DEH-P7000UB - 130.com.ua
PHONES
(044) 360-7-130
(050) 336-0-130
(063) 788-0-130
(067) 233-0-130
(068) 282-0-130
Internet store of
autogoods
ICQ
294-0-130
597-0-130
SKYPE
km-130
CAR RECEIVERS — Receivers • Media receivers and stations • Native receivers • CD/DVD changers • FM-modulators/USB adapters • Flash memory • Facia plates and adapters • Antennas • Accessories |
CAR AUDIO — Car audio speakers • Amplifiers • Subwoofers • Processors • Crossovers • Headphones • Accessories | TRIP COMPUTERS — Universal computers • Model computers • Accessories |
GPS NAVIGATORS — Portable GPS • Built-in GPS • GPS modules • GPS trackers • Antennas for GPS navigators • Accessories | VIDEO — DVR • TV sets and monitors • Car TV tuners • Cameras • Videomodules
• Transcoders • Car TV antennas • Accessories | SECURITY SYSTEMS — Car alarms • Bike alarms • Mechanical blockers • Immobilizers • Sensors • Accessories | OPTIC AND LIGHT — Xenon • Bixenon • Lamps
• LED • Stroboscopes • Optic and Headlights • Washers • Light, rain sensors • Accessories | PARKTRONICS AND MIRRORS — Rear parktronics • Front parktronics • Combined parktronics • Rear-view mirrors
• Accessories | HEATING AND COOLING — Seat heaters • Mirrors heaters • Screen-wipers heaters • Engine heaters • Auto-refrigerators • Air conditioning units • Accessories | TUNING — Vibro-isolation
• Noise-isolation • Tint films • Accessories | ACCESSORIES — Radar-detectors • Handsfree, Bluetooth • Windowlifters • Compressors • Beeps, loudspeakers • Measuring instruments • Cleaners • Carsits
• Miscellaneous | MOUNTING — Installation kits • Upholstery • Grilles • Tubes • Cable and wire • Tools • Miscellaneous | POWER — Batteries • Converters • Start-charging equipment • Capacitors
• Accessories | MARINE AUDIO AND ELECTRONICS — Marine receivers • Marine audio speakers • Marine subwoofers • Marine amplifiers • Accessories | CAR CARE PRODUCTS — Additives • Washer fluid •
Care accessories • Car polish • Flavors • Adhesives and sealants | LIQUID AND OIL — Motor oil • Transmission oil • Brake fluid • Antifreeze • Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in
Kyiv and other cities, delivery by ground and postal services. Our experienced
consultants will provide you with exhaustive information and help you to chose
the very particular thing. We are waiting for you at the address
http://130.com.ua
Operation Manual
CD RDS RECEIVER
13
0.
co
m
.u
a
DEH-P7000UB
English
Autogood products «130»
Contents
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate
your model properly. After you have finished reading the instructions, keep this manual in a safe place for future reference.
.u
m
About this unit 5
Visit our website 6
In case of trouble 6
Protecting your unit from theft 6
– Removing the front panel 7
– Attaching the front panel 7
Resetting the microprocessor 7
About the demo mode 7
Use and care of the remote control 8
– Installing the battery 8
– Using the remote control 8
13
0.
co
Operating this unit
What’s What 9
– Head unit 9
– Remote control 10
Basic Operations 11
– Power ON/OFF 11
– Selecting a source 11
– Adjusting the volume 11
Tuner 12
– Basic Operations 12
– Storing and recalling broadcast
frequencies 12
– Receiving PTY alarm broadcasts 13
– Introduction of advanced
operations 13
– Storing the strongest broadcast
frequencies 13
– Tuning in strong signals 14
– Selecting alternative frequencies 14
– Receiving traffic announcements 15
– Using PTY functions 15
– Using radio text 16
– PTY list 17
Built-in CD Player 18
– Basic Operations 18
– Selecting a track directly 19
2
– Displaying text information on disc 19
– Selecting tracks from the track title
list 20
– Selecting files from the file name
list 20
– Introduction of advanced
operations 20
– Selecting a repeat play range 20
– Playing tracks in random order 21
– Scanning folders and tracks 21
– Pausing playback 21
– Using Sound Retriever 21
– Using disc title functions 21
Playing songs on USB portable audio player/
USB memory 23
– Basic Operations 23
– Selecting an audio file directly in the
current folder 23
– Displaying text information of an audio
file 23
– Selecting files from the file name
list 23
– Introduction of advanced
operations 24
Playing songs on iPod 25
– Basic Operations 25
– Browsing for a song 25
– Displaying text information on
iPod 26
– Introduction of advanced
operations 26
– Playing songs in a random order
(shuffle) 27
– Playing all songs in a random order
(shuffle all) 27
– Selecting songs from album list of
currently playing artist 27
– Operating this unit’s iPod function
from your iPod 27
a
Before You Start
En
Autogood products «130»
Contents
a
co
m
Audio Adjustments
Introduction of audio adjustments 29
Using balance adjustment 29
Using the equalizer 29
– Recalling equalizer curves 29
– Adjusting equalizer curves 30
– Adjusting 7-band graphic equalizer 30
Adjusting loudness 31
Using subwoofer output 31
– Adjusting subwoofer settings 31
Boosting the bass 32
Using the high pass filter 32
Adjusting source levels 32
Using automatic sound levelizer 33
Other Functions
Using the AUX source 40
– About AUX1 and AUX2 40
– AUX1 source: 40
– AUX2 source: 40
– Selecting AUX as the source 40
– Setting the AUX title 40
Using the external unit 40
– Selecting the external unit as the
source 40
– Basic operation 41
– Using the functions allocated to 1 to 6
keys 41
– Advanced operations 41
Using different entertainment displays 41
Using the PGM button 41
.u
– Changing audiobook speed 28
13
0.
Initial Settings
Adjusting initial settings 34
Selecting the display language 34
Setting the date 34
Setting the clock 35
Turning the off clock display on or off 35
Setting the FM tuning step 35
Switching Auto PI Seek 36
Switching the warning tone 36
Switching the face auto open 36
Switching the auxiliary setting 36
Switching the dimmer setting 36
Adjusting the brightness 37
Setting the rear output and subwoofer
controller 37
Switching the sound muting/attenuation 37
Switching the feature demo 38
Switching the reverse mode 38
Switching the ever scroll 38
Activating the BT Audio source 38
Entering PIN code for Bluetooth wireless
connection 39
Displaying system version for repair 39
Available accessories
Playing songs on iPod 43
– Basic operation 43
– Displaying text information on
iPod 43
– Browsing for a song 43
– Introduction of advanced
operations 43
– Playing songs in a random order
(shuffle) 44
Bluetooth Audio 44
– Basic Operations 44
– Function and operation 45
– Connecting a Bluetooth audio
player 45
– Playing songs on Bluetooth audio
player 46
– Stopping playback 46
– Disconnecting a Bluetooth audio
player 46
– Displaying BD (Bluetooth Device)
address 46
Bluetooth Telephone 46
En
Autogood products «130»
3
Contents
–
–
–
–
–
–
–
–
– Basic Operations 60
– Storing and recalling broadcast
stations 61
– Storing the strongest broadcast
stations sequentially 61
.u
a
Additional Information
Error messages 63
Handling guideline of discs and player 64
Dual Discs 65
Compressed audio compatibility 65
USB audio player/USB memory 65
– USB audio player/USB memory
compatibility 65
– Handling guideline and supplemental
information 66
iPod 67
– About handling the iPod 67
– About iPod settings 67
Compressed audio files on the disc 67
– Example of a hierarchy 68
Specifications 69
13
0.
co
m
Basic Operations 46
Setting up for hands-free phoning 47
Making a phone call 48
Taking a phone call 48
Function and operation 48
Connecting a cellular phone 49
Disconnecting a cellular phone 50
Registering a connected cellular
phone 50
– Deleting a registered phone 50
– Connecting to a registered cellular
phone 51
– Using the phone book 51
– Using the call history 53
– Using preset numbers 53
– Making a call by entering phone
number 54
– Clearing memory 54
– Setting automatic rejecting 54
– Setting automatic answering 55
– Switching the ring tone 55
– Echo canceling and noise
reduction 55
Multi-CD Player 55
– Basic Operations 55
– Using CD TEXT functions 55
– Introduction of advanced
operations 56
– Using compression and bass
emphasis 56
– Using ITS playlists 57
– Using disc title functions 58
DVD Player 59
– Basic Operations 59
– Selecting a disc 59
– Selecting a folder 59
– Introduction of advanced
operations 59
TV tuner 60
4
En
Autogood products «130»
Section
Before You Start
01
.u
a
About WMA
The Windows Media™ logo printed on the box
indicates that this unit can play back WMA
data.
Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft
Corporation in the United States and/or other
countries.
! This unit may not operate correctly depending on the application used to encode
WMA files.
About this unit
0.
co
m
Private households in the member states of
the EU, in Switzerland and Norway may return
their used electronic products free of charge
to designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please
contact your local authorities for the correct
method of disposal.
By doing so you will ensure that your disposed
product undergoes the necessary treatment,
recovery and recycling and thus prevent potential negative effects on the environment
and human health.
Before You Start
If you want to dispose this product, do not mix
it with general household waste. There is a separate collection system for used electronic
products in accordance with legislation that requires proper treatment, recovery and recycling.
! The Pioneer CarStereo-Pass is for use only in
Germany.
! Keep this manual handy as a reference for operating procedures and precautions.
! Always keep the volume low enough so that
you can hear sounds from outside the vehicle.
! Protect this unit from moisture.
! If the battery is disconnected or discharged,
the preset memory will be erased and must be
reprogrammed.
13
The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the
Middle East, Africa and Oceania. Use in other
areas may result in poor reception. The RDS
(radio data system) function operates only in
areas with FM stations broadcasting RDS signals.
CAUTION
! Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and overheating could result from contact with liquids.
! “CLASS 1 LASER PRODUCT”
This product contains a laser diode of higher
class than 1. To ensure continued safety, do
not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.
About MP3
Supply of this product only conveys a license
for private, non-commercial use and does not
convey a license nor imply any right to use
this product in any commercial (i.e. revenuegenerating) real time broadcasting (terrestrial,
satellite, cable and/or any other media), broadcasting/streaming via internet, intranets and/
or other networks or in other electronic content distribution systems, such as pay-audio or
audio-on-demand applications. An independent license for such use is required. For details, please visit
http://www.mp3licensing.com.
About AAC
This unit plays back AAC files encoded by
iTunes®.
iTunes is a trademark of Apple Inc., registered
in the U.S. and other countries.
En
Autogood products «130»
5
Section
Before You Start
Visit our website
Visit us at the following site:
http://www.pioneer.co.uk
! Register your product. We will keep the details of your purchase on file to help you
refer to this information in the event of an
insurance claim such as loss or theft.
! We offer the latest information about
Pioneer Corporation on our website.
m
iPod® compatibility
This unit can control and listen to songs on an
iPod.
! This unit supports only an iPod with Dock
Connector.
! This unit supports only the following iPods.
Supported iPod software versions are
shown below. Older versions of iPod software may not be supported.
— iPod fifth generation (software version
1.2.1)
— iPod nano first generation (software version 1.3.1)
— iPod nano second generation (software
version 1.1.3)
— iPod nano third generation (software
version 1.0.2)
— iPod classic (software version 1.0.2)
— iPod touch (software version 1.1.1)
For maximum performance, we recommend that you use the latest version of the
iPod software.
! Operations may vary depending on the software version of iPod.
! When using an iPod, iPod Dock Connector
to USB Cable is required.
! Pioneer CD-IU50 interface cable is also
available. For details, consult your dealer.
! This unit can control previous generations
iPod models with a Pioneer iPod adapter
(e.g. CD-IB100N).
For details concerning operation with the
iPod adapter, refer to Playing songs on iPod
on page 43.
! iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
CAUTION
! Pioneer accepts no responsibility for data lost
on the USB portable audio player/USB memory even if that data is lost while using this
unit.
! Pioneer accepts no responsibility for data lost
on the iPod even if that data is lost while
using this unit.
a
Portable audio player compatibility
! Inquire at the manufacturer about your
USB portable audio player/USB memory.
This unit corresponds to the following.
— USB MSC (Mass Storage Class) compliant
portable audio player and memory
— WMA, MP3, AAC and WAV file playback
For details about the compatibility, refer to
USB audio player/USB memory compatibility
on page 65.
.u
01
13
0.
co
In case of trouble
6
Should this product fail to operate properly,
contact your dealer or nearest authorized
Pioneer Service Station.
Protecting your unit from
theft
The front panel can be detached to deter theft.
! If the front panel is not detached from the
head unit within five seconds of turning off
the ignition, a warning tone sounds.
! You can turn off the warning tone. See
Switching the warning tone on page 36.
! You can turn off the face auto open. See
Switching the face auto open on page 36.
Important
! Handle gently when removing or attaching
the front panel.
! Avoid subjecting the front panel to excessive
shock.
En
Autogood products «130»
Section
Before You Start
01
2 Replace the front panel by clipping it
into place.
Before You Start
! Keep the front panel out of direct sunlight and
high temperatures.
! A few seconds after turning the ignition
switch to on or off, the front panel automatically moves. When this happens, your fingers
may become jammed in the panel, so keep
your hands away from it.
Removing the front panel
1 Press and hold OPEN to open the front
panel.
Resetting the microprocessor
m
% Press RESET with a pen tip or other
pointed instrument.
13
0.
co
2 Slide and remove the front panel toward you.
Take care not to grip it too tightly or to drop
the front panel and protect it from contact
with water or other fluids to prevent permanent damage.
.u
a
The microprocessor must be reset under the
following conditions:
! Prior to using this unit for the first time
after installation
! If the unit fails to operate properly
! When strange or incorrect messages appear on the display
3 Put the front panel into the provided
protective case for safe keeping.
RESET button
Attaching the front panel
About the demo mode
1
This unit features two demonstration modes.
One is the reverse mode, the other is the feature demo mode.
Make sure the inner cover is closed.
Important
The red lead (ACC) of this unit should be connected to a terminal coupled with ignition switch
on/off operations. If this is not done, the vehicle
battery may be drained.
En
Autogood products «130»
7
Section
Before You Start
Feature demo mode
The feature demo automatically starts when
power to this unit is turned off while the ignition switch is set to ACC or ON. Press DISP
during feature demo operation to cancel the
feature demo mode. Press DISP again to start.
Remember that if the feature demo continues
operating when the car engine is turned off, it
may drain battery power.
Using the remote control
Point the remote control in the direction of the
front panel to operate.
! The remote control may not function properly in direct sunlight.
Important
m
Use and care of the remote
control
! There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the
same or equivalent type.
! Do not handle the battery with metallic tools.
! Do not store the battery with metallic objects.
! If the battery leaks, wipe the remote control
completely clean and install a new battery.
! When disposing of used batteries, comply
with governmental regulations or environmental public institutions’ rules that apply in your
country/area.
a
Reverse mode
If you do not perform an operation within
about 30 seconds, screen indications start to
reverse, and then continue reversing every 10
seconds. Pressing BAND when power to this
unit is turned off while the ignition switch is
set to ACC or ON cancels the reverse mode.
Press BAND again to start the reverse mode.
.u
01
co
Installing the battery
! Do not store the remote control in high temperatures or direct sunlight.
! Do not let the remote control fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
13
0.
Slide the tray on the back of the remote control out and insert the battery with the plus (+)
and minus (–) poles aligned properly.
! When using for the first time, pull out the
film protruding from the tray.
WARNING
Keep the battery out of the reach of children.
Should the battery be swallowed, consult a doctor immediately.
CAUTION
! Use one CR2025 (3 V) lithium battery.
! Remove the battery if the remote control is not
used for a month or longer.
8
En
Autogood products «130»
Section
Operating this unit
02
a
Operating this unit
7 LIST button
Press to display the disc title list, track title
list, folder list, file list or preset channel list
depending on the source.
.u
What’s What
m
Head unit
8 TA/NEWS button
Press to turn TA function on or off. Press
and hold to turn NEWS function on or off.
co
1 SRC/OFF button
This unit is turned on by selecting a source.
Press to cycle through all the available
sources.
0.
2 DISP/SCROLL button
Press to select different displays.
Press and hold to scroll the text information.
9 MUTE button
Press to turn off the sound. To turn on the
sound, press again.
6 EJECT/OPEN button
Press to eject a CD from your built-in CD
player.
Press and hold to open or close the front
panel.
b BAND/ESC button
Press to select among three FM bands and
MW/LW bands.
Press to return to the ordinary display when
operating menu.
13
5 RESET button
Press to reset the microprocessor.
a RDM/
/iPod button
Press to turn random function on or off
while using CD or USB.
While using iPod, press this button to shuffle all tracks.
Press and hold to switch the control mode
while using an iPod connected USB connector of this unit.
If using the iPod with an interface adapter
(CD-IB100N), press to switch the shuffle
function.
3 MULTI-CONTROL
Move to perform manual seek tuning, fast
forward, reverse and track search controls.
Also used for controlling functions.
Turn to increase or decrease the volume.
4 S.Rtrv button
Press to switch Sound Retriever settings.
En
Autogood products «130»
9
Section
02
Operating this unit
Remote control
Operation is the same as when using the buttons on the head unit.
l AUDIO button
Press to select various sound quality controls.
c VOLUME buttons
Press to increase or decrease the volume.
.u
m
e Thumb pad
Move to perform manual seek tuning, fast
forward, reverse and track search controls.
Also used for controlling functions.
Functions are the same as
MULTI-CONTROL except for volume control.
Press to display the disc title list, track title
list, folder list, file list or preset channel list
depending on the source.
a
d FUNCTION button
Press to select functions.
co
f DIRECT button
Press to directly select the desired track.
0.
g CLEAR button
Press to cancel the input number when 0 to
9 are used.
13
h 0 to 9 buttons
Press to directly select the desired track,
preset tuning or disc. Buttons 1 to 6 can operate the preset tuning for the tuner or disc
number search for the multi-CD player.
i PGM button
Press to operate the preprogrammed functions for each source. (Refer to Using the
PGM button on page 41.)
j MUTE button
Press to turn off the sound. To turn on the
sound, press again.
k ENT button
Press to change to the entertainment display.
10
En
Autogood products «130»
Section
Operating this unit
02
% Press SRC to turn the unit on.
Turning the unit off
% Press OFF and hold until the unit turns
off.
Selecting a source
You can select a source you want to listen to.
To switch to the built-in CD player, load a disc
in the unit (refer to page 18).
% Turn MULTI-CONTROL to adjust the
sound level.
0.
Notes
co
m
% Press SRC repeatedly to switch between the following sources.
Tuner—Television—DVD player/MultiDVD player—Built-in CD player—MultiCD player—iPod—USB—External unit 1—
External unit 2—AUX1—AUX2—BT Audio
—BT Telephone
Adjusting the volume
a
Turning the unit on
Operating this unit
Power ON/OFF
! External unit refers to a Pioneer product (such
as ones available in the future) that, although
incompatible as a source, enables control of
basic functions with this unit. Two external
units can be controlled with this unit. When
two external units are connected, the external
unit is automatically allocated to external unit
1 or external unit 2 by this unit.
! When this unit’s blue/white lead is connected
to the vehicle’s auto-antenna relay control
terminal, the vehicle’s antenna extends when
this unit’s source is turned on. To retract the
antenna, turn the source off.
.u
Basic Operations
13
! In the following cases, the sound source will
not change.
— When no unit corresponding to the selected source is connected.
— When there is no disc or magazine in the
player.
— When the iPod is not connected to this
unit.
— When AUX (auxiliary input) is set to off
(refer to page 36).
— When the BT Audio source is set to off
(refer to Activating the BT Audio source on
page 38).
! AUX1 is set to on by default. Turn off the AUX1
when not in use (refer to Switching the auxiliary setting on page 36).
! Charging the portable audio player using
car’s DC power source while connecting it to
AUX input may generate noise. In this case,
stop charging.
En
Autogood products «130»
11
Section
02
Operating this unit
4 Preset number indicator
5 Signal level indicator
Shows the radio wave strength.
6 Frequency indicator
Tuner
Basic Operations
RDS
% Select a band
Press BAND.
# Band can be selected from among FM1, FM2,
FM3 or MW/LW.
% Manual tuning (step by step)
Push MULTI-CONTROL left or right.
# You can cancel seek tuning by pushing
MULTI-CONTROL left or right.
# If you push and hold MULTI-CONTROL left or
right, you can skip stations. Seek tuning starts as
soon as you release MULTI-CONTROL.
m
1 Band indicator
2 5 (stereo) indicator
Appears when the selected frequency is being
broadcast in stereo.
3 Preset number indicator
4 Signal level indicator
Shows the radio wave strength.
5 TP ( ) indicator
Appears when a TP station is tuned in.
6 News ( ) indicator
Appears when the set news program is received.
7 Program service name
8 PTY label indicator
9 TEXT indicator
Shows when the radio text is received.
% Seek tuning
Push and hold MULTI-CONTROL left or right
for about one second and release.
a
.u
13
0.
co
Notes
Non-RDS or MW/LW
! This unit’s AF (alternative frequencies search)
function can be turned on and off. AF should
be off for normal tuning operation (refer to
page 14).
! RDS service may not be provided by all stations.
! RDS functions such as AF and TA are only active when your radio is tuned to an RDS station.
Storing and recalling broadcast
frequencies
You can easily store up to six broadcast frequencies for later recall.
! Six stations for each band can be stored in
memory.
1 Band indicator
2 5 (stereo) indicator
Appears when the selected frequency is being
broadcast in stereo.
3 LOC indicator
Appears when local seek tuning is on.
12
1 Press LIST.
Preset screen is displayed.
En
Autogood products «130»
Section
Operating this unit
02
3 Use MULTI-CONTROL to select the desired station.
Turn to change the station. Press to select.
1 Press MULTI-CONTROL to display the
main menu.
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
The function menu is displayed.
3 Turn MULTI-CONTROL to select the
function.
BSM (best stations memory)—Regional (regional)—Local (local seek tuning)—
PTY search (program type selection)—
Traffic Announce (traffic announcement
standby)—Alternative FREQ (alternative frequencies search)—News interrupt (news
program interruption)
Using the remote control
m
% When you find a frequency that you
want to store in memory, press one of preset tuning buttons 1 to 6 and hold until the
preset number stops flashing.
The number you have pressed will flash in the
preset number indicator and then remain lit.
The selected radio station frequency has been
stored in memory.
The next time you press the same preset tuning button the radio station frequency is recalled from memory.
.u
a
# You can also change the station by pushing
MULTI-CONTROL up or down.
# To return to the ordinary display, press BAND
or LIST.
# If you do not operate the list within about 30
seconds, the display automatically returns to the
ordinary display.
Introduction of advanced
operations
Operating this unit
2 Use MULTI-CONTROL to store the selected frequency in memory.
Turn to change the preset number. Press and
hold to store.
13
0.
co
Notes
# You can also recall radio station frequencies
assigned to preset tuning numbers by pushing
MULTI-CONTROL up or down during the frequency display.
Receiving PTY alarm broadcasts
When the emergency PTY code broadcasts,
the unit receives it automatically (ALARM appears). When the broadcasting ends, the system returns to the previous source.
! An emergency announcement can be canceled by pressing TA.
! You can also select the function by pressing
FUNCTION on the remote control.
! To return to the ordinary display, press BAND.
! If MW/LW band is selected, you can only select BSM or Local.
Storing the strongest broadcast
frequencies
BSM (best stations memory) lets you automatically store the six strongest broadcast frequencies.
1 Display the function menu.
Refer to Introduction of advanced operations on
this page.
2 Use MULTI-CONTROL to select BSM in
the function menu.
3 Press MULTI-CONTROL to turn BSM on.
The six strongest broadcast frequencies are
stored in the order of their signal strength.
# To cancel, press MULTI-CONTROL again.
En
Autogood products «130»
13
Section
Operating this unit
02
Tuning in strong signals
Local seek tuning lets you tune in only those
radio stations with sufficiently strong signals
for good reception.
1 Display the function menu.
Refer to Introduction of advanced operations on
the previous page.
data for the station received differs from that
of the originally stored station.
! During AF search, sound may be temporarily
interrupted.
! AF can be turned on or off independently for
each FM band.
Using PI Seek
# To turn local seek tuning off, press
MULTI-CONTROL again.
Using Auto PI Seek for preset stations
.u
When preset stations cannot be recalled, the
unit can be set to perform PI Seek during preset recall.
! The default setting for Auto PI Seek is off.
See Switching Auto PI Seek on page 36.
co
m
4 Push MULTI-CONTROL left or right to
set the sensitivity.
FM: Level 1—Level 2—Level 3—Level 4
MW/LW: Level 1—Level 2
The Level 4 setting allows reception of only
the strongest stations, while lower settings let
you receive progressively weaker stations.
a
3 Press MULTI-CONTROL to turn local
seek tuning on.
If the tuner cannot find a suitable station, or
reception status becomes bad, the unit automatically searches for a different station with
the same programming. During the search,
PI seek is displayed and the output is muted.
2 Use MULTI-CONTROL to select Local in
the function menu.
0.
Selecting alternative frequencies
13
When the tuner cannot get a good reception,
the unit automatically searches for a different
station in the same network.
1 Display the function menu.
Refer to Introduction of advanced operations on
the previous page.
2 Use MULTI-CONTROL to select
Alternative FREQ in the function menu.
3
Press MULTI-CONTROL to turn AF on.
# To turn off, press MULTI-CONTROL again.
When AF is used, the regional function limits
the selection of stations broadcasting regional
programs.
1 Display the function menu.
Refer to Introduction of advanced operations on
the previous page.
2 Use MULTI-CONTROL to select Regional
in the function menu.
3 Press MULTI-CONTROL to turn the regional function on.
# To turn off, press MULTI-CONTROL again.
Notes
Notes
! Only RDS stations are tuned in during seek
tuning or BSM when AF is on.
! When you recall a preset station, the tuner
may update the preset station with a new frequency from the station’s AF list. No preset
number appears on the display if the RDS
14
Limiting stations to regional
programming
! Regional programming and regional networks
are organized differently depending on the
country (i.e., they may change according to
the hour, state or broadcast area).
En
Autogood products «130»
Section
Operating this unit
02
TA (traffic announcement standby) lets you receive traffic announcements automatically, no
matter what source you are listening to. TA
can be activated for both a TP station (a station that broadcasts traffic information) or an
enhanced other network’s TP station (a station
carrying information which cross-references
TP stations).
You can tune in a station by using PTY (program type) information.
Searching for an RDS station by PTY
information
You can search for general types of broadcasting programs, such as those listed on page
17.
1 Display the function menu.
Refer to Introduction of advanced operations on
page 13.
.u
1 Tune in a TP or enhanced other network’s TP station.
The TP ( ) indicator will light.
Using PTY functions
a
Receiving traffic announcements
! Only TP and enhanced other network’s TP stations are tuned in during seek tuning or BSM
when TA is on.
Operating this unit
! The preset number may disappear from the
display if the tuner tunes in a regional station
which differs from the originally set station.
! The regional function can be turned on or off
independently for each FM band.
m
2 Use MULTI-CONTROL to select
PTY search in the function menu.
# To turn off, press TA again.
3 Push MULTI-CONTROL left or right to
select a program type.
News&Inf—Popular—Classics—Others
co
2 Press TA to turn traffic announcement
standby on.
13
0.
3 Use MULTI-CONTROL to adjust the TA
volume when a traffic announcement begins.
The newly set volume is stored in memory and
recalled for subsequent traffic announcements.
4 Press TA while a traffic announcement
is being received to cancel the announcement.
The tuner returns to the original source but remains in the standby mode until TA is pressed
again.
Notes
! You can also turn this function on or off in the
menu that appears by using
MULTI-CONTROL.
! The system switches back to the original
source following traffic announcement reception.
4 Press MULTI-CONTROL to begin the
search.
The unit searches for a station broadcasting
that program type. When a station is found, its
program service name is displayed.
PTY (program type ID code) information is
listed on page 17.
# To cancel the search, press MULTI-CONTROL
again.
# The program of some stations may differ from
that indicated by the transmitted PTY.
# If no station is broadcasting the type of program you searched for, Not found is displayed
for about two seconds and then the tuner returns
to the original station.
En
Autogood products «130»
15
Section
Operating this unit
Using news program interruption
When a news program is broadcast from a
PTY code news station, the unit automatically
switches to the news broadcast station. When
the news program ends, reception of the previous program resumes.
% Press NEWS and hold to turn on news
program interruption.
Press NEWS until NEWS ON appears in the
display.
# If there is no radio text data in memory the display will not change.
3 Push MULTI-CONTROL up or down to
scroll.
Push MULTI-CONTROL up to go to the beginning. Push MULTI-CONTROL down to scroll
the radio text data.
Storing and recalling radio text
a
# To turn off news program interruption, press
NEWS and hold until OFF appears in the display.
# A news program can be canceled by pressing
NEWS.
2 Push MULTI-CONTROL left or right to
recall the three most recent radio texts.
Pushing MULTI-CONTROL left or right
switches between the current and the three
radio text data displays.
Note
1 Display the radio text you want to
store in memory.
Refer to Displaying radio text on this page.
m
You can also turn on or off news programs in the
menu that appears by using MULTI-CONTROL.
You can store data from up to six radio text
transmissions for buttons 1 to 6 on the remote
control.
.u
02
co
Using radio text
13
0.
This tuner can display radio text data transmitted by RDS stations, such as station information, the name of the currently broadcast
song and the name of the artist.
! The tuner automatically memorizes the
three latest radio text broadcasts received,
replacing text from the least recent reception with new text when it is received.
2 Press and hold any buttons 1 to 6 on
the remote control to store the selected
radio text.
The memory number will display and the selected radio text will be stored in memory.
The next time you press the same button on
the remote control in the radio text display the
stored text is recalled from memory.
Displaying radio text
You can display the currently received radio
text and the three most recent radio texts.
1 Press DISP and hold to display radio
text.
Radio text for the currently broadcasting station is displayed.
# You can cancel radio text display by pressing
DISP or BAND.
# When no radio text is received, No text appears in the display.
16
En
Autogood products «130»
Section
Operating this unit
02
PTY list
Others
Educational programs
Radio plays and serials
CULTURE
National or regional culture
SCIENCE
Nature, science and
technology
VARIED
Light entertainment
CHILDREN
Children’s
SOCIAL
Social affairs
Specific
Type of program
News&Inf
NEWS
News
AFFAIRS
Current affairs
INFO
General information and
advice
SPORT
Sports
WEATHER
Weather reports/meteorological information
FINANCE
Stock market reports,
commerce, trading, etc.
RELIGION
Religious affairs or services
POP MUS
Popular music
PHONE IN
Phone in
ROCK MUS
Contemporary modern
music
TOURING
Travel programs; not for
traffic announcements
EASY MUS
Easy listening music
OTH MUS
Non-categorized music
JAZZ
Jazz
COUNTRY
Country music
NAT MUS
National music
OLDIES
Oldies, golden oldies
.u
m
DOCUMENT
Documentaries
co
Hobbies and recreational activities
FOLK MUS
Folk music
L. CLASS
Light classical music
CLASSIC
Classical music
0.
Classics
LEISURE
13
Popular
a
General
Operating this unit
EDUCATE
DRAMA
En
Autogood products «130»
17
Section
02
Operating this unit
% Select a folder
Push MULTI-CONTROL up or down.
Built-in CD Player
Basic Operations
1
2
# You cannot select a folder that does not have
a compressed audio file recorded in it.
3
% Select a track
Push MULTI-CONTROL left or right.
% Fast forward or reverse
Push and hold MULTI-CONTROL left or right.
# When playing compressed audio, there is no
sound on fast forward or reverse.
% Return to root folder
Press and hold BAND.
# If folder 01 (ROOT) contains no files, playback
commences with folder 02.
% Switch between compressed audio and
CD-DA
Press BAND.
m
1 WMA/MP3/AAC/WAV indicator
Shows the type of audio file currently playing
when the compressed audio is playing.
2 Folder number indicator
Shows the folder number currently playing
when the compressed audio is playing.
3 Track number indicator
4 Play time indicator
5 Bit rate/sampling frequency indicator
Shows the bit rate or sampling frequency of
the current track (file) when the compressed
audio is playing.
a
4
.u
5
co
# This operation is available only when playing
CD-EXTRA or MIXED-MODE CDs.
# If you have switched between compressed
audio and CD-DA, playback starts at the first
track on the disc.
13
0.
! When playing back VBR (variable bit
rate)-recorded WMA files, the average
bit rate value is displayed.
! When playing back VBR (variable bit
rate)-recorded MP3 files, VBR is displayed instead of bit rate value.
% Open the front panel
Press EJECT.
Disc loading slot appears.
Disc loading slot
# When loading a disc, face the label side of
a disc up.
% Eject a disc
Press EJECT.
18
Notes
! The built-in CD player can play back audio CD
and compressed audio recorded on a CDROM. (Refer to page 67 for files that can be
played back.)
! Read the precautions for discs and player on
page 64.
! After a disc has been inserted, press SRC to
select the built-in CD player.
! There is sometimes a delay between starting
up disc playback and the sound being issued.
When being read, FORMAT READ is displayed.
! If an error message is displayed, refer to Error
messages on page 63.
! Playback is carried out in order of file number.
Folders are skipped if they contain no files. (If
folder 01 (ROOT) contains no files, playback
commences with folder 02.)
En
Autogood products «130»
Section
Operating this unit
02
1 Press DIRECT.
Track number input display appears.
2 Press 0 to 9 buttons to enter the desired
track number.
3 Press DIRECT.
The track for the entered number will play.
! You can scroll to the left of the title by pressing
and holding DISP.
! Audio CD that contains certain information
such as text and/or number is CD TEXT.
! If specific information is not recorded on a
disc, title or name is not displayed.
! Depending on the version of iTunes® used to
write MP3 files onto a disc, comment information may not be correctly displayed.
! Depending on the version of Windows Media
Player used to encode WMA files, album
names and other text information may not be
correctly displayed.
! When playing back VBR (variable bit rate)-recorded WMA files, the average bit rate value is
displayed.
! When playing back VBR (variable bit rate)-recorded MP3 files, VBR is displayed instead of
bit rate value.
! The sampling frequency shown in the display
may be abbreviated.
! When Ever Scroll is set to ON at the initial setting, text information scrolls continuously in
the display. Refer to Switching the ever scroll
on page 38.
! Depending on the character sets in the disc,
Russian texts may be garbled. About the allowed character sets for Russian texts, refer to
Compressed audio files on the disc on page 67.
m
# You can cancel the input number by pressing
CLEAR.
Notes
a
When using the remote control, you can select
a track directly by entering the desired track
number.
! When audio files are being played back,
you can select track in the current folder.
.u
Selecting a track directly
time— : track title, : artist name and
: album title
! For WAV
Play time— : folder name and : file
name
Operating this unit
! You can eject the CD by pressing and holding
EJECT with eject position when the CD loading or ejecting cannot operate properly.
0.
co
# After entering the number input mode, if you
do not perform an operation within about eight
seconds, the mode is automatically canceled.
13
Displaying text information on
disc
% Press DISP to select the desired text information.
! For title entered CD
Play time— : disc title and play time
! For CD TEXT discs
Play time— : disc artist name and :
track title— : disc artist name and :
disc title— : disc title and : track title
— : track artist name and : track title
— : track title and play time— : track
title, : track artist name and : disc title
! For WMA/MP3/AAC
Play time— : folder name and : file
name— : artist name and : track title
— : artist name and : album title— :
album title and : track title— : track
title and play time— : comment and play
En
Autogood products «130»
19
Section
Operating this unit
1 Press LIST to switch to the track title list
mode.
# Number of the folders/files in the currently selected folder will be indicated on the right side of
the display.
# To return to the ordinary display, press BAND
or LIST.
# If you do not operate the list within about 30
seconds, the display automatically returns to the
ordinary display.
2 Use MULTI-CONTROL to select the desired track title.
Turn to change the track title. Press to play.
Introduction of advanced
operations
Track title list lets you see the list of track titles
on a CD TEXT disc and select one of them to
play back.
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
The function menu is displayed.
3 Turn MULTI-CONTROL to select the
function.
Play mode (repeat play)—Random mode
(random play)—Scan mode (scan play)—
Pause (pause)—Sound Retriever (sound retriever)—TitleInput "A" (disc title input)
co
Selecting files from the file
name list
1 Press MULTI-CONTROL to display the
main menu.
m
# You can also change the track title by pushing
MULTI-CONTROL up or down.
# To return to the ordinary display, press BAND
or LIST.
# If you do not operate the list within about 30
seconds, the display automatically returns to the
ordinary display.
a
Selecting tracks from the track
title list
.u
02
0.
File name list lets you see the list of file names
(or folder names) and select one of them to
playback.
13
1 Press LIST to switch to the file name list
mode.
Names of files and folders appear in the display.
2 Use MULTI-CONTROL to select the desired file name (or folder name).
Turn to change the name of file or folder.
— when a file is selected, press to play.
— when a folder is selected, press to see a list
of files (or folders) in the seleted folder.
— when a folder is selected, press and hold to
play a song in the selected folder.
# You can also play the file by pushing
MULTI-CONTROL right.
# You can also play a song in the selected folder
by pushing and holding MULTI-CONTROL right.
# To return to the previous list (the folder one
level higher), push MULTI-CONTROL left.
20
Notes
! You can also select the function by pressing
FUNCTION on the remote control.
! To return to the ordinary display, press BAND.
! If you do not operate functions except for
TitleInput "A" within about 30 seconds, the
display automatically returns to the ordinary
display.
! When playing a compressed audio disc or CD
TEXT disc, you cannot switch to disc title input
display.
Selecting a repeat play range
1 Display the function menu.
Refer to Introduction of advanced operations on
this page.
En
Autogood products «130»
Section
Operating this unit
02
4 When you find the desired track press
MULTI-CONTROL to turn scan play off.
Playing tracks in random order
0.
# To turn random play off, press RDM again.
Note
2 Use MULTI-CONTROL to select Pause in
the function menu.
3 Press MULTI-CONTROL to turn pause
on.
Playback of the current track pauses.
# To turn pause off, press MULTI-CONTROL
again.
co
% Press RDM to turn random play on.
Tracks play in a random order.
1 Display the function menu.
Refer to Introduction of advanced operations on
the previous page.
m
Tracks in a selected repeat range are played in
random order.
Pausing playback
a
! Disc repeat – Repeat all tracks
! Track repeat – Repeat the current track
! Folder repeat – Repeat the current folder
# If you select another folder during repeat play,
the repeat play range changes to disc repeat.
# Performing track search or fast forward/reverse during Track repeat (track repeat) changes
the repeat play range to disc/folder.
# When Folder repeat (folder repeat) is selected, it is not possible to play back a subfolder
of that folder.
# If the display has automatically returned to
the playback display, select Scan mode again by
using MULTI-CONTROL.
# After scanning of a disc (folder) is finished,
normal playback of the tracks begins.
Operating this unit
3 Press MULTI-CONTROL to select the repeat range.
.u
2 Use MULTI-CONTROL to select
Play mode in the function menu.
13
You can also turn this function on or off in the
menu that appears by using MULTI-CONTROL.
Scanning folders and tracks
Scan play searches the song within the selected repeat range.
Using Sound Retriever
Sound Retriever function automatically enhances compressed audio and restores rich
sound.
% Press S.Rtrv repeatedly to select the desired setting.
OFF (off)—1—2
# 2 is more effective than 1.
Note
1 Display the function menu.
Refer to Introduction of advanced operations on
the previous page.
You can also perform this operation in the menu
that appears by using MULTI-CONTROL.
2 Use MULTI-CONTROL to select
Scan mode in the function menu.
Using disc title functions
3 Press MULTI-CONTROL to turn scan play
on.
The first 10 seconds of each track is played.
You can input CD titles and display the title.
The next time you insert a CD for which you
have entered a title, the title of that CD is displayed.
En
Autogood products «130»
21
Section
02
Operating this unit
Entering disc titles
Use the disc title input feature to store up to
48 CD titles in the unit. Each title can be up to
10 characters long.
! If you connect a multi-CD player, you can
input disc titles for up to 100 discs.
! When a multi-CD player that does not support
disc title functions is connected, you cannot
enter disc titles in this unit.
1 Display the function menu.
Refer to Introduction of advanced operations on
page 20.
2 Play the CD that you want to enter a
title for.
.u
co
m
4 Press DISP to select the desired character type.
Press DISP repeatedly to switch between the
following character types:
Alphabet (upper case), numbers and symbols
—Alphabet (lower case)—European letters,
such as those with accents (e.g. á, à, ä, ç)—
Numbers and symbols
a
3 Use MULTI-CONTROL to select
TitleInput "A" in the function menu.
0.
5 Push MULTI-CONTROL up or down to
select a letter of the alphabet.
13
6 Push MULTI-CONTROL left or right to
move the cursor to the previous or next
character position.
7 Move the cursor to the last position by
pushing MULTI-CONTROL right after entering the title.
When you push MULTI-CONTROL right one
more time, the entered title is stored in memory.
8 Press BAND to return to the playback
display.
Notes
! Titles remain in memory, even after the disc is
removed from the unit, and are recalled when
the disc is reinserted.
! After data for 48 discs are stored in the memory, data for a new disc overwrites the oldest
one.
22
En
Autogood products «130»
Section
Operating this unit
02
Playing songs on USB portable
audio player/USB memory
Basic Operations
.u
Selecting an audio file directly
in the current folder
The operation is the same as that of the builtin CD player.
Refer to Selecting a track directly on page 19.
co
1 WMA/MP3/AAC/WAV indicator
Shows the type of file currently playing.
2 Folder number indicator
3 Track number indicator
4 Play time indicator
5 Bit rate/sampling frequency indicator
m
a
Operating this unit
For details about the supported device, refer to
Portable audio player compatibility on page 6.
! When the USB portable audio player having
battery charging function is connected to this
unit and the ignition switch is set to ACC or
ON, the battery is charged.
! You can disconnect the USB portable audio
player/USB memory anytime you want to finish listening to it.
! If USB portable audio player/USB memory is
connected to this unit, the source is changed
to USB automatically. If you do not use an
USB device, disconnect it from this unit. Depending on the connected USB device, turning on the ignition switch while USB device is
connected to this unit may change the source
automatically.
13
0.
! When playing back VBR (variable bit
rate)-recorded WMA files, the average
bit rate value is displayed.
! When playing back VBR (variable bit
rate)-recorded MP3 files, VBR is displayed instead of bit rate value.
% Select a folder
Push MULTI-CONTROL up or down.
% Fast forward or reverse
Push and hold MULTI-CONTROL left or right.
% Select a track
Push MULTI-CONTROL left or right.
% Return to root folder
Press and hold BAND.
Displaying text information of
an audio file
The operation is the same as that of the builtin CD player.
Refer to Displaying text information on disc on
page 19.
Notes
! If the characters recorded on the audio file are
not compatible with the head unit, those characters are not displayed.
! The text information of some audio files may
not be correctly displayed.
Selecting files from the file
name list
Notes
! Optimum performance of this unit may not be
obtained depending on the connected USB
portable audio player/USB memory.
! If folder 01 (ROOT) contains no files, playback
commences with folder 02.
The operation is the same as that of the builtin CD player.
Refer to Selecting files from the file name list
on page 20.
En
Autogood products «130»
23
Section
Operating this unit
Introduction of advanced
operations
Notes
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
The function menu is displayed.
3 Turn MULTI-CONTROL to select the
function.
Play mode (repeat play)—Random mode
(random play)—Scan mode (scan play)—
Pause (pause)—Sound Retriever (sound retriever)
Function and operation
co
m
Play mode, Random mode, Scan mode,
Pause and Sound Retriever operations are
basically the same as that of the built-in CD
player.
! You can also select the function by pressing
FUNCTION on the remote control.
! To return to the ordinary display, press BAND.
! If you select another folder during repeat play,
the repeat play range changes to All repeat.
! If you perform track search or fast forward/reverse during Track repeat, the repeat play
range changes to Folder repeat.
! When Folder repeat is selected, it is not possible to play back a subfolder of that folder.
! After file or folder scanning is finished, normal playback of the files begins again.
a
1 Press MULTI-CONTROL to display the
main menu.
.u
02
Operation
Play mode
Refer to Selecting a repeat play
range on page 20.
However, the repeat play ranges
you can select are different from
that of the built-in CD player. The
repeat play ranges of the USB
portable audio player/USB memory are:
! Track repeat – Repeat just
the current file
! Folder repeat – Repeat the
current folder
! All repeat – Repeat all files
24
13
0.
Function name
Random mode
Refer to Playing tracks in random
order on page 21.
Scan mode
Refer to Scanning folders and
tracks on page 21.
Pause
Refer to Pausing playback on page
21.
Sound Retriever
Refer to Using Sound Retriever on
page 21.
En
Autogood products «130»
Section
Operating this unit
02
Browsing for a song
For details about the supported iPod, refer to
iPod® compatibility on page 6.
Searching songs by category
Operations to control an iPod with this unit is
designed to be as close to the iPod as possible
to make operation and song search easy.
! Depending on the number of files in the
iPod, there may be delay when displaying a
list.
! If the characters recorded on the iPod are
not compatible with this unit, those characters are not displayed.
Basic Operations
1
1 Song number indicator
2 Play time indicator
3 Song time (progress bar)
m
% Fast forward or reverse
Push and hold MULTI-CONTROL left or right.
0.
co
% Select a track (chapter)
Push MULTI-CONTROL left or right.
Notes
2 Use MULTI-CONTROL to select a category.
Turn to change the category; press to select.
Playlists (playlists)—Artists (artists)—
Albums (albums)—Songs (songs)—Podcasts
(podcasts)—Genres (genres)—Composers
(composers)—Audiobooks (audiobooks)
List for the selected category is displayed.
a
Press LIST.
.u
Operating this unit
Playing songs on iPod
13
! When using an iPod, iPod Dock Connector to
USB Cable is required.
! Read the precautions for iPod on page 67.
! While iPod is connected to this unit, PIONEER
(or (check mark)) is displayed on the iPod.
! If an error message is displayed, refer to Error
messages on page 63.
! When the ignition switch is set to ACC or ON,
the iPod’s battery is charged while the iPod is
connected to this unit.
! While the iPod is connected to this unit, the
iPod cannot be turned on or off.
! Before connecting the dock connector of this
unit to the iPod, disconnect the headphones
from the iPod.
! The iPod is turned off about two minutes after
the ignition switch is set to OFF.
# You can start playback throughout the selected category by pressing and holding
MULTI-CONTROL. You can also perform this operation by pushing and holding
MULTI-CONTROL right.
# You can also change the category by pushing
MULTI-CONTROL up or down.
# You can also select the category by pushing
MULTI-CONTROL right.
# To return to the previous category, push
MULTI-CONTROL left.
# To return to the top tier of categories, push
and hold MULTI-CONTROL left.
# To return to the ordinary display, press BAND.
# If you do not operate the list within about 30
seconds, the display automatically returns to the
ordinary display.
3 Repeat step 2 to find a song you want
to listen to.
Searching songs by alphabet
1
Press LIST.
En
Autogood products «130»
25
Section
Operating this unit
3 Press LIST to switch to alphabet search
mode.
4 Turn MULTI-CONTROL to select a desired alphabet.
5 Press MULTI-CONTROL to display the alphabetical list.
# If alphabet search is aborted, Not Found is
displayed.
Displaying text information on
iPod
3 Turn MULTI-CONTROL to select the
function.
Play mode (repeat play)—Shuffle mode
(shuffle)—Shuffle all (shuffle all)—
Link search (link search)—Control mode
(control mode)—Pause (pause)—
Audiobooks (audiobook speed)—
Sound Retriever (sound retriever)
Function and operation
Play mode, Pause and Sound Retriever operations are basically the same as that of the
built-in CD player.
Function name
Play mode
Pause
Refer to Pausing playback on page
21.
Sound Retriever
Refer to Using Sound Retriever on
page 21.
co
Notes
13
0.
# If the characters recorded on the iPod are not
compatible with this unit, those characters are
not displayed.
! You can scroll the text information to the left
by pressing and holding DISP.
! When Ever Scroll is set to ON at the initial setting, text information scrolls continuously in
the display. Refer to Switching the ever scroll
on page 38.
Introduction of advanced
operations
1 Press MULTI-CONTROL to display the
main menu.
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
26
Operation
Refer to Selecting a repeat play
range on page 20.
However, the repeat play ranges
you can select are different from
that of the built-in CD player. The
repeat play ranges of the iPod
are:
! Repeat One – Repeat the current song
! Repeat All – Repeat all songs
in the selected list
m
% Press DISP to select the desired text information.
Play time— : artist name and : song title
— : artist name and : album name— :
album name and : song title— : song title
and play time— : song title, : artist name
and : album name
The function menu is displayed.
a
2 Use MULTI-CONTROL to select a category.
Turn to change the category. Press to select.
.u
02
Notes
! You can also select the function by pressing
FUNCTION on the remote control.
! To return to the ordinary display, press BAND.
! If you do not operate functions within about
30 seconds, the display automatically returns
to the ordinary display.
! Control mode (control mode) function is
available only for iPod nano (second generation).
! When Control mode is on, only
Control mode and Sound Retriever can be
operated.
En
Autogood products «130»
Section
Operating this unit
02
Playing songs in a random
order (shuffle)
Notes
3 Press MULTI-CONTROL to select your favorite setting.
co
% Press
to turn shuffle all on.
All songs on the iPod play randomly.
This function is available only for iPod nano
(second generation).
This unit’s iPod function can be operated from
your iPod. Sound can be heard from car’s
speaker, and operation can be conducted from
your iPod.
! While this function is in use, even if the
ignition key is turned off, iPod is not turned
off. To turn off power, operate the iPod.
m
Playing all songs in a random
order (shuffle all)
Operating this unit’s iPod
function from your iPod
.u
! Shuffle Songs – Play back songs in the selected list in random order.
! Shuffle Albums – Play back songs from a
randomly selected album in order.
! Shuffle OFF – Cancel random play.
! If link search is aborted, Not Found is displayed.
! You can also turn this function on in the menu
that appears by using MULTI-CONTROL.
a
2 Use MULTI-CONTROL to select
Shuffle mode in the function menu.
Operating this unit
1 Display the function menu.
Refer to Introduction of advanced operations on
the previous page.
2 Use MULTI-CONTROL to select an album
or song from the list.
For more details about the selecting operation,
refer to step 2 of Browsing for a song on page
25.
Note
0.
# To turn shuffle all off, set Shuffle mode in the
FUNCTION menu to off.
13
You can also turn this function on in the menu
that appears by using MULTI-CONTROL.
Selecting songs from album list
of currently playing artist
Album list of the currently selected artist is
displayed. You can select an album or song
from the artist name.
! Depending on the number of files in the
iPod, there may be delay when displaying a
list.
1 Press and hold LIST to turn link search
on.
Searches albums of the artist and displays the
list.
1 Press iPod and hold to switch the control mode.
# Each pressing and holding iPod switches the
control mode.
# While using this function, play time and titles
are not displayed on this unit.
# Even if this function is performed, track up/
down can be operated from this unit.
# While using this function, browse function
cannot be operated from this unit.
2 Operate the connected iPod to select a
song and play.
Note
You can also turn this function on or off in the
menu that appears by using MULTI-CONTROL.
En
Autogood products «130»
27
Section
02
Operating this unit
Changing audiobook speed
While listening to an audiobook on iPod, playback speed can be changed.
1 Display the function menu.
Refer to Introduction of advanced operations on
page 26.
2 Use MULTI-CONTROL to select
Audiobooks in the function menu.
.u
13
0.
co
m
! Faster – Playback faster than normal speed
! Normal – Playback in normal speed
! Slower – Playback slower than normal
speed
a
3 Press MULTI-CONTROL to select your favorite setting.
Press MULTI-CONTROL repeatedly until the
desired setting appears in the display.
28
En
Autogood products «130»
Section
Audio Adjustments
03
Introduction of audio
adjustments
Using balance adjustment
You can change the fader/balance setting so
that it can provide the ideal listening environment in all occupied seats.
1
2
Use MULTI-CONTROL to select Fader.
# If the balance setting has been previously adjusted, Balance will be displayed.
1 Press MULTI-CONTROL to display the
main menu.
3 Push MULTI-CONTROL up or down to
adjust front/rear speaker balance.
Each time MULTI-CONTROL is pushed up or
down, the front/rear speaker balance moves
towards the front or rear.
F 15 to R 15 is displayed as the front/rear
speaker balance moves from front to rear.
.u
m
2 Use MULTI-CONTROL to select AUDIO.
Turn to change the menu option. Press to select.
The audio menu is displayed.
a
1 Audio display
Shows the audio adjustment status.
Audio Adjustments
1 Display the audio menu.
Refer to Introduction of audio adjustments on
this page.
# F/R 0 is the proper setting when only two
speakers are used.
# When the rear output setting is Rear SP :S/W,
you cannot adjust front/rear speaker balance.
Refer to Setting the rear output and subwoofer
controller on page 37.
13
0.
co
3 Turn MULTI-CONTROL to select the
audio function.
Turn MULTI-CONTROL to switch between the
audio functions in the following order.
Fader (balance adjustment)—Powerful (graphic equalizer adjustment)—50Hz (7-band
graphic equalizer adjustment)—LOUD (loudness)—Sub W.1 (subwoofer on/off setting)—
Sub W.2 (subwoofer setting)—Bass (bass
boost)—HPF (high pass filter)—SLA (source
level adjustment)—ASL (automatic sound levelizer)
# You can also select the audio function by
pressing AUDIO on the remote control.
# You can select the Sub W.2 only when subwoofer output is turned on in Sub W.1.
# When selecting FM as the source, you cannot
switch to SLA.
# To return to the display of each source, press
BAND.
# If you do not operate functions except for
50Hz within about 30 seconds, the display is
automatically returned to the ordinary display.
4 Push MULTI-CONTROL left or right to
adjust left/right speaker balance.
Each time MULTI-CONTROL is pushed left or
right, the left/right speaker balance moves towards the left or right.
L 15 to R 15 is displayed as the left/right
speaker balance moves from left to right.
Using the equalizer
The equalizer lets you adjust the equalization
to match the car’s interior acoustic characteristics as desired.
Recalling equalizer curves
There are seven stored equalizer curves which
you can easily recall at any time. Here is a list
of the equalizer curves.
En
Autogood products «130»
29
Section
Audio Adjustments
Equalizer curve
Powerful
Powerful
Natural
Natural
Vocal
Vocal
Custom1
Custom 1
Custom2
Custom 2
Flat
Flat
S.Bass
Super bass
1 Recall the equalizer curve you want to
adjust.
See Recalling equalizer curves on the previous
page.
# The actual range of the adjustments are different depending on which equalizer curve is selected.
# The equalizer curve with all frequencies set to
0 cannot be adjusted.
Adjusting 7-band graphic equalizer
m
! Custom1 and Custom2 are adjusted equalizer curves that you create. Adjustments
can be made with a 7-band graphic equalizer.
! When Flat is selected, no supplement or
correction is made to the sound. This is
useful to check the effect of the equalizer
curves by switching alternatively between
Flat and a set equalizer curve.
2 Push MULTI-CONTROL up or down to
adjust the equalizer curve.
Each time MULTI-CONTROL is pushed up or
down, the equalizer curve increases or decreases respectively.
+6 to –4 (or –6) is displayed as the equalizer
curve is increased or decreased.
a
Display
.u
03
co
1 Display the audio menu.
Refer to Introduction of audio adjustments on
the previous page.
For Custom1 and Custom2 equalizer curves,
you can adjust the level of each band.
! A separate Custom1 curve can be created
for each source. (The built-in CD player and
the multi-CD player are set to the same
equalizer adjustment setting automatically.) If you make adjustments when a
curve other than Custom2 is selected, the
equalizer curve settings will be memorized
in Custom1.
! A Custom2 curve can be created common
to all sources. If you make adjustments
when the Custom2 curve is selected, the
Custom2 curve will be updated.
13
0.
2 Use MULTI-CONTROL to select the graphic equalizer adjustment.
Powerful appears in the display.
If the equalizer curve has been previously selected, the curve of that previously selected
will be displayed instead of Powerful.
3 Push MULTI-CONTROL left or right to
select an equalizer curve.
Each time MULTI-CONTROL is pushed left or
right, equalizer curves are selected in the following order:
Powerful—Natural—Vocal—Custom1—
Custom2—Flat—S.Bass
Adjusting equalizer curves
The factory supplied equalizer curves, with the
exception of Flat, can be adjusted to a fine degree (nuance control).
30
1 Recall the equalizer curve you want to
adjust.
See Recalling equalizer curves on the previous
page.
2 Use MULTI-CONTROL to select 7-band
graphic equalizer adjustment.
Frequency and the level (e.g., 50Hz +4) appears in the display.
En
Autogood products «130»
Section
Audio Adjustments
03
3 Push MULTI-CONTROL left or right to
select the equalizer band to adjust.
Each time MULTI-CONTROL is pushed left or
right, equalizer bands are selected in the following order:
50Hz—125Hz—315Hz—800Hz—2kHz—
5kHz—12.5kHz
Using subwoofer output
4 Push MULTI-CONTROL up or down to
adjust the level of the equalizer band.
Each time MULTI-CONTROL is pushed up or
down, the level of the equalization band increases or decreases.
+6 to –6 is displayed as the level is increased
or decreased.
2
0.
Loudness compensates for deficiencies in the
low- and high-sound ranges at low volume.
13
1 Display the audio menu.
Refer to Introduction of audio adjustments on
page 29.
2
3 Press MULTI-CONTROL to turn subwoofer output on.
Normal appears in the display. Subwoofer output is now on.
a
# To turn subwoofer output off, press
MULTI-CONTROL again.
.u
4 Push MULTI-CONTROL left or right to
select the phase of subwoofer output.
Push MULTI-CONTROL left to select reverse
phase and Reverse appears in the display.
Push MULTI-CONTROL right to select normal
phase and Normal appears in the display.
co
Adjusting loudness
Use MULTI-CONTROL to select Sub W.1.
m
5 Press BAND to cancel the 7-band graphic equalizer adjustment.
1 Display the audio menu.
Refer to Introduction of audio adjustments on
page 29.
Audio Adjustments
# You can then select another band and adjust
the level.
This unit is equipped with a subwoofer output
which can be turned on or off.
Use MULTI-CONTROL to select LOUD.
3 Press MULTI-CONTROL to turn loudness
on.
Loudness level (e.g., Mid) appears in the display.
# To turn loudness off, press MULTI-CONTROL
again.
4 Push MULTI-CONTROL left or right to
select a desired level.
Each time MULTI-CONTROL is pushed left or
right, level is selected in the following order:
Low (low)—Mid (mid)—High (high)
Adjusting subwoofer settings
When the subwoofer output is on, you can adjust the cut-off frequency and the output level
of the subwoofer.
Only frequencies lower than those in the selected range are outputted from the subwoofer.
! When the subwoofer output is on, you can
select Sub W.2.
1 Display the audio menu.
Refer to Introduction of audio adjustments on
page 29.
2
Use MULTI-CONTROL to select Sub W.2.
3 Push MULTI-CONTROL left or right to
select cut-off frequency.
Each time MULTI-CONTROL is pushed left or
right, cut-off frequencies are selected in the
following order:
50Hz—63Hz—80Hz—100Hz—125Hz
En
Autogood products «130»
31
Section
Audio Adjustments
03
4 Push MULTI-CONTROL left or right to
select cut-off frequency.
Each time MULTI-CONTROL is pushed left or
right, cut-off frequencies are selected in the
following order:
50Hz—63Hz—80Hz—100Hz—125Hz
Boosting the bass
Adjusting source levels
Bass boost function boosts the bass level of
sound.
Source level adjustment (SLA) lets you adjust
the volume level of each source to prevent radical changes in volume when switching between sources.
! Settings are based on the FM volume level,
which remains unchanged.
2
Use MULTI-CONTROL to select Bass.
2 Display the audio menu.
Refer to Introduction of audio adjustments on
page 29.
co
m
3 Push MULTI-CONTROL up or down to
select a desired level.
0 to +6 is displayed as the level is increased or
decreased.
1 Compare the FM volume level with the
level of the source you wish to adjust.
.u
1 Display the audio menu.
Refer to Introduction of audio adjustments on
page 29.
a
4 Push MULTI-CONTROL up or down to
adjust the output level of the subwoofer.
Each time MULTI-CONTROL is pushed up or
down, subwoofer level increases or decreases.
+6 to -24 is displayed as the level is increased
or decreased.
3
0.
Using the high pass filter
13
When you do not want low sounds from the
subwoofer output frequency range to play
from the front or rear speakers, turn on the
HPF (high pass filter). Only frequencies higher
than those in the selected range are output
from the front or rear speakers.
1 Display the audio menu.
Refer to Introduction of audio adjustments on
page 29.
2
Use MULTI-CONTROL to select HPF.
3 Press MULTI-CONTROL to turn high
pass filter on.
80Hz appears in the display. High pass filter is
now on.
Use MULTI-CONTROL to select SLA.
4 Push MULTI-CONTROL up or down to
adjust the source volume.
Each time MULTI-CONTROL is pushed up or
down, source volume increases or decreases.
SLA +4 to SLA –4 is displayed as the source
volume is increased or decreased.
Notes
! The MW/LW volume level can also be adjusted
with source level adjustments.
! The built-in CD player and the multi-CD player
are set to the same source level adjustment
volume automatically.
! External unit 1 and external unit 2 are set to
the same source level adjustment volume
automatically.
# If the high pass filter has been previously adjusted, the frequency of that previously selected
will be displayed instead of 80Hz.
# To turn high pass filter off, press
MULTI-CONTROL again.
32
En
Autogood products «130»
Section
Audio Adjustments
03
Using automatic sound
levelizer
Audio Adjustments
During driving, noise in the car changes according to the driving speed and road conditions. The automatic sound levelizer (ASL)
monitors such varying noise and automatically increases the volume level, if this noise
becomes greater. The sensitivity (variation of
volume level to noise level) of ASL can be set
to one of five levels.
Use MULTI-CONTROL to select ASL.
# To turn ASL off, press MULTI-CONTROL
again.
m
3 Press MULTI-CONTROL to turn ASL on.
Mid appears in the display.
.u
2
a
1 Display the audio menu.
Refer to Introduction of audio adjustments on
page 29.
13
0.
co
4 Push MULTI-CONTROL left or right to
select the desired ASL level.
Each time MULTI-CONTROL is pushed left or
right, ASL level is selected in the following
order:
Low (low)—Mid-L (mid-low)—Mid (mid)—
Mid-H (mid-high)—High (high)
En
Autogood products «130»
33
Section
04
Initial Settings
# BT AUDIO and Pin code input can be selected only when Bluetooth adapter (e.g., CDBTB200) is connected to this unit.
# To cancel initial settings, press BAND.
Adjusting initial settings
Selecting the display language
Using the initial settings, you can customize
various system settings to achieve optimal performance from this unit.
1 Function display
! Shows the function status.
For your convenience, this unit equips multiple language display. You can select the language best suited to your first language.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
1
2 Use MULTI-CONTROL to select
Language select.
3 Press MULTI-CONTROL to select the language.
Each press of MULTI-CONTROL selects languages in the following order:
English—Français—Italiano—Español—
Deutsch—Nederlands—РУССКИЙ
co
m
2 Press MULTI-CONTROL and hold until
the initial setting menu appears in the display.
Display the intial setting menu.
.u
1 Press SRC and hold until the unit turns
off.
a
1
13
0.
3 Turn MULTI-CONTROL to select one of
the initial settings.
Turn MULTI-CONTROL to switch between the
functions in the following order.
Language select (language selection)—
Calendar (calendar)—Clock (clock)—
Off clock (off clock)—FM step (FM tuning
step)—Auto PI (auto PI seek)—Warning tone
(warning tone)—Face auto open (face auto
open)—AUX1 (auxiliary input 1)—AUX2 (auxiliary input 2)—Dimmer (dimmer)—
Brightness (brightness)—S/W control (rear
output and subwoofer controller)—Mute
(sound muting/attenuation)—Demonstration
(feature demo)—Reverse mode (reverse
mode)—Ever-scroll (ever scroll)—BT AUDIO
(Bluetooth audio)—Pin code input (pin code
input)—BT Version info. (Bluetooth version
information)
Use the following instructions to operate each
particular setting.
# You can also select the function by pressing
FUNCTION on the remote control.
34
Setting the date
The calender display adjusted in this mode appears when the telephone source is selected
or sources and the feature demo are off.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
1
Display the intial setting menu.
2 Use MULTI-CONTROL to select
Calendar.
Calendar appears in the display.
3 Push MULTI-CONTROL left or right to
select the segment of the calendar display
you wish to set.
Pushing MULTI-CONTROL left or right will select one segment of the calendar display:
Day—Month—Year
En
Autogood products «130»
Section
Initial Settings
04
Turning the off clock
display on or off
4 Push MULTI-CONTROL up or down to
set the date.
Pushing MULTI-CONTROL up will increase
the selected day, month or year. Pushing
MULTI-CONTROL down will decrease the selected day, month or year.
If the off clock display is turned on and the
sources and the feature demo are off, the
clock display appears on the display.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
1
Display the intial setting menu.
2
Use MULTI-CONTROL to select Clock.
3 Press MULTI-CONTROL to turn the off
clock display on.
# To turn the off clock display off, press
MULTI-CONTROL again.
m
1
2 Use MULTI-CONTROL to select
Off clock.
.u
Use these instructions to set the clock.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
Display the intial setting menu.
a
Setting the clock
Initial Settings
As you select segments of the calendar display the segment selected will blink.
Setting the FM tuning step
Normally the FM tuning step employed by
seek tuning is 50 kHz. When AF or TA is on,
the tuning step automatically changes to 100
kHz. It may be preferable to set the tuning step
to 50 kHz when AF is on.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
13
0.
co
3 Push MULTI-CONTROL left or right to
select the segment of the clock display you
wish to set.
Pushing MULTI-CONTROL left or right will select one segment of the clock display:
Hour—Minute
As you select segments of the clock display,
the selected segment blinks.
4 Push MULTI-CONTROL up or down to
put a clock right.
Note
You can match the clock to a time signal by
pressing MULTI-CONTROL.
! If 00 to 29, the minutes are rounded down.
(e.g., 10:18 becomes 10:00.)
! If 30 to 59, the minutes are rounded up. (e.g.,
10:36 becomes 11:00.)
1
Display the intial setting menu.
2
Use MULTI-CONTROL to select FM step.
3 Press MULTI-CONTROL to select the FM
tuning step.
Pressing MULTI-CONTROL repeatedly will
switch the FM tuning step between 50 kHz
and 100 kHz while AF or TA is on. The selected
FM tuning step will appear in the display.
Note
The tuning step remains at 50 kHz during manual
tuning.
En
Autogood products «130»
35
Section
Initial Settings
04
Switching Auto PI Seek
1
The unit can automatically search for a different station with the same programming, even
during preset recall.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
2 Use MULTI-CONTROL to select
Face auto open.
1
Display the intial setting menu.
2
Use MULTI-CONTROL to select Auto PI.
3 Press MULTI-CONTROL to turn Auto PI
seek on.
3 Press MULTI-CONTROL to turn the face
auto open on.
# To turn the face auto open off, press
MULTI-CONTROL again.
Switching the auxiliary setting
Auxiliary devices connected to this unit can be
activated individually. Set each AUX source to
ON when using. For more information about
connecting or using auxiliary devices, refer to
Using the AUX source on page 40.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
m
Switching the warning tone
.u
a
# To turn Auto PI seek off, press
MULTI-CONTROL again.
Display the intial setting menu.
1
Display the intial setting menu.
Display the intial setting menu.
13
1
0.
co
If the front panel is not detached from the
head unit within four seconds of turning off
the ignition, a warning tone sounds. You can
turn off the warning tone.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
2 Use MULTI-CONTROL to select
Warning tone.
3 Press MULTI-CONTROL to turn warning
tone on.
# To turn warning tone off, press
MULTI-CONTROL again.
Switching the face auto open
To protect against theft, this unit features detachable front panel. To detach the front panel
easily, the front panel opens automatically.
This function is on as a default.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
36
2 Use MULTI-CONTROL to select AUX1/
AUX2.
3 Press MULTI-CONTROL to turn AUX1/
AUX2 on.
# To turn AUX off, press MULTI-CONTROL
again.
Switching the dimmer setting
To prevent the display from being too bright at
night, the display is automatically dimmed
when the car’s headlights are turned on. You
can turn the dimmer on or off.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
1
Display the intial setting menu.
2
Use MULTI-CONTROL to select Dimmer.
En
Autogood products «130»
Section
Initial Settings
04
3 Press MULTI-CONTROL to turn dimmer
on.
# To turn dimmer off, press MULTI-CONTROL
again.
You can adjust the display brightness.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
# When no subwoofer is connected to the rear
output, select Rear SP :F.Range.
# When a subwoofer is connected to the rear
output, set for subwoofer Rear SP :S/W.
Notes
# When dimmer is functioning, the brightness
level can be adjusted 0 to 10.
! Even if you change this setting, there is no
output unless you turn the subwoofer output
on (refer to Using subwoofer output on page
31).
! If you change this setting, subwoofer output
in the audio menu return to the factory settings.
! Both rear speaker lead outputs and RCA rear
output are switched simultaneously in this
setting.
Setting the rear output and
subwoofer controller
Switching the sound
muting/attenuation
This unit’s rear output (rear speaker leads output and RCA rear output) can be used for fullrange speaker (Rear SP :F.Range) or subwoofer (Rear SP :S/W) connection. If you switch
the rear output setting to Rear SP :S/W, you
can connect a rear speaker lead directly to a
subwoofer without using an auxiliary amp.
Initially, the unit is set for rear full-range speaker connection (Rear SP :F.Range).
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
Sound from this system is muted or attenuated automatically when the signal from the
equipment with mute function is received.
! The sound is muted or attenuated, MUTE
or ATT are displayed and no audio adjustment is possible.
! Sound from this system returns to normal
when the muting or attenuation is canceled.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
1
1
Display the intial setting menu.
2
Use MULTI-CONTROL to select Mute.
Display the intial setting menu.
a
2 Use MULTI-CONTROL to select
Brightness.
13
0.
co
m
3 Push MULTI-CONTROL left or right to
adjust the brightness level.
0 to 15 is displayed as the level is increased or
decreased.
.u
1
Initial Settings
Adjusting the brightness
3 Press MULTI-CONTROL to switch the
rear output setting.
Pressing MULTI-CONTROL will switch between Rear SP :F.Range (full-range speaker)
and Rear SP :S/W (subwoofer) and that status
will be displayed.
Display the intial setting menu.
2 Use MULTI-CONTROL to select
S/W control.
En
Autogood products «130»
37
Section
Initial Settings
04
3 Press MULTI-CONTROL to switch the telephone muting/attenuation.
Pressing MULTI-CONTROL will switch between TEL ATT (attenuation) and TEL mute
(muting) and that status will be displayed.
2 Use MULTI-CONTROL to select
Reverse mode.
3 Press MULTI-CONTROL to turn the reverse mode on.
# To turn the reverse mode off, press
MULTI-CONTROL again.
Switching the feature demo
Display the intial setting menu.
When ever scroll is set to on, CD text information scrolls continuously in the display. Set to
off if you prefer the information to scroll just
once.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
m
2 Use MULTI-CONTROL to select
Demonstration.
3 Press MULTI-CONTROL to turn the feature demo on.
co
# To turn the feature demo off, press
MULTI-CONTROL again.
1
0.
Notes
Switching the ever scroll
.u
1
Note
You can also turn on or off reverse mode by pressing BAND while this unit is turned off. For more
details, see Reverse mode on page 8.
a
The feature demo automatically starts when
power to this unit is turned off while the ignition switch is set to ACC or ON.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
13
! Remember that if the feature demo continues
operating when the car engine is turned off, it
may drain battery power.
! You can also turn on or off feature demo by
pressing DISP while this unit is turned off. For
more details, see About the demo mode on
page 7.
Display the intial setting menu.
2 Use MULTI-CONTROL to select
Ever-scroll.
3 Press MULTI-CONTROL to turn the ever
scroll on.
# To turn the Ever Scroll off, press
MULTI-CONTROL again.
Activating the BT Audio source
Switching the reverse mode
If you do not perform an operation for about
30 seconds, screen indications start to reverse,
and continue reversing every 10 seconds.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
1
38
Display the intial setting menu.
You need to activate the BT Audio source in
order to use a Bluetooth audio player.
! You can only operate this function when
Bluetooth adapter (e.g. CD-BTB200) is connected to this unit.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
1
Display the intial setting menu.
En
Autogood products «130»
Section
Initial Settings
04
# Pushing MULTI-CONTROL right in the confirmation display returns you to the PIN code input
display, and you can change the PIN code.
2 Use MULTI-CONTROL to select
BT AUDIO.
3 Press MULTI-CONTROL to turn the
BT Audio source on.
# To turn the BT Audio source off, press
MULTI-CONTROL again.
a
1
Display the intial setting menu.
2 Use MULTI-CONTROL to select
BT Version info.
The system (microprocessor) version of this
unit is displayed.
Display the intial setting menu.
3 Push MULTI-CONTROL left to switch to
the version of the Bluetooth module of this
unit.
# Pushing MULTI-CONTROL right returns to the
system version of this unit.
13
1
0.
co
m
To connect your cellular phone to this unit via
Bluetooth wireless technology, you need to
enter PIN code on your phone to verify the
connection. The default code is 0000, but you
can change this in this function.
! With some Bluetooth audio players, you
may be required to enter the Bluetooth
audio player PIN code in advance to set
this unit for a connection.
! You can only operate this function when
Bluetooth adapter (e.g. CD-BTB200) is connected to this unit.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
Should this unit fails to operate properly and
you consult your dealer for repair, you may be
asked to indicate the system versions of this
unit and of Bluetooth module. You can display
the versions and confirm them.
! For this function, verify the topic Adjusting
initial settings before initiating the operation.
.u
Entering PIN code for
Bluetooth wireless connection
Initial Settings
Displaying system version
for repair
2 Use MULTI-CONTROL to select
Pin code input.
3 Push MULTI-CONTROL up or down to
select a number.
4 Push MULTI-CONTROL left or right to
move the cursor to the previous or next position.
5 After inputting PIN code (up to 16 digits), press MULTI-CONTROL.
PIN code can be stored in memory.
When you press MULTI-CONTROL again on
the same display, the PIN code you entered is
stored in this unit.
En
Autogood products «130»
39
Section
Other Functions
Using the AUX source
Selecting AUX as the source
Up to two auxiliary devices such as VCR or
portable devices (sold separately) can be connected to this unit. When connected, auxiliary
devices are automatically read as AUX sources
and assigned to AUX1 or AUX2. The relationship between AUX1 and AUX2 sources is explained below.
% Press SRC to select AUX as the source.
# If the auxiliary setting is not turned on, AUX
cannot be selected. For more details, see Switching the auxiliary setting on page 36.
Setting the AUX title
The title displayed for the AUX1 or AUX2
source can be changed.
About AUX1 and AUX2
1 After you have selected AUX as the
source, use MULTI-CONTROL and select
FUNCTION to display TitleInput "A".
AUX1 source:
2 Enter a title in the same way as the
built-in CD player.
For details concerning operation, refer to Entering disc titles on page 22.
When connecting auxiliary equipment using a
stereo mini plug cable
m
% Insert the stereo mini plug into the
input jack on this unit.
For more details, refer to the installation manual.
This auxiliary device is automatically set to
AUX1.
a
There are two methods to connect auxiliary devices to this unit.
.u
05
AUX2 source:
0.
co
Using the external unit
13
When connecting auxiliary equipment using an
IP-BUS-RCA Interconnector (sold separately)
% Use an IP-BUS-RCA Interconnector such
as the CD-RB20/CD-RB10 (sold separetely)
to connect this unit to auxiliary equipment
featuring RCA output.
For more details, refer to the IP-BUS-RCA Interconnector owner’s manual.
This auxiliary device is automatically set to
AUX2.
# You can only make this type of connection if
the auxiliary device has RCA outputs.
40
External unit refers to a Pioneer product (such
as ones available in the future) that, although
incompatible as a source, enables control of
basic functions with this unit. Two external
units can be controlled with this unit. When
two external units are connected, the external
unit is automatically allocated to external unit
1 or external unit 2 by this unit.
Basic operations of the external unit are explained below. Allocated functions are different depending on the connected external unit.
For details concerning functions, refer to external unit’s owner’s manual.
Selecting the external unit as
the source
% Press SRC to select EXTERNAL as the
source.
En
Autogood products «130»
Section
Other Functions
05
Basic operation
Using different
entertainment displays
Functions allocated to the following operations are different depending on the connected external unit. For details concerning
functions, refer to the connected external
unit’s owner’s manual.
You can enjoy entertainment displays while listening to each sound source.
1 Press MULTI-CONTROL to display the
main menu.
% Press BAND.
% Push MULTI-CONTROL left or right.
% Push and hold MULTI-CONTROL left or
right.
.u
m
Using the functions allocated
to 1 to 6 keys
co
% Press any of 1 to 6 on the remote control.
Advanced operations
3 Use MULTI-CONTROL to change the display.
Turn to change the menu option. Press to select.
BGV-1 (background visual 1)—BGV-2 (background visual 2)—BGP-1 (background picture
1)—BGP-2 (background picture 2)—BGP-3
(background picture 3)—BGP-4 (background
picture 4)—SIMPLE-1 (simple display 1)—
SIMPLE-2 (simple display 2)—LEVEL METER
(level meter)—VISUALIZER1 (visualizer 1)—
VISUALIZER2 (visualizer 2)—VISUALIZER3 (visualizer 3)—SPECTRUM ANALYZER 1 (spectrum analyzer 1)—SPECTRUM ANALYZER 2
(spectrum analyzer 2)—MOVIE (movie)—
ENT CLOCK (entertainment clock)
a
% Push MULTI-CONTROL up or down.
2 Use MULTI-CONTROL to select
ENTERTAINMENT.
Turn to change the menu option. Press to select.
Other Functions
% Press and hold BAND.
0.
1 Press MULTI-CONTROL to display the
main menu.
13
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
3 Turn MULTI-CONTROL to select the
function.
Function1 (function 1)—Function2 (function
2)—Function3 (function 3)—Function4 (function 4)—Auto/Manual (auto/manual)
! You can also turn Function1 on or off by
pressing PGM on the remote control.
Notes
! You can also select the function by pressing
FUNCTION on the remote control.
! To return to the ordinary display, press
BAND.
# You can also switch between the display by
pressing ENT on the remote control.
# To return to the playback display, press
BAND.
Using the PGM button
You can operate the preprogrammed functions
for each source by using PGM on the remote
control.
% Press PGM to turn pause on when selecting the following sources:
! COMPACT DISC – Built-in CD player
! MULTI CD – Multi-CD player
! USB – USB portable audio player/USB
memory
En
Autogood products «130»
41
Section
05
Other Functions
! IPOD – iPod
! BT Audio – Bluetooth audio player
! DVD – DVD player/multi-DVD player
# To turn pause off, press PGM again.
% Press PGM and hold to turn BSM on
when selecting tuner as the source.
Press PGM and hold until the BSM turns on.
# To cancel the storage process, press PGM
again.
% Press PGM and hold to turn BSSM on
when selecting television as the source.
Press PGM and hold until the BSSM turns on.
13
0.
co
m
.u
a
# To cancel the storage process, press PGM
again.
42
En
Autogood products «130»
Section
Available accessories
06
Displaying text information on
iPod
Playing songs on iPod
Basic operation
% Press DISP to select the desired text information.
Play time— : artist name and : song title
— : artist name and : album name— :
album name and : song title— : song title
and play time
You can use this unit to control an interface
adapter for iPod, which is sold separately.
Notes
a
1 Song number indicator
2 Play time indicator
3 Song time (progress bar)
m
% Fast forward or reverse
Push and hold MULTI-CONTROL left or right.
% Select a track
Push MULTI-CONTROL left or right.
Browsing for a song
co
Notes
! You can scroll the text information to the left
by pressing and holding DISP.
! When Ever Scroll is set to ON at the initial setting, text information scrolls continuously in
the display. Refer to Switching the ever scroll
on page 38.
.u
Available accessories
# If the characters recorded on the iPod are not
compatible with this unit, those characters are
not displayed.
13
0.
! Read the precautions for iPod on page 67.
! While iPod is connected to this unit, PIONEER
(or (check mark)) is displayed on the iPod.
! If an error message is displayed, refer to Error
messages on page 63.
! When the ignition switch is set to ACC or ON,
the iPod’s battery is charged while the iPod is
connected to this unit.
! While the iPod is connected to this unit, the
iPod cannot be turned on or off.
! Before connecting the dock connector of this
unit to the iPod, disconnect the headphones
from the iPod.
! The iPod is turned off about two minutes after
the ignition switch is set to OFF.
The operation is the same as that of the iPod
connected to USB interface of this unit. (Refer
to Browsing for a song on page 25.)
However, the selectable categories are slightly
different. Selectable categories are
Playlists (playlists)—Artists (artists)—
Albums (albums)—Songs (songs)—Genres
(genres)
Introduction of advanced
operations
1 Press MULTI-CONTROL to display the
main menu.
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
The function menu is displayed.
En
Autogood products «130»
43
Section
06
Available accessories
Bluetooth Audio
3 Turn MULTI-CONTROL to select the
function.
Play mode (repeat play)—Shuffle mode
(shuffle)—Pause (pause)
Basic Operations
If you connect a Bluetooth adapter (e.g. CDBTB200) to this unit, you can control Bluetooth
audio players via Bluetooth wireless technology.
Function and operation
Play mode and Pause operations are basically
the same as that of the built-in CD player.
Notes
Important
! Depending on the Bluetooth audio player connected to this unit, the operations available
with this unit are limited to the following two
levels:
— Lower level: Only playing back songs on
your audio player is possible.
— Higher level: Playing back, pausing, selecting songs, etc., are possible (all the operations illustrated in this manual).
! Since there are a number of Bluetooth audio
players available on the market, operations
with your Bluetooth audio player using this
unit vary in great range. Refer to the instruction manual that came with your Bluetooth
audio player as well as this manual while operating your player on this unit.
! Information about songs (e.g. the elapsed
playing time, song title, song index, etc.) cannot be displayed on this unit.
! While you are listening to songs on your Bluetooth audio player, refrain from operating on
your cellular phone as much as possible. If
you try operating your cellular phone, the signal from your cellular phone may cause noise
on the song playback.
Refer to Pausing playback on page
21.
co
Pause
1 Device name
Shows the device name of the connected
Bluetooth audio player (or Bluetooth adapter).
a
Play mode
.u
Operation
Refer to Selecting a repeat play
range on page 20.
However, the repeat play ranges
you can select are different from
that of the built-in CD player. The
repeat play ranges of the iPod are:
! Repeat One – Repeat the current song
! Repeat All – Repeat all songs
in the selected list
m
Function name
13
0.
! You can also select the function by pressing
FUNCTION on the remote control.
! To return to the ordinary display, press BAND.
! If you do not operate functions within about
30 seconds, the display automatically returns
to the ordinary display.
Playing songs in a random
order (shuffle)
% Press
repeatedly to select the desired setting.
! Shuffle Songs – Play back songs in the selected list in random order.
! Shuffle Albums – Play back songs from a
randomly selected album in order.
! Shuffle OFF – Cancel random play.
Note
You can also turn this function on in the menu
that appears by using MULTI-CONTROL.
44
En
Autogood products «130»
Section
Available accessories
06
Notes
! You can also select the function by pressing
FUNCTION on the remote control.
! To return to the ordinary display, press BAND.
! If a Bluetooth audio player is not connected to
this unit yet, Connection open and
Device info appear in the function menu and
other functions are not available.
! If a Bluetooth audio player is connected via
higher level, Connection open does not appear in the function menu and the other functions are available.
! If a Bluetooth audio player is connected via
lower level, only Disconnect audio and
Device info appear in the function menu.
! If you do not operate functions other than
Connection open and Disconnect audio
within about 30 seconds, the display is automatically returned to the ordinary display.
13
0.
co
m
! For details concerning operation, refer to the
Bluetooth adapter’s operation manual. This
section provides brief information on Bluetooth audio player operations with this unit,
which slightly differs or is abbreviated from
that described in the Bluetooth adapter’s operation manual.
! Even though your audio player does not contain a Bluetooth module, you can still control
it from this unit via Bluetooth wireless technology. To control your audio player using this
unit, connect a product featuring Bluetooth
wireless technology (available on the market)
to your audio player and connect the Bluetooth adapter (e.g. CD-BTB200) to this unit.
Notes
Available accessories
% Select a track
Push MULTI-CONTROL left or right.
# Pause is the same as that of the built-in CD
player. (Refer to Pausing playback on page 21.)
a
% Fast forward or reverse
Push and hold MULTI-CONTROL left or right.
(Play)—Stop (Stop)—Pause (pause)—
Device info (device information)
.u
! When you are talking on a cellular phone connected to this unit via Bluetooth wireless technology, song playback from your Bluetooth
audio player connected to this unit is muted.
! Even if while you are listening to a song on
your Bluetooth audio player and you switch to
another source, playback of song continues.
Function and operation
1 Press MULTI-CONTROL to display the
main menu.
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
The function menu is displayed.
3 Turn MULTI-CONTROL to select the
function.
Connection open (connection open)—
Disconnect audio (disconnect audio)—Play
Connecting a Bluetooth audio
player
1 Display the function menu.
Refer to Function and operation on this page.
2 Use MULTI-CONTROL to select
Connection open in the function menu.
3 Press MULTI-CONTROL to open the connection.
Always waiting is displayed. This unit is now
on standby for connection from Bluetooth
audio player.
If your Bluetooth audio player is set ready for
Bluetooth wireless connection, connection to
this unit is automatically established.
En
Autogood products «130»
45
Section
Available accessories
Before you can use audio players you may need
to enter the PIN code into this unit. If your player
requires a PIN code to establish a connection,
look for the code on the player or in its accompanying documentation. Refer to Entering PIN code
for Bluetooth wireless connection on page 39.
Playing songs on Bluetooth
audio player
1 Display the function menu.
Refer to Function and operation on the previous
page.
2 Use MULTI-CONTROL to select Play in
the function menu.
1 Display the function menu.
Refer to Function and operation on the previous
page.
2 Use MULTI-CONTROL to select
Device info in the function menu.
3 Push MULTI-CONTROL left to switch to
the BD address.
12-digit hexadecimal string is displayed.
# Pushing MULTI-CONTROL right returns to the
device name.
co
Stopping playback
Displaying BD (Bluetooth
Device) address
m
3 Press MULTI-CONTROL to start playback.
3 Press MULTI-CONTROL to disconnect
the Bluetooth audio player.
Disconnected is displayed. The Bluetooth
audio player is now diconnected from this
unit.
a
Note
.u
06
0.
1 Display the function menu.
Refer to Function and operation on the previous
page.
13
2 Use MULTI-CONTROL to select Stop in
the function menu.
3 Press MULTI-CONTROL to stop the playback.
Bluetooth Telephone
Basic Operations
If you use a Bluetooth adapter (e.g. CDBTB200), you can connect a cellular phone featuring Bluetooth wireless technology to this
unit for hands-free, wireless calls, even while
driving.
Disconnecting a Bluetooth
audio player
1 Display the function menu.
Refer to Function and operation on the previous
page.
2 Use MULTI-CONTROL to select
Disconnect audio in the function menu.
1 Device name
Shows the device name of the cellular phone.
2 Signal level indicator
Shows the signal strength of cellular phone.
! Signal level indicator may differ from
the actual signal level.
46
En
Autogood products «130»
Section
Available accessories
06
! Incoming call notice is not displayed for
calls made when your cellular phone is
disconnected from this unit.
1 Connection
For detailed instructions on connecting your
phone to this unit via Bluetooth wireless technology, refer to Connecting a cellular phone on
page 49.
# Your phone should now be temporarily connected. However, to make best use of the technology, we recommend you register the phone to
this unit.
Important
13
0.
co
m
6 Automatic answering/Automatic rejecting indicator
Shows AUTO when the automatic answering
function is on (for more details, refer to Setting
automatic answering on page 55).
Shows REJECT when the automatic rejecting
function is on (for more details, refer to Setting
automatic rejecting on page 54).
7 Clock display
Shows the time (if connected with a phone).
8 Calendar display
Shows the day, month and year (if connected
with a phone).
Before you can use the hands-free phoning
function you must set up the unit for use with
your cellular phone. This entails establishing a
Bluetooth wireless connection between this
unit and your phone, registering your phone
with this unit, and adjusting the volume level.
Available accessories
5 Incoming call notice indication
Shows when an incoming call has been received and not checked yet.
Setting up for hands-free phoning
a
! Battery strength indicator may differ
from the actual battery strength.
! If the battery strength is not available,
nothing is displayed in the battery
strength indicator area.
! When selecting the phone source, you can
only operate Fader (balance adjustment) in
the audio menu.
.u
3 User number indicator
Shows the registration number of the cellular
phone.
4 Battery strength indicator
Shows the battery strength of cellular phone.
! Since this unit is on standby to connect with
your cellular phone via Bluetooth wireless
technology, using this unit without running
the engine can result in battery drainage.
! Advanced operations that require your attention such as dialing numbers on the monitor,
using phone book, etc., are prohibited while
you are driving. When you need to use these
advanced operations, stop your vehicle in a
safe place.
Notes
2 Registration
To register your temporarily connected phone,
refer to Registering a connected cellular phone
on page 50.
3 Volume adjustment
Adjust the earpiece volume on your cellular
phone for comfort. When adjusted, the volume
level is memorized in this unit as the default
setting.
# Caller’s voice volume and ring volume may
vary depending on the type of cellular phone.
# If the difference between the ring volume and
caller’s voice volume is big, overall volume level
may become unstable.
# Before disconnecting the cellular phone from
this unit, make sure to adjust the volume to a
proper level. If the volume is muted (zero level) on
your cellular phone, the volume level of your cellular phone remains muted even after the cellular
phone is disconnected.
! Equalizer curve for the phone source is fixed.
En
Autogood products «130»
47
Section
Available accessories
% End all calls
Push MULTI-CONTROL down.
Making a phone call
Voice recognition
1 Press BAND and hold until Voice dial
appears in the display.
Voice dial appears in the display. When
Voice dial ON is displayed, voice recognition
function is now ready.
# If your cellular phone does not feature voice
recognition function, No voice dial appears in
the display and opearation is not available.
2
Pronounce the name of your contact.
Taking a phone call
% Switch between callers on hold
Press MULTI-CONTROL.
# You can also perform this operation by pushing MULTI-CONTROL up.
% Rejecting a call waiting
Push MULTI-CONTROL down.
Notes
! Pushing MULTI-CONTROL down ends all
calls including calls waiting on line.
! To end the call, both you and your caller need
to hang up the phone.
a
06
.u
Answering or rejecting an incoming call
% Answering an incoming call
When a call comes in, press
MULTI-CONTROL.
Function and operation
m
0.
% End a call
Push MULTI-CONTROL down.
13
% Rejecting an incoming call
When a call comes in, push MULTI-CONTROL
down.
Notes
! If private mode is selected on the cellular
phone, hands-free phoning may not be performed.
! The estimated call time appears in the display
(this may differ slightly from the actual call
time).
Operating a call waiting
% Answering a call waiting
When a call comes in, press
MULTI-CONTROL.
# You can also perform this operation by pushing MULTI-CONTROL up.
48
1 Press MULTI-CONTROL to display the
main menu.
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
The function menu is displayed.
co
# You can also perform this operation by pushing MULTI-CONTROL up.
3 Turn MULTI-CONTROL to select the
function.
Search & Connect (search and connect)—
Connection open (connection open)—
Disconect phone (disconnect phone)—
Connect phone (connect phone)—Set phone
(registering phone)—Delete phone (delete
phone)—PH.B.Transfer (phone book transfer)
—PH.B.Name view (phone book name view)
—Clear memory (clear memory)—
Number dial (call by entering number)—
Refuse calls (automatic reject setting)—
Auto answer (automatic answer setting)—
Ring tone (ring tone select)—Auto connect
(automatic connection setting)—Echo cancel
(echo cancel)—Device info (device information)
If not connected yet
The following functions cannot be operated.
En
Autogood products «130»
Section
Available accessories
If connected but not registered yet
The following functions cannot be operated.
Search & Connect (search and connect)
Connection open (connection open)
Connect phone (connect phone)
PH.B.Name view (phone book name view)
Clear memory (clear memory)
If already connected and registered
The following functions cannot be operated.
!
!
!
!
Search & Connect (search and connect)
Connection open (connection open)
Connect phone (connect phone)
Set phone (registering phone)
1 Display the function menu.
Refer to Function and operation on the previous
page.
2 Use MULTI-CONTROL to select
Search & Connect in the function menu.
3 Press MULTI-CONTROL to search for
available cellular phones.
While searching, SEARCHING flashes. When
available cellular phones featuring Bluetooth
wireless technology are found, device name or
Name not found (if names cannot be obtained) is displayed.
# If this unit fails to find any available cellular
phones, Not found is displayed.
4 Push MULTI-CONTROL up or down to
select a device name you want to connect.
m
Notes
Searching for available cellular phones
5 Press MULTI-CONTROL to connect the
selected cellular phone.
While connecting, Connecting flashes. To
complete the connection, check the device
name (Pioneer BT Unit) and enter the link
code on your cellular phone. If the connection
is established, Connected is displayed.
13
0.
co
! You can also select the function by pressing
FUNCTION on the remote control.
! To return to the playback display, press BAND.
! Device info is the same as that of the Bluetooth audio. (Refer to Displaying BD (Bluetooth
Device) address on page 46.)
! PH.B.Name view (phone book name view)
cannot be selected for cellular phone registered guest phone.
! If cellular phone is connected to this unit via
Bluetooth wireless technology with HSP
(Head Set Profile), PH.B.Name view,
Clear memory, Number dial and
Refuse calls cannot be selected.
! If you do not operate functions other than
Search & Connect, Connection open,
Connect phone, PH.B.Transfer,
Disconect phone, Number dial,
Clear memory and PH.B.Name view within
about 30 seconds, the display automatically
returns to the ordinary display.
Available accessories
!
!
!
!
!
Connecting a cellular phone
a
Disconect phone (disconnect phone)
Set phone (registering phone)
Clear memory (clear memory)
PH.B.Name view (phone book name view)
Number dial (call by entering number)
.u
!
!
!
!
!
06
# The link code is set to 0000 as default. You
can change this code in the initial setting. Refer
to Entering PIN code for Bluetooth wireless connection on page 39.
Using a cellular phone to initiate a
connection
1 Display the function menu.
Refer to Function and operation on the previous
page.
2 Use MULTI-CONTROL to select
Connection open in the function menu.
En
Autogood products «130»
49
Section
Available accessories
4 Use cellular phone to connect to this
unit.
# The link code is set to 0000 as default. You
can change this code in the initial setting. Refer
to Entering PIN code for Bluetooth wireless connection on page 39.
Disconnecting a cellular phone
1 Display the function menu.
Refer to Function and operation on page 48.
4 Press MULTI-CONTROL to register the
currently connected phone.
When registration is completed,
Reg.Completed is displayed.
# If the registration fails, Reg.ERROR is displayed. In this case, return to step 1 and try
again.
Deleting a registered phone
1 Display the function menu.
Refer to Function and operation on page 48.
2 Use MULTI-CONTROL to select
Delete phone in the function menu.
3 Push MULTI-CONTROL up or down to
select a registration assignment.
P1 (user phone 1)—P2 (user phone 2)—P3
(user phone 3)—G1 (guest phone 1)—G2
(guest phone 2)
co
m
2 Use MULTI-CONTROL to select
Disconect phone in the function menu.
Device name of the connected phone appears
in the display.
more detailed instructions, see Deleting a registered phone on this page.
a
3 Press MULTI-CONTROL to open the connection.
Always waiting flashes and the unit is now
on standby for connection from a cellular
phone.
.u
06
0.
3 Press MULTI-CONTROL to disconnect a
cellular phone from this unit.
After disconnection is completed,
Disconnected is displayed.
13
Registering a connected
cellular phone
1 Display the function menu.
Refer to Function and operation on page 48.
2 Use MULTI-CONTROL to select
Set phone in the function menu.
# If the assignment is empty, No data is displayed and operation is not possible.
4 Push MULTI-CONTROL right to select
Delete YES.
Delete YES is displayed. Deleting phone is
now on standby.
5 Press MULTI-CONTROL to delete the
phone.
After the phone is deleted, Deleted is displayed.
3 Push MULTI-CONTROL up or down to
select a registration assignment.
P1 (user phone 1)—P2 (user phone 2)—P3
(user phone 3)—G1 (guest phone 1)—G2
(guest phone 2)
# As you select each assignment, you can see
whether or not a phone is already registered. If
the assignment is empty, No data is displayed. If
the assignment is already taken, the device name
appears. To replace an assignment with a new
phone, first delete the current assignment. For
50
En
Autogood products «130»
Section
Available accessories
06
Connecting to a registered
cellular phone
2 Use MULTI-CONTROL to select
PH.B.Transfer in the function menu.
Connecting to a registered phone
manually
3 Press MULTI-CONTROL to enter in the
phone book transfer standby mode.
Transfer YES appears in the display.
1 Display the function menu.
Refer to Function and operation on page 48.
4 Press MULTI-CONTROL to show the confirmation display.
Transfer YES appears in the display.
2 Use MULTI-CONTROL to select
Connect phone in the function menu.
# The display indicates how many entries have
been transferred and the total number to be
transferred.
6 Data transferred is displayed and
phone book transfer is completed.
m
4 Press MULTI-CONTROL to connect the
selected cellular phone.
While connecting, Connecting is displayed.
After the connection is completed, Connected
is displayed.
.u
a
# If the assignment is empty, No data is displayed and operation is not possible.
5 Use cellular phone to perform phone
book transfer.
Perform phone book transfer using the cellular phone. For detailed instructions, refer to
the instruction manual that came with your
cellular phone.
Available accessories
3 Push MULTI-CONTROL up or down to
select a registration assignment.
P1 (user phone 1)—P2 (user phone 2)—P3
(user phone 3)—G1 (guest phone 1)—G2
(guest phone 2)
co
Changing the phone book display order
Connecting to a registered phone
automatically
0.
1 Display the function menu.
Refer to Function and operation on page 48.
13
2 Use MULTI-CONTROL to select
Auto connect in the function menu.
1 Display the function menu.
Refer to Function and operation on page 48.
2 Use MULTI-CONTROL to select
PH.B.Name view in the function menu.
Invert names YES appears in the display.
3 Press MULTI-CONTROL to turn automatic connection on.
If your cellular phone is ready for Bluetooth
wireless connection, connection to this unit is
automatically established.
3 Press MULTI-CONTROL to change the
name view order.
Inverted is displayed and the name view
order is changed.
Pressing MULTI-CONTROL repeatedly
changes the name view order between first
name and last name.
# To turn automatic connection off, press
MULTI-CONTROL again.
Calling a number in the phone book
Important
Using the phone book
Transferring entries to the phone book
Be sure to park your vehicle and apply the parking brake when performing this operation.
The Phone Book can hold a total of 500 entries. 300 from User 1, 150 from User 2, and 50
from User 3.
After finding the number you want to call in
the phone book, you can select the entry and
make the call.
1 Display the function menu.
Refer to Function and operation on page 48.
1
Press LIST to display the phone book.
En
Autogood products «130»
51
Section
Available accessories
3 Press MULTI-CONTROL to display entries.
The display shows the first three Phone Book
entries starting with that letter (e.g. “Ben”,
“Brian” and “Burt” when “B” is selected).
4 Push MULTI-CONTROL up or down to
select a Phone Book entry you want to call.
5 Push MULTI-CONTROL right to display
the detailed list of the selected entry.
The phone number, name and genre (if assigned) of entries are displayed in the detailed
list.
Press MULTI-CONTROL to make a call.
0.
7 To end the call, push MULTI-CONTROL
down.
Editing the name of a Phone Book entry
13
Important
Be sure to park your vehicle and apply the parking brake when performing this operation.
You can edit the names of Phone Book entries.
Each name can be up to 16 characters long.
1 Display the detailed list of your desired
Phone Book entry.
See step 1 to 5 on Calling a number in the
phone book on the previous page for how to do
this.
2 Press and hold MULTI-CONTROL to display the name input screen.
Edit name is displayed.
3 Press DISP to select the desired character type.
Each press of DISP switches the character
types in the following order:
52
4 Push MULTI-CONTROL up or down to
select a letter.
# To delete a character and leave a space, select
“_” (underbar).
5 Push MULTI-CONTROL left or right to
move the cursor to the previous or next
character position.
6 Press MULTI-CONTROL to store the new
name.
Editing phone numbers
co
6
# Pressing and holding DISP enables you to
switch character set between ISO8859-1 (European characters) and ISO8859-5 (Russian characters) alternately.
# European characters and Russian characters
can’t be mixed.
m
# You can scroll the name and phone number
by pressing and holding DISP.
# If several phone numbers are entered to an
entry, select one by turning MULTI-CONTROL.
# If you want to go back and select another
entry, push MULTI-CONTROL left.
Alphabet (upper case), numbers and symbols
—alphabet (lower case)—numbers and symbols—European characters, such as those
with accents (e.g., á, à, ä, ç) or Russian characters
a
2 Push MULTI-CONTROL left or right to
select the first letter of the name you are
looking for.
.u
06
Important
Be sure to park your vehicle and apply the parking brake when performing this operation.
You can edit the numbers of Phone Book entries. Each phone number can be up to 24 digits long.
1 Display the detailed list of your desired
Phone Book entry.
See step 1 to 5 on Calling a number in the
phone book on the previous page for how to do
this.
2 Press and hold MULTI-CONTROL to display the name input screen.
Edit name is displayed.
3 Turn MULTI-CONTROL to switch to the
number input screen.
Edit name (name input screen)—
Edit number (number input screen)—
Clear memory (clear memory screen)
4 Push MULTI-CONTROL left or right to
move the cursor to the number you want
to change.
En
Autogood products «130»
Section
Available accessories
06
Clearing a phone book entry
Important
1 Display the detailed list of your desired
Phone Book entry.
See step 1 to 5 on Calling a number in the
phone book on page 51 for how to do this.
2 Turn MULTI-CONTROL to select a phone
number.
Turning MULTI-CONTROL to change the
phone numbers stored in the list.
# If the number is already in the phone book,
the name is displayed.
# You can also change the phone number by
pushing MULTI-CONTROL up or down.
3 Push MULTI-CONTROL right to display
the detailed list.
Name and phone number are displayed in the
detailed list.
m
2 Press and hold MULTI-CONTROL to display the name input screen.
Edit name is displayed.
# For more details about the Phone Book list,
refer to Using the phone book on page 51.
# If no phone numbers are stored in the selected list, No data is displayed.
0.
co
3 Turn MULTI-CONTROL to switch to the
clear memory screen.
Edit name (name input screen)—
Edit number (number input screen)—
Clear memory (clear memory screen)
Available accessories
Be sure to park your vehicle and apply the parking brake when performing this operation.
1 Press LIST to display the list.
Press LIST repeatedly to switch between the
following lists:
Phone book—Missed call—Dialled call—Received call
a
6 Press MULTI-CONTROL to store the new
number.
tory. You can browse the call history and call
numbers from it.
.u
5 Push MULTI-CONTROL up or down to
change numbers.
Repeat these steps until you have finished
changing.
13
4 Push MULTI-CONTROL right to show a
confirmation display.
Clear memory YES is displayed.
# If you do not want to clear memory that you
have selected, push MULTI-CONTROL left. The
display reverts.
5 Press MULTI-CONTROL to delete the
Phone Book entry.
Cleared is displayed.
The Phone Book entry is deleted. The display
returns to Phone Book entry list.
# If the number is already in the Phone Book
then the name is also displayed.
# Turning MULTI-CONTROL switches to the previous or next phone number diplayed in the detailed list.
# If you do not operate anything within about 30
seconds, the list display is canceled automatically.
4
Press MULTI-CONTROL to make a call.
# For an international call, press and hold
MULTI-CONTROL to add + to the phone number.
5 To end the call, push MULTI-CONTROL
down.
Using preset numbers
Using the call history
Important
Important
Be sure to park your vehicle and apply the parking brake when performing this operation.
Be sure to park your vehicle and apply the parking brake when performing this operation.
The 12 most recent calls made (dialled), received and missed, are stored in the call his-
Numbers that you dial frequently can be assigned to presets for quick recall.
En
Autogood products «130»
53
Section
06
Available accessories
1 Select a desired phone number from
the phone book or the call history. Or directly enter a desired phone number.
To select a desired phone number from the
Phone Book or the Call History, see the instructions explained in previous pages. To directly enter a desired phone number, see
Making a call by entering phone number on
this page.
2 Use MULTI-CONTROL to select
Clear memory in the function menu.
3 Push MULTI-CONTROL up or down to
select an item.
Each time MULTI-CONTROL is pushed up or
down, the items are switched in the following
order:
Phone book (phone book)—Missed calls
(missed call history)—Dialed calls (dialled
call history)—Received calls (received call history)—Dial preset (preset phone numbers)—
All clear (delete all memory)
# If you want to clear all the Phone Book,
dialled/received/missed call history list and preset phone number, select All clear.
# If guest phone is connected to this unit via
Bluetooth wireless technology, Phone book cannot be selected.
m
.u
Making a call by entering
phone number
Important
1 Display the function menu.
Refer to Function and operation on page 48.
a
2 Press and hold one of 1 to 6 on the remote control to store the phone number.
The selected phone number has been stored
in memory. The next time you press the same
preset button, the phone number is recalled
from memory.
Clearing memory
4 Push MULTI-CONTROL right to determine the item that you want to delete
from this unit.
Clear memory YES is displayed. Clearing
memory is now on standby.
co
Be sure to park your vehicle and apply the parking brake when performing this operation.
1 Display the function menu.
Refer to Function and operation on page 48.
0.
2 Use MULTI-CONTROL to select
Number dial in the function menu.
13
# You can also enter in this menu from the
standby display by pressing DIRECT on the remote control.
3 Push MULTI-CONTROL up or down to
select a number.
# You can also input numbers by pressing 0 to 9
on the remote control.
4 Push MULTI-CONTROL left or right to
move the cursor to the previous or next position.
# Up to 24 digits can be entered.
5 When you completed entering the
number, press MULTI-CONTROL.
Call confirmation appears.
6 Press MULTI-CONTROL again to make a
call.
7 To end the call, push MULTI-CONTROL
down.
54
# If you do not want to clear memory that you
have selected, push MULTI-CONTROL left. The
display reverts.
5 Press MULTI-CONTROL to clear the
memory.
Cleared is displayed and data on the selected
item is cleared from this unit’s memory.
Setting automatic rejecting
1 Display the function menu.
Refer to Function and operation on page 48.
2 Use MULTI-CONTROL to select
Refuse calls in the function menu.
3 Press MULTI-CONTROL to turn automatic call rejection on.
# To turn automatic call rejection off, press
MULTI-CONTROL again.
En
Autogood products «130»
Section
Available accessories
06
1
Setting automatic answering
2
1 Display the function menu.
Refer to Function and operation on page 48.
2 Use MULTI-CONTROL to select
Auto answer in the function menu.
3 Press MULTI-CONTROL to turn automatic answering on.
3
# To turn automatic answering function off,
press MULTI-CONTROL again.
Switching the ring tone
% Select a disc
Push MULTI-CONTROL up or down.
# You can also select a disc by using 1 to 6 buttons on the remote control.
! For discs 1 to 6, press the corresponding
button number.
! For discs 7 to 12, press and hold the corresponding numbers, such as 1 for disc 7,
until the disc number appears in the display.
2 Use MULTI-CONTROL to select
Ring tone in the function menu.
m
3 Press MULTI-CONTROL to turn the ring
tone on.
.u
a
1 Display the function menu.
Refer to Function and operation on page 48.
% Fast forward or reverse
Push and hold MULTI-CONTROL left or right.
co
# To turn the ring tone off, press
MULTI-CONTROL again.
Available accessories
1 Disc number indicator
2 Track number indicator
3 Play time indicator
Echo canceling and noise reduction
0.
1 Use MULTI-CONTROL to select
Echo cancel in the function menu.
13
2 Press MULTI-CONTROL to turn echo canceling on.
# To turn echo canceling off, press
MULTI-CONTROL again.
Multi-CD Player
Basic Operations
You can use this unit to control a multi-CD
player, which is sold separately.
! Only functions described in this manual are
supported by 50-disc multi-CD players.
! This unit is not designed to operate disc title
list functions with a 50-disc multi-CD player.
For information about the disc title list functions, refer to Selecting discs from the disc
title list on page 58.
% Select a track
Push MULTI-CONTROL left or right.
Notes
! When multi-CD player completes preparatory
operations, READY is displayed.
! If an error message such as ERROR-11 is displayed, refer to the multi-CD player owner’s
manual.
! If there are no discs in the multi-CD player magazine, No disc is displayed.
Using CD TEXT functions
You can use these functions only with a CD
TEXT compatible multi-CD player.
The operation is the same as that of the builtin CD player.
Refer to Displaying text information on disc on
page 19.
En
Autogood products «130»
55
Section
06
Available accessories
Introduction of advanced
operations
Function name
Operation
Play mode
Refer to Selecting a repeat play
range on page 20.
However, the repeat play ranges
you can select are different from
that of the built-in CD player. The
repeat play ranges of the multi-CD
player are:
! M-CD repeat – Repeat all
discs in the multi-CD player
! Track repeat – Repeat just the
current track
! Disc repeat – Repeat the current disc
Random mode
Refer to Playing tracks in random
order on page 21.
You can only use Compression (compression
and DBE) with a multi-CD player that supports
them.
1 Press MULTI-CONTROL to display the
main menu.
Pause
TitleInput "A"
13
0.
co
# If you do not operate functions other than
ITS memo and TitleInput "A" within about 30
seconds, the display automatically returns to the
ordinary display.
# When playing a CD TEXT disc on a CD TEXT
compatible multi-CD player, you cannot switch to
TitleInput "A". The disc title is already recorded
on the CD TEXT disc.
Function and operation
Play mode, Random mode, Scan mode,
Pause and TitleInput "A" operations are basically the same as that of the built-in CD player.
Refer to Scanning folders and
tracks on page 21.
.u
Scan mode
m
3 Turn MULTI-CONTROL to select the
function.
Play mode (repeat play)—Random mode
(random play)—Scan mode (scan play)—
Pause (pause)—compression (compression
and DBE)—ITS play mode (ITS play)—
ITS memo (ITS programming)—
TitleInput "A" (disc title input)
a
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
The function menu is displayed.
Refer to Pausing playback on page
21.
Refer to Entering disc titles on
page 22.
Notes
! You can also select the function by pressing
FUNCTION on the remote control.
! To return to the playback display, press BAND.
! If you select other discs during repeat play,
the repeat play range changes to
M-CD repeat.
! If you perform track search or fast forward/reverse during Track repeat, the repeat play
range changes to Disc repeat.
! After track or disc scanning is finished, normal playback of the tracks begins again.
Using compression and bass
emphasis
You can only use these functions with a multiCD player that supports them.
COMP (compression) and DBE (dynamic bass
emphasis) functions lets you adjust the sound
playback quality of the multi-CD player.
1 Display the function menu.
Refer to Introduction of advanced operations on
this page.
56
En
Autogood products «130»
Section
Available accessories
06
2 Use MULTI-CONTROL to select
compression in the function menu.
Playback from your ITS playlist
# If the multi-CD player does not support
COMP/DBE, NO COMP is displayed when you attempt to select it.
ITS play lets you listen to the tracks that you
have entered into your ITS playlist. When you
turn on ITS play, tracks from your ITS playlist
in the multi-CD player begin to play.
3 Press MULTI-CONTROL to select your favorite setting.
COMP OFF—COMP 1—COMP 2—
COMP OFF—DBE 1—DBE 2
1 Select the repeat range.
Refer to Playing tracks in random order on
page 21.
3 Use MULTI-CONTROL to select
ITS play mode in the function menu.
.u
a
4 Press MULTI-CONTROL to turn ITS play
on.
ITS play appears in the display. Playback begins of those tracks from your playlist within
the previously selected M-CD repeat or
Disc repeat ranges.
m
ITS (instant track selection) lets you make a
playlist of favorite tracks from the multi-CD
player magazine. After you have added your favorite tracks to the playlist, you can turn on ITS
play and play just those selections.
You can use ITS to enter and play back up to
99 tracks per disc from up to 100 discs (with
the disc titles). (With multi-CD players sold before the CDX-P1250 and CDX-P650, up to 24
tracks can be stored in the playlist.)
co
# If no tracks in the current range are programmed for ITS play, then ITS empty is displayed.
# To turn ITS play off, press MULTI-CONTROL
again.
Available accessories
Using ITS playlists
2 Display the function menu.
Refer to Introduction of advanced operations on
the previous page.
Creating a playlist with ITS programming
0.
1 Play a CD that you want to program.
Push MULTI-CONTROL up or down to select
the CD.
13
2 Display the function menu.
Refer to Introduction of advanced operations on
the previous page.
3 Use MULTI-CONTROL to select
ITS memo in the function menu.
4 Select the desired track by pushing
MULTI-CONTROL left or right.
5 Push MULTI-CONTROL up to store the
currently playing track in the playlist.
Memory complete is displayed and the currently playing selection is added to your playlist.
6 Press BAND to return to the playback
display.
Erasing a track from your ITS playlist
You can delete a track from your ITS playlist if
ITS play is on.
If ITS play is already on, skip to step 2. If ITS
play is not already on, use MULTI-CONTROL.
1 Play the CD with the track you want to
delete from your ITS playlist, and turn ITS
play on.
Refer to Playback from your ITS playlist on this
page.
2 Display the function menu.
Refer to Introduction of advanced operations on
the previous page.
3 Use MULTI-CONTROL to select
ITS memo in the function menu.
4 Select the desired track by pushing
MULTI-CONTROL left or right.
Note
After data for 100 discs is stored in memory, data
for a new disc will overwrite the oldest one.
En
Autogood products «130»
57
Section
Available accessories
# If there are no tracks from your playlist in the
current range, ITS empty is displayed and normal playback resumes.
6 Press BAND to return to the playback
display.
Erasing a CD from your ITS playlist
You can delete all tracks of a CD from your ITS
playlist if ITS play is off.
1 Play the CD that you want to delete.
Push MULTI-CONTROL up or down to select
the CD.
% Press DISP to select the desired text information.
! For title entered CD
Play time— : disc title and play time
! For CD TEXT discs
Play time— : disc artist name and :
track title— : disc artist name and :
disc title— : disc title and : track title
— : track artist name and : track title
— : track title and play time
Selecting discs from the disc title list
Disc title list lets you see the list of disc titles
entered in the multi-CD player and select one
of them to play back.
co
3 Use MULTI-CONTROL to select
ITS memo in the function menu.
Displaying disc titles
m
2 Display the function menu.
Refer to Introduction of advanced operations on
page 56.
! Titles remain in the memory even after the
disc is removed from the magazine, and
are recalled when the disc is reinserted.
! After data for 100 discs is stored in memory, data for a new disc will overwrite the
oldest one.
a
5 Push MULTI-CONTROL down to erase
the track from your ITS playlist.
The currently playing selection is erased from
your ITS playlist and playback of the next track
begins.
.u
06
13
0.
4 Push MULTI-CONTROL down to erase
all tracks on the currently playing CD from
your ITS playlist.
All tracks on the currently playing CD are deleted from your playlist and Memory deleted
is displayed.
5 Press BAND to return to the playback
display.
Using disc title functions
You can input CD titles and display the titles.
Then, you can easily search for and play a desired disc.
Entering disc titles
Use the disc title input feature to store up to
100 CD titles (with ITS playlist) into the multiCD player. Each title can be up to 10 characters long.
For details concerning operation, refer to Entering disc titles on page 22.
58
1 Press LIST to switch to the disc title list
mode during the playback display.
2 Use MULTI-CONTROL to select the desired disc title.
Turn to change the disc title. Press to play.
# You can also change the disc title by pushing
MULTI-CONTROL up or down.
# When playing CD TEXT disc, push
MULTI-CONTROL right to see a list of the tracks
in the selected disc. Push MULTI-CONTROL left
to return to the disc list.
# If no title is entered for a disc, No Title is displayed.
# No disc is displayed next to the disc number
when there is no disc in the magazine.
# If you do not operate the list within about 30
seconds, the display automatically returns to the
ordinary display.
En
Autogood products «130»
Section
Available accessories
06
DVD Player
Selecting a disc
Basic Operations
! You can operate this function only when a
multi-DVD player is connected to this unit.
You can use this unit to control a DVD player or
multi-DVD player, which is sold separately.
For details concerning operation, refer to the
DVD player’s or multi-DVD player’s operation
manual. This section provides information on
DVD operations with this unit which differs
from that described in the DVD player’s or
multi-DVD player’s operation manual.
3
4
! You can operate this function only when a
DVD player compatible with compressed
audio playback is connected to this unit.
% Push MULTI-CONTROL up or down to
select a folder.
a
2
Selecting a folder
.u
Introduction of advanced
operations
1 Press MULTI-CONTROL to display the
main menu.
m
5
2 Use MULTI-CONTROL to select
FUNCTION.
Turn to change the menu option. Press to select.
The function menu is displayed.
13
0.
co
1 DVD-V/VCD/CD/MP3/WMA indicator
Shows the type of disc currently playing.
2 Disc number indicator
Shows the number of the disc currently playing when using a multi-DVD player.
3 Title/Folder number indicator
Shows the title (when playing DVD video) or
folder (when playing compressed audio) of
the selection currently playing.
4 Chapter/track number indicator
Shows the chapter (when playing DVD video)
or track (when playing Video CD, CD or compressed audio) currently playing.
5 Play time indicator
Available accessories
1
% Press any of 1 to 6 on the remote control to select the desired disc.
% Select a chapter/track
Push MULTI-CONTROL left or right.
% Fast forward or reverse
Push and hold MULTI-CONTROL left or right.
# When playing compressed audio, there is no
sound on fast forward or reverse.
% To skip back or forward to another
chapter/track, push MULTI-CONTROL left or
right.
3 Turn MULTI-CONTROL to select the
function.
During DVD video or Video CD playback
Play mode (repeat play)—Pause (pause)
During CD playback
Play mode (repeat play)—Random mode
(random play)—Scan mode (scan play)—
Pause (pause)—ITS play mode (ITS play)—
ITS memo (ITS input)—TitleInput "A" (disc
title input)
During compressed audio playback
Play mode (repeat play)—Random mode
(random play)—Scan mode (scan play)—
Pause (pause)
# You can also select the function by pressing
FUNCTION on the remote control.
# To return to the playback display, press BAND.
En
Autogood products «130»
59
Section
Available accessories
Function and operation
Play mode, Random mode, Scan mode,
Pause and TitleInput "A" operations are basically the same as that of the built-in CD player.
Also, ITS play mode and ITS memo operations are basically the same as that the multiCD player.
Operation
Play mode
Refer to Selecting a repeat play
range on page 20.
But the repeat play range that you
can select is vary depending on
the type of disc or system. The repeat play ranges of the DVD
player/multi-DVD player are as
below:
During PBC playback of Video
CDs, this function cannot be operated.
! Disc repeat – Repeat the current disc
! Folder repeat – Repeat the
current folder
! Title repeat – Repeat just the
current title
! Chapter repeat – Repeat just
the current chapter
! Track repeat – Repeat the current track
! If you select other discs during repeat play,
the repeat play range changes to Disc repeat.
! When playing back Video CD or CD, if you perform track search or fast forward/reverse during Track repeat, the repeat play range
changes to Disc repeat.
! When playing back compressed audio, if you
select another folder during repeat play, the
repeat play range changes to Disc repeat.
! When playing back compressed audio, if you
perform track search or fast forward/reverse
during Track repeat, the repeat play range
changes to Folder repeat.
! Multi-DVD player that has ITS functions and
disc title functions can also be connected to
this unit. In this case, ITS play mode,
ITS memo and disc title input can be controlled.
! The ITS function of a DVD player differs
slightly from ITS playback with a multi-CD
player. With multi-DVD player, ITS playback applies only to the CD playing. For details, refer
to Using ITS playlists on page 57.
13
0.
co
m
Function name
Notes
a
# If you do not operate functions except for
ITS memo and TitleInput "A" within about 30
seconds, the display is automatically returned to
the ordinary display.
.u
06
Random mode
Refer to Playing tracks in random
order on page 21.
Scan mode
Refer to Scanning folders and
tracks on page 21.
Pause
Refer to Pausing playback on page
21.
ITS play mode
Refer to Using ITS playlists on
page 57.
ITS memo
Refer to Using ITS playlists on
page 57.
TitleInput "A"
Refer to Entering disc titles on
page 22.
TV tuner
Basic Operations
You can use this unit to control a TV tuner,
which is sold separately.
For details concerning operation, refer to the
TV tuner’s operation manual. This section provides information on TV operations with this
unit, which differs from that described in the
TV tuner’s operation manual.
1
3
1 Band indicator
60
2
En
Autogood products «130»
Section
Available accessories
06
2 Preset number indicator
3 Channel indicator
Using the remote control
You can also store and recall stations assigned
to preset tuning numbers P 1 to P 6 by using
the remote control.
% Seek tuning
Push and hold MULTI-CONTROL left or right
for about one second and release.
# You can also recall stations assigned to preset
tuning numbers by pushing MULTI-CONTROL up
or down during the channel display.
m
Storing the strongest broadcast
stations sequentially
You can easily store up to 12 broadcast stations for later recall.
! 12 stations for each band can be stored in
memory.
1 Press MULTI-CONTROL to display the
main menu.
1 Press LIST.
Preset screen is displayed.
# You can also select the function by pressing
FUNCTION on the remote control.
2 Use MULTI-CONTROL to store the selected station in memory.
Turn to change the preset number. Press and
hold to store.
3 Press MULTI-CONTROL to turn BSSM
on.
Searching begins to flash. While Searching is
flashing, the 12 strongest broadcast stations
are stored in order from the lowest channel
up. When finished, the preset channel list appears.
13
0.
co
Storing and recalling broadcast
stations
Available accessories
Notes
! Band can be selected from TV-1 or TV-2.
! You can cancel seek tuning by pushing
MULTI-CONTROL left or right.
! If you push and hold MULTI-CONTROL left or
right, you can skip stations. Seek tuning starts
as soon as you release MULTI-CONTROL.
% When you find a station that you want
to store in memory, press one of preset
tuning buttons 1 to 6 and hold until the
preset number stops flashing.
The number you have pressed will flash in the
preset number indicator and then remain lit.
The selected station has been stored in memory.
The next time you press the same preset tuning button the station is recalled from memory.
a
% Select a channel (step by step)
Push MULTI-CONTROL left or right.
.u
% Select a band
Press BAND.
# You can also store the station in memory by
pushing and holding MULTI-CONTROL right.
2 Use MULTI-CONTROL and select
FUNCTION to display BSSM.
3 Use MULTI-CONTROL to select the desired station.
Turn to change the station. Press to select.
# To cancel the storage process, press
MULTI-CONTROL again.
# You can also change the station by pushing
MULTI-CONTROL up or down.
# If you do not operate the list within about 30
seconds, the display automatically returns to the
ordinary display.
4 Use MULTI-CONTROL to select the desired station.
Turn to change the station. Press to select.
# You can also change the station by pushing
MULTI-CONTROL up or down.
# To return to the ordinary display, press BAND.
En
Autogood products «130»
61
Section
06
Available accessories
13
0.
co
m
.u
a
# If you do not operate the list within about 30
seconds, the display automatically returns to the
ordinary display.
62
En
Autogood products «130»
Appendix
Additional Information
Error messages
When you contact your dealer or your nearest
Pioneer Service Center, be sure to have the
error message recorded.
Play an audio file
not protected by
Windows Media
DRM 9/10.
PROTECT
All the files on
the connected
USB portable
audio player/
USB memory are
protected by
Windows Media
DRM 9/10
Transfer audio files
not protected by
Windows Media
DRM 9/10 to the
USB portable
audio player/USB
memory and connect.
N/A USB
The USB device
connected to is
not supported by
this unit.
Connect a USB
portable audio
player or USB
memory that is
USB Mass Storage
Class compliant.
Built-in CD Player
Cause
Action
ERROR-11, 12, Scratched disc
17, 30
Replace disc.
ERROR-10, 11, Electrical or me12, 15, 17, 30, chanical
A0
Turn the ignition
switch OFF and
back ON, or switch
to a different
source, then back
to the CD player.
ERROR-22, 23
Replace disc.
The CD format
cannot be played
back
No audio
The inserted disc Replace disc.
does not contain
any files that can
be played back
m
The inserted disc Replace disc.
does not contain
any data
CHECK USB
0.
co
ERROR-15
.u
Clean disc.
a
Message
ERROR-11, 12, Dirty disc
17, 30
The inserted disc Replace disc.
contains WMA
files that are protected by DRM
PROTECT
Replace disc.
All the files on
the inserted disc
are secured by
DRM
13
TRK SKIPPED
The USB connec- Confirm that the
tor or USB cable USB connector or
is short-circuited. USB cable is not
caught in something or damaged.
The connected
USB portable
audio player/
USB memory
consumes more
than 500 mA
(maximum allowable current).
Additional Information
The connected
USB portable
audio player/
USB memory
contains WMA
files that are protected by
Windows Media
DRM 9/10
TRK SKIPPED
Disconnect the
USB portable
audio player/USB
memory and do
not use it. Turn the
ignition switch to
OFF, then to ACC
or ON and then
connect the compliant USB portable audio player/
USB memory.
USB audio player/USB memory
Message
Cause
Action
No audio
No songs
Transfer the audio
files to the USB
portable audio
player/USB memory and connect.
USB memory
with security enabled is connected
Follow the USB
memory instructions to disable the
security.
No songs
Transfer the songs
to iPod.
En
Autogood products «130»
63
Appendix
Additional Information
USB device is
not formatted
with FAT16 or
FAT32
Perform one of the
following operations.
-Turn the ignition
switch OFF and
back ON.
-Disconnect the
USB portable
audio player/USB
memory.
-Change to a different source.
Then, return to the
USB portable
audio player/USB
memory.
ERROR-A1
CHECK USB
iPod is not
charged but operates correctly
Check if the connection cable for
iPod shorted out
(e.g., not caught in
metal objects).
After checking,
turn the ignition
switch OFF and
back ON or disconnect the iPod and
connect again.
No Songs
No songs
Transfer the songs
to iPod.
STOP
No songs in the
current list
Select a list that
contains the
songs.
USB device should
be formatted with
FAT16 or FAT32.
a
ERROR-23
Communication
failure
.u
ERROR-19
Handling guideline of discs
and player
iPod
Cause
Action
Communication
failure
Disconnect the
cable from iPod.
Once iPod main
menu is displayed,
connect the cable
again.
Reset the iPod.
m
Message
ERROR-19
Disconnect the
cable from iPod.
Once iPod main
menu is displayed,
connect the cable
again.
Reset the iPod.
13
iPod failure
0.
co
! Use only discs featuring either of following
two logos.
N/A USB
ERROR-16
64
Old version of
iPod
Update the iPod
version.
iPod failure
Reset the iPod.
Old version of
iPod
Update the iPod
version.
iPod failure
Disconnect the
cable from iPod.
Once iPod main
menu is displayed,
connect the cable
again.
Reset the iPod.
! Use only conventional, fully circular discs.
Do not use shaped discs.
! Use 12-cm or 8-cm CD. Do not use an
adapter when playing 8-cm CDs.
! Do not insert anything other than a CD into
the CD loading slot.
! Do not use cracked, chipped, warped, or
otherwise damaged discs as they may damage the player.
! Unfinalized CD-R/CD-RW disc playback is
not possible.
! Do not touch the recorded surface of the
discs.
! Store discs in their cases when not in use.
En
Autogood products «130»
Appendix
Additional Information
Compressed audio
compatibility
WMA
! Compatible format: WMA encoded by
Windows Media Player
! Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps
to 384 kbps (VBR)
! Sampling frequency: 32 kHz to 48 kHz
! Windows Media Audio 9 Professional, Lossless, Voice: No
m
.u
a
MP3
! Bit rate: 8 kbps to 320 kbps
! Sampling frequency: 16 kHz to 48 kHz (32,
44.1, 48 kHz for emphasis)
! Compatible ID3 tag version: 1.0, 1.1, 2.2,
2.3, 2.4 (ID3 tag Version 2.x is given priority
than Version 1.x.)
! M3u playlist: No
! MP3i (MP3 interactive), mp3 PRO: No
co
Dual Discs
AAC
! Compatible format: AAC encoded by
iTunes®
! Sampling frequency: 11.025 kHz to 48 kHz
! Transmission rate: 16 kbps to 320 kbps
! Apple Lossless: No
13
0.
! Dual Discs are two-sided discs that have a
recordable CD for audio on one side and a
recordable DVD for video on the other.
! Since the CD side of Dual Discs is not physically compatible with the general CD
standard, it may not be possible to play the
CD side with this unit.
! Frequent loading and ejecting of a Dual
Disc may result in scratches on the disc.
Serious scratches can lead to playback problems on this unit. In some cases, a Dual
Disc may become stuck in the disc loading
slot and will not eject. To prevent this, we
recommend you refrain from using Dual
Disc with this unit.
! Please refer to the information from the
disc manufacturer for more detailed information about Dual Discs.
Additional Information
! Avoid leaving discs in excessively hot environments including under direct sunlight.
! Do not attach labels, write on or apply chemicals to the surface of the discs.
! To clean a CD, wipe the disc with a soft
cloth outward from the center.
! Condensation may temporarily impair the
player’s performance. Leave it to adjust to
the warmer temperature for about one
hour. Also, wipe any dump discs with a soft
cloth.
! Playback of discs may not be possible because of disc characteristics, disc format,
recorded application, playback environment, storage conditions, and so on.
! Text information may not be correctly displayed depending on the recorded environment.
! Road shocks may interrupt disc playback.
! Read the precautions for discs before
using them.
WAV
! Compatible format: Linear PCM (LPCM),
MS ADPCM
! Quantization bits: 8 and 16 (LPCM), 4 (MS
ADPCM)
! Sampling frequency: 16 kHz to 48 kHz
(LPCM), 22.05 kHz to 44.1 kHz (MS ADPCM)
USB audio player/USB memory
USB audio player/USB memory
compatibility
! USB version: 2.0, 1.1 and 1.0
! USB data transfer rate: full speed
! USB Class: MSC (Mass Storage Class) device
En
Autogood products «130»
65
Appendix
Additional Information
Notes
0.
co
m
! Partitioned USB memory is not compatible
with this unit.
! Depending on the kind of USB portable audio
player/USB memory you use, this unit may
not recognize the USB audio player/USB
memory or audio files may not be played back
properly.
! This unit can play back files in the USB portable audio player/USB memory that is USB
Mass Storage Class. However, copyright protected files that are stored in above-mentioned
USB devices cannot be played back. (If the
iPod is connected to this unit, file playback
condition depends on the iPod specifications.)
! You cannot connect a USB portable audio
player/USB memory to this unit via a USB
hub.
! Depending on the USB devices connected
to this unit, it may generate noise in the
radio.
! Only 32 characters from the beginning can
be displayed as a file name (including the
extension) or a folder name when USB portable audio player/USB memory is selected
as a source.
! The text information of some audio files
may not be correctly displayed.
! File extensions must be used properly.
! Up to 15 000 files on a USB portable audio
player/USB memory can be played back.
! Up to 500 folders on a USB portable audio
player/USB memory can be played back.
! Up to eight tiers directory on a USB portable audio player/USB memory can be
played back.
! There may be a slight delay when starting
playback of audio files on a USB portable
audio player/USB memory with numerous
folder hierarchies.
! Do not connect anything other than the
USB portable audio player/USB memory.
! Operations may vary depending on the
kind of USB audio player and a USB memory.
a
Protocol: bulk
Minimum amount of memory: 250 MB
Maximum amount of memory: 250 GB
File system: FAT32 and FAT16
Supply current: 500 mA
.u
!
!
!
!
!
13
Handling guideline and
supplemental information
! Do not leave the USB portable audio
player/USB memory in direct sunlight for
extended amounts of time. Extended exposure to direct sunlight can result in USB
portable audio player/USB memory malfunction due to the resulting high temperature.
! Do not leave the USB portable audio
player/USB memory in high temperature.
! Firmly secure the USB portable audio
player/USB memory when driving. Do not
let the USB portable audio player/USB
memory fall onto the floor, where it may become jammed under the brake or accelerator pedal.
! There may be a slight delay when starting
playback of audio files encoded with image
data.
66
The sequence of audio files on USB
memory
For USB portable audio players, the sequence is
different from that of USB memory and depends on the player.
En
Autogood products «130»
Appendix
Additional Information
! Do not leave the iPod in a high temperature.
! Connect directly the dock connector cable
to the iPod so that this unit works properly.
! Firmly secure the iPod when driving. Do
not let the iPod fall onto the floor, where it
may become jammed under the brake or
accelerator pedal.
! For details, refer to the iPod’s manuals.
Example of a hierarchy
: Folder
: Compressed audio file
1
2
3
4
About iPod settings
Level 2
Level 3
Level 4
0.
co
m
! 01 to 05 represent assigned folder numbers. 1 to 6 represent the playback sequence. The user cannot assign folder
numbers and specify the playback sequence with this unit.
! Playback sequence of the audio file is the
same as recorded sequence in the USB device.
! To specify the playback sequence, the following method is recommended.
a
Level 1
! You cannot operate the iPod Equalizer on
Pioneer products. We recommend that you
set the iPod Equalizer to off, before connecting to this unit.
! You cannot set Repeat to off on the iPod
when using this unit. Even if you set Repeat
to off on the iPod, Repeat is automatically
changed to All when connecting the iPod
to this unit.
13
1 Create the file name including numbers
that specify the playback sequence (e.g.,
001xxx.mp3 and 099yyy.mp3).
2 Put those files into a folder.
3 Record the folder containing files into the
USB device.
However, depending on the system environment, you cannot specify the file playback
sequence.
iPod
About handling the iPod
! Do not leave the iPod in direct sunlight for
extended amounts of time. Extended exposure to direct sunlight can result in iPod
malfunction due to the resulting high temperature.
Compressed audio files on
the disc
Additional Information
6
.u
5
! Depending on the version of Windows
Media Player used to encode WMA files,
album names and other text information
may not be correctly displayed.
! There may be a slight delay when starting
playback of WMA/AAC files encoded with
image data.
! ISO 9660 Level 1 and 2 compliant. Romeo
and Joliet file systems are both compatible
with this player.
! Multi-session playback is possible.
! Compressed audio files are not compatible
with packet write data transfer.
! Only 64 characters from the beginning can
be displayed as a file name (including the
extension such as .wma, .mp3, .m4a or
.wav) or a folder name.
! Folder selection sequence or other operation may be altered depending on the encoding or writing software.
En
Autogood products «130»
67
Appendix
Example of a hierarchy
0.
co
: Folder
: Compressed audio file
.u
m
! Regardless of the length of blank section
between the songs of original recording,
compressed audio discs play with a short
pause between songs.
! File extensions such as .wma, .mp3, .m4a
or .wav must be used properly.
! Russian text to be displayed on this unit
should be encoded with the following character sets:
— Unicode (UTF-8, UTF-16)
— Character sets other than Unicode that
are used in Windows environment and
are set to Russian in the multi-language
setting
! Only 32 characters from the beginning can
be displayed as a file name (including the
extension such as .wma, .mp3, .m4a or
.wav) or a folder name when using Russian
text.
a
Additional Information
1
13
2
3
5
4
6
Level 1
Level 2
Level 3
Level 4
! This unit assigns folder numbers. The user
cannot assign folder numbers.
! Folder hierarchy is allowed up to eight tiers.
However, a practical hierarchy of folder is
less than two tiers.
! Up to 99 folders on a disc can be played
back.
68
En
Autogood products «130»
Appendix
Additional Information
Audio
Specification .............................. USB 2.0 full speed
Supply current .......................... 500 mA
Maximum amount of memory
..................................................... 250 GB
File system .................................. FAT16, FAT32
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
AAC decoding format ............ MPEG-4 AAC (iTunes® encoded only) (.m4a)
(Ver. 7.2 and earlier)
WAV signal format .................. Linear PCM & MS ADPCM
(Non-compressed)
FM tuner
m
Maximum power output ....... 50 W × 4
50 W × 2/4 W + 70 W × 1/2
W (for subwoofer)
Continuous power output ... 22 W × 4 (50 Hz to 15 000
Hz, 5% THD, 4 W load, both
channels driven)
Load impedance ...................... 4 W to 8 W × 4
4 W to 8 W × 2 + 2 W × 1
Preout max output level ....... 4 V
Equalizer (7-Band Graphic Equalizer):
Frequency .......................... 50/125/315/800/2k/5k/12.5k
Hz
Gain ...................................... ±12 dB
HPF:
Frequency .......................... 50/63/80/100/125 Hz
Slope .................................... –12 dB/oct
Subwoofer (mono):
Frequency .......................... 50/63/80/100/125 Hz
Slope .................................... –18 dB/oct
Gain ...................................... +6 dB to –24 dB
Phase .................................. Normal/Reverse
Bass boost:
Gain ...................................... +12 dB to 0 dB
USB
13
0.
co
Frequency range ...................... 87.5 MHz to 108.0 MHz
Usable sensitivity ..................... 8 dBf (0.7 µV/75 W, mono,
S/N: 30 dB)
Signal-to-noise ratio ............... 75 dB (IEC-A network)
Additional Information
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system ................... Negative type
Max. current consumption
..................................................... 10.0 A
Dimensions (W × H × D):
DIN
Chassis ..................... 180 mm × 50 mm × 165
mm
Nose ........................... 188 mm × 58 mm × 18 mm
D
Chassis ..................... 180 mm × 50 mm × 165
mm
Nose ........................... 170 mm × 45 mm × 18 mm
Weight .......................................... 1.5 kg
a
General
AAC decoding format ............ MPEG-4 AAC (iTunes® encoded only) (.m4a)
(Ver. 7.2 and earlier)
WAV signal format .................. Linear PCM & MS ADPCM
(Non-compressed)
.u
Specifications
MW tuner
Frequency range ...................... 531 kHz to 1 602 kHz (9 kHz)
Usable sensitivity ..................... 18 µV (S/N: 20 dB)
Signal-to-noise ratio ............... 65 dB (IEC-A network)
LW tuner
Frequency range ...................... 153 kHz to 281 kHz
Usable sensitivity ..................... 30 µV (S/N: 20 dB)
Signal-to-noise ratio ............... 65 dB (IEC-A network)
Note
Specifications and the design are subject to modifications without notice due to improvements.
CD player
System .......................................... Compact disc audio system
Usable discs .............................. Compact disc
Signal-to-noise ratio ............... 94 dB (1 kHz) (IEC-A network)
Number of channels .............. 2 (stereo)
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
En
Autogood products «130»
69
a
.u
4-1, MEGURO 1-CHOME, MEGURO-KU
TOKYO 153-8654, JAPAN
m
PIONEER CORPORATION
co
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
0.
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium
TEL: (0) 3/570.05.11
13
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada
TEL: 1-877-283-5901
TEL: 905-479-4411
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Avila Camacho 138 10 piso
Col.Lomas de Chapultepec, Mexico, D.F. 11000
TEL: 55-9178-4270
先鋒股份有限公司
總公司 : 台北市中山北路二段44號13樓
電話 : (02) 2521-3588
先鋒電子(香港)有限公司
香港九龍尖沙咀海港城世界商業中心
9樓901-6室
電話 : (0852) 2848-6488
Published by Pioneer Corporation.
Copyright © 2007 by Pioneer Corporation.
All rights reserved.
<KOKZX> <07K00000>
<CRB2562-B/N> EW
Autogood products «130»
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising