INSTRUCTION MANUAL GEBRAUCHSANWEISUNG

INSTRUCTION MANUAL GEBRAUCHSANWEISUNG
I
‘
DIGITAL $R~P~RTI~N~
RADIO CONTROL SYSTEM
INSTRUCTION MANUAL
DIGITAL PROPORTIONAL
RADIO CONTROL SYSTEM
GEBRAUCHSANWEISUNG
f
i
I
-
..___
-- -
Dear Radio Control Hobby Friend,
L
.
Congratulations on buying this ACOMS “TECHNIPLUS CX ” AP- 201 / 40 twochannel digital radio control set, which has been manufactured and assembled
with the greatest care.
We are confident that by following our simple instructions you will be
delighted with your purchase. Please read the instructions thoroughly, noting
all point before use, in order to avoid mistakes in handling and operation.
Should you carry out your own repairs or modifications to the apparatus
or to any part of, it, we cannot accept responsibility and the guarantee
becomes null and void.
It is advisable to check your ACOMS “TECHNIPLUS a ” AP - 201 / 40 before
installing it into your model.
If the set has been damaged through misuse, a charge will be made for
repair, the amount of which will be dependent on the damage.
We wish you a lot of pleasure with our ACOMS “TECHNIPLUS 0 “AP - 201 / 40.
TRANSMITTER
AP-201
AR-221
RECEIVER
AS-12 2
SERVO BEC SWITCH HARNESS
SERVO HORN A.B
/40 40MHz
140 40MHz
PCS. included.
2 PCS. each of HORN
A and B included.
2 PCS. included.
WIRESTRAPS
4 PCS. included.
SERVO CUSHION SERVO CUSHION SHOULD BE USED ON SERVOS
WHERE NECESSARY
Al’TENTION
* To obtain the best results from your new ACOMS set it is recommended that you
observe the following : When starting, switch on the transmitter before the receiver.
When finishing, switch off the receiver before the transmitter.
* A very strict check of all materials used and a continuous inspection using specially
developed sophisticated measuring devices at all stage of production, ensures the
compatibility of all ACOMS equipment.
1
TRANSMITTER ACOMS AP-201/40 40MHz
* Highly efficient design with attractive color plastic case. This transmitter gives a stable
and adequate output under most climatic conditions.
* The frequency bands are precise and conform to internationally recognized standards.
They are free from spurious radiation and therefore do not interfere with adjacent
bands. For your guidance the bands are displayed on the front of the case.
* The transmitter is equipped with a high grade LED indicator so that the voltage state
of batteries can be checked easily. If this LED Light indicates in Yellow / Red colors,
you may need to c ’ nge batteries.
$.
* Interchangeable plug - in crystals enable
a rapid change of frequency by simply
unplugging from the front of the case.
(IO interchangeable crystals in the 40 MHz
band.) The use of crystals, other than
ACOMS, can damage the radio and
invalidates our guarantee.
RECEIVER ACOMS AR-221 140 40MHz
* The basic efficiency of this receiver, namely multi -signal intensified input jamming ratio,
cross talk jamming ratio, practical sensitivity and stability, is highly efficient through
the adoption of special semi -conductors
and the ACOMS unique circuit system.
* Make sure the crystal is fully inserted in
the receiver and not partially inserted or
floating.
SERVO- ACOMS AS-12
* The sturdy (replaceable) gears have been designed to stand up to considerable shocks
and loads when used normally and are highly efficient.
* Since this servo is designed to be splashproof, its use in electric off - road cars is
recommended.
Channel:
Frequency MHz:
50
51
52
53
54
58
82
86
90
92
40.665 40.675 40.685 40.695 40.715 40.775 40.825 40.885 40.965 40.985
2
1) RETRACTABLE 7 SECTION AERIAL
Use fully extended except on short range or testing indoors.
2) BAITERY INDICATOR
If the LED Light indicates in Yellow /Red colors, the batteries are weak and may
need changing.
3) FUNCTION 1 STICK
4)
FUNCTION 1 TRIM TAB
This useful device enables you to trim the control and obtain true neutral, allowing for
various unforeseen variations in the performance characteristics of your model.
The ACOMS trim $bs are on a ratchet which means you are able to make a fine
adjustment and set ‘it.
5)
CHARGER CONNECTOR
Note : ON / OFF switch should be ‘OFF’ position before charging. A charger is to be
used only for Nickel-Cadmium batteries (Ni-Cd).
7) ON /OFF SWITCH
6) CRYSTAL
8) SERVO REVERSE SWITCHES
-c!iiti
Channel 1 and Channel 2 servos can be reversed from the transmitter separately with
these switches.
9)
NEUTRAL PRE - SET LEVER
You may change the ratio of slottle angle from normal 50 : 50 for forward / reverse to
70% forward and 30% reverse.
10) FUNCTION 2 STICK
11) FUNCTION 2 TRIM TAB
.
CONNECTIONS TO BEC RECEIVER
“Ni-Cd Battery and Speed Controller are not included in the Radio set.
Switch Harness
Transmitter AP-201 / 40
Antenna Output
Modulation System
impulse Tolerence
Length of Cycle
Power Supply Dry Cell
Receiver AR-221 / 40
(BEC System)
Servo AS-l 2
DC 6.0 - 8.4V
From receiver
500m W
AM
1.4mS + 0.4mS
18mS
DC 12V
( from Ni-cd battery
for car running )
455 KHz
Intermediate Frequency
5KHz/-6db
BAND Width
2.6 kg /cm or more
Torque
It is the policy of ACOMS to strive to improve their quality.
ACOMS therefore reserve their right to alter these specification at any time without notice.
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising