Cerabar M PMC51, PMP51, PMP55
Technical Information
Cerabar M PMC51, PMP51, PMP55
Process pressure measurement
Pressure transmitter with ceramic and metal sensors; modular
design and easy operation;
With Analog or HART Electronics
Application
Your benefits
The Cerabar M pressure transmitter is used for the
following measuring tasks:
• Absolute pressure and gauge pressure measurement in
gases, steams or liquids in all areas of process
engineering and process measurement technology
• Level, volume or mass measurements in liquids
• High process temperature
– without diaphragm seals up to 125°C (257°F)
– with diaphragm seals up to 400°C (752°F)
• High pressure up to 400 bar (6000 psi)
• International usage thanks to a wide range of approvals
• Very good reproducibility and long-term stability
• High reference accuracy: up to 0.15%,
as PLATINUM version: 0.075%
• Turn down up to 20:1
• End-to-end modularity for differential pressure,
hydrostatics and pressure (Deltabar M – Deltapilot M –
Cerabar M), e.g.
– replaceable display
– universal electronics
• Easy commissioning without the need for an operating
tool
• Menu-guided operation onsite via 4 to 20 mA with
HART.
• Output signals: 4 to 20 mA, 4 to 20 mA with HART
TI436P/00/EN/10.09(b)
No. 71103453
Cerabar M PMC51, PMP51, PMP55
Table of contents
Function and system design. . . . . . . . . . . . . . . . . . . . . 4
Operating conditions (installation) . . . . . . . . . . . . . . 19
Device selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Level measurement (level, volume and mass) . . . . . . . . . . . . . . . . 6
Electrical differential pressure measurement with gauge pressure
sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Communication protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System integration (except analog electronics) . . . . . . . . . . . . . . . . 6
General installation instructions . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring arrangement for devices without diaphragm seal –
PMC51, PMP51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring arrangement for devices with diaphragm seal
– PMP55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal insulation – PMP55 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting with temperature isolator . . . . . . . . . . . . . . . . . . . . . .
Wall and pipe mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
"Separate housing" version . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oxygen applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Silicone-free applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ultrapure gas applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Applications with hydrogen . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Explanation of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Signal range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Load - 4...20 mA and 4...20 mA HART . . . . . . . . . . . . . . . . . . . . 10
Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dead time, time constant (T63) . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dynamic behavior: 4 to 20 mA (Analog electronics) . . . . . . . . . . 11
Dynamic behavior: current output (HART electronics) . . . . . . . . 11
Dynamic behavior: digital output (HART electronics) . . . . . . . . . 11
Damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cable entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Residual ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Influence of power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Performance characteristics – general . . . . . . . . . . . . 15
Reference operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Uncertainty of measurement for small absolute pressure ranges . . 15
Long-term stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Influence of orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Warm-up period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Performance characteristics – ceramic process isolating
diaphragm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Reference accuracy – PMC51 . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Total performance – PMC51 (digital output) . . . . . . . . . . . . . . . . 16
Total error - PMC51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Thermal change in the zero output and the output span –
PMC51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Performance characteristics – metal process isolating
diaphragm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Reference accuracy – PMP51, PMP55 without capillary . . . . . . . 17
Reference accuracy – PMP55 with capillary (digital output) . . . . . 17
Total performance – PMP51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Total error - PMP51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Thermal change in the zero output and the output span – PMP51 and
PMP55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2
19
19
19
19
20
20
21
22
22
22
22
Operating conditions (environment) . . . . . . . . . . . . . 23
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electromagnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . .
Overvoltage protection (optional) . . . . . . . . . . . . . . . . . . . . . . . .
23
23
23
23
24
24
24
Operating conditions (process) . . . . . . . . . . . . . . . . . 25
Process temperature limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Process temperature range, seals . . . . . . . . . . . . . . . . . . . . . . . . 25
Pressure specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Mechanical construction . . . . . . . . . . . . . . . . . . . . . . 27
F31 aluminum housing dimensions . . . . . . . . . . . . . . . . . . . . . .
F15 stainless steel housing dimensions . . . . . . . . . . . . . . . . . . . .
Process connections PMC51 (with ceramic process isolating
diaphragm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Process connections PMP51 (with metal process isolating
diaphragm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP55 basic device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Process connections PMP55 (with metal process isolating
diaphragm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
"Separate housing" version . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
27
27
33
38
39
54
55
55
Human interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Planning instructions for diaphragm seal systems . . . 61
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function and design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diaphragm seal filling oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Influence of the temperature on the zero point . . . . . . . . . . . . . .
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
61
62
62
66
67
Certificates and approvals . . . . . . . . . . . . . . . . . . . . . 68
CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Ex approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Pressure Equipment Directive (PED) . . . . . . . . . . . . . . . . . . . . . 68
Standards and guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . 69
PMC51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMC51 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMC51 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMC51 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMC51 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP51 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP51 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP51 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP51 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP55 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP55 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP55 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP55 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PMP55 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brief Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation/Control Drawings . . . . . . . . . . . . . . . . . . . . . . . . . .
85
85
85
85
86
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Shutoff valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siphon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welding necks and Weld-in tool flanges . . . . . . . . . . . . . . . . . . .
Mounting bracket for wall and pipe mounting . . . . . . . . . . . . . .
M12 connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87
87
88
89
89
Configuration data sheet (HART) . . . . . . . . . . . . . . . 90
Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
3
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Function and system design
Device selection
Cerabar M –
Product family
PMC51
PMP55
PMP51
P01-PMC51xxx-16-xx-xx-xx-000
With capacitive measuring cell and ceramic
process isolating diaphragm (Ceraphire®)
P01-PMP51xxx-16-xx-xx-xx-000
P01-PMP55xxx-16-xx-xx-xx-000
With piezoresistive measuring
cell and metal welded process
isolating diaphragm
With diaphragm seal
–
–
–
–
–
– Wide range of diaphragm seals
Field of application
– Gauge pressure and absolute pressure
– Level
Process connections
–
–
–
–
Measuring ranges
From –100/0 to 100 mbar (–1.5/0 to 1.5 psi)
to –1/0 to 40 bar (–15/0 to 600 psi)
From –400/0 to 400 mbar (–6/0 to 6 psi)
to –1/0 to 400 bar (–15/0 to 6000 psi)
OPL 1
Max. 60 bar (900 psi)
Max. 600 bar (9000 psi)
Process temperature range
–20 to +100 °C (–4 to +212°F)
–40 to +125°C (–40 to +257°F)
Ambient temperature range
• Without LCD display: -40 to +85°C (–40 to +185 °F)
• With LCD display: -20 to +70°C (–4 to +158°F) (extended temperature application range (-40 to 85°C (-40 to 185°F)) with
restrictions in optical properties such as display speed and contrast)
• Separate housing: –20 to +60°C (–40 to +140°F)
Reference accuracy
– Up to 0.15% of the set span
– PLATINUM version: up to 0.075% of the set span
Supply voltage
– 11.5 to 45 V DC (versions with plug-in connection 35 V DC)
– For intrinsically safe device versions: 11.5 to 30 V DC
Output
4 to 20 mA, 4 to 20 mA with superimposed HART protocol, (PROFIBUS PA and FOUNDATION Fieldbus under development)
Options
–
–
–
–
–
–
Specialties
– Process connections with
– Metal-free measurement with PVDF
minimum oil volume
connection
– Gas-tight, elastomer-free
– Special cleaning of the transmitter to remove
paint-wetting substances, for use in paint shops
1)
4
Threads
EN flanges DN 25 – DN 80
ANSI flanges 1" – 4"
JIS flanges 50 A – 100 A
Threads
EN flanges DN 25 – DN 80
ANSI flanges 1" – 4"
JIS flanges 25 A – 100 A
Prepared for diaphragm seal
mount
-70 to 400°C (-94 to +752°F)
Up to 0.15% of the set span
PMP51, PMP55: NACE-compliant materials
PMC51, PMP51, PMP55: inspection certificate 2.2 or 3.1 or other certificates
Specific firmware versions
Initial device settings
Separate housing
Broad range of accessories
– Wide range of diaphragm seals
– For extreme medium
temperatures
– Process connections with
minimum oil volume
– Completely welded versions
OPL = over pressure limit; depends on the lowest-rated element, with regard to pressure, of the selected components
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Measuring principle
Ceramic process isolating diaphragm used in PMC51 (Ceraphire®)
➀
➁
Metal process isolating diaphragm used in PMP51 and PMP55
➂
➀
➁
➃
➂
➃
p
p
P01-PMC71xxx-03-xx-xx-xx-000
P01-PMP7xxxx-03-xx-xx-xx-000
Ceramic sensor
Metal sensor
1
2
3
4
1
2
3
4
Air pressure (gauge pressure sensors)
Ceramic substrate
Electrodes
Ceramic process isolating diaphragm
Silicon measuring element, substrate
Wheatstone bridge
Channel with fill fluid
Metal process isolating diaphragm
Ceramic process isolating diaphragm used in PMC51 (Ceraphire®)
The ceramic sensor is a dry sensor, i.e. the process pressure acts directly on the robust ceramic process isolating
diaphragm and deflects it. A pressure-dependent change in capacitance is measured at the electrodes of the
ceramic substrate and the process isolating diaphragm. The measuring range is determined by the thickness of
the ceramic process isolating diaphragm.
Advantages:
• Guaranteed overload resistance up to 40 times the nominal pressure
• Thanks to ultrapure 99.9% ceramic (Ceraphire®, see also "www.endress.com/ceraphire")
– extremely high chemical stability, comparable with Alloy C
– less relaxation
– high mechanical stability
• Can be used in absolute vacuum
• Outstanding surface finish, Ra 0.3 m (11.8 in)
Metal process isolating diaphragm used in PMP51 and PMP55
PMP51
The operating pressure deflects the process isolating diaphragm and a fill fluid transfers the pressure to a
resistance bridge (semiconductor technology). The pressure-dependent change in the bridge output voltage is
measured and evaluated.
Advantages:
• Can be used for process pressure up to 400 bar (6000 psi)
• High long-term stability
• Guaranteed overload resistance up to 4 times the nominal pressure
• Significantly less thermal effect compared to diaphragm seal systems
PMP55
The operating pressure acts on the process isolating diaphragm of the diaphragm seal and is transferred to the
process isolating diaphragm of the sensor by a diaphragm seal fill fluid. The process isolating diaphragm is
deflected and a fill fluid transfers the pressure to a resistance bridge. The pressure-dependent change in the
bridge output voltage is measured and evaluated.
Advantages:
• Can be used for process pressure up to 400 bar (6000 psi) and simultaneous extrem process temperatures
• High long-term stability
• Guaranteed overload resistance up to 4 times the nominal pressure
Endress+Hauser
5
Cerabar M PMC51, PMP51, PMP55
Level measurement (level,
volume and mass)
Function and design
p
h= r g
h
P01-PMx5xxxx-15-xx-xx-xx-000
Level measurement
h
p
r
g
Height (level)
Pressure
Density of the medium
Gravitation constant
Your benefits
•
•
•
•
Choice of different level measuring modes in the device software
Volume and mass measurements in any tank shapes by means of a freely programmable characteristic curve
Choice of diverse level units
Has a wide range of uses, even in the following cases:
– in the event of foam formation
– in tanks with agitators or screen fittings
– in the event of liquid gases
Electrical differential pressure
measurement with gauge
pressure sensors
FXN 520
Cerabar M
➀
Fieldgate
FXA520
Multidrop-Connector
FXN520
➀
➁
P01-PMX51xxx-14-xx-xx-xx-001
1
Shut-off valves
2
e.g. filter
In the example given, two Cerabar M devices (each with a gauge pressure sensor) are interconnected. The
pressure difference can thus be measured using two independent Cerabar M devices.
"
Caution!
If using intrinsically safe devices, strict compliance with the rules for interconnecting intrinsically safe circuits
as stipulated in IEC60079-14 (proof of intrinsic safety) is mandatory.
Communication protocol
• 4 to 20 mA without communication protocol
• 4 to 20 mA with HART communication protocol
System integration (except
analog electronics)
The device can be fitted with a tag name and a preset bus address, see  ä 69 ff "Ordering information"
feature 895 "Identification:" version "Z1" and "Z2".
6
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Input
Measured variable
• Analog electronics: Absolute pressure and gauge pressure
• HART: Absolute pressure and gauge pressure, from which level (level, volume or mass) is derived
Measuring range
PMC51 – with ceramic process isolating diaphragm (Ceraphire®) for gauge pressure
Nominal value
Range limit
Smallest
calibratable span
MWP 1
OPL 2
Vacuum
resistance
4
Version in
the order
code 3
lower (LRL)
upper (URL)
[bar (psi)]
[bar (psi)]
[bar (psi)]
[bar (psi)]
[bar (psi)]
[barabs (psiabs)]
100 mbar (1.45 psi)
–0.1 (–1.5)
+0.1 (+1.5)
0.01 (0.15)
2.7 (40.5)
4 (60)
0.7 (10.5)
1C
250 mbar (4 psi)
–0.25 (–4)
+0.25 (+4)
0.01 (0.15)
3.3 (49.5)
5 (75)
0.5 (7.5)
1E
400 mbar (6 psi)
–0.4 (–6)
+0.4 (+6)
0.02 (0.30)
5.3 (79.5)
8 (120)
0
1F
1 bar (14.5 psi)
–1 (–15)
+1 (+15)
0.05 (1)
6.7 (100.5)
10 (150)
0
1H
2 bar (29 psi)
–1 (–15)
+2 (+30)
0.1 (1.5)
12 (180)
18 (270)
0
1K
4 bar (58 psi)
–1 (–15)
+4 (+60)
0.2 (3)
16.7 (250.5)
25 (375)
0
1M
10 bar (145 psi)
–1 (–15)
+10 (+150)
0.5 (7.5)
26.7 (400.5)
40 (600)
0
1P
40 bar (580 psi)
–1 (–15)
+40 (+600)
2 (30)
40 (600)
60 (900)
0
1S
PMC51 – with ceramic process isolating diaphragm (Ceraphire®) for absolute pressure
MWP 1
OPL 2
[barabs (psiabs)] [barabs (psiabs)] [bar (psi)]
[barabs (psiabs)]
[barabs (psiabs)] [barabs (psiabs)]
100 mbar (1.45 psi)
0
+0.1 (+1.5)
0.01 (0.15)
2.7 (40.5)
4 (60)
0
2C
250 mbar (4 psi)
0
+0.25 (+4)
0.01 (0.15)
3.3 (49.5)
5 (75)
0
2E
400 mbar (6 psi)
0
+0.4 (+6)
0.02 (0.30)
5.3 (79.5)
8 (120)
0
2F
1 bar (14.5 psi)
0
+1 (+15)
0.05 (1)
6.7 (100.5)
10 (150)
0
2H
2 bar (29 psi)
0
+2 (+30)
0.1 (1.5)
12 (180)
18 (270)
0
2K
4 bar (58 psi)
0
+4 (+60)
0.2 (3)
16.7 (250.5)
25 (375)
0
2M
10 bar (145 psi)
0
+10 (+150)
0.5 (75)
26.7 (400.5)
40 (600)
0
2P
40 bar (580 psi)
0
+40 (+600)
2 (30)
40 (600)
60 (900)
0
2S
Nominal value
Range limit
Smallest
calibratable span
Vacuum
resistance
4
lower (LRL)
1)
2)
3)
4)
Endress+Hauser
Version in
the order
code 3
upper (URL)
The MWP (maximum working pressure) for the measuring device depends on the lowest-rated element, with regard
to pressure, of the selected components, i.e. the process connection ( ä 27 ff) has to be taken into consideration
in addition to the measuring cell ( see Table above). Pay attention to the pressure-temperature dependence also.
For the appropriate standards and other information, see  ä 26, Pressure specifications section.
OPL: over pressure limit depends on the lowest-rated element, with regard to pressure, of the selected components
Version in the order code see also  ä 69 ff, feature 70 "Sensor range"
Turn down > 20:1 can be configured in the device or on request
7
Cerabar M PMC51, PMP51, PMP55
PMP51 and PMP55 – metal process isolating diaphragm for gauge pressure
Nominal value
Range limit
Smallest
calibratable
span 5
MWP 1
OPL 2
Vacuum
resistance 3
Version in the
order code 4
lower
(LRL)
upper
(URL)
Silicone oil/
Inert oil
[bar (psi)]
[bar (psi)]
[bar (psi)]
[bar (psi)]
[bar (psi)]
400 mbar (6 psi)
–0.4 (–6)
+0.4 (+6)
0.02 (0.3)
4 (60)
6 (90)
1F
1 bar (14.5 psi)
–1 (–15)
+1 (+15)
0.05 (1)
6.7 (100)
10 (150)
1H
2 bar (29 psi)
–1 (–15)
+2 (+30)
0.1 (1.5)
13.3 (200)
20 (300)
1K
4 bar (58 psi)
–1 (–15)
+4 (+60)
0.2 (3)
18.7 (280.5)
28 (420)
10 bar (145 psi)
–1 (–15)
+10 (+150)
0.5 (7.5)
26.7 (400.5)
40 (600)
40 bar (580 psi)
–1 (–15)
+40 (+600)
2 (30)
100 (1500)
160 (2400)
1S
100 bar (1450 psi)
–1 (–15)
+100 (+1500)
5 (75)
100 (1500)
400 (6000)
1U
400 bar (5800 psi)
–1 (–15)
+400 (+6000)
20 (300)
400 (6000)
600 (9000)
1W
[barabs (psiabs)]
0.01/0.04
(0.15/0.6)
1M
1P
PMP51 and PMP55 – metal process isolating diaphragm for absolute pressure
Nominal value
Range limit
Smallest
calibratable
span 5
MWP 1
OPL 2
Vacuum
resistance 3
Version in the
order code 4
lower
(LRL)
upper
(URL)
[barabs (psiabs)]
[barabs (psiabs)]
[barabs (psiabs)] [barabs (psiabs)] [barabs (psiabs)] [barabs (psiabs)]
400 mbar (6 psi)
0
+0.4 (+6)
0.02 (0.3)
4 (60)
6 (90)
2F
1 bar (14.5 psi)
0
+1 (+15)
0.05 (1)
6.7 (100)
10 (150)
2H
2 bar (29 psi)
0
+2 (+30)
0.1 (1.5)
13.3 (200)
20 (300)
2K
4 bar (58 psi)
0
+4 (+60)
0.2 (3)
18.7 (280.5)
28 (420)
10 bar (145 psi)
0
+10 (+150)
0.5 (7.5)
26.7 (400.5)
40 (600)
40 bar (580 psi)
0
+40 (+600)
2 (30)
100 (1500)
160 (2400)
2S
100 bar (1450 psi)
0
+100 (+1500)
5 (75)
100 (1500)
400 (6000)
2U
400 bar (5800 psi)
0
+400 (+6000)
20 (300)
400 (6000)
600 (9000)
2W
1)
2)
3)
4)
5)
8
Silicone oil/
Inert oil
0.01/0.04
(0.15/0.6)
2M
2P
The MWP (maximum working pressure) for the measuring device depends on the lowest-rated element, with regard
to pressure, of the selected components, i.e. the process connection ( ä 27 ff) has to be taken into consideration
in addition to the measuring cell (see Table above). Pay attention to the pressure-temperature dependence also.
For the appropriate standards and other information, see  ä 26, Pressure specifications section.
OPL: over pressure limit (= sensor overload limit)
The vacuum resistance applies to the measuring cell at reference conditions. The pressure and temperature
application limits of the selected filling oil must also be observed for the PMP55.  ä 62, "Diaphragm seal filling
oils" section.
Version in the order code  ä 69 ff, feature 70 "Sensor range"
Turn down > 20:1 can be configured in the device or on request (except analog electronics)
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Explanation of terms
Explanation of terms: turn down (TD),
set span and span based on zero point
Case 1:
• Lower range value (LRV) Upper range value
(URV)
➀=➁
LRL = LRV
URV
URL
0 bar
0.5 bar
+1 bar
Example:
• Lower range value (LRV) = 0 bar
• Upper range value (URV) = 0.5 bar (7.5 psi)
• Nominal value (URL) = 1 bar (15 psi)
➂
Turn down:
• TD = URL /URV2:1
Set span:
• URV – LRV = 0.5 bar (7.5 psi)
This span is based on the zero point.
➃=➄
P01-PMx7xxxx-05-xx-xx-xx-012
Example: 1 bar (15 psi) measuring cell
Case 2:
• Lower range value (LRV) Upper range value
(URV)
Example:
• Lower range value (LRV) = 0 bar
• Upper range value (URV) = 0.5 bar (7.5 psi)
• Nominal value (URL) = 1 bar (15 psi)
➀=➁
URV
LRV
LRL
0
–1 bar
0.5 bar
URL
+1 bar
➂
Turn down:
• TD = URL /URV= 2:1
➃
Set span:
• URV – LRV = 0.5 bar (7.5 psi)
This span is based on the zero point.
➄
P01-PMx7xxxx-05-xx-xx-xx-007.
Example: 1 bar (15 psi) measuring cell
Case 3:
• Lower range value (LRV) Upper range value
(URV)
Example:
• Lower range value (LRV) = –0.6 bar (–9 psi)
• Upper range value (URV) = 0 bar
• Nominal value (URL) = 1 bar (15 psi)
➀=➁
LRL
–1 bar
LRV
URV
URL
–0.6 bar
0
+1 bar
➂
Turn down:
• TD = URL /LRV = 1.67:1
➃
Set span:
• URV – LRV = 0.6 bar (–9 psi)
This span is based on the zero point.
➄
P01-PMx7xxxx-05-xx-xx-xx-008
Example: 1 bar (15 psi) measuring cell
1
2
3
4
5
LRL
URL
LRV
URV
Endress+Hauser
Set span
Span based on zero point
Nominal value i upper range limit (URL)
Nominal measuring range
Sensor measuring range
Lower range limit
Upper range limit
Lower range value
Upper range value
9
Cerabar M PMC51, PMP51, PMP55
Output
Output signal
• 4 to 20 mA, 2-wire
• 4 to 20 mA with superimposed digital communication protocol HART 6.0, 2-wire
Signal range
4...20 mA, 4...20 mA HART: 3.8 to 20.5 mA
Signal on alarm
As per NAMUR NE 43
• 4 to 20 mA:
– Signal overshoot: > 20.5 mA
– Signal undershoot: < 3.8 mA
– Min Alarm (3.6 mA)
• 4 to 20 mA HART
Options:
– Max. alarm: can be set from 21 to 23 mA (factory setting: 22 mA)
– Hold measured value: last measured value is held
– Min. alarm: 3.6 mA
Load - 4...20 mA and
4...20 mA HART
RLmax
[W]
1456
1239
804
➁
369
➀
11.5
30
20
RLmax £
40 45
U
[V]
U – 11.5 V
0.023 A
P01-xxxxxxxx-05-xx-xx-xx-002
Load diagram
1
2
RLmax
U
Power supply 11.5 to 30 V DC for intrinsically safe device versions
Power supply 11.5 to 45 V DC (versions with plug-in connector 35 V DC) for other types of protection and for
uncertified device versions
Maximum load resistance
Supply voltage
Note!
When operating via a handheld terminal or via a PC with an operating program, a minimum communication
resistance of 250 must be taken into account.
Resolution
Dead time,
time constant (T63)
• Current output: 1 A
• Display HART: can be set (factory setting: presentation of the maximum accuracy of the transmitter)
I
100 %
90 %
63 %
t1
t2
t
t3
P01-xxxxxxxx-05-xx-xx-xx-036
Presentation of the dead time and the time constant
10
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Dynamic behavior: 4 to 20 mA
(Analog electronics)
Dynamic behavior:
current output (HART
electronics)
Dynamic behavior: digital
output (HART electronics)
Type
Dead time t
Time constant (T63), t
Time constant (T90), t
PMC51
60 ms
40 ms
50 ms
PMP51
40 ms
40 ms
50 ms
PMP55
PMP51 + influence of the diaphragm seal
Type
Dead time t
Time constant (T63), t
PMC51
90 ms
120 ms
PMP51
60 ms
70 ms
PMP55
PMP51 + influence of the diaphragm seal
Dead time, time constant (T63)
A typical configuration for the PLC of 2 to 3 values per second results in the following total dead time:
Type
Dead time t
Time constant (T63), t
PMC51
340 ms
120 ms
PMP51
310 ms
70 ms
PMP55
PMP51 + influence of the diaphragm seal
Reading cycle
HART commands: 2 to 3 per second on average.
The Cerabar M commands the BURST MODE function for cyclic value transmission via the HART
communication protocol.
Response time
 250 ms
Cycle time (update time)
On average 310 to 520 ms.
Damping
A damping affects all outputs (output signal, display).
• Analog electronics: via DIP switch on the electronic insert,
switch position "on" = 2s; switch position "off" = 0s
• HART: via DIP switch on the electronic insert, switch position "on" = value set in the software (factory
setting: 2 s) and "off". Via local display, handheld terminal or PC with operating program, continuous from
0 to 999 s
Endress+Hauser
11
Cerabar M PMC51, PMP51, PMP55
Power supply
Electrical connection
Note!
• When using the measuring device in hazardous areas, installation must comply with the corresponding
national standards and regulations and the Safety Instructions or Installation or Control Drawings.
 ä 85 ff, "Safety Instructions" and "Installation/Control Drawings" sections.
• HART: Overvoltage protection HAW569Z for the non-hazardous area and for ATEX II 1/2 G Exi can be
ordered as an option (see "Ordering information" section).
• Protective circuits against reverse polarity, HF influences and overvoltage peaks are installed.
4 to 20 mA, 4 to 20 mA HART
5
1
2
- +
4
3
4…20 mA
11.5 V DC
6
P01-xMx5xxxx-04-xx-xx-xx-004
Electrical connection
1
2
3
4
5
6
Housing
External ground terminal
Internal ground terminal
Power supply terminals
Test terminals, see "Taking 4 to 20 mA test signal" section
Minimum supply voltage = 11.5 V DC
Taking 4 to 20 mA test signal
A 4 to 20 mA test signal may be measured via the test terminals without interrupting the measurement.
12
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Devices with valve connector
+ –
–
+
+ –
P01-xMx5xxxx-04-xx-xx-xx-005
Left: electrical connection for devices with a valve connector
Right: view of the connector at the device
Devices with Harting connector Han7D
+
+ –
–
7
8
6
1
2
5
3
Han7D
4
+–
P01-xxx7xxxx-04-xx-xx-xx-001
Left: electrical connection for devices with a Harting connector Han7D
Right: view of the connector at the device
Devices with M12 connector
+ –
–
+
M12
+–
P01-xxx7xxxx-04-xx-xx-xx-000
Left: electrical connection for devices with an M12 connector
Right: view of the connector at the device
Endress+Hauser offers the following accessories for devices with an M12 connector:
Plug-in jack M 12x1, straight
• Material: body PA; coupling nut CuZn, nickel-plated
• Degree of protection (fully locked): IP67
• Order number: 52006263 or through device order, see also  ä 69 ff "Ordering information" section
Plug-in jack M 12x1, elbowed
• Material: body PBT; coupling nut CuZn, nickel-plated
• Degree of protection (in screwed situation): IP67
• Order number: 71091284 or through device order, see also  ä 69 ff "Ordering information" section
Endress+Hauser
13
Cerabar M PMC51, PMP51, PMP55
Cable 4x0.34 mm2 (20 AWG) with M12 socket, elbowed, screw plug, 5 m (16 ft) length
• Material: body PUR; coupling nut CuSn/Ni; cable PVC
• Degree of protection (fully locked): IP67
• Order number: 52010285 or through device order, see also  ä 69 ff "Ordering information" section
Devices with 7/8" connector
–
+ –
+
7/8”
+–
P01-xxx7xxxx-04-xx-xx-xx-003
Left: electrical connection for devices with a 7/8" connector
Right: view of the connector at the device
Cable gland
Approval
Standard, II1/2G Exia, IS
ATEX II1/2D, II1/2GD Exia, II3G Ex nA
Type
Clamping area
Plastic M20x1.5
5 to 10 mm (0.2 to 0.39 in)
Metal M20x1.5 (Ex e)
7 to 10.5 mm (0.28 to 0.41 in)
Terminals
For wire cross-sections of 0.5 to 2.5 mm² (20...14 AWG).
Supply voltage
Note!
• When using the measuring device in hazardous areas, installation must comply with the corresponding
national standards and regulations and the Safety Instructions or Installation or Control Drawings.
• All explosion protection data are given in separate documentation which is available upon request. The Ex
documentation is supplied as standard with all devices approved for use in explosion hazardous areas.
 ä 85 ff, "Safety Instructions" and "Installation/Control Drawings" sections.
4 to 20 mA, 4 to 20 mA HART
• 11.5 to 45 V DC
(Versions with plug-in connection 35 V DC)
• For intrinsically save device versions: 11.5 to 30 V DC
Cable entry
 ä 69 ff, feature 50 "Electrical connection".
Cable specification
• Endress+Hauser recommends using twisted, shielded two-wire cables.
• Terminals for wire cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG)
• Cable outer diameter: 5 to 9 mm (0.2 to 0.35 in)
Residual ripple
No influence on 4 to 20 mA signal up to 5 % residual ripple within the permitted voltage range [according to
HART hardware specification HCF_SPEC-54 (DIN IEC 60381-1)]
Influence of power supply
0.0006% of URL/1 V
14
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Performance characteristics – general
Reference operating
conditions
•
•
•
•
•
•
•
•
•
•
•
•
Uncertainty of measurement
for small absolute pressure
ranges
The smallest expanded uncertainty of measurement that can be returned by our standards is:
• 0.4% of the set span in the range of 1 to 30 mbar
• 1% of the set span in the range < 1 mbar.
Long-term stability
As per IEC 60770
Ambient temperature TA = constant, in the range of: +21 to +33°C (+70 to +91°F)
Humidity = constant, in the range of: 5 to 80 % RH
Ambient pressure pA = constant, in the range of: 860 to 1060 mbar (12.47...15.37psi)
Position of the measuring cell: constant, in range: 1° horizontally
Input of LOW SENSOR TRIM and HIGH SENSOR TRIM for lower range value and upper range value
Span based on zero point
Material of the process isolating diaphragm PMC51: Al2O3 (aluminum-oxide ceramic, Ceraphire®)
Material of the process isolating diaphragm PMP51 and PMP55: AISI 316L
Filling oil PMP51 and PMP55: silicone oil
Supply voltage: 24 V DC ± 3 V DC
Load with HART: 250 
PMC51
Long-term stability of
URL / 1 year
Long-term stability of
URL / 5 years
Long-term stability of
URL / 10 years
< 1 bar (15 psi)
±0.2 %
±0.4 %
±0.5 %
> 1 bar (15 psi)
±0.1 %
±0.25 %
±0.4 %
Long-term stability of
URL / 1 year
Long-term stability of
URL / 5 years
Long-term stability of
URL / 10 years
< 1 bar (15 psi)
±0.2 %
±0.4 %
±0.5 %
> 1 bar to 10 bar (15 to 150 psi)
±0.1 %
±0.175 %
±0.4 %
40 bar (600 psi)
±0.1 %
±0.2 %
±0.4 %
100 bar (1500 psi)
±0.1 %
±0.25 %
±0.2 %
400 bar (6000 psi)
±0.1 %
±0.25 %
±1.0 %
PMP51
Influence of orientation
• PMC51 1:  0.2 mbar (3 psi)
• PMP51 1.2
–  4 mbar (0.06 psi) for process connections with 1/2" thread and silicone oil
–  10 mbar (0.15 psi) for process connections with > thread 1/2" and flanges
1)
2)
Device rotated 180°, process connection pointing upwards.
This value is doubled for inert oil.
Note!
Position-dependent zero point shift can be corrected at the device.  ä 19, "General installation instructions"
section and  ä 67 ff, "Installation instructions" section.
Warm-up period
Endress+Hauser
• 4 to 20 mA: <1,5 s
• 4 to 20 mA HART: <5 s
15
Cerabar M PMC51, PMP51, PMP55
Performance characteristics – ceramic process isolating
diaphragm
Reference accuracy – PMC51
The reference accuracy comprises the non-linearity according to limit point setting, hysteresis
and non-reproducibility as per IEC 60770. The data refer to the calibrated span.
Gauge pressure sensors
Measuring cell
Standard reference accuracy
Platinum reference accuracy
100 mbar (1.5 psi)
• TD 1:1 to TD 10:1: 0.15 %
• TD > 10:1 to TD 20:1: 0.20 %
• TD 1:1 to TD 10:1: ±0.075 %
• TD > 10:1 to TD 13:1: ±0.1 %
• TD 1:1 to TD 10:1: 0.15 %
• TD > 10:1 to TD 20:1: 0.20 %
• TD 1:1 to TD 10:1: ±0.075 %
• TD > 10:1 to TD 20:1: ±0.1 %
• TD 1:1 to TD 10:1: 0.15 %
• TD > 10:1 to TD 20:1: 0.20 %
• TD 1:1 to TD 10:1: ±0.075 %
• TD > 10:1 to TD 13:1: ±0.1 %
250 mbar (4 psi), 400 mbar (6 psi),
1 bar (15 psi), 2 bar (30 psi),
4 bar (60 psi), 10 bar (150 psi)
40 bar (600 psi)
Absolute pressure sensors
Measuring cell
Standard reference accuracy
Platinum reference accuracy
100 mbar (1.5 psi)
• TD 1:1 to TD 10:1: 0.15 %
• TD > 10:1 to TD 13:1: 0.20 %
• TD 1:1 to TD 5:1: ±0.075 %
• ---
250 mbar (4 psi)
• TD 1:1 to TD 10:1: 0.15 %
• TD > 10:1 to TD 20:1: 0.20 %
• TD 1:1 to TD 10:1: ±0.075 %
• TD > 10:1 to TD 13:1: ±0.1 %
• TD 1:1 to TD 10:1: 0.15 %
• TD > 10:1 to TD 20:1: 0.20 %
• TD 1:1 to TD 10:1: ±0.075 %
• TD > 10:1 to TD 20:1: ±0.1 %
• TD 1:1 to TD 10:1: 0.15 %
• TD > 10:1 to TD 20:1: 0.20 %
• TD 1:1 to TD 10:1: ±0.075 %
• TD > 10:1 to TD 13:1: ±0.1 %
400 mbar (6 psi), 1 bar (15 psi),
2 bar (30 psi), 4 bar (60 psi),
10 bar (150 psi)
40 bar (600 psi)
Total performance – PMC51
(digital output)
The "Total performance" specification comprises the non-linearity including hysteresis, non-reproducibility as
well as the thermal change in the zero point. All specifications apply to the temperature range –10 to +60°C
(+14 to +140°F).
Measuring cell
Total error - PMC51
% URL
100 mbar (1.5 psi), 250 mbar (4 psi), 400 mbar (6 psi)
TD 1:1: ±0.2
1 bar (15 psi), 2 bar (30 psi), 4 bar (60 psi), 10 bar (150 psi), 40 bar (600 psi)
TD 1:1: ±0.15
The total error comprises the long-term stability and the total performance:
Measuring cell
Thermal change in the zero
output and the output span –
PMC51
% URL/year
100 mbar (1.5 psi), 250 mbar (4 psi), 400 mbar (6 psi)
±0.25
1 bar (15 psi), 2 bar (30 psi), 4 bar (60 psi), 10 bar (150 psi), 40 bar (600 psi)
±0.2
Measuring cell
–10 to +60 °C
(+14 to +140°F)
–20 to –10 °C, +60 to +100 °C
(–4 to +14°F, +140 to +212°F)
% of the calibrated measuring span
16
100 mbar (1.5 psi), 250 mbar (4 psi),
400 mbar (6 psi)
(0.088 + 0.088 x TD)
(0.138 + 0.138 x TD)
1 bar (15 psi), 2 bar (30 psi), 4 bar (60 psi),
10 bar (150 psi), 40 bar (600 psi)
(0.088 + 0.04 x TD)
(0.175 + 0.075 x TD)
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Performance characteristics – metal process isolating
diaphragm
Reference accuracy – PMP51,
PMP55 without capillary
The reference accuracy comprises the non-linearity according to limit point setting, hysteresis and nonreproducibility as per IEC 60770. The data refer to the calibrated span.
Gauge pressure sensors/absolute pressure sensors
Measuring cell
Reference accuracy – PMP55
with capillary (digital output)
Endress+Hauser
Standard reference accuracy
Platinum reference accuracy
400 mbar (6 psi)
• TD 1:1 to TD 1:1: ±0.15 %
• TD >1:1: ±0.15 % x TD
• 
• 
1 bar (15 psi)
• TD 1:1 to TD 5:1: ±0.15 %
• TD >5:1: ±0.03 % x TD
• TD 1:1 to TD 2.5:1: ±0.075 %
• 
2 bar (30 psi)
• TD 1:1 to TD 10:1: ±0.15 %
• TD >10:1 to TD 13:1: ±0.20 %
• TD 1:1 to TD 5:1: ±0.075 %
• 
4 bar (60 psi)
• TD 1:1 to TD 10:1: ±0.15 %
• TD >10:1 to TD 20:1: ±0.20 %
• TD 1:1 to TD 10:1: ±0.075 %
• TD > 10:1 to TD 13:1: ±0.1 %
10 bar (150 psi),
40 bar (600 psi)
• TD 1:1 to TD 10:1: ±0.15 %
• TD >10:1 to TD 20:1: ±0.20 %
• TD 1:1 to TD 10:1: ±0.075 %
• TD > 10:1 to TD 20:1: ±0.1 %
100 bar (1500 psi)
• TD 1:1 to TD 10:1: ±0.15 %
• TD >10:1 to TD 20:1: ±0.20 %
• TD 1:1 to TD 10:1: ±0.075 %
• TD > 10:1 to TD 13:1: ±0.1 %
400 bar (6000 psi)
• TD 1:1 to TD 5:1: ±0.15 %
• TD >5:1: ±0.03 % x TD
• 
• 
The reference accuracy comprises the non-linearity according to limit point setting, hysteresis and
non-reproducibility as per IEC 60770. The data refer to the calibrated span.
Measuring cell
Sensor
% of the set span
400 mbar (6 psi)
Gauge pressure / Absolute pressure
• TD 1:1
• TD > 1:1
=
=
±0.15
±0.15 x TD
1 bar (15 psi)
Gauge pressure / Absolute pressure
• TD 1:1 to TD 2.5:1
• TD > 2.5:1
=
=
±0.1
±0.04 x TD
2 bar (30 psi)
Gauge pressure
• TD 1:1 to TD 2.5:1
• TD > 2.5:1
=
=
±0.1
±0.04 x TD
2 bar (30 psi)
Absolute pressure
• TD 1:1 to TD 5:1
• TD > 5:1
=
=
±0.075
±0.015 x TD
4 bar (60 psi)
Gauge pressure / Absolute pressure
• TD 1:1 to TD 10:1
• TD > 10:1
=
=
±0.075
±0.0075 x TD
10 bar (150 psi),
40 bar (600 psi)
Gauge pressure / Absolute pressure
• TD 1:1 to TD 15:1
• TD > 15:1
=
=
±0.075
±0.005 x TD
100 bar (1500 psi)
Gauge pressure / Absolute pressure
• TD 1:1 to TD 10:1
• TD > 10:1
=
=
±0.075
±0.0075 x TD
400 bar (6000 psi)
Gauge pressure / Absolute pressure
• TD 1:1 to TD 5:1
• TD > 5:1
=
=
±0.15
±0.03 x TD
17
Cerabar M PMC51, PMP51, PMP55
Total performance – PMP51
The "Total performance" specification comprises the non-linearity including hysteresis, non-reproducibility as
well as the thermal change in the zero point. All specifications apply to the temperature range –10 to +60°C
(+14 to +140°F) and Turndown 1:1.
Measuring cell
PMP51
PMP51 with gold/rhodium-coated
process isolating diaphragm
% of URL
400 mbar (6 psi)
±0.34
1 bar (15 psi)
±0.75
2 bar (30 psi)
±0.45
4 bar (60 psi)
±0.25
10 bar (150 psi), 40 bar (600 psi),
100 bar (1500 psi)
400 bar (6000 psi)
Total error - PMP51
Thermal change in the zero
output and the output span –
PMP51 and PMP55
±1.25
±0.3
±0.25
±0.4
±0.4
The total error comprises the long-term stability and the total performance. All specifications apply to the
temperature range –10 to +60°C (+14 to +140°F) and Turndown 1:1.
Measuring cell
% of URL/year
400 mbar (6 psi)
±0.44
1 bar to 100 bar (15 psi to 1500 psi)
±0.35
400 bar (6000 psi)
±0.5
Note!
When using a PMP55, the influence from the respective diaphragm seal must also be taken into account
( ä 61 ff "Planning instructions for diaphragm seal systems" and  ä 39 ff "Process connections PMP55
(with metal process isolating diaphragm)".
PMP51 and PMP55 (basic device)
The data refer to the calibrated span.
Measuring cell
–10 to +60°C
(+14 to +140°F)
–40 to –10°C, +60 to +85°C
(–40 to +14°F, +140 to +185°F)
400 mbar (6 psi)
±(0.2 + 0.015 x TD)
±(0.4 + 0.03 x TD)
1 bar (15 psi), 2 bar (30 psi), 4 bar
(60 psi), 10 bar (150 psi), 40 bar
(600 psi)
±(0.15 + 0.15 x TD)
±(0.25 + 0.25 x TD)
±(0.02 + 0.35 x TD)
±(0.04 + 0.7 x TD)
100 bar (1500 psi)
400 bar (6000 psi)
18
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Operating conditions (installation)
General installation
instructions
• The position-dependent zero point shift can be corrected:
– directly at the device via an operating key on the electronic insert
– directly at the device via operating keys on the display (except analog electronics)
– via digital communication if the cover is not open (except analog electronics)
Note!
In hazardous areas, comply strictly with the safety instructions when the housing cover is closed and open.
• Endress+Hauser offers a mounting bracket for installing the device on pipes or walls.
See also  ä 20, "Wall and pipe mounting" section.
• Use flushing rings for flange and cell diaphragm seals if medium buildup or clogging can be expected at the
diaphragm seal connection. The flushing ring can be inserted between the process connection and the
diaphragm seal. Thanks to the two lateral flushing bore holes, material buildup in front of the process
isolating diaphragm can be rinsed away and the pressure chamber can be ventilated.
Measuring arrangement for
devices without diaphragm
seal – PMC51, PMP51
Cerabar M transmitters without diaphragm seals are mounted as per the norms for a manometer
(DIN EN 837-2). We recommend the use of shutoff devices and siphons. The orientation depends on the
measuring application.
Pressure measurement in gases
• Mount Cerabar M with shutoff device above the tapping point so that any condensate can flow into the
process.
Pressure measurement in steams
• Mount Cerabar M with siphon below the tapping point.
• Fill the siphon with liquid before commissioning.
The siphon reduces the temperature to almost the ambient temperature.
Pressure measurement in liquids
• Mount Cerabar M with shutoff device below or at the same level as the tapping point.
Level measurement
• Mount Cerabar M below the lowest measuring point (zero point of the measurement).
• Do not mount the device at the following positions: In the filling curtain, in the tank outlet or at a point in
the container which could be affected by pressure pulses from an agitator or a pump.
• The calibration and functional test can be carried out more easily if you mount the device downstream of a
shutoff device.
Measuring arrangement for
devices with diaphragm seal
– PMP55
• For PMP55:  ä 67, "Installation instructions" section.
• The diaphragm seals also shift the zero point, depending on the installation position.
(See also  ä 67, "Installation instructions" section).
Thermal insulation – PMP55
The PMP55 may only be insulated up to a certain height. The maximum permitted insulation height is
indicated on the devices and applies to an insulation material with a heat conductivity  0.04 W/(m x K) and
to the maximum permitted ambient and process temperature ( see table below). The data were determined
under the most critical application "quiescent air".
TA
l £ 0.04 W
m•K
TP
P01-PMx5xxxx-11-xx-xx-en-010
Maximum permitted insulation height, here indicated on a PMP55 with a flange
Endress+Hauser
19
Cerabar M PMC51, PMP51, PMP55
PMP55
Mounting with temperature
isolator
Ambient temperature (TA)
70°C (158°F)
Process temperature (TP)
Max. 400°C (752°F), depending on the diaphragm seal filling oil used ( ä 62)
Endress+Hauser recommends the use of temperature isolators in the event of constant extreme medium
temperatures which lead to the maximum permissible electronics temperature of +85°C (+185°F) being
exceeded.
Depending on the filling oil used, Cerabar M devices with temperature isolators can be used for maximum
temperatures of up to 260°C (+500°F). For the temperature application limits of filling oils, see  ä 62,
"Diaphragm seal filling oils" section.
To minimize the influence of rising heat, Endress+Hauser recommends the device be mounted horizontally or
with the housing pointing downwards.
The additional installation height also brings about a maximum zero point shift of 21 mbar (0.315 psi) due to
the hydrostatic column in the temperature isolator. You can correct this zero point shift at the device.
max. 115
P01-PMx5xxxx-11-xx-xx-xx-001
PMP55 with temperature isolator
52
133
Endress+Hauser offers a mounting bracket for installing the device on pipes or walls.
See also  ä 69 ff, feature 620, "Accessory enclosed", version "PA".
119
Wall and pipe mounting
70
P01-xMx5xxxx-06-xx-xx-xx-001
20
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
"Separate housing" version
With the "separate housing" version, you are able to mount the housing with the electronics insert at a distance
from the measuring point. This allows for trouble-free measurement:
• Under particularly difficult measuring conditions (at installation locations that are cramped or difficult to
access)
• If extreme cleaning of the measuring point is required
• If the measuring point is exposed to vibrations
You can choose between different cable versions:
• PE (2 m (6.6 ft), 5 m (16 ft) and 10 m (33 ft))
• FEP (5 m (16 ft)).
 ä 69 ff, feature 600, "Separate housing".
For the dimensions,  ä 54.
➃
➂
IP xx
(see chapter
“Ordering information”)
FEP cable:
IP 69K
IP 66/68 NEMA 4/6P
PE cable:
IP 66/68 NEMA 4/6P
➀
➁
r ³ 120 mm
P01-PMx5xxxx-11-xx-xx-en-002
In the case of the "separate housing" version, the sensor is delivered with the process connection and cable ready
mounted. The housing and a mounting bracket are enclosed as separate units. The cable is provided with a socket at both
ends. These sockets are simply connected to the housing and the sensor.
1
2
3
4
Process connection with sensor
Cable, both ends are fitted with a socket
Mounting bracket provided, suitable for pipe and wall mounting
Housing with electronic insert
Degree of protection for the process connection and sensor when using:
• FEP cable:
– IP 69K
– IP 66/68 NEMA 4/6P
• PE cable:
– IP 66/68 NEMA 4/6P
Technical data of the PE and FEP cable:
• Minimum bending radius: 120 mm (4.72 in)
• Cable extraction force: max. 450 N (101 lbf)
• Resistance to UV light
Use in hazardous area:
• Intrinsically safe installations (Ex ia/IS)
• FM/CSA IS: for Div.1 installation only
Installation conditions
General conditions
• Installation without insulation
• Ambient temperature: max. 50 °C (122°F)
Endress+Hauser
21
Cerabar M PMC51, PMP51, PMP55
Oxygen applications
Oxygen and other gases can react explosively to oils, grease and plastics. As a result, the following are some of
the precautions that must be taken:
– All components of the system, such as measuring devices, must be cleaned in accordance with the BAM
(DIN 19247) requirements.
– Depending on the materials used, a certain maximum temperature and maximum pressure must not be
exceeded for oxygen applications.
The devices suitable for gaseous oxygen applications are listed in the following table with the specification pmax.
Ordering information for devices
cleaned for oxygen applications
pmax for oxygen applications
Tmax for
oxygen
applications
PMC51 1) – devices with sensors,
nominal value < 10 bar (150 psi)
Over pressure limit (OPL) of sensor2, 3
60°C (140°F)
PMC51 ) – devices with sensors,
nominal value  10 bar (150 psi)
40 bar (600 psi)
60°C (140°F)
PMP51 PMP55 )
Depends on the lowest-rated element, with regard to
pressure, of the selected components: over pressure limit
(OPL) of sensor , process connection (1.5 x PN) or fill fluid
(160 bar (2320 psi))
85°C (185°F)
1)
Feature 570 "Service" version "HB"
2)
 ä 69 ff "Ordering information", feature 70 "Sensor range"
3)
PMC51 with PVDF thread or PVDF flange pmax = 15 bar (225 psi)
Silicone-free applications
Special cleaning of the transmitter to remove paint-wetting substances, for use in paint shops  ä 72
feature 570 "Service", version "HC".
Ultrapure gas applications
Endress+Hauser also provides devices which have been cleaned of oil and grease for special applications, such
as ultrapure gas. No special restrictions regarding the process conditions apply to this device.
 ä 69 ff, "Ordering information PMC51", feature 570 "Service" version "HA".
 ä 75 ff, "Ordering information PMP51", feature 570 "Service" version "HA".
Applications with hydrogen
With regard to materials in which hydrogen formation takes place, hydrogen atoms can diffuse through the
metal process isolating diaphragm. This can result in incorrect measurement results.
Endress+Hauser offers process isolating diaphragms with a gold/rhodium coating for such instances.
 ä 74 ff "Ordering information PMP51" and  ä 79 ff "Ordering information PMP55",
feature 170 "Material of the process isolating diaphragm" version "M".
22
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Operating conditions (environment)
Ambient temperature range
Version
PMC51
Without LCD display
With LCD display
–20°C to +70°C (-4°F to +158°F)
With M12 plug , elbowed
For thermally decoupled
diaphragm seals (observe
filling oil)
PMP55
–40°C to +85°C (-40°F to +185°F)
1
With separate housing (PE
and FEP cable)
PMP51
-25°C to +85°C (-13°F to +185°F)
–40°C to +50°C (-40°F to +122°F)

2


 ä 62
1)
Extended temperature application range (-40°C to +85°C (–40°F to +185°F)) with restrictions in optical properties
such as display speed and contrast
2)
Seal system FEP cable/separate housing sensor for IP69K limits the temperature range
Note!
For high-temperature applications, either a PMP55 with a temperature isolator or with a capillary can be used.
If vibrations also occur in the application, Endress+Hauser recommends you use a PMP55 with a capillary. If
a PMP55 with a temperature isolator or capillary is used, we recommend a suitable bracket for mounting (see
"Wall and pipe mounting" section on  ä 20).
For devices for use in hazardous areas, see Safety Instructions, Installation or Control Drawing. ( ä 85 ff,
"Safety Instructions" and "Installation/Control Drawings" sections)
Storage temperature range
Version
PMC51
PMP51
Without LCD display
–40°C to +90°C (-40°F to +194°F)
With LCD display
–40°C to +85°C (-40°F to +185°F)
With M12 plug , elbowed
-25°C to +85°C (-13°F to +185°F)
With separate housing and
FEP cable
For thermally decoupled
diaphragm seals (observe
filling oil)
1)
–40°C to +60°C (-40°F to +140°F)

1

PMP55

 ä 62
Seal system FEP cable/separate housing sensor for IP96K limits the temperature range
Degree of protection
•  ä 69 ff, feature 50 "Electrical connection".
• Separate housing ( ä 21)
Climate class
Class 4K4H (air temperature: –20 to 55°C (–4 to +131°F), relative humidity: 4 to 100%) satisfied as per
DIN EN 60721-3-4 (condensation possible 1)
1)
Endress+Hauser
In the case of the PMC51, condensate in the device must be avoided (avoid moisture collecting in the device).
23
Cerabar M PMC51, PMP51, PMP55
Vibration resistance
Device/Additional
option
Test standard
Vibration resistance
PMC51, PMP51, PMP55
GL VI-7-2
• Part 7: Guidelines for the Performance of Type
Approvals
• Chapter 2: Test Requirements for Electrical /
Electronic Equipment and Systems
guaranteed for
3...18 Hz: ±4 mm (0.16 in);
25...500 Hz: 5 g
in all 3 planes
with mounting bracket
IEC 61298-3
IEC 60068-2-6
guaranteed for
10...58 Hz: ±0.15 mm (0.01 in);
58...500 Hz: 2 g
in all 3 planes
Note!
For high-temperature applications, either a PMP55 with a temperature isolator or with a capillary can be used.
If vibrations also occur in the application, Endress+Hauser recommends you use a PMP55 with a capillary. If
a PMP55 with a temperature isolator or capillary is used, we recommend a suitable bracket for mounting (see
"Wall and pipe mounting" section on  ä 20).
Electromagnetic compatibility
• Electromagnetic compatibility as per all the relevant requirements of the EN 61326 series and NAMUR
Recommendation EMC (NE21). Details can be found in the Declaration of Conformity (in the Download
area of "www.de.endress.com", "search area - Approvals and Certificates", "Manufact. Declaration").
• Maximum deviation: < 0.5 % of span
Overvoltage protection
(optional)
The device can be fitted with overvoltage protection, see  ä 69 ff "Ordering information" feature 610
"Accessory mounted:" version "NA". The overvoltage protection is mounted at the factory on the housing
thread (M20x1.5) for the cable gland and is approx. 70 mm (2,76 in) in length (take additional length into
account when installing). The device is connected as illustrated in the following graphic.
For details refer to TI103R/09/en, XA036R/09/a3 and KA161R/09/a6.
Wiring
Incoming
connection cables
+
➀
Unit to be
protected
-
+
➁
Red
Black
-
+
-
Connection
cables
Shield grounding
➀ without
➁ direct
HAW569Z
P01-xMx5xxxx-04-xx-xx-en-006
24
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Operating conditions (process)
Process temperature limits
PMC51 (with ceramic process isolating diaphragm)
• –20 to +100 °C (–4 to +212°F)
• Observe the process temperature range of the seal. See also the following section "Process temperature range,
seals".
Extreme jumps in temperature can result in temporary measuring errors. Temperature compensation takes effect after several
minutes. Internal temperature compensation is faster the smaller the jump in temperature and the longer the time interval
involved.
PMP51 (with metal process isolating diaphragm)
Description
Temperature operating range
Process connections with internal process isolating diaphragm
–40 to +125°C (–40 to +257°F)
Process connections with flush-mounted process isolating diaphragm,
G 1 A, G 1 1/2 A, G 2 A, 1 NPT, 1 1/2 NPT, 2 NPT,
M 44 x 1.25, EN/DIN, ANSI and JIS flanges
–40 to +100°C (–40 to +212°F)
Process connections with flush-mounted process isolating diaphragm,
G 1/2 A, M 20x1.5
–20 to +85°C (–4 to +185°F)
PMP55 (with metal process isolating diaphragm)
• Depending on the diaphragm seal and filling oil from -70°C (-94°F) up to +400°C (+752°F). Observe the
temperature application limits of the diaphragm seal oil.  ä 62, "Diaphragm seal filling oils" section.
Note!
• Do not use diaphragm seals with 0.09 mm (0.0035 in) PTFE foil on AISI 316L for vacuum applications,
upper temperature limit +204°C (+399°F).
• For oxygen applications, observe  ä 22, "Oxygen applications" section.
Process temperature range,
seals
PMC51 (with ceramic process isolating diaphragm)
Version for feature
Seal
190 in the order code
Process temperature range
A
-20 to +125°C (-4 to +257°F)
A
Endress+Hauser
FKM Viton
1)
FKM Viton, cleaned for O2 application
-5 to +60°C (+23 to +140°F)
B
FKM Viton, FDA
-20 to +125°C (-4 to +257°F)
F 2)
NBR
-10 to +100°C (-14 to +212°F)
G
HNBR, FDA, 3A Class II, KTW, AFNOR, BAM
-25 to +125°C (-13 to +257°F)
J
EPDM
-20 to +125°C (-4 to +257°F)
K
EPDM, FDA, 3A Class II, USP Class VI, DVGW, KTW,
W270, WRAS, ACS, NSF61
-20 to +125°C (-4 to +257°F)
1)
With feature 570 "Service", version "HB - Cleaned for oxygen service"
2)
For devices with NBR or HNBR seals, the values for "Total performance – PMC51 (digital output)" ( ä 16) and
"Thermal change in the zero output and the output span – PMC51" ( ä 16) must be multiplied by a factor of 3.
25
Cerabar M PMC51, PMP51, PMP55
Pressure specifications
• The maximum pressure for the measuring device depends on the lowest-rated element with regard to
pressure. See the following sections:
–  ä 7 ff, "Measuring range" section
– "Mechanical construction" section.
The MWP (maximum working pressure) is specified on the nameplate. This value refers to a reference
temperature of +20°C (68°F) or 100°F (38°C) for ANSI flanges and may be applied to the device for an
unlimited time. Observe temperature dependency.
• The pressure values permitted at higher temperatures can be found in the following standards:
– EN 1092-1: 2001 Tab. 18 1
– ASME B 16.5a – 1998 Tab. 2-2.2 F316
– ASME B 16.5a – 1998 Tab. 2.3.8 N10276
– JIS B 2220.
• The test pressure corresponds to the over pressure limit of the device (over pressure limit OPL = 1.5 x MWP
2) and may be applied for only a limited time period in order to avoid permanent damage.
• The Pressure Equipment Directive (EC Directive 97/23/EC) uses the abbreviation "PS". The abbreviation
"PS" corresponds to the MWP (maximum working pressure) of the measuring device.
• In the case of sensor range and process connection combinations where the OPL (over pressure limit) of the
process connection is smaller than the nominal value of the sensor, the device is set at the factory, at the
very maximum, to the OPL value of the process connection. If you want to use the entire sensor range, select
a process connection with a higher OPL value (1.5 x PN; PN = MWP).
• In oxygen applications, the values for "pmax and Tmax for oxygen applications" as per  ä 22, "Oxygen
applications" may not be exceeded.
1)
2)
26
With regard to their stability-temperature property, the materials 1.4435 and 1.4404 are grouped together under 13EO
in EN 1092-1 Tab. 18. The chemical composition of the two materials can be identical.
The equation does not apply for PMP51 and PMP55 with a 40 bar (600 psi) or a 100 bar (1500 psi) measuring cell.
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Mechanical construction
F31 aluminum housing
dimensions
115
94
103
H
15
➀
P01-F31xxxx-06-00-xx-xx-000
Front view, left-hand side view, top view
➀ The cover with viewing window is 15 mm (0.59 in) higher than the cover without viewing window.
 For installation height H for housing with viewing window, see the specific process connection. Housing weight
 ä 55
F15 stainless steel housing
dimensions
100
H
19
➀
76
P01-F15xxxx-06-00-xx-xx-000
Front view, top view.
➀ The cover with viewing window is 19 mm (0.75 in) higher than the cover without viewing window.
 For installation height H for housing with viewing window, see the specific process connection. Housing weight
 ä 55
Thread, internal process isolating diaphragm
H
➂
G 1/2A 11.4 mm
17
20
3
ø3
ø6
G 1/2
13
17
20
ø8
G 1/2A G 1/4
H
➁
G 1/2A
H
➀
17
20
Process connections PMC51
(with ceramic process
isolating diaphragm)
G 1/4
ø17.5
G 1/2
ø11.4
ø17.5
G 1/2
P01-PMC71xxx-06-09-xx-xx-001
Process connections PMC51, thread ISO 228
Installation height H  ä 28.
1
2
3
Endress+Hauser
Thread ISO 228 G 1/2 A EN 837;
Material version GCJ: AISI 316L, version GCC: Alloy C276
Version GCF: PVDF (max.: 15 bar (217.5 psi), –10 to +60 °C (+14 to +140 °F)), mount version"GCF" with a
mounting bracket only (  ä 20); weight: 0.63 kg (1.39 lbs)
Thread ISO 228 G 1/2 A G 1/4 (female);
Material version GLJ: AISI 316L, version GLC: Alloy C276; weight: 0.63 kg(1.39 lbs)
Thread ISO 228 G 1/2 A hole 11.4 mm (0.45 in);
Material version GMJ: AISI 316L, version GMC: Alloy C276; weight: 0.63 kg(1.39 lbs)
27
Cerabar M PMC51, PMP51, PMP55
11.4 mm
ø11.4
1/4 NPT
1/2 NPT
➃ 1/2 FNPT
H
3 mm
25
25
25
H
➂ 1/2 MNPT
H
➁ 1/2 MNPT
25
1/4 FNPT
H
➀ 1/2 MNPT
ø11.4
1/2 NPT
1/2 NPT
ø3
1/2 NPT
ø26.5
P01-PMC71xxx-06-09-xx-xx-002
Process connections PMC51, thread ANSI
Installation height H  ä 28.
1
2
3
4
Thread ANSI 1/2 MNPT 1/4 FNPT;
Material version RLJ: AISI 316L, version RLC: Alloy C276; weight: 0.63 kg (1.39 lbs)
Thread ANSI 1/2 MNPT hole 11.4 (0.45 in);
Material version RKJ: AISI 316L; version RKC: Alloy C276; weight: 0.63 kg(1.39 lbs)
Thread ANSI 1/2 MNPT hole 3 mm (0.12 in);
Material version RJF: PVDF (max.: 15 bar (225 psi), –10 to +60 °C (+14 to +140 °F)) mount with mounting bracket
only ( ä 20); weight: 0.63 kg (1.39 lbs)
Thread ANSI FNPT 1/2
Material version R1J: AISI 316L, version R1C: Alloy C276; weight: 0.63 kg(1.39 lbs)
➁
G 1/2
R 1/2
ø3
ø5
3
23
13.2
20
ø8
H
H
➀
ø11.4
R 1/2
G 1/2
P01-PMC71xxx-06-09-xx-xx-003
Process connections PMC51, thread JIS
Installation height H  ä 28.
1
2
Version GNJ: thread JIS B0202 G 1/2 (male), material: AISI 316L; weight: 0.63 kg (1.39 lbs)
Version GOJ: thread JIS B0203 R 1/2 (male), material: AISI 316L; Weight: 0.63 kg (1.39 lbs)
Installation height H for devices with threaded connection and internal process isolating diaphragm
28
F31 housing
F15 housing
154 mm (6.06 in)
146 mm (5.75 in)
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Thread, flush-mounted process isolating diaphragm
➀ G 1 1/2
➁
G2
30
25
28
33.5
H
SW 60
60 AF
H
SW 60
60 AF
G2
ø68
➂ 1 1/2 NPT
➃
➄ M44x1.25
2 NPT
2 NPT
ø68
H
H
SW 60
60 AF
11
30
1 1/2 NPT
33.5
SW 60
60 AF
27
H
SW 60
60 AF
22
G 1 1/2
ø55
ø40.5
M44x1.25
P01-PMC71xxx-06-09-xx-xx-005
Process connections PMC51,
 Installation height, see table below.
1
2
3
4
5
Thread ISO 228 G 1 1/2 A;
Material version GVJ: AISI 316L; weight: 0.63 kg(1.39 lbs)
Thread ISO 228 G 2 A;
Material version GWJ: AISI 316L; weight: 0.63 kg(1.39 lbs)
Thread ANSI 1 1/2 MNPT;
Material version U7J: AISI 316L; weight: 0.63 kg(1.39 lbs)
Thread ANSI 2 MNPT;
Material version U8J: AISI 316L; weight: 0.63 kg(1.39 lbs)
Thread DIN 13 M 44x1.25;
Material version G4J: AISI 316L; weight: 0.63 kg(1.39 lbs)
Installation height H for devices with threaded connection and flush-mounted process isolating
diaphragm
Endress+Hauser
F31 housing
F15 housing
201 mm (7.91 in)
193 mm (7.6 in)
29
Cerabar M PMC51, PMP51, PMP55
EN/DIN flanges, connection dimensions as per EN 1092-1/DIN 2527
b
2
H
g2
g
k
D
P01-PMC71xxx-06-09-xx-xx-006
Process connection PMC51, EN/DIN flange with raised face (flush-mounted process isolating diaphragm)
Installation height H  ä 32.
Flange
Version
Boltholes
Material
Nominal
diameter
Nominal
pressure
Shape
1
Diameter
Thickness Raised
face
D
b
[mm]
Quantity
Diameter
Hole
circle
Flange
weight 2
g
g2
k
[mm]
[mm]
[mm]
[mm]
[kg]
CNJ
AISI 316L
DN 25
PN 10-40
B1 (D)
115
18
68
4
14
85
1.4
CPJ
AISI 316L
DN 32
PN 10-40
B1 (D)
140
18
78
4
18
100
2.0
CQJ
AISI 316L
DN 40
PN 10-40
B1 (D)
150
18
88
4
18
110
2.4
CXJ
AISI 316L
DN 50
PN 10-40
B1 (D)
165
20
102
4
18
125
3.2
DN 50
PN 10-16
B1 (D)
165
18
102
4
18
125
2.9
DN 50
PN 25-40
B1 (D)
165
20
102
4
18
125
3.2
DN 80
PN 10-40
B1 (D)
200
24
138
8
18
160
5.5
DN 80
PN 25-40
B1 (D)
200
24
138
8
18
160
5.5
CFF
PVDF
3
4
CRP
ECTFE
CZJ
AISI 316L
CSP
1)
ECTFE

Designation as per DIN 2527 in brackets
2)
Housing weight  ä 55
3)
OPL.: 15 bar (225 psi)
Process temperature range: –10 to +60 °C (+14 to +140 °F)
4)
ECTFE coating on AISI 316L. When operating in hazardous areas, avoid electrostatic charging of the plastic surfaces.
30
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
b
0.06
1.6
g2
H
ANSI flanges, connection dimensions as per ANSI B 16.5, raised face RF
g
k
D
P01-PMC71xxx-06-09-xx-xx-007
Process connection PMC51, ANSI flange with raised face RF (flush-mounted process isolating diaphragm)
Installation height H  ä 32.
Flange
Versi
on
Boltholes
Material
Nominal
diameter
Class
Diameter
Thickness
Raised face
Quantity Diameter
Hole circle
Flange
weight 1
D
b
g
g2
k
[in] / [mm]
[in] / [mm]
[kg]
[in]
[lb./sq.in]
[in] / [mm]
[in] / [mm]
[in] / [mm]
AISI 316/316L

1
150
4.25 / 108
0.56 / 14.2
2 / 50.8
4
0.62 / 15.7
3.12 / 79.2
0.9
AISI 316/316L

1
300
4.88 / 123.9
0.69 / 17.2
2 / 50.8
4
0.75 / 19
3.5 / 88.9
1.4
AISI 316/316L
2
1 1/2
150
5 / 127
0.69 / 17.5
2.88 / 73.2
4
0.62 / 15.7
3.88 / 98.6
1.0
AISI 316/316L

1 1/2
300
6.12 / 155.4
0.81 / 20.6
2.88 / 73.2
4
0.88 / 22.4
4.5 / 114.3
2.6
AFJ
AISI 316/316L

2
150
6 / 152.4
0.75 / 19.1
3.62 / 91.9
4
0.75 / 19.1
4.75 / 120.7
2.4
AFN
3
2
150
6 / 152.4
0.75 / 19.1
3.62 / 91.9
4
0.75 / 19.1
4.75 / 120.7
2.4
ACJ
ANJ
AEJ
AQJ
AFF
ECTFE
PVDF
4
2
150
6 / 152.4
0.75 /19.1
3.62 / 91.9
4
0.75 / 19.1
4.75 / 120.7
0.5
AISI 316/316L

2
300
6.5 / 165.1
0.88 / 22.4
3.62 / 91.9
8
0.75 /19.1
5 / 127
3.2
AGJ
AISI 316/316L

3
150
7.5 / 190.5
0.94 / 23.9
5 / 127
4
0.75 /19.1
6 / 152.4
4.9
AGN

3
150
7.5 / 190.5
0.94 / 23.9
5 / 127
4
0.75 /19.1
6 / 152.4
4.9
ARJ
AGF
ECTFE
PVDF

3
150
7.5 / 190.5
0.94 / 23.9
5 / 127
4
0.75 /19.1
6 / 152.4
0.9
AISI 316/316L

3
300
8.25 / 209.5
1.12 / 28.4
5 / 127
8
0.88 / 22.4
6.62 / 168.1
6.8
AHJ
AISI 316/316L

4
150
9 / 228.6
0.94 / 23.9
6.19 / 157.2
8
0.75 /19.1
7.5 / 190.5
7.1
AHN

4
150
9 / 228.6
0.94 / 23.9
6.19 / 157.2
8
0.75 /19.1
7.5 / 190.5
7.1
4
300
10 / 254
1.25 / 31.8
6.19 / 157.2
8
0.88 / 22.4
7.88 / 200.2
11.6
ASJ
ATJ
1)
ECTFE
AISI 316/316L

Housing weight  ä 55
2)
Combination of AISI 316 for required pressure resistance and AISI 316L for required chemical resistance (dual rated)
3)
ECTFE coating on AISI 316L. When operating in hazardous areas, avoid electrostatic charging of the plastic surfaces.
4)
OPL.: 15 bar (225 psi)
Process temperature range: –10 to +60 °C (+14 to +140 °F)
Endress+Hauser
31
Cerabar M PMC51, PMP51, PMP55
JIS flanges, connection dimensions as per JIS B 2220 BL, raised face RF
H
b
2
g2
g
k
D
P01-PMC71xxx-06-09-xx-xx-008
Process connection PMC51, JIS flange with raised face RF (flush-mounted process isolating diaphragm), material: AISI
316L  Installation height H, see table below.
Flange
Version
Nominal
diameter
Boltholes
Nominal
pressure
Diameter
Thickness
Raised face
D
b
[mm]
Quantity
Diameter
Hole circle
Flange
weight 1
g
g2
k
[mm]
[mm]
[mm]
[mm]
[kg]
KFJ
50 A
10 K
155
16
96
4
19
120
2.0
KGJ
80 A
10 K
185
18
127
8
19
150
3.3
KHJ
100 A
10 K
210
18
151
8
19
175
4.4
1)
Housing weight, see  ä 55
Installation height H for devices with flange
32
F31 housing
F15 housing
201 mm (7.91 in)
193 mm (7.6 in)
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Thread, internal process isolating diaphragm
➁ G 1/2A
G 1/2A
➂ G 1/2A
G 1/4
H
17
13
17
20
20
ø11.4
ø17.5
G 1/4
3
3
ø11.4
ø3.2
ø6
11.4
H
H
➀
G 1/2 A
ø17.5
ø17.5
20
Process connections PMP51
(with metal process isolating
diaphragm)
G 1/2 A
G 1/2 A
P01-PMP71xxx-06-09-xx-xx-000
Process connections PMP51, thread ISO 228
Installation height H  ä 33.
H
7
ø11.4
ø21.4
➂ 1/2 FNPT
H
➁ 1/2 MNPT
25
15
ø21.4
1/4 NPT
1/2 NPT
ø11.4
1/2 NPT
20
1/4 FNPT
H
➀ 1/2 MNPT
10
3
8
2
Thread ISO 228 G 1/2 A EN 837;
Material version GCJ: AISI 316L, version GCC: Alloy C276; weight: 0.6 kg(1.32 lbs)
Thread ISO 228 G 1/2 A G 1/4 (female);
Material version GLJ: AISI 316L, version GLC: Alloy C276; weight: 0.6 kg(1.32 lbs)
Thread ISO 228 G 1/2 A hole 11.4 mm (0.45 in);
Material version GMJ: AISI 316L, version GMC: Alloy C276; weight: 0.6 kg (1.32 lbs)
25
1
1/2 NPT
ø38
P01-PMP51xxx-06-09-xx-xx-001
Process connections PMP51, thread ANSI
Installation height H  ä 33.
1
2
3
Thread ANSI 1/2 MNPT 1/4 FNPT;
Material version RLJ: AISI 316L, version RLC: Alloy C276; weight: 0.6 kg(1.32 lbs)
Thread ANSI 1/2 MNPT hole: 400 bar (6000 psi) = 11.4 mm (0.45 in)
Material version RKJ: AISI 316L, version RKC: Alloy C276; weight: 0.6 kg(1.32 lbs)
Thread ANSI 1/2 FNPT;
Material version R1J: AISI 316L, version R1C: Alloy C276/2.4819; Weight: 0.7 kg(1.54 lbs)
Installation height H for devices with threaded connection and internal process isolating diaphragm
Height H
Endress+Hauser
F31 housing
F15 housing
169 mm (6.65 in)
150 mm (5.91 in)
33
Cerabar M PMC51, PMP51, PMP55
Thread, flush-mounted process isolating diaphragm
➁ G 1A
H
G 1/2A
18
3
3.5
ø30
2
2
14
dM = ø17.5
dM = ø28
ø30
G 1A
ø36
ø39
G 1/2A
ø23.6
ø26.5
➃
G 1 1/2A
q M 20x1.5
G 2A
2
dM = ø28
dM = ø28
ø36
G 1 1/2A
ø55
ø56.3
G2A
ø68
H
14
dM = ø17.5
2
2
1
26 8
ø17.7
3
3.5
H
H
➂
31
ø18.4
3
3.5
H
➀
M20x1.5
ø23.6
ø26.5
P01-PMx5xxxx-06-xx-xx-xx-001-package1
Thread ISO 228
Installation height H  ä 35.
1
2
3
4
5
Thread ISO 228 G 1/2 A DIN 3852 (viton seal included);
Material version GRJ: AISI 316L, version GRC: : Alloy C276; weight: 0.4 kg (0.88 lbs)
Thread ISO 228 G 1 A (viton seal included);
Material version GTJ: AISI 316L; weight: 0.7 kg (1.54 lbs)
Thread ISO 228 G 1 1/2 A
Material version GVJ: AISI 316L; weight: 1.1 kg (2.43 lbs)
Thread ISO 228 G 2 A
Material version GWJ: AISI 316L; weight: 1.5 kg (3.31 lbs)
Thread DIN13 M20x1.5
Material version G1J: AISI 316L; weight 0.4 kg (0.88 lbs)
– Welded neck
Order number: 52002643
AF 27
Viton seal
13
21
21
G½
G½
ø26
ø50
O-Ring 14 x 1.78
Viton or NBR
max. pressure resistance
100 bar
P01-PMx5xxxx-06-xx-xx-en-003
Version G0J: Thread ISO 228 G1/2; weight: 0.4 kg (0.88 lbs)
34
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
n
1 MNPT
o
1 1/2 MNPT
2 MNPT
dM = ø28
1 NPT
33.5
23
27
H
H
H
m
dM = ø28
1 1/2 NPT
dM = ø28
2 NPT
P01-PMx5xxxx-06-xx-xx-xx-002-package1
Process connections PMP51 thread ANSI
Installation height H see following table.
1
2
3
Thread ANSI 1 MNPT;
Material version U5J: AISI 316L; weight: 0.7 kg (1.54 lbs)
Thread ANSI 1 1/2 MNPT;
Material version U7J: AISI 316L; weight: 1.0 kg (2.21 lbs)
Thread ANSI 2 MNPT
Material version U8J: AISI 316L; weight: 1.3 kg (2.87 lbs)
Installation height H for devices with threaded connection and flush-mounted process isolating
diaphragm
Endress+Hauser
Description
F31 housing
F15 housing
G 1/2
163 mm (6.42 in)
148 mm (5.83 in)
G1
167 mm (6.57 in)
152 mm (5.98 in)
G 1 1/2 A
163 mm (6.42 in)
148 mm (5.83 in)
G2A
162 mm (6.38 in)
147 mm (5.79 in)
1 MNPT
162 mm (6.38 in)
147 mm (5.79 in)
1 1/2 MNPT
169 mm (6.65 in)
150 mm (5.91 in)
2 MNPT
199 mm (7.83 in)
144 mm (5.67 in)
M 20x1.5
163 mm (6.42 in)
148 mm (5.83 in)
35
Cerabar M PMC51, PMP51, PMP55
h
H
EN/DIN flanges, connection dimensions as per EN 1092-1/DIN 2527
b
2
g2
dM = ø28
60
g
k
D
(m)
P01-PMP71xxx-06-09-xx-xx-008
Process connection PMP51, EN/DIN flange with raised face, material AISI 316L
H: device height = height of device without flange h + flange thickness b
Height H  ä 37.
Flange 1
Version
CNJ
CPJ
Nominal
diameter
DN 25
DN 32
Boltholes
Nominal
pressure
PN 10-40
PN 10-40
Shape
B1 (D)
B1 (D)
2
Diameter
Hole circle Flange
weight 3
(m)
g2
k
[mm]
[mm]
[mm]
[kg]
Diameter
Thickness Raised
face
Width of
the raised
face
D
b
g
[mm]
[mm]
[mm]
115
140
18
18
Quantity
68
4
4
4
14
85
1.2
78

8.5
4
18
100
1.9

-
4
18
110
2.2
CQJ
DN 40
PN 10-40
B1 (D)
150
18
88
CXJ
DN 50
PN 25/40
B1 (D)
165
20
102
-
4
18
125
3.0
CZJ
DN 80
PN 10-40
B1 (D)
200
24
138
-
8
18
160
5.5
1)
The roughness of the surface in contact with the medium is Ra 0.8 μm (31.5 μin). Lower surface roughness available on request.
2)
Designation as per DIN 2527 in brackets
3)
Housing weight  ä 55
4)
With these process connections the sealing surface is smaller than described in the standard. Due to a smaller sealing surface a special seal must be used.
Contact a seal manufacturer or your local Endress+Hauser Sales Center.
36
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
b
2
g2
h
H
ANSI flanges, connection dimensions as per ANSI B 16.5, raised face RF
dM = ø28
60
g
k
D
(m)
P01-PMP71xxx-06-09-xx-xx-009
Process connection PMP51, ANSI flange with raised face RF (see table below)
H: device height = height of device without flange h + flange thickness b. For height H  ä 37.
Flange 1
Version
Material
Boltholes
Diameter
Thickness Diameter of
raised face
Width of Quanthe raised tity
face
Diameter
Hole circle
D
b
g
(m)
g2
k
[in] / [mm]
[in] / [mm]
[in] / [mm]
[in] / [mm]
[in] / [mm]
[in] / [mm]
[kg]
300 lb./sq.in
4.88 / 124
0.69 / 17.5 2.76 4 / 50.8
0.2 /5
4
0.75 /19.1 3.5 / 88.9
1.3
Nominal Class/
Nominal
diapressure
meter
[in]
Flange
weight 2
ANSI flanges
ANJ
AISI 316/316L3
AEJ
AISI 316/316L  1 1/2
150 lb./sq.in
5 / 127
0.69 / 17.5 2.88  / 73.2
0.52 /6.6
4
0.62 / 15.7 3.88 / 98.6
1.5
AQJ
AISI 316/316L  1 1/2
300 lb./sq.in
6.12 / 155.4
0.81 / 20.6 2.88 / 73.2
0.52 /6.6
4
0.88 / 22.4 4.5 /114.3
2.6
AFJ
AISI 316/316L  2
150 lb./sq.in
6 / 152.4
0.75 /19.1 3.62 / 91.9
-
4
0.75 /19.1 4.75 / 120.7 2.4
ARJ
AISI 316/316L  2
300 lb./sq.in
7.5 / 190.5
0.88 / 22.3 3.62 / 91.9
-
8
0.75 /19.1 5 / 127
3.2
AGJ
AISI 316/316L  3
150 lb./sq.in
7.5 / 190.5
0.94 / 23.9 5 / 127
-
4
0.75 /19.1 6 / 152.4
4.9
ASJ
AISI 316/316L  3
300 lb./sq.in
8.25 / 209.5
1.12 / 28.4 5 / 127
-
8
0.88 / 22.4 6.62 / 168.1 6.7
AHJ
AISI 316/316L  4
150 lb./sq.in
9 / 228.6
0.94 / 23.9 6.19 / 157.2
-
8
0.75 /19.1 7.5 / 190.5
ATJ
AISI 316/316L  4
300 lb./sq.in
10 / 254
1.25 / 31.8 6.19 / 157.2
-
8
0.88 / 22.4 7.88 / 200.2 11.6
1
7.1
1)
The roughness of the surface in contact with the medium is Ra 0.8 μm (31.5 μin). Lower surface roughness available on request.
2)
Housing weight  ä 55
3)
Combination of AISI 316 for required pressure resistance and AISI 316L for required chemical resistance (dual rated)
4)
With these process connections the sealing surface is smaller than described in the standard. Due to a smaller sealing surface a special seal must be used.
Contact a seal manufacturer or your local Endress+Hauser Sales Center.
Height H for devices with flange
Height H
Endress+Hauser
F31 housing
F15 housing
165 mm (6.5 in)
150 mm (5.91 in)
37
Cerabar M PMC51, PMP51, PMP55
Prepared for diaphragm seal mount
h
➀ ➁ ➂
5
ø2.5
ø7.95
P01-PMP71xxx-06-09-xx-xx-013
Version XSJ: prepared for diaphragm seal mount
1
2
3
Hole for fill fluid
Bearing
Setscrew with a hexagonal recess 4 mm (0.16 in)
Height H
F31 housing
F15 housing
190 mm (7.48 in)
175 mm (6.89 in)
PMP55 basic device
h
➀
➁
P01-PMP75xxx-06-09-xx-xx-012
PMP55 basic device with diaphragm seal
1
2
PMP55 basic device
Diaphragm seal, here e.g. flange diaphragm seal
Height H
38
F31 housing
F15 housing
190 mm (7.48 in)
175 mm (6.89 in)
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Process connections PMP55
(with metal process isolating
diaphragm)
Note!
• Information on the temperature coefficients "TK process" and "TK ambient" is listed in the following tables.
These are typical values. The temperature coefficients apply to silicone oil and the material of the process
isolating diaphragm AISI 316L/1.4435. For other filling oils, these temperature coefficients have to be
multiplied by the TK correction factor of the filling oil. For the TK correction factors, see  ä 62,
"Diaphragm seal filling oils" section.
• With regard to the temperature coefficient "TK ambient", devices with a temperature isolator behave like
devices with the same process connection with 0.1 m (0.3 ft) capillary.
• In addition, the temperature coefficient "TK ambient" is listed in relation to the capillary length for the
diaphragm seal versions which can be supplied with capillaries as standard. This information is found on
 ä 62 ff, "Influence of the temperature on the zero point" section.
• The weights of the diaphragm seals are given in the tables. See  ä 55 for the weight of the housing.
• The following drawings are schematic diagrams. In other words, the dimensions of a diaphragm seal supplied
may deviate from the dimensions given in this document.
Thread, flush-mounted process isolating diaphragm
SW
AF
x1
x1
h
h
SW
AF
dM
d1
dM
NPT
d2
G
d2
P01-PMP75xxx-06-09-xx-xx-003
Process connections PMP55, left: thread ISO 228, right: thread ANSI
Threaded connection
Version
Material
Diaphragm seal
Thread
DiaNomimeter
nal
pressure
Diameter
Screw-in
length
Across
flats
Max. dia- TK
TK
TK
phragm
ambient ambient process
diameter < 40 bar  40 bar
Height Diaphragm
seal
weight
PN
d1
d2
x1
SW/AF
dM
h
[mm]
[mm]
[mm]
[mm]
[mbar/10 K]
[mm]
[kg]
GTJ
G1
400
30
39
211
GVJ
G1 1/2 A
400
44
55
30
50
42
+ 5.4
+ 8.18
+ 3.50
20
0.9
G2
400
56
68
30
65
50
+ 1.76
+ 2.68
+ 1.60
20
1.9
U5J
1 MNPT
400
-
48
28
41
24
+ 15.66
+ 24.42
+ 8.50
37
0.6
U7J
1 1/2 MNPT
400
-
52
30
46
36
+ 8.14
+ 12.39
+ 3.90
20
0.9
U8J
2 MNPT
400
-
78
30
65
38
+ 5.4
+ 8.18
+ 2.59
35
1.8
GWJ
41
30
+ 16.03
+ 24.33
+ 4.70
19
0.4
316L
1)
28 mm (1.1 in) in conjunction with high-temperature oil
Note!
When using high-temperature oils the design can deviate significantly.
For further information please contact your local Endress+Hauser Sales Center.
Endress+Hauser
39
Cerabar M PMC51, PMP51, PMP55
D
d2
h
Pipe diaphragm seal (RDM) as per ISO2852
L
P01-FMD78xxx-06-09-xx-xx-001
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Version
Nominal
diameter
ISO 2852
Nominal
diameter
Diameter Diameter Height
Face-toface
length
D
d2
h
L
[in]
[mm]
[mm]
[mm]
TK
ambient
< 40 bar
TK
ambient
 40 bar
TK
process
Tmax
process 1)
[mbar/10 K]
Diaphragm
seal weight
[kg]
SBJ
DN 25
1"
22,5
50,5
67
126
+7,75
+8,69
+4,49
---
1,7
SCJ
DN 38
1 1/2"
35,5
50,5
67
126
+5,17
+5,69
+3,46
---
1,0
SDJ
DN 51
2"
48,6
64
79
100
+3,56
+3,91
+2,69
---
1,7
SIJ
DN 10
3/4"
---
---
---
---
---
---
---
---
---
SJJ
DN 16
3/4"
---
---
---
---
---
---
---
---
---
1)
40
Specification of the maximum process temperature at maximum ambient temperature
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
D
G
h
Pipe diaphragm seal (RDM) as per DIN 11851, Threaded adapter
L
P01-PMP55xxx-06-xx-xx-xx-000
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Version
Nominal
diameter
DIN11851
Nominal
pressure
Diameter Thread
Height Face-toface
length
D
G
h
L
[in]
[mm]
[mm]
[mm]
TK
ambient
< 40 bar
TK
ambient
 40 bar
TK
process
Tmax
process 1)
[mbar/10 K]
Diaphragm
seal weight
[kg]
SSJ
DN 25
PN40
26
Rd 52 x 1/6
65
114
2,5
3,8
11
70
1,0
STJ
DN 32
PN40
32
Rd 58 x 1/6
68
126
1,1
1,3
3,8
160
1,3
SUJ
DN 40
PN40
38
Rd 65 x 1/6
75
146
0,6
0,8
2,8
230
1,9
SZJ
DN 50
PN25
50
Rd 78 x 1/6
78
156
0,3
0,4
1,7
240
2,8
1)
Specification of the maximum process temperature at maximum ambient temperature
Endress+Hauser
41
Cerabar M PMC51, PMP51, PMP55
G
d
Pipe diaphragm seal (RDM) as per DIN11864-1
L
P01-PMx5xxxx-06-xx-xx-xx-022
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Version
Nominal
Nominal
pressure
diameter
DIN11864-1
Diameter
Thread
Face-toface
length
d
G
L
[in]
[mm]
[mm]
TK
ambient
< 40 bar
TK
ambient
 40 bar
TK
process
Tmax
process 1)
[mbar/10 K]
Diaphragm
seal weight
[kg]
VAJ
DN 25
PN40
26
Rd 52 x 1/6
128
2,5
3,8
11
70
1,3
VCJ
DN 40
PN40
38
Rd 65 x 1/6
160
0,6
0,8
2,8
230
2,0
VDJ
DN 50
PN25
50
Rd 78 x 1/6
170
0,3
0,4
1,7
240
3,0
1)
Specification of the maximum process temperature at maximum ambient temperature
30
20
Aseptic pipe fitting, DIN 11864-1 Form A; pipe DIN 11866-1
dM
d
G
P01-PMP55xxx-06-xx-xx-xx-001
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Threaded adapter
Version
Nominal
diameter
Nominal
pressure
Diaphragm seal
Diameter
Thread
max.
Diaphragm
diameter
d
G
dM
[mm]
NCJ
DN 40
TK
ambient
40 bar
[mm]
TK
ambient
 40 bar
TK process
[mbar/10 K]
Diaphragm
seal weight
[kg]
55
Rd 65 x 1/6
35
+8,18
+12,39
+2,59
+1,5
67
Rd 78 x 1/6
45
+5,4
+8,18
+1,76
+2,3
PN 16
NDJ
42
DN 50
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
30
10
Aseptic flange connection, DIN 11864-2 Form A; pipe DIN 11866-1
dM
d
K
D
P01-PMP55xxx-06-xx-xx-xx-002
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Collar flange
Version
Nominal
diameter
NFJ
DN 32
NXJ
DN 40
NZJ
DN 50
Diaphragm seal
Nominal
pressure
PN 16
TK
ambient
40 bar
TK
ambient
 40 bar
TK process
Hole circle
diameter
Seal
diameter
Outer
diameter
max.
Diaphragm
diameter
K
d
D
dM
[mm]
[mm]
[mm]
[mm]
59
47,7
76
25
+16,03
+24,33
+5,17
+1,5
65
53,7
82
35
+8,18
+12,39
+2,59
+1,7
77
65,7
94
45
+5,4
+8,18
+1,76
+2,2
[mbar/10 K]
Diaphragm
seal weight
[kg]
h
Tri-Clamp ISO 2852
dM
C7
P01-FMD78xxx-06-09-xx-xx-005
Process connection PMP55, material: AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Version
TCJ
Nominal
diameter
ISO 2852
Nominal
diameter
DIN 32676
Diameter
max.
Diaphragm
diameter
Height
C7
dM
h
[in]
[mm]
[mm]
[mm]
[mbar/10 K]
Nominal
diameter
TK
Ambient
< 40 bar
TK
Ambient
40 bar
TK
Process
Diaphragm
seal weight
[kg]
DN 25
DN 25
1
50.5
24
37
+15.33
+24.0
+4.25
0.32
DN 38
DN 40
1 1/2
50.5
34
30
+8.14
+12.39
+1.91
1.0
TDJ 1
DN 51
DN 50
2
64
48
30
+3.45
+4.81
+1.25
1.1
TFJ
DN 76.1
–
3
91
73
30
+0.3
+0.35
+0.18
1.2
TJJ
1)
1
Diaphragm seal versions optionally in conformity with ASME-BPE for use in biochemical processes, wetted surfaces Ra 0.38 m (15 in), electropolished; to
be ordered using feature 570 "Service", version "HK" in the order code
Endress+Hauser
43
Cerabar M PMC51, PMP51, PMP55
H
30
Varivent N for pipes
dM max.
D
P01-PMx5xxxx-06-xx-xx-xx-019
Process connection PMP55, material AISI 316, 3A, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Version
Description
Nominal
pressure
[bar]
TQJ
Typ F for tubes
DN 25 - DN 32
TRJ 1
Typ N for tubes
DN 40 - DN 162
1)
TK
Ambient
< 40 bar
TK
Ambient
40 bar
TK Process
Diameter
Max.
diaphragm
diameter
D
dM
[mm]
[mm]
50
30
+7.75
+11.6
+4.49
68
64
+2.26
+3.11
+1.1
Diaphragm
Max.
installation seal weight
height
H
[mbar/10 K]
[mm]
[kg]
0.6
PN 40
250
0.8
Diaphragm seal versions optionally in conformity with ASME-BPE for use in biochemical processes, wetted surfaces Ra  0.38 m (15 in), electropolished; to
be ordered using feature 570 "Service", version "HK" in the order code
23.6
41
DRD DN50 (65 mm)
dM max. =50
ø65–1.2
4 x ø11.5
ø84
ø105
P01-FM78xxx-06-09-xx-xx-002
Process connection PMP55, surface roughness of the surfaces in contact with the medium Ra  0.8 m (31.5 in) as
standard. Lower surface roughness, see feature 570 "Service" version HK.
Version
Material
Nominal
pressure
TK
Ambient
< 40 bar
TK
Ambient
 40 bar
TK Process
[mbar/10 K]
TIJ
44
AISI 316L
PN 25
+2.26
+3.11
Diaphragm
seal weight
[kg]
+1.65
0.75
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
f
m
h
SMS nozzles with coupling nut
dM
G
D
P01-PMP75xxx-06-09-xx-xx-009
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Version Nominal
diameter
Adapter
height
Thread
Height
Height
max. dia- TK
phragm
Ambient
diameter < 40 bar
D
f
G
m
h
dM
[mm]
[mm]
[mm]
Nominal Diapressure meter
TK
Ambient
 40 bar
TK
Process
[mbar/10 K]
Weight
diaphragm
seal
[inch]
[bar]
[mm]
[mm]
[kg]
T6J
1
PN 25
54
3.5
Rd 40 – 1/6
20
42.5
24
+15.66
+24.22
+7.25
0.25
T7J
1 1/2
PN 25
74
4
Rd 60 – 1/6
25
57
36
+8.18
+12.39
+2.59
0.65
TXJ
2
PN 25
84
4
Rd 70 – 1/6
26
62
48
+5.4
+8.18
+1.10
1.05
f
m
h
APV-RJT nozzles with coupling nut
dM
G
D
P01-PMP75xxx-06-09-xx-xx-010
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Nominal
pressure
Diameter
Adapter
height
Thread
Height
Height
TK
max.
diaphragm Ambient
diameter
< 40 bar
PN
D
f
G
m
h
dM
[inch]
[bar]
[mm]
[mm]
[mm]
[mm]
[mm]
TQJ
1
PN 40
77
6.5
1 13/16 – 1/8" 22
42.6
21
+15.66
+24.42
+4.21
0.45
T1J
1 1/2
PN 40
72
6.4
2 5/16 – 1/8"
22
42.6
28
+8.18
+12.39
+2.59
0.75
T2J
2
PN 40
86
6.4
2 7/8 – 1/8"
22
42.6
38
+5.4
+8.18
+1.76
1.2
Version
Nominal diameter
Endress+Hauser
TK
Ambient
 40 bar
TK
Process
[mbar/10 K]
Weight
diaphragm
seal
[kg]
45
Cerabar M PMC51, PMP51, PMP55
m
f
h
APV-ISS nozzles with coupling nut
SW/AF
dM
G
D
P01-PMP75xxx-06-09-xx-xx-011
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Version Nomi- Nominal dia- nal
meter pressure
Diameter
Adapter
height
Thread
Height Across
flat
TK
Height max.
diaphragm Ambient
seal
< 40 bar
D
f
G
m
h
dM
[mm]
[mm]
AF
[mm]
TK
Ambient
40 bar
TK
Process
[mbar/10 K]
Weight
Diaphragm
seal
[inch]
[bar]
[mm]
[mm]
[kg]
T3J
1
PN 40
54.1
4
1 1/2" – 1/8"
30
46.8
50
24
+15.66
+24.42
+4.21
0.4
T4J
1 1/2
PN 40
72
4
2" – 1/8"
30
62
50
34
+8.14
+12.39
+2.59
0.6
T5J
2
PN 40
89
4
2 1/2" – 1/8"
30
77
50
45
+5.4
+8.18
+1.76
1.1
m
f
30
H
Taper adapter with coupling nut, DIN 11851
dM
D
G
P01-PMx5xxxx-06-xx-xx-xx-020
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Taper adapter
Version Nominal
diameter
Slotted nut
Nominal Diameter Adapter
pressure
height
D
f
[mm]
[mm]
Diaphragm seal
Thread
Height
TK
max.
Diaphragm Ambient
diameter
< 40 bar
G
m
dM
[mm]
[mm]
TK
TK
Diaphragm
Max.
Ambient Process installation seal
weight
40 bar
height
H
[mbar/10 K]
[mm]
[kg]
MIJ
DN 32
PN 25
50
10
Rd 58 x 1/6"
21
32
+8.14
+12.2
+2.59
1.9
MZJ
DN 40
PN 25
56
10
Rd 65 x 1/6"
21
38
+5.4
+8.1
+1.76
2.0
MRJ
DN 50
PN 25
68.5
11
Rd 78 x 1/6"
22
52
+2.21
+3.02
+1.40
MSJ
DN 65
PN 25
86
12
Rd 95 x 1/6"
35
66
+1.6
+2.1
+0.60
2.0
MTJ
DN 80
PN 25
100
12
Rd 110 x 1/4" 30
81
+0.66
+0.81
+0.40
2.55
46
250
1.1
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
h
Threaded adapter, DIN 11851
dM
d1
G
P01-FMD78xxx-06-09-xx-xx-008
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Threaded adapter
Version
Nominal
diameter
Diaphragm seal
Nominal
pressure
Diameter
Thread
Height
max.
Diaphragm
diameter
d1
G
h
dM
[mm]
[mm]
[mm]
TK
Ambient
< 40 bar
TK
Ambient
 40 bar
TK Process
[mbar/10 K]
Diaphragm
seal weight
[kg]
NKJ
DN 50
PN 25
54
Rd 78 x 1/6"
35
52
+2.21
+3.02
+0.88
0.9
NLJ
DN 65
PN 25
71
Rd 95 x 1/6"
40
66
+1.6
+2.1
+0.60
1.7
NMJ
DN 80
PN 25
85
Rd 110 x 1/4" 40
81
+0.66
+0.81
+0.40
2.0
NEUMO BioControl
h
d2
d
dM max.
d3
d1
D
P01-FMD78xxx-06-09-xx-xx-008
Process connection PMP55, material AISI 316L, surface roughness of the surfaces in contact with the medium
Ra  0.8 m (31.5 in) as standard. Lower surface roughness, see feature 570 "Service" version HK.
Threaded adapter
Version
S4J
Nominal
diameter
DN 50
Endress+Hauser
Diaphragm seal
Nominal Diameter Hole
pressure
circle
PN 16
Diameter
Diameter Height
max.
Diaphragm
diameter
D
d1
d2
d3
h
dM
[mm]
[mm]
[mm]
[mm]
[mm]
[mm]
90
70
4x9
50
27
40
TK
Ambient
40 bar
TK
Ambient
 40 bar
TK Process Diaphragm
seal weigth
[mbar/10 K]
+5.4
+8.18
[kg]
+1.76
1.1
47
Cerabar M PMC51, PMP51, PMP55
EN/DIN flanges, connection dimensions as per EN 1092-1/DIN 2527 and DIN 2501-1
b
40
g2
L
f
dM
(m)
60
g
k
D
dM
g
P01-PMP75xxx-06-09-xx-xx-002
Process connection PMP55, EN/DIN flange with flush-mounted process isolating diaphragm, material AISI 316L
Flanges
Version
CNJ
Boltholes
Nomi- Nominal
nal dia- pressure
meter
DN 25
PN 10-40
Shape 1 Diame- Thick
ter
-ness
B1 (D)
Raised face
D
b
g
f
[mm]
[mm]
[mm] [mm] [mm]
115
18
66
3
3
Quan- Diatity
meter
(m)
Diaphragm seal
TK ambient
Hole Max.
circle diaphragm
40
40
diameter
bar
bar
TK
Diaprocess phragm
seal
weight
g2
k
dM
[mm]
[mm]
[mm]
4
14
85
32
+16.03 +24.33 +3.20
[mbar/10 K]
[kg]
2.1
QIJ
DN 25
PN 63-160
E
140
24
68
2
-
4
18
100
28
+16.03 +24.33 +3.20
2.5
QJJ
DN 25
PN 250
E
150
28
68
2
-
4
22
105
28
+16.03 +24.33 +5.17
3.7
QSJ
DN 25
PN 400
E
180
38
68
2
-
4
26
130
28
+16.03 +24.33 +5.17
7.0
CPJ
DN 32
PN 10-40
B1 (D)
140
18
77
2.6
8.5
4
18
100
34
+8.14
+12.39 +2.59
1.9
CQJ
DN 40
PN 10-40
B1 (D)
150
18
87
2.6
-
4
18
110
48
+5.40
+8.18
+2.15
2.2
CXJ
DN 50
PN 10-40
B1 (D)
165
20
102
3
-
4
18
125
59
+2.21
+3.02
+1.50
3.0
PDJ
DN 50
PN 63
B2 (E)
180
26
102
3
-
4
22
135
59
+2.21
+3.02
+1.00
4.6
QOJ
DN 50
PN 100-160 E
195
30
102
3
-
4
26
145
59
+2.21
+3.02
+1.00
6.2
QMJ
DN 50
PN 250
E
200
38
102
3
-
8
26
150
59
+2.21
+3.02
+1.15
7.7
QVJ
DN 50
PN 400
E
235
52
102
3
-
8
30
180
59
+2.21
+3.02
+1.15
14.7
CZJ
DN 80
PN 10-40
B1 (D)
200
24
138
3.5
-
8
18
160
89
+0.19
+0.25
+0.20
5.3
PPJ
DN 80
PN 100
B2 (E)
230
32
138
4
-
8
24
180
89
+0.19
+0.25
+0.35
8.9
PQJ
DN 100 PN 100
B2 (E)
265
36
175
5
-
8
30
210
89
+0.19
+0.25
+0.11
13.7
FDJ 2 DN 50
PN 10-40
B1 (D)
165
20
102
3
-
4
18
125
47
+3.45
+4.81
+1.67

FEJ 
PN 10-40
B1 (D)
200
24
138
3.5
-
8
18
160
72
+0.19
+0.25
+0.70

DN 80
1)
Designation as per DIN 2527 in brackets
2)
Available with 50 mm (1.97 in), 100 mm (3.94 in) or 200 mm (7.87 in) extended diaphragm seal, for extended diaphragm seal diameter and weight see the
following table
48
Version
Nominal
diameter
Nominal
pressure
Extended
diaphragm seal
length
Extended
diaphragm seal
diameter d3
Diaphragm
seal weight
[mm]
[mm]
[kg]
FDJ
DN 50
PN 10-40
50 /100 / 200
48.3
3.2 / 3.8 / 4.4
FEJ
DN 80
PN 10-40
50 /100 / 200
76
6.2 / 6.7 / 7.8
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
ANSI flanges, connection dimensions as per ANSI B 16.5, raised face RF
400 – 2500 lb/sq.in
0.25 in (6.4 mm)
dM
L
150, 300 lb/sq.in
0.06 in (1.6 mm)
b
40
g2
(m)
60
g
k
D
dM
g
P01-PMP75xxx-06-09-xx-xx-001
Process connection PMP55, ANSI flange with and without extended diaphragm seal
Flange
Versi Material
on
1
Nominal Class
diameter
Boltholes
Diaphragm seal
Quan- Diame- Hole
tity
ter
circle
TK ambient
Max.
TK
diaprocess
phragm 40 bar 40 bar
diameter
Diameter
Thickness
Raised face
D
b
g
(m)
g2
k
dM
[in]
[mm]
[in]
[mm]
[in]
[mm]
[in]
[lb./
sq.in]
[in]
[mm]
[in]
[mm]
[in]
[mm]
[in]
[mm]
[mbar/10 K]
Diaphragm
seal
weight
[kg]
ACJ
AISI 316/
316L
1
150
4.25
108
0.56
14.2
2
50.8
-
4
0.62
15.7
3.12
79.2
1.26
32
+16.03
+24.33
+3.65
1.2
ANJ
AISI 316/
316L
1
300
4.88
124
0.69
17.5
2
50.8
2
5
4
0.75
19.1
3.5
88.9
1.26
32
+16.03
+24.33
+3.65
1.3
A0J
AISI 316/
316L
1
400/
600
4.88
124
0.69
17.5
2
50.8
-
4
0.75
19.1
3.5
88.9
1.26
32
+16.03
+24.33
+5.17
1.4
A2J
AISI 316/
316L
1
900/
1500
5.88
149.4
1.12
28.4
2
50.8
-
4
1
25.4
4
101.6
1.26
32
+16.03
+24.33
+5.17
3.2
A4J
AISI 316/
316L
1
2500
6.25
158.8
1.38
35.1
2
50.8
-
4
1
25.4
4.25
108
1.26
32
+16.03
+24.33
+5.17
4.6
AEJ
AISI 316/
316L
1 1/2
150
5
127
0.69
17.5
2.88
73.2
0.52
6.6
4
0.62
15.7
3.88
96.6
1.89
48
+8.14
+12.39
+1.90
1.5
AQJ
AISI 316/
316L
1 1/2
300
6.12
155.4
0.81
20.6
2.88
73.2
0.52
6.6
4
0.88
22.4
4.5
114.3
1.89
48
+8.14
+12.39
+2.59
2.6
AFJ
AISI 316/
316L
2
150
6
152.4
0.75
19.1
3.62
91.9
-
4
0.75
19.1
4.75
120.7
2.32
59
+2.21
+3.02
+1.60
2.2
FMJ 2 AISI 316/
316L
2
150
6
152.4
0.75
19.1
3.62
91.9
-
4
0.75
19.1
4.75
120.7
1.85
47
+3.45
+4.81
+1.67

ARJ
AISI 316/
316L
2
300
6.5
165.1
0.88
22.4
3.62
91.9
-
8
0.75
19.1
5
127
2.32
59
+2.21
+3.02
+0.85
3.4
A1J
AISI 316/
316L
2
400/
600
6.5
165.1
1
25.4
3.62
91.9
-
8
0.75
19.1
5
127
2.32
59
+2.21
+3.02
+0.85
4.3
A3J
AISI 316/
316L
2
900/
1500
8.5
215.9
1.5
38.1
3.62
91.9
-
8
1
25.4
6.5
165.1
2.32
59
+2.21
+3.02
+0.75
10.3
A5J
AISI 316/
316L
2
2500
9.25
235
2
50.8
3.62
91.9
-
8
1.12
28.4
6.75
171.5
2.32
59
+2.21
+3.02
+0.75
15.8
AGJ
AISI 316/
316L
3
150
7.5
190.5
0.94
23.9
5
127
-
4
0.75
19.1
6
152.4
3.50
89
+0.19
+0.25
+0.18
5.1
ASJ
AISI 316/
316L
3
300
8.25
209.5
1.12
28.4
5
127
-
8
0.75
19.1
6
152.4
3.50
89
+0.19
+0.25
+0.11
7.0
Endress+Hauser
49
Cerabar M PMC51, PMP51, PMP55
Flange
Versi Material 1 Nominal Class
on
diameter
Boltholes
Diaphragm seal
Quan- Diame- Hole
tity
ter
circle
TK ambient
Max.
TK
diaprocess
phragm 40 bar 40 bar
diameter
Diameter
Thickness
Raised face
D
b
g
(m)
g2
k
dM
[in]
[mm]
[in]
[mm]
[in]
[mm]
[in]
[lb./
sq.in]
[in]
[mm]
[in]
[mm]
[in]
[mm]
[in]
[mm]
AISI 316/
316L
3
150
7.5
190.5
0.94
23.9
5
127
-
4
0.75
19.1
6
152.4
2.83
72
+0.19
+0.25
+0.70

FWJ  AISI 316/
316L
3
300
8.25
209.5
1.12
28.4
5
127
-
8
0.88
22.4
6.62
168.1
2.83
72
+0.19
+0.25
+0.70

AHJ
AISI 316/
316L
4
150
9
228.6
0.94
23.9
6.19 157.2
8
0.75
19.1
7.5
190.5
3.50
89
+0.19
+0.25
+0.33
7.2
ATJ
AISI 316/
316L
4
300
10
254
1.25
31.8
6.19 157.2
8
0.88
22.4
7.88
200.2
3.50
89
+0.19
+0.25
+0.11
11.7
FOJ 
AISI 316/
316L
4
150
9
228.6
0.94
23.9
6.19 157.2
8
0.75
19.1
7.5
190.5
3.50
89
+0.19
+0.25
+0.11

FXJ 
AISI 316/
316L
4
300
10
254
1.25
31.8
6.19 157.2
8
0.88
22.4
7.88
200.2
3.50
89
+0.19
+0.25
+0.11

FNJ 
[mbar/10 K]
Diaphragm
seal
weight
[kg]
1)
Combination of AISI 316 for required pressure resistance and AISI 316L for required chemical resistance (dual rated)
2)
Available with 2 in, 4 in, 6 in or 8 in extended diaphragm seal, for extended diaphragm seal diameter and weight see the following table
Nominal
diameter
Class
Extended
diaphragm seal
length (L)
Extended
diaphragm seal
diameter d3
Diaphragm
seal weight
[in]
[lb./sq.in]
[in] [(mm)]
[in] [(mm)]
[kg]
FMJ
2
150
–
–
–
–
2 (50.8)
4 (101.6)
6 (152.4)
8 (203.2)
1.9 (48.3)
–
–
–
–
3.0
3.4
3.9
4.4
FNJ
3
150
–
–
–
–
2 (50.8)
4 (101.6)
6 (152.4)
8 (203.2)
2.99 (75.9)
–
–
–
–
6.0
6.6
7.1
7.8
FWJ
3
300
–
–
–
–
2 (50.8)
4 (101.6)
6 (152.4)
8 (203.2)
2.99 (75.9)
–
–
–
–
7.9
8.5
9.0
9.6
FOJ
4
150
–
–
–
–
2 (50.8)
4 (101.6)
6 (152.4)
8 (203.2)
3.7 (94)
–
–
–
–
8.6
9.9
11.2
12.4
FXJ
4
300
–
–
–
–
2 (50.8)
4 (101.6)
6 (152.4)
8 (203.2)
3.7 (94)
–
–
–
–
13.1
14.4
15.7
16.9
Version
50
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
JIS flanges, connection dimensions as per JIS B 2220 BL, raised face RF
b
40
g2
f
dM
g
k
D
P01-PMP75xxx-06-09-xx-xx-000
Process connection PMP55, JIS flange with raised face RF, material AISI 316L
Flange
Versi
on
Nominal diameter
Boltholes
Diameter
Hole
circle
TK ambient
Max.
TK
diaprocess
phragm
40 bar  40 bar
diameter
f
g2
k
dM
[mm]
[mm]
[mm]
[mm]
[mm]
Thickness
Diameter
of
raised
face
Height
of
raised
face
D
b
g
[mm]
[mm]
DiaNomimeter
nal
pressure
Diaphragm seal
Quantity
[mbar/10 K]
Diaphragm
seal
weight1
[kg]
KCJ
25 A
10 K
125
14
67
1
4
19
90
32
+16.03
+24.33
+5.17
1.5
KEJ
40 A
10 K
140
16
81
2
4
19
105
48
+5.40
+8.18
+2.15
2.0
KFJ
50 A
10 K
155
16
96
2
4
19
120
59
+2.21
+3.02
+1.00
2.3
KGJ
80 A
10 K
185
18
127
2
8
19
150
89
+0.19
+0.25
+0.11
3.3
KHJ
100 A
10 K
210
18
151
2
8
19
175
89
+0.19
+0.25
+0.11
4.4
1)
Housing weight  ä 55
Endress+Hauser
51
Cerabar M PMC51, PMP51, PMP55
Thread 1/2 NPT and 1 NPT, separator
89
100
90
100
➀
➀
SW22
22 AF
SW22
22 AF
6
1/2 NPT
G½
P01-PMP75xxx-06-09-xx-xx-013
Process connection PMP55, left version "UDJ" threaded, with threaded connection ISO 228 G 1/2 B, right version "UEJ"
with threaded connection ANSI 1/2 MNPT
1
PTFE seal as standard max. 260°C (500°F) (higher temperatures on request)
Version
Measuring
range
Description
Nominal
pressure
TK process
Diaphragm seal weight
[mbar/10 K]
[kg]
UDJ
 40 bar
ISO 228 G 1/2 B
PN 40
+0.75
1.43
UEJ
 40 bar
ANSI 1/2 MNPT
PN 40
+0.55
1.43
ø118
15
1/2 NPT
SW 27
27 AF
ø30
27
44.5
26
19
12
94.5
76
ø118
1 NPT
SW 36
36 AF
ø52
P01-PMP75xxx-06-09-xx-xx-008
Process connection PMP55, version "UGJ" and "UHJ", threaded, material AISI 316L, seal Viton
Version
Description
Nominal
pressure
TK ambient
TK process
[mbar/10 K]
52
Diaphragm
seal weight
[kg]
UGJ
1/2 NPT
PN 250
+3.45
+1.28
4.75
UHJ
1 NPT
PN 250
+3.45
+1.28
5.0
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Thread ISO 228 G 1/2 A and ANSI 1/2 MNPT, separator
ø72.6
70
70
ø72.6
21.5
20
3
17
14
SW 30
AF 30
14
SW 30
AF 30
ø18.4
ø11.4
1/2 - 14 NPT
ø4
ø6
G 1/2A
P01-PMP75xxx-06-09-xx-xx-004
Process connection PMP55, version "UBJ" and "UCJ", welded, material AISI 316L
Version
Description
Nominal
pressure
TK ambient
TK process
Diaphragm
seal weight
[mbar/10 K]
[kg]
UBJ
ISO 228 G 1/2 A
PN 160
+0.9
+0.30
1.43
UCJ
ANSI 1/2 MNPT
PN 160
+0.9
+0.30
1.43
ø115
17
SW 22
3
ø2.5
1/2 NPT
20
SW 36
19
SW 36
92.5
84
ø115
ø4
ø6
G 1/2A
P01-PMP75xxx-06-09-xx-xx-007
Process connection PMP55, version "UBJ" and "UCJ", threaded, with integrated seal lip, material AISI 316L
Version
Measuring Description
range
Nominal
pressure
TK ambient
TK process
[mbar/10 K]
Diaphragm
seal weight
[kg]
UBJ
> 40 bar
ISO 228 G 1/2 A
PN 400
+3.45
+1.28
4.75
UCJ
> 40 bar
ANSI 1/2 MNPT
PN 400
+3.45
+1.28
4.75
Note!
When using high-temperature oils the design can deviate significantly.
For further information please contact your local Endress+Hauser Sales Center.
Endress+Hauser
53
Cerabar M PMC51, PMP51, PMP55
"Separate housing" version
69
118
112
➀
➁
127
101
ø52
P01-xMx5xxxx-06-xx-xx-xx-002
F31 housing dimensions. Housing weight, see  ä 55. ➀ Cover without viewing window. ➁ Cover with viewing window.
63
118
95
➀
➁
114
101
ø52
P01-xMx5xxxx-06-xx-xx-xx-003
F15 housing dimensions. Housing weight, see  ä 55. ➀ Cover without viewing window. ➁ Cover with viewing window.
Reduction in installation height
If the separate housing is used, the mounting height of the process connection is reduced compared to the
dimensions of the standard version (see graphic).
r ³ 120 mm
r ³ 120 mm
r ³ 120 mm
F15
➀
ø54.1
➀
81
17
29
36
44
F31
➀
P01-xMx5xxxx-06-xx-xx-xx-000
1
Process connection adapter.
A minimum bending radius (r) of 120 mm (4.72 in) must be observed for the cable.
54
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Weight
Housing
F31 (aluminum)
F15 (stainless steel) Separate housing
With electronic insert and
local display
1.1 kg (2.43 lbs)
0.8 kg (1.76 lbs)
With electronic insert without
local display
1.0 kg (2.21 lbs)
0.7 kg (1.54 lbs)
Weight of housing + 0.5 kg (1.10 lbs).
Weight of sensor + 0.5 kg (1.10 lbs).
Process connections
• Process connections PMC51 (with ceramic process isolating diaphragm):  ä 27 ff
• Process connections PMP51 (with metal process isolating diaphragm):  ä 33 ff
• Process connections PMP55 (with metal process isolating diaphragm):  ä 39 ff
Material
F31 housing:
• F31 housing, optionally:
– Die-cast aluminum with protective powder-coating on polyester base: RAL 5012 (blue),
cover: RAL 7035 (gray)
• Sight glass: mineral glass
• Cable gland M20 x 1.5: polyamide (PA) or CuZn nickel-plated
• Pressure compensation filter: PA6 GF10
• Cable entry blind plug:
– G ½": PBT-GF30 FR, for Dust Ex, Ex d, FM XP and CSA XP: AISI 316L (1.4435)
– NPT ½": PBT-GF30 FR, for Dust Ex, Ex d, FM XP and CSA XP: AISI 316L (1.4435)
• Seals:
– Cable gland and blind plug: EPDM
– Pressure compensation filter O-ring: silicone (VMQ)
– Cover: EPDM
– Sight glass: silicone (VMQ)
• Nameplates: plastic
F15 housing:
• Housing and cover: stainless steel AISI 316L
• Sight glass:
– Version for non-hazardous areas, ATEX Ex ia, NEPSI Zone 0/1 Ex ia, IECEx Zone 0/1 Ex ia, FM NI, FM
IS, CSA IS: polycarbonate (PC)
– ATEX 1/2 D, ATEX 1/3 D, ATEX 1 GD, ATEX 1/2 GD, ATEX 3 G, FM DIP, CSA Dust Ex: mineral glass
• Cable gland M20 x 1.5: polyamide PA, for Dust-Ex: CuZn nickel-plated
• Pressure compensation filter: PA6 GF10
• Blind plug: PBT-GF30 FR, for Dust Ex: AISI 316L
• Seals:
– Cable gland and blind plug: NBR
– Pressure compensation filter O-ring: silicone (VMQ)
– Cover: silicone with PTFE coating
– Sight glass: silicone (VMQ)
• Nameplates: lasered
Process connections
• "Threaded connection" and "DIN/EN flanges" (see also "Ordering information" section): stainless steel AISI
316L
Cable for separate housing:
• PE cable:
Abrasion-proof cable with strain-relief Dynema members; shielded using aluminum-coated foil; insulated
with polyethylene (PE-LD), black; copper wires, twisted, UV-resistant
• FEP cable:
Abrasion-proof cable; shielded using galvanized steel wire mesh; insulated with fluorinated ethylene
propylene (FEP), black; copper wires, twisted, UV-resistant
Endress+Hauser
55
Cerabar M PMC51, PMP51, PMP55
TSE Certificate of Suitability
The following applies to all process wetted device components:
• They do not contain any materials derived from animals.
• No auxiliaries or operating materials derived from animals are used in production or processing.
Note!
The wetted device components are listed in the "Mechanical construction" ( ä 27) and "Ordering
information" ( ä 69 ff) sections.
Miscellaneous:
• Process isolating diaphragm PMC51: Al2O3 aluminum-oxide ceramic, Ceraphire® (FDA 21CFR186.1256,
USP
Class VI), ultrapure 99.9 % ( see also www.endress.com/ceraphire)
• Mounting accessories: mounting kit with screws AISI 304
• Capillary: AISI 316 Ti
• Protective hose for capillary: AISI 304
For process connections, process isolating diaphragms, seals and filling oils see ordering information,
 ä 69 ff.
56
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Human interface
Operating elements
Local display (optional) for devices with HART electronics
A 4-line liquid crystal display (LCD) is used for display and operation. The local display shows measured values,
dialog texts as well as fault and notice messages in plain text, thereby supporting the user at every stage of
operation. The liquid crystal display of the device can be turned in 90° stages.
Depending on the orientation of the device, this makes it easy to operate the device and read the measured
values.
Functions:
• 8-digit measured value display including sign and decimal point, bar graph for 4 to 20 mA HART as current
display
• Three keys for operation
• Simple and complete menu guidance as parameters are split into several levels and groups
• Each parameter is given a 3-digit ID number for easy navigation
• Possibility of configuring the display to suit individual requirements and preferences, such as language,
alternating display, contrast setting, display of other measured values such as sensor temperature etc.
• Comprehensive diagnostic functions (fault and warning message etc.)
Measured value display
Device tag
–
+
Value
Header line
Symbol
Main line
Information
line
Unit
E
Bargraph
Operating menu
Operating keys
Parameter with selection list
Direct
Access
Code
Selection
options
Freely editable parameter
Value that
can be
edited
P01-Mxxxxxxx-07-xx-xx-en-002
Endress+Hauser
57
Cerabar M PMC51, PMP51, PMP55
Local display (optional) for devices with analog electronics
A 4-line liquid crystal display (LCD) is used. The local display shows measured values, fault messages and notice
messages. The device display can be rotated in 90 ° stages.
Depending on the orientation of the device, this makes it easy to read the measured values.
Functions:
• 8-digit measured value display including sign and decimal point, bar graph for 4 to 20 mA as
current display.
• Diagnostic functions (fault and warning message etc.)
Measured value display
Value
F
F
Main line
Information
line
Symbol
Unit
Bargraph
P01-Mxxxxxxx-07-xx-xx-de-002
Operating keys and elements located on the electronic insert
➅
➆
➁
Display
Zero
➄
Span
➀
on
Display
Zero
➂
Span
on
damping
R
FIELD COMMUNICATION PROTOCOL
delta p only
off
HART
SW / Ö
SW / P2=High
damping
SW / Alarm min
off
on
4
off
5
1
➃
➀ ➁➂ ➃
P01-Mxxxxxxx-19-xx-xx-xx-001
Analog electronic insert
1
1
2
3
4
5
6
7
58
P01-Mxxxxxxx-19-xx-xx-xx-010
HART electronic insert
DIP switch for locking/unlocking parameters
relevant to the measured value
DIP switch for switching damping on/off
DIP switch for alarm current SW / Alarm Min
(3.6 mA)
DIP switch only for Deltabar M
Slot for optional local display
Green LED to indicate successful operation
Operating keys for lower range value (zero) and
upper range value (span)
off
damping
3
SW / Ö
SW / P2=High
2
damping
SW / Alarm min
1
on
2
3
4
Operating keys for lower range value (zero) and
upper range value (span)
Green LED to indicate successful operation
Slot for optional local display
DIP switch for switching damping on/off
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Onsite operation
Function
Operation with operating keys and operating
elements on the electronic insert
Operation via display
Analog
HART
Analog
HART
Position adjustment (zero point
correction)
X
X
--
X
Setting lower range value and upper
range value - reference pressure
present at the device
X
X
--
X
Device reset
X
X
--
X
Locking and unlocking parameters
relevant to the measured value
--
X
--
X
Value acceptance indicated by the
green LED
X
X
--
--
Switching damping on and off
X
X
--
X
Endress+Hauser
59
Cerabar M PMC51, PMP51, PMP55
Remote operation
All software parameters are accessible depending on the position of the write protection switch on the device.
HART
Remote operation via:
• Field Communicator 375 handheld terminal. Use the handheld terminal to set all parameters all along the
bus cable via menu operation.
• Field Xpert. Field Xpert is an industrial PDA with integrated 3.5" touchscreen from Endress+Hauser based
on Windows Mobile. It communicates via wireless with the optional VIATOR Bluetooth modem connected
to a HART device point-to-point or wireless via WiFi and Endress+Hauser’s Fieldgate FXA520. Field Xpert
also works as a stand-alone device for asset management applications. For details refer to BA060S/00/en.
• FieldCare. FieldCare is an Endress+Hauser asset management tool based on FDT technology. With
FieldCare, you can configure all Endress+Hauser devices.
– FieldCare supports the following functions:
– Configuration of transmitters in offline and online mode
– Loading and saving device data (upload/download)
– Documentation of the measuring point
– Connection options:
– By means of the Commubox FXA191 for intrinsically safe HART communication with FieldCare via the
RS232C interface of a computer. For details refer to TI237F/00/en.
– By means of the Commubox FXA195 for intrinsically safe HART communication with FieldCare via the
USB port of a computer. For details refer to TI404F/00/en.
1
4...20 mA
³ 250 W
2
–
+
5
3
FieldCare
4
6
8
ENDRESS + HAUSER
RMA 422
7
9
P01-xMx5xxxx-04-xx-xx-xx-009
1
2
3
4
5
6
7
8
9
PLC
Resistor for HART communication
VIATOR Bluetooth Modem with connection cable
Field Xpert (Industrial PDA)
Screening
Commubox FXA191 (RS232), FXA195 (USB)
Handheld terminal DXR375/FC375
Transmitter power supply unit RMA422 or RN221N (with integrated communication resistor)
Conection for:
- Commubox FXA191 (RS232), FXA195 (USB)
- Handheld terminal DXR375/FC375
Note!
For further information please contact your local Endress+Hauser Sales Center.
60
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Planning instructions for diaphragm seal systems
With the Endress Hauser "Applicator" selection tool you will find the optimum diaphragm seal for your
application. Online on "www.endress.com/applicator" or offline on CD.
For further information please contact your local Endress+Hauser Sales Center.
Applications
Diaphragm seal systems should be used if the medium and the device need to be separated. Diaphragm seal
systems offer clear advantages in the following instances:
• In the case of high medium temperatures ( ä 25, "Process temperature limits" section.)
• For aggressive media
• If extreme measuring point cleaning is necessary, or in the event of very damp mounting locations
• If the measuring point is exposed to vibrations
• For mounting locations that are difficult to access
Function and design
Diaphragm seals separate the measuring system from the process medium.
A diaphragm seal system consists of:
• A diaphragm seal
• A capillary tube or a temperature isolator if necessary
• Fill fluid
• A pressure transmitter
The process pressure acts via the process isolating diaphragm of a diaphragm seal on the liquid-filled system,
which transfers the process pressure via the capillary tube onto the sensor of the pressure transmitter.
Endress+Hauser delivers all diaphragm seal systems as welded versions. The system is hermetically sealed,
which ensures greater reliability.
Note!
The correlations between the individual diaphragm seal components are presented in the following section.
For further information and comprehensive diaphragm seal system designs, please contact your local
Endress+Hauser Sales Center.
Diaphragm seal
The diaphragm seal determines the application range of the system on the basis of
• The diameter of the process isolating diaphragm
• The process isolating diaphragm: stiffness and material
• The design (oil volume)
Diameter of the process isolating diaphragm
The greater the diameter of the process isolating diaphragm (less stiff), the smaller the temperature effect on
the measurement result.
Note: To keep the temperature effect within practical limits, you should select diaphragm seals with a nominal
diameter DN 80 or 3" provided that the process connection permits this.
Stiffness of the process isolating diaphragm
The stiffness depends on the diameter of the process isolating diaphragm, the material, any existing coating,
the thickness of the process isolating diaphragm and the shape. The thickness of the process isolating diaphragm
and the shape are determined by the design. The stiffness of a process isolating diaphragm of a diaphragm seal
influences the temperature application range and the measuring error caused by temperature effects.
Capillary
Capillaries with an internal diameter of 1 mm (0.04 in) are used as standard.
As a result of its length and internal diameter, the capillary tube influences the TK zero point, the ambient
temperature application range and the response time of a diaphragm seal system.
 ä 62 ff, "Influence of the temperature on the zero point" and "Ambient temperature range" sections.
Observe the installation instructions regarding capillary tubes.  ä 67 ff, "Installation instructions" section.
Endress+Hauser
61
Cerabar M PMC51, PMP51, PMP55
Filling oil
When selecting the filling oil, the medium temperature and ambient temperature, as well as the process
pressure, are of crucial importance. Observe the temperatures and pressures during commissioning and
cleaning. A further selection criterion is the compatibility of the filling oil with the requirements of the medium.
For example, only filling oils that do not present a health hazard are used in the food industry, e.g. vegetable
oil or silicone oil.
See also the following section "Diaphragm seal filling oils".
The filling oil used influences the TK zero point, the temperature application range of a diaphragm seal system
and the response time.  ä 62 ff, "Influence of the temperature on the zero point" section.
Pressure transmitter
The pressure transmitter influences the temperature application range, the TK zero point and the response time
as a result of its volume change. The volume change is the volume that has to be shifted in order to pass through
the complete measuring range.
Pressure transmitters from Endress+Hauser are optimized with regard to minimum volume change.
Diaphragm seal filling oils
Ver
Filling oil
sion1
Permissible
temperature range 2 at
0.05 bar (0,725 psi) 
pabs  1 bar (14.5 psi)
Permissible
temperature range2
at pabs  1 bar (14.5
psi)
Density
Viscosity
TK
Note
Thermal
expansion correction
coefficient factor
[g/cm3] / [mm²/s] / [cSt]
[SGU]
at 25°C (77°F)
[1/K]
1
Silicone oil
–40 to +180°C
(–40 to +356°F)
–40 to +250°C
(–40 to +482°F)
0.96
100
0.00096
1
Suitable for foods
FDA 21 CFR 175.105
2
Inert oil
–40 to +80°C
(–40 to +176°F)
–40 to +175°C
(–40 to +347°F)
1.87
27
0.000876
0.91
For ultrapure gas and
oxygen applications
4
Vegetable oil
–10 to +120°C
(+14 to +248°F)
–10 to +200°C
(+14 to +392°F)
0.94
9.5
0.00101
1.05
suitable for foods
FDA 21 CFR 172.856
5
Hightemperature oil 3
–10 to +200°C
(+14 to +392°F)
–10 to +400°C
(+14 to +752°F)
1.07
37
0.0007
0.72
High temperatures
6
Low-temperature –70 to +80°C
oil
(–94 to +176°F)
–70 to +180°C
(–94 to +349°F)
0.92
4.4
0.00108
1.12
Low temperatures
1)
Version for feature 180 in the order code
2)
Observe temperature limits of the device ( ä 25).
3)
When simultaneously applying the diaphragms seal at high process temperatures and low absolute pressures, Endress+Hauser recommends the vacuum
service (Feature 570 "Service" version "HG").
Influence of the temperature
on the zero point
A temperature change results in a volume change in the filling oil. The volume change depends on the thermal
expansion coefficient of the filling oil and on the volume of the fill fluid at calibration temperature (constant in
the range: +21 to +33°C (+70 to 91°F)).  ä 62, "Diaphragm seal filling oils" section.
For example, the filling oil expands in the event of a temperature increase. The additional volume presses
against the process isolating diaphragm of a diaphragm seal. The stiffer a process isolating diaphragm is, the
greater its return force, which counteracts a volume change and acts together with the process pressure on the
measuring cell, thus shifting the zero point. For the temperature coefficient "TK process" and "TK ambient (for
devices with a capillary)" see  ä 39 ff, "Process connections PMP55" section.
The following diagrams display the temperature coefficient "TK ambient" as a function of the capillary length.
The following application is displayed: capillary temperature and transmitter temperature (ambient
temperature) change, the process temperature corresponds to the calibration temperature.
The temperature coefficients obtained from the diagrams apply to silicone oil and the material of the process
isolating diaphragm AISI 316L/1.4435. For other filling oils, these temperature coefficients must be multiplied
by the TK correction factor of the corresponding filling oil. For the TK correction factors, see  ä 62,
"Diaphragm seal filling oils" section.
With regard to the temperature coefficient "TK ambient", devices with a temperature isolator behave like
devices with the same process connection and 0.1 m (0.3 ft) capillary.
62
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
PN < 40 bar
TK Ambient 16
[mbar/10 K]
14
6
12
10
8.4
mbar
10 K
8
6
4
2
0
0
1
2
3
4
5
6
7
8
9
10
Capillary length
[m]
P01-PMP75xxx-05-xx-xx-xx-007
Diagram TK ambient as a function of the capillary length for PMP55, PN < 40 bar (580 psi)
Example for:
– Diaphragm seal version "CXJ, EN/DIN flange DN 50 PN 10-40 B1, AISI 316L"
– Capillary length: 5 m (16 ft)
– Ambient temperature, capillary/transmitter: 45 °C (113 °F)
– Filling oil: silicone oil
1.
Select characteristic curve type for the diaphragm seal version "CXJ" in accordance with the following
table.
Result: characteristic curve type 6
2.
Obtain value for TK ambient from the diagram.
Result: 8.4 mbar (0.1218 psi)/10 K
3.
Tambient – Tcalibration = 45°C (113°F) – 25°C (77°F) = 20°C (68°F) 8.4 mbar (0.1218 psi)/10 K x 20 K
= 16.8 mbar (0.2436 psi)
Result: In this application, the zero point is shifted by 16.8 (0.2436 psi) mbar.
Note!
• The influence of temperature on the zero point can be corrected with position adjustment.
• The temperature effect can be minimized by using a filling oil with a smaller expansion coefficient, a shorter
capillary, a diaphragm seal with a larger diameter of the process isolating diaphragm or by using a smaller
capillary internal diameter.
Endress+Hauser
63
Cerabar M PMC51, PMP51, PMP55
Curve type 1 up to 7
PN ³ 40 bar
TK Ambient 16
[mbar/10 K]
7
6
14
12
5
10
4
8
6
7
4
3
2
2
1
0
0
1
2
3
4
5
6
7
8
9
10
Capillary length
[m]
P01-PMP75xxx-05-xx-xx-xx-005
Diagram TK ambient as a function of the capillary length for PMP55, PN 40 bar (580 psi)
Characteristic
curve type
1
2
3
4
5
6
64
Version in
the order
code
CZJ
PPJ
PQJ
KGJ
KHJ
FEJ
AGJ
ASJ
AHJ
ATJ
FNJ
FWJ
FOJ
FXJ
TFJ
MTJ
NMJ
SDJ
SZJ
VDJ
SCJ
STJ
SUJ
VCJ
CXJ
PDJ
QOJ
QMJ
QVJ
AFJ
ARJ
A1J
A3J
A5J
Diaphragm seal
EN/DIN flange DN 80 PN 10-40 B1, AISI 316L
EN/DIN flange DN 80 PN 100 B2, AISI 316L
EN/DIN flange DN 100 PN 100 B2, AISI 316L
JIS flange 10K 80A RF, AISI 316L
JIS flange 10K 100A RF, AISI 316L
EN/DIN flange DN 80, PN 10-40 B1, extended diaphragm seal: 50 mm/100 mm/200 mm, AISI 316L
ANSI flange 3" 150 lbs RF, AISI 316/316L
ANSI flange 3" 300 lbs RF, AISI 316/316L
ANSI flange 4" 150 lbs RF, AISI 316/316L
ANSI flange 4" 300 lbs RF, AISI 316/316L
ANSI flange 3" 150 lbs RF, extended diaphragm seal: 2"/4"/6"/8", AISI 316/316L
ANSI flange 3" 300 lbs RF, extended diaphragm seal: 2"/4"/6"/8", AISI 316/316L
ANSI flange 4" 150 lbs RF, extended diaphragm seal: 2"/4"/6"/8", AISI 316/316L
ANSI flange 4" 300 lbs RF, extended diaphragm seal: 2"/4"/6"/8", AISI 316/316L
Tri-Clamp, ISO 2852 DN 76.1 (3"), AISI 316L/1.4435, EHEDG, 3A, ASME-BPE
DIN 11851 DN 80 PN 25 slotted nut, AISI 316L, EHEDG, 3A
DIN 11851 DN 80 PN 25 thread, AISI 316L, EHEDG, 3A
Pipe diaphragm seal Tri-Clamp, ISO 2852 DN 51 (2"), AISI 316L, 3A, PED Cat. II
DIN11851 DN50 PN25, pipe diaphragm seal, 316L, 3A
DIN11864-1 A DN50 PN25, pipe diaphragm seal, 316L, 3A
Pipe diaphragm seal Tri-Clamp, ISO 2852 DN 38 (1 1/2"), AISI 316L, 3A, PED Cat. II
DIN11851 DN32 PN40, pipe diaphragm seal, 316L, 3A
DIN11851 DN40 PN40, pipe diaphragm seal, 316L, 3A
3.1 material + pressure test PED Cat.II
DIN11864-1 A DN40 PN40, pipe diaphragm seal, 316L, 3A
EN/DIN flange DN 50 PN 10-40 B1, AISI 316L
EN/DIN flange DN 50 PN 63 B2, AISI 316L
EN/DIN flange DN 50 PN 100-160 E, AISI 316L
EN/DIN flange DN 50 PN 250 E, AISI 316L
EN/DIN flange DN 50 PN 400 E, AISI 316L
ANSI flange 2" 150 lbs RF, AISI 316/316L
ANSI flange 2" 300 lbs RF, AISI 316/316L
ANSI flange 2" 400/600 lbs RF, AISI 316/316L
ANSI flange 2" 900/1500 lbs RF, AISI 316/316L
ANSI flange 2" 2500 lbs RF, AISI 316/316L
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
7
KFJ
MRJ
MSJ
NKJ
NLJ
NZJ
TRJ
TIJ
JIS 10K 50A RF, AISI 316L
DIN 11851 DN 50 PN 25 slotted nut, AISI 316L, EHEDG, 3A
DIN 11851 DN 65 PN 25 slotted nut, AISI 316L, EHEDG, 3A
DIN 11851 DN 50 PN 25 thread, AISI 316L, EHEDG, 3A
DIN 11851 DN 65 PN 25 thread, AISI 316L, EHEDG, 3A
DIN 11864-2 A DN50 PN16 tube DIN11866-1, 316L, EHEDG, 3A
Varivent type N for pipes DN 40 – DN 162, PN 40, AISI 316L/1.4435, EHEDG, 3A
DRD DN50 (65 mm), PN 25, AISI 316L/1.4435
Curve type 8 up to 13
PN < 40 bar
TK Ambient 160
[mbar/10 K]
140
13
120
12
100
80
11
60
10
40
9
20
8
0
0
1
2
3
4
5
6
7
8
9
10
Capillary length
[m]
P01-PMP75xxx-05-xx-xx-xx-008
Diagram TK ambient as a function of the capillary length for PMP55, PN <40 bar (580 psi)
PN ³ 40 bar
TK Ambient 160
[mbar/10 K]
140
13
120
12
100
80
11
60
10
40
9
20
8
0
0
1
2
3
4
5
6
7
8
9
10
Capillary length
[m]
P01-PMP75xxx-05-xx-xx-xx-009
Diagram TK ambient as a function of the capillary length for PMP55, PN 40 bar (580 psi)
Endress+Hauser
65
Cerabar M PMC51, PMP51, PMP55
Characteristic
curve type
8
9
10
11
12
13
Ambient temperature range
Version in
the order
code
SBJ
SSJ
VAJ
FDJ
FMJ
TDJ
S4J
CQJ
KEJ
NXJ
TXJ
T2J
T5J
CPJ
AEJ
AQJ
NFJ
TJJ
T7J
T1J
T4J
CNJ
QIJ
QJJ
QSJ
ACJ
ANJ
A0J
A2J
A4J
KCJ
TCJ
Diaphragm seal
Pipe diaphragm seal Tri-Clamp, ISO 2852 DN 25 (1"), AISI 316L
DIN11851 DN25 PN40, pipe diaphragm seal, 316L, 3A
DIN11864-1 A DN25 PN40, pipe diaphragm seal, 316L, 3A
EN/DIN flange DN 50, PN 10-40 B1, extended diaphragm seal: 50 mm/100 mm/200 mm, AISI 316L
ANSI flange 2" 150 lbs, extended diaphragm seal: 2"/4"/6"/8", AISI 316/316L
Tri-Clamp, ISO 2852 DN 51 (2"), DIN 32676 DN 50, AISI 316L/1.4435
NEUMO BioControl D50 PN16, 316L, EHEDG, 3A
EN/DIN flange DN 40 PN 10-40 B1, AISI 316L
10K 40 RF, 316L, flange JIS B2220
DIN11864-2 A DN40 PN16 tube DIN11866-1, 316L, EHEDG, 3A
SMS 2" PN 25, AISI 316L/1.4435, EHEDG, 3A
APV-RJT 2" PN 40, AISI 316L/1.4435, 3A
APV-ISS 2" PN 40, AISI 316L/1.4435, 3A
EN/DIN flange DN32 PN 10-40 B1, AISI 316L
ANSI flange 1 1/2" 150 lbs RF, AISI 316/316L
ANSI flange 1 1/2" 300 lbs RF, AISI 316/316L
DIN11864-2 A DN32 PN16 tube DIN11866-1, 316L, EHEDG, 3A
Tri-Clamp, ISO 2852 DN 38 (1 1/2"), DIN 32676 DN 40, AISI 316L/1.4435, EHEDG, 3A, ASME-BPE
SMS 1 1/2" PN 25, AISI 316L/1.4435, EHEDG, 3A
APV-RJT 1 1/2" PN 40, AISI 316L/1.4435, 3A
APV-ISS 1 1/2" PN 40, AISI 316L/1.4435, 3A
EN/DIN flange DN 25 PN 10-40 B1, AISI 316L
EN/DIN flange DN 25 PN 63-160 E, AISI 316L
EN/DIN flange DN 25 PN 250 E, AISI 316L
EN/DIN flange DN 25 PN 400 E, AISI 316L
ANSI flange 1" 150 lbs RF, AISI 316/316L
ANSI flange 1" 300 lbs RF, AISI 316/316L
ANSI flange 1" 400/600 lbs RF, AISI 316/316L
ANSI flange 1" 900/1500 lbs RF, AISI 316/316L
ANSI flange 1" 2500 lbs RF, AISI 316/316L
JIS flange 10K 25 A RF, AISI 316L
Tri-Clamp, ISO 2852 DN 25 (1"), DIN 32676 DN 25, AISI 316L/1.4435, EHEDG, 3A, ASME-BPE
The operating temperature range of a diaphragm seal system depends on Fill fluid, "Capillary length and
internal diameter, Process temperature and Diaphragm seal oil volume.
The range of application can be extended by using a fill fluid with a smaller expansion coefficient and a shorter
capillary. The permitted operating temperature ranges in relation to the capillary length can be calculated
online at "Applicator Sizing Diaphragm Seal":
http://www.endress.com/applicator -> Applicator Sizing Diaphragm Seal -> Horncurve
P01-xxxxxxxx-20-xx-xx-en-001
66
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Note!
• Endress+Hauser recommends you use a low temperature oil for applications that require short response
times or are close to the lower temperature limit (see "diaphragm seal fill fluid").
• Please contact your Endress+Hauser sales office for further information, comprehensive diaphragm seal
system designs and measuring technology solutions that are close to the application limits.
Installation instructions
Instructions for diaphragm seal systems
• Endress+Hauser offer flushing rings as accessory to clean process isolating diaphragms without taking the
transmitters out of process.
For further information please contact your local Endress+Hauser Sales Center.
• A diaphragm seal together with the transmitter form a closed, calibrated system, which is filled through
openings in the diaphragm seal and in the transmitter's measurement system. These openings are sealed and
must not be opened.
• In the case of devices with diaphragm seals and capillaries, the zero point shift caused by the hydrostatic
pressure of the filling liquid column in the capillaries must be taken into account when selecting the
measuring cell. If a measuring cell with a small measuring range is selected, a position adjustment can cause
range violation.
• For devices with a temperature isolator or capillary, a suitable fastening device (mounting bracket) is
recommended.
• When using a mounting bracket, sufficient strain relief must be ensured in order to prevent the capillary
bending down (bending radius  100 mm (3.94 in)).
Installation instructions for capillaries
In order to obtain more precise measurement results and to avoid a defect in the device, mount the capillaries
as follows:
• Vibration-free (in order to avoid additional pressure fluctuations)
• Not in the vicinity of heating or cooling lines
• Insulate if the ambient temperature is below or above the reference temperature
• With a bending radius of 100 mm (3.94 in).
Vacuum applications
For applications under vacuum, Endress+Hauser recommends mounting the pressure transmitter below the
diaphragm seal. This prevents vacuum loading of the diaphragm seal caused by the presence of fill fluid in the
capillary.
When the pressure transmitter is mounted above the diaphragm seal, the maximum height difference H1 in
accordance with the illustration below must not be exceeded. The maximum height difference depends on the
density of the filling oil and the smallest ever pressure that is permitted to occur at the diaphragm seal (empty
container), see illustration below right.
When simultaneously applying the diaphragms seal at high process temperatures and low absolute pressures,
Endress+Hauser recommends the vacuum service (Feature 570 "Service" version "HG").
12.0
H1
Height difference H1 [m]
Low temperature oil
10.0
Vegetable oil
8.0
Silicone oil
6.0
High temperature
oil
4.0
Inert oil
2.0
0.0
50 100 200
300
400
500
600
700
800
900 1000
Pressure at diaphragm seal [mbarabs]
P01-PMx5xxxx-11-xx-xx-xx-006
Installation above the diaphragm seal
Endress+Hauser
P01-PMP75xxx-05-xx-xx-xx-011
Diagram of maximum installation height above the diaphragm seal for
vacuum applications
67
Cerabar M PMC51, PMP51, PMP55
Certificates and approvals
CE mark
The device meets the legal requirements of the relevant EC directives.
Endress+Hauser confirms that the device has been successfully tested by applying the CE mark.
Ex approvals
•
•
•
•
•
ATEX
IECEx
FM
CSA
Also combinations of different approvals
All explosion protection data are given in separate documentation which is available upon request. The
Ex documentation is supplied as standard with all devices approved for use in explosion hazardous areas.
 ä 85 ff, "Safety Instructions" and "Installation/Control Drawings" sections.
Pressure Equipment Directive
(PED)
The devices PMC51, PMP51 and PMP55 correspond to Article 3 (3) of the EC directive 97/23/EC (Pressure
Equipment Directive) and have been designed and manufactured according to good engineering practice.
The following also applies:
– PMP51/PMP55 with threaded connection and internal process isolating diaphragm PN > 200:
Suitable for stable gases in group 1, category I
– PMP55 with pipe diaphragm seal 1.5"/PN40:
Suitable for stable gases in group 1, category II
– PMP55 with separators PN400:
Suitable for stable gases in group 1, category I
Standards and guidelines
DIN EN 60770 (IEC 60770):
Transmitters for use in industrial process control systems
Part 1: Methods for inspection and routine testing
DIN 16086:
Electrical pressure measuring instruments, pressure sensors, pressure transmitters, pressure measuring
instruments,
concepts, specifications on data sheets
EN 61326 series:
EMC product family standard for electrical equipment for measurement, control and laboratory use.
68
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Ordering information
PMC51
This overview does not mark options which are mutually exclusive.
10
Approval:
AA
BA
BD
BE
BF
BG
B1
8C
IA
IE
IF
I1
CA
CD
FA
FD
99
20
Output:
1
2
9
30
F31 aluminum
F31 aluminum, glass window
F15 Stainless Steel Hygiene
F15 Stainless Steel Hygiene, glass window
F15 Stainless Steel Hygiene, plastic window
Special version
Electrical connection:
A
B
C
D
I
M
P
S
V
Y
Endress+Hauser
LCD, push buttons
W/o LCD, push buttons
Special version
Housing:
I
J
Q
R
S
Y
50
4-20mA Analog
4-20mA HART
Special version
Display, operation:
1
2
9
40
For non-hazardous areas
ATEX II 1/2G Ex ia IIC T6
ATEX II 3G Ex nA IIC T6
ATEX II 2G Ex ia IIC T6
ATEX II 1/2D Ex ia IIIC
ATEX II 3G Ex ic IIC T6
ATEX II 1/2G Ex ia IIC T6 + ATEX II 1/2D Ex iaD
ATEX II Ex ia + FM/CSA IS
ATEX II 1/2G Ex ia IIC T6+
FM/CSA IS Cl.I Div. 1 Gr. A-D
FM/CSA: zone0,1,2
IEC Ex ia IIC T6 Ga/Gb
IEC Ex ic IIC T6 Gc
IEC Ex ia IIIC Da/ Db
IEC Ex ia IIC T6 Ga/Gb+Ex ia IIIC Da/Db
CSA C/US IS Cl.I,II,III Div.1 Gr. A-G,
CSA C/US IS Cl.I Div.2 Gr. A-D, Ex ia
CSA General Purpose
FM IS Cl.I,II,III Div.1 Gr.A-G, AEx ia
FM NI Cl.I Div.2 Gr.A-D,
FM IS: zone 0,1,2,20,21,22/FM NI: zone 2
FM NI Cl.I Div.2 Gr. A-D
Special version
Gland M20, IP66/68 NEMA4X/6P
Thread M20, IP66/68 NEMA4X/6P
Thread G1/2, IP66/68 NEMA4X/6P
Thread NPT1/2, IP66/68 NEMA4X/6P
Connector M12, IP66/68, NEMA4X/6P
Connector 7/8", IP66/68, NEMA4X/6P
Connector Han7D, 90deg, IP65
Cable 5m, IP66/68 NEMA4X/6P + pressure compensation via cable
Valve connector ISO4400 M16, IP64
Special version
69
Cerabar M PMC51, PMP51, PMP55
PMC51 (continued)
70
Sensor range:
1C
1E
1F
1H
1K
1M
1P
1S
2C
2E
2F
2H
2K
2M
2P
2S
99
80
Reference accuracy:
D
G
Y
90
Platinum
Standard
Special version
Calibration; Unit:
A
B
C
D
E
F
J
K
Y
70
100mbar/10kPa/1.5psi relative,
1mH2O/3ftH2O/40inH2O
Overload: 4bar/400kPa/60psi
250mbar/25kPa/3.75psi relative,
2.5mH2O/7.5ftH2O/100inH2O
Overload: 5bar/500kPa/75psi
400mbar/40kPa/6psi relative,
4mH2O/13ftH2O/160inH2O
Overload: 8bar/800kPa/120psi
1bar/100kPa/15psi relative,
10mH2O/33ftH2O/400inH2O
Overload: 10bar/1MPa/150psi
2bar/200kPa/30psi relative,
20mH2O/67ftH2O/800inH2O
Overload: 18bar/1.8MPa/270psi
4bar/400kPa/60psi relative,
40mH2O/133ftH2O/1600inH2O
Overload: 25bar/2.5MPa/375psi
10bar/1MPa/150psi relative,
100mH2O/333ftH2O/4000inH2O
Overload: 40bar/4MPa/600psi
40bar/4MPa/600psi relative,
400mH2O/1334ftH2O/16000inH2O
Overload: 60bar/6MPa/900psi
100mbar/10kPa/1.5psi abs,
1mH2O/3ftH2O/40inH2O
Overload: 4bar/400kPa/60psi
250mbar/25kPa/3.75psi abs,
2.5mH2O/7.5ftH2O/100inH2O
Overload: 5bar/500kPa/75psi
400mbar/40kPa/6psi abs,
4mH2O/13ftH2O/160inH2O
Overload: 8bar/800kPa/120psi
1bar/100kPa/15psi abs,
10mH2O/33ftH2O/400inH2O
Overload: 10bar/1MPa/150psi
2bar/200kPa/30psi abs,
20mH2O/67ftH2O/800inH2O abs
Overload: 18bar/1.8MPa/270psi
4bar/400kPa/60psi abs,
40mH2O/133ftH2O/1600inH2O abs
Overload: 25bar/2.5MPa/375psi
10bar/1MPa/150psi abs,
100mH2O/333ftH2O/4000inH2O abs
Overload: 40bar/4MPa/600psi
40bar/4MPa/600psi abs,
400mH2O/1334ftH2O/16000inH2O abs
Overload: 60bar/6MPa/900psi
Special version
Sensor range; %
Sensor range; mbar/bar
Sensor range; kPa/MPa
Sensor range; mm/mH2O
Sensor range; inH2O/ftH2O
Sensor range; psi
Customized pressure; see additional spec.
Customized level; see additional spec.
Special version
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
PMC51 (continued)
110
Process connection:
ANSI flanges
ACJ
1" 150lbs RF, 316/316L, flange ANSI B16.5
AEJ
1-1/2" 150lbs RF, 316/316L, flange ANSI B16.5
AFF
2" 150lbs RF, PVDF, flange ANSI B16.5
AFJ
2" 150lbs RF, 316/316L, flange ANSI B16.5
AFN 2" 150lbs, ECTFE>316/316L, flange ANSI B16.5
AGF 3" 150lbs RF, PVDF, flange ANSI B16.5
AGJ
3" 150lbs RF, 316/316L, flange ANSI B16.5
AGN 3" 150lbs, ECTFE>316/316L, flange ANSI B16.5
AHJ
4" 150lbs RF, 316/316L, flange ANSI B16.5
AHN 4" 150lbs, ECTFE>316/316L, flange ANSI B16.5
ANJ
1" 300lbs RF, 316/316L, flange ANSI B16.5
AQJ
1-1/2" 300lbs RF, 316/316L, flange ANSI B16.5
ARJ
2" 300lbs RF, 316/316L, flange ANSI B16.5
ASJ
3" 300lbs RF, 316/316L, flange ANSI B16.5
ATJ
4" 300lbs RF, 316/316L, flange ANSI B16.5
EN flanges
CNJ
DN25 PN10-40 B1, 316L, flange EN1092-1
CPJ
DN32 PN10-40 B1, 316L, flange EN1092-1
CQJ
DN40 PN10-40 B1, 316L, flange EN1092-1
CXJ
DN50 PN10-40 B1, 316L, flange EN1092-1
CFF
DN50 PN10/16 B1, PVDF, flange EN1092-1
CRP
DN50 PN25/40, ECTFE>316L, flange EN1092-1
CZJ
DN80 PN10-40 B1, 316L, flange EN1092-1
CSP
DN80 PN25/40, ECTFE>316L, flange EN1092-1
JIS flanges
KFJ
10K 50 RF, 316L, flange JIS B2220
KGJ
10K 80 RF, 316L, flange JIS B2220
KHJ
10K 100 RF, 316L, flange JIS B2220
Threaded connection
GCC Thread ISO228 G1/2, AlloyC
GCF Thread ISO228 G1/2, PVDF
GCJ
Thread ISO228 G1/2, 316L
GLC Thread ISO228 G1/2 G1/4 female, AlloyC
GLJ
Thread ISO228 G1/2 G1/4 female, 316L
GMC Thread ISO228 G1/2 hole 11.4mm, AlloyC
GMJ Thread ISO228 G1/2 hole 11.4mm, 316L
GNJ
Thread JIS B0202 G1/2 male, 316L
GOJ
Thread JIS B0203 R1/2 male, 316L
GVJ
Thread ISO228 G1-1/2, 316L, flush-mounted
GWJ Thread ISO228 G2, 316L, flush-mounted
G4J
Thread DIN13 M44x1.25, 316L, flush-mounted
Threaded connection as per ANSI
RJF
Thread ANSI MNPT1/2 hole 3mm, PVDF
RKC Thread ANSI MNPT 1/2 hole, 11,4mm, Alloy C
RKJ
Thread ANSI MNPT1/2 hole 11.4mm, 316L
RLC
Thread ANSI MNPT1/2 FNPT1/4, AlloyC
RLJ
Thread ANSI MNPT1/2 FNPT1/4, 316L
R1C
Thread ANSI FNPT 1/2, Alloy C
R1J
Thread ANSI FNPT 1/2, 316L
U7J
Thread ANSI MNPT1-1/2, 316L, flush-mounted
U8J
Thread ANSI MNPT2, 316L, flush-mounted
YYY
190
Seal:
A
B
G
F
J
K
Y
Endress+Hauser
Special version
FKM Viton
FKM Viton, FDA
HNBR, FDA, 3A Class II, KTW, AFNOR, BAM
NBR
EPDM
EPDM, FDA, 3A Class II, USP Class VI, DVGW, KTW, W270, WRAS, ACS, NSF61
Special version
71
Cerabar M PMC51, PMP51, PMP55
PMC51 (continued)
Additional ordering information (optional)
500
Operating language:
AA
AB
AC
AD
AE
AF
AK
AL
550
Calibration:
F1
F2
570
P4
QJ
QK
QL
RL
RM
RN
01.00.zz, HART, DevRev01
Identification:
Z1
Z2
72
Mounting bracket, wall/pipe, 30
Shutoff valve (PZAV), see additional spec
-R1A1 PZAV-R1A1 Shutoff valve, G1/2, C22.8
-R1A2 PZAV-R1A2 Shutoff valve, G1/2, 316Ti
-R1D1 PZAV-R1D1 Shutoff valve, NPT1/2, C22.8
-R1D2 PZAV-R1D2 Shutoff valve, NPT1/2, 316Ti
-B1A2 PZAV-B1A2 Shutoff valve., G1/2, 316Ti, 3.1
-B1D2 PZAV-B1D2 Shutoff valve., NPT1/2, 316Ti, 3.1
Siphon (PZW), see additional spec
-RA21 PZW-RA21 Siphon G1/2 vertical, C22.8
-RA22 PZW-RA22 Siphon G1/2 vertical, 316Ti
-RC11 PZW-RC11 Siphon G1/2 x weld. horiz. C22.8
-RD11 PZW-RD11 Siphon NPT1/2 x weld. horiz. C22.8
-BB22 PZW-BB22 Siphon NPT1/2 vertical, 316Ti, 3.1
-BA22 PZW-BA22 Siphon NPT1/2x weld.vert.316Ti 3.1
Welding neck G1-1/2, 316
Welding neck G1-1/2, 316L, 3.1, EN10204-3.1 material, inspection certificat
Weld-in tool adapter G1-1/2, bras
Plug-in jack M12
Plug-in jack M12, 90deg
Plug-in jack M12, 90deg+5m cable
Software version:
78
895
Overvoltage protection
Accessory enclosed
PA
P2
850
Cable PE, 2m/80inch + housing mounting bracket, wall/pipe, 304
Cable PE, 5m/200inch + housing mounting bracket, wall/pipe, 304
Cable PE, 10m/400inch + housing mounting bracket, wall/pipe, 304
Cable FEP, 5m/200inch IP69K + housing mounting bracket, wall/pipe, 304
Accessory mounted:
NA
620
EN10204-3.1 process connection material, inspection certificate
NACE MR0175 process connection
EN10204-3.1 helium leak test, inspection certificate
EN10204-3.1 pressure test, inspection certificate
Special version,
Separate housing:
MA
MB
MC
MH
610
Oil and grease removed
Cleaned for oxygen service
Cleaned for silicone-free applications
Configured min alarm current
Configured HART Burst Mode PV
Special version
Test, certificate:
JA
JB
KD
KE
K9
600
Factory calibration certificate, 5-point
DKD calibration certificate 10-point
Service:
HA
HB
HC
IA
IB
I9
580
English
German
French
Spanish
Italian
Dutch
Chinese
Japanese
Measuring point (TAG)
Bus address
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
PMC51 (continued)
10
20
You can enter the versions for the specific feature in the following table. The versions entered make up the
complete order code.
30
40
50
70
80
90
110
190
500
550
570
580
600
610
620
850
895
PMC51 -
Endress+Hauser
73
Cerabar M PMC51, PMP51, PMP55
PMP51
This overview does not mark options which are mutually exclusive.
10
Approval:
AA
BA
BB
BC
BD
BE
BG
B1
B2
IA
IB
ID
IE
I1
CA
CB
CC
CD
C1
FA
FB
FD
F1
99
20
Output:
1
2
9
30
F31 aluminum
F31 aluminum, glass window
F15 Stainless Steel Hygiene
F15 Stainless Steel Hygiene, glass window
F15 Stainless Steel Hygiene, plastic window
Special version
Electrical connection:
A
B
C
D
I
M
P
S
V
Y
74
LCD, push buttons
W/o LCD, push buttons
Special version
Housing:
I
J
Q
R
S
Y
50
4-20mA Analog
4-20mA HART
Special version
Display, operation:
1
2
9
40
For non-hazardous areas
ATEX II 1/2G Ex ia IIC T6
ATEX II 1/2D Ex t IIIC
ATEX II 2G Ex d IIC T6
ATEX II 3G Ex nA IIC T6
ATEX II 2G Ex ia IIC T6
ATEX II 3G Ex ic IIC T6
ATEX II 1/2G Ex ia IIC T6 + ATEX II 1/2D
ATEX II 1/2G Ex ia IIC T6 + ATEX II 2G
IEC Ex ia IIC T6 Ga/Gb
IEC Ex d IIC T6 Gb
IEC Ex t IIIC Da/Db
IEC Ex ic IIC T6 Gc
IEC Ex ia IIC T6 Ga/Gb+Ex ia IIIC Da/Db
CSA C/US IS Cl.I,II,III Div.1 Gr.A-G,
CSA C/US IS Cl.I Div.2 Gr.2 Gr.A-D, Ex ia, zone 0,1,2
CSA C/US XP Cl.I, II Div.1 Gr.B-G, Ex d (factory sealed), zone 1,2
CSA C/US Cl.II, III Div.1 Gr.E-G
CSA General Purpose
CSA C/US IS/XP Cl.I, II Div.1 Gr.A-G/B-G
FM IS Cl.I,II,III Div.1 Gr.A-G, AEx ia
FM NI Cl.I Div.2 Gr.A-D
FM IS: zone 0,1,2,20,21,22/FM NI: zone 2
FM XP Cl.I, II Div.1 Gr.A-D, AEx d (Factory sealed) zone 1,2
FM NI Cl.I Div.2 Gr. A-D
FM IS/XP Cl.I, II Div.1 Gr.A-G, zone 1,2
Special version
Gland M20, IP66/68 NEMA4X/6P
Thread M20, IP66/68 NEMA4X/6P
Thread G1/2, IP66/68 NEMA4X/6P
Thread NPT1/2, IP66/68 NEMA4X/6P
Connector M12, IP66/68, NEMA4X/6P
Connector 7/8", IP66/68, NEMA4X/6P
Connector Han7D, 90deg, IP65
Cable 5m, IP66/68 NEMA4X/6P + pressure compensation via cable
Valve connector ISO4400 M16, IP64
Special version
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
PMP51 (continued)
70
Sensor range:
1F
1H
1K
1M
1P
1S
1U
1W
2F
2H
2K
2M
2P
2S
2U
2W
99
80
Reference accuracy:
D
G
Y
90
Platinum
Standard
Special version
Calibration; Unit:
A
B
C
D
E
F
J
K
Y
Endress+Hauser
400mbar/40kPa/6psi relative,
4mH2O/13ftH2O/160inH2O
Overload: 6bar/600kPa/90psi
1bar/100kPa/15psi relative,
10mH2O/33ftH2O/400inH2O
Overload: 10bar/1MPa/150psi
2bar/200kPa/30psi relative,
20mH2O/67ftH2O/800inH2O
Overload: 20bar/2MPa/300psi
4bar/400kPa/60psi relative,
40mH2O/133ftH2O/1600inH2O
Overload: 28bar/2.8MPa/420psi
10bar/1MPa/150psi relative,
100mH2O/333ftH2O/4000inH2O
Overload: 40bar/4MPa/600psi
40bar/4MPa/600psi relative,
400mH2O/1334ftH2O/16000inH2O
Overload: 160bar/16MPa/2400psi
100bar/10MPa/1500psi relative,
1000mH2O/3330ftH2O/40000inH2O
Overload: 400bar/40MPa/6000psi
400bar/40MPa/6000psi relative,
4000mH2O/13340ftH2O/160000inH2O
Overload: 600bar/60MPa/9000psi
400mbar/40kPa/6psi abs,
4mH2O/13ftH2O/160inH2O
Overload: 6bar/600kPa/90psi
1bar/100kPa/15psi abs,
10mH2O/33ftH2O/400inH2O
Overload: 10bar/1MPa/150psi
2bar/200kPa/30psi abs,
20mH2O/67ftH2O/800inH2O
Overload: 10bar/1MPa/150psi
4bar/400kPa/60psi abs,
40mH2O/133ftH2O/1600inH2O abs
Overload: 28bar/2.8MPa/420psi
10bar/1MPa/150psi abs,
100mH2O/333ftH2O/4000inH2O abs
Overload: 40bar/4MPa/600psi
40bar/4MPa/600psi abs,
400mH2O/1334ftH2O/16000inH2O abs
Overload: 160bar/16MPa/2400psi
100bar/10MPa/1500psi abs,
1000mH2O/3330ftH2O/40000inH2O abs
Overload: 400bar/40MPa/6000psi
400bar/40MPa/6000psi abs,
4000mH2O/13340ftH2O/160000inH2O abs
Overload: 600bar/60MPa/9000psi
Special version
Sensor range; %
Sensor range; mbar/bar
Sensor range; kPa/MPa
Sensor range; mm/mH2O
Sensor range; inH2O/ftH2O
Sensor range; psi
Customized pressure; see additional spec.
Customized level; see additional spec.
Special version
75
Cerabar M PMC51, PMP51, PMP55
PMP51 (continued)
110
Process connection:
ANSI flanges
AEJ
1-1/2" 150lbs RF, 316/316L, flange ANSI B16.5
AFJ
2" 150lbs RF, 316/316L, flange ANSI B16.5
AGJ
3" 150lbs RF, 316/316L, flange ANSI B16.5
AHJ
4" 150lbs RF, 316/316L, flange ANSI B16.5
ANJ
1" 300lbs RF, 316/316L, flange ANSI B16.5
AQJ
1-1/2" 300lbs RF, 316/316L, flange ANSI B16.5
ARJ
2" 300lbs RF, 316/316L, flange ANSI B16.5
ASJ
3" 300lbs RF, 316/316L, flange ANSI B16.5
ATJ
4" 300lbs RF, 316/316L, flange ANSI B16.5
EN flanges
CNJ
DN25 PN10-40 B1, 316L, flange EN1092-1
CPJ
DN32 PN10-40 B1, 316L, flange EN1092-1
CQJ
DN40 PN10-40 B1, 316L, flange EN1092-1
CXJ
DN50 PN25/40 B1, 316L flange EN1092-1
CZJ
DN80 PN25/40 B1, 316L, flange EN1092-1
Threaded connection
GCC Thread ISO228 G1/2, AlloyC
GCJ
Thread ISO228 G1/2, 316L
GLC Thread ISO228 G1/2 G1/4 female, AlloyC
GLJ
Thread ISO228 G1/2 G1/4 female, 316L
GMC Thread ISO228 G1/2 hole 11.4mm, AlloyC
GMJ Thread ISO228 G1/2 hole 11.4mm, 316L
GRC Thread ISO228 G1/2, AlloyC, flush-mounted
GRJ
Thread ISO228 G1/2, 316L, flush-mounted
GTJ
Thread ISO228 G1, 316L, flush-mounted
GVJ
Thread ISO228 G1-1/2, 316L, flush-mounted
GWJ Thread ISO228 G2, 316L, flush-mounted
G0J
Thread ISO228 G1/2 seal O-ring, fm= flush-mounted, 316L, adapter 52002643
G1J
Thread DIN13 M20x1.5, 316L
Threaded connection as per ANSI
RKC Thread ANSI MNPT1/2 hole 11.4mm, AlloyC
RKJ
Thread ANSI MNPT1/2 hole 11.4mm, 316L
RLC
Thread ANSI MNPT1/2 FNPT1/4, AlloyC
RLJ
Thread ANSI MNPT1/2 FNPT1/4, 316L
R1C
Thread ANSI FNPT 1/2, Alloy C
R1J
Thread ANSI FNPT 1/2, 316L
U5J
Thread ANSI MNPT1, 316L, flush-mounted
U7J
Thread ANSI MNPT1-1/2, 316L, flush-mounted
U8J
Thread ANSI MNPT2, 316L, flush-mounted
XSJ
Prepared for diaphragm seal mount, 316L
YYY
Special version
170
Material of the process isolating diaphragm:
A
B
M
Y
180
Fill fluid:
1
2
9
76
316L
AlloyC
Rhodium>gold>316L
Special version
Silicone oil
Inert oil
Special version
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
PMP51 (continued)
Additional ordering information (optional)
500
Operating language:
AA
AB
AC
AD
AE
AF
AK
AL
550
Calibration:
F1
F2
570
P4
QA
QB
QC
QG
QJ
QK
QL
RL
RM
RN
Mounting bracket, wall/pipe, 30
Shutoff valve (PZAV), see additional spec
-R1A1
PZAV-R1A1 Shutoff valve, G1/2, C22.8
-R1A2
PZAV-R1A2 Shutoff valve, G1/2, 316Ti
-R1D1 PZAV-R1D1 Shutoff valve, NPT1/2, C22.8
-R1D2 PZAV-R1D2 Shutoff valve, NPT1/2, 316Ti
-B1A2
PZAV-B1A2 Shutoff valve., G1/2, 316Ti, 3.1
-B1D2 PZAV-B1D2 Shutoff valve., NPT1/2, 316Ti, 3.1
Siphon (PZW), see additional spec
-RA21
PZW-RA21 Siphon G1/2 vertical, C22.8
-RA22
PZW-RA22 Siphon G1/2 vertical, 316Ti
-RC11 PZW-RC11 Siphon G1/2 x weld. horiz. C22.8
-RD11 PZW-RD11 Siphon NPT1/2 x weld. horiz. C22.8
-BB22
PZW-BB22 Siphon NPT1/2 vertical, 316Ti, 3.1
-BA22
PZW-BA22 Siphon NPT1/2x weld.vert.316Ti 3.1
Welding neck G1/2, 316L
Welding neck G1/2, 316L, 3.1, EN10204-3.1 material, inspection certificat
Weld-in tool adapter G1/2, bras
Weld-in tool adapter G1, brass, metal sealing tape
Welding neck G1-1/2, 316
Welding neck G1-1/2, 316L, 3.1, EN10204-3.1 material, inspection certificat
Weld-in tool adapter G1-1/2, bras
Plug-in jack M1
Plug-in jack M12, 90de
Plug-in jack M12, 90deg+5m cabl
Software version:
78
Endress+Hauser
Overvoltage protection
Accessory enclosed
PA
P2
850
Cable PE, 2m/80inch + housing mounting bracket, wall/pipe, 304
Cable PE, 5m/200inch + housing mounting bracket, wall/pipe, 304
Cable PE, 10m/400inch + housing mounting bracket, wall/pipe, 304
Cable FEP, 5m/200inch IP69K + housing mounting bracket, wall/pipe, 304
Accessory mounted:
NA
620
EN10204-3.1 wetted material, inspection certificate
NACE MR0175 wetted
EN10204-3.1 wetted material + AD2000 pressurized
EN10204-3.1 wetted material + Ra, Ra= surface roughness, dimensional check, inspection certificate
EN10204-3.1 helium leak test, inspection certificate
EN10204-3.1 pressure test, inspection certificate
EN10204-3.1 PMI test (PMI = positive material identification), inspection certificate
Special version
Separate housing:
MA
MB
MC
MH
610
Oil and grease removed
Cleaned for oxygen service
Cleaned for silicone-free applications
Configured min alarm current
Configured HART Burst Mode PV
Special version
Test, certificate:
JA
JB
JF
KB
KD
KE
KG
K9
600
Factory calibration certificate, 5-point
DKD calibration certificate 10-point
Service:
HA
HB
HC
IA
IB
I9
580
English
German
French
Spanish
Italian
Dutch
Chinese
Japanese
01.00.zz, HART, DevRev01
77
Cerabar M PMC51, PMP51, PMP55
PMP51 (continued)
895
Identification:
Z1
Z2
Measuring point (TAG)
Bus address
You can enter the versions for the specific feature in the following table. The versions entered make up the
complete order code.
10
20
30
40
50
70
80
90
110
170
180
500
550
570
580
600
610
620
850
895
PMP51 -
78
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
PMP55
This overview does not mark options which are mutually exclusive.
10
Approval:
AA
BA
BB
BC
BD
BE
BG
B1
B2
8A
8B
IA
IB
ID
IE
I1
CA
CB
CC
CD
C1
FA
FB
FC
FD
F1
99
20
Output:
1
2
9
30
F31 aluminum
F31 aluminum, glass window
F15 Stainless Steel Hygiene
F15 Stainless Steel Hygiene, glass window
F15 Stainless Steel Hygiene, plastic window
Special version
Electrical connection:
A
B
C
D
I
M
P
S
V
Y
Endress+Hauser
LCD, keys on display/electronics
Without LCD, keys on electronics
Special version
Housing:
I
J
Q
R
S
Y
50
4-20mA Analog
4-20mA HART
Special version
Display, operation:
1
2
9
40
For non-hazardous areas
ATEX II 1/2G Ex ia IIC T6
ATEX II 1/2D Ex t IIIC
ATEX II 2G Ex d IIC T6
ATEX II 3G Ex nA IIC T6
ATEX II 2G Ex ia IIC T6
ATEX II 3G Ex ic IIC T6
ATEX II 1/2G Ex ia IIC T6 + ATEX II 1/2D
ATEX II 1/2G Ex ia IIC T6 + ATEX II 2G
ATEX II Ex ia/Ex d + FM/CSA IS + XP
ATEX II 1/2G Ex ia IIC T6+
ATEX II 2G Ex d IIC T6+
FM/CSA IS + XP Cl.I, II Div.1 Gr. A-G/B-G, zone 1,2
FM/CSA IS + XP Cl.I, II Div.1 Gr.A-D/B-G
FM IS/FM XP Cl.I, II Div.1 Gr.A-G+
CSA IS/XP Cl.I, II Div.1 Gr.A-G, zone 1,2
IEC Ex ia IIC T6 Ga/Gb
IEC Ex d IIC T6 Gb
IEC Ex t IIIC Da/Db
IEC Ex ic IIC T6 Gc
IEC Ex ia IIC T6 Ga/Gb+Ex ia IIIC Da/Db
CSA C/US IS Cl.I,II,III Div.1 Gr.A-G,
CSA C/US IS Cl.I Div.2 Gr.2 Gr.A-D, Ex ia, zone 0,1,2
CSA C/US CP Cl.I, II Div.1 Gr.B-G, Ex d (factory sealed) zone 1,2
CSA C/US Cl.II, III Div.1 Gr.E-G, zone 21,22
CSA General Purpose
CSA C/US IS/XP CL.I, II Div.1 Gr.A-G/B-G, zone 1,2
FM IS Cl.I,II,III Div.1 Gr.A-G, AEx ia
FM NI Cl.I Div.2 Gr.A-D,
FM IS: zone 0,1,2,20,21,22/FM NI: zone 2
FM XP Cl.I, II Div.1 Gr.A-G, AEx d (factory sealed) zone 1,2
FM DIP Cl.II, III Div.1 Gr.A-G, zone 21,22
FM NI Cl.I Div.2 Gr. A-D
FM IS/XP Cl.I, II Div.1 Gr.A-G, zone 1,2
Special version
Gland M20, IP66/68 NEMA4X/6P
Thread M20, IP66/68 NEMA4X/6P
Thread G1/2, IP66/68 NEMA4X/6P
Thread NPT1/2, IP66/68 NEMA4X/6P
Connector M12, IP66/68, NEMA4X/6P
Connector 7/8", IP66/68, NEMA4X/6P
Connector Han7D, 90deg, IP65
Cable 5m, IP66/68 NEMA4X/6P + pressure compensation via cable
Valve connector ISO4400 M16, IP64
Special version
79
Cerabar M PMC51, PMP51, PMP55
PMP55 (continued)
70
Sensor range:
1F
1H
1K
1M
1P
1S
1U
1W
2F
2H
2K
2M
2P
2S
2U
2W
99
80
Reference accuracy:
D
G
Y
90
Platinum
Standard
Special version
Calibration; Unit:
A
B
C
D
E
F
J
K
Y
80
400mbar/40kPa/6psi relative,
4mH2O/13ftH2O/160inH2O
Overload: 6bar/600kPa/90psi
1bar/100kPa/15psi relative,
10mH2O/33ftH2O/400inH2O
Overload: 10bar/1MPa/150psi
2bar/200kPa/30psi relative,
20mH2O/67ftH2O/800inH2O
Overload: 20bar/2MPa/300psi
4bar/400kPa/60psi relative,
40mH2O/133ftH2O/1600inH2O
Overload: 28bar/2.8MPa/420psi
10bar/1MPa/150psi relative,
100mH2O/333ftH2O/4000inH2O
Overload: 40bar/4MPa/600psi
40bar/4MPa/600psi relative,
400mH2O/1334ftH2O/16000inH2O
Overload: 160bar/16MPa/2400psi
100bar/10MPa/1500psi relative,
1000mH2O/3330ftH2O/40000inH2O
Overload: 400bar/40MPa/6000psi
400bar/40MPa/6000psi relative,
4000mH2O/13340ftH2O/160000inH2O
Overload: 600bar/60MPa/9000psi
400mbar/40kPa/6psi abs,
4mH2O/13ftH2O/160inH2O
Overload: 6bar/600kPa/90psi
1bar/100kPa/15psi abs,
10mH2O/33ftH2O/400inH2O
Overload: 10bar/1MPa/150psi
2bar/200kPa/30psi abs,
20mH2O/67ftH2O/800inH2O abs
Overload: 20bar/2MPa/300psi
4bar/400kPa/60psi abs,
40mH2O/133ftH2O/1600inH2O abs
Overload: 28bar/2.8MPa/420psi
10bar/1MPa/150psi abs,
100mH2O/333ftH2O/4000inH2O abs
Overload: 40bar/4MPa/600psi
40bar/4MPa/600psi abs,
400mH2O/1334ftH2O/16000inH2O abs
Overload: 160bar/16MPa/2400psi
100bar/10MPa/1500psi abs,
1000mH2O/3330ftH2O/40000inH2O abs
Overload: 400bar/40MPa/6000psi
400bar/40MPa/6000psi abs,
4000mH2O/13340ftH2O/160000inH2O abs
Overload: 600bar/60MPa/9000psi
Special version
Sensor range; %
Sensor range; mbar/bar
Sensor range; kPa/MPa
Sensor range; mm/mH2O
Sensor range; inH2O/ftH2O
Sensor range; psi
Customized pressure; see additional spec.
Customized level; see additional spec.
Special version
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
PMP55 (continued)
110
Process connection:
ANSI flanges
ACJ
1" 150lbs RF, 316/316L, flange ANSI B16.5
AEJ
1-1/2" 150lbs RF, 316/316L, flange ANSI B16.5
AFJ
2" 150lbs RF, 316/316L, flange ANSI B16.5
AGJ
3" 150lbs RF, 316/316L, flange ANSI B16.5
AHJ
4" 150lbs RF, 316/316L, flange ANSI B16.5
ANJ
1" 300lbs RF, 316/316L, flange ANSI B16.5
AQJ
1-1/2" 300lbs RF, 316/316L, flange ANSI B16.5
ARJ
2" 300lbs RF, 316/316L, flange ANSI B16.5
ASJ
3" 300lbs RF, 316/316L, flange ANSI B16.5
ATJ
4" 300lbs RF, 316/316L, flange ANSI B16.5
A0J
1" 400/600lbs RF, 316/316L, flange ANSI B16.5
A1J
2" 400/600lbs RF, 316/316L, flange ANSI B16.5
A2J
1" 900/1500lbs RF, 316/316L, flange ANSI B16.5
A3J
2" 900/1500lbs RF, 316/316L, flange ANSI B16.5
A4J
1" 2500lbs RF, 316/316L, flange ANSI B16.5
A5J
2" 2500lbs RF, 316/316L, flange ANSI B16.5
FMJ
2" 150lbs RF, 316/316L, 2/4/6/8" extended diaphragm seal, flange ANSI B16.5, see additional spec.
FNJ
3" 150lbs RF, 316/316L, 2/4/6/8" extended diaphragm seal, flange ANSI B16.5, see additional spec.
FOJ
4" 150lbs RF, 316/316L, 2/4/6/8" extended diaphragm seal, flange ANSI B16.5, see additional spec.
FWJ
3" 300lbs RF, 316/316L, 2/4/6/8" extended diaphragm seal, flange ANSI B16.5, see additional spec.
FXJ
4" 300lbs RF, 316/316L, 2/4/6/8" extended diaphragm seal, flange ANSI B16.5, see additional spec.
EN flanges
CNJ
DN25 PN10-40 B1, 316L, flange EN1092-1
CPJ
DN32 PN10-40 B1, 316L, flange EN1092-1
CQJ
DN40 PN10-40 B1, 316L, flange EN1092-1
CXJ
DN50 PN10-40 B1, 316L, flange EN1092-1
CZJ
DN80 PN10-40 B1, 316L, flange EN1092-1
JIS flanges
KCJ
10K 25 RF, 316L, flange JIS B2220
KEJ
10K 40 RF, 316L, flange JIS B2220
KFJ
10K 50 RF, 316L, flange JIS B2220
KGJ
10K 80 RF, 316L, flange JIS B2220
KHJ
10K 100 RF, 316L, flange JIS B2220
DIN flanges
QIJ
DN25 PN63-160 E, 316L, flange DIN2501
QJJ
DN25 PN250 E, 316L, flange DIN2501
QMJ DN50 PN250 E, 316L, flange DIN2501
QOJ
DN50 PN100-160 E, 316L, flange DIN2501
QSJ
DN25 PN400 E, 316L, flange DIN2501
QVJ
DN50 PN400 E, 316L, flange DIN2501
FDJ
DN50 PN10-40 B1, 316L, 50/100/200mm extended diaphragm seal, flange EN1092-1, see additional spec.
FEJ
DN80 PN10-40 B1, 316L, 50/100/200mm extended diaphragm seal, flange EN1092-1, see additional spec.
PDJ
DN50 PN63 B2, 316L, flange EN1092-1
PPJ
DN80 PN100 B2, 316L, flange EN1092-1
PQJ
DN100 PN100 B2, 316L, flange EN1092-1
Threaded connection
GTC Thread ISO228 G1, AlloyC, flush-mounted
GTJ
Thread ISO228 G1, 316L, flush-mounted
GVC Thread ISO228 G1-1/2, AlloyC, fm= flush-mounted
GVJ
Thread ISO228 G1-1/2, 316L, flush-mounted
GWC Thread ISO228 G2, AlloyC, flush-mounted
GWJ Thread ISO228 G2, 316L, flush-mounted
UBJ
Thread ISO228 G1/2, PN160.316L, separator, EN837, welded
UCJ
Thread ANSI MNPT1/2,PN160.316L,separator, welded
UDJ
Thread ISO228 G1/2, 316L, separator, EN837, threaded
UEJ
Thread ANSI MNPT1/2, 316L, separator, threaded
UGJ
Thread FNPT1/2, PN250, 316L, separator, threaded
UHJ
Thread FNPT1, PN250, 316L, separator, threaded
U5C Thread ANSI MNPT1, AlloyC, flush-mounted
U5J
Thread ANSI MNPT1, 316L, flush-mounted
U7C Thread ANSI MNPT1-1/2, AlloyC, fm=flush-mounted
U7J
Thread ANSI MNPT1-1/2, 316L, flush-mounted
U8C Thread ANSI MNPT2, AlloyC, flush-mounted
U8J
Thread ANSI MNPT2, 316L, flush-mounted
Endress+Hauser
81
Cerabar M PMC51, PMP51, PMP55
PMP55 (continued)
110
Process connection:
Pipe diaphragm seal
SIJ
Tri-Clamp ISO2852 DN10 (3/4") RDM, 316L, 3A, RDM = pipe diaphragm seal
SJJ
Tri-Clamp ISO2852 DN16 (3/4") RDM, 316L, 3A, RDM = pipe diaphragm seal
SBJ
Tri-Clamp ISO2852 DN25 (1") RDM, 316L, 3A, RDM = pipe diaphragm seal
SCJ
Tri-Clamp ISO2852 DN38 (1-1/2") RDM, 3A, 316L, PED Cat.II, RDM = pipe diaphragm seal
3.1 material + pressure test PED Cat.II
SDJ
Tri-Clamp ISO2852 DN51 (2") RDM, 316L, 3A, PED Cat.II, RDM = pipe diaphragm seal
3.1 material + pressure test PED Cat.II
SSJ
DIN11851 DN25 PN40, RDM, 316L, 3A, RDM = pipe diaphragm seal
STJ
DIN11851 DN32 PN40, RDM, 316L, 3A, RDM = pipe diaphragm seal
SUJ
DIN11851 DN40 PN40, RDM, 316L, 3A, RDM = pipe diaphragm seal
3.1 material + pressure test PED Cat.II
SZJ
DIN11851 DN50 PN25, RDM, 316L, 3A, RDM = pipe diaphragm seal
S4J
NEUMO BioControl D50 PN16, 316L, EHEDG, 3A
VAJ
DIN11864-1 A DN25 PN40, RDM, 316L, 3A, RDM = pipe diaphragm seal
VCJ
DIN11864-1 A DN40 PN40, RDM, 316L, 3A, RDM = pipe diaphragm seal
VDJ
DIN11864-1 A DN50 PN25, RDM, 316L, 3A, RDM = pipe diaphragm seal
Hygienic connections
MIJ
DIN11851 DN32 PN25 cap-nut, 316L, EHEDG, 3A
MRJ
DIN11851 DN50 PN25 cap-nut, 316L, EHEDG, 3A
MSJ
DIN11851 DN65 PN25 cap-nut, 316L, EHEDG, 3A
MTJ
DIN11851 DN80 PN25 cap-nut, 316L, EHEDG, 3A
MZJ
DIN11851 DN40 PN25 cap-nut, 316L, EHEDG, 3A
NKJ
DIN11851 DN50 PN25 thread, 316L, EHEDG, 3A
NLJ
DIN11851 DN65 PN25 thread, 316L, EHEDG, 3A
NMJ DIN11851 DN80 PN25 thread, 316L, EHEDG, 3A
NCJ
DIN11864-1 A DN40 PN16 tube DIN11866-1, 316L, EHEDG, 3A
NDJ
DIN11864-1 A DN50 PN16 tube DIN11866-1, 316L, EHEDG, 3A
NFJ
DIN11864-2 A DN32 PN16 tube DIN11866-1, 316L, EHEDG, 3A
NXJ
DIN11864-2 A DN40 PN16 tube DIN11866-1, 316L, EHEDG, 3A
NZJ
DIN11864-2 A DN50 PN16 tube DIN11866-1, 316L, EHEDG, 3A
S4J
NEUMO BioControl D50 PN16, 316L, EHEDG, 3A
TCJ
Tri-Clamp ISO2852 DN25 (1"), 316L, DIN32676 DN25, EHEDG, 3A, ASME-BPE
TJJ
Tri-Clamp ISO2852 DN38 (1-1/2"), 316L, DIN32676 DN40, EHEDG, 3A, ASME-BPE
TDJ
Tri-Clamp ISO2852 DN51 (2"), 316L, DIN32676 DN50, EHEDG, 3A, ASME-BPE
TFJ
Tri-Clamp ISO2852 DN76.1 (3"), 316L, EHEDG, 3A, ASME-BPE
TIJ
DRD DN50 65mm PN25, 316L
TQJ
Varivent F pipe DN25-32 PN40, 316L, EHEDG, 3A
TRJ
Varivent N pipe DN40-162 PN40, 316L, EHEDG, 3A
T0J
APV-RJT 1" PN40, 316L, 3A
T1J
APV-RJT 1-1/2" PN40, 316L, 3A
T2J
APV-RJT 2" PN40, 316L, 3A
T3J
APV-ISS 1" PN40, 316L, 3A
T4J
APV-ISS 1-1/2" PN40, 316L, 3A
T5J
APV-ISS 2" PN40, 316L, 3A
T6J
SMS 1” PN25, 316L, EHEDG, 3A
T7J
SMS 1-1/2” PN25, 316L, EHEDG, 3A
TXJ
SMS 2" PN25, 316L, EHEDG, 3A
YYY
Special version
170
Material of the process isolating diaphragm:
A
B
C
D
M
R
S
Y
180
Fill fluid:
1
2
4
5
6
9
82
316L
AlloyC
Monel
Tantalum
Rhodium>gold>316L
0.09mm PTFE>316L, not for vacuum
0.25mm PTFE>316L, not for vacuum
Special version
Silicone oil
Inert oil
Vegetable oil, FDA
High-temperature oil
Low-temperature oil
Special version
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
PMP55 (continued)
200
Diaphragm seal connection:
A
B
D
E
Y
Direct
Temperature isolator
..... m capillary
..... ft capillary
Special version
Additional ordering information (optional)
500
Operating language:
AA
AB
AC
AD
AE
AF
AK
AL
550
Calibration:
F1
F2
570
Cable PE, 2m/80inch + housing mounting bracket, wall/pipe, 304
Cable PE, 5m/200inch + housing mounting bracket, wall/pipe, 304
Cable PE, 10m/400inch + housing mounting bracket, wall/pipe, 304
Cable FEP, 5m/200inch IP69K + housing mounting bracket, wall/pipe, 304
Add-on mounted:
NA
Endress+Hauser
CoC Certificate of Compliance
Separate housing:
MA
MB
MC
MH
610
EN10204-3.1 wetted material, inspection certificate
NACE MR0175 wetted
EN10204-3.1 wetted material + AD2000 pressurized
EN10204-3.1 wetted material + Ra, (Ra= surface roughness), dimensional check, inspection certificate
EN10204-3.1 helium leak test, inspection certificate
EN10204-3.1 pressure test, inspection certificate
EN10204-3.1 measurement Delta ferrite content, inspection certificate
EN10204-3.1 PMI test (PMI = positive material identification), inspection certificate
Special version
Other approvals:
LW
600
Oil and grease removed
Cleaned for oxygen service
Cleaned for silicone-free applications
Diaphragm seal vacuum service
Surface quality Ra<0.38um electropolished (wetted)
Configured min alarm current
Configured HART Burst Mode PV
Special version
Test, certificate:
JA
JB
JF
KB
KD
KE
KF
KG
K9
590
Factory calibration certificate, 5-point
DKD calibration certificate 10-point
Service:
HA
HB
HC
HG
HK
IA
IB
I9
580
English
German
French
Spanish
Italian
Dutch
Chinese
Japanese
Overvoltage protection
83
Cerabar M PMC51, PMP51, PMP55
PMP55 (continued)
620
Accessory enclosed
PA
P2
P4
QA
QB
QC
QJ
QK
QL
QP
QR
QS
RL
RM
RN
850
Mounting bracket, wall/pipe, 30
Shutoff valve (PZAV), see additional spec
-R1A1 PZAV-R1A1 Shutoff valve, G1/2, C22.8
-R1A2 PZAV-R1A2 Shutoff valve, G1/2, 316Ti
-R1D1 PZAV-R1D1 Shutoff valve, NPT1/2, C22.8
-R1D2 PZAV-R1D2 Shutoff valve, NPT1/2, 316Ti
-B1A2 PZAV-B1A2 Shutoff valve., G1/2, 316Ti, 3.1
-B1D2 PZAV-B1D2 Shutoff valve., NPT1/2, 316Ti, 3.1
Siphon (PZW), see additional spec
-RA21 PZW-RA21 Siphon G1/2 vertical, C22.8
-RA22 PZW-RA22 Siphon G1/2 vertical, 316Ti
-RC11 PZW-RC11 Siphon G1/2 x weld. horiz. C22.8
-RD11 PZW-RD11 Siphon NPT1/2 x weld. horiz. C22.8
-BB22 PZW-BB22 Siphon NPT1/2 vertical, 316Ti, 3.1
-BA22 PZW-BA22 Siphon NPT1/2x weld.vert.316Ti 3.1
Welding neck G1/2, 316L
Welding neck G1/2, 316L, 3.1, EN10204-3.1 material, inspection certificat
Weld-in tool adapter G1/2, bras
Welding neck G1-1/2, 316
Welding neck G1-1/2, 316L, 3.1, EN10204-3.1 material, inspection certificat
Weld-in tool adapter G1-1/2, bras
Welding flange DRD DN50 65mm, 316
Welding fl. DRD DN50 65mm, 316L 3.1, EN10204-3.1 material, inspection certificat
Weld-in tool flange DRD DN50 65mm, bras
Plug-in jack M1
Plug-in jack M12, 90de
Plug-in jack M12, 90deg+5m cabl
Software version:
78
895
01.00.zz, HART, DevRev01
Identification:
Z1
Z2
Measuring point (TAG)
Bus address
You can enter the versions for the specific feature in the following table. The versions entered make up the
complete order code.
10
20
30
40
50
70
80
90
110
170
180
200
500
550
570
580
590
600
610
620
850 895
PMP55 -
84
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Documentation
Technical Information
• EMC test procedures TI241F/00/en
• Deltabar M: TI434P/00/en
• Deltapilot M: TI437P/00/en
Operating Instructions
4...20 mA Analog:
• Cerabar M: BA385P/00/en
4 to 20 mA HART:
• Cerabar M, Deltabar M, Deltapilot M: BA382P/00/en
Field Xpert: BA060S/04/en
Brief Operating Instructions
4...20 mA Analog:
• KA1036P/00/en
4 to 20 mA HART:
• Cerabar M: KA1030P/00/en
Safety Instructions
Authorities Version in the
order code
Approval
Category
BA
Ex ia IIC
II 1/2 G
BB
Ex t IIC
BC
Type
Housing
Electronics
Documentation
F31
F15
PMC51, PMP51, PMP55
X
X
– 4 to 20 mA HART – XA464P
II 1/2 D
PMP51, PMP55
X
X
– 4 to 20 mA HART – XA466P
Ex d
II 2 G
PMP51, PMP55
X
---
– 4 to 20 mA HART – XA467P
BD
Ex nA
II 3 G
PMC51, PMP51, PMP55
X
X
– 4 to 20 mA HART – XA469P
BE
Ex ia IIC
II 2 G
PMC51, PMP51, PMP55
X
X
– 4 to 20 mA HART – XA464P
BF
Ex ia IIC
II 1/2 D
PMC51
X
X
– 4 to 20 mA HART – XA465P
BG
Ex ic IIC
II 3 G
PMC51, PMP51, PMP55
X
X
– 4 to 20 mA HART – XA489P
B1
Ex ia
Ex ia IIIC
II 1/2 G
II 1/2 D
PMC51, PMP51, PMP55
X
X
– 4 to 20 mA HART – XA468P
B2
Ex ia IIC
II 2 G
II 1/2 G
PMP51, PMP55
X
X
– 4 to 20 mA HART – XA468P
Authorities Version in the
order code
Approval
EPL
Type
Housing
IA
Ex ia IIC
Ga/Gb
IB
Ex d IIC
ID
ATEX
IECEx
Electronics
Documentation
F31
F15
PMC51, PMP51, PMP55
X
X
– 4 to 20 mA HART – XA470P
Gb
PMP51, PMP55
X
---
– 4 to 20 mA HART – XA471P
Ex t IIIC
Da/Db
PMP51, PMP55
X
X
– 4 to 20 mA HART – XA472P
IE
Ex ic
Gc
PMC51, PMP51, PMP55
X
X
– 4 to 20 mA HART – XA488P
IF
Ex ia IIIC
Da/Db
PMC51
X
X
– 4 to 20 mA HART – XA487P
I1
Ex ia IIC
Ex ia IIIC
Ga/Gb
Da/Db
PMC51, PMP51, PMP55
X
X
– 4 to 20 mA HART – XA473P
Endress+Hauser
85
Cerabar M PMC51, PMP51, PMP55
Installation/Control Drawings
Authorities Version in the Approval
order code
FA
FM
FM IS Cl.I,II,III Div.1 Gr.A-G, AEx ia
FM NI Cl.I Div.2 Gr.A-D,
FM IS: Zone 0,1,2,20,21,22/FM NI: Zone 2
Type
PMC51, PMP51, PMP55
Housing
Electronics
Documentation
F31
F15
X
X
– 4 to 20 mA HART – ZD235P
X
---
– 4...20 mA HART
– In preparation
X
– 4...20 mA HART
– In preparation
– 4...20 mA HART
– In preparation
FB
FM XP Cl.I, II Div.1 Gr.A-D, AEx d
(Factory sealed) Zone 1,2
PMP51, PMP55
FC
FM DIP Cl.II, III Div.1 Gr.A-D Zone 21,22
PMP51, PMP55
X
F1
FM IS/XP Cl.I, II Div.1 Gr.A-G, Zone 1,2
PMP51, PMP55
X
CA
C/US IS Cl.I,II,III Div.1 Gr.A-G,
C/US IS Cl.I Div.2 Gr.A-D, Ex ia
PMC51, PMP51, PMP55
X
X
– 4 to 20 mA HART – ZD238P
X
---
– 4...20 mA HART
– In preparation
X
X
– 4...20 mA HART
– In preparation
X
---
– 4...20 mA HART
– In preparation
X
---
– 4...20 mA HART
– In preparation
CB
CSA C/US CP Cl.I, II Div.1 Gr.B-G, Ex d
(factory sealed) Zone 1,2
PMP51, PMP55
CC
CSA C/US Cl.II, III Div.1 Gr.E-G, Zone
21,22
PMP51, PMP55
C1
CSA C/US IS/XP CL.I, II Div.1 Gr.A-G/B-G, PMP51, PMP55
Zone 1,2
8B
FM/CSA IS + XP Cl.I, II Div.1 Gr.A-D/B-G
FM IS/FM XP Cl.I, II Div.1 Gr.A-G+
CSA IS/XP Cl.I, II Div.1 Gr.A-G, Zone 1,2
CSA
FM
CSA
86
PMP55
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Accessories
Shutoff valve
G1/2
1/2 NPT
Ø 63
100
20
Ø 63
105
1/2 NPT
G1/2
79
79
P01-xMx5xxxx-06-xx-xx-xx-001
Max. working pressure [bar (psi)]
Connection thread [d]
Material
Version in the order code 1)
C22.8
R1A1
316Ti
R1A2, B1A2
C22.8
R1D1
316Ti
R1D2, B1D2
G1/2
400 (5800)
NPT1/2
1)
See also  ä 69 ff, feature 620, "Accessory enclosed", version "P2".
Siphon
G1/2
1
G1/2
2
SW27
SW27
1/2NPT
Ø 20
95
130
1/2NPT
Ø
275
56
145
110
56
G1/2
P01-xMx5xxxx-06-xx-xx-xx-001
No Max. working pressure [bar (psi)]
Material
Version in the order code 1)
C22.8
RA21
316Ti
RA22, BA22
NPT1/2
316Ti
BB22
G1/2
C22.8
RC11
NPT1/2
C22.8
RD11
Connection thread [d]
1
G1/2
100 (1500)
2
Max. operating temperature 120°C (248°F) in front of the siphon
1)
Endress+Hauser
See also  ä 69 ff, feature 620, "Accessory enclosed", version "P4".
87
Cerabar M PMC51, PMP51, PMP55
Welding necks and Weld-in
tool flanges
1.5
Ø 65
G1 1/2A
G1
Ø36
Ø50
Ø35.6
Ø 50
G1/2
Ø18,05
21
13
27.5
25
P01-PMx5xxxx-06-xx-xx-xx-004
Typ
G1/2, flush
mounted
P01-PMx5xxxx-06-xx-xx-xx-006
G1,
flush mounted
(metal sealing tape)
Material
Order
P01-PMx5xxxx-06-xx-xx-xx-005
G1-1/2, flush
mounted
316L
 ä 69 ff, feature 620, "Accessory enclosed", versions see folowing table
rows
PMC51
---
---
QJ / QK
PMP51
QA / QB
QE / QF
QJ / QK
PMP55
QA / QB
---
QJ / QK
Weld-in tool adapters
Werkstoff
brass
PMC51
---
---
QL
PMP51
QC
QG
QL
PMP55
QC
---
QL
M 10
P01-PMx5xxxx-06-xx-xx-xx-008
Typ
Uni D65
Material
Order
PMP55
P01-PMx5xxxx-06-xx-xx-xx-009
Uni D85
Ø125
Ø105
Ø 66
Ø 50
Ø 85
Rd 52 x 1/6
Ø 44
39.5
Ø 65
Rd 52 x 1/6
Ø 44
39.5
30°
20
15
12
≤17
P01-PMx5xxxx-06-xx-xx-xx-010
DRD DN50
316L
 ä 69 ff, feature 620, "Accessory enclosed", versions see folowing table
rows
---
---
QP / QR
Weld-in tool adapters
Material
PMP55
88
brass
---
---
QS
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Mounting bracket for wall and
pipe mounting
 ä 20 ff
M12 connector
 ä 13 ff
Endress+Hauser
89
Cerabar M PMC51, PMP51, PMP55
Configuration data sheet (HART)
Level
The following configuration data sheet has to be filled in and included with the order if the version
"K - Customized level" has been selected in feature 90 "Calibration; unit" in the product structure.
Pressure Engineering Unit
mbar
bar
psi
mmH2O
mH2O
ftH2O
inH2O
mmHg
Pa
kgf/cm2
kPa
MPa
Output Unit (Scaled unit)
%
m
dm
cm
mm
inch
ft
Empty calibration (a)
(Empty) low pressure value
l
hl
gal
Igal
m3
ft3
in3
(Empty) low level value
[pres. eng. unit]
Full calibration (a)
(Full) high pressure value
Damping
[Scaled Unit]
(Full) high level value
[pres. eng. unit]
Display Information
1st Value Display
Measured Value (PV)
kg
t
lb
2nd Value Display
(factory setting)
None
Pressure
Current [mA] (HART only)
Temperature
Measured value (%)
[Scaled Unit]
300 mbar
3m
(b)
0 mbar
0m
(a)
Damping: ____ sec
P01-PMX5xxxx-16-xx-xx-en-000
90
Endress+Hauser
Cerabar M PMC51, PMP51, PMP55
Pressure
The following configuration data sheet has to be filled in and included with the order if the version
"J - Customized pressure" has been selected in feature 90 "Calibration; unit" in the product structure.
Pressure Engineerung Unit (a)
mbar
bar
psi
mmH2O
mH2O
ftH2O
inH2O
mmHg
Pa
2
kgf/cm
kPa
MPa
Factory setting: mbar/bar, depenging on measuring cell
Calibration Range / Output
LRV: _____________________ [pressure engineering unit)
URV: _____________________ [pressure engineering unit)
Display Information
1st Value Display
Main Value
Damping
2nd Value display
None
(factory setting)
Pressure
Current [mA] (HART only)
Temperature
Measured value (%)
Damping: ____ sec (Factory setting: 2 sec)
P01-xxxxxxxx-16-xx-xx-xx-001
Endress+Hauser
91
Cerabar M PMC51, PMP51, PMP55
Instruments International
Endress+Hauser
Instruments International AG
Kaegenstrasse 2
4153 Reinach
Switzerland
Tel. +41 61 715 81 00
Fax +41 61 715 25 00
www.endress.com
info@ii.endress.com
TI436P/00/EN/10.09(b)
No. 71103453
CCS/FM+SGML 6.0
71103453
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising