Product Manual - PCB Piezotronics

Product Manual - PCB Piezotronics
Model 076C31
10-32 plug connector kit, includes crimping tool and (20) coaxial conn. (EB
Installation and Operating Manual
For assistance with the operation of this product,
contact PCB Piezotronics, Inc.
Toll-free: 800-828-8840
24-hour SensorLine: 716-684-0001
Fax: 716-684-0987
E-mail: info@pcb.com
Web: www.pcb.com
Warranty, Service, Repair, and
Return Policies and Instructions
The information contained in this document supersedes all similar information that
may be found elsewhere in this manual.
Total Customer Satisfaction – PCB
Piezotronics guarantees Total Customer
Satisfaction. If, at any time, for any
reason, you are not completely satisfied
with any PCB product, PCB will repair,
replace, or exchange it at no charge.
You may also choose to have your
purchase price refunded in lieu of the
repair, replacement, or exchange of the
product.
Service – Due to the sophisticated
nature of the sensors and associated
instrumentation provided by PCB
Piezotronics, user servicing or repair is
not recommended and, if attempted,
may void the factory warranty. Routine
maintenance, such as the cleaning of
electrical connectors, housings, and
mounting surfaces with solutions and
techniques that will not harm the
physical material of construction, is
acceptable. Caution should be observed
to insure that liquids are not permitted to
migrate into devices that are not
hermetically sealed. Such devices
should only be wiped with a dampened
cloth and never submerged or have
liquids poured upon them.
Repair – In the event that equipment
becomes damaged or ceases to
operate, arrangements should be made
to return the equipment to PCB
Piezotronics for repair. User servicing or
repair is not recommended and, if
attempted, may void the factory
warranty.
Calibration – Routine calibration of
sensors and associated instrumentation
is recommended as this helps build
confidence in measurement accuracy
and
acquired
data.
Equipment
calibration
cycles
are
typically
established by the users own quality
regimen. When in doubt about a
calibration cycle, a good “rule of thumb”
is to recalibrate on an annual basis. It is
also good practice to recalibrate after
exposure to any severe temperature
extreme, shock, load, or other
environmental influence, or prior to any
critical test.
PCB Piezotronics maintains an ISO9001 certified metrology laboratory and
offers calibration services, which are
accredited by A2LA to ISO/IEC 17025,
with full traceability to SI through
N.I.S.T. In addition to the normally
supplied calibration, special testing is
also available, such as: sensitivity at
elevated or cryogenic temperatures,
phase response, extended high or low
frequency response, extended range,
leak testing, hydrostatic pressure
testing, and others. For information on
standard recalibration services or
special testing, contact your local PCB
Piezotronics
distributor,
sales
representative, or factory customer
service representative.
Returning Equipment – Following
these procedures will insure that your
returned materials are handled in the
most
expedient
manner.
Before
returning any equipment to PCB
Piezotronics,
contact
your
local
distributor, sales representative, or
factory customer service representative
to obtain a Return Warranty, Service,
Repair, and Return Policies and
Instructions Materials Authorization
(RMA) Number. This RMA number
should be clearly marked on the outside
of all package(s) and on the packing
list(s) accompanying the shipment. A
detailed account of the nature of the
problem(s) being experienced with the
equipment should also be included
inside the package(s) containing any
returned materials.
A Purchase Order, included with the
returned materials, will expedite the
turn-around of serviced equipment. It is
recommended to include authorization
on the Purchase Order for PCB to
proceed with any repairs, as long as
they do not exceed 50% of the
replacement cost of the returned
item(s). PCB will provide a price
quotation
or
replacement
recommendation for any item whose
repair costs would exceed 50% of
replacement cost, or any item that is not
economically feasible to repair. For
routine
calibration
services,
the
Purchase
Order
should
include
authorization to proceed and return at
current pricing, which can be obtained
from a factory customer service
representative.
Warranty – All equipment and repair
services provided by PCB Piezotronics,
Inc. are covered by a limited warranty
against
defective
material
and
workmanship for a period of one year
from date of original purchase. Contact
PCB for a complete statement of our
warranty. Expendable items, such as
batteries and mounting hardware, are
not covered by warranty. Mechanical
damage to equipment due to improper
use is not covered by warranty.
Electronic circuitry failure caused by the
introduction of unregulated or improper
excitation
power
or
electrostatic
discharge is not covered by warranty.
Contact Information – International
customers should direct all inquiries to
their local distributor or sales office. A
complete list of distributors and offices
can be found at www.pcb.com.
Customers within the United States may
contact their local sales representative
or
a
factory
customer
service
representative. A complete list of sales
representatives can be found at
www.pcb.com.
Toll-free
telephone
numbers for a factory customer service
representative,
in
the
division
responsible for this product, can be
found on the title page at the front of this
manual. Our ship to address and
general contact numbers are:
PCB Piezotronics, Inc.
3425 Walden Ave.
Depew, NY14043 USA
Toll-free: (800) 828-8840
24-hour SensorLineSM: (716) 684-0001
Website: www.pcb.com
E-mail: info@pcb.com
PCB工业监视和测量设备 - 中国RoHS2公布表
PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table
有害物质
镉
汞
铅 (Pb)
六价铬 (Cr(VI))
多溴联苯 (PBB)
多溴二苯醚 (PBDE)
部件名称
(Hg)
(Cd)
O
O
O
O
O
O
住房
X
O
O
O
O
O
PCB板
O
O
O
O
O
O
电气连接器
X
O
O
O
O
O
压电晶体
O
O
O
O
O
O
环氧
O
O
O
O
O
O
铁氟龙
O
O
O
O
O
O
电子
O
O
X
O
O
O
厚膜基板
O
O
O
O
O
O
电线
X
O
O
O
O
O
电缆
O
O
O
O
O
O
塑料
X
O
O
O
O
O
焊接
X
O
O
O
O
O
铜合金/黄铜
本表格依据 SJ/T 11364 的规定编制。
O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。
铅是欧洲RoHS指令2011/65/ EU附件三和附件四目前由于允许的豁免。
CHINA RoHS COMPLIANCE
Component Name
Hazardous Substances
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Chromium VI
Compounds
(Cr(VI))
Housing
O
O
O
PCB Board
X
O
O
Electrical
O
O
O
Connectors
Piezoelectric
X
O
O
Crystals
Epoxy
O
O
O
Teflon
O
O
O
Electronics
O
O
O
Thick Film
O
O
X
Substrate
Wires
O
O
O
Cables
X
O
O
Plastic
O
O
O
Solder
X
O
O
Copper Alloy/Brass
X
O
O
This table is prepared in accordance with the provisions of SJ/T 11364.
Polybrominated
Biphenyls
(PBB)
Polybrominated
Diphenyl
Ethers (PBDE)
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit
requirement of GB/T 26572.
X: Indicates that said hazardous substance contained in at least one of the homogeneous materials for this part is above
the limit requirement of GB/T 26572.
Lead is present due to allowed exemption in Annex III or Annex IV of the European RoHS Directive 2011/65/EU.
DOCUMENT NUMBER: 21354
DOCUMENT REVISION: C
ECN: 45605
INSTALLATION INSTRUCTIONS
Model 076C31
10-32 Connector Kit
Connector Assembly Procedure
1 Slide strain relief boot and cable ferrule onto cable.
2 Strip cable layers to the lengths indicated in the figure below.
3 (This step only required if using PCB 003 or 006 cable) Remove black outer layer
from the dielectric using tweezers or sharp blade. Ensure that the dielectric layer
is not cut in the process. Also scrape the black coating off of the center conductor
using a sharp blade. Use caution not to cut into the conductor.
4 Carefully slide jerk ring onto braid, non-split end first, and crimp jerk ring lightly
with pliers to temporarily hold in place. Slide cable ferrule up so that it just
touches jerk ring. Ensure that jerk ring does not slip forward over dielectric.
(continued on back)
PCB Piezotronics, Inc. claims proprietary rights in the information disclosed hereon. This information is furnished in confidence on the express
understanding that neither it nor any reproduction thereof will be disclosed to others or used for any purpose not expressly agreed upon by PCB Piezotronics, Inc.
PCB PIEZOTRONICS, INC. • WWW.PCB.COM
INSTALLATION INSTRUCTIONS
5 Slide housing/coupling nut assembly over jerk ring and cable ferrule. Crimp
housing with crimping tool provided. Use hex cutout labeled “A”.
6 Trim center conductor down to white insulator inside housing/coupling nut so that
only 1/64" is exposed. Insert pin contact (barbed end out) into small hole at the
end of the Pin Installation Tool. Loosen the end of the tool approximately 3 turns.
Screw the tool into housing/coupling nut as far as possible. Tighten the end of the
tool completely, forcing the pin contact into the white insulator. Remove the
connector from the tool.
7 Pull up the strain relief boot until it locks into place.
Document Number 39427 Rev. NR
3425 Walden Avenue, Depew, NY 14043-2495 USA PCB® toll-free 800-828-8840 24-hour SensorLineSM 716-684-0001
FAX 716-684-0987 E-mail info@pcb.com Website www.pcb.com
ISO 9001 CERTIFIED
PCB-076C31-0108
© 2000 PCB Group, Inc. In the interest of constant product improvement, specifications are subject to change without notice. SensorLine is a service mark of PCB Group, Inc.
PCB is a registered trademark of PCB Group, Inc. All other trademarks are properties of their respective owners.
Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising