JBL VP7212MDP - JBL Pro Service

JBL VP7212MDP - JBL Pro Service
JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A.
Technical Manual
JBL
VP7212MDP
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
SYSTEM CONT’D:
•
•
•
•
•
•
• User Controls:
Frequency Response:
Frequency Range:
Maximum Peak Output:
Coverage Pattern:
Directivity Factor (Q):
Directivity Index (DL):
80 Hz – 18 kHz (±3 dB)
55 Hz – 20 kHz (–10 dB)
134 dB SPL 1m
90º x 50° rotatable waveguide
12.6
11 dB
TRANSDUCER SECTION:
• Cabinet:
• Grille:
• Low Frequency Driver:
Enclosure (Not for Sale)
363498-001
2262FF, 304mm (12 in) dia., 76mm
(3 in) Dual Coil neodymium Differential
Drive, Direct Cooled
• Bandpass Nominal Impedance: 2 x 2 ohms
• High Frequency Driver:
2452H-SL, 100mm (4 in) titanium
amped diaphragm, 1.5 in exit
• Bandpass Nominal Impedance: 8 Ohms
SYSTEM:
• DPC1 Internal Amplification
Output (at nominal load):
• DPC1 Output:
• DPC1 Output Section:
HF: Bridged Class D
• Audio Input Connector:
PACKAGE
1750W Peak, 875W Continuous
•
•
•
•
•
•
•
System EQ Selection: Full Range or
Speech / Vocal 0-16 dB input
Attenuator w/ 32 precision 0.5 dB steps
Signal Processing:
DSP based, resident in Input Module
System Management:
DSP based limiters for mechanical
and thermal protection
AC Power Operating Range: 90-132 VAC / 216-264 VAC,
50/60 Hz
AC Line Voltage:
50/60 Hz, Auto-Detect; 120V/240V
(-15%, +10%)
AC Input Connector:
Neutrik PowerCon (NAC 3MPA)
AC Look-thru:
Neutrik PowerCon (NAC 3MPB)
AC Current Requirement:
6A/system at 120V, 3A/system at 240V
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test:
B. L.F. Aural Sweep Test:
C. H.F. Aural Sweep Test:
150mV Input, 20 Hz to 20 kHz
4.0V Input, 20 Hz to 1.2 kHz
2.5V Input, 300 Hz to 20 kHz
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions:
346 x 565 x 413 mm
(Height x Width x Depth)
13.6 x 22.3 x 16.2 in
750 LF / 125 HF Watts (Continuous IEC
20.7 kg (45.5 lb)
shaped pink noise rated load impedance) • Net Weight:
LF: Dual Bridge Technology, Class D
WARRANTY INFORMATION:
XLR with loop-through
Owners Manual
363642-003
Carton
363940-001
Filler (2)
363942-001
363942-002
Package, Microfoam (2)
49790P
20” x 18” Sheets
Power Cord Assy Pack
355040 -002
• Refer to Warranty Statement packed with each product.
WIRING DIAGRAM
Driver, Low Frequency
2262FF
(363946-001X )
Cone Repl
C2X2R2262
Driver, High Frequency
2452H-SL
(352328-003X)
Diaph Repl
D8R2452-SL
Yel/Blk
Yel
Blu/Blk
Wire Harness
363640-001
Blu
Grn
Grn/Blk
JBL VP7212MDP REV G
SCHEMATIC
11-11
COMPONENT EXPLODED VIEW
High Freq Driver
352328-003X
2452H-SL
Diaph Repl
D8R2452-SL
Screw (4)
705-90002-16
1/4-20 x 1,
SKT SET, BLK
Washer (4)
705-90002-16
5/16 x .08
FLT PLREGBLK
ZINC, CS
Nut (4)
834-30010-00
1/4-20 x 1,
KEPS, BLK ZINC,
LCS, RIGHT
Threadlock
352951-001
9 GRAM STICK,
LOCTITE 248
Gasket
351577-001
6.5 x 12
Grille
363498-001
Screw (4)
804-51110-40
10-32 x 2 1/2,
OVAL, PH, BLK
ZINC, LCS
T-Nut (10)
352214-001
10-32 x 1/4
Zinc Plated
Amp Board
w/Modulator PCB
5009377
Gasket
339391-001
Rear 12”
Input Board
5009379
Interface PCB
5009378
Low Frequency Driver
2262FF
(363946-001X)
Cone Repl
C2X2R2262
Screw (10)
804-01110-16
10-32 x 1,
FIL, PH,
BLK ZINC, LCS
Dome
71646-06
Wire Harness
363640-001
Screw, Grille (10)
804-51110-12
10-32 x 3/4
OVAL, PH, BLK
ZINC, LCS SCR,
AMP
Amplifier Trim
363560-001
Waveguide
338650-001
Grille Support (2)
363090-001
Enclosure Assembly
VP7212-MDP
(Not Available for Sale)
Handle Backing
Plate (4)
363614-001
Small
Handle Assembly (2)
363366-001
Small
Screw (8)
883-011100-08
8 x 1/2
FLT, PH, PB,
CLR ZINC, LCS
JBL VP7212MDP
6
JBL VP7212MDP
Screw (10)
804-41110-20
10-32 x 1 1/4,
PAN, PH,
BLK ZINC, LCS
SCR HORN
T-Nut (16)
61861
10-32 x 7/16
Screw (20)
803-51010-16
8-32 x 1,
OVAL, PH,
BLK ZINC, LCS
SCR HANDLE
Foam Strip (2)
363943-002
Grille
Front Baffle
363083-001
Screw (10)
804-11110-16
10-32 x 1,
FLT, PH,
BLK ZINC, LCS
Gasket (2)
363944-002
Baffle/Sub-Baffle
Sub Baffle
363084-001
T-Nut (16)
61861
10-32 x 7/16
Step Barrel
T-Nut (8)
61860
Foot (4)
8-32 x 11/32
353445-001
Handle
Screw (4)
804-41110-12
10-32 x 3/4
PAN, PH, BLK
ZINC, LC SCR, FEET
JBL VP7212MDP
AMPLIFIER ASSEMBLY
363679-003
Amp Board
w/Modulator PCB
5009377
Input Label
364076-001
Warning Label
362965-001
Knob, Volume, dbx
DPIP Vert.
355039-003
Input Board
5009379
Interface PCB
5009378
Crown Amp Logo Badge
362969-001
Top Label
364075-002
JBL VP7212MDP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising