Speed Triple 1050 from VIN
English
Fitting Instructions:
Speed Triple 1050 from VIN 461332, Speed Triple R 1050,
Street Triple from VIN 480782 and Street Triple R from VIN 482182
A9708186, A9708262 and A9708269
Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's use of proven
engineering, exhaustive testing, and continuous striving for superior reliability, safety and performance.
Completely read all of these instructions before commencing the installation of the accessory kit in order to become
thoroughly familiar with the kit’s features and the installation process.
These instructions should be considered a permanent part of your accessory kit, and should remain with it even if your
accessory-equipped motorcycle is subsequently sold.
3
2
1
4
5
Parts Supplied:
1.
Flyscreen
1 off 4.
Screw, M5 x 14 mm
4 off
2.
Infill panel
1 off 5.
Cable tie
1 off
3.
Screw, M6 x 12 mm
3 off
Publication part number A9900509 issue 9, DC 71618
© Triumph Designs Ltd. 2015
1 of 5
Accessory Kit
Warning
Accessory Kit
This accessory kit is designed for use on Triumph
motorcycles listed in the accessory kit table on this page
and should not be fitted to any other manufacturer’s
motorcycle. Fitting this accessory kit to any other
manufacturer’s motorcycle will affect the performance,
stability and handling of the motorcycle. This may affect
the rider’s ability to control the motorcycle and could
cause an accident.
Model
VIN
Speed Triple
1050
From VIN 461332
From VIN 480782
A9708186
Street Triple
to
VIN 560476
From VIN 482182
Street Triple R
to
VIN 560476
Warning
Always have Triumph approved parts, accessories and
conversions fitted by a trained technician of an authorised
Triumph dealer. The fitment of parts, accessories and
conversions by a technician who is not of an authorised
Triumph dealer may affect the handling, stability or other
aspects of the motorcycle’s operation, which may result in
loss of motorcycle control and an accident.
A9708262
Speed Triple
1050
From VIN 461332
Speed Triple R
1050
All
From VIN 480782
Street Triple
to
VIN 560476
From VIN 482182
Warning
Street Triple R
Throughout this operation, ensure that the motorcycle is
stabilised and adequately supported to prevent risk of
injury from the motorcycle falling.
Warning
A torque wrench of known accurate calibration must be
used when fitting this accessory kit. Failure to tighten any
of the fasteners to the correct torque specification may
result in loss of motorcycle control and an accident.
2 of 5
to
VIN 560476
A9708269
Street Triple
From VIN 560477
Street Triple R
From VIN 560477
1.
5.
Position the motorcycle on a paddock stand.
Remove the cover and gasket attached to the rear of
the instruments. Retain the cover and gasket if the
motorcycle is to be returned to its original condition.
Speed Triple from VIN 461332 and
Speed Triple R only
2.
Release the three fixings and remove the front panel
from the fuel tank.
2
1
2
1
3
ccwj_1
2
1. Instruments cover
2. Bayonet fixings
3. Gasket
2
cgfo
1. Front panel
2. Fixings
6.
Disconnect the
instrument pack.
electrical
connector
from
the
7.
Release the screw and remove the instruments from
the bracket.
Street Triple and Street Triple R only
3.
Remove the seat.
4
All Models
4.
Disconnect the battery, negative (black) lead first.
Note:
•
The instruments cover is held in place by
bayonet type fixings. Gently pull on the cover to
release it.
1
cgpe
1.
2.
3.
4.
3 of 5
3
Electrical connector
Screw
Washer
Bayonet fixings
2
8.
Position the infill panel to the instruments bracket as
shown. Secure with the M6 x 12 mm screws from the
kit and tighten to 7 Nm.
Warning
When securing electrical cables with cable ties, ensure the
cable ties are fully tight. Ensure there is slack in the cables.
1
Failure to follow this warning may result in damage to the
electrical cables, which may lead to loss of motorcycle
control and an accident.
10. Secure the headlight harness to the instrument harness
with the cable tie provided.
cgpb
1. Screws
Note:
•
Ensure that the rubber boot on the electrical
connector is positioned over the instrument
socket and seals the connector.
9.
Fit the instruments to the infill panel and bracket
assembly. Tighten the screw to 3 Nm and connect the
electrical connector.
4
2
1
3
cgpa
1. Headlight harness
2. Instrument harness
3. Cable tie
11.
Secure the flyscreen to the infill panel with the
M5 x 14 mm screws from the kit. Tighten to 3 Nm.
1
3
2
1
3
cgpa
1.
2.
3.
4.
2
Electrical connector
Screw
Washer
Bayonet fixings
1
cgpc
1. Screws
2. Infill panel
3. Flyscreen
12. Reconnect the battery, positive (red) lead first.
4 of 5
Speed Triple from VIN 461332 and
Speed Triple R only
Warning
13. Refit the front panel to the fuel tank and tighten the
fixings to 3 Nm.
Street Triple and Street Triple R only
14. Refit the seat.
Warning
Move the handlebar to the left and right full lock while
checking that the mirrors do not restrict the steering by
contacting the flyscreen.
Operation of the motorcycle with restricted steering may
result in loss of motorcycle control and an accident.
Caution
Never ride an accessory-equipped motorcycle at speeds
above 80 mph (130 km/h). The presence of accessories
will cause changes in the stability and handling of the
motorcycle. Failure to allow for changes in motorcycle
stability may lead to loss of control or an accident.
Remember that the 80 mph (130 km/h) limit will be
reduced by the fitting of non-approved accessories,
incorrect loading, worn tyres, overall motorcycle condition
and poor road or weather conditions.
Warning
The motorcycle must not be operated above the legal
road speed limit except in closed-course conditions.
Warning
Move the handlebar to the left and right full lock while
checking that the mirrors do not contact the flyscreen
when moving the handlebar.
Damage to the flyscreen will result if the mirrors contact
the flyscreen. If the mirrors do make contact, adjust their
position.
15. If the mirrors contact the flyscreen when on full lock,
adjust the mirrors such that they will not contact it and
that they give rear visibility in the riding position.
16. Remove the motorcycle from the paddock stand.
Warning
After fitting the accessory kit the motorcycle will exhibit
new handling characteristics. Operate the motorcycle in a
safe area free from traffic to gain familiarity with any new
characteristics. Operation of the motorcycle when not
familiar with any new handling characteristics may result in
loss of motorcycle control and an accident.
Warning
If, after fitment of this accessory kit, you have any doubt
about the performance of any aspect of the motorcycle,
contact an authorised Triumph dealer and do not ride the
motorcycle until the authorised dealer has declared it fit
for use. Riding a motorcycle when there is any doubt as to
any aspect of the performance of the motorcycle may
result in loss of control of the motorcycle, leading to an
accident.
5 of 5
Only operate this Triumph motorcycle at high speed in
closed-course on road competition or on closed-course
race tracks. High speed operation should only be
attempted by riders who have been instructed in the
techniques necessary for high speed riding and are
familiar with the motorcycle’s characteristics in all
conditions. High speed operation in any other
circumstances is dangerous and will lead to loss of
motorcycle control and an accident.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising