MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide (p/n

MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide (p/n
MK4000 MICROKIOSK
FOR CE .NET 5.0
PRODUCT REFERENCE
GUIDE
MK4000 MICROKIOSK FOR CE .NET 5.0
PRODUCT REFERENCE GUIDE
72E-121864-05
Revision A
September 2015
ii
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
© 2015 ZIH Corp and/or its affiliates. All rights reserved.
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means,
without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying,
recording, or information storage and retrieval systems. The material in this manual is subject to change
without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on
a licensed basis. Zebra grants to the user a non-transferable and non-exclusive license to use each software
or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be
assigned, sublicensed, or otherwise transferred by the user without prior written consent of Zebra. No right to
copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall
not modify, merge, or incorporate any form or portion of a licensed program with other program material, create
a derivative work from a licensed program, or use a licensed program in a network without written permission
from Zebra. The user agrees to maintain Zebra’s copyright notice on the licensed programs delivered
hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not
to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any
portion thereof.
Zebra reserves the right to make changes to any software or product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any
product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any Zebra Technologies
Corporation, intellectual property rights. An implied license only exists for equipment, circuits, and subsystems
contained in Zebra products.
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All
other trademarks are the property of their respective owners.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
iii
Revision History
Changes to the original guide are listed below:
Change
Date
Description
-01 Rev A
9/2009
Initial release
-02 Rev A
5/2010
Add Power-over-Ehernet (POE) information, remove instructions involving Initial
Program Loader (IPL)
-03 Rev A
8/2011
Removed EMDK for Java information
-04 Rev A
3/2015
Zebra rebranding
-05 Rev A
9/2015
Updated scanner configuration list
iv
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
TABLE OF CONTENTS
About This Guide
Introduction .....................................................................................................................................
Configurations.................................................................................................................................
Chapter Descriptions ......................................................................................................................
Notational Conventions...................................................................................................................
Related Publications .......................................................................................................................
Service Information .........................................................................................................................
Chapter 1: MK4000 Introduction
Overview ........................................................................................................................................
MK4000 Parts ................................................................................................................................
Touch Screen LCD ..................................................................................................................
Speakers ..................................................................................................................................
Microphone ..............................................................................................................................
Scanner Window ......................................................................................................................
External Ports ..........................................................................................................................
MK4000 Features ..........................................................................................................................
Bar Code Scanner/Imager .......................................................................................................
Software ...................................................................................................................................
Touch Screen ...........................................................................................................................
Memory ....................................................................................................................................
Connectivity Options ................................................................................................................
Micro SD Card Slot ..................................................................................................................
Power .......................................................................................................................................
Magnetic Stripe Reader (Optional) ..........................................................................................
Mounting Options .....................................................................................................................
Developer Kits ..........................................................................................................................
Bar Code Decoding ........................................................................................................................
Scanning with the MK4000 ......................................................................................................
Imaging with the MK4000 8
Chapter 2: Installation
Overview ........................................................................................................................................
Unpacking the MK4000 ..................................................................................................................
Removing the Screen Protector .....................................................................................................
Inserting a Micro SD Card ..............................................................................................................
ix
ix
ix
x
xi
xi
1-1
1-1
1-1
1-1
1-1
1-2
1-3
1-4
1-4
1-4
1-4
1-4
1-4
1-4
1-4
1-4
1-5
1-5
1-6
1-6
2-1
2-1
2-2
2-2
vi
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Connecting the MK4000 ................................................................................................................
AC Power Supply ....................................................................................................................
USB Connection ......................................................................................................................
Wired Ethernet Connection ......................................................................................................
MK4000 Mounting ..........................................................................................................................
Using a VESA Mount ...............................................................................................................
Using the MK4000 Wall Mount Kit ...........................................................................................
Using the MK4000 Pole Mount Kit ...........................................................................................
Magstripe Reader Installation ........................................................................................................
Card Swiping ............................................................................................................................
Advertisement Insert Mounting ......................................................................................................
2-2
2-2
2-3
2-3
2-5
2-5
2-6
2-7
2-9
2-11
2-12
Chapter 3: Configuration
Overview ........................................................................................................................................
System Configuration Manager .....................................................................................................
File Types ................................................................................................................................
User Interface ..........................................................................................................................
File Deployment .......................................................................................................................
Local Configuration Using the Microsoft Windows Control Panel ..................................................
Configuration via Registry File .......................................................................................................
Rebooting the MK4000 ............................................................................................................
3-1
3-1
3-1
3-2
3-4
3-4
3-4
3-4
Chapter 4: System Features
Overview ........................................................................................................................................
RegMerge and CopyFiles ..............................................................................................................
Accessing the Windows® CE Desktop ..........................................................................................
Network Time Update: SNTP Client ..............................................................................................
Memory Management ....................................................................................................................
Flash: Nonvolatile (Persistent) Memory ...................................................................................
RAM: Volatile (Non-Persistent) Memory ..................................................................................
Browser Applications .....................................................................................................................
Loading Additional Fonts on the MK4000 ......................................................................................
Using Additional Fonts in Native Applications ..........................................................................
Using Additional Fonts in Managed Applications .....................................................................
Using Additional Fonts in Browser Applications .......................................................................
Things to Consider when Using Additional Fonts ....................................................................
Input Panel (Virtual Keyboard) .......................................................................................................
Microsoft Applications ....................................................................................................................
4-1
4-2
4-2
4-2
4-2
4-2
4-2
4-3
4-3
4-4
4-4
4-4
4-4
4-5
4-5
Chapter 5: Application Deployment
Overview ........................................................................................................................................
Enterprise Mobility Developer Kit (EMDK) for C ......................................................................
Enterprise Mobility Developer Kit (EMDK) for .NET .................................................................
PocketBrowser for the Web .....................................................................................................
Device Configuration Package .................................................................................................
Platform SDK ...........................................................................................................................
Installing Enterprise Mobility Developer Kits ............................................................................
Installing Other Development Software ...................................................................................
Deployment ....................................................................................................................................
ActiveSync ...............................................................................................................................
OS Update ...............................................................................................................................
Terminal Configuration Manager (TCM) ..................................................................................
Rapid Deployment Client .........................................................................................................
AirBEAM Smart ........................................................................................................................
Flash Storage ................................................................................................................................
5-1
5-1
5-2
5-3
5-3
5-3
5-4
5-4
5-4
5-5
5-7
5-8
5-17
5-17
5-18
Table of Contents
FFS Partitions ..........................................................................................................................
Working with FFS Partitions .....................................................................................................
Non-FFS Partitions ..................................................................................................................
Downloading Partitions to the MK4000 ....................................................................................
vii
5-18
5-18
5-19
5-19
Appendix A: Technical Specifications
Technical Specifications ................................................................................................................ A-1
Appendix B: Wireless Configuration
Overview ........................................................................................................................................
Wireless Applications .....................................................................................................................
Signal Strength Icon .......................................................................................................................
Turning the WLAN Radio On and Off ............................................................................................
Find WLANs Application ................................................................................................................
Profile Editor Wizard ......................................................................................................................
Profile ID ..................................................................................................................................
Operating Mode .......................................................................................................................
Ad-Hoc .....................................................................................................................................
Security Mode ..........................................................................................................................
Authentication ..........................................................................................................................
Tunneled Authentication ..........................................................................................................
User Certificate Selection ........................................................................................................
Server Certificate Selection .....................................................................................................
Encryption ................................................................................................................................
IP Address Entry ......................................................................................................................
Transmit Power ........................................................................................................................
Battery Usage ..........................................................................................................................
Manage Profiles Application ..........................................................................................................
Manage Certificates .......................................................................................................................
Certificate Properties ...............................................................................................................
Import a Certificate ...................................................................................................................
Delete a Certificate ..................................................................................................................
Manage PACs ................................................................................................................................
PAC Properties ........................................................................................................................
Delete PAC ..............................................................................................................................
Wireless Status Application ...........................................................................................................
Signal Strength Window ...........................................................................................................
Current Profile Window ............................................................................................................
IPv4 Status Window .................................................................................................................
Wireless Log Window ..............................................................................................................
Versions Window .....................................................................................................................
Wireless Diagnostics Application ...................................................................................................
ICMP Ping Window ..................................................................................................................
Graphs .....................................................................................................................................
Trace Route Window ...............................................................................................................
Known APs Window .................................................................................................................
Options ...........................................................................................................................................
Operating Mode Filtering .........................................................................................................
Regulatory Options ..................................................................................................................
Band Selection .........................................................................................................................
System Options ........................................................................................................................
Auto PAC Settings ...................................................................................................................
Change Password ....................................................................................................................
Export .......................................................................................................................................
B-1
B-2
B-3
B-3
B-4
B-5
B-5
B-6
B-8
B-9
B-10
B-11
B-13
B-14
B-19
B-23
B-25
B-27
B-28
B-31
B-31
B-32
B-32
B-33
B-33
B-33
B-34
B-35
B-36
B-37
B-38
B-39
B-39
B-40
B-40
B-41
B-42
B-43
B-43
B-44
B-44
B-45
B-45
B-46
B-47
Table of Contents
Cold Boot Persistence ...................................................................................................................
Registry Settings ............................................................................................................................
Log On/Off Application ...................................................................................................................
User Already Logged In ...........................................................................................................
No User Logged In ...................................................................................................................
B-48
B-48
B-49
B-49
B-50
Appendix C: Troubleshooting
Overview ........................................................................................................................................
Troubleshooting Notes .............................................................................................................
Troubleshooting .............................................................................................................................
MK4000 Version Information .........................................................................................................
C-1
C-1
C-1
C-4
Appendix D: MK4000 Demo
Overview ........................................................................................................................................
Price Check #1 ...............................................................................................................................
Price Check #2 ...............................................................................................................................
Special Order Pick Up ....................................................................................................................
Loyalty Coupon Printing .................................................................................................................
Loyalty Coupon Redemption (Mailer) ............................................................................................
Cell Phone Coupon ........................................................................................................................
Lottery Win Verification ..................................................................................................................
Employee Application ....................................................................................................................
D-1
D-1
D-2
D-2
D-3
D-3
D-3
D-4
D-4
Index
viii
ABOUT THIS GUIDE
Introduction
The MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide provides information on installing, operating,
and programming the MK4000.
NOTE
Unless otherwise noted, the term MK4000 refers to all configurations of the device.
Configurations
This guide includes the following configurations:
• MK4000-030PZ0GWTWR - Imager, Ethernet
• MK4000-0U0PZ0GWTWR - Laser scanner, Ethernet
• MK4900-A30PZ0GWTWR - Imager, 802.11 a/b/g
• MK4900-AU0PZ0GWTWR - Laser scanner, 802.11 a/b/g
Chapter Descriptions
Following are brief descriptions of each chapter in this guide.
• Chapter 1, MK4000 Introduction provides an overview of the MK4000 that includes parts of the MK4000,
features, and scanning modes.
• Chapter 2, Installation describes the hardware setup and installation of the MK4000.
• Chapter 3, Configuration describes the configuration parameters of the MK4000.
• Chapter 4, System Features describes the wide range of capabilities used to support independent
application development on the MK4000.
• Chapter 5, Application Deployment describes the software development environments and how to install and
upgrade applications and images.
x
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
• Appendix A, Technical Specifications provides technical information about the MK4000.
• Appendix B, Wireless Configuration describes how to configure the Spectrum24 wireless connection.
• Appendix C, Troubleshooting provides troubleshooting procedures for correcting problems encountered
with the MK4000.
• Appendix D, MK4000 Demo provides information on the MK4000 demo which illustrates device
functions.
Notational Conventions
This document uses these conventions:
• “User” refers to anyone using an application on the terminal.
• “Device” refers to the MK4000.
• Italics are used to highlight specific items in the general text, and to identify chapters and sections in this
and related documents. It also identifies names of windows, menus, menu items, and fields within
windows.
• Bold identifies buttons to be tapped or clicked.
• Bullets (•) indicate:
• lists of alternatives or action items.
• lists of required steps that are not necessarily sequential.
• Numbered lists indicate a set of sequential steps, i.e., those that describe step-by-step procedures.
NOTE
This symbol indicates something of special interest or importance to the reader. Failure to read the note
will not result in physical harm to the reader, equipment or data.
CAUTION
WARNING!
This symbol indicates that if this information is ignored, the possibility of data or material damage may
occur.
This symbol indicates that if this information is ignored the possibility that serious personal
injury may occur.
About This Guide
xi
Related Publications
Following is a list of documents and software that provide additional information about configuring the MK4000:
• MK500/MK4000 Quick Reference Guide, p/n 72-112230-xx
• MK4000 Platform Software Development Kit (PSDK)
• Enterprise Mobility Developer Kit (EMDK) for C
• Enterprise Mobility Developer Kit (EMDK) for .NET
• PocketBrowser
• Device Configuration Package (DCP)
• Microsoft Applications for Mobile and Win CE 5.0 User Guide, p/n 72E-78456-xx
• Application Guide for Devices, p/n 72E-68901-xx
• AirBEAM® Package Builder Product Reference Guide, p/n 72-55769-xx.
• AirBEAM® Smart Windows® CE Client Product Reference Guide, p/n 72-63060-xx
• MSP 3.X User’s Guide, p/n 72E-100158-xx
For the latest version of these guides and software, visit: http://www.zebra.com/support
Service Information
If you have a problem with your equipment, contact Zebra support for your region. Contact information is
available at: http://www.zebra.com/support.
When contacting Zebra support, please have the following information available:
• Serial number of the unit
• Model number or product name
• Software type and version number
Zebra responds to calls by e-mail, telephone or fax within the time limits set forth in service agreements.
If your problem cannot be solved by Zebra support, you may need to return your equipment for servicing and
will be given specific directions. Zebra is not responsible for any damages incurred during shipment if the
approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your business product from a Zebra business partner, please contact that business partner
for support.
xii
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
CHAPTER 1 MK4000 INTRODUCTION
Overview
The MK4000 MicroKiosk provides retail consumers access to data critical to making an informed purchasing
decision. The MK4000 verifies prices on bar coded merchandise and obtains up-to-the-minute information on
in-store promotions. Its easy-to-read display can be used as an electronic billboard for instant in-store
merchandising and multimedia presentations to promote seasonal sales and upcoming events. The touch
screen and programmable function buttons enhance in-store applications and allow customer interaction.
MK4000 Parts
MK4000 parts include:
• Touch screen
• Speakers
• Scanner window
• External ports.
See Figure 1-1 on page 1-2 and Figure 1-2 on page 1-3 for illustrations.
Touch Screen LCD
The full color 12.1 inch diagonal full XVGA (1024 X 760 pixels) or SVGA (800 X 600 pixels) LCD is ideal for
presenting text, graphics, and video. The touch screen accommodates greater user interaction and enhances
custom designed applications.
Speakers
The MK4000 speakers are ideal for multimedia applications.
Microphone
The MK4000 includes a microphone built into its front housing.
1-2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Scanner Window
The scanner window protects the scan engine.
Microphone
Touch Screen
Speakers
Scanner Window
Figure 1-1 MK4000 Front View
MK4000 Introduction
Cable Run
Mounting Hole (4)
Cable Run
Cable Run
Power
RJ45 (Ethernet)
Micro SD Card Slot
Mini USB Host/Client Port
Mini USB Host Ports (2)
Headset Jack
Figure 1-2 MK4000 Rear View
External Ports
The MK4000 has the following external ports:
Power Port
A power supply connects to the power port (2.0 mm barrel jack connector) on the MK4000. For more
information, see AC Power Supply on page 2-2.
Mini USB Ports
The MK4000 includes a Mini USB 1.1 host/client port and two Mini USB 1.1 host ports for peripheral
connections. For more information, see USB Connection on page 2-3.
RJ45 Ethernet/Bias-T
Wired/Wireless Ethernet: Power through AC Outlet
The Ethernet / Bias-T (10-conductor RJ45) port accommodates Ethernet data connection. The MK4000
receives power through the Zebra approved power supply.
Wired Ethernet: Power through Power-over-Ethernet
The MK4000 supports Power-over-Ethernet (POE), 802.3at standard. An Ethernet (10/100Base-T) cable
connected to the Ethernet port provides both data communication and power to the MK4000.
1-3
1-4
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Headset Jack
The MK4000 includes a port for headset connection.
CAUTION
When connecting a headset, Zebra recommends using cable ties or other securing mechanisms
outside the unit to provide strain relief.
MK4000 Features
Bar Code Scanner/Imager
The laser-based MK4000 decodes all traditional 1D bar codes (including RSS bar code type). The
imager-based version decodes 1D bar codes as well as 2D symbologies such as PDF417. See Bar Code
Decoding on page 1-6.
Software
Standard well-supported operating system and development tools ease application development for the
Microsoft® Windows® CE .NET operating system: Embedded Visual C/C++ 4.0, Visual Studio.NET, Internet
Explorer 6.0, C#, VisualBasic.NET, and Windows CE Media Player.
Touch Screen
The touch screen provides user interaction and enhances the capabilities of custom applications.
Memory
The MK4000 standard system configuration contains 128 MB flash/128 MB DRAM. The flash memory is
non-volatile and stores the system firmware, user applications, and data.
Connectivity Options
MK4000 connectivity options include USB, wired 10/100 Mbps Ethernet, or wireless 802.11 a/b/g Mbps.
Micro SD Card Slot
The MK4000 contains a slot for micro SD cards of up to 8 GB.
Power
To supply power, use the standard Zebra approved power supply or 802.3at Power-over-Ethernet certified
equipment.
Magnetic Stripe Reader (Optional)
An optional three-track Magnetic Stripe Reader (MSR) module attaches to the MK4000 and adds the ability to
read and process loyalty card and credit card transactions. The MSR connects via USB to the MK4000.
MK4000 Introduction
1-5
Mounting Options
You can mount the MK4000 on a desktop or wall using a commercially-available bracket or stand that
conforms to the 100 mm VESA Flat Panel Monitor Physical Mounting Interface (FPMPMI™) mounting
standards. See MK4000 Mounting on page 2-5.
Developer Kits
The following developer kits are available for the MK4000:
• EMDK for C (see Enterprise Mobility Developer Kit (EMDK) for C on page 5-1) for developing native
C/C++ applications.
• EMDK for .NET (see Enterprise Mobility Developer Kit (EMDK) for .NET on page 5-2) for developing
managed .NET applications in C# or VB.NET.
• PocketBrowser (see PocketBrowser for the Web on page 5-3) for web development.
1-6
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Bar Code Decoding
The MK4000 decodes any traditional retail 1D or PDF417 (imager-based only) bar code presented in its field of
view.
Scanning with the MK4000
When scanning a bar code using the laser-based MK4000:
• Hold the bar code at an angle which does not cause specular reflection (see Specular Reflection on page
1-7).
• Hold the bar code close for small bar codes and farther away for large bar codes.
• The MK4000 beeps to indicate a successful decode.
Figure 1-3 Scanning with the MK4000
The scan beam does not have to be perfectly parallel with the top and bottom of the symbol (up to a 4o tilt is
permitted). Ensure the symbol is in good condition.
MK4000 Introduction
1-7
Specular Reflection
When laser beams reflect directly back into the scanner from the bar code, they can “blind” the scanner and
make decoding difficult. This phenomenon is called specular reflection.
To avoid this, scan the bar code so that the beam does not bounce directly back. But do not scan at too oblique
an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode.
Practice quickly shows what tolerances to work within.
Side Views
No specular
reflection.
Decode can occur.
Specular reflection.
Reflected beam is
within specular dead
zone and prevents
decode.
°
30
Ba
ode
rC
rC
Ba
e
od
Tilt Bar Code At Slight Angle (Up to 30°)
Figure 1-4 Avoiding Specular Reflection
When scanning a 1D bar code, there is only a small specular dead zone to avoid (+ 2o from the direct laser
beam). However, the scanner is not effective if its beams hit the bar code surface at an angle greater than 30o.
1-8
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Imaging with the MK4000
When imaging, ensure the bar code is within the decode range and within the aiming pattern. The MK4000
beeps to indicate a successful decode.
Place the symbol in any orientation within the aiming pattern. Ensure the entire symbol is within the rectangular
area formed by the brackets in the aiming pattern. The red laser aiming pattern turns on to assist in aiming.
1D bar code symbol
2D bar code symbol
Figure 1-5 Imager Aiming Pattern: Bar Code Centered
Correct
Incorrect
Figure 1-6 Imager Aiming Pattern: Bar Code Not Centered
CHAPTER 2 INSTALLATION
Overview
This chapter describes MK4000 installation, including:
• Unpacking
• Mounting
• Inserting a micro SD card
• Providing power
• Connecting to a host
• Connecting peripherals
• Mounting the MK4000
• Magstripe reader installation
• Adding an advertising insert.
Unpacking the MK4000
Remove the MK4000 from its packing and inspect it for damage. Keep the packing, it is the approved shipping
container and should be used if the MK4000 needs to be returned for servicing.
2-2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Removing the Screen Protector
A screen protector is applied to the MK4000. Zebra recommends using this to minimize wear and tear. Screen
protectors enhance the usability and durability of touch screen displays.
To remove the screen protector, lift the corner using a thin plastic card, such as a credit card, then carefully lift
it off the display.
CAUTION
Do not use a sharp object to remove the protector. Doing so can damage the display.
For a package of five replacement screen protectors, contract Zebra.
Inserting a Micro SD Card
To use a micro SD card, insert it into the slot in the back of the MK4000 as shown on the device. See Figure
1-2 on page 1-3 for slot location. To remove the card, press down gently on it to eject, then remove it from the
slot.
Connecting the MK4000
The MK4000 communication interfaces include both wired or wireless solutions:
• USB Connection
• Mini USB 1.1 host/client port - ActiveSync connection to a desktop computer
• Two Mini USB 1.1 host ports for peripheral connections
• Wired Ethernet (10/100Base-T cable)
• Power through AC outlet
• Power through POE
To access the Windows® CE Desktop, see Accessing the Windows® CE Desktop on page 4-2.
AC Power Supply
The universal AC power supply connects to the power port on the MK4000 using a 2.0 mm barrel jack. The
power supply has a positive center pin and the outer tab is ground. It is compatible with:
• 120V 60 Hz (North America)
• 230V 50 Hz (International excluding Japan)
• 100V 50/60 Hz (Japan).
Installation
2-3
USB Connection
Connecting to a Host
The MK4000 can communicate with a host using a mini B USB cable connected to the mini USB port.
1.
Insert the power supply barrel connector into the MK4000 power port. See Figure 1-2 on page 1-3.
2.
Route the power cable.
3.
Plug the AC power supply into a wall outlet.
4.
Connect the USB cable to the mini USB port on the MK4000. See Figure 1-2 on page 1-3 for port
locations.
5.
Connect the other end of the cable to a USB port on the host.
Connecting to Peripheral Devices
Use a mini A USB cable and a USB adapter cable (available from Zebra) to connect to a peripheral device
such as a printer, a handheld scanner, a keyboard, or mouse.
1.
Connect the mini A USB cable to the mini USB port on the MK4000. See Figure 1-2 on page 1-3 for port
locations.
2.
If necessary, connect the USB adapter cable to the mini A USB cable.
3.
Connect the other end of the cable to the peripheral device.
Wired Ethernet Connection
Wired Ethernet: Power through AC Outlet
The MK4000 communicates to the host through a 10/100Base-T Ethernet cable and receives power through a
AC power supply.
1.
Insert the power supply barrel connector into the MK4000 power port. See Figure 1-2 on page 1-3.
2.
Route the power cable.
3.
Plug the AC power supply into a wall outlet.
4.
Connect the Ethernet cable to the RJ45 port on the MK4000. See Figure 1-2 on page 1-3.
5.
Plug the other end of the Ethernet cable into the host system LAN port.
Wired Ethernet: Power through POE
The POE installation option allows the MK4000 to communicate and receive power on the same 10/100Base-T
Ethernet cable.
1.
Connect the Ethernet cable to the MK4000 RJ45 port. See Figure 1-2 on page 1-3.
2.
Plug the other end of the Ethernet cable into an 802.3at certified host system LAN port or 802.3at port
injector.
2-4
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
RJ45/Ethernet Connector Pinouts
Figure 2-1 identifies the locations for the Ethernet port pins, and Table 2-1 lists pin descriptions.
Pin 8
Pin 1
Figure 2-1 8-Pin RJ45 Connector Port
Table 2-1 RJ45/Ethernet Pin Descriptions
Pin
Description
1
TXD (+)
2
TXD (-)
3
RXD (+)
4
Bias-T VCC
5
Bias-T VCC
6
RXD (-)
7
Bias-T GND
8
Bias-T GND
Installation
2-5
MK4000 Mounting
To mount the MK4000 on a wall or counter top, use a mounting bracket that conforms to the 100 mm VESA
specification. Also, Zebra offers an optional wall mount kit and pole mount kit for mounting the MK4000.
Using a VESA Mount
To mount the MK4000 using a 100 mm VESA mounting bracket:
1.
The device’s mounting inserts are M4 x 8.1 mm. When selecting an appropriate screw type, ensure its
length does not penetrate the device’s back housing more than 8.1 mm after going through the mounting
plate.
2.
Align the VESA mounting holes with the mounting holes on the back of the device.
3.
Insert the screws through each of the four aligned mounting holes.
Figure 2-2 provides MK4000 dimensions for mounting reference.
Note: Dimensions are in mm. To convert to inches, divide by 25.4.
Figure 2-2 MK4000 Mounting Dimensions
2-6
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Using the MK4000 Wall Mount Kit
To mount the MK4000 using the Wall Mount Kit:
1.
Determine the MK4000 mounting location.
2.
Secure the mounting plate to the wall using the four wood screws provided.
3.
Insert the four shoulder screws, also provided, into the mounting holes in the back of the MK4000.
Shoulder Screws (4)
Wood Screws (4)
Figure 2-3 MK400 Wall Mounting
4.
Connect the cables to the MK4000 and route and secure them properly.
5.
Mount the MK4000 by placing the shoulder screws through the four keyholes on the mounting plate, and
slide the MK4000 down to secure in place.
Installation
6.
2-7
Insert the locking screw through the hole in the tab at the side of the mounting plate. Hand tighten the
screw to secure the MK4000.
Locking Screw
Figure 2-4 MK4000 Wall Mount Locking Screw
Using the MK4000 Pole Mount Kit
To mount the MK4000 to a pole using the Pole Mount Kit:
1.
Connect the cables to the MK4000 and route and secure them properly.
2.
Secure the mounting plate to the MK4000 using the four M4 panhead screws provided.
3.
Insert the four shoulder screws into the mounting bracket.
4.
Route the pole mount straps through the mounting bracket. Wrap them around the pole and tighten.
5.
Mount the MK4000 by placing the four keyholes on the mounting plate over the shoulder screws on the
mounting bracket, and slide the MK4000 down to secure in place.
2-8
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
6.
Insert the locking screw through the hole in the bottom tab on the mounting bracket. Hand tighten the
screw to secure the MK4000.
Mounting Plate
Panhead Screws (4)
Mounting Bracket
Locking Screw
Shoulder Screws (4)
Figure 2-5 MK4000 Pole Mount Installation
Pole Mount Straps
Figure 2-6 MK4000 Pole Mount
Installation
Magstripe Reader Installation
To install the optional MSR:
1.
Secure the mounting plate to the MK4000 using the four screws provided.
Figure 2-7 Securing the MSR Mounting Plate
2-9
2 - 10 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
2.
Secure the MSR to the plate using the two screws provided.
Figure 2-8 Securing the MSR to the Mounting Plate
3.
Connect the USB cable to one of the two mini USB host ports.
Figure 2-9 Connecting the USB Cable
Installation 2 - 11
Card Swiping
Swipe a card through the MSR in either direction, with the magnetic stripe facing in toward the MK4000.
Figure 2-10 Card Swiping
2 - 12 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Advertisement Insert Mounting
Use an advertisement insert to attract customers to the MK4000. The recommended material for this is
corrugated polyethylene. The internal dimensions of the insert must be 8.90 (226 mm) wide x 0.26” (6.5 mm)
thick.
To install an insert:
1.
Secure each of the two advertisement insert brackets to the back of the MK4000 using two of the provided
pan head screws.
Sign Mount Bracket
Figure 2-11 Securing Sign Mount Brackets
2.
Slide the insert into the bracket grooves on either side of the MK4000, and mount ads, signs, or
instructions on this as needed.
NOTE
The optional MSR attachment accommodates signs so only one bracket is necessary.
Installation 2 - 13
10.13” / 257 mm
0.26” / 6.50 mm
(thickness)
8.90” / 226 mm
11.82” / 300 mm
Figure 2-12 Advertisement Insert Dimensions
2 - 14 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
CHAPTER 3 CONFIGURATION
Overview
This chapter describes how to set up and configure the MK4000 applications, communications, and network
settings which include parameters such as the device name, internet browser settings, date and time, and
several other key settings.
Configure these settings remotely using the System Configuration Manager (SCM), or locally on the MK4000
using the Control Panel. These settings are saved in the configuration registry file (mkconfig.reg) in the
MK4000 Application folder to maintain them across cold boot cycles. For information on using the Control
Panel, refer to the Microsoft Applications for Mobile and Win CE 5.0 User Guide.
System Configuration Manager
The System Configuration Manager (SCM) is a Windows®-based utility that runs on a host computer and
creates/edits an MK4000 configuration file (mkconfig.reg). Load this file onto the MK4000 and reboot the
MK4000 to set configuration parameters for the device. The configurable options for the MK4000 are defined in
an XML file that is available from Support Central at http://www.zebra.com/support.
. SCM is also available at Support Central.
SCM eliminates the potential user errors that occur when manually editing registry settings.
File Types
SCM uses three types of files:
• Symbol Configuration Template (.SCT) files are XML files that define the configurable parameters for a
device.
• Registry Configuration Service Provider XML files for device provisioning.
• CAB Provisioning Format (.CPF) file which is a .CAB archive that contains the provisioning XML. This file
is downloaded to the MK4000 and merged upon a cold boot.
3-2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
User Interface
SCM's user interface consists of a tree control on the left side of the window which displays all the
configuration categories, and a data grid table on the right which displays all the configurable controls for the
selected category. Figure 3-1 shows the main window for a device’s .sct file.
Figure 3-1 Main SCM Window
Menu Functions
Use the main menu to access the program functionality described in Table 3-1.
Table 3-1 SCM Menu Functions
Menu Item
Description
File Menu
Open Config File
Open a saved configuration file (.SCD).
Save Config Changes
Save changes to the currently loaded configuration file.
Restore All Defaults
Restore all parameter values to the default state. The default values are stored in
a Symbol Configuration template file.
Export Changes to .xml
Export the changed parameter values to an XML file.
Export Changes to .cpf
Export the changed parameter values to an CPF file.
Export all to .xml
Export all the parameter values to an XML file.
Export all to .cpf
Export all the parameter values to an CPF file.
Exit
Exit System Configuration Manager.
Configuration
3-3
Table 3-1 SCM Menu Functions (Continued)
Menu Item
Description
Device Menu
Device type
Change the current device type template. Each template (available from Support
Central) must reside in the SCM directory.
Help Menu
Display the About dialog which shows the application version.
About
Parameter State Indicators
The first column of the data table displays parameter state indicators. The state indicators display one of the
states in Table 3-2 for a particular parameter:
Table 3-2 Parameter Status Indicators
Icon
Indicator
Description
Modified
This parameter was changed from its initial factory setting.
Invalid
This parameter is not valid for the selected device type. This can occur when a
configuration file for one type of device is loaded and the device type is changed
using the Device menu. Values marked “invalid” are not exported.
Window Status Bar
The SCM status bar on the bottom right corner of the window contains the items in Table 3-3 from left to right:
Table 3-3 Window Status Bar Items
Status Bar Item
Description
Invalid Count
Number of parameters not valid for the selected device.
Modified Count
Number of parameters modified from the factory defaults.
Device Type
Device type - version.
Figure 3-2 Sample Status Bar
The sample status bar in Figure 3-2 shows that the current configuration file contains 1 Invalid Parameter and
2 Modified Parameters.
3-4
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
File Deployment
Deploy the CPF file created using the SCM export function to the MK4000.
1.
Optionally, use the Authenticode tools to sign the .cpf file.
2.
Make the .cpf file read-only, then copy it to the MK4000.
3.
Tap the filename to install.
4.
Certain applications and settings require a cold boot to take affect. In these cases, cold boot the MK4000.
Refer to the Windows Mobile Version 5.0 Help file for more information.
For more information on file deployment, see Deployment on page 5-4.
Local Configuration Using the Microsoft Windows Control Panel
Use the Control Panel on the MK4000 Start menu to change settings locally. For information on using the
Control Panel, refer to the Application Guide for Devices.
Configuration via Registry File
Before downloading the configuration file (.reg file) to the MK4000 Application folder, rename it mkconfig.reg.
Use one of the following methods to download the file to the MK4000:
• Copy the mkconfig.reg file to the MK4000 Application folder using a USB ActiveSync connection (see
Downloading Files to the MK4000 on page 5-6).
• Send the file to the MK4000 Application folder using FTP (see the instructions provided with the FTP
software) or AirBeam.
• Copy the mkconfig.reg file to an SD card, then transfer the file into the MK4000 Application folder.
Rebooting the MK4000
After downloading the mkconfig.reg file, cold boot the MK4000 to apply the new settings.
Cold Boot
Press and hold reset button on the side of the MK4000 for 10 seconds, then release, OR remove and apply
power.
Warm Boot
Run the Warmboot application. Select Start > Programs > Warmboot. Alternatively, use the Application
Program Interface (API).
CHAPTER 4 SYSTEM FEATURES
Overview
This chapter discusses the following operating system features:
• RegMerge and CopyFiles on page 4-2
• Accessing the Windows® CE Desktop on page 4-2
• Network Time Update: SNTP Client on page 4-2
• Memory Management on page 4-2
• Loading Additional Fonts on the MK4000 on page 4-3
• Input Panel (Virtual Keyboard) on page 4-5
• Microsoft Applications on page 4-5
4-2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
RegMerge and CopyFiles
RegMerge and CopyFiles are two device drivers included in the Windows CE OS to assist developers in
configuring the MK4000 following a cold boot. See Flash Storage on page 5-18 for more information.
Accessing the Windows® CE Desktop
If an MK4000 is configured to launch an application on power-up, you can bypass the application at boot-up to
access to the Windows® CE desktop.
Network Time Update: SNTP Client
The MK4000 Simple Network Time Protocol (SNTP) client can automatically set and update the MK4000 time
and date through the network. Use this feature to set the system time and date after reboots or power outages.
This feature also ensures consistent time and date stamping across a fleet of MK4000s. The SNTP Client
program queries the specified SNTP server over the network to set the time and date.
The SNTP client shipped with MK4000 WinCE 4.20 is the Microsoft default SNTP Client program. (This is a
change from the WinCE 4.1 operating system, which had a custom SNTP client).
Memory Management
Flash: Nonvolatile (Persistent) Memory
The MK4000 64 MB configuration has 64 MB of available nonvolatile flash memory. 5 MB is committed for
platform partition use to install external driver packs such as RF drivers, and 27 MB is available for developer’s
applications within the application partition (folder). The data partition (folder) has no available memory. The
data stored in flash memory persists through cold boot cycles.
To increase usable persistent (flash) memory, use the Terminal Configuration Manager (TCM) to adjust the
allocation of memory between the application and data partitions. See Chapter 5, Application Deployment.
Add a PC card to the MK4000 to increase the non-volatile memory available for file storage.
RAM: Volatile (Non-Persistent) Memory
The MK4000 has 128 MB of DRAM volatile memory. Developers can automate control of the device’s RAM
(volatile) memory allocation (storage vs. memory used to run programs) to persist memory allocation settings
through cold boot cycles.
System Features
4-3
Browser Applications
The PocketBrowser 2.1 development tool allows Web developers to quickly create robust applications that can
include a wide range of advanced data capture capabilities. The PocketBrowser 2.1 Developer Help provides
information on using each feature of the browser. Each feature includes a sample, however the sample does
not necessarily show the only way to implement each feature.
PocketBrowser extends the core rendering engine functionality of Microsoft PocketIE or Microsoft IE with
Zebra application programming interfaces (APIs). It provides interfaces to device hardware and features using
meta tags and Microsoft ActiveX® components designed specifically for Zebra systems. PocketBrowser offers
easy integration with bar code scanners, RFID readers, and other peripherals such as printers and magnetic
stripe readers (MSR) for complete transaction processing.
Loading Additional Fonts on the MK4000
You can program the MK4000 to support additional fonts such as Unicode and double-byte character font.
The MK4000 supports the following system fonts as shipped from the factory. The font files corresponding to
these formats are located in the \windows folder with .ttf extension.
• Arial
• Comic Sans MS
• Courier New
• Georgia
• Symbol
• Tahoma
• Times New Roman
• Verdana
• Wingding.
The default system font path for these fonts is \windows.
Use one of the following options to load fonts not supplied with the MK4000:
• Change the system font path where the system looks for fonts. For example, to change default system
font path from \windows to \application\fonts add the following registry to the system along with new fonts
in \application\fonts:
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\FontPath]
"FontPath"="\application\fonts"
Adding this registry changes the entire system fonts directory, so fonts supplied with the OS are no
longer available. To use both the provided system fonts and new fonts, copy the system default fonts to
the new font directory.
• Copy new/alternate fonts to the default \windows directory.
• Copy alternate fonts to the \windows\fonts directory.
Copying new fonts to the \windows or \windows\fonts preserves existing fonts. However the new fonts
consume system RAM as they are part of the ObjectStore.
4-4
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Using the third option, i.e., copying fonts to the \windows\fonts directory, makes it easier to manage the system.
Note that fonts copied to \windows or \windows\fonts do not persist over power cycles or cold boots. Use the
copy file feature to persist them over power cycles or cold boots.
Using Additional Fonts in Native Applications
Any application written in EVC can use the additional fonts using either MFC or Win32 APIs. If a specified font
is missing, the system uses an available font for display.
Using Additional Fonts in Managed Applications
All fonts installed in the system are available to the .Net Compact Framework during runtime.
Using Additional Fonts in Browser Applications
Regardless of how you installed the font in the system, to reference it using a browser page, specify the font as
a STYLE, or use FONT tags. Use intuitive names for the fonts (use FontViewer on a Windows desktop and
locate the Typeface Name line), and use quotes to enclose names with spaces. If the specified font is missing,
Internet Explorer uses its default font to display the text.
Things to Consider when Using Additional Fonts
• Different font styles (e.g., bold and italic) often require separate TTF files; be sure to provide all required
styles. Do not reference styles by name (e.g., Arial Bold); set the style separately from the font (e.g.,
using a “b” or “strong” tag, or a style).
• For best results, do not direct the system font path to a storage card (PCMCIA), as this can negatively
impact system performance. If this method is necessary, test the use of a storage card thoroughly for
fonts to ensure proper operation.
• Most Web pages contain information that tells the browser what language encoding (the language and
character set) to use. If the page does not include that information, and the Language Encoding
Auto-Select feature is on, Internet Explorer can usually determine the appropriate language encoding. If
not, manually select it using View menu > Encoding > More, then select the appropriate language.
NOTE
If the Auto-Select feature or a specific language pack is not installed, Internet Explorer prompts you to
download the files. Adding languages does not guarantee Web pages display in the preferred language.
System Features
4-5
Input Panel (Virtual Keyboard)
Use the input panel (virtual keyboard) on the touchscreen of the MK4000 to enter information.
To access the Input Panel, tap the
icon in the icon tray. To enter information, use a stylus to select the keys
on the input panel. To close the Input Panel, double-tap the icon.
Figure 4-1 Input Panel (Virtual Keyboard)
NOTE
Use Ctrl-C to copy text, and Ctrl-V to paste text.
Microsoft Applications
The MK4000 includes Microsoft WordPad, Windows Media Player, and Internet Explorer. For information on
using these applications, refer to the Microsoft Applications for Mobile and Win CE 5.0 User Guide
4-6
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
CHAPTER 5 APPLICATION DEPLOYMENT
Overview
To develop applications to run on the MK4000, use one or all of the following:
• Enterprise Mobility Developer Kit (EMDK) for C for developing native C/C++ applications
• Enterprise Mobility Developer Kit (EMDK) for .Net for developing managed .NET applications
• PocketBrowser for support for web development
• Device Configuration Package (DCP) for MK4000.
Enterprise Mobility Developer Kit (EMDK) for C
The Enterprise Mobility Developer Kit for C is based on industry-standard Microsoft® Windows® CE
development tools and enables development of native C and C++ applications. Use this developer kit in
conjunction with Microsoft® Embedded Visual C++ 4.0 Service Pack 3 and MK4000 Platform Software
Development Kit (PSDK).
EMDK for C includes the following components:
• Standard C API Libraries
• MK4000-specific C API Libraries
• Help file containing a C API Reference Guide
• Sample applications with full source code.
5-2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Sample Applications
The sample applications are included as a learning tool, to show developers how to interface with the C API
functions. Some of the sample applications contained in the kit include:
• Hello: A simple Hello World application.
• DisplayTest: Displays various colors on the LCD screen.
• KeyCheck: A keyboard checking utility that displays the keys pressed on the device and their associated
WM_MESSAGE.
• ScanSamp2: Demonstrates the bar code scan engine (and external scanner).
• MSRSamp2: Displays the MSR track data when a card is swiped.
• MemTest: Displays the amount of available memory. Allocate and free blocks of memory to see how
available memory changes.
• Win32PrintSamp: Prints a sample page to a connected printer.
NOTE
The MK4000 supports the Signature Capture API via the EMDK for C only. Refer to the Enterprise Mobility
Developer Kit version 1.4 or later, under MK Series C APIs - Signature Capture.
Enterprise Mobility Developer Kit (EMDK) for .NET
The Enterprise Mobility Developer Kit for .NET allows Microsoft® .NET Compact Framework developers to
create managed (C# and VisualBasic.NET) applications that harness value-add features on the MK4000. Use
this developer kit in conjunction with the EMDK for C.
The EMDK for .NET includes the following components:
• Class libraries
• Sample applications
• Documentation describing how to use the methods for each class library
Application Deployment
5-3
PocketBrowser for the Web
PocketBrowser is a web development kit that provides access to the functionalities of a Zebra device.
PocketBrowser is used across all vertical markets and in a wide variety of applications, enabling developers
and integrators to provide advanced Web-based solutions for Zebra devices. Transfer a PocketBrowser
application from one Zebra device to another seamlessly without recompiling or rewriting it.
PocketBrowser features include:
• Blocking users from the Microsoft operating system
• Exposing the full screen area to the Web application designer
• Seamless integration with bar code scanning
• Wireless connectivity
• Magnetic stripe readers.
Device Configuration Package
Use the Device Configuration Package (DCP) to create and download hex images that represent flash
partitions to the MK4000. The DCP includes the user documentation, flash partitions, Terminal Configuration
Manager (TCM), and the associated TCM scripts.
To install the DCP for the MK4000:
1.
Download the DCP from the Support Central web site, http://www.zebra.com/support
a.
On http://www.zebra.com/support, select Software Downloads.
b.
Select MicroKiosks and then select MK4000.
c.
Select the Device Configuration Package (DCP).
d.
Save the .exe file to the development computer.
2.
Locate the .exe file on the development computer, double-click the file, and follow the install screen
prompts.
3.
Once installed, access the major components of the DCP from the Device Configuration Package (DCP)
for MK4000 program group of the Windows Start Menu.
Platform SDK
To download and install the Platform SDK:
1.
2.
Download the appropriate Platform SDK from the Support Central web site, http://www.zebra.com/support
a.
On http://www.zebra.com/support, select Software Downloads.
b.
Select MicroKiosks and then select MK4000.
c.
Select the Platform SDK.
d.
Save the .exe file to the development computer.
Run the file and follow the screen prompts to install.
Installing Enterprise Mobility Developer Kits
To install an EMDK:
5-4
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
1.
2.
Download the EMDK from http://www.zebra.com/support
a.
On http://www.zebra.com/support, select Developer Downloads and sign in.
b.
Select MicroKiosks and then select MK4000.
c.
Select the latest version of the Enterprise Mobility Developer Kit.
d.
Download the .exe file to the development computer.
Double-click the executable file and follow the install screen prompts.
Installing Other Development Software
Developing applications for the MK4000 may require installing other development software such as application
development environments on the development PC. Follow the installation instructions provided with this
software.
Deployment
With the appropriate accessory, software, and connection, the MK4000 can share information with the host
device. This chapter provides information about installing software and files on the MK4000.
Download and install software using one of the following methods:
• ActiveSync (see page 5-5)
• OS Update (via SD card) (see page 5-7)
• Terminal Configuration Manager (TCM) (see page 5-8)
• FTP server using Rapid Deployment (see page 5-17)
• AirBEAM (see page 5-17).
Application Deployment
5-5
ActiveSync
The MK4000 communicates with a host computer using Microsoft® ActiveSync (version 4.5.1 or higher). Use
USB ActiveSync to transfer data between a host computer and the MK4000. The ActiveSync software on the
MK4000 allows copying and pasting (rather than synchronizing) files between the MK4000 and host computer.
Installing ActiveSync
To install ActiveSync on the host computer, download the latest version of the software from
http://www.microsoft.com. Refer to the installation instructions included with the ActiveSync software.
Connecting the MK4000 to the Host Computer
To configure ActiveSync for Guest access (suitable for copying files between the host computer and the
MK4000):
1.
Connect the USB cable to the mini USB port on the MK4000 (see Figure 1-2 on page 1-3). Connect the
other end of the cable to a USB port on the host computer.
2.
If the New Partnership window does not appear, on the host computer, select Start > Programs > Microsoft
ActiveSync.
Figure 5-1 New Partnership Window
3.
Click No and then Next. The Microsoft ActiveSync Guest Connected window displays.
Figure 5-2 Microsoft ActiveSync Guest Connected Window
5-6
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Downloading Files to the MK4000
To download files (such as the mkconfig.reg file) from the host computer to the MK4000, use Windows
Explorer to copy the files:
1.
On the host computer, select Explore.
Figure 5-3 ActiveSync Explorer
2.
Double-click the folder to expand the contents of the folder.
Figure 5-4 My Pocket PC Contents
3.
Use Explorer to locate the host computer directory that contains the file to download. Tap that directory in
the left pane to display its contents in the right pane.
Application Deployment
4.
5-7
Drag the desired file(s) from the host computer to the desired mobile device folder.
• Program Files folder: files stored in this folder are discarded after a cold boot.
• Application folder: files stored in this folder are retained after a cold boot.
NOTE
Cold booting the MK4000 erases all files in RAM. Be sure to save any critical files in the Application folder,
e.g., radio profile, time zone setting, license keys. See Downloading Files to the MK4000 on page 5-6.
OS Update
To upgrade the operating system using an SD card,
1.
Install the DCP onto the desktop computer.
NOTE
If you use a firewall, the firewall may prevent some files from installing. To verify that the DCP installation
completes, ensure the following folder contains files, and is not empty:
<Your drive:>\Program Files\Symbol Device Configuration Package\MK4000c50\<version number folder>
\OSUpdate\Images.
2.
Insert an SD card with at least 16 MB of storage into the MK4000. See the Inserting a Micro SD Card on
page 2-2.
3.
Connect the MK4000 to power and to the desktop computer via a USB cable, and set up a partnership
between the two computers using ActiveSync. See ActiveSync on page 5-5.
4.
In the ActiveSync window on the desktop computer, select Explore.
5.
On the drive in which you installed the DCP (typically C:), navigate to the directory:
\Program Files\Symbol Device Configuration Packages\MK4000c50\V1.0\
6.
Copy the OSUpdate folder into the My Device\SC Card\ folder on the MK4000.
7.
On the MK4000, tap Start > Programs > Windows Explorer.
8.
Navigate to \SD Card\OSUpdate folder.
9.
Double-tap the MK4000c50BenColor_SD.LNK file.
10. After the update completes and the MK4000 reboots, remove the SD card.
5-8
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Terminal Configuration Manager (TCM)
Terminal Configuration Manager (TCM) is an application that runs on the host computer and customizes flash
file system partitions for the MK4000. The most common use is to create an application partition hex file that
contains the customer's application. Also use TCM to load hex files to the flash memory of the MK4000.
TCM scripts control the customization of partitions. The scripts contain all the information for building an image.
The script is a list of copy commands specifying the files to copy from the development computer to the
partition.
TCM works with a pair of directory windows, one displaying the script and the other displaying the source files
on the development computer. Use standard Windows drag-and-drop operations to add and delete files from
the script window.
The DCP for MK4000 includes scripts Zebra uses to build the standard factory-installed Platform and
Application partitions on the MK4000. The standard Platform partition contains drivers and the Application
partition contains demo applications and optional components. The standard TCM scripts are in the following
folder:
C:\Program Files\Symbol Device Configuration Packages\MK4000 v1.0\TCM Scripts.
NOTE
Before creating a script to build a hex image, identify the files required (system files, drivers, applications,
etc.) and locate the files’ source directories to ease the script building process.
The processes for building a hex image in TCM include:
• Starting TCM
• Defining script properties
• Creating the script for the hex image
• Building the image
• Download the hex image to the MK4000
• Creating a splash screen
• Flash storage.
PC Download
Use the developer cable (p/n 25-119283-01R) with TCM to download hex configuration files to the MK4000, to
download customized flash file system partitions to the MK4000, and load hex files to the flash memory of
device.
A typical partition is a group of files, combined into a single “partition” that represents a specific area of storage.
Examples of partitions are the flash file systems such as Platform or Application. (Using the desktop computer
comparison, these partitions are roughly equivalent to a C: or D: hard disk drive.) In addition to the “hard disk”
partitions, some partitions are used for single items such as the operating system, monitor, or splash screen.
(Again using a desktop computer comparison, these partitions are roughly the equivalent of the BIOS or
special hidden system files.) Updating a partition erases all data previously in its storage region, i.e., it is not a
merge but a replacement operation.
Application Deployment
5-9
Starting TCM
Click the Windows start menu TCM icon (Device Configuration Packages, MK4000) to start TCM. The TCM
window displays two child windows: Script1 and File Explorer. The Script1 window contains a new script and
the File Explorer window contains a file explorer view for selecting files to place in the script.
Figure 5-5 TCM Startup Window
Table 5-1 lists the components of the TCM window.
Table 5-1 TCM Components
Icon
Component
Function
Script Window
Displays the files to use in creating the partition(s).
File Explorer Window
Lists the files to add to the script.
Create button
Creates a new script file.
Open button
Opens an existing script file.
Save button
Saves the current script file.
Large icons button
Views the current script items as large icon.
Small icons button
Views the current script items as small icon.
List button
Views the current script items as a list.
Details button
Views the current script items with more details.
5 - 10 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Table 5-1 TCM Components (Continued)
Icon
Component
Function
About button
Displays version information for TCM.
Properties button
Views/changes the current script properties.
Build button
Builds the current script into a set of hex files.
Check button
Checks the script for errors (files not found).
Send button
Downloads the hex image to the vehicle computer.
Tile button
Arranges the sub-windows in a tiled orientation.
Build and Send
Builds the current script into a set of hex images and sends the hex
images to the device.
Preferences button
Views/changes global TCM options.
Defining Script Properties
Before creating a script, define the script properties, such as the type of device, flash type, number of disks
being created, and the memory configuration of each disk partition.
To define the script properties:
1.
Select the Script window to make it active.
2.
Click the Properties button. The Script Properties window > Partition Data tab appears.
Figure 5-6 Script Properties Window - Partition Data Tab
3.
In the Terminal drop-down list, select the terminal type.
4.
Use the default Flash Type.
5.
In the Disks drop-down list, select the number of disk partitions to create.
6.
Select the (memory) Size for each partition. Note that adding space to one disk partition subtracts it from
another.
Application Deployment 5 - 11
7.
In the Access drop-down list for each disk partition, determine and select the Read/Write access option.
8.
Click the Options tab. The Script Properties window Options tab appears.
Figure 5-7 Script Properties Window - Options Tab
9.
Set the paths for the Script File, Flash File, and Hex File Build.
10. Click OK.
Creating the Script for the Hex Image
On start-up, TCM displays the TCM window with the Script1 window and File Explorer window pointing to the
following directory:
\Program Files\Symbol Device Configuration Packages\MK4000\TCMScripts\
The Script1 window directory pane displays two partitions: Platform and Application. Depending on the type of
flash chip, the number of partitions can change. You can add files to each of the partitions. TCM functionality
includes:
• Opening a new or existing script file
• Copying components to the script window
• Saving the script file.
Opening a New or Existing Script
You can create a script file from scratch or based on an existing script file. Click Create to create a new script
or click Open to open an existing script (for example, a script provided in the DCP for MC40x0c). If you open
an existing script and make changes, saving the changes overwrites the original script. To use an original or
Zebra supplied standard script as a base and save the changes in a new script, use the Save As function to
save the script using a different file name.
5 - 12 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Updating TCM 1.X Scripts
You can upgrade script files created with older versions of TCM to TCM 2.0 scripts. Click Open to open an
existing script created with an older version of TCM. The Conversion window appears.
Figure 5-8 Conversion Window - Upgrading to TCM 2.0
Copying Components to the Script
Script contents are managed using standard file operations such as New Folder, Delete and Rename. Items can
be added to the script by clicking files and folders in the File Explorer window and dragging them to the Script
window. The File Explorer window supports standard windows; multiple files may be selected by clicking while
holding the SHIFT or CTRL keys.
Saving the Script
Modifications to a script file can be saved using the Save or the Save As function. Saving changes to an existing
script writes over the original script. To use a Zebra-supplied standard script as a base and save the changes
in a new script, use the Save As function.
Building the Image
After creating the script, build the hex image defined by the script.
As part of the build, TCM performs a check on the script which verifies that all files referenced in the script
exist. This check is important for previously created scripts to ensure that files referenced in the script are still
in the designated locations.
To build scripts:
1.
Click Build on the TCM toolbar. The Configure Build window appears.
Figure 5-9 Configure Build Window
2.
Select the items (partitions) to build using the check box(es) to the left of each named partition.
3.
Use the Build Path to define where to store all built partitions.
Application Deployment 5 - 13
4.
Select (hex image) COMPRESSION to reduce the size and speed up the download.
5.
Click OK and follow the on-screen instructions.
If one of the partitions is the ESSID, a prompt appears requesting the ESSID value. Deselect the HR (High
Rate) check box when building ESSID images for a device with an FH radio.
Figure 5-10 Build ESSID Partition Window
If one of the partitions is the Splash Screen, a prompt appears requesting both the source Bitmap file and
the destination HEX file.
6.
TCM performs a check, and if there are no errors, creates the partition hex files.
If the build fails, TCM does not create the hex files and displays an error message. Two common reasons for a
build failure are:
• TCM could not find the files defined in the script. This error can occur when the files referenced by the
script are no longer stored on the development computer or the folders where they are stored were
renamed.
• The total amount of flash memory space that the script requires exceeds the image size. To correct this,
reduce the number of files in the partition or increase the size of the partition. See Defining Script
Properties on page 5-10 for more information about setting the image size appropriately.
Downloading the Image
After building the hex file, download it to the MK4000 using the developer cable:
1.
Remove power from MK4000.
2.
Connect a DB9 cable to the RJ45 port on the MK4000, and the other end to the host computer.
3.
Connect the developer cable to the mini USB host/client port (the mini USB port closest to the MicroSD
card slot) on the MK4000.
4.
Connect the other end of the developer cable to the USB port on the host computer.
5.
On the host computer open a terminal emulation program such as Hyperterminal. Configure the selected
port as follows:
• Baud rate: 38400
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
6.
Connect power to the MK4000. The download prompt }}} appears.
7.
Press the d key on the host computer. The prompt mon> appears.
5 - 14 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
8.
Enter the command:
d u: p=
then press the Enter key. The display indicates Waiting for input…
9.
In TCM on the host computer, click Load on the toolbar. The Load Terminal window > Serial tab appears.
Figure 5-11 Load Terminal Window - Serial and Ethernet Tabs
10. Select the Image Files To Load.
11. In the Comm Port drop-down list, select USB: Symbol Device.
12. Click Download to begin the operation. The Downloading screen on the MK4000 displays the Device Status
and a progress bar.
13. When complete, Device Status displays Result was: Success!, or in the case of an error, the cause of the
error.
14. When download completes, enter reset to reboot the MK4000.
Application Deployment 5 - 15
Calibrating the Screen
Use the Calibration screen to align the touch screen:
1.
Remove and restore power to the MK4000 to reboot.
Figure 5-12 Calibration Screen
NOTE
To access the Calibration screen from the Windows CE Control Panel, tap Start > Settings > Control
Panel. Double-tap the Stylus icon, tap the Calibration tab, and tap the Recalibrate button. The
Calibration screen appears.
2.
Carefully press and briefly hold the stylus tip on the center of the Calibration screen target. Repeat the
procedure as the target moves and stops at different locations on the screen.
3.
The Confirm Calibration screen displays. Tap the screen to accept the settings, or wait 30 seconds and the
MK4000 returns to the Calibration screen.
TCM Error Messages
TCM validates the cells in the partition table when you click the Execute button. Cells highlighted in red contain
an error. Partition loading is disabled until all errors are corrected.
Table 5-2 TCM Error Messages
Error
Description/Solution
Failed to build images: flash
file system DLL not loaded!
TCM could not load the DLL required to build images for the targeting flash file
system. Reinstall TCM or recover the DLL.
Failure finding directory xxx
Building process failed because directory xxx was not found.
Failure creating volume
Building process failed because a certain disk volume could not be created.
Failure adding system file to
image
Build process failed because TCM failed to add a certain system file to the
disk image.
INVALID PATH
The path for the image file to build is not valid.
Nothing Selected To Build
In the Config Build window, no item is selected to build.
Illegal ESS ID
In the Build ESSID Partition window, no ESS ID was entered or the ESS ID
entered was illegal.
5 - 16 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Table 5-2 TCM Error Messages (Continued)
Error
Description/Solution
Disk Full
TCM failed to create Hex image file at the selected path. Check available disk
space.
Target Disk Full
Build process failed because TCM failed to add file to the image of a disk
volume. Remove some files or increase the disk size.
Hex file is READ ONLY
The Hex image file to be created exists and is read-only. Delete the existing
file or change its attribute.
Error opening the file xxx with
write access
TCM could not open file xxx with write access. Check if file is in use.
Failure creating binary file
TCM failed to open/create an intermediate binary file.
Hex File To load is missing or
invalid
In Load Terminal window, the file selected to load has invalid status.
Could not locate MK4000
name in TCM.ini file
While loading the Script Properties window, TCM could not find the TCM.ini
section corresponding to the MK4000 type specified by the current opening
script. Either TCM.ini or the script file is invalid.
Incorrect disk sizes in TCM.ini
file
The total disk size specified in the script does not match the total disk size
defined in the corresponding TCM.ini section. Check if the script is corrupt or
the TCM.ini has changed after the script was created.
INVALID DIRECTORY
In Script Properties window, the selected System File Path is not a valid
directory.
One of the disk sizes is one
sector in size
In Script Properties window, one of the disks is too small (one sector in size).
This may cause problem while building images, especially when cushion is
enabled. Increase the disk size.
INVALID VOLUME NAME
In Script Properties window, one of the volume labels is not valid.
Corrupt TCM.INI file! (Invalid
value of VolumeDivisor)
The VolumeDivisor entry is missing or invalid in the TCM.ini. Reinstall TCM or
recover TCM.ini.
Invalid version of TCM script
file
The TCM script was not created by this version of TCM.
Corrupt or missing TCM.ini
file
TCM could not find TCM.ini file.
FAILED CONNECTION TO
COM PORT (Could not get
status)
While downloading images to MK4000, TCM failed to connect to the selected
COM port. Check if the COM port is free and is properly configured.
FAILED CONNECTION TO
TERMINAL (Terminal Not
Connected Properly/Terminal
Not Ready to Receive)
While downloading images, TCM failed to connect to the MK4000. Check if
the correct flow control protocol is selected and the MK4000 is properly
connected and is in a listening state.
Application Deployment 5 - 17
Creating a Splash Screen
The DCP for MK4000 includes the source bitmap files that create the default splash screens. You can
customize the screen by modifying these files using any of the standard windows image editors.
To create a custom splash screen:
1.
Use an image editor to open the Splashcolor.bmp file included with the DCP for MK4000.
2.
Modify the bitmap file and save.
3.
Create a splash partition. See Building the Image on page 5-12.
If you don’t use the default files to create the new splash screens, be sure to preserve the image format of 320
x 216, 8 bits per pixel. Note that 8 bits per pixel only applies to splash screen images. Once Windows CE is
running, the color density is 16 bits per pixel. See Downloading the Image on page 5-13 for information about
loading the splash screen using TCM.
Rapid Deployment Client
The Rapid Deployment (RD) Client facilitates software downloads to an MK4000 from a Mobility Services
Platform (MSP) Console’s FTP server. The MSP Console is a web-based interface to the wireless
infrastructure monitoring and management tools provided by the MSP Lite or MSP Enterprise server.
When software packages transfer to the FTP server, an MK4000 on the wireless network can download them
by scanning RD bar codes encoding the location of the software packages. Multiple MK4000s can scan a
single RD bar code.
NOTE
For detailed information about the Rapid Deployment Client and creating RD bar codes, refer to the MSP
3.X User’s Guide.
AirBEAM Smart
The AirBEAM Smart product transfers specially designed software packages between a host server and Zebra
wireless device. Before transfer, AirBEAM Smart checks and compares package version, so that only updated
packages load.
AirBEAM Smart resides on radio-equipped client devices and allows them to request, download, and install
software, as well as to upload files and status data. A single communications session can accomplish both
download and upload of files. The ability to transfer software over a radio network can greatly reduce the
logistical efforts of client software management.
In an AirBEAM Smart system, a network-accessible host server acts as the storage point for the software
transfer. The AirBEAM Smart Client uses the industry standard FTP or TFTP file transfer protocols to check the
host system for updates and, if necessary, to transfer updated software.
NOTE
For more information about AirBEAM Smart, refer to the AirBEAM® Smart Windows® CE Client Product
Reference Guide and AirBEAM Package Builder Product Reference Guide.
5 - 18 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Flash Storage
In addition to the RAM-based storage standard on Windows CE devices, the MK4000 also includes a
non-volatile Flash-based storage area which can store data (partitions) that a cold boot cannot corrupt. This
Flash area is divided into two sections: Flash File System (FFS) Partitions and Non-FFS Partitions.
FFS Partitions
The MK4000 includes two FFS partitions. These partitions appear to the MK4000 as a hard drive that the OS
file system can write files to and read files from. Data is retained even if power is removed.
The two FFS partitions appear as the following two separate folders in the Windows CE file system:
• Platform: The Platform FFS partition contains Zebra-supplied programs and Dynamic Link Libraries
(DLLs). This FFS is configured to include DLLs that control system operation. Since the MK4000 needs
these drivers for basic operation, only experienced users should modify the content of this partition.
• Application: The Application FFS partition stores application programs needed to operate the MK4000.
Working with FFS Partitions
Because the FFS partitions appear as folders under the Windows CE file system, you can read and write to
them like any other folder. For example, an application program can write data to a file located in the
Application folder just as it would to the Windows folder. However, the file in the Application folder is in
non-volatile storage and is not lost on a cold boot (e.g., when power is removed for a long period of time).
You can use standard tools such as ActiveSync to copy files to and from the FFS partitions. They appear as the
Application and Platform to the ActiveSync explorer. This is useful when installing applications on the MK4000.
Applications stored in the Application folder are retained even after a cold boot.
There are two device drivers included in the Windows CE image to assist developers in configuring the
MK4000 following a cold boot: RegMerge and CopyFiles.
RegMerge.dll
RegMerge.dll is a built-in driver that allows making registry edits to the Windows CE Registry. Regmerge.dll
runs very early in the boot process and looks for registry files (.reg files) in certain Flash File System folders
during a cold boot. It then merges the registry changes into the system registry located in RAM.
Since the registry is re-created on every cold boot from the default ROM image, the RegMerge driver is
necessary to make registry modifications persistent over cold boots.
RegMerge looks in the root of two specific folders for .reg files in the following order:
\Platform
\Application
Regmerge continues to look for .reg files in these folders until it checks all folders. This allows folders later in
the list to override folders earlier in the list. This way, it is possible to override Registry changes made by the
Platforms partitions folders. Take care when using Regmerge to make Registry changes. The DCP contains
examples of .reg files.
NOTE
Regmerge only merges the .reg files on cold boots. A warm boot skips the merge process.
Application Deployment 5 - 19
Typically, you would not modify the registry values for drivers loaded before RegMerge, although this may be
necessary during software development. Since these early loading drivers read these keys before RegMerge
can change them, you must cold boot the MK4000. The warm boot does not re-initialize the registry and the
early loading driver reads the new registry values.
Do not use Regmerge to modify built-in driver registry values, or merge the same Registry value to two files in
the same folder, as the results are not predictable.
CopyFiles
Windows CE expects certain files to be in the Windows folder, residing in volatile storage. Windows CE
maintains the System Registry in volatile storage. CopyFiles copies files from one folder to another on a cold
boot. Files can be copied from a non-volatile partition (Application or Platform) to the Windows or other volatile
partition during a cold boot. During a cold boot CopyFiles looks for files with a .CPY extension in the root of the
Platform, then the Application FFS partitions. These files are text files containing the source and destination for
the desired files to copy, separated by “>”. The demo application partition included in the DCP contains the
following example from the file application.cpy. Alternatively, obtain this from the Support Central web site at
http://www.zebra.com/support.
Files are copied to the Windows folder from the Flash File System using copy files (*.cpy) in the following
order:
\Platform
\Application
Example:
\Application\ScanSamp2.exe>\Windows\ScanSamp2.exe
This line directs CopyFiles to copy the ScanSamp2.exe application from the \Application folder to the
\Windows folder.
Non-FFS Partitions
Non-FFS Partitions include additional software and data pre-loaded on the MK4000 that you can upgrade.
Unlike FFS Partitions, these partitions are not visible when the operating system is running. They also contain
system information. Non-FFS partitions include the following:
• Windows CE: The complete Windows CE operating system is stored on Flash devices. If necessary, you
can download the entire OS image to the MK4000 using Zebra provided files. The TCM installation
package includes the current OS partition on the MK4000. Obtain any upgrades from Zebra. This
partition is mandatory for the MK4000.
• Splash Screen: a bitmap smaller than 16 kb (and limited to 8 bits per pixel) appears as the MK4000 cold
boots. To download a customized screen to display, see Creating a Splash Screen on page 5-17.
NOTE
8 bits per pixel only applies to splash screen images. Once Windows CE is running, the color density is
16 bits per pixel.
• Partition Table: Identifies where each partition is loaded in the MK4000.
Downloading Partitions to the MK4000
Use TCM to specify a hex destination file for each partition and download each file to the MK4000. This
download requires a program loader stored on the MK4000.
5 - 20 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
APPENDIX A TECHNICAL SPECIFICATIONS
Technical Specifications
For the latest technical specification information for the MK4000, visit: http://www.zebra.com/MK4000
A-2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
APPENDIX B WIRELESS CONFIGURATION
Overview
Use the MK4000’s Mobile Companion to configure the 11 Mbps wireless connection.
NOTE
Mobile Companion supports WPA Home, but not WPA Enterprise.
B-2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Wireless Applications
Wireless Local Area Networks (WLANs) allow MK4000s to communicate wirelessly and send data to a host
device in real time. Before using the MK4000 on a WLAN, the facility must be set up with the required
hardware to run the wireless LAN and you must configure the device. Refer to the documentation provided with
the access points (APs) for instructions on setting up the hardware.
To configure the MK4000, a set of wireless applications provide the tools to configure and test the wireless
radio in the device. The Wireless Application menu on the task tray provides the following wireless applications:
•
Find WLANs
•
Manage Profiles
•
Manage Certificates
•
Manage PACs
•
Options
•
Wireless Status
•
Wireless Diagnostics
•
Log On/Off
•
Enable/Disable Radio (Fusion 2.5 and above only).
Tap the Signal Strength icon to display the Wireless Applications menu.
Signal Strength Icon
Figure B-1 Wireless Applications Menu
Wireless Configuration
B-3
Signal Strength Icon
The Signal Strength icon in the task tray indicates the device’s wireless signal strength as follows:
Table B-1 Wireless Applications Icons, Signal Strength Descriptions
Icon
None
Status
Action
Excellent signal strength
Wireless LAN network is ready to use.
Very good signal strength
Wireless LAN network is ready to use.
Good signal strength
Wireless LAN network is ready to use.
Fair signal strength
Wireless LAN network is ready to use. Notify the network
administrator that the signal strength is only “Fair”.
Poor signal strength
Wireless LAN network is ready to use. Performance may not be
optimum. Notify the network administrator that the signal strength is
“Poor”.
Out-of-network range
(not associated)
No wireless LAN network connection. Notify the network
administrator.
No wireless LAN network
card detected.
No wireless LAN network card detected or radio disabled. Notify the
network administrator.
No wireless LAN network
card detected or Wireless
LAN disabled.
No wireless LAN network card detected or Wireless LAN disabled or
radio disabled. Notify the network administrator.
Turning the WLAN Radio On and Off
To turn the WLAN radio off tap the Signal Strength icon and select Disable Radio.
Figure B-2 Disable Radio
To turn the WLAN radio on tap the Signal Strength icon and select Enable Radio.
B-4
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Find WLANs Application
Use the Find WLANs application to discover available networks in the vicinity of the user and MK4000. To open
the Find WLANs application, tap the Signal Strength icon - Find WLANs. The Find WLANs window displays.
Figure B-3 Find WLANs Window
NOTE
Find WLAN display is limited to 32 items (ESSIDs or MAC addresses). A combination of up to 32 ESSIDs/APs
may be displayed.
Manually enter valid ESSIDs not displayed in the Find WLANs window. See Figure B-4 on page B-5.
The Find WLANs list displays:
•
WLAN Networks - Available wireless networks with icons that indicate signal strength and encryption
type. The signal strength and encryption icons are described in Table B-2 and Table B-3.
•
Network Type - Type of network.
•
Channel - Channel on which the AP is transmitting.
•
Signal Strength - The signal strength of the signal from the AP.
Table B-2 Signal Strength Icon
Icon
Description
Excellent signal
Very good signal
Good signal
Fair signal
Poor signal
Out of range or no signal
Table B-3 Encryption Icon
Icon
Description
No encryption. WLAN is an infrastructure network.
WLAN is an Ad-Hoc network.
WLAN access is encrypted and requires a password.
Wireless Configuration
B-5
Tap-and-hold on a WLAN network to open a pop-up menu which provides two options: Connect and Refresh.
Select Refresh to refresh the WLAN list. Select Connect to create a wireless profile from that network. This
starts the Profile Editor Wizard which allows you to set the values for the selected network. After editing the
profile, the device automatically connects to this new profile.
Profile Editor Wizard
Use the Profile Editor Wizard to create a new WLAN profile or edit an existing profile. If editing a profile, the
fields reflect the current settings for that profile. If creating a new profile, default values appear in the fields.
Navigate through the wizard using the Next and Back buttons. Tap X to quit. On the confirmation dialog box, tap
No to return to the wizard or tap Yes to quit and return to the Manage Profiles window. See Manage Profiles
Application on page B-28 for instructions on navigating the Profile Editor Wizard.
Profile ID
In the Profile ID dialog box in the Profile Editor Wizard, enter the profile name and the ESSID.
Figure B-4 Profile ID Dialog Box
Table B-4 Profile ID Fields
Field
Description
Profile Name
The name and (WLAN) identifier of the network connection. Enter a user friendly name
for the device profile used to connect to either an AP or another networked computer.
Example: The Public LAN.
ESSID
The ESSID is the 802.11 extended service set identifier. The ESSID is 32-character
(maximum) string identifying the WLAN, and must match the AP ESSID for the device to
communicate with the AP.
NOTE
Two profiles with the same user friendly name are acceptable but not recommended.
Tap Next. The Operating Mode dialog box displays.
B-6
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Operating Mode
Use the Operating Mode dialog box to select the operating mode (Infrastructure or Ad-Hoc) and the country
location.
Figure B-5 Operating Mode Dialog Box
Table B-5 Operating Mode Fields
Field
Operating Mode
Description
Select Infrastructure to enable the device to transmit and receive data with an AP.
Infrastructure is the default mode.
Select Ad Hoc to enable the device to form its own local network where devices
communicate peer-to-peer without APs using a shared ESSID.
Wireless Configuration
B-7
Table B-5 Operating Mode Fields (Continued)
Field
Country
Description
Country determines if the profile is valid for the country of operation. The profile country
must match the country in the options page or it must match the acquired country if
802.11d is enabled.
Single Country Use:
If using the device in a single country, set every profile country to Allow Any Country. In
the Options > Regulatory dialog box (see Figure B-41 on page B-44), select the specific
country in which the device is used, and deselect the Enable 802.11d option. This
common and efficient configuration eliminates the initialization overhead associated with
acquiring a country via 802.11d.
Multiple Country Use:
If using the device in more than one country, select Enable 802.11d in the Options >
Regulatory dialog box (see Figure B-41 on page B-44). This eliminates the need for
reprogramming the country (in Options > Regulatory) each time you enter a new country.
However, this only works if the infrastructure (i.e., APs) supports 802.11d (older firmware
versions on wireless infrastructures do not support 802.11d). When you select the
Enable 802.11d option, the Options > Regulatory > Country setting is not used for
infrastructure WLANs. 802.11d feature is only valid for Infrastructure WLANs. Ad-hoc
WLANs use the country options and must match the profile.
For a single profile to use in multiple countries, with infrastructure that supports 802.11d
(including infrastructure), set the Profile Country to Allow Any Country. Under Options >
Regulatory, select Enable 802.11d. The Options > Regulatory > Country setting is not
used.
For a single profile to use in multiple countries, but with infrastructure that does not
support 802.11d, set the profile country to Allow Any Country, and de-select (uncheck)
Enable 802.11d. In this case, always set the Options > Regulatory > Country setting to the
country the device is currently in. You can use this efficient configuration option with any
infrastructure. However, you must manually change the Options > Regulatory > Country
setting when entering a new country.
Note that using a single profile in multiple countries implies that there is a common
ESSID to connect to in each country. This is less likely than having unique ESSIDs in
each country, which requires unique profiles for each country.
For additional efficiency when using multiple profiles to use in multiple countries, set the
country setting for each profile to a specific country. If the current country (found via
802.11d or set by Options > Regulatory > Country when 802.11d is disabled) does not
match the country set in a given profile, that profile is disabled. This can speed profile
roaming. For example, if you create and configure two profiles for Japan, and two more
for USA, then when in Japan only the first two profiles are active, and when in USA only
the last two are active. If you configure them all for Allow Any Country, all four are always
active, making profile roaming less efficient.
Tap Next. If you selected Ad-Hoc mode, the Ad-Hoc Channel dialog box displays. If you selected Infrastructure
mode, the Security Mode dialog box displays. See Authentication on page B-10 for instruction on setting up
authentication.
B-8
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Ad-Hoc
Use the Ad-Hoc Channel dialog box to select the required information to create an Ad-Hoc profile. This dialog
box does not appear if you selected Infrastructure mode.
1.
Select a channel number from the Channel drop-down list.
Figure B-6 Ad-Hoc Channel Selection Dialog Box
NOTE
If in a country where DFS is implemented in band 5150-5250 MHz, you cannot use ad-hoc and must move and
select a channel in the 2.4 GHz band.
Ad-hoc channels are specific to the country selected.
Table B-6 Ad-Hoc Channels
Band
2.4 GHz
Channel
Frequency
1
2412 MHz
2
2417 MHz
3
2422 MHz
4
2427 MHz
5
2432 MHz
6
2437 MHz
7
2442 MHz
8
2447 MHz
9
2452 MHz
10
2457 MHz
11
2462 MHz
12
2467 MHz
13
2472 MHz
14
2484 MHz
Wireless Configuration
B-9
Table B-6 Ad-Hoc Channels
Band
5 GHz
Channel
Frequency
36
5180 MHz
40
5200 MHz
44
5220 MHz
48
5240 MHz
Tap Next. The Encryption dialog box displays. See Encryption on page B-19 for encryption options.
2.
Security Mode
Use the Security Mode dialog box to configure the Security and Authentication methods. If you selected
Ad-Hoc mode, this dialog box is not available and authentication is set to None by default.
Figure B-7 Security and Authentication Dialog Box
Select the security mode from the Security Mode drop-down list. This selection affects the availability of other
choices for Authentication Type and Encryption methods.
•
LEGACY (Pre-WPA) - This mode allows you to configure protocols not available in the other Security
Mode selections: Open authentication / encryption, Open authentication with WEP40 or WEP128, and
802.1X authentications that use WEP128 encryption.
•
WPA-Personal - This mode allows you to configure a WPA-TKIP-PSK protocol.
•
WPA2-Personal - This mode allows you to configure WPA2-PSK protocols with either the Advanced
Encryption Standard (AES) or TKIP encryption method.
•
WPA-Enterprise - This mode allows you to configure profiles with 802.1X Authentication that uses WPA
and TKIP encryption method.
•
WPA2-Enterprise - This mode allows you to configure profiles with 802.1X Authentication that uses
WPA2 with AES encryption method.
B - 10 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Table B-7 Security Modes
Security Mode
Authentication
Types
Encryption Types
Pass-phrase/Hexkey
Configuration
Legacy (Pre-WPA)
None, EAP-TLS,
EAP-FAST, PEAP,
LEAP, TTLS
Open,
WEP-40 (40/24),
WEP-104 (104/24),
TKIP, AES
Enabled. User input required with
pass-phrase/hex key configuration.
WPA - Personal
None
TKIP
Enabled. User input required with
pass-phrase/hex key configuration.
WPA2 - Personal
None
AES
Enabled. User input required with
pass-phrase/hex key configuration.
WPA - Enterprise
EAP-TLS, EAP-FAST,
PEAP, LEAP, TTLS
TKIP
Disabled. No user input required
for encryption key.
WPA2 - Enterprise
EAP-TLS, EAP-FAST,
PEAP, LEAP, TTLS
AES
Disabled. No user input required
for encryption key.
Authentication
Select an available authentication type from the drop-down list. The options listed are based on the selected
Security Mode as shown in Table B-7.
The authentication types, other than None, all use IEEE 802.1x authentication to ensure that only valid users
and sometimes servers can connect to the network. Each authentication type uses a different scheme using
various combinations of tunnels, username/passwords, user certificates, server certificates, and Protected
Access Credentials (PACs).
Table B-8 Authentication Options
Authentication
Description
None
Default setting when authentication is not required on the network.
EAP-TLS
Select this option to enable EAP-TLS authentication. A user certificate is required;
validating the server certificate is optional.
EAP-FAST
Select this option to enable EAP-FAST authentication. This type uses a PAC (Protected
Access Credential) to establish a tunnel and then uses the selected tunnel type to verify
credentials. PACs are handled behind the scenes, transparent to the user. Automatic PAC
provisioning can, depending on the tunnel type, require a user certificate and the
validation of a server certificate. Manual PAC provisioning is currently not supported.
PEAP
Select this option to enable PEAP authentication. This type establishes a tunnel and,
based on the tunnel type, uses a user certificate and/or a username/password.
Validating the server certificate is optional.
LEAP
Select this option to enable LEAP authentication. This type does not establish a tunnel.
It requires a username and password.
TTLS
Select this option to enable TTLS authentication. This type establishes a tunnel and,
based on the tunnel type, uses a user certificate and/or a username/password. Validating
the server certificate is optional.
Wireless Configuration B - 11
Tap Next. Selecting PEAP, TTLS, or EAP-FAST displays the Tunneled Authentication Type dialog box. Selecting
None displays the Encryption dialog box. Selecting EAP-TLS displays the Installed User Certs dialog box.
Selecting LEAP displays the User Name dialog box.
Tunneled Authentication
Use the Tunneled Authentication dialog box to select the tunneled authentication options. The content of the
dialog differs depending on the Authentication Type chosen.
Figure B-8 Tunneled Authentication Dialog Box
To select a tunneled authentication type:
1.
Select a tunneled authentication type from the drop-down list. See Table B-9 for the Tunnel authentication
options for each authentication type.
2.
Select the User Certificate check box if a certificate is required. If you selected the TLS tunnel type that
requires a user certificate, the check box is already selected.
3.
Tap Next. The Installed User Certificates dialog box appears.
Table B-9 Tunneled Authentication Options
Tunneled
Authentication
Authentication Type
PEAP
CHAP
EAP-GTC
MD5
TTLS
EAP-FAST
X
X
Challenge Handshake Authentication Protocol (CHAP)
is one of the two main authentication protocols used to
verify the user name and password for PPP Internet
connections. CHAP is more secure than PAP because it
performs a three way handshake during the initial link
establishment between the home and remote machines.
It can also repeat the authentication anytime after the
link is established.
X
X
Description
EAP-GTC is used during phase 2 of the authentication
process. This method uses a time-synchronized
hardware or software token generator, often in
conjunction with a user PIN, to create a one-time
password.
Message Digest-5 (MD5) is an authentication algorithm
developed by RSA. MD5 generates a 128-bit message
digest using a 128-bit key, IPSec truncates the message
digest to 96 bits.
B - 12 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Table B-9 Tunneled Authentication Options (Continued)
Tunneled
Authentication
Authentication Type
PEAP
MS CHAP
MS CHAP v2
EAP-FAST
X
X
PAP
TLS
TTLS
X
Microsoft Challenge Handshake Authentication Protocol
(MS CHAP) is an implementation of the CHAP protocol
that Microsoft created to authenticate remote Windows
workstations. MS CHAP is identical to CHAP, except that
MS CHAP is based on the encryption and hashing
algorithms used by Windows networks, and the MS
CHAP response to a challenge is in a format optimized
for compatibility with Windows operating systems.
X
X
X
Description
Microsoft Challenge Handshake Authentication Protocol
version 2 (MS CHAP v2) is a password-based,
challenge-response, mutual authentication protocol that
uses the industry-standard Message Digest 4 (MD4) and
Data Encryption Standard (DES) algorithms to encrypt
responses. The authenticating server challenges the
access client and the access client challenges the
authenticating server. If either challenge is not correctly
answered, the connection is rejected. MS CHAP v2 was
originally designed by Microsoft as a PPP authentication
protocol to provide better protection for dial-up and
virtual private network (VPN) connections. With
Windows XP SP1, Windows XP SP2, Windows Server
2003, and Windows 2000 SP4, MS CHAP v2 is also an
EAP type.
Password Authentication Protocol (PAP) has two
variations: PAP and CHAP PAP. It verifies a user name
and password for PPP Internet connections, but it is not
as secure as CHAP, since it works only to establish the
initial link. PAP is also more vulnerable to attack because
it sends authentication packets throughout the network.
Nevertheless, PAP is more commonly used than CHAP
to log in to a remote host like an Internet service
provider.
X
EAP TLS is used during phase 2 of the authentication
process. This method uses a user certificate to
authenticate.
Wireless Configuration B - 13
User Certificate Selection
If you checked the User Certificate check box on the Tunneled Authentication dialog box or if TLS is the selected
authentication type, the Installed User Certificates dialog box displays. Select a certificate from the drop-down
list of currently installed certificates before proceeding. The selected certificate’s name appears in the
drop-down list. If the required certificate is not in the list, install it.
Figure B-9 Installed User Certificates Dialog Box
User Certificate Installation
There are two methods available to install a user certificate for authentication. The first is to obtain the user
certificate from the Certificate Authority (CA). This requires connectivity with that CA. The second method is to
install the user certificate from a file placed on the device.
To install a user certificate from the CA:
1.
Tap Install Certificate. The Import Certificate dialog box appears.
2.
Select Import User Cert from Server and tap OK. The Install from Server dialog box appears.
3.
Enter the User, Password, and Server information in their respective text boxes.
4.
Tap Retrieve. A Progress dialog indicates the status of the certificate retrieval or tap Exit to exit.
After the installation completes, the Installed User Certs dialog box displays and the certificate is available in the
drop-down for selection.
NOTE
To successfully install a user certificate, the mobile computer must already be connected to a network from
which the server is accessible.
To install a user certificate from a file:
1.
Tap Install Certificate. The Import Certificate dialog box appears.
2.
Choose Import from File and tap OK. The Open dialog box appears.
3.
In the Type drop-down list, select Personal Certs (*.pfx).
4.
Browse to the file and tap OK. The Personal Certificate dialog box appears.
5.
Enter the password and select OK. The certificate(s) are imported.
NOTE
To install a user certificate from a file, the file must be of type “*.pfx”. Also, this file type requires you to supply a
password in order to be read by Fusion.
B - 14 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Server Certificate Selection
If you select the Validate Server Certificate check box, a server certificate is required. Select a certificate on the
Installed Server Certificates dialog box. An hour glass may appear as the wizard populates the existing
certificate list. If the required certificate is not listed, install it:
1.
Tap the Install Certificate button.
Figure B-10 Installed Server Certificates Dialog Box
The Import Certificate dialog box appears. Choose Import from File (.cer, .pfx) and tap OK.
2.
A dialog box appears that lists the certificate files found with the default extension. Browse to the file and
tap OK.
3.
A confirmation dialog verifies the installation. If the information in this dialog is correct, tap the Yes button. If
the information in this dialog is not correct, tap the No button. The wizard returns to the Installed Server
Certs dialog box. Select the newly-installed certificate from the drop down list.
User Name
You can enter the user name and password when you create the profile, but is not required. If you do not enter
the username and password in the profile, then when attempting to connect, you are prompted to supply them.
The entered information (credentials) is saved (cached) for future reconnections.
Whether or not you enter the username and password into the profile affects how the profile is treated during a
Profile Roaming operation. Profiles are excluded from consideration if they require user entry of credential
information.
If the profile uses an authentication tunnel type of EAP-GTC and you selected Token (see Password), then you
can control certain behavior by whether you enter a value in the Enter User Name field. If you enter a value in
this field, when the Fusion software prompts you to enter credentials, the username field in the interactive
credential dialog is initialized with the value you entered when creating the profile. If you enter a different value
in the username field of the interactive credential dialog, it is cached and used to initialize the username field
the next time the interactive credential dialog is shown for that profile.
If you do not enter a value in the Enter User Name field when you create an EAP-GTC token profile, the
username field in the interactive credential dialog is initialized to blank. After you enter a username in the
interactive credential dialog, it is cached as usual, but it is not used to initialize the username field the next time
the interactive credential dialog is shown for that profile; the username field is still initialized to blank.
In summary, you can control whether the username field in the interactive credential dialog box is initialized,
either with the last interactively-entered username for that profile or with the username entered into the profile,
by whether any value is entered in the Enter User Name field during profile entry.
Wireless Configuration B - 15
Figure B-11 Username Dialog Box
Password
Use the Password dialog box to enter a password. If EAP/TLS is the selected authentication type, the
password dialog box does not appear. Note that if you entered a username but no password, Fusion assumes
that no password is a valid password.
Figure B-12 Password Dialog Box
1.
Enter a password in the Enter Password field. If using the authentication tunnel type EAP-GTC, a Password
dialog box appears, with two radio buttons to allow you to choose a token or static password.
• Choose the Token radio button when using the profile in conjunction with a token generator (hardware
or software). The system administrator supplies a token generator for use with EAP-GTC token
profiles. A token generator generates a numeric value to enter in the password field at connect time,
usually along with a PIN. Tokens usually expire within 60 seconds. The token generator is
time-synchronized with a token server. When authenticating, the RADIUS server asks the token
server to verify the token entered. The token server knows what value the token generator generates
given the time of day and the username. Since tokens expire, EAP-GTC token profiles are treated
differently. A prompt appears at the appropriate time to enter a token, even if you previously entered a
token. Tokens are never cached in the credential cache (though the username entered when the
token is entered is cached).
• If you choose the Static radio button, the Enter Password field is enabled and you can enter a
password if desired. A profile that uses an EAP-GTC tunnel type with a static password is handled in
the same manner as other profiles that have credentials that don't expire.
2.
Select the Advanced ID check box if advanced identification is desired.
3.
Tap Next. The Prompt for Login at dialog box displays. See Credential Cache Options.
B - 16 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Advanced Identity
Use the Advanced ID dialog box to enter the 802.1X identity to supply to the authenticator. This value can be 63
characters long and is case sensitive. In TTLS and PEAP, entering an anonymous identity (rather than a true
identity) plus any desired realm (e.g., anonymous@myrealm) is recommended. A user ID is required before
proceeding.
NOTE
When authenticating with a Microsoft IAS server, do not use advanced identity.
Figure B-13 Advanced Identity Dialog Box
Tap Next. The Encryption dialog box displays.
Credential Cache Options
If you selected any of the password-based authentication types, you can select different credential caching
options. These options specify when the network credential prompts appear: at connection, on each resume,
or at a specified time.
Entering the credentials directly into the profile permanently caches the credentials. In this case, the device
does not require user login. If a profile does not contain credentials entered through the Profile Editor Wizard,
you must enter credentials when prompted, either when connecting to the profile in the Manage Profiles
window, or when logging onto the profile using the Log On/Off command.
Credential caching options only apply to a profile when you enter credentials through the login dialog box. This
includes using the Log On/Off command to log on to a profile for which the credentials were directly entered
into the profile (the username / password fields left blank).
Figure B-14 Prompt for Login at Dialog Box
If the device does not have the credentials, you are prompted to enter a username and password. If the device
has the credentials (previous entered via a login dialog box), it uses these credentials unless the caching
options require the device to prompt for new credentials. If you entered the credentials via the profile, the
device does not prompt for new credentials (except for profiles where the credentials expire, such as
EAP-GTC token profiles). Table B-10 lists the caching options.
Wireless Configuration B - 17
Table B-10 Cache Options
Option
Description
At Connect
Select this option to prompt for credentials whenever the device tries to connect to a new
profile. Deselect this to use the cached credentials to authenticate. If the credentials are not
cached, you are prompted to enter credentials. This option only applies when logged in.
On Resume
Selecting this reauthenticates an authenticated user when a suspend/resume occurs. Once
reauthenticated, the user is prompted for credentials. If the user does not enter the same
credentials that were entered prior to the suspend/resume within three attempts, the user is
disconnected from the network. This option only applies when logged in.
At Time
Select this option to perform a local verification on an authenticated user at a specified time.
The time can be an absolute time or a relative time from the authentication, and should be
in at least 5 minute intervals. Once the time has passed, the user is prompted for
credentials. If the user does not enter the correct credentials within three attempts, the user
is disconnected from the network. This option only applies when logged in.
Entering credentials applies these credentials to a particular profile. Logging out clears all cached credentials.
Editing a profile clears all cached credentials for that profile. If you configure the APs to use the Fast Session
Resume capability available with some authentication types (e.g., PEAP), do not check At Connect or On
Resume if you want to avoid being prompted to re-enter credentials in circumstances in which Fast Session
Resume would allow them not to be.
The following authentication types have credential caching:
•
EAP-TLS
•
PEAP
•
LEAP
•
TTLS
•
EAP-FAST.
Some exceptions to the credential caching rules apply for profiles where the credentials expire, such as
EAP-GTC token profiles. Since the token expires after a short period, you are prompted for credentials even
when credentials were already entered and cached for that profile. The At Connect caching option has a
slightly different function. If do not check the At Connect box, the Fusion software tries to authenticate without
prompting for a new token. If Fast Session Reconnect is enabled on the RADIUS server and the device was
previously connected and authenticated using the same profile, the device may be able to reconnect without
the entire authentication process. In this case, new credentials are not required (even though the old ones
have expired) and the Fusion software does not prompt for new credentials. If Fast Session Reconnect is not
enabled on the RADIUS server or if you checked the At Connect checkbox, you are prompted to enter new
credentials. Note also that the On Resume caching option must always check for profiles where the credentials
expire, because the Fusion software does not support the use of Fast Session Reconnect across a
suspend/resume cycle, so new credentials are always needed.
B - 18 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Selecting the At Time check box displays the Time Cache Options dialog box.
Figure B-15 Time Cache Options Dialog Box
1.
Tap the Interval radio button to check credentials at a set time interval.
2.
Enter the value in minutes in the Min box.
3.
Tap the At (hh:mm) radio button to check credentials at a set time.
4.
Tap Next. The At Time dialog box appears.
Figure B-16 At Time Dialog Box
5.
Enter the time using the 24 hour clock format in the (hh:mm) box.
6.
Tap > to move the time to the right. Repeat for additional time periods.
7.
Tap Next. The Encryption dialog box displays.
Wireless Configuration B - 19
Encryption
NOTE
The only available encryption methods in Ad-hoc are Open, WEP40, and WEP104.
Use the Encryption dialog box to select an encryption method. This contains fields to configure the encryption
method and corresponding keys, if any. The drop-down list includes encryption methods available for the
selected security mode and authentication type.
Figure B-17 Encryption Dialog Box
Based on the encryption method and the authentication type, you may have to manually enter pre-shared
encryption keys (or a passkey phrase). When you select any authentication type other than None, 802.1x
authentication is used and the keys are automatically generated.
Table B-11 Encryption Options
Encryption
Description
Open
Select Open (the default) when no data packet encryption is needed over the network.
Selecting this option provides no security for data transmitting over the network.
WEP-40 (40/24)
Select WEP-40 (40/24) to use 64-bit key length WEP encryption (the other 24 bits are
generated automatically). Other controls appear that allow you to enter keys. If you select
the Use Passkey checkbox, you are asked to enter a passphrase between 4 and 32
characters long on the next page. Saving the profile converts the passphrase into a key
and the passphrase is lost. Also, if using a passkey, only one key can be set.
If you do not select the Use Passkey checkbox, you can enter up to four hexadecimal keys
on the next page. Select the key to enter in the Key Index drop-down menu. This also
selects the key used for encryption. Note that Fusion sets default values for these keys, so
while that entry is not required, the keys must match the AP.
B - 20 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Table B-11 Encryption Options (Continued)
Encryption
Description
WEP-104
(104/24)
Select WEP-104 (104/24) to use a 128-bit key length WEP encryption. Other controls
appear that allow you to enter keys. If you select the Use Passkey checkbox, you are
asked to enter a passphrase between 4 and 32 characters long on the next page. Saving
the profile converts the passphrase into a key and the passphrase is lost. Also, if using a
passkey, only one key can be set.
If you do not select the Use Passkey checkbox, you can enter up to four hexadecimal
keys on the next page. Select the key to enter in the Key Index drop-down menu. This
also selects the key used for encryption. Note that Fusion sets default values for these
keys, so while that entry is not required, the keys must match the AP.
TKIP
Select TKIP for the adapter to use the Temporal Key Integrity Protocol (TKIP) encryption
method. This encryption method is available when the Security Mode is not set to Legacy.
If the Security Mode is set to WPA personal, you are asked to enter a passphrase between
8 and 63 characters long on the next page.
AES
(Fusion 2.5 only)
Select this option for the adapter to use the Advanced Encryption Standard (AES) method.
This encryption method is available for many of the Security Modes. If the Security Mode
selected is “personal”, you are asked to enter a passphrase between 8 and 63 characters
long on the next page.
Table B-12 Encryption / Authentication Matrix
Encryption
Authentication
Legacy (Pre-WPA)
Open
None
Yes
WEP
WEP-40 or
WEP-104
WPA
Personal
WPA2
Personal
WPA
Enterprise
WPA2
Enterprise
TKIP
AES
TKIP
AES
Yes
Yes
EAP-TLS
WEP-104
Yes
Yes
EAP-FAST
WEP-104
Yes
Yes
PEAP
WEP-104
Yes
Yes
LEAP
WEP-104
Yes
Yes
TTLS
WEP-104
Yes
Yes
If you selected either WEP-40 (40/24) or WEP-104 (104/24), the wizard displays the Key Entry dialog box
unless you selected the Use Passkey check box in the Encryption dialog box (see Figure B-17 on page B-19).
The Key Entry dialog box appears only if the authentication is set to None.
Wireless Configuration B - 21
Key Entry Page - Hexidecimal Keys
To enter the hexidecimal key information select the Hexidecimal Keys radio button in the Encryption dialog box.
To enter a hexidecimal key with characters hidden:
1.
Select the For added security - Mask characters entered check box.
2.
Tap Next.
WEP-40 Keys Dialog Box
WEP-104 Keys Dialog Box
Figure B-18 WEP-40 and WEP-104 Keys Dialog Boxes
3.
For WEP only, in the Edit Key drop-down list, select the key to enter.
4.
In the Key field, enter the key.
a.
For WEP-40 enter 10 hexidecimal characters.
b.
For WEP-104 enter 26 hexidecimal characters.
c.
For TKIP enter 64 hexidecimal characters.
d.
For AES enter 64 hexidecimal characters.
5.
In the Confirm Key field, re-enter the key. When the keys match a message appears indicating this.
6.
Repeat for each WEP key.
7.
For WEP only, in the Transmit Key drop-down list, select the key to transmit.
8.
Tap Next. The IP Address Entry dialog box displays.
To enter a hexidecimal key without characters hidden:
1.
Tap Next.
2.
For WEP only, in each Key field, enter the key.
a.
For WEP-40 enter 10 hexidecimal characters.
b.
For WEP-104 enter 26 hexidecimal characters.
c.
For TKIP enter 64 hexidecimal characters.
d.
For AES enter 64 hexidecimal characters.
3.
For WEP only, in the Transmit Key drop-down list, select the key to transmit.
4.
Tap Next. The IP Address Entry dialog box displays.
B - 22 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Pass-phrase Dialog
When you select None as an authentication and WEP as an encryption, you can choose to enter a pass-phrase
by checking the Pass-phrase radio button. You are prompted to enter the pass-phrase. For WEP, the
Pass-phrase radio button is only available if the authentication is None.
When you select None as an authentication and TKIP as an encryption, you must enter a pass-phrase. You
cannot enter a pass-phrase if the encryption is TKIP and the authentication is anything other than None.
When you select None as an authentication and AES as an encryption, you must enter a pass-phrase. You
cannot enter a pass-phrase if the encryption is AES and the authentication is anything other than None.
To enter a pass-phrase with characters hidden:
1.
Select the For added security - Mask characters entered check box.
2.
Tap Next.
3.
In the Key field, enter the key.
a.
For WEP-40 enter between 4 and 32 characters.
b.
For WEP-104 enter between 4 and 32 characters.
c.
For TKIP enter between 8 and 63 characters.
d.
For AES enter between 8 and 63 characters.
4.
In the Confirm Key field, re-enter the key. When the keys match a message appears indicating this.
5.
Tap Next. The IP Address Entry dialog box displays.
To enter a pass-phrase key without characters hidden:
1.
Tap Next.
2.
In the Key field, enter the key.
3.
a.
For WEP-40 enter between 4 and 32 characters.
b.
For WEP-104 enter between 4 and 32 characters.
c.
For TKIP enter between 8 and 63 characters.
d.
For AES enter between 8 and 63 characters.
Tap Next. The IP Address Entry dialog box displays.
Wireless Configuration B - 23
IP Address Entry
Use the IP Address Entry dialog box to configure network address parameters: IP address, subnet mask,
gateway, DNS, and WINS.
Figure B-19 IP Address Entry Dialog Box
Table B-13 IP Address Entry
Encryption
Description
DHCP
Select Dynamic Host Configuration Protocol (DHCP) from the IP Address Entry
drop-down list to obtain a leased IP address and network configuration information from
a remote server. DHCP is the default setting for the device profile. Ad-hoc mode does
not support DHCP. Use only a Static IP address assignment.
Static
Select Static to manually assign the IP, subnet mask, default gateway, DNS, and WINS
addresses the device profile uses.
Select either DHCP or Static from the drop-down list and tap Next. Selecting Static IP displays the IP Address
Entry dialog box. Selecting DHCP displays the Transmit Power dialog box.
Use the IP Address Entry dialog box to enter the IP address and subnet information.
Figure B-20 Static IP Address Entry Dialog Box
B - 24 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Table B-14 Static IP Address Entry Fields
Field
Description
IP Address
The Internet is a collection of networks with users that communicate with each other.
Each communication carries the address of the source and destination networks and the
particular machine within the network associated with the user or host computer at each
end. This address is called the IP address (Internet Protocol address). Each node on the
IP network must be assigned a unique IP address that is made up of a network identifier
and a host identifier. Enter the IP address as a dotted-decimal notation with the decimal
value of each octet separated by a period, for example, 192.168.7.27.
Subnet Mask
Most TCP/IP networks use subnets to manage routed IP addresses. All IP addresses
have a network part and a host part. The network part specifies a physical network. The
host part specifies a host on that physical network. The subnet mask allows a network
administrator to use some of the bits that are normally used to specify the host to instead
specify physical sub-networks within an organization. This helps organize and simplify
routing between physical networks.
Select the Advanced check box, then tap NEXT to display the Advanced Address Entry dialog box. Enter the
Gateway, DNS, and WINS address. Tap NEXT without selecting the Advanced check box to display the
Transmit Power dialog box.
Figure B-21 Advanced Address Entry Dialog Box
The IP information entered in the profile is only used if you selected the Enable IP Mgmt check box in the
Options > System Options dialog box (System Options on page B-45). If you didn’t select this, the IP
information in the profile is ignored and the IP information entered in the Microsoft interface applies.
Table B-15 IP Config Advanced Address Entry Fields
Field
Description
G/W
The default gateway forwards IP packets to and from a remote destination.
DNS
The Domain Name System (DNS) is a distributed Internet directory service. DNS
translates domain names and IP addresses, and controls Internet email delivery. Most
Internet services require DNS to operate properly. If DNS is not configured, Web sites
cannot be located and/or email delivery fails.
WINS
WINS is a Microsoft® Net BIOS name server. WINS eliminates the broadcasts needed
to resolve computer names to IP addresses by providing a cache or database of
translations.
Tap Next. The Transmit Power dialog box displays.
Wireless Configuration B - 25
Transmit Power
The Transmit Power drop-down list contains different options for Ad-Hoc and Infrastructure mode. Automatic
(i.e., use the current AP settings) and Power Plus (use higher than the current AP settings) are available for
Infrastructure mode.
Adjusting the radio transmission power level enables you to expand or confine the transmission coverage area.
Reducing the radio transmission power level reduces potential interference to other wireless devices that might
be operating nearby. Increasing the radio transmission power level increases the range at which other wireless
devices can “hear” the radio's signal.
Figure B-22 Transmit Power Dialog Box (Infrastructure Mode)
Table B-16 Transmit Power Dialog Box (Infrastructure Mode)
Field
Description
Automatic
Select Automatic (the default) to use the AP power level.
Power Plus
Select Power Plus to set the device transmission power one level higher than the level
set for the AP. The power level is set to conform to regulatory requirements.
Figure B-23 Transmit Power Dialog Box (Ad-Hoc Mode)
B - 26 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Table B-17 Power Transmit Options (Ad-Hoc Mode)
Field
Description
Full
Select Full power for the highest transmission power level. Select Full power when
operating in highly reflective environments and areas where other devices could be
operating nearby, or when attempting to communicate with devices at the outer edge of a
coverage area.
30 mW
Select 30 mW to set the transmit power level to 30 mW. The radio transmits at the minimum
power required.
15 mW
Select 15 mW to set the transmit power level to 15 mW. The radio transmits at the minimum
power required.
5 mW
Select 5 mW to set the transmit power level to 5 mW. The radio transmits at the minimum
power required.
1 mW
Select 1 mW for the lowest transmission power level. Use this level when communicating
with other devices in very close proximity, or in instances where you expect little or no radio
interference from other devices.
Tap Next to display the Battery Usage dialog box.
Wireless Configuration B - 27
Battery Usage
Use the Battery Usage dialog box to select power consumption of the wireless LAN. There are three settings
available: CAM, Fast Power Save, and MAX Power Save. Battery usage cannot be configured in Ad-Hoc
profiles.
Figure B-24 Battery Usage Dialog Box
NOTE
Power consumption is also related to the transmit power settings.
Table B-18 Battery Usage Options
Field
Description
CAM
Continuous Aware Mode (CAM) provides the best network performance, but yields
the shortest battery life.
Fast Power Save
Fast Power Save (the default) performs in the middle of CAM and MAX Power Save
with respect to network performance and battery life.
MAX Power Save
Max Power Save yields the longest battery life while potentially reducing network
performance. In networks with minimal latency, Max Power Save performs as well
as Fast Power Save, but with increased battery conservation.
B - 28 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Manage Profiles Application
The Manage Profiles window provides a list of user-configured wireless profiles. Define up to 32 profiles at any
one time. To open the Manage Profiles window, tap the Signal Strength icon > Manage Profiles.
Figure B-25 Manage Profiles Window
Icons next to each profile identify the profile’s current state.
Table B-19 Profile Icons
Icon
No Icon
Description
Profile is not selected, but enabled.
Profile is disabled.
Profile is cancelled. A cancelled profile is disabled until a connect or login function is performed
through the configuration editor.
Profile is in use and describes an infrastructure profile not using encryption.
Profile is in use and describes an infrastructure profile using encryption.
Profile is in use and describes an ad-hoc profile not using encryption.
Profile is in use and describes an ad-hoc profile using encryption.
Profile is not valid in the device current operating regulatory domain.
The profiles are listed in priority order for use by the automatic roaming feature. Change the order by moving
profiles up or down. To edit existing profiles, tap and hold one in the list and select an option from the menu to
connect, edit, disable (enable), or delete the profile. Note that the Disable menu item changes to Enable if the
profile is already disabled.
Wireless Configuration B - 29
Figure B-26 Manage Profiles Context Menu
Changing Profiles
A completed profile is a set of configuration settings that you can use in different locations to connect to a
wireless network. Create different profiles to have pre-defined operating parameters available for use in
various network environments. When the WLAN Profiles window displays, existing profiles appear in the list.
Figure B-27 Manage Profiles
Tap and hold a profile and select Connect from the pop-up menu to set this as the active profile. Once selected,
the device uses the authentication, encryption, ESSID, IP Config, and power consumption settings configured
for that profile.
Editing a Profile
Tap and hold a profile and select Edit from the pop-up menu to display the Profile Wizard where you can
configure the profile settings. See Profile Editor Wizard on page B-5 for instructions on editing a profile.
B - 30 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Creating a New Profile
To create new profiles from the Manage Profiles window, tap-and-hold anywhere in this window.
Figure B-28 Manage Profiles - Add
Select Add to display the Profile Wizard wherein you can configure the profile settings, such as profile name,
ESSID, security, network address information, and the power consumption level. See Profile Editor Wizard on
page B-5 for instructions on creating a profile.
Deleting a Profile
To delete a profile from the list, tap and hold and select Delete from the pop-up menu. A confirmation dialog box
appears.
Ordering Profiles
Tap and hold a profile from the list and select Move Up or Move Down to order the profile. If the current profile
association is lost, the device attempts to associate with the first profile in the list, then the next, until it
achieves a new association.
NOTE
Profile Roaming must be enabled in the Options application. See System Options on page B-45.
Wireless Configuration B - 31
Export a Profile
To export a profile to a registry file, tap and hold a profile from the list and select Export from the pop-up menu.
The Save As dialog box displays with the Application folder and a default name of WCS_PROFILE{profile
GUID}.reg (Globally Unique Identifier).
Figure B-29 Save As Dialog Box
If required, change the name in the Name field and tap Save. A confirmation dialog box appears after the export
completes.
Manage Certificates
You can view and manage security certificates in the various certificate stores. Tap the Signal Strength icon >
Manage Certs. The Certificate Manager window displays.
Various certificate types display. Select the Certificate Type drop-down box to filter the certificate list to display
All, only Root/Server, or only User/Client certificates.
The Certificate Manager window contains command buttons at the bottom of the window. A button might be
disabled (gray) if the operation cannot be performed based on any selected object.
To hide the command buttons to allow more space for displaying certificates, tap-and-hold and/or double-tap in
the list area. In the pop-up menu, select Hide Buttons. To display the buttons, select View Buttons.
You can also use the pop-up menu to select the Properties, Import, and Delete commands.
Certificate Properties
To display the properties of a certificate, select a certificate in the list and tap the Properties button. Select a
property in the upper list to display the detailed information in the Expanded Value section.
Tap ok, Escape, or X to exit (depending on the device).
B - 32 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Import a Certificate
Import a certificate from a file or from a server:
•
.CER file - DER encrypted Root/Server certificates.
•
.PFX file - Personal inFormation eXchange formatted file containing one or more Root/Server and/or
User/Client Certificates. These files are usually protected by a password you must enter. If there is no
password, enter nothing and select the OK button.
•
Server - You can request User/Client certificates directly from a Certificate Authority (CA) on the network.
You must provide a User name, Password (optional), and the Server (an IP address) to obtain a
certificate for the User from the CA.
To import from a file:
1.
Tap the Import button or select from the context menu. The Import Certificate dialog box displays.
2.
Select the Import from File (.cer, .pfx) radio button to import a certificate file.
3.
Select the file to import from the Open window.
To import from a server:
1.
Tap the Import button or select from the context menu. The Import Certificate dialog box displays.
2.
Select the Import User Cert from Server radio button to import a certificate from a server. The Install From
Server window displays.
3.
Enter the user, password, and server information in the respective text boxes.
4.
Tap the Retrieve button to import the certificate.
Delete a Certificate
To delete a certificates:
1.
Select the certificate to delete.
2.
Tap the Delete button or select Delete from the pop-up menu.
Wireless Configuration B - 33
Manage PACs
You can view and manage Protected Access Credentials (PACs) used by Cisco's EAP-FAST authentication
protocol. PACs are uniquely identified by referencing a PAC Authority Identifier (A-ID) (the server that issued
the PAC) and by the individual user identifier (I-ID). The PACs display sorted by A-ID (default) or by I-ID in a
tree display.
Tap the Signal Strength icon > Manage PACs. The PAC Manager window displays.
To hide the buttons on the PAC Manager window to allow more space for displaying certificates, tap-and-hold or
double-tap in the list area and select Hide Buttons. A button is disabled (gray) if the operation cannot be
performed based on any selected object.
To display the buttons, select View Buttons from the pop-up menu.
You can also use the pop-up menu to select the Properties and Delete commands, or to sort by A-ID or I-ID.
PAC Properties
To display the properties of a PAC, select an item in a sub-tree, and select the Properties button or pop-up
menu. Select an entry in the upper list of the window to display the details of that property in the lower list.
To return to the main page, tap Ok, Escape, or X.
Delete PAC
To delete a single PAC, tap a leaf item (right-most tree item) to select the PAC, then select the Delete button or
Delete on the pop-up menu. A confirmation dialog box appears.
To delete a group of PACs with the same A-ID or I-ID, sort the PACs by ID type, then tap on the parent item
(left-most tree item) to select the group. Select the Delete button or Delete on the pop-up menu. A confirmation
dialog box appears.
B - 34 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Wireless Status Application
To open the Wireless Status window, tap the Signal Strength icon > Wireless Status. The Wireless Status window
displays information about the wireless connection.
Figure B-30 Wireless Status Window
The Wireless Status window contains the following options. Tap the option to display the option window.
•
Signal Strength - provides information about the connection status of the current wireless profile.
•
Current Profile - displays basic information about the current profile and connection settings.
•
IPv4 Status - displays the current IP address, subnet, and other IP related information assigned to the
device.
•
Wireless Log - displays a log of important recent activity, such as authentication, association, and DHCP
renewal completion, in time order.
•
Versions - displays software, firmware, and hardware version numbers.
•
Quit - exits the Wireless Status window.
Option windows contain a back button
to return to the main Wireless Status window.
Wireless Configuration B - 35
Signal Strength Window
The Signal Strength window provides information about the connection status of the current wireless profile
including signal quality, missed beacons, and transmit retry statistics. The BSSID address (shown as AP MAC
Address) displays the AP currently associated with the connection. In Ad-Hoc mode, the AP MAC Address
shows the BSSID of the Ad-Hoc network. Information in this window updates every 2 seconds.
To open the Signal Status window, tap Signal Strength in the Wireless Status window.
Figure B-31 Signal Strength Window
After viewing the Signal Strength window, tap the back button to return to the Wireless Status window.
Table B-20 Signal Strength Status
Field
Signal
Description
Displays the Relative Signal Strength Indicator (RSSI) of the signal transmitted
between the AP and device. As long as the Signal Quality icon is green the AP
association is not jeopardized. If the icon is red (poor signal), an association with a
different AP could be warranted to improve the signal. The signal strength icon
changes depending on the signal strength.
Excellent Signal
Very Good Signal
Good Signal
Fair Signal
Poor Signal
Out of Range (no signal)
The radio card is off or there is a problem communicating with the radio
card.
Status
Indicates if the device is associated with the AP.
Signal Quality
Displays a text format of the Signal icon.
Tx Retries
Displays a percentage of the number of data packets the device retransmits. The
fewer transmit retries, the more efficient the wireless network is.
Missed Beacons
Displays a percentage of the amount of beacons the device missed. The fewer
missed beacons, the more efficient the wireless network is. Beacons are uniform
system packets broadcast by the AP to keep the network synchronized.
Signal Level
The AP signal level in decibels per milliwatt (dBm).
Noise Level
The background interference (noise) level in decibels per milliwatt (dBm).
B - 36 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Table B-20 Signal Strength Status (Continued)
Field
Description
SNR
The access point/device Signal to Noise Ratio (SNR) of signal strength to noise
(interference) in decibels per milliwatt (dBm).
Association Count
Displays the number of times the device has roamed from one AP to another.
AP MAC Address
Displays the MAC address of the AP to which the device is connected.
Transmit Rate
Displays the current rate of the data transmission.
Current Profile Window
The Current Profile window displays basic information about the current profile and connection settings. This
window updates every two seconds.
To open the Current Profile window, tap Current Profile in the Wireless Status window.
Figure B-32 Current Profile Window
Table B-21 Current Profile Window
Field
Description
Profile Name
Displays the current profile name the device uses to communicate with the AP.
ESSID
Displays the current profile’s ESSID name.
Mode
Displays the current profile’s mode, either Infrastructure or Ad-Hoc.
Authentication
Displays the current profile’s authentication type.
Encryption
Displays the current profile’s encryption type.
Channel
Displays the current profile’s channel setting.
Country
Displays the current profile’s country setting.
Transmit Power
Displays the radio transmission power level.
Wireless Configuration B - 37
IPv4 Status Window
The IPv4 Status window displays the current IP address, subnet, and other IP related information assigned to
the device. It also allows renewing the address if the profile is using DHCP to obtain the IP information. Tap
Renew to initiate the IP address renewal process. The IPv4 Status window updates automatically when the IP
address changes.
To open the IPv4 Status window, tap IPv4 Status in the Wireless Status window.
Figure B-33 IPv4 Status Window
Table B-22 IPv4 Status Fields
Field
Description
IP Type
Displays the IP address assignment method used for the current profile: DHCP or Static. If
the IP Type is DHCP, the IP address and other information shown is obtained from the DHCP
server. The DHCP server address and the lease information also appears.
If the IP Type is Static, the window displays the IP address and other information entered in
the profile.
IP Address
Displays the device’s IP address. The Internet is a collection of networks with users that
communicate with each other. Each communication carries the address of the source and
destination networks and the particular machine within the network associated with the user
or host computer at each end. This address is called the IP address. Each node on the IP
network must be assigned a unique IP address that is made up of a network identifier and
a host identifier. The IP address as a dotted-decimal notation with the decimal value of each
octet separated by a period, for example, 192.168.7.27.
Subnet
Displays the device’s subnet address. Most TCP/IP networks use subnets to manage
routed IP addresses. All IP addresses have a network part that specifies a physical
network, and a host part that specifies a host on that physical network. The subnet mask
allows a network administrator to use some of the bits typically used to specify the host, to
instead specify physical sub-networks within an organization. This helps organize and
simplify routing between physical networks.
Gateway
Displays the gateway address. A gateway forwards IP packets to and from a remote
destination.
DCHP Server
Displays the IP addresses of the DHCP server.
Lease
Obtained
Displays the date and time that the IP address was obtained.
Lease Expires
Displays the date and time that the IP address expires.
B - 38 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Table B-22 IPv4 Status Fields (Continued)
Field
Description
DNS
Displays the IP address of the DNS server.
WINS
WINS is a Microsoft Net BIOS name server. WINS eliminates the broadcasts needed to
resolve computer names to IP addresses by providing a cache or database of translations.
MAC
An IEEE 48-bit address is assigned to the device at the factory to uniquely identify the
adapter at the physical layer.
Host Name
Displays the name of the device.
Wireless Log Window
The Wireless Log window displays a log of recent activity, such as authentication, association, and DHCP
renewal completion, in time order. Save the log to a file or clear the log (within this instance of the application
only). The auto-scroll feature automatically scrolls down when new items are added to the log.
To open the Wireless Log window, tap Wireless Log in the Wireless Status window. The Wireless Log window
displays.
Figure B-34 Wireless Log Window
Saving a Log
To save a Wireless Log:
1.
Tap the Save button. The Save As dialog box displays.
2.
Navigate to the desired folder.
3.
In the Name filed, enter a file name and then tap OK. The Wireless Log is saved as a text file in the selected
folder.
Clearing the Log
To clear the log, tap Clear.
Wireless Configuration B - 39
Versions Window
The Versions window displays software, firmware, and hardware version numbers.
To open the Versions window, tap Versions in the Wireless Status window.
Figure B-35 Versions Window
The window displays software version numbers as well as application and middleware version information.
Wireless Diagnostics Application
The Wireless Diagnostics application window provides links to perform ICMP Ping, Trace Routing, and Known
APs. To open the Wireless Diagnostics window, tap the Signal Strength icon > Wireless Diagnostics.
Figure B-36 Wireless Diagnostics Window
The Wireless Diagnostics window contains the following options. Tap the option to display the option window.
•
ICMP Ping - tests the wireless network connection.
•
Trace Route - tests a connection at the network layer between the device and any place on the network.
•
Known APs - displays the APs in range using the same ESSID as the device.
•
Quit - Exits the Wireless Diagnostics window.
Option windows contain a back button
to return to the Wireless Diagnostics window.
B - 40 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
ICMP Ping Window
The ICMP Ping window allows testing a connection at the network layer (part of the IP protocol) between the
device and any other device on the network. Ping tests only stop when you tap the Stop Test button, close the
Wireless Diagnostics application, or if the device switches between infrastructure and ad-hoc modes.
To open the ICMP Ping window, tap the ICMP Ping in the Wireless Diagnostics window.
Figure B-37 ICMP Ping Window
To perform an ICMP ping:
1.
In the IP field, enter an IP address or select an IP address from the drop-down list.
2.
From the Size drop-down list, select a size value.
3.
Tap Start Test. The ICMP Ping test starts. Information of the ping test displays in the appropriate fields.
The following statistics appear on the page:
•
Signal - The current signal strength, measured in dBm, appears as both a numeric value and as a
histogram.
•
Noise - The current noise level, measured in dBm, appears as both a numeric value and as a histogram.
•
SNR - The current signal to noise ratio, measured in dBm, appears as both a numeric value and as a
histogram.
•
Total Tx - The total number of pings sent appears numerically.
•
Total Rx - The total number of valid ping responses received appears numerically.
•
Lost - The total number of pings lost appears numerically.
•
RT Times - Four round trip times: Last, Average, Minimum, and Maximum appear in milliseconds.
•
% Rates - For each of the 12 data rates, the number of times that rate was used to transmit the ping
appears as a percentage.
Graphs
Double-tap a statistic listed above to display a real time graph of that statistic.
Wireless Configuration B - 41
Trace Route Window
Trace Route traces a packet from a computer to a host, showing how many hops the packet requires to reach
the host and how long each hop takes. The Trace Route utility identifies where the longest delays occur.
The Trace Route window allows testing a connection at the network layer (part of the IP protocol) between the
device and any other device on the network.
To open the Trace Route window, tap Trace Route in the Wireless Diagnostics window.
Figure B-38 Trace Route Window
In the IP combo box, enter an IP address or choose one from the drop-down list, or enter a DNS Name, and
tap Start Test. When starting a test, the trace route attempts to find all routers between the device and the
destination. The Round Trip Time (RTT) between the device and each router appears, along with the total test
time. The total test time may be longer than all RTTs added together because it does not only include time on
the network.
B - 42 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Known APs Window
The Known APs window displays the APs in range using the same ESSID as the device. This window is only
available in Infrastructure mode. To open the Known APs window, tap Known APs in the Wireless Diagnostics
window.
Figure B-39 Known APs Window
See Table B-23 for the definitions of the icons next to the AP.
Table B-23 Current Profile Window
Icon
Description
The AP is the associated access point, and is set to mandatory.
The AP is the associated access point, but is not set to mandatory.
The device is not associated to this AP, but the AP is set as mandatory.
The device is not associated to this AP, and AP is not set as mandatory.
Tap and hold on an AP to display a pop-up menu with the following options: Set Mandatory and Set Roaming.
Select Set Mandatory to prohibit the device from associating with a different AP. The letter M displays on top of
the icon. The device connects to the selected AP and never roams until:
•
You select Set Roaming.
•
You select Set Mandatory on a different AP.
•
You manually connect to a profile from the Manage Profiles page.
•
The device roams to a new profile.
•
The device resumes after being suspended.
•
The device resets (warm or cold).
Select Set Roaming to allow the device to roam to any AP with a better signal. These settings are temporary
and never saved to the registry.
Tap Refresh to update the list of the APs with the same ESSID.
Wireless Configuration B - 43
Options
Use the wireless Option dialog box to select one of the following operation options from the drop-down list:
•
Operating Mode (Op Mode) Filtering
•
Regulatory
•
Band Selection
•
System Options
•
Auto PAC Settings
•
Change Password
•
Export.
Operating Mode Filtering
The Operating Mode Filtering options cause the Find WLANs application to filter the available networks found.
Figure B-40 OP Mode Filtering Dialog Box
The AP Networks and Ad-Hoc Networks check boxes are selected by default.
Table B-24 OP Mode Filtering Options
Field
Description
AP Networks
Select the AP Networks check box to display available AP networks and their signal
strength within the Available WLAN Networks (see Find WLANs Application on page
B-4). These are the APs available to the device for association. If this option was
previously disabled, refresh the Available WLAN Networks window to display the AP
networks available to the device.
AD-Hoc Networks
Select the Ad-Hoc Networks check box to display available peer (adapter) networks
and their signal strength within the Available WLAN Networks. These are peer
networks available to the device for association. If this option was previously
disabled, refresh the Available WLAN Networks window to display the Ad Hoc
networks available to the device.
Tap Save to save the settings or tap X to discard any changes.
B - 44 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Regulatory Options
Use the Regulatory settings to configure the country the device is in. Due to regulatory requirements (within a
country) a device is only allowed to use certain channels.
Figure B-41 Regulatory Options Dialog Box
Table B-25 Regulatory Options
Field
Description
Settings
Select the country from the drop-down list. If you did not select the Enable 802.11d
check box, the profile country must match this setting to connect to that profile.
Enable 802.11d
If you select the Enable 802.11d check box, the WLAN adapter follows the 802.11d
standard. It passively scans until it receives valid country information from an AP. It
limits transmit power settings based on maximums received from the AP.
Profiles using Infrastructure mode can only connect if the country selected in the
profile matches the AP country setting, or if the profile country setting is Allow Any
Country.
Profiles which use Ad-hoc mode are not 802.11d compliant.
Band Selection
The Band Selection settings identify the frequency bands to scan when finding WLANs. These values refer to
the 802.11 standard networks.
NOTE
Select one band for faster access when scanning for WLANs.
Not all mobile devices support both 2.4 GHz and 5 GHz bands.
Figure B-42 Band Selection Dialog Box
Table B-26 Band Selection Options
Field
Description
2.4GHz Band
The Find WLANs application list includes all networks found in the 2.4 GHz band
(802.11b and 802.11g).
5GHz Band
The Find WLANs application list includes all networks found in the 5 GHz band (802.11a).
Tap Save to save the settings or tap X to discard any changes.
Wireless Configuration B - 45
System Options
Use System Options to set miscellaneous system setting.
Figure B-43 System Options Dialog Box
Table B-27 System Options
Field
Description
Profile Roaming
Configures the device to roam to the next available WLAN profile when it moves out of
range of the current WLAN profile.
Enable IP Mgmt
Enables the Wireless Companion Services to handle IP address management. The
Wireless Companion Service configures the IP based on what is configured in the
network profile. Deselect this to manually configure the IP in the standard Windows IP
window. Enabled by default.
Auto Time Config
Enables automatic update of the system time. Network association updates the device
time based on the time set in the AP. This proprietary feature is only supported with
infrastructure. Enabled by default.
Auto PAC Settings
Use the Auto PAC Settings to configure whether to allow automatic PAC provisioning and automatic PAC
refreshing when using the EAP-FAST authentication protocol.
Figure B-44 Auto PAC Settings Dialog Box
Table B-28 Auto PAC Settings
Field
Description
Allow Provisioning
Select Yes from the drop-down list to allow automatically provisioning the device with
a PAC when using the EAP-FAST authentication protocol. Select No to disallow
automatic PAC provisioning.
Allow Refreshing
Select Yes from the drop-down list to allow automatically refreshing an existing PAC
on the device when using the EAP-FAST authentication protocol. Select No to
disallow automatic PAC refreshing.
If the master key expires, you must manually delete the PAC on the device generated with this expired key and
provision a new PA, even if Allow Refreshing is enabled.
B - 46 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Change Password
Use Change Password to require a password before creating or editing a profile or changing the Options. This
allows pre-configuring profiles and prevents users from changing the network settings. The user can use this
feature to protect settings from a guest user. By default, the password is not set.
Figure B-45 Change Password Window
Enter the current password in the Current text box. If there is no current password, the Current text box does
not appear. Enter the new password in the New and Confirm text boxes. Tap Save.
To change an existing password, enter the current password in the Current: text box and enter the new
password in the New: and Confirm: text boxes. Tap Save.
To delete the password, enter the current password in the Current: text box and leave the New: and Confirm:
text boxes empty. Tap Save.
NOTE
Passwords are case sensitive and can not exceed 63 characters.
Wireless Configuration B - 47
Export
Use Export to export all profiles to a registry file, and to export the options to a registry file.
NOTE
For Windows CE 5.0 devices, exporting options enables settings to persists after cold boot. See Cold Boot
Persistence on page B-48 for more information.
Figure B-46 Options - Export Dialog Box
To export options:
1.
Tap Export Options. The Save As dialog box displays.
Figure B-47 Export Options Save As Dialog Box
2.
Enter a filename in the Name: field. The default filename is WCS_OPTIONS.REG.
3.
Select the desired folder.
4.
Tap Save.
To export all profiles:
1.
Tap Export All Profiles. The Save As dialog box displays.
Figure B-48 Export All Profiles Save As Dialog Box
B - 48 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
2.
Enter a filename in the Name: field. The default filename is WCS_PROFILES.REG.
3.
In the Folder: drop-down list, select the desired folder.
4.
Tap Save.
Selecting Export All Profiles saves the current profile. This information is used to determine which profile to
connect with after a warm boot or cold boot.
Cold Boot Persistence
Export options and profiles to provide cold boot persistence. Save the exported registry files in the Application
folder to use them on a cold boot and restore previous profile and option settings.
To save server certificates for persistence, save the certificate files in the folder Application\RootCerts to install
the certificates automatically on a cold boot.
User certificates that you install into the Microsoft Certificate Store, either through the Profile Editor Wizard or
through the Fusion Certificate Manager application, are automatically saved in a special format to files in the
Application\UserCerts folder. On a cold boot, the user certificates are automatically restored.
Registry Settings
Use a registry key to modify some of the parameters. The registry path is:
HKLM\SOFTWARE\Symbol Technologies, Inc.\Configuration Editor
Table B-29 Registry Parameter Settings
Key
Type
Default
Description
CertificateDirectory
REG_SZ
\\Application
The default directory to find certificates.
EncryptionMask
REG_DWORD
0x0000001F
Defines the supported encryption types. This is a
bitwise mask with each bit corresponding to an
encryption type.
1 = Type is supported
0 = Type is not supported
Bit Number
0
1
2
3
4
Encryption Type
None
40-Bit WEP
128-Bit WEP
TKIP
AES (Fusion 2.5 and above only)
Wireless Configuration B - 49
Log On/Off Application
When you launch the Log On/Off application, the device may be in one of two states: either you are logged onto
the device by already entering credentials through the login box, or you are not logged on. Each state has a
separate set of use cases and a different look to the dialog box.
User Already Logged In
If already logged into the device, you can launch the login dialog box for the following reasons:
•
Connect to a different profile.
•
Connect to and re-enable a cancelled profile. To do this:
• Launch the Log On/Off dialog.
• Select the cancelled profile from the profile drop-down list.
• Login to the profile.
NOTE
Re-enable cancelled profiles using the Manage Profiles window to connect to the cancelled profile.
•
Log off the device to prevent another user from accessing the current user’s network privileges.
•
Switch device users to quickly log off the device and allow another user to log into the device.
B - 50 MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
No User Logged In
If no user is logged into the device, launch the login dialog box and log in to access user profiles. The Login
dialog box varies if it is:
•
Launched by the wireless application, because the service is connecting to a new profile that needs
credentials.
•
Launched by the wireless application, because the service is trying to verify the credentials due to
credential caching rules.
•
Launched by a user, when a user is logged in.
•
Launched by a user, when no user is logged in.
Table B-30 Log On/Off Options
Field
Description
Wireless Profile
When launching the login application, this field has available all the wireless
profiles that require credentials. This includes profiles that use EAP-TLS,
PEAP, LEAP, EAP-TTLS, or EAP-FAST.
Profile Status Icon
This icon (next to the profile name) indicates one of the following states:
The selected profile is cancelled.
The selected profile is enabled but is not the current profile.
The profile is the current profile (always the case when the Wireless Application
is launched).
Username, Password, and
Domain Name
These fields are used as credentials for the profile selected in the Wireless
Profile field. The Password fields is limited to 63 characters. The Username and
Domain Name fields combined are limited to 63 characters. Note if any of the
above field labels are red, the entry is mandatory; if the field labels are black,
the entry is optional.
Mask Password Checkbox
Select this checkbox to mask the password field (so it displays only the '*'
character). This is the default.
Uncheck this to unmask the field (so it displays the entered text).
Status
This field indicates the reason the dialog is open.
Tapping OK sends the credentials though the Wireless Application API. If you did not enter credentials, a dialog
box prompts you to fill in all required fields.
The Log Off button only displays when you are already logged on. When you tap the Log Off button, you are
prompted with three options: Log Off, Switch Users, and Cancel. Switching users logs you off and re-initializes
the login dialog box when there is no user logged on. Logging off closes the login dialog box. Tapping Cancel
closes the Log Off dialog box and displays the Login dialog box.
When logged off, the device only roams to profiles that do not require credentials or to profiles that were
created with the credentials entered into the profile.
The Cancel button closes the dialog without logging into the network. If the login dialog was launched by the
Wireless Application and not by the user, tapping Cancel first causes a message box to display a warning that
the cancel disables the current profile. If you still choose to cancel the login, the profile is cancelled.
Once you cancel a profile, the profile is suppressed until you actively re-enable it or a new user logs onto the
device.
APPENDIX C TROUBLESHOOTING
Overview
The MK4000 troubleshooting is provided in three sections:
•
Troubleshooting on page C-2 offers troubleshooting scenarios for the MK4000.
•
MK4000 Version Information on page C-4 describes how to identify the MK4000 version.
Troubleshooting Notes
When configuring the MK4000, save and reboot the MK4000 to apply the changes.
Troubleshooting
•
MK4000 does not turn on on page C-2
•
MK4000 appears to lock up upon bootup on page C-2
•
MK4000 does not respond to polls from the host computer on page C-2
•
MK4000 does not send data to host computer on page C-2
•
Scanner does not recognize configuration bar codes on page C-2
•
Reg file values are not copied into the Registry at boot time on page C-2
•
The screen does not respond to pen input on page C-2
•
Need to determine a device MAC address on page C-2
•
The wireless MK4000 does not retain its WEP Key encryption after a reboot on page C-3
•
The Mobile Companion icon does not appear in the task tray on page C-3
•
When downloading files to the MK4000 from a .zip file using ActiveSync, a message displays indicating
there is not enough free disk space to copy the application on page C-3
•
When downloading a large file over Ethernet, IE issues an insufficient memory message on page C-3
•
When upgrading using an SD card, the MK4000 cannot find files on the card on page C-3
•
Flash file system is corrupt on page C-3
C-2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
•
Copying large amount of files from PC card to the application folder fails with error "Access is denied" on
page C-3
Table C-1 Troubleshooting
Problem
Possible Causes
Possible Solutions
MK4000 does not turn on
No power to the
MK4000.
Connect the approved power supply to an
AC power source and to the MK4000 power
connector. See Figure 1-2 on page 1-3.
MK4000 appears to lock up upon
bootup
A utility with no user
interface was specified
as the first user
application, or user
application failed to run.
Either specify no user application, or a
UI-based application as the first user
application. If no user application is
specified, Explorer.exe is used.
Note: this is a substitution of Explorer.exe as
the user application, not protected mode.
MK4000 does not respond to polls
from the host computer
No communication
between the host and
MK4000.
Check cables to the MK4000. Ensure the
MK4000 address is the address the host is
polling.
Check communication parameters.
Open a command window using
Start > Programs > Command and type
ipconfig to list the status of all radio and
Ethernet interfaces.
MK4000 does not send data to host
computer
MK4000 is not
programmed to work
with the host.
Check setup communication parameters.
MK4000 is not
connected to the host.
Check cables to host computer.
Scanner does not recognize
configuration bar codes
The scan driver does not
support parameter bar
code scanning.
Configure the scanner using scanning
C API scanner object.
Reg file values are not copied into
the Registry at boot time
More than one .reg file
and duplicate registry
entries are present.
Review all .reg files in /Application and
/Platform and ensure they have no conflicts.
The screen does not respond to pen
input
The screen is not
properly calibrated, or is
off center.
Re-calibrate the screen.
Need to determine a device MAC
address
N/A
Open Start > Programs > CommandPrompt.
Type ipconfig /all
to display the MAC address next to
‘address’.
Troubleshooting
C-3
Table C-1 Troubleshooting (Continued)
Problem
Possible Causes
Possible Solutions
The wireless MK4000 does not
retain its WEP Key encryption after
a reboot
Encryption keys not
saved in
Spectrum24.reg.
Set encryption keys using Mobile
Companion, then select Start > Tools > Save
Spectrum24 to save them to
Spectrum24.reg.
Check communication parameter settings.
Open a command window using Start >
Programs > Command and type ipconfig to
list the status of all radio and Ethernet
interfaces.
The Mobile Companion icon does
not appear in the task tray
The radio software is not
present in the \platform
folder.
Verify presence of radio software or re-install
\Platform partition software.
When downloading files to the
MK4000 from a .zip file using
ActiveSync, a message displays
indicating there is not enough free
disk space to copy the application
Files cannot download
directly from a .zip file.
Extract/unzip the files to the host computer,
then transfer the unzipped files to the
MK4000 using ActiveSync.
When downloading a large file over
Ethernet, IE issues an insufficient
memory message
For some file types, IE
requires free RAM
equivalent to twice the
file's size.
This is an IE limitation.
When upgrading using an SD card,
the MK4000 cannot find files on the
card
The SD card is not
supported.
The MK4000 supports up to an 8 GB SD
card.
Flash file system is corrupt
Reset or power loss
during write to file
system.
Format file system partition using Start >
Settings > Control Panel > Storage Manager,
and re-install partition data.
Copying large amount of files from
PC card to the application folder
fails with error "Access is denied"
Archive bit of the folder
properties set.
Clear the archive bit of folder properties.
When using SaveConfig to save
settings and cycling power before
the Save Complete message
appears, the device does not boot
properly.
Similarly, when using C API to save
configurations, the device does not
boot properly.
Corrupt mkconfig.reg file.
Use ActiveSync to delete the existing
mkconfig.reg file or use Monitor to repartition
the Application partition.
If problems still occur, see MK4000 Version Information on page C-4 for system information before calling for
service help.
C-4
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
MK4000 Version Information
If an MK4000 is configured to launch an application on power-up, bypass this upon booting to access the
Windows® CE Desktop. See Accessing the Windows® CE Desktop on page 4-2.
1.
From the Windows® task bar, select Start > Settings > Control Panel.
2.
Select MK4000 identification from the Control Panel window to view the following information:
• Device name
• Description
• OS version
• Monitor version
• Display type
• Memory sizes.
APPENDIX D MK4000 DEMO
Overview
This appendix provides information on the MK4000 demo which illustrates device functions. For demo
material, including the cell phone coupon bar code, visit
https://devcentral.symbol.com/shwmessage.aspx?ForumID=256&MessageID=15967
Price Check #1
The Price Check #1 demo opening screen shows the price in large text with a small text description. From the
main screen, this demo has a button to show a non-functioning paging feature (it plays sound), a
non-functioning printing screen, and another button to check inventory. The inventory screen shows the
location of items in stock and can show inventory at other store locations. The final inventory screen allows
reserving merchandise by scanning a loyalty card.
Price Check #1 (Large text)
Figure D-1 Price Check #1 (Large text)
D-2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Price Check #2
The Price Check #2 demo opening screen shows smaller text than Price Check #1 but includes regular price,
sale price, and "you save" information. From the main screen, this demo has a button to show a
non-functioning paging feature (it plays sound), a non-functioning printing screen, and another button to check
inventory. The inventory screen shows the location of items in stock and can show inventory at other store
locations. The final inventory screen allows reserving merchandise by scanning the Loyal Coupon Printing
Data Matrix bar code (loyalty card).
Price Check #2 (Small text)
Figure D-2 Price Check #2 (Small text)
Special Order Pick Up
Special Order Pick Up indicates where a customer can pick up an ordered item. After scanning a bar code
(loyalty card), the kiosk tells the customer where to pick up an item, and offers an option to have an associate
deliver the item. If the customer selects Yes for the latter, the kiosk displays a message that an associate was
paged and the speaker plays the voice message "associate has been paged."
Special Order Pick Up
Figure D-3 Special Order Pick Up
MK4000 Demo
D-3
Loyalty Coupon Printing
Loyalty Coupon Printing allows a customer to scan a loyalty card to print out coupons at the kiosk.
Loyalty Coupon Printing
Figure D-4 Loyalty Coupon Printing
Loyalty Coupon Redemption (Mailer)
Loyalty Coupon Redemption allows scanning a bar code coupon mailed to a customer. After scanning the bar
code, the screen indicates the discount the customer is entitled to on one item purchased using the loyalty
card. This demo shows that the coupon contains not only the discount information but also information that
uniquely identifies the customer.
Loyalty Coupon Redemption
(Mailer)
Figure D-5 Loyalty Coupon Redemption (Mailer)
Cell Phone Coupon
Cell Phone Coupon allows scanning a bar code coupon emailed to a customer’s phone. After scanning the
demo bar code below, the customer is prompted to scan the bar code on the cell phone. This redeems the
coupon and shows what the customer has earned on the loyalty account.
Cell Phone Coupon
Figure D-6 Cell Phone Coupon
D-4
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
Lottery Win Verification
Lottery Win Verification allows a customer to scan a lottery ticket to see if it is a winning ticket. This demo
displays a message on the screen and plays a voice message indicating that the ticket is a winning ticket.
Lottery Win Verification
Figure D-7 Lottery Win Verification
Employee Application
Employee Application demonstrates an employee management system. It allows an associate to scan a badge
to clock in, clock out, check task status, and check the schedule. On the My Tasks screen, the user can press
Restock End Caps to drill down and see more information. A simulated print also occurs from the My Tasks
screen or Schedule screen if the Print button is pressed.
Employee Application
Figure D-8 Employee Application
INDEX
Numerics
AC power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
accessing the Windows® CE desktop . . . . . . . . . . . 4-2
ActiveSync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5, 5-7
connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
downloading files . . . . . . . . . . . . . . . . . . . . . . . . 5-5
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
ad-hoc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6, B-43
Advanced Encryption Standard . . . . . . . . . . . . . . . B-20
advertisement insert . . . . . . . . . . . . . . . . . . . . . 2-9, 2-12
AES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-20
aiming
pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
AP networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-43
authentication
EAP-FAST . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
EAP-TLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
LEAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
none . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
PEAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15, C-2
CHAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-11
chapter descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
cold boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
ethernet, wired . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2, 2-3
wired ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
companion programs
internet explorer . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
media player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
wordpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
configuration file
downloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
to host computer . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
wired ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
country code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
cpf file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
creating via SCM . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
creating splash screen . . . . . . . . . . . . . . . . . . . . . . . 5-17
B
D
bar code scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
bluetooth
ad-hoc mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
DCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-xi, 5-1, 5-7
default gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-23
demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
deployment
file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
developer kits
104-Bit WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-20
40-Bit WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-19
802.11 ESSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
A
C
CAB files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Index - 2
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
EMDK for C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
EMDK for NET . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
PocketBrowser . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Device Configuration Package . . . . .3-xi, 5-1, 5-8, 5-11,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17, 5-18, 5-19
DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-23, B-24
download
configuration file . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
to host computer . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
G
E
I
EAP-FAST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
EAP-GTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-11
EAP-TLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
EMDK for C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
EMDK for Net . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
EMDKs
for C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
for NET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
PocketBrowser . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
encryption
open system . . . . . . . . . . . . . . . . . . . . . . B-19, B-23
TKIP (WPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . B-20
Enterprise Mobility Developer Kit for C . . . . . . . . . . . 5-1
Enterprise Mobility Developer Kit for Net . . . . . . . . . . 5-1
Enterprise Mobility Developer Kits (EMDKs) . . . . . . . 1-5
error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
ESSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
ethernet setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Bias-T port connection . . . . . . . . . . . . . . . . . . . . 1-3
wired . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
external ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
IE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
imaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
information, service . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
infrastructure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-6
input panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
installing
ActiveSync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
advertisment insert . . . . . . . . . . . . . . . . . . . 2-9, 2-12
connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
development tools . . . . . . . . . . . . . . . . . . . . . . . . 5-4
mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
pole mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
VESA mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
internet explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-24
IP config
DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-24
gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-24
IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-24
subnet mask . . . . . . . . . . . . . . . . . . . . . . . . . . .B-24
WINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-24
F
features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
file deployment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
file explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
flash file system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
downloading partitions . . . . . . . . . . . . . . . . . . . 5-19
non-FFS partitions . . . . . . . . . . . . . . . . . . . . . . 5-19
splash screen . . . . . . . . . . . . . . . . . . . . . . . 5-19
partitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
copyfile . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
regmerge . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
flash storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
font loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-24
H
headset jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
host communications
ethernet, wired . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
K
keyboard
virtual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
L
LEAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-10
loading fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
M
MD5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-11
media player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4, 4-5
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Index - 3
memory management . . . . . . . . . . . . . . . . . . . . . . . . 4-2
micro SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
inserting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
microsoft applications
internet explorer . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
media player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
wordpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Mobility Services Platform Console . . . . . . . . . . . . 5-17
mode
802.11 ESSID . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
ad-hoc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
infrastructure . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
profile name . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5, 2-5
pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
VESA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
MS CHAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-12
MS CHAP v2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-12
MSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
N
nonvolatile memory . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
notational conventions . . . . . . . . . . . . . . . . . . . . . . . . . x
NTP, see SNTP
POE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
ports
ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Ethernet/Bias-T . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
headset jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
RJ45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3, 2-3
power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
AC power supply . . . . . . . . . . . . . . . . . . . . . 1-4, 2-2
options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4, 2-2
POE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
power-over-ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
printer
connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
profile
create new . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-30
delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-30
edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-29
name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
program memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
programs
flash file system . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
R
O
open system . . . . . . . . . . . . . . . . . . . . . . . . . B-19, B-23
operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
operating system upgrade . . . . . . . . . . . . . . . . . . . . 5-7
OS upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
P
PAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-12
partitions
downloading . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
FFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
non-FFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
splash screen . . . . . . . . . . . . . . . . . . . . . . . 5-19
parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
PC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2, 4-4, C-3
access cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
PC download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
PCMCIA . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2, 4-4, C-3
access cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
PEAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
peripheral connection
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
PocketBrowser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
RAM memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
rapid deployment client . . . . . . . . . . . . . . . . . . . . . . 5-17
RD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
rebooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
recalibrate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
S
scan beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
bar code scanning . . . . . . . . . . . . . . . . . . . . . . . . 1-6
SCM
file deployment . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
file types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
parameter indicators . . . . . . . . . . . . . . . . . . . . . . 3-3
user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
XML provisioning . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
screen calibration . . . . . . . . . . . . . . . . . . . . . . . 5-15, C-2
screen protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Index - 4
MK4000 MicroKiosk for CE .NET 5.0 Product Reference Guide
scripts
creating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
SD card, micro . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4, C-3
inserting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
service information . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
setup
advertisement insert . . . . . . . . . . . . . . . . . .2-9, 2-12
inserting micro SD card . . . . . . . . . . . . . . . . . . . . 2-2
mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
pole mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
USB to host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
VESA mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
wired ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
wired ethernet AC outlet . . . . . . . . . . . . . . . . . . . 2-3
wired ethernet, POE . . . . . . . . . . . . . . . . . . . . . . 2-3
signal strength . . . . . . . . . . . . . . . . . . . . . . . . . B-3, B-35
Simple Network Time Protocol, see SNTP
SNTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
software developer kits
EMDK for C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
EMDK for NET . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
PocketBrowser . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
specular reflection . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
splash screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
creating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-23
storage memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
subnet mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-24
Symbol configuration manager
file deployment . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
file types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
parameter indicators . . . . . . . . . . . . . . . . . . . . . . 3-3
user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
XML provisioning . . . . . . . . . . . . . . . . . . . . . . . . 3-1
T
TCM
building hex image . . . . . . . . . . . . . . 5-8, 5-12, 5-13
creating script . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
defining properties . . . . . . . . . . . . . . . . . . . . . . 5-10
error messages . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
hex image download . . . . . . . . . . . . . . . . . . . . . 5-13
saving script . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
technical specifications . . . . . . . . . . . . . . . . . . . . . . . .A-1
time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
TKIP (WPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-20
TLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-12
touch screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-2
U
unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
updating data
time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
upgrade
OS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
USB
cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
communications . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
host connection . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
peripheral connection . . . . . . . . . . . . . . . . . . . . . . 2-3
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
V
virtual keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
volatile memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
W
WINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-23, B-24
wireless local area networks . . . . . . . . . . . . . . . . . . .B-2
wordpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
X
XML provisioning
SCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Tell Us What You Think...
We’d like to know what you think about this Manual. Please take a moment to fill out this questionnaire and fax this form
to: (631) 627-7184, or mail to:
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
Attention: Technical Publications Manager
Advanced Data Capture Division
IMPORTANT: If you need product support, please call the appropriate customer support number provided. Unfortunately,
we cannot provide customer support at the fax number above.
Manual Title:___________________________________________
(please include revision level)
How familiar were you with this product before using this manual?
Very familiar
Slightly familiar
Not at all familiar
Did this manual meet your needs? If not, please explain.
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
What topics need to be added to the index, if applicable?
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
What topics do you feel need to be better discussed? Please be specific.
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
What can we do to further improve our manuals?
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
Thank you for your input—We value your comments.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions
worldwide. All other trademarks are the property of their respective owners.
© 2015 ZIH Corp and/or its affiliates. All rights reserved.
72E-121864-05 Revision A - September 2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising