BEGA 7702LED
BEGA
Small scale floodlight with mounting canopy
Installation and Technical Information
7702LED
Tools Required:
Dimensions
3mm hex key
5mm hex key
Flat head screw driver medium
Phillips head screw driver medium
A:
6-1/4 ”
B:
8-7/8 ”
C:
6-1/2 ”
D:
3-7/8 ”
Protection Class: IP65
Weight: 5.07 lbs.
Notice to Installer for 7702LED:
1. See page 2 for specific product safety warnings.
2. Integral LED driver supplied by BEGA.
3. Luminaire mounts directly to standard recessed 4” octagonal wiring (by
others), using mounting plate provided.
4. Do NOT remove moisture absorption packet from luminaire housing.
7702LED - installation:
1. Loosen the (1) 3mm hex screw on the luminaire canopy and remove
luminaire base from luminaire.
2. Feed luminaire wiring through the luminaire base and mounting plate.
3. Make supply wiring and luminaire wiring connections inside the wiring box (by others):
MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE
GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE
Dimming (if applicable):
DIMMING CONTROL WIRE (+) TO POSITIVE DRIVER DIM CONTROL WIRE
DIMMING CONTROL WIRE (-) TO NEGATIVE DRIVER DIM CONTROL WIRE
4. Attach provided mounting plate directly to a 4” standard octagonal wiring box
using the (2) screws (provided). Place a small bead of silicone around the back side of the mounting plate that will come in contact with the finished surface (exterior applications only).
5. Align and position mounting plate on mounting surface to correspond with specified mounting orientation.
6. Slip luminaire base over the mounting plate. Tighten nuts on the studs (provided) to secure.
7. Replace luminaire canopy (with luminaire attached) and tighten (1) set screw.
8. To adjust head angle, use 5mm hex key to loosen adjustment screw. Adjust
luminaire head as needed and tighten adjustment screw.
Relamping/Maintenance
Remove trim and lens by loosening screws. Clean
luminaire and lens using only solvent-free cleansers.
Replace trim and lens. Tighten screws.
Lamp: 30W LED Module
Figure 1
Figure 2
Accessories
Please refer to the appropriate
accessory installation sheet for
further instruction when applicable.
Floodlight shield
757
Louver796
Flatbeam lens
060
Replacement Parts
Description
Part No
Lens
Lens gasket
LED driver (120-277V)
140852
831280
75916
LED Module 3000K
LED Module 4000K
LED-0175/830
LED-0175/840
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2014
7702LED
8/22/2014
Page 1 of 2
BEGA
Installation and Technical Information
Small scale floodlight with mounting canopy
7702LED
Product Safety Warnings:
CAUTION - RISK OF FIRE. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED. SUITABLE FOR WET LOCATIONS.
MIN 90°C SUPPLY CONDUCTORS.
ATTENTION - RISQUE D’INCENDIE. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES
INHÉRENTS. CONVIENT AUX EMPLACEMENTS MOUILLÉS.
LES FILS D’ALIMENTATION 90°C MIN.
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2014
7702LED
8/22/2014
Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising