BeansTalk Expanded Hot Spot WDS Repeater Access Point AP

BeansTalk Expanded Hot Spot WDS Repeater Access Point AP
BeansTalk Expanded Hot Spot WDS Repeater Access Point AP - Ubiquiti Wiki
Pagina 1 di 3
Log in / create account
Navigation
Main Page
Community portal
Current events
Recent changes
Random page
Help
Search the Wiki
Go
Search
BeansTalk Expanded Hot Spot WDS Repeater Access Point AP
Offer comments, ask questions and join the discussion on this topic in the Ubiquiti Support Forum: [[1]
(http://forum.ubnt.com/showthread.php?t=51900) ]
Create an expanded-area Wi-Fi Hotspot using M2 radios that is capable of supporting up to 50 (max) nearby, traditional Wi-Fi clients for each
Access Point in the cluster.
Configuring an Expanded Area Wi-Fi Hot Spot
Accessing the Radio:
1. Restore your radio to FACTORY DEFAULT values. This is critical, especially if you are troubleshooting a problem.
2. Connect the radio to your computer using an Ethernet cable. The Ethernet port is auto-sensing. You are not required to use a cross-over
cable.
3. Using a web browser, enter 192.168.1.20 as the "URL" to gain access to the radio's management console.
4. Enter "ubnt" as the administration account and "ubnt" as the password.
http://wiki.ubnt.com/BeansTalk_Expanded_Hot_Spot_WDS_Repeater_Access_Point... 28/03/2014
BeansTalk Expanded Hot Spot WDS Repeater Access Point AP - Ubiquiti Wiki
Pagina 2 di 3
Configure the radio labeled as IP = 192.168.1.2 above:
A. Choose the |Wireless| tab, and change only:
Wireless Mode: AP-Repeater
WDS Peers: AA:BB:CC:00:00:03 (Example only. Use the actual MAC address of the OTHER radio)
Channel Width: 20 MHz
Frequency: Choose one from the list. NOTE: "Channel 1" = 2412, "Channel 6" = 2437, "Channel 11" = 2462
Press [Change] button
B. Choose the |Network| tab, and change only:
IP Address: 192.168.1.2
Press [Change] Button
C. Choose |Ubiquiti Logo| tab
AirMax: [ ] enable (UN-check)
Press [Change] Button, Press [Apply] Button
DONE with this radio. Repeat 1-4 with the second radio, then continue below.
Configure the radio labeled as IP = 192.168.1.3 above:
D. Choose the |Wireless| tab, and change only:
Wireless Mode: AP-Repeater
WDS Peers: AA:BB:CC:00:00:02 (Example only. Use the actual MAC address of the OTHER radio)
Channel Width: 20 MHz
Frequency: Choose THE SAME frequency that you chose above.
Press [Change] button
E. Choose the |Network| tab, and change only:
IP Address: 192.168.1.3
Press [Change] Button
F. Choose |Ubiquiti Logo| tab
AirMax: [ ] enable (UN-check)
Press [Change] Button, Press [Apply] Button
DONE
If using a Cable/DSL Modem:
G. Reboot or power cycle the Cable/DSL modem off and on before using this link.
DONE
NOTES:
1 - Secure your installation - modify the default administration account
-) Select |System| tab > System Accounts
-) Administrative Username [change it from 'ubnt']
-) Hover over icon to the right, "Change Password" and change it
-) Press [Change] button, press [Apply] button
2 - Secure your Wi-Fi from unauthorized use (unless you intend to run an open AP / Hot Spot)
-) Select |Wireless| Tab > Wireless Security
-) Security > WEP (this is the ONLY encryption available in this mode)
-) Preshared Key: [enter something long, but memorable to you]
-) Press [Change] button. Press [Apply] button.
Varieties of this Configuration
http://wiki.ubnt.com/BeansTalk_Expanded_Hot_Spot_WDS_Repeater_Access_Point... 28/03/2014
BeansTalk Expanded Hot Spot WDS Repeater Access Point AP - Ubiquiti Wiki
Pagina 3 di 3
Five Access Points, One Layer of Repeating
http://wiki.ubnt.com/BeansTalk_Expanded_Hot_Spot_WDS_Repeater_Access_Point... 28/03/2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising