nissan t31 x trail towbar wiring harness fitting instructions for

nissan t31 x trail towbar wiring harness fitting instructions for
FITTING INSTRUCTIONS FOR
T31 X TRAIL 08/07
TOWBAR WIRING HARNESS
PART NO. B4097-JG100AU
FITTING TIME: APPROX 45 MIN
Foam strips
50mm x 36mm
Trailer wiring Harness
A
Foam strips
50mm x 36mm
A
E
Trailer wiring Harness
X1
B
Cable tie 100mm
X10
C
X4
D
X1
B Cable tie 100mm X10
7 Pin Flat Socket
X1
Fitting Instructions
X1
FIN10018
04/11/09
ISSUE 1.3
Page 1 of 8
C
X4
D
7 Pin Flat Socket
X1
FITTING INSTRUCTIONS FOR
NISSAN T31 X TRAIL
TOWBAR WIRING HARNESS
Fitting Instructions:
1.
Remove 2 piece luggage floor board
assembly. Refer ( Fig 1A ).
2.
Remove RHS luggage drawer and if
fitted LHS luggage drawer. Refer(Fig 1B).
A
D
E
3.
Remove LHS and RHS plastic press
studs by depressing centre. Refer
( Fig 1C ).
C
B
4.
5.
Rotate both LHS and RHS locking
tabs in far corners of luggage tray. Angle
the luggage tray and carefully remove.
Remove spare wheel foam insert.
Unscrew spare wheel retainer and
remove spare wheel.
6.
Remove weather seal from LHS and
RHS and centre rear tailgate. Refer
( Fig 1D) and ( Fig 16 ) on Page 8.
Remove tailgate sill trim.
7.
Remove accessory compartment
lids from both RHS and LHS. Remove
spare wheel jack and tools from LHS
compartment.
8.
FIGURE 1
Using a 10mm socket remove both
LHS and RHS child seat restraint
anchor from rear corner trim. Refer
A
FIGURE 2
C
B
( Fig 2 A ).
A
9.
Lift rear hook assembly( Fig 3A ) and
using 10mm socket remove screws.
Repeat for opposite side.
10.
Remove cargo blind cavity trim cover
and using 10mm socket remove bolt for
LHS and RHS. Refer ( Fig 3C ).
11.
Remove overhead luggage net hook
from roof liner. Repeat for opposite side.
FIN10018
04/11/09
ISSUE 1.3
Page 2 of 8
Figure 3
FITTING INSTRUCTIONS FOR
NISSAN T31 X TRAIL
TOWBAR WIRING HARNESS
FITTING INSTRUCTIONS: Continued..
12.
Carefully pull back lower rear quarter
panel trim. Carefully pull back upper
rear quarter panel trim. Refer ( Fig 3B ).
A
24
13.
14.
15.
16.
Disconnect rear right indicator
connector. Refer ( Fig 4A ). Connect
towbar harness to vehicle harness
and to indicator holder. Refer ( Fig 5A ).
01
4J
H
40
AZ
Secure harness to vehicle body
using adhesive foam supplied.
Ensure surface is clean and free
of dirt. Refer ( Fig 5B ).
If RPA is fitted, remove yellow PVC
tape on towbar harness and connect
the RPA inhibit connector to the
module. Refer ( Fig 6A ).
Secure running length of harness to
vehicle body in corner using
adhesive foam supplied. Ensure
surface is clean and free from dirt.
Refer ( Fig 7A ).
17.
Ensuring harness is in cavity,
replace upper rear quarter panel
trim. Replace lower quarter panel trim.
18.
Secure harness to vehicle body at
either side of tailgate striker using
adhesive foam patches. Ensure
near the tailgate striker, the harness
is on the topside of the sheet metal.
Refer ( Fig 8A).
A
240
14 JH
40A
-Z
B
FIGURE 5
A
FIGURE 6
FIN10018
04/11/09
ISSUE 1.3
FIGURE 4
Page 3 of 8
FITTING INSTRUCTIONS FOR
NISSAN T31 X TRAIL
TOWBAR WIRING HARNESS
FITTING INSTRUCTIONS: Continued..
19.
20.
Carefully pull back the upper quarter
panel trim. Release the locking of
the trim from the top side of the left
rear quarter panel window section.
A
Using a 10mm socket remove the
ground terminal screw from behind
the upper quarter panel trim on the
sheet metal. Refer ( Fig 9A ).
FIGURE 7
21.
Disconnect the rear left indicator
connector. Connect towbar patch
harness to vehicle harness and to
indicator holder. Refer ( Fig 9B ).
22.
Route the white ground lead behind
the vehicle harness. Using the
ground screw, secure the towbar
harness ground lead and the other
ground terminals to the sheet
metal. Refer ( Fig 9A ).
23.
Using the cable ties provided secure
the towbar harness to the vehicle
harness in three points.
24.
Remove grommet from rear left
cavity. Feed main towbar harness
through hole. Grommet on towbar
harness will be engaged by pulling
on the other end of harness. Refer
( Fig 10A & Fig 11A).
A
FIGURE 8
B
A
FIGURE 9
FIN10018
04/11/09
ISSUE 1.3
Page 4 of 8
FITTING INSTRUCTIONS FOR
NISSAN T31 X TRAIL
TOWBAR WIRING HARNESS
FITTING INSTRUCTIONS: Continued..
25.
Raise vehicle to a safe working
height. Using a T20 Torx remove rear
left and rear right mud flaps.
26.
Remove splash guards from rear left
and right wheel wells by removing
plastic screws. Refer ( Fig 12A ).
Partially remove rear wheel arch
mouldings.
27.
Using a Philips screw driver remove
two 10mm screws from rear bumper
fascia brackets. Repeat for other
side. Refer ( Fig 1E ).
28.
FIGURE 10
Remove the two plastic screws from
the outside of the centre of the
bumper fascia. Remove the 10mm
screws from both the upper sides of
the bumper fascia. Refer ( Fig 13A ).
29.
Unclip the bumper fascia. Ensure to
disconnect both reversing lamp
connectors. If RPA is connected
disconnect both RPA sensors.
30.
Using 5 cable ties provided secure
towbar harness to vehicle harness.
Ensure harness is routed clear of
exhaust. Refer ( Fig 14A ).
31.
Wire up towbar harness to the
towbar connector. Refer table.
Secure the towbar connector to the
towbar plate. Refer ( Fig 15 ).
32.
A
A
FIGURE 11
A
Carefully replace rear bumper fascia
ensuring to reconnect the reversing
lamp connectors.
FIGURE 12
FIN10018
04/11/09
ISSUE 1.3
Page 5 of 8
FITTING INSTRUCTIONS FOR
NISSAN T31 X TRAIL
TOWBAR WIRING HARNESS
FITTING INSTRUCTIONS: Continued..
33.
34.
Replace the two 10mm screws to
the top section of the rear left and
right of the bumper fascia. Refer
( Fig 1E ). Replace the two plastic
screws to the centre of the
underside of the rear bumper fascia.
Replace the two 10mm screws for
the rear bumper fascia bracket
inside the wheel arch. Repeat for
other side. Refer ( Fig 13A ).
35.
Replace rear wheel arch moulding.
Using the two plastic rivets secure
the splash guard. Repeat for other
side.
36.
Using the three T20 Torx replace the
rear left and right mudflaps. Replace
the screw to the back underside of
the mudflap. Lower vehicle to
ground level.
37.
Replace upper and lower rear
quarter panel trim. Replace plastic
hooks. Secure child seat restraint
anchors.
38.
Replace in the following order, floor
level trim, rubber rear tailgate
weather seal, spare wheel and
secure using spare wheel retainer,
spare wheel foam insert, cargo tray
( securing at all four corners ), right
hand side luggage drawer and two
piece luggage floor.
FIN10018
04/11/09
ISSUE 1.3
Page 6 of 8
A
FIGURE 13
FITTING INSTRUCTIONS FOR
NISSAN T31 X TRAIL
TOWBAR WIRING HARNESS
FITTING INSTRUCTIONS: Continued..
39.
Test the operation of the trailer
socket using a trailer wiring tester or
a test light to ensure correct
operation.
A
FIGURE 14
FIGURE 15
NO.
FUNCTION
1
L/H INDICATOR
YELLOW
3
EARTH
WHITE
4
R/H INDICATOR
GREEN
6
STOP LIGHT
RED
7
TAIL LIGHT
BROWN
8
REVERSE PARK SENSOR
BLUE/BLACK
9
REVERSE PARK SENSOR
GREY
FIN10018
04/11/09
ISSUE 1.3
WIRE COLOUR
Page 7 of 8
FITTING INSTRUCTIONS FOR
NISSAN T31 X TRAIL
TOWBAR WIRING HARNESS
FITTING INSTRUCTIONS: Continued..
40.
The correct method to remove
the weather strip is to peel back
the luggage compartment side
trim, grip the weather strip/welt
at the base and pull back to
remove.
Refer ( Fig 16 )
FIGURE 16
FIN10018
04/11/09
ISSUE 1.3
Page 8 of 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising