entered the yellow LED
will light and a GOOD TONE will sound. You can now enter any of ten programming SUB MODES described below.
SUB MODE NUMBER CODE
DESCRIPTION
1
Program an Access Code(s) (Relay A)
2
Delete an Access Code
3
Change Master Code
4
Set Sleep Code
5
Set Latch Code
6
Set Relay Output Times
7
Program an Access Code(s) (Relay B)
8
Enable / Disable the “3 Strikes-You’re Out” Feature
9
Program Event Input
0
Erase Memory
Program Relay “A” Access Codes -- Sub-Mode 1
To program Relay “A” access codes, use the following steps:
• Enter 1 2 5 1 (or, if the factory MASTER CODE has been changed, enter the programmed MASTER CODE)
• Unit will sound a GOOD TONE
• Enter the numeral 1
• Unit will sound a GOOD TONE
• Enter a four-digit code combination other than the MASTER CODE (for example enter 4 3 2 1)
• If you receive an ERROR TONE after an entry it means that particular code is already assigned and you must
select another code
• If you make a mistake during entry, press the star (ã) key, then re-enter the code.
• When a new code is accepted the unit will sound a GOOD TONE
• Continue to enter codes until you are finished
• When you are done, press the pound (#) key to exit the programming mode
NOTES: You will automatically be exited from the programming mode IF:
• The memory reaches capacity
• The memory is full, you will not be able to enter Sub-Mode 1 and you will receive an ERROR TONE if you try to
enter this Sub-Mode.
• To enter new codes if the memory is full, you must first delete codes some of thecodes already in memory.
• Contact AAS if there seems to be a problem programming additional codes.
Delete Individual Access Codes -- Sub-Mode 2
To delete programmed Access Codes:
• Enter the Master Code
• Unit will sound a GOOD TONE
• Enter the numeral 2
• Unit will sound a GOOD TONE
• Enter the Access Code you want to delete
• Unit will sound a GOOD TONE
• An ERROR TONE indicates that Access Code is not in the memory
• If you make an entry error, simply press the star (ã) key then enter the correct code
• Continue to enter Access Codes you wish to delete
• OR
• Enter pound (#) to exit the programming mode
NOTES:
• You can delete any Access or Function code that you wish with the exception of the MASTER CODE.
• If the code you want to delete is not found in memory, the unit will respond with an ERROR TONE and wait for
another code to be entered.
• A GOOD TONE will sound once the code has been found and deleted.
• You may continue deleting codes until you are done, then press the pound (#) key to exit the programming
mode.
Page 11 American Access Systems / Security Brands, Inc.
Change the Master Code -- Sub-Mode 3
To change the Master Code:
• Enter the current Master Code
• Unit will sound a GOOD TONE• Press the numeral 3
• Enter a new Master Code
• Unit will sound a GOOD TONE
• If you make an entry error, simply press the star (ã) key and enter the number you wish
• Press the pound (#) key to exit the programming modeNOTES:
• Be sure to make a note of the new Master Code. It is the password to system operation.
• If the Master Code has been forgotten or lost, and you cannot enter Sub-Mode 3, you must perform a Master
Reset which will reset the Master Code to 1 2 5 1. You can then use Sub-Mode 3 to change the Master Code.
Set Sleep Code -- Sub-Mode 4
DETAILS: The Sleep Code is used to disable all Relay A and Function Codes from the keypad. This feature is most
commonly used in applications where no entry is desired after hours. Relay B codes will continue to be valid from
the keypad. By connecting both relays in parallel, managers may be assigned Relay B codes and still gain access.
While in the SLEEP MODE, the yellow and red LED’s will flash every 3 seconds. To initialize the system back tonormal,
simply re-enter the Sleep Code. Should you lose or forget the Sleep Code and the unit is in the sleep mode you must
complete a Master Reset. See the instructions on pages 20 and 21.
To program or change the Sleep Code:
• Enter the current Master Code
• Press the numeral 4
• Unit will sound a GOOD TONE
• Enter a new Sleep Code (If you hear an ERROR TONE, select another code that is not already in use)
• Unit will sound a GOOD TONE
• If you make an entry error, simply press the star (ã) key and enter the number you wish
• When the new Sleep Code is accepted you will hear a GOOD TONE
• Press the pound (#) key to exit the programming mode
Set Latch Code -- Sub-Mode 5
DETAILS: The Latch Code toggles the state of the main relay (A) of the circuit board. The red LED will remain lit while
the relay is in the latched position. The latch code is useful in applications where the gate is desired to hold open. If
the operator’s close circuit is controlled by loops, timers, etc., they will be overridden by the latched state of the relay
and the gate will hold open. An “OPEN-OVERRIDE” circuit must exist in the operator in order to utilize this function.
If your gate cycles when this code is entered, your operator is not set up to utilize this function. Your local dealer or
distributor should be able to assist you if you have any specific questions.
To program or change the Latch Code:
• Enter the current Master Code
• Press the numeral 5
• Enter a new Latch Code (If you hear an ERROR TONE, select another code that is not already in use
• If you make an entry error, simply press the star (ã) key and enter the number you wish
• When a new Latch Code is accepted you will hear a GOOD TONE
• Press the pound (#) key to exit the programming mode
• Now, when the new Latch Code is entered, the RED LED will light and the gate will hold open
• When the new Latch Code is entered a second time the RED LED will go off and the gate will close
NOTE: On gates with a closing timer, the “TIMED DURATION” begins when the Latch Code is released.
Set Relay Output Times -- Sub-Mode 6
To set or change a Relay Output Time:
• Enter the current Master Code • Press the numeral 6
• Enter the Relay numeral (1 = Relay A; 2 = Relay B)
• Enter the desired Relay Output Time in seconds (i.e., enter 060 for 60 seconds)
• Press the pound (#) key to exit the programming mode
Program Relay “B” Access Codes -- Sub-Mode 7
To program Relay “B” Access Codes:
• Enter the current Master Code
• Press the numeral 7
• Enter a new Relay B Access Code (If you hear an ERROR TONE, select another code that is not already in use)
• When a new Latch Code is accepted you will hear a GOOD TONE
• Continue to enter new Relay B Access Codes
• If the memory becomes full, you will not be able to add more Relay B Access Codes
• Press the pound (#) key to exit the programming mode
Note: If the memory is full, you will not be able to access Sub-Mode 7. You will hear an ERROR TONE
instead.
Page 12 American Access Systems / Security Brands, Inc.
Enable or Disable the “Three Strikes … You’re Out” feature
-- Sub-Mode 8
DETAILS: This “anti-tampering” feature is designed to help keep an unauthorized individual from continually entering
codes until they “hit” a programmed Access Code. When the “Three Strikes …You’re Out” feature is enabled, if
anyone enters 3 incorrect Access Codes within 90 seconds, the “Three Strikes …You’re Out” feature will literally shut
down the unit for 90 seconds. During the first 30 seconds of the shut down, the LED’s will flash and a loud, highpitchealarm will sound to help draw attention to the unauthorized user. The unit will then continue in full lockout mode
for another 60 seconds even after the alarm ends. After 90 seconds, the unit will revert to the IDLE MODE and will
operate normally.
To toggle the “Three Strikes-You’re Out” feature on or off:
• Enter the current Master Code
• Unit will sound a GOOD TONE
• Press the numeral 8 and the unit will respond with either one or two tones
• A single tone indicates the “Three Strikes …You’re Out” will be enabled
• A double tone indicates the “Three Strikes …You’re Out” will be disabled
• Unit will sound a GOOD TONE
• Enter the current Master Code a second time to accept the enabled or disabled selection• If you make an
entry error, simply press the star (ã) key
• Press the pound (#) key to exit the programming mode
Note: Make sure to wait for the unit to sound a GOOD TONE between selections. Depending upon
the installation, there are times when a few seconds may go by before you hear a GOOD TONE. Just
make sure that you hear a GOOD TONE between selections. If you do not want to change the state
of the “Three Strikes …You’re Out”, press the pound (#) key to exit.
Event Input -- Sub-Mode 9
DETAILS: Programming Sub-Mode 9 allows a user with Master Code privileges to program the unit to connect to an
external device to control a specific function.
Note: Relay A codes can be turned off by an external switch. When inactive, all Relay “A” codes
will be disabled. However, the Relay “B,” program and function codes will continue to be accessible
to the Master user.
NOTE: If you do not wish to toggle the MODE that the unit reports, enter pound (#) key to exit. Event
Input can be programmed 4 separate ways:
1. To program Event Input as Remote Inactive:
• Enter the MASTER CODE
• Unit will sound a GOOD TONE
• Enter the numeral 9 (Unit will sound the Current Mode*)
• Unit will sound a GOOD TONE
• Enter the numeral 1
• Unit will sound a GOOD TONE
2. To program the Event Input as an Arming Circuit:
• Enter the MASTER CODE
• Unit will sound a GOOD TONE
• Enter the numeral 9 (Unit will sound the Current Mode*) followed by a GOOD TONE
• Enter the numeral 2
• Unit will sound a GOOD TONE
3. To program the Event Input as Remote Open:
• Enter MASTER CODE
• Unit will sound a GOOD TONE
• Enter the numeral 9 (Unit will sound Current Mode*) followed by a GOOD TONE
• Enter the numeral 3
• Unit will sound two quick tones in succession then wait for input
• Enter the Relay to Activate
Enter the numeral 1 to activate relay A
OR
Enter the numeral 2 to activate relay B
• Unit will sound a GOOD TONE4. To DISABLE the Event Input:
• Enter the MASTER CODE • Enter the numeral 9 (Unit will sound Current Mode*)
• Enter the numeral 0 to Disable
• Unit will sound a GOOD TONE
*Current Modes
Single Tone Indicates:
Remote Inactive Mode is Enabled
Double Tone Indicates:
Arming Circuit Mode is Enabled
Triple Tone Indicates:
Remote Open Mode is Enabled
GOOD TONE Only:
Event Input Disabled
NOTE: If you do not wish to toggle the MODE that the unit reports, enter # to exit.
Page 13 American Access Systems / Security Brands, Inc.
Erase All Codes -- Sub-Mode 0
Caution: This is a destructive Programming Mode. Completing the following steps will erase all
Access Codes except for the factory default Master Code (1 2 5 1). Use with Caution.
DETAILS: This Sub-Mode should rarely be used unless you want to completely erase all Access Codes entered. This
action will not change the Master Code.
To erase all Access Codes and Function Codes
• Enter the Master Code (The 1 2 5 1 cannot be deleted)
• Enter the numeral 0
• Both the Red and Yellow LEDs will flash several times and the unit will sound a GOODTONE once all of the
memory is cleared.
• Enter the Master Code to complete the process
• If the sequence is not validated by the unit, you will receive an ERROR TONE and be exited from this program
mode
• A GOOD TONE will sound to indicate all memory is cleared.
RESETTING THE DK UNIT
The Advantage DK has two special reset types: Master Reset and Unit Reset. Choose the procedure that you want
to use carefully.
Master Reset
• Should be used if the Master Code is lost or forgotten. The procedure will reset the Master Code to the 1 2 5 1.
• Should be used if the unit is in the Latch or Sleep Mode and the Latch or Sleep code is lost or forgotten.
• When a Master Reset is performed, Access Codes and Functions Codes are retained in memory and the unit
does not require complete reprogramming.
Unit Reset
• Should only be used if the Advantage DK is to be completely reset back to factory default settings.
• ALL ACCESS and FUNCTION CODES ARE LOST during a Unit Reset.
• The Master code is reset to 1 2 5 1 following a Unit Reset.
MASTER RESET
Follow these steps exactly. If you make an error, an ERROR will occur (you will hear a low ERROR tone) and you will
need to start over from Step 1.
1. Open the unit face plate using the key provided.
2. Disconnect power from the unit by gently pulling the wire harness connector away from the board. Make sure
to note the orientation of the connector.
3. Press and hold down the RESET button and reconnect power to the board by gently sliding the harness
connector back into place on the circuit board(you will hear 1 tone), then release the RESET button. (See
location Board Layout diagram, page 22 )
4. Press the star (*)(*)(*) key three times.
5. The Master Code is now reset to the factory default (1 2 5 1)
6. Close the face plate.
7. Program a new Master Code if you choose to do so. Be sure to make a note of the new Master Code.
UNIT RESET
NOTE: ALL ACCESS CODES and FUNCTION CODES are lost when performing a Unit Reset.
Follow these steps exactly. If you make an error, an ERROR will occur (a low-pitch ERROR tone will sound) and you will
need to start over from Step 1.
1. Open the faceplate.
2. Disconnect the power from the unit by gently pulling the wire harness away from the board. Make sure to
note the orientation of the connector.
3. Press and hold down the RESET button and reconnect power to the board by gently sliding the harness
connector back into place on the circuit board, then release the RESET button. (See location Board Layout
diagram, page 22)
4. Enter (#) (ã) (#) (Pound, Star, Pound)
5. The unit will respond with a GOOD TONE
6. Enter the MASTER CODE (1 2 5 1) from the keypad. The unit will flash the LED’sseveral times and then go into
an endless cycle of tones.
7. While the cycle of tones continues, disconnect and then immediately reconnect power to the unit using the
circuit board harness connector. The unit will then go through the “First Time Power Up” sequence. (See
page 5).
8. The DK is now completely reset. All programming is erased.
Page 14 American Access Systems / Security Brands, Inc.
Troubleshooting
Problem
Solution
When I enter 1 2 5 1 on the keypad the gate will
not open.
1 2 5 1 is the Master Code or programming access code.
It will not open the gate unless the unit is in sleep mode.
Program a gate access code into the unit using Sub-Mode 1
(listed in the programming instructions).
No response from keypad.
Adjust the MIC and /or SPEAKER pots on circuit board to
desired levels. A m Verify power input across the two white
wires on the main harness. Check blue night light LED’s to
see if they are on. Check for burn marks on the circuit board
from a lighting surge. Contact American Access Systems,
Inc. aximum of 5 turns clockwise is allowed.
After I enter the latch code to hold the gate open
it closes or cycles open and shut. When I enter a
valid Access Code the gate does not open.
An open override circuit must be enabled in the gate
operator to prevent the timer circuit from overriding the
keypad when it is in a latch mode. Contact Gate Operator
manufacturer.
When I enter a valid Access Code the gate does
not open.
Locate the two wires attached to the Brown and Orange
wires on the main wire harness, then, touch them together.
If the gate does not open, check wiring or the connection
terminals on gate operator. If the gate opens, contact
American Access Systems.
I connected the two white power wires together to
one power source wire and the other power source
wire to the green wire but the keypad doesn’t work.
The green wire is for EARTH GROUND only. Connect one
white wire to one power source wire and the other white
wire to the second power source wire.
When I press 1 2 5 1 on the keypad nothing happens and I hear an endless set of error tones.
Contact American Access Systems Inc.
I want to reset my keypad but when I push the reset
button nothing happens.
Consult instructions regarding MASTER and UNIT reset for
proper reset sequence.
Page 15 American Access Systems / Security Brands, Inc.
Customer Service and Tech Support
Customer Service: 303-799-9757
Customer service is available free of charge. Hours are 8:00 a.m. to 4:30 p.m. MST. If you call, please
have your Model and Serial Number to help our Technicians assist you.
E-Mail: customerservice@securitybrandsinc.com
Technical Support: 303-799-9757
Technical support is available free of charge. Hours are 8:00 a.m. to 4:30 p.m. MST. If you call, please
have your Model and Serial Number to help our Technicians assist you.
E-Mail: techsupport@securitybrandsinc.com
SECURITY BRANDS INC
1675 West Yale Ave.
Englewood, CO 80110
phone: 303-799-9757
fax: 303-799-9756
sales@securitybrandsinc.com
www.americanaccess.com
Page 16 American Access Systems / Security Brands, Inc.
Notes
Use this space to keep a record of Access Codes and the MASTER Code
Page 17 American Access Systems / Security Brands, Inc.
Notes
Use this space to keep a record of Access Codes and the MASTER Code
Page 18 American Access Systems / Security Brands, Inc.
Notes
Use this space to keep a record of Access Codes and the MASTER Code
Page 19 American Access Systems / Security Brands, Inc.
“Your partner in access control”
www.securitybrandsinc.com
SECURITY BRANDS INC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising