Prosound N43QR / N44QR www.maplin.co.uk

Prosound N43QR / N44QR www.maplin.co.uk
 I N S T R U C T I O N M A N U A L Prosound N43QR / N44QR UHF wireless microphone kit Due to continuous product development, please ensure that you have downloaded the latest instruction manual for this product from the Maplin website at www.maplin.co.uk For the latest updates and information on the entire Prosound range visit: www.maplin.co.uk Manufactured in China by Maplin Electronics S63 5DL, UK Due to continuous product development, specifications and appearance are subject to change. E&OE. Thank you for purchasing this product, we are sure that it will serve you for many years to come. To optimise the performance of this product, please read these operating instructions carefully to familiarise yourself with the basic operations of this unit. Please retain them for future reference. This product has been tested at the factory before being shipped to you. To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. To prevent a fire hazard, do not expose the unit to any naked flame sources. Unplug this apparatus during lightning storms or if it is unlikely to be used for long periods of time. When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings in the unit are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered. Always handle the power cable by the plug. Never pull out the plug by pulling on the cable. Never touch the power cable when your hands are wet as this could cause an electric shock. Do not tie a knot in the cable. The power cable should be placed such that it is not likely to be stepped on. A damaged power cable can cause a fire or give you an electrical shock. Check the power cord periodicaly, if you ever find that it is damaged, replace it before using the unit again. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit is to be used meets the unit’s requirement. The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the unit’s enclosure that may be of sufficient power to constitute a risk of electrical shock to you. The exclamation mark inside a triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance. Caution: to prevent the risk of electric shock, do not attempt to open the unit. No user-­‐serviceable parts inside. Refer all servicing to qualified service personnel. Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to vibration and excessive dust. Do not use the unit where there are extremes in temperature (below 41°F / 5°C or exceeding 95°F / 35°C). Unpacking and safety -­‐ please unpack your new product carefully. Your new product should reach you in perfect condition. Please check that no damage has occurred during transit. If any damage is found, do not operate your unit. Please contact the retailer you purchased it from immediately. If there is any damage to the mains cable do not use the device. Always disconnect the unit from the mains supply when carrying out any cleaning of the unit. Manufacturer declarations In compliance with the following requirements: RoHS Directive (2002/95/EU) and WEEE Directive (2002/96/EU). If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal. CE declaration of conformity R&TTE Directive (1999/5/EU), EMC Directive (2004/108/EU), Low Voltage Directive (2006/95/EU). Installation of the receiver Place the receiver higher than one meter from the floor. The receiver should be placed than one meter from any walls. The unit’s antenna should be fully extended. Ensure that there is a clear ‘line of sight’ between the receiver and the transmitter (mic or bodypack). Any obstruction between the two could result in a loss of signal to the receiver. Operation of the receiver Adjust the antenna on the rear of the unit so that it is perpendicular with the receiver. Turn the volume control fully down on the front of the receiver. Connect the receiver to the mains via the power adapter. Connect the audio output on the rear of the receiver to a mixer or amplifier. Turn the receiver on using the power switch on the front of the unit. The volume is controlled using the volume knob on the front of the unit. Operation of the transmitter (microphone or bodypack) Remove the battery cover from the transmitter and insert the battery ensuring that the polarity is correct (match plus to plus and minus to minus). If using the handheld microphone, turn it on using the On/Off switch. If you are using the bodypack transmitter, connect an input (lavalier/tie microphone or guitar or headset). Turn on the bodypack using the On/Off switch. Receiver specification Carrier frequency N43QR: UHF 863.8 MHz / N44QR: UHF 863.3 MHz Frequency stablisation Less than +/-­‐ 30ppm Dynamic range More than 90dB Total harmonic distortion Less than 0.8% Frequency response 40Hz – 15KHz +/-­‐3dB Audio output level Mixed: 0 – +/-­‐400mV / Separate: 0 – +/-­‐200mV Power supply DC12-­‐18V Power consumption 1w Signal to noise ratio More than 100dB Image & spurious rejection More than 80dB Border upon channel rejection More than 80dB Receiving sensitivity 5dBuV (SINAD>20dB) De-­‐emphasis 50us Handheld microphone Transmitter power 10mW Modulation type FM / F3F Maximum deviation +/-­‐25KHz Spurious emission More than 40dB (with carrier) Battery voltage/usage AA 1.5V / 5 hours approximately Bodypack Transmitter power 10mW Modulation type FM / F3F Maximum deviation +/-­‐25KHz Spurious emission More than 40dB (with carrier) Battery voltage/usage AA 1.5V x 2 / 5 hours approximately y
y
u
q
i
e qr
w
q
w
e
r
t
t
Controls and functions Receiver 1. Power switch 2. Volume control knob 3. Power supply indicator 4. Channel A signal indicator 5. Channel B signal indicator 6. Antenna 7. Audio output 8. DC input Bodypack transmitter (N44QR only) 1. Power switch 2. Power supply indicator 3. Audio input (lavalier/tie microphone or guitar or headset) 4. Volume control 5. Battery cover (not shown) 6. Adjustable gain 7. High / Low power switch 8. Battery sink Microphone transmitter (N43QR only) 1. Grille 2. Power supply indicator 3. Power switch 4. Battery cover (not shown) w
e
uy r
i
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising