M1BR3/M1R3/MM1P Compact Three Channel Mixer/Bi

M1BR3/M1R3/MM1P Compact Three Channel Mixer/Bi
M1BR3/M1R3/MM1P Compact Three
Channel Mixer/Bi-Amp Monitor
Speaker w/ Built-in
Rechargeable Battery*
Quick Start Guide
WHAT IS IN THE BOX
Your M1BR3/M1R3/MM1P package contains the following:
(1) Speaker
(1) Right Angle Speaker Cable
(1) 12V AC Power Supply Adaptor
(1) Quick Start Guide
(1) 12V DC Car Battery Supply Adapter
(1) Registration Card
*Rechargeable battery available in M1BR3 and M1R3 only
** Bluetooth® available in M1BR3 models only
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Ing. and any use of such marks
by Elite Acoustics Designs, Inc is under license
NOTE: Due to continuous development and improvements of our products, features and specifications are subject to
change without notice. All weights and measures are approximate.
QUICK START
1. Make sure the SPEAKER VOLUME [8] control is down before you turn the
POWER [14] on.
2. Connect the output of your microphone to the MIC IN [1]. Or you can connect a
¼” line input from an instrument [2]. Connect an additional mono or stereo [4]. A
direct USB connection can be made via the USB port [16].
3. Connect the DC power cord to the back panel [14].
4. Turn on the POWER [14] switch
5. **For M1BR3 only, Connect device to Bluetooth
6. Turn on your signal(s) and adjust the volume on the source signal for normal
operation. Note if you are using an iPhone or iPad via Bluetooth, set the volume on
your device about halfway. Maximum volume will distort.
7. Adjust the SPEAKER VOLUME [8] to a comfortable level.
8. Turn up GAIN [3] and TRIM [5] until there is a solid green light showing “signal” at
desired level, without a red “peak” light, indicating too much signal.
9. For USB charging of your source device, use USB Port [15]
Power LED: BLUE [9] Indicate unit is ON
Channel 1 [12]
Pan: split signal into Left/Right channel
Level: Volume Control
Peak LED: RED indicate Signal Clip
Signal LED: GREEN indicate Signal Present
Speaker
Speaker Volume [8]: Control speakers' volume level
Equalizer [10]: Adjust Speaker High, Mid, and Low Frequency response
Peak LED [9]: RED indicate Signal Clip
Signal LED [9]: GREEN indicate Signal Present
Aux Input/Level [11]: Connect audio source with 1/8" jack from MP3/CD player
Channel 1 input:
Gain [3] knob: Input Level control
Line In [2]: 1/4" TRS inputs
Mic In [1]: XLR for Microphone Input
Channel 2/3 input:
Trim Knob [5]: Input Level control
Left/Right channel input [4]: 1/4" TRS input
Main Right to SPK switch [6]: Right channel signal. When the button is up, only the
Right channel mono signal is sent for connection to the L (mono) of additional speaker.
Main Right Output [6]: Connect with extra speakers/monitors
BLUETOOTH® FUNCTION
• To turn ON/OFF Bluetooth® function
PRESS/HOLD down MODE button for approximately 5 seconds
Both LEDs will flash at the same time
• To pair device to the speaker system
Bluetooth® needs to be turned ON
QUICK TAP the MODE button once
Both Flashing LED: indicate Bluetooth ® is ready to be paired
Flashing Blue LED only: indicate Bluetooth® is connected
15
3
2
1
5
4
6
8
7
11
14
13
1.
2.
3.
4.
9
10
12
16
TO FULLY CHARGE SPEAKER SYSTEM
Put power switch in the “OFF” position
Plug in power adaptor into the DC input jack
Blue “Charge” LED will turn on, indicating the speaker is charging
When the speaker is fully charged, the blue “Charge” LED will turn off
•
•
•
•
•
•
•
FOR MAXIMUM BATTERY LIFE
Recharge after every use
Use & recharge battery at least once a month
DO NOT leave power switch in the “ON” position when it is not
in use. Doing so after a long period of time will damage the
battery
Keep unit in a cool, dry place away from extreme
temperatures
Do not service, modify, or replace the battery
If the battery fails to charge, contact Elite Acoustics Designs
WARRANTY
Elite Acoustics Designs Inc. warrants this product to be free of defects in material and workmanship for a period of
90 days from the date of original retail purchase. This warranty is enforceable only by the original retail purchaser.
To be protected by this warranty, the purchaser must complete and return the enclosed warranty card within 14
days of purchase. During the warranty period EAD/Sunburst Gear shall, as its sole and absolute option, either
repair or replace, free of charge, any product that proves to be defective on inspection by EAD/Sunburst Gear
or its authorized service representative. To obtain warranty service, contact Sunburst Gear Technical Support
via email: RMA@sunburstgear.com. PRE-AUTHORIZATION MUST BE OBTAINED BEFORE SENDING ANY
PRODUCT TO A SUNBURST GEAR SERVICE CENTER. All inquires must be accompanied by a description
of the problem. All authorized returns must be sent to the EAD/Sunburst Gear repair facility postage prepaid,
insured and properly packaged. EAD/Sunburst Gear reserves the right to update any unit returned for repair.
EAD/Sunburst Gear reserves the right to change or improve the design of the product at any time without prior
notice. This warranty does not cover claims for damage due to abuse, neglect, alteration, or attempted repair
by unauthorized personnel and is limited to failures arising during normal use that are due to defects in material
or workmanship in the product. Any implied warranties, including implied warranties of merchantability and
fitness for a particular purpose, are limited in duration to the length of this limited warranty. Some states do
not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In
no event will EAD Sunburst Gear be liable for incidental, consequential, or other damages resulting from the
breach of any express or implied warranty, including among other things, damage to property, damage based
on inconvenience or on loss of use of the product, and, to the extent permitted by law, damages for personal
injury. Some states do not allow the exclusion of limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary from state to state. This warranty only applies to products sold and used in the
United States of America. For warranty information in all other countries please refer to your local distributor.
©Elite Acoustics Designs Inc.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Speakers: 4” Woofer, one 1” Tweeter
Amplifier: Class D Bi-AMP
Nominal Input Level (1 kHz): CH1: -60 dBu, CH2/3: -20 dBu, AUX in: -10 dBu
Nominal output level (1 kHz): Right Channel Link out: -10 dBu
Channel controls: CH1: pan knob, level knob, CH2/3: level knob
Master controls: Volume knob, Equalizer (Low freq knob, Mid freq knob, High freq knob)
Aux in control: Level knob
Indicators: CH1: signal clip, Master: signal clip, power
Connectors: CH1: input jacks (XLR type, 1/4” TRS phone type), CH2/3: input jack Left/mono
(1/4” TRS phone type), input jack Right (1/4” TRS phone type), AUX in: input jacks (stereo
miniature phone type), Right channel output: line out jack Right (1/4” TRS phone type), DC in
jack
Power Switch
Power Supply: AC/DC 12V
*Built-in rechargeable Shielded Lead-Acid battery with battery meter: over 6 hours of
play time when battery is fully charge
o NOTE: Battery can also be charged with the 12V DC Car Battery Supply Adapter, which is included with the speaker, whether the switch is turned ON or OFF
Current Draw: 2000 mA
Other features:
o Optimized front ports for extended low-frequency response
o Magnetic shielding eliminates interference with other electronic equipment
o Built-in pole-mount, 35mm receptacle on bottom of unit
o **Playback from Bluetooth® device
Dimensions: 8.75”L x 7.25”W x 11 .5”H
For a copy of the complete User’s Manual, please visit: www.sunburstgear.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising