ATV Computer ACE-31xx/37xx/38xx series User`s Manual

ATV Computer ACE-31xx/37xx/38xx series User`s Manual
PARTS
ATV Computer
ACE-31xx/37xx/38xx series User's Manual
www.acewell-meter.com
Main Unit Mounting
Max8mm
1.
Max8mm
sensor
2.
3.
7.
4.
PANEL DESCRIPTIONS
1. Tachometer Scale
2. Bar Tachometer
3. 1st row display: Current,
AVG and MAX speeds.
4. 2nd row display: Other functions display
Left direction indicator/Green
Main-beam headlamp/Blue
Right direction indicator/Green
Hazard Warning/ Red
Parking/Green
Direction indicator/Green
Flash Trailer/Green
N
R
D
8. LED Indicator symbols
Engine oil / Red
Neutral Gear /Green
Reverse Gear /Red
Drive Gear /Green
Engine coolant temperature/ Red
Rear fog lamp/Amber
Diesel engine ignition/
SPECIFICATIONS
INCREMENTS ACCURACY
500 rpm
100-19,900rpm
100 rpm
100-19,900rpm
100-19,900rpm
100 rpm
100 rpm
Speed Meter
2.3-300.0KM/h (187.5M/h)
0.1 KM/H or MPH +/- 0.1(KPH/MPH)
Maximum Speed Meter MAX
Average Speed Meter AVG
MAX 2.3-300.0KM/h (187.5M/h)
0.1 KM/H or MPH +/- 0.1(KPH/MPH)
AVG 2.3-300.0KM/h (187.5M/h)
+/-1% or
MPH +/- 0.1(KPH/MPH)
Shift Warning
Maximum Tachometer
Trip Meter
Odometer
Riding Time
Total Time
Clock
MAX
RPM
TRIP
ODO
RT
TT
RPM Sensor Mounting
RPM-INPUT
Either One
3-5 Turns
7. Fuel Meter Bar (Option)
500-11,000 rpm
RPM
RPM
Spring washer
6. MODE Button
SPECIFICATIONS
Digital Tachometer
Washer
5. RESET Button
Includes analogue and digital tachometer, 300km/h speedometer,
trip meter, odometer, clock, average speedometer, maximum
speedometer, riding timer and total riding timer.
Computer unit built in 4-8 LEDs for different purpose indicators.
LCD has 2 rows digital and an analogue bar-graphic tachometer
displays with blue LEDs backlight.
Odometer and total riding timer are stored in memory, even when
the power is off.
The computer always displays clock even when other functions are
power off.
Adjustable wheel circumference suitable for all kind of wheels: 13999mm setting range.
Metric/ British system option available.
Waterproof design
FUNCTIONS Symbol
Rubber pad
Attention:
1.Align the center of the magnet to
either of the sensor marking line
or the end of the sensor.
2.Installs the sensor parallel with
the vibration direction can get a
better anti-vibration effect.
3.Make sure the gap between the magnet
and the sensor is within 8mm.
Fixing screw nut
FEATURES
Bar Tachometer
Vibration Direction
Speed Sensor & Magnet Mounting
6.
Thanks for bought the Acewell's ATV/Scooter computer; this manual
is designed for ACE-3XXX series. ACE-3100/3150 does not have any
extra LED indicator. ACE-37XX/38XX series has 4-8 LED indicators.
Different model has different LED indicators, a fuel meter is
optional, and other functions are the same. You may found above
photo has different LED indicators from your computer; the photo
above is for reference only.
P
Vibration Direction
8.
5.
sensor
+/-1% or
+/-1% or
0.1 KM/H or
0.00-9999.99 Km (6249.99 Miles) 0.01 Km or Miles
+/- 0.1%
0.0 - 99999.9 Km (0.0- 62499.9 Miles) 0.01 Km or Miles
+/- 0.1%
0:00'00"- 99:59'59"
1 Second
+/- 50PPM
9999H59'
0:00'00"- 24:59'59"
1 Minute
+/- 50PPM
1 Second
+/- 50PPM
Power Input: 12VDC.
Speed Sensor: No Contact Magnetic Sensor.
Tachometer Input: CDI or Ignition coil signal.
Wheel Circumference setting: 1mm - 3999 mm (1 mm increment)
Operation Temperature: -10°C - +80°C (inner housing)
Storage Temperature:
-25°C - +85°C (Inner housing)
CDI
Ignition Coil
FUNCTIONS
BAR RPM: Bar Graphic Tachometer
1. The bar graphic tachometer is always displayed at the bar graph.
2. It displays bar graphic tachometer up to 12,000RPM.
RPM: Digital Tachometer
1. RPM is displayed at 2nd row.
2. It displays digital tachometer up to 19,900RPM.
3. Tachometer signal can pick up from either CDI or Ignition coil.
Shift Warning RPM
1. The function enables you to set up a shift warning RPM.
2. Bar-graphic tachometer flashes when RPM reaches setting value, and stop flash after
you shift gear.
MAX RPM: Maximum Tachometer
1. MAX RPM is displayed at the 2nd row.
2. Displays highest tachometer achieved after last Reset operation.
SPD: Speed Meter
1. Speed meter display is at the 1st row of the screen
2. Displays speed meter up to 300.0 Km/H or 187.5 mph.
MAX: Maximum Speed Meter
1. MAX is displayed at the 1st row.
2. Displays highest speed achieved after last Reset operation.
AVG: Average Speed Meter
1. AVG is displayed at the 1st row.
2. It calculates average speed from last RESET.
TRIP: Trip Meter
1. TRIP function accumulates trip distance from last RESET as long as ATV is being
ridden.
2. Display is on the 2nd row of screen.
ODO: Odometer
1. ODO accumulates total accumulated distance traveled during ATV operation.
2. ODO data is stored in memory, even when the power is off.
RT: Riding Timer
1. Calculates total operation time from last RESET.
2. Count automatically begins with movement.
TT: Total Riding Timer
1. Calculates total operation time from the beginning of the ATV.
2. Count automatically begins with movement.
3. TT data is stored in memory, even when the power is off.
12/24 hour Clock
It displays 12 or 24hour current time.
Fuel Meter (Only for models with the function)
Have 7 bars to indicate how much fuel remains. Last bar flashes to indicate low fuel
level.
BUTTON OPERATIONS
MODE BUTTON
1. Press the MODE button to move all functions in loop sequence from one function screen to another when the speed sensor does not detect
any signal input.
MODE
MODE
MODE
MODE
MODE
MODE
MODE
2. Press the MODE button to move partial functions in loop from one function screen to another when speed sensor detects signal input.
MODE
MODE
MODE
MODE
3. LCD screen will automatically revert to Speed Meter and Trip Meter screen during operation movement, if no button usage for 10 seconds.
RESET BUTTON
1. Press MODE button to the desired screen then press RESET button for
2 seconds to reset TRIP, RT, MAX, AVG and MAX RPM data from stored
values to zero individually.
2. ODO and TT data cannot be reset.
RESET
2 sec
SHIFT WARNING RPM OPERATION
1. Press MODE button to the RPM screen; pull on the throttle until the desired shift warning RPM displayed.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tachometer and a LED will flash to warning you shift gear.
4. Operate items 1 & 2 to re-adjust the shift warning RPM.
WHEEL CIRCUMFERENCE TABLE
1. The following table is calculated by the formula of Tire Diameter (inch) x 25.4(mm/inch) x 3.1416 = wheel circumference (in mm).
2. Identify the tire size of your ATV when you need to change different tire size and key in the corresponding number shown in the following chart.
Tire Size
15 inch
Circumference
number (mm)
1197mm
Tire Size
19 inch
Circumference
number (mm)
1516mm
Tire Size
23 inch
Circumference
number (mm)
1835mm
16 inch
1277mm
20 inch
1596mm
24 inch
1915mm
17 inch
1357mm
21 inch
1676mm
25 inch
1995mm
18 inch
1436mm
22 inch
1756mm
26 inch
2075mm
UNIT & WHEEL CIRCUMFERENCE SETTING
1. Setup operations include 12/24hour clock, shift warning RPM, numbers of engine rotation per signal, wheel circumference and units. You have to
set up step by step. The computer will automatic reversion to main screen if no button operation for 20 seconds at any setting screen.
2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert
units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at
any setting screen to finish the setting and go to main screen.
3. It displays "12 or 24H and XX:XX-XX" symbols and AM/PM in case you select 12H.
4. Press RESET button converts 12/24H, press MODE button to complete the setting and jump to clock digit setting.
5. Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next digit.
6. Press MODE button to go to shift warning RPM setting screen after set clock.
7. It displays "rXXX00 RPM". Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next
digit.
8. Press MODE button to go to numbers of engine rotation per signal setting screen after completed shift warning RPM setting.
9. It displays "SPC-X.X RPM", the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal.
For example the value 2.0 means the engine rotate 2 turns to output a signal.
10. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to
wheel circumference setting screen.
11. In "cXXXX" display, "c" means "Circumference", following 4 default digits; flashing digit is digit to be set.
12. Press RESET button to increase flashing digit by one; press MODE button for 2 seconds to confirm digit setting and jump to main screen.
mode
+
reset
2 sec
mode
mode
mode
2sec
mode
mode
mode
mode
mode
reset
mode
mode
reset
mode
mode
mode
mode
mode
mode
PARTS
ATV Computer
ACE-31xx/37xx/38xx series User's Manual
www.acewell-meter.com
Main Unit Mounting
Max8mm
1.
Max8mm
sensor
2.
3.
7.
4.
PANEL DESCRIPTIONS
1. Tachometer Scale
2. Bar Tachometer
3. 1st row display: Current,
AVG and MAX speeds.
4. 2nd row display: Other functions display
Left direction indicator/Green
Main-beam headlamp/Blue
Right direction indicator/Green
Hazard Warning/ Red
Parking/Green
Direction indicator/Green
Flash Trailer/Green
N
R
D
Vibration Direction
Speed Sensor & Magnet Mounting
6.
Thanks for bought the Acewell's ATV/Scooter computer; this manual
is designed for ACE-3XXX series. ACE-3100/3150 does not have any
extra LED indicator. ACE-37XX/38XX series has 4-8 LED indicators.
Different model has different LED indicators, a fuel meter is
optional, and other functions are the same. You may found above
photo has different LED indicators from your computer; the photo
above is for reference only.
P
Vibration Direction
8.
5.
sensor
Rubber pad
Attention:
1.Align the center of the magnet to
either of the sensor marking line
or the end of the sensor.
2.Installs the sensor parallel with
the vibration direction can get a
better anti-vibration effect.
3.Make sure the gap between the magnet
and the sensor is within 8mm.
Washer
Spring washer
RPM Sensor Mounting
RPM-INPUT
Either One
Fixing screw nut
5. RESET Button
6. MODE Button
2-5 Turns
7. Fuel Meter Bar (Option)
8. LED Indicator symbols
Engine oil / Red
Neutral Gear /Green
Reverse Gear /Red
Drive Gear /Green
Engine coolant temperature/ Red
Rear fog lamp/Amber
Engine in "out of use"/Red
FEATURES
CDI
Ignition Coil
1. The signal intensity from ignition coil is dependent on different bikes.
2. Circles 2-5 turns around ignition coil, the weaker signal the more
turns and the stronger signal the less turns you have to circle.
FUNCTIONS
BAR RPM: Bar Graphic Tachometer
1. The bar graphic tachometer is always displayed at the bar graph.
2. It displays bar graphic tachometer up to 12,000RPM.
Includes analogue and digital tachometer, 300km/h speedometer,
RPM: Digital Tachometer
trip meter, odometer, clock, average speedometer, maximum
1. RPM is displayed at 2nd row.
speedometer, riding timer and total riding timer.
2. It displays digital tachometer up to 19,900RPM.
Computer unit built in 4-8 LEDs for different purpose indicators.
3. Tachometer signal can pick up from either CDI or Ignition coil.
LCD has 2 rows digital and an analogue bar-graphic tachometer
Shift Warning RPM
displays with blue LEDs backlight.
1. The function enables you to set up a shift warning RPM.
Odometer and total riding timer are stored in memory, even when
2. Bar-graphic tachometer flashes when RPM reaches setting value, and stop flash after
the power is off.
you shift gear.
The computer always displays clock even when other functions are
MAX RPM: Maximum Tachometer
power off.
1. MAX RPM is displayed at the 2nd row.
Adjustable wheel circumference suitable for all kind of wheels: 12. Displays highest tachometer achieved after last Reset operation.
3999mm setting range.
SPD: Speed Meter
Metric/ British system option available.
1. Speed meter display is at the 1st row of the screen
Waterproof design
2. Displays speed meter up to 300.0 Km/H or 187.5 mph.
MAX: Maximum Speed Meter
SPECIFICATIONS
1. MAX is displayed at the 1st row.
2. Displays highest speed achieved after last Reset operation.
FUNCTIONS Symbol SPECIFICATIONS
INCREMENTS ACCURACY
AVG: Average Speed Meter
Bar Tachometer
500-11,000 rpm
500 rpm
1. AVG is displayed at the 1st row.
Digital Tachometer RPM 100-19,900rpm
100 rpm
2. It calculates average speed from last RESET.
TRIP: Trip Meter
100 rpm
Shift Warning
RPM 100-19,900rpm
1. TRIP function accumulates trip distance from last RESET as long as ATV is being
MAX
100
rpm
Maximum Tachometer RPM 100-19,900rpm
ridden.
+/-1% or
Speed Meter
0.1 KM/H or MPH +/- 0.1(KPH/MPH)
2.3-300.0KM/h (187.5M/h)
2. Display is on the 2nd row of screen.
+/-1% or
Maximum Speed Meter MAX MAX 2.3-300.0KM/h (187.5M/h) 0.1 KM/H or MPH +/- 0.1(KPH/MPH)
ODO: Odometer
+/-1% or
1. ODO accumulates total accumulated distance traveled during ATV operation.
Average Speed Meter AVG AVG 2.3-300.0KM/h (187.5M/h) 0.1 KM/H or MPH +/- 0.1(KPH/MPH)
2. ODO data is stored in memory, even when the power is off.
Trip Meter
TRIP 0.00-9999.99 Km (6249.99 Miles) 0.01 Km or Miles +/- 0.1%
RT: Riding Timer
Odometer
ODO 0.0 - 99999.9 Km (0.0- 62499.9 Miles) 0.01 Km or Miles +/- 0.1%
1. Calculates total operation time from last RESET.
+/- 50PPM
Riding Time
1 Second
0:00'00"- 99:59'59"
RT
2. Count automatically begins with movement.
+/- 50PPM
TT: Total Riding Timer
Total Time
1 Minute
9999H59'
TT
1. Calculates total operation time from the beginning of the ATV.
Clock
+/- 50PPM
0:00'00"- 24:59'59"
1 Second
2. Count automatically begins with movement.
Power Input: 12VDC.
3. TT data is stored in memory, even when the power is off.
Speed Sensor: No Contact Magnetic Sensor.
12/24 hour Clock
Tachometer Input: CDI or Ignition coil signal.
It displays 12 or 24hour current time.
Wheel Circumference setting: 1mm - 3999 mm (1 mm increment)
Fuel Meter (Only for models with the function)
Operation Temperature: -10°C - +80°C (inner housing)
Have 7 bars to indicate how much fuel remains. Last bar flashes to indicate low fuel
Storage Temperature:
-25°C - +85°C (Inner housing)
Fuel Sensor Resistance: 100Ω(For models with fuel meter only) level.
BUTTON OPERATIONS
MODE BUTTON
1. Press the MODE button to move all functions in loop sequence from one function screen to another when the speed sensor does not detect
any signal input.
MODE
MODE
MODE
MODE
MODE
MODE
MODE
2. Press the MODE button to move partial functions in loop from one function screen to another when speed sensor detects signal input.
MODE
MODE
MODE
MODE
RESET BUTTON
1. Press MODE button to the desired screen then press RESET button for
2 seconds to reset TRIP 2, MAX, and MAX RPM data from stored
values to zero individually. The data of Trip 1, AVG & RT be reset
at the same time. ODO, clock and TT data cannot be reset.
RESET
2 sec
SHIFT WARNING RPM OPERATION
1. Press MODE button to the RPM screen; pull on the throttle until the desired shift warning RPM displayed.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tachometer and a LED will flash to warning you shift gear.
4. Operate items 1 & 2 to re-adjust the shift warning RPM.
WHEEL CIRCUMFERENCE TABLE
1. The following table is calculated by the formula of Tire Diameter (inch) x 25.4(mm/inch) x 3.1416 = wheel circumference (in mm).
2. Identify the tire size of your ATV when you need to change different tire size and key in the corresponding number shown in the following chart.
Tire Size
15 inch
Circumference
number (mm)
1197mm
Tire Size
19 inch
Circumference
number (mm)
1516mm
Tire Size
23 inch
Circumference
number (mm)
1835mm
16 inch
1277mm
20 inch
1596mm
24 inch
1915mm
17 inch
1357mm
21 inch
1676mm
25 inch
1995mm
18 inch
1436mm
22 inch
1756mm
26 inch
2075mm
UNIT & WHEEL CIRCUMFERENCE SETTING
1. Setup operations include 12/24hour clock, shift warning RPM, numbers of engine rotation per signal, wheel circumference and units. You have to
set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen.
2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert
units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at
any setting screen to finish the setting and go to main screen.
3. It displays "12 or 24H and XX:XX-XX" symbols and AM/PM in case you select 12H.
4. Press RESET button converts 12/24H, press MODE button to complete the setting and jump to clock digit setting.
5. Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next digit.
6. Press MODE button to go to shift warning RPM setting screen after set clock.
7. It displays " RPM rXXX00 ". Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next
digit.
8. Press MODE button to go to numbers of engine rotation per signal setting screen after completed shift warning RPM setting.
9. It displays "SPC-X.X RPM", the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal.
For example the value 2.0 means the engine rotate 2 turns to output a signal.
10. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to
wheel circumference setting screen.
11. In "cXXXX" display, "c" means "Circumference", following 4 default digits; flashing digit is digit to be set.
12. Press RESET button to increase flashing digit by one; press MODE button for 2 seconds to confirm digit setting and jump to main screen.
mode
+
reset
2 sec
mode
mode
mode
2sec
mode
mode
mode
mode
mode
reset
mode
mode
reset
mode
mode
mode
mode
mode
mode
ATV Computer
ACE-31xx/37xx/38xx series User's Manual
www.acewell-meter.com
INSTALLATION & PARTS
Main Unit Mounting
Max8mm
1.
Max8mm
sensor
2.
3.
7.
4.
PANEL DESCRIPTIONS
1. Tachometer Scale
2. Bar Tachometer
3. 1st row display: Speedometer
and MAX speedometer.
4. 2nd row display: Other functions
Left-Direction Indicator/Green
Main-Beam Headlamp/Blue
Right-Direction Indicator/Green
Hazard Warning/ Red
Parking/Green
Direction Indicator/Green
Trailer Flashers/Green
7. Fuel Meter Bar (Optional)
8. LED Indicator symbols
Engine coolant temperature/ Red
Rear Fog Lamp/Amber
Engine "Not In Use"/Red
SPECIFICATIONS
INCREMENTS ACCURACY
100 rpm
100-19,900rpm
100-19,900rpm
100 rpm
100 rpm
Speed Meter
2.3-300.0KM/h (187.5M/h)
0.1 KM/H or MPH +/- 0.1(KPH/MPH)
Maximum Speed Meter MAX
Average Speed Meter AVG
MAX 2.3-300.0KM/h (187.5M/h)
0.1 KM/H or MPH +/- 0.1(KPH/MPH)
AVG 2.3-300.0KM/h (187.5M/h)
+/-1% or
MPH +/- 0.1(KPH/MPH)
Shift Warning
Trip Meter 1&2
Odometer
Riding Time
Total Time
Clock
MAX
RPM
+/-1% or
+/-1% or
0.1 KM/H or
0.1 Km or Miles
+/- 0.1%
0.0 - 999999 Km (0.0- 624999 Miles)
1 Km or Miles
+/- 0.1%
0:00'00"- 99:59'59"
1 Second
+/- 50PPM
9999H59'
0:00'00"- 23:59'59"
1 Minute
+/- 50PPM
1 Second /1 Minute
+/- 50PPM
TRIP 1&2 0.0-999.9 Km (624.9 Miles)
ODO
RT
TT
Ignition Coil
1. Signal intensity from ignition coil is dependent on vehicle type.
2. Circles 2-5 turns around ignition coil, with more turns creating steadily
stronger signal, fewer turns creating weaker signal.
100-19,900rpm
Maximum Tachometer
CDI
Engine Oil / Red
N Neutral Gear /Green
R Reverse Gear /Red
D Drive Gear /Green
500 rpm
RPM
RPM
RPM-INPUT
Either One
2-5 Turns
500-11,000 rpm
Digital Tachometer
RPM Sensor Mounting
Spring Washer
6. MODE Button
SPECIFICATIONS
Symbol
Washer
Fixing Screw Nut
Includes analog and digital tachometer, speedometer(300km/h
maximum), trip meter, odometer, clock, average speedometer,
maximum speedometer, riding timer and cumulativel riding timer.
Computer unit has 4-8 built-in LED for different-purpose indicators.
LCD has 2 rows of digital and one analog bar-graphic tachometer
displays, with blue LED backlight.
Odometer and cumulative riding timer measurements are stored in
memory, even when power is off.
The computer's clock display is always on, even when other
functions are power-off.
Adjustable wheel circumference suitable for all kind of wheels:
setting range of 1-3999 mm setting.
Metric/ British system options.
Waterproof design
FUNCTION
Rubber Pad
Attention:
1.Align the center of the magnet to
either of the sensor marking line
or the end of the sensor.
2.Installing the sensor parallel to
the vibration direction creates
optimal anti-vibration effect.
3.Make sure the gap between the magnet
and the sensor is within 8mm.
5. RESET Button
FEATURES
Bar Tachometer
Vibration Direction
Speed Sensor & Magnet Mounting
6.
Thanks for purchsaing an Acewell ATV/Motorcycle/Scooter computer.
This manual is specifically designed for ACE-3XXX series. The
ACE-3100/3150 does not have any extra LED indicator. The ACE37XX/38XX series has 4-8 LED indicators. Different models have
different LED indicators; a fuel meter is optional, ut all other
functions are the same. You may find that the photo has a set of
LED indicators different from your computer; the photo is for
reference only.
P
Vibration Direction
8.
5.
sensor
Power Input: 12VDC.
Speed Sensor: No Contact Magnetic Sensor.
Tachometer Input: CDI or Ignition-coil signal.
Wheel Circumference setting: 1mm - 3999 mm (1 mm increment)
Operation Temperature: -10°C - +80°C (inner housing)
Storage Temperature:
-25°C - +85°C (Inner housing)
Fuel Sensor Resistance: 100Ω(For models with fuel meter only)
FUNCTIONS
BAR RPM: Bar Graphic Tachometer
1. The bar graphic tachometer reading is always displayed at the bar graph.
2. Tachometer bar graphic displays up to 12,000 RPM.
RPM: Digital Tachometer
1. RPM is displayed in 2nd row.
2. Digital tachometer displays up to 19,900 RPM.
3. Tachometer signal picked up from either CDI or Ignition coil.
Shift Warning RPM
1. Function enables you to set up an RPM shift warning.
2. Bar-graphic tachometer flashes when RPM reaches pre-set value, and stops flashing
after you shift gear.
MAX RPM: Maximum Tachometer
1. MAX RPM is displayed on 2nd row.
2. Displays highest tachometer reading achieved after last RESET operation.
SPD: Speed Meter
1. Speed meter display is on 1st row of the screen.
2. Displays speedometer reading up to 300.0 Km/H or 187.5 mph.
MAX: Maximum Speed Meter
1. MAX is displayed on 1st row.
2. Displays highest speed achieved after last RESET operation.
AVG: Average Speed Meter
1. AVG is displayed on 2nd row.
2. Calculates average speed from last RESET.
TRIP 1 & 2: Trip Meter 1& 2
1. TRIP function registers cumulative trip distance from last RESET while bike is being
ridden.
2. Display is on 2nd row of screen.
ODO: Odometer
1. ODO registers cumulative distance traveled during motorbike operation.
2. ODO data is stored in memory, even when power is off.
RT: Riding Timer
1. Calculates total operation time from last RESET.
2. Count automatically begins with vehicle movement.
TT: Total Riding Timer
1. Calculates total operation time from the beginning of bike use.
2. Count automatically begins with vehicle movement.
3. TT data is stored in memory, even when power is off.
12/24 hour Clock
It displays 12- or 24-hour current time.
Fuel Meter (Only for models with the function)
Has 7 bargraphic indicator of fuel status. Last bar flashes to indicate low fuel level.
BUTTON OPERATIONS
MODE BUTTON
1. Press the MODE button to move all functions in loop sequence from one function screen to another when the speed sensor does not detect
any signal input.
MODE
MODE
MODE
2. Press the MODE button to move partial functions in loop from one
function screen to another when speed sensor detects signal input.
MODE
MODE
MODE
MODE
MODE
MODE
RESET BUTTON
1. Press MODE button to the desired screen then press RESET button for
2 seconds to reset TRIP 2, MAX, and MAX RPM data from stored
values to zero individually.
2. The data of Trip 1, AVG & RT be reset at the same time when one of
the 3 data functions is being reset.
3. ODO, clock and TT data cannot be reset.
RESET
2 sec
SHIFT RPM WARNING OPERATION
1. Press MODE button to the RPM screen; pull on the throttle until the desired shift RPM warning displayed.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tachometer will flash to warning you shift gear.
4. Operate items 1 & 2 to readjust the shift warning RPM.
WHEEL CIRCUMFERENCE TABLE
1. The details below have been calculated using the following formula; Tire Diameter (inch) x 25.4(mm/inch) x 3.1416 = wheel circumference (in mm).
2. Identify the tire size of your ATV/Motorcycle when you need to change different tire, and key in the corresponding number shown in the following chart.
Tire Size
Circumference
Tire Size
Circumference
Tire Size
Circumference
15 inch
1197mm
19 inch
1516mm
23 inch
1835mm
16 inch
1277mm
20 inch
1596mm
24 inch
1915mm
17 inch
1357mm
21 inch
1676mm
25 inch
1995mm
18 inch
1436mm
22 inch
1756mm
26 inch
2075mm
UNIT & WHEEL CIRCUMFERENCE SETTING
1. Setup operations include 12/24hour clock, shift warning RPM, numbers of engine rotation per signal, wheel circumference and units. These must
be set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen.
2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert
units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at
any setting screen to finish the setting and go to main screen.
3. It displays "12 or 24H and XX:XX-XX" symbols and AM/PM in case you select 12H.
4. Press RESET button converts 12/24H, press MODE button to complete the setting and jump to clock digit setting.
5. Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next digit.
6. Press MODE button to go to shift warning RPM setting screen after set clock.
7. It displays " RPM rXXX00 ". Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next
digit.
8. Press MODE button to go to numbers of engine rotation per signal setting screen after completed shift warning RPM setting.
9. It displays "SPC-X.X RPM", the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal.
For example the value 2.0 means the engine rotate 2 turns to output a signal.
10. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to
wheel circumference setting screen.
11. In "cXXXX" display, "c" means "Circumference", following 4 default digits; flashing digit is digit to be set.
12. Press RESET button to increase flashing digit by one; press MODE button for 2 seconds to confirm digit setting and jump to main screen.
mode
+
reset
2 sec
mode
mode
mode
2sec
mode
mode
mode
mode
mode
reset
mode
mode
reset
mode
mode
mode
mode
mode
mode
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising