MODEL NO. MC175H42ST (MC175H42STA) 17.5 HP 42 Inch Lawn Tractor For Parts and Service, contact our authorized distributor: call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886 193194 Rev. 1 09.20.04 MH/TR PRINTED IN U.S.A. SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. • • • WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. • • WARNING: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor. • • • I. GENERAL OPERATION • • • • • • • • • • • Read, understand, and follow all instructions on the machine and in the manual before starting. Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades. Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area. Never carry passengers. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces. Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working. Slow down before turning. Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge guard. Operate machine only in daylight or good artificial light. Do not operate the machine while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways. Use extra care when loading or unloading the machine into a trailer or truck. Always wear eye protection when operating machine. Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury. Follow the manufacturer's recommendation for wheel weights or counterweights. Keep machine free of grass , leaves or other debris build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause build-up to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage. II. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. • Mow up and down slopes, not across. • Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles. • Choose a low ground speed so that you will not have to stop or shift while on the slope. • Do not mow on wet grass. Tires may lose traction. Always keep the machine in gear when going down slopes. Do not shift to neutral and coast downhill. • Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope. • Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause the machine to roll over. • Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine. Do no use on steep slopes. • Do not try to stabilize the machine by putting your foot on the ground. • Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in. 2 SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN GENERAL SERVICE • Never operate machine in a closed are. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage and remove any fuelsoaked debris. Allow machine to cool before storing. • If you strike a foreign object, stop and inspect the machine. Repair, if necessary, before restarting. • Never make any adjustments or repairs with the engine running. • Check grass catcher components and the discharge guard frequently and replace with manufacturer's recommended parts, when necessary. • Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. Adjust and service as required. • Maintain or replace safety and instruction labels, as necessary. Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. • Be alert and turn machine off if a child enters the area. • Before and while backing, look behind and down for small children. • Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine. • Never allow children to operate the machine. • Use extra care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child. IV. TOWING • • • • • Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the hitch point. Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes. Never allow children or others in or on towed equipment. On slopes, the weight of the towed equipment may cause loss of traction and loss of control. Travel slowly and allow extra distance to stop. • • • V. SERVICE SAFE HANDLING OF GASOLINE To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. • Extinguish all cigarettes, cigars, pipes, and other sources of ignition. • Use only approved gasoline container. • Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. • Never fuel the machine indoors. • Never store the machine or fuel container where there is an open flame, spark, or pilot light such as on a water heater or other appliances. • Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from your vehicle when filling. • Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device. • If fuel is spilled on clothing, change clothing immediately. • Never overfill fuel tank. Replace gas cap and tighten securely. • • • • • • • • • 3 Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area. Never carry passengers. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine. Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. Be alert and turn machine off if a child enters the area. Before and while backing, look behind and down for small children. Mow up and down slopes (15° Max), not across. Choose a low ground speed so that you will not have to stop or shift while on the slope. Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope. If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/ department. We have competent, well-trained technicians and the proper tools to ser vice or repair this tractor. Please read and retain this manual. The instructions will enable you to assemble and maintain your tractor properly. Always observe the “SAFETY RULES”. PRODUCT SPECIFICATIONS GASOLINE CAPACITY AND TYPE: OIL TYPE (API-SG-SL): OIL CAPACITY: SPARK PLUG: (GAP: .030") GROUND SPEED (MPH): TIRE PRESSURE: CHARGING SYSTEM: BATTERY: BLADE BOLT TORQUE: 2.0 GALLONS UNLEADED REGULAR SAE 30 (above 32°F) SAE 5W-30 (below 32°F) W/ FILTER 3.5 PINTS W/O FILTER 3.0 PINTS CHAMPION RC12YC FORWARD: 5.5 REVERSE: 2.4 FRONT: 14 PSI REAR: 10 PSI 3 AMPS BATTERY 5 AMPS HEADLIGHTS AMP/HR: 28 MIN. CCA: 230 CASE SIZE: U1R 27-35 FT. LBS. CUSTOMER RESPONSIBILITIES • • • Read and observe the safety rules. Follow a regular schedule in maintaining, caring for and using your tractor. Follow the instructions under “Maintenace” and “Storage” sections of this owner’s manual. WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. A spark arrester for the muffler is available through your nearest authorized service center/department (See REPAIR PARTS section of this manual). TABLE OF CONTENTS MAINTENANCE ..................................................... 15-18 SERVICE AND ADJUSTMENTS ............................ 19-23 STORAGE .................................................................... 24 TROUBLESHOOTING ............................................ 25-26 REPAIR PARTS - TRACTOR .................................. 28-41 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICATIONS ....................................... 4 CUSTOMER RESPONSIBILITIES................................. 4 ASSEMBLY ................................................................. 6-8 OPERATION ............................................................. 9-14 MAINTENANCE SCHEDULE ...................................... 15 4 UNASSEMBLED PARTS Steering Wheel Seat Steering Boot (1) Washer 17/32 x 1-3/16 x 12 Gauge Steering Wheel Insert Steering Extension Shaft (1) Knob Steering Wheel Adapter (1) Large Flat Washer Key (1) Locknut 1/2-20 (2) Keys (1) Oil Drain Tube Slope Sheet (1) Locknut 1/4-28 (1) Hex Bolt 1/4-28 x 1-1/4 5 ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY INSERT A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) 3/4" wrench Pliers (2) 7/16" wrenches Tire pressure gauge Utility knife When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel). 1/2 LOCK WASHER LARGE FLAT WASHER STEERING WHEEL TO REMOVE TRACTOR FROM CARTON STEERING BOOT UNPACK CARTON • • • Remove all accessible loose parts and parts cartons from carton. Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat. Check for any additional loose parts or cartons and remove. TABS EXTENSION SHAFT ADAPTER 1/4 HEX BOLT BEFORE REMOVING TRACTOR FROM SKID 1/4 LOCKNUT ATTACH STEERING WHEEL (See Fig. 1) ASSEMBLE EXTENSION SHAFT AND BOOT • Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely. 02 60 1 LOWER STEERING SHAFT TAB SLOTS IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE. • Place tabs of steering boot over tab slots in dash and push down to secure. FIG. 1 INSTALL STEERING WHEEL • Position front wheels of the tractor so they are pointing straight forward. • Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension. • Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter. • Assemble large flat washer, 1/2 hex nut and tighten securely. • Snap steering wheel insert into center of steering wheel. • Remove protective materials from tractor hood and grill. INSTALL SEAT (See Fig. 2) Adjust seat before tightening adjustment knob. • Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. • Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard. • Place seat on seat pan so head of shoulder bolts are positioned over the large slotted holes in pan. • Push down on seat to engage shoulder bolts in slots and pull seat towards rear of tractor. • Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten. • Lower seat into operating position and sit in seat. • Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. • Get off seat without moving its adjusted position. • Raise seat and tighten adjustment knob securely. IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID. 6 ASSEMBLY DISCARD TERMINAL PROTECTIVE CAPS SEAT KEPS NUT TERMINAL COVER HEX BOLT SEAT PAN 02617 SHOULDER BOLTS 02604 POSITIVE (RED) CABLE NEGATIVE (BLACK) CABLE FIG. 3 FLAT WASHER SEAT PAN 02615 LABEL ADJUSTMENT KNOB FIG. 2 CONNECT BATTERY (See Figs. 3 and 4) 02602 CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. FIG. 4 NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid. TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls) Positive terminal must be connected first to prevent sparking from accidental grounding. • • • • • • • Lift seat pan to raised position. Remove terminal protective caps and discard. If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in the Maintenance section of this manual for charging instructions). First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal. Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely. • • • Press lift lever plunger and raise attachment lift lever to its highest position. Release parking brake by depressing clutch/brake pedal. Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual). Roll tractor forward off skid. Remove banding holding the deflector shield up against tractor. TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of controls) 7 WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects. • Be sure all the above assembly steps have been completed. • Check engine oil level and fill fuel tank with gasoline. • Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual). ASSEMBLY • Sit on seat in operating position, depress clutch/brake pedal and set the parking brake. • Place motion control lever in neutral (N) position. • Press lift lever plunger and raise attachment lift lever to its highest position. • Start the engine. After engine has started, move throttle control to idle position. • Release parking brake. • Slowly move the motion control lever forward and slowly drive tractor off skid. • Apply brake to stop tractor, set parking brake and place motion control lever in neutral position. • Turn ignition key to "STOP" position. Continue with the instructions that follow. INSTALL MULCHER PLATE (See Fig. 5) (If previously removed) • • • • Raise and hold deflector shield in upright position. Place front of mulcher plate over front of mower deck opening and slide into place, as shown. Hook front latch into hole on front of mower deck. Hook rear latch into hole on back of mower deck. CAUTION: Do not remove deflector shield from mower. TO CONVERT DISCHARGING TO BAGGING OR Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory. NOTE: It is not necessary to change blades. The mulcher blades are designed for discharging and bagging also. DEFLECTOR SHIELD MULCHER PLATE LATCH HOOKS 01 23 3 FIG. 5 CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in “PRODUCT SPECIFICATIONS” section of this manual. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. CHECK FOR PROPER POSITION OF ALL BELTS See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly. CHECK BRAKE SYSTEM After you learn how to operate your tractor, check to see that the brake is properly adjusted. See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual. ✓CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in carton. ✓ Battery is properly prepared and charged. (Minimum 1 hour at 6 amps). ✓ Seat is adjusted comfortably and tightened securely. ✓ All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory). ✓ Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling). ✓ Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers. ✓ Check wiring. See that all connections are still secure and wires are properly clamped. ✓ Before driving tractor, be sure freewheel control is in drive position. WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS: ✓ Engine oil is at proper level. ✓ Fuel tank is filled with fresh, clean, regular unleaded gasoline. ✓ Become familiar with all controls - their location and function. Operate them before you start the engine. ✓ Be sure brake system is in safe operating condition. ✓ It is important to purge the transmission before operating your tractor for the first time. Follow proper starting and transmission purging instructions (See “TO START ENGINE” and “PURGE TRANSMISSION” in the Operation section of this manual). 8 OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITION P ENGINE OFF LIGHTS ON OVER TEMP LIGHT FUEL ENGINE ON OIL PRESSURE ENGINE START BATTERY PARKING BRAKE REVERSE FORWARD PARKING BRAKE LOCKED MOWER HEIGHT PARKING BRAKE UNLOCKED MOWER LIFT 15 ATTACHMENT CLUTCH ENGAGED ATTACHMENT CLUTCH DISENGAGED DANGER, KEEP HANDS AND FEET AWAY 15 SLOPE HAZARDS KEEP AREA CLEAR (SEE SAFETY RULES SECTION) DANGER indicates a hazard which, if not avoided, will result in death or serious injury. FREE WHEEL (Automatic Models only) Failure to follow instructions could result in serious injury or death. The safety alert symbol is used to identify safety information about hazards which can result in death, serious injury and/or property damage. WARNING indicates a hazard which, if not avoided, could result in death or serious injury. CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury. CAUTION when used without the alert symbol, indicates a situation that could result in damage to the tractor and/or engine. HOT SURFACES indicates a hazard which, if not avoided, could result in death, serious injury and/or property damage. FIRE indicates a hazard which, if not avoided, could result in death, serious injury and/or property damage. 9 OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. ATTACHMENT CLUTCH LEVER IGNITION SWITCH LIGHT SWITCH POSITION LIFT LEVER PLUNGER AMMETER THROTTLE/CHOKE CONTROL ATTACHMENT LIFT LEVER CLUTCH/BRAKE PEDAL MOWER DECK HEIGHT ADJUSTMENT INDICATOR PARKING BRAKE MOTION CONTROL LEVER FREE WHEEL CONTROL FIG. 6 Our tractors conform to the safety standards of the American National Standards Institute. IGNITION SWITCH - Used for starting and stopping the engine. LIFT LEVER PLUNGER - Used to release attachment lift lever when changing its position. LIGHT SWITCH POSITION - Turns the headlights on and off. MOTION CONTROL LEVER - Selects the speed and direction of tractor. PARKING BRAKE - Locks clutch/brake pedal into the brake position. THROTTLE/CHOKE CONTROL - Used for starting and controling engine speed. AMMETER - Indicates charging (+) or discharging (-) of battery. ATTACHMENT CLUTCH LEVER - Used to engage the mower blades, or other attachments mounted to your tractor. ATTACHMENT LIFT LEVER - Used to raise and lower the mower deck or other attachments mounted to your tractor. CLUTCH/BRAKE PEDAL - Used for declutching and braking the tractor and starting the engine. FREEWHEEL CONTROL - Disengages transmission for pushing or slowly towing the tractor with the engine off. 10 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas. HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE (See Fig. 7) Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. • Depress clutch/brake pedal into full “BRAKE” position and hold. • Place parking brake lever in “ENGAGED” position and release pressure from clutch/brake pedal. Pedal should remain in “BRAKE” position. Make sure parking brake will hold tractor secure. CAUTION: Always stop tractor completely, as described above, before leaving the operator's position; to empty grass catcher, etc. TO USE THROTTLE CONTROL (See Fig. 7) Always operate engine at full throttle. • Operating engine at less than full throttle reduces the battery charging rate. • Full throttle offers the best bagging and mower performance. ATTACHMENT CLUTCH LEVER "ENGAGED" POSITION THROTTLE/CHOKE CONTROL IGNITION KEY TO MOVE FORWARD AND BACKWARD (See Fig. 7) "DISENGAGED" POSITION CLUTCH/BRAKE PEDAL "DRIVE" POSITION The direction and speed of movement is controlled by the motion control lever. • Start tractor with motion control lever in neutral (N) position. • Release parking brake. • Slowly move motion control lever to desired position. PARKING BRAKE "ENGAGED" POSITION "BRAKE" POSITION MOTION CONTROL LEVER TO ADJUST MOWER CUTTING HEIGHT (See Fig. 7) PARKING BRAKE "DISENGAGED" POSITION The position of the attachment lift lever determines the cutting height. • Grasp lift lever. • Press plunger with thumb and move lever to desired position. The cutting height range is approximately 1-1/2 to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. • The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth. • For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height. FIG. 7 STOPPING (See Fig. 7) MOWER BLADES • To stop mower blades,move attachment clutch lever to “DISENGAGED” position. GROUND DRIVE • To stop ground drive, depress clutch/brake pedal into full “BRAKE” position. • Move motion control lever to neutral (N) position. IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED. ENGINE • Move throttle control between half and full speed (fast) position. NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping may cause engine to “backfire”. • Turn ignition key to “STOP” position and remove key. Always remove key when leaving tractor to prevent unauthorized use. • Never use choke to stop engine. IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD). TO ADJUST GAUGE WHEELS (See Fig. 8) 11 Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE:Adjust gauge wheels with tractor on a flat level surface. OPERATION • • • Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in the Operation section of this manual). With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely. Repeat for opposite side installing gauge wheel in same adjustment hole. TO OPERATE ON HILLS WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • • • • 3/8-16 LOCKNUT • Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills. If slowing is necessary, move throttle control lever to slower position. If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake. Move motion control lever to neutral (N) position. IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED. GAUGE WHEEL MOUNTING BRACKET 01 • 42 3 • • SHOULDER BOLT 3/8 WASHER GAUGE WHEEL To restart movement, slowly release parking brake and clutch/brake pedal. Slowly move motion control lever to slowest setting. Make all turns slowly. TO TRANSPORT (See Figs. 6 and 10) FIG. 8 When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. • Raise attachment lift to highest position with attachment lift control. • Pull freewheel control out and down into the slot and release so it is held in the disengaged position. • Do not push or tow tractor at more than two (2) MPH. • To reengage transmission, reverse above procedure. NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.). TO OPERATE MOWER (See Fig. 9) Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills. • Select desired height of cut. • Start mower blades by engaging attachment clutch control. • TO STOP MOWER BLADES - disengage attachment clutch control. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place. Transmission Engaged "ENGAGED" POSITION ATTACHMENT LIFT LEVER HIGH POSITION LOW POSITION Transmission Disengaged DEFLECTOR SHIELD FIG. 10 ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION FIG. 9 12 OPERATION • Place motion control lever in neutral (N) position. • Move attachment clutch to “DISENGAGED” position. • Move throttle control to choke position. NOTE: Before starting, read the warm and cold starting procedures below. • Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry. TOWING CARTS AND OTHER ATTACHMENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor. BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped, from the factory, already filled with summer weight oil. • Check engine oil with tractor on level ground. • Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill. • For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual). • To change engine oil, see the Maintenance section in this manual. WARM WEATHER STARTING (50° F and above) • When engine starts, move the throttle control to the fast position. • The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above. COLD WEATHER STARTING ( 50° F and below) • When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature. ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness. AUTOMATIC TRANSMISSION WARM UP • Before driving the unit in cold weather, the transmission should be warmed up as follows: • Be sure the tractor is on level ground. • Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position. • Allow one minute for transmission to warm up. This can be done during the engine warm up period. • The attachments can also be used during the engine warm-up period after the transmission has been warmed up. NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual. CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GAS O LINE TO HELP INSURE GOOD COLD WEATHER STARTING. CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is running. To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor. TO START ENGINE (See Fig. 6) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress clutch/brake pedal and set parking brake. IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR. • 13 Place tractor safely on level surface with engine off and parking brake set. OPERATION • Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual). • Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal. • Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times. NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system. • Move motion control lever to neutral (N) position. Shutoff engine and set parking brake. • Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this section of manual). • Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal. • Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times. • Your transmission is now purged and now ready for normal operation. • • • • MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN AFTER EACH USE. • • • MOWING TIPS • • • • If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the desired height. Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing. Always operate engine at full throttle when mowing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired. When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used. Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. The left hand side of mower should be used for trimming. Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting. When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 11). The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades. Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried, yet the newly cut area will not be exposed to direct sunlight. For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades (See Fig. 12). For extremely heavy mulching, reduce your width of cut on each pass and mow slowly. MAX 1/3 FIG. 12 • • FIG. 11 14 Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the first cut path. Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn. MAINTENANCE MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE E E S S RS AG US RS UR OUR OU SON OR U O H O H H A 0 ST E 8H SE RE 25 10 50 Y Y Y Y Y RE O R R R R R O F E E E E E F BE SERVICE EV EV EV EV EV BE H AC DATES Check Brake Operation Check Tire Pressure T R A C T 0 R Check Operator Presence and Interlock Systems Check for Loose Fasteners 5 Sharpen/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Check Transaxle Cooling Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) E N G I N E 1,2 Change Engine Oil (without oil filter) 1,2 Clean Air Filter 2 Clean Air Screen 2 Inspect Muffler/Spark Arrester Replace Oil Filter (If equipped) 1, 2 Clean Engine Cooling Fins 2 Replace Spark Plug Replace Air Filter Paper Cartridge 2 Replace Fuel Filter 3 - Replace blades more often when mowing in sandy soil. 4 - Not required if equipped with maintenance-free battery. 5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum. Do not overtighten. 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions. GENERAL RECOMMENDATIONS LUBRICATION CHART The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain tractor as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tractor. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. • At least once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer. ➀SPINDLE ZERK ➀FRONT WHEEL BEARING ZERK ➀SPINDLE ZERK ➀FRONT WHEEL BEARING ZERK ➁ENGINE BEFORE EACH USE • • • • • Check engine oil level. Check brake operation. Check tire pressure. Check operator presence and interlock systems for proper operation. Check for loose fasteners. ➀GENERAL PURPOSE GREASE ➁REFER TO MAINTENANCE “ENGINE” SECTION IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. 15 MAINTENANCE TRACTOR TRAILING EDGE UP Always observe safety rules when performing any maintenance. 4 21 01 BLADE MANDREL ASSEMBLY CENTER HOLE BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual). LOCK WASHER FLAT WASHER STAR BLADE BOLT TIRES • Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual). • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. FIG. 13 TO SHARPEN BLADE (See Fig. 14) NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine. • The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower. • To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer). NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not. • Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. OPERATOR PRESENCE SYSTEM Be sure operator presence and interlock systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position. • When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. • When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine. • The attachment clutch should never operate unless the operator is in the seat. CENTER HOLE 01 5/8" BOLT OR PIN BLADE CARE BLADE 20 2 For best results mower blades must be kept sharp. Replace bent or damaged blades. FIG. 14 BLADE REMOVAL (See Fig. 13) • • • BATTERY Raise mower to highest position to allow access to blades. Remove blade bolt, lock washer and flat washer securing blade. Install new or resharpened blade with trailing edge up towards deck as shown. Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY. • • Reassemble blade bolt, lock washer and flat washer in exact order as shown. Tighten blade bolt securely (27-35 Ft. Lbs. torque). IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS. 16 TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. MAINTENANCE • TO CHANGE ENGINE OIL (See Figs. 15 and 16) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. • Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil. • Remove yellow cap from end of drain valve and install the drain tube onto the fitting. Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. Rinse the battery with plain water and dry. Clean terminals and battery cable ends with wire brush until bright. Coat terminals with grease or petroleum jelly. Reinstall battery (See “CONNECT BATTERY” in the Assembly section of this manual). • • • • V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. OIL DRAIN VALVE TRANSAXLE COOLING DRAIN TUBE YELLOW CAP FIG. 16 TRANSAXLE PUMP FLUID • The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized ser vice center/department. • • ENGINE • LUBRICATION • Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. • SAE VISCOSITY GRADES SAE 30 5W-30 -20 F C -30 0 -20 30 -10 32 40 0 20 30 Unlock drain valve by pushing inward and turning counterclockwise. To open, pull out on the drain valve. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve. Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual. Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick. Tighten cap onto the tube securely when finished. CLEAN AIR SCREEN 100 80 60 10 3 46 02 CLOSED AND LOCKED POSITION The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transaxle. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. 40 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE FIG. 15 NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level. AIR FILTER Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See Engine Manual. ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. 17 MAINTENANCE CLEAN AIR INTAKE/COOLING AREAS CLEANING To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times. Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary. Make sure the cooling shrouds are reinstalled. NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating. See engine manual. • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower. MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual. IN-LINE FUEL FILTER (See Fig. 17) The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. • With engine cool, remove filter and plug fuel line sections. • Place new fuel filter in position in fuel line with arrow pointing towards carburetor. • Be sure there are no fuel line leaks and clamps are properly positioned. • Immediately wipe up any spilled gasoline. CLAMP CLAMP FUEL FILTER FIG. 17 18 SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress clutch/brake pedal fully and set parking brake. • Place motion control lever in neutral (N) position. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO INSTALL MOWER (See Fig. 18) TRACTOR • • TO REMOVE MOWER (See Fig. 18) Mower will be easier to remove from the right side of tractor. • Place attachment clutch in “DISENGAGED” position. • Move attachment lift lever forward to lower mower to its lowest position. • Roll belt off engine pulley. • Remove small retainer spring, and remove clutch spring off pulley bolt. • Remove large retainer spring, slide collar off and push housing guide out of bracket. • Disconnect anti-swaybar from chassis bracket by removing retainer spring. • Disconnect suspension arms from rear deck brackets by removing retainer springs. • Disconnect front links from deck by removing retainer springs. • Raise lift lever to raise suspension arms. Slide mower out from under tractor. • • • • • • • Raise attachment lift lever to its highest position. Slide mower under tractor with deflector shield to right side of tractor. Lower lift lever to its lowest position. Connect front links to mower deck and secure with retainer springs.. Connect suspension arms to rear deck brackets and secure with retainer springs. Connect anti-swaybar to chassis bracket and secure with retainer spring. Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring. Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring. Install belt onto engine pulley. TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower. IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO SQUARE HOLE IN FRAME. SMALL RETAINER SPRING CLUTCH SPRING FLAT WASHER SQUARE HOLE SMALL RETAINER SPRING SUSPENSION ARMS ENGINE PULLEY CLUTCH SPRING FRONT LINK RETAINER SPRING ANTI-SWAY BAR RETAINER SPRINGS (BOTH SIDES) COLLAR HOUSING GUIDE LARGE RETAINER SPRING BRACKET FIG. 18 19 DEFLECTOR SHIELD SERVICE AND ADJUSTMENTS SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20) • Raise mower to its highest position. • At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other. • If adjustment is necessary, make adjustment on one side of mower only. • To raise one side of mower, tighten lift link adjustment nut on that side. • To lower one side of mower, loosen lift link adjustment nut on that side. NOTE: Three full turns of adjustment nut will change mower height about 1/8". • Recheck measurements after adjusting. "D" GROUND LINE "D" FIG. 21 BOTH FRONT LINKS MUST BE EQUAL IN LENGTH NUT "F" BOTTOM EDGE OF MOWER TO GROUND BOTTOM EDGE OF MOWER TO GROUND “A” MANDREL NUT "E" TRUNNION “A” FIG. 19 FRONT LINKS SUSPENSION ARM FIG. 22 TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 23) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. LIFT LINK ADJUSTMENT NUT BELT REMOVAL • Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual). • Work belt off both mandrel pulleys and idler pulleys. • Pull belt away from mower. BELT INSTALLATION • Install new belt in reverse order of removal. • Make sure belt is in all pulley grooves and inside all belt guides. • Install mower in reverse order of removal instructions. FIG. 20 FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22) IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE. To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position. Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown. • Before making any necessary adjustments, check that both front links are equal in length. • If links are not equal in length, adjust one link to same length as other link. • To lower front of mower loosen nut “E” on both front links an equal number of turns. • When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links. • To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length. • When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links. • Recheck side-to-side adjustment. MANDREL PULLEY IDLER PULLEYS MANDREL PULLEY FIG. 23 TO CHECK AND ADJUST BRAKE (See Fig. 24) 20 Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle. If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. SERVICE AND ADJUSTMENTS • Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades. • Remove belt from center span keeper and pull belt away from tractor. BELT INSTALLATION • Carefully work new belt down around transmission cooling fan and onto the input pulley. • Slide belt into the center span keeper. • Pull belt toward front of tractor and roll around the top groove of engine pulley. • Install belt through stationary idler and clutching idler. • Make sure belt is in all pulley grooves and inside all belt guides and keepers. • Install mower (See “TO INSTALL MOWER” in this section of manual). TO CHECK BRAKE • Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake. • Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position. The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced. TO ADJUST BRAKE • Depress clutch/brake pedal all the way down and engage parking brake. • Measure distance between brake operating arm and nut “A” on brake rod. • If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”. • Engage transmission by placing freewheel control in “transmission engaged” position. • Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center. ENGINE PULLEY CLUTCHING IDLER STATIONARY IDLER TRANSMISSION INPUT PULLEY WITH PARKING BRAKE “ENGAGED” CENTER SPAN KEEPER NUT “A” 1-9/16” JAM NUT FIG. 25 TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26) OPERATING ARM DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUSTMENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT FIG. 24 TO REPLACE MOTION DRIVE BELT (See Fig. 25) Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL • Remove mower (See “TO REMOVE MOWER” in this section of manual). NOTE: Observe entire motion drive belt and position of all belt guides and keepers. • Remove belt from stationary idler and clutching idler. • Remove belt downward from around engine pulley. 21 The motion control lever has been preset at the factory and adjustment should not be necessary. • Loosen adjustment bolt in front of the right rear wheel, and lightly tighten. • Start engine and move motion control lever until tractor does not move forward or backward. • Hold motion control lever in that position and turn engine off. • While holding motion control lever in place, loosen the adjustment bolt. • Move motion control lever to the neutral (N) (lock gate) position. • Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position. After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps: • Loosen the adjustment bolt. • Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep. • Tighten adjustment bolt securely. • Start engine and test. • If tractor still creeps, repeat above steps until satisfied. SERVICE AND ADJUSTMENTS MOTION CONTROL LEVER TO START ENGINE WITH A WEAK BATTERY (See Fig. 28) NEUTRAL LOCK GATE WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. ADJUSTMENT BOLT If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of this manual). If “jumper cables” are used for emergency starting, follow this procedure: FIG. 26 TRANSMISSION REMOVAL/REPLACEMENT Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMISSION” in the Operation section of this manual. IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES. TO AD JUST STEER ING WHEEL ALIGNMENT TO ATTACH JUMPER CABLES • Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis. • Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery. • Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery. If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly section of this manual. FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department. TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully charged battery. • RED cable last from both batteries. TO REMOVE WHEEL FOR REPAIRS (See Fig. 27) • • Block up axle securely. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle. Insert square key. • Replace washers and snap retaining ring securely in axle groove. • Replace axle cover. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. WEAK OR DEAD BATTERY FULLY CHARGED BATTERY FIG. 28 TO REPLACE HEADLIGHT BULB • • WASHERS RETAINING RING • • AXLE COVER Raise hood. Pull bulb holder out of the hole in the backside of the grill. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. Close hood. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts section. SQUARE KEY (REAR WHEEL ONLY) FIG. 27 TO REPLACE FUSE 22 Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. SERVICE AND ADJUSTMENTS TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 29) ENGINE • • • TO ADJUST THROTTLE CONTROL CABLE • Raise hood. Unsnap headlight wire connector. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. To replace, reverse above procedure. The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual. TO ADJUST CHOKE CONTROL The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engne manual. HOOD TO ADJUST CARBURETOR Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment. HEADLIGHT WIRE CONNECTOR 02778 FIG. 29 23 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE. WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRACTOR • Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty. • Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. • Use fresh fuel next season. NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer. Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area. • Clean entire tractor (See “CLEANING” in the Maintenance section of this manual). • Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual). • Lubricate as shown in the Maintenance section of this manual. • Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. • Touch up all rusted or chipped paint surfaces; sand lightly before painting. ENGINE OIL Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual). BATTERY • • • • • CYLINDER(S) Fully charge the battery for storage. After a period of time in storage, battery may require recharging. To help prevent corrosion and power leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Maintenance section of this manual). After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals. If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces. • • • • Remove spark plug(s). Pour one ounce of oil through spark plug hole(s) into cylinder(s). Turn ignition key to “START” position for a few seconds to distribute oil. Replace with new spark plug(s). OTHER • • • • Do not store gasoline from one season to another. Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems. If possible, store your tractor indoors and cover it to give protection from dust and dirt. Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust. IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM. 24 TROUBLESHOOTING POINTS PROBLEM Will not start CAUSE 1. 2. 3. 4. 5. 6. 7. Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. 8. 9. Loose or damaged wiring. Carburetor out of adjustment. 8. 9. 10. Hard to start CORRECTION Engine valves out of adjustment. 10. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. Check all wiring. See “To Adjust Carburetor” in Service Adjustments section. Contact an authorized service center/department. 1. 2. 3. 4. 5. 6. 7. Dirty air filter. Bad spark plug. Weak or dead battery. Dirty fuel filter. Stale or dirty fuel. Loose or damaged wiring. Carburetor out of adjustment. 1. 2. 3. 4. 5. 6. 7. 8. Engine valves out of adjustment. 8. Clean/replace air filter. Replace spark plug. Recharge or replace battery. Replace fuel filter. Empty fuel tank and refill tank with fresh, clean gasoline. Check all wiring. See “To Adjust Carburetor” in Service Adjustments section. Contact an authorized service center/department. Engine will not turn over 1. 2. 3. 4. 5. 6. 7. 8. 9. Brake pedal not depressed. Attachment clutch is engaged. Weak or dead battery. Blown fuse. Corroded battery terminals. Loose or damaged wiring. Faulty ignition switch. Faulty solenoid or starter. Faulty operator presence switch(es). 1. 2. 3. 4. 5. 6. 7. 8. 9. Depress brake pedal. Disengage attachment clutch. Recharge or replace battery. Replace fuse. Clean battery terminals. Check all wiring. Check/replace ignition switch. Check/replace solenoid or starter. Contact an authorized service center/department. Engine clicks but will not start 1. 2. 3. 4. Weak or dead battery. Corroded battery terminals. Loose or damaged wiring. Faulty solenoid or starter. 1. 2. 3. 4. Recharge or replace battery. Clean battery terminals. Check all wiring. Check/replace solenoid or starter. Loss of power 1. 2. 3. 4. 5. 6. 7. 8. 9. Cutting too much grass/too fast. Throttle in “CHOKE” position. Build-up of grass, leaves and trash under mower. Dirty air filter. Low oil level/dirty oil. Faulty spark plug. Dirty fuel filter. Stale or dirty fuel. Water in fuel. 1. 2. 3. 4. 5. 6. 7. 8. 9. Raise cutting height/reduce speed. Adjust throttle control. Clean underside of mower housing. Clean/replace air filter. Check oil level/change oil. Clean and regap or change spark plug. Replace fuel filter. Empty fuel tank and refill tank with fresh, clean gasoline. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. Connect and tighten spark plug wire. Clean engine air screen/fins. Clean/replace muffler. Check all wiring. See “To Adjust Carburetor” in Service Adjustments section. Contact an authorized service center/department. Excessive vibration 10. 11. 12. 13. 14. Spark plug wire loose. Dirty engine air screen/fins. Dirty/clogged muffler. Loose or damaged wiring. Carburetor out of adjustment. 10. 11. 12. 13. 14. 15. Engine valves out of adjustment. 15. 1. 2. 3. Worn, bent or loose blade. Bent blade mandrel. Loose/damaged part(s). 1. 2. 3. 25 Replace blade. Tighten blade bolt. Replace blade mandrel. Tighten loose part(s). Replace damaged parts. TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, and trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. Replace blade. Tighten blade bolt. Level mower deck. Clean underside of mower housing. Replace blade mandrel. Clean around mandrels to open vent holes. Mower blades will not rotate 1. 2. 3. 4. Obstruction in clutch mechanism. Worn/damaged mower drive belt. Frozen idler pulley. Frozen blade mandrel. 1. 2. 3. 4. Remove obstruction. Replace mower drive belt. Replace idler pulley. Replace blade mandrel. Poor grass discharge 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Engine speed too slow. Travel speed too fast. Wet grass. Mower deck not level. Low/uneven tire air pressure. Worn, bent or loose blade. Buildup of grass, leaves and trash under mower. Mower drive belt worn. Blades improperly installed. Improper blades used. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Place throttle control in “FAST” position. Shift to slower speed. Allow grass to dry before mowing. Level mower deck. Check tires for proper air pressure. Replace/sharpen blade. Tighten blade bolt. Clean underside of mower housing. Replace mower drive belt. Reinstall blades sharp edge down. Replace with blades listed in this manual. Clean around mandrels to open vent holes. Headlight(s) not working (if so equipped) 1. 2. 3. 4. 5. Switch is “OFF”. Bulb(s) or lamp(s) burned out. Faulty light switch. Loose or damaged wiring. Blown fuse. 1. 2. 3. 4. 5. Turn switch “ON”. Replace bulb(s) or lamp(s). Check/replace light switch. Check wiring and connections. Replace fuse. Battery will not charge 1. 2. 3. 4. Bad battery cell(s). Poor cable connections. Faulty regulator (if so equipped). Faulty alternator. 1. 2. 3. 4. Replace battery. Check/clean all connections. Replace regulator. Replace alternator. Loss of drive 1. 2. 3. Freewheel control in “disengaged” position. Motion drive belt worn, damaged, or broken. Air trapped in transmission during shipment or servicing. 1. 2. 3. Place freewheel control in “engaged” position. Replace motion drive belt. Purge transmission. Engine “backfires” when turning engine “OFF” 1. Engine throttle control not set between half and full speed (fast) position before stopping engine. 1. Move throttle control between half and full speed (fast) position before stopping engine. 26 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 SCHEMATIC RED BLACK BATTERY RED A RED M FUSE AMMETER (OPTIONAL) STARTER BLACK WHITE SOLENOID RED B S G BLACK L M CLUTCH / BRAKE (PEDAL UP) A1 A2 WHITE SEAT SWITCH (NOT OCCUPIED) IGNITION SWITCH WHITE BLACK BLACK BLACK BLACK HOUR METER ATT'MENT CLUTCH (CLUTCH OFF) GROUNDING CONNECTOR (OPTIONAL) SPARK PLUG GAP (2 PLUGS ON TWIN CYL. ENGINES) IGNITION UNIT BLACK BLUE FUEL LINE CHARGING SYSTEM OUTPUT 3 AMP DC @ 3600 RPM FUEL SHUT-OFF SOLENOID (IF SO EQUIPPED) ORANGE BLACK 28 VOLTS AC MIN. @ 3600 RPM (CHARGING SYSTEM DISCONNECTED) RED LIGHTING SYSTEM OUTPUT 5 AMP AC @ 3600 RPM DIODE ALTERNATOR 14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF) NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST. BLACK BROWN HEADLIGHTS NON-REMOVABLE CONNECTIONS IGNITION SWITCH POSITION CIRCUIT OFF M+G+A1 RUN/LIGHT B+A1 RUN START B+A1 B + S + A1 “MAKE” NONE A2+L NONE NONE WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING. 02363 27 REMOVABLE CONNECTIONS TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 ELECTRICAL 90 22 21 42 24 41 43 27 27 40 26 27 27 25 16 16 33 30 D.C .A MP ER 52 ES 29 45 8 28 27 55 179720 2 1 28 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 ELECTRICAL KEY NO. PART NO. DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 17 66-89 Box Battery 16 532 17 61-38 Switch Interlock Push-In 21 532 18 37-59 Harness Asm Light W/4152j 22 532 00 41-52 Bulb Light #1156 24 532 12 47-80 Cable Battery 6 Ga. 11" red 25 532 14 61-47 Cable Battery 6 Ga. 44" red w/16 wire 26 532 17 51-58 Fuse 20 AMP 27 873 51 04-00 Nut Keps Hex 1/4-20 unc 28 532 12 47-73 Cable Ground black 29 532 12 13-05 Switch Plunger Nc Gray 30 532 17 55-66 Switch Ign 33 532 14 04-01 Key Ign Molded Generic 40 532 17 97-20 Harness Ign. 41 871 11 04-08 Bolt Blk Fin Hex 1/4 - 20 x 1/2 42 532 13 15-63 Cover Terminal Red 43 532 17 88-61 Solenoid 48 532 12 14-33 Ammeter 52 532 14 19-40 Protection Wire Loop 90 532 18 04-49 Cover Terminal Battery NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm. 29 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 CHASSIS AND ENCLOSURES 259 264 258 28 263 17 261 10 39 18 10 30 58 278 31 209 5 159 5 209 11 208 9 209 208 207 64 209 26 142 60 1 144 13 26 143 144 60 142 209 2 26 26 145 37 37 14 74 206 208 38 209 38 14 chassis_elite sv_pro_11 30 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 CHASSIS AND ENCLOSURES KEY NO. PART NO. DESCRIPTION 1 532 17 46-19 Chassis Stamping 2 532 17 65-54 Drawbar 5 532 15 52-72 Bumper Hood/Dash 9 532 19 32-65 Dash 10 872 14 06-08 Bolt Carriage 3/8-16 x 1 11 532 17 49-96 Panel Dash Lh 13 532 18 69-52 Panel Dash Rh 14 817 49 06-08 Screw Thdrol 3/8-16 x 1/2 17 532 18 65-80 Hood 18 532 18 49-21 Bumper Hood 26 873 80 06-00 Nut Lock Hex W/Ins 3/8-16 unc 28 532 18 82-24 Grille/Lens Asm. (Includes Key Nos. 212 and 258 thru 261) 30 532 19 22-58 Fender Footrest STLT Pnt 31 532 13 99-76 Bracket Support Fender 37 817 49 05-08 Screw Thdrol 5/16-18 x 1/2 TYT 38 532 17 57-10 Bracket Asm Pivot Mower Rear 39 532 17 47-14 Bracket Pivot 58 532 15 01-27 Air Duct Engine 60 872 14 06-06 Bolt Rdhd Sqnk 3/8-16 unc x 3/4 64 532 15 47-98 Dash Lower STLT 74 873 68 06-00 Nut Crownlock 3/8-16 unc 142 532 17 57-02 Plate Reinforcement STLT 143 532 18 66-89 Bracket Swaybar Chassis 144 532 17 55-82 Bracket Pnt Footrest STLT 145 532 15 65-24 Rod Pivot Chassis/Hood 159 532 18 13-55 Cupholder 206 532 17 01-65 Bolt Shoulder 5/16-18 TT 207 817 67 05-08 Screw Thdrol 5/16-18 x 1/2 TYTT 208 817 67 06-08 Screw Thdrol 3/8-16 x 1/2 TYT Bl 209 817 00 06-12 Screw 3/8-16 x 3/4 258 532 18 97-55 Lens RH 259 532 18 97-54 Lens LH 261 532 18 97-53 Insert Grille 263 532 18 38-33 Bezel RH 264 532 18 38-32 Bezel LH 278 532 19 16-11 Screw 10 x 3/4 Single Lead-Hex - - - 532 18 78-01 Plug Dome Plastic - - - 532 00 54-79 Plug NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 31 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 DRIVE 120 57 89 63 212 70 69 197 161 169 159 158 66 59 65 162 61 198 112 150 168 163 48 38 10 32 50 41 14 21 202 64 56 83 81 116 82 165 156 39 8 151 51 27 166 35 49 47 30 62 120 36 52 34 52 16 36 35 37 32 95 53 28 30 26 26 16 29 16 84 27 22 77 26 25 15 19 24 55 199 200 263 77 26 1 263 71 96 78 74 76 75 32 73 16 drive-hydro.stlt_61 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 DRIVE KEY NO. PART NO. 1 -------- 8 10 14 15 16 19 21 22 24 25 26 27 28 29 30 32 34 35 36 37 38 39 41 47 48 49 50 51 52 53 55 56 57 59 61 62 63 64 532 16 58-66 876 02 04-16 810 04 04-00 874 49 05-44 873 80 05-00 873 80 06-00 532 14 08-45 532 16 94-98 873 35 06-00 532 10 68-88 819 13 13-16 876 02 04-12 532 17 57-65 532 07 16-73 532 16 95-92 874 76 05-12 532 17 55-78 532 12 01-83 819 21 16-16 532 12 49-63 532 17 91-14 872 11 06-22 532 17 55-56 532 12 77-83 532 15 44-07 532 12 32-05 872 11 06-12 873 68 06-00 873 68 05-00 532 10 57-10 532 10 57-09 817 06 06-20 532 14 02-94 532 16 96-91 817 12 06-14 532 12 48-72 532 17 54-10 532 17 39-37 DESCRIPTION Transaxle Hydro Gr 314-0510 (Order parts from transaxle manufacturer) Rod Shift Fender STLT Pin Cotter 1/8 x 1 CAD Washer Lock Hvy Helical 1/4 Bolt Hex Flg Hd 5/16-18 x Gr. 5 Nut Lock Hex W/Ins. 5/16-18 unc P Nut Lock Hex W/Wsh 3/8-16 unc Knob Rod, Brake Hydro Nut Spring, Brake Rod Washer Pin Cotter 1/8 x 3/4 CAD. Rod, Parking Brake Cap, Parking Brake Bracket, Transaxle Bolt Hex Hd 5/16-18 unc x 3/4 Shaft, Foot Pedal Bearing, Nylon Washer Pin, Roll Pulley, Idler, Composite Bolt Fin Hex 3/8-16 unc x 2-3/4 Keeper, Belt Idler Pulley, Idler, V-Groove Bellcrank Clutch Grnd Drv Stl Retainer, Belt Bolt Carr. 3/8-16 x 1-1/2 Gr. 5 Nut Crownlock 3/8-16 Nut Crownlock 5/16-18 Link, Clutch Spring, Return, Clutch Screw 3/8-16 x 1-1/4 SMGML Tap/R V-Belt, Ground Drive Keeper, Center Span Screw 3/8-16 x .875 Cover, Pedal Pulley, Eng Bolt Hex 7/16-20 x 4 Ga. 5 KEY NO. PART NO. 65 66 69 70 71 73 74 75 76 77 78 81 82 83 84 89 95 96 112 116 120 150 151 156 158 159 161 162 163 165 166 168 169 197 198 199 200 202 212 263 810 04 07-00 532 15 47-78 532 14 24-32 532 13 46-83 532 16 91-83 532 16 91-82 532 13 70-57 532 12 17-49 812 00 00-01 532 12 35-83 532 12 17-48 532 16 55-96 532 16 57-11 819 17 12-16 532 16 95-94 532 19 18-82 532 17 02-01 532 12 47-88 819 09 12-10 872 14 06-08 873 90 06-00 532 17 54-56 819 13 32-10 532 16 60-02 532 16 55-89 532 18 39-00 872 14 04-06 873 68 04-00 874 78 04-16 532 16 56-23 817 49 05-10 532 16 54-92 532 16 55-80 532 16 96-13 532 16 95-93 532 16 96-12 872 14 05-08 872 11 06-14 532 14 52-12 817 00 06-12 DESCRIPTION Washer Keeper Belt Engine Screw Hex wsh Hi-Lo 1/4-1/2 unc Guide Belt Mower Drive RH Strap Torque Lh Hydro Strap Torque Rh Hydro Spacer, Axle Washer 25/32 x 1-1/4 x 16 Ga. E-Ring Key, Square Washer 25/32 x 1-5/8 x 16 Ga. Shaft Asm. Cross Hydro Spring Torsion T/A Washer 17/32 x 3/4 x 16 Ga. Link Transaxle Console, Shift Control Asm Bypass Hydro Retainer Spring 1" Zinc/Cad Washer 9/32 x 3/4 x 10 Ga. Bolt 3/8-16 unc x 1 Nut Lock 3/8-16 unc Spacer Retainer Washer 13/32 x 2 x 10 Ga. Washer Srrtd 5/16 ID x 1.0 x .125 Tk Bracket Shift Mount Hub Shift Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr. 5 Nut Crownlock 1/4-20 unc Bolt Hex Fin 1/4-20 unc x 1 Gr. 5 Bracket Pivot Lever Screw 5/16-18 x 5/8 TT Yellow Bolt Shoulder 5/16-18 x .561 TT Plate Fastening Cross Shf. STLT/CRD Nyliner Snap-In 5/8" ID Washer Nyl 7/8 ID x .105 HYD CRD Bolt Shoulder 5/16-18 unc Bolt Rdhd Sqnk 5/16-18 unc x 1 Bolt 3/8-16 x 1-3/4 Gr. 5 Nut Hexflange Lock Screw 3/8-16 x .75 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 33 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 STEERING ASSEMBLY 38 12 39 1 41 42 37 37 36 44 51 54 88 91 43 71 46 8 6 29 67 67 68 67 13 65 17 46 2 8 6 87 5 87 3 32 5 11 68 26 29 82 4 43 40 43 15 28 29 15 15 10 steering_pl.lt_47 34 30 95 8 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 STEERING ASSEMBLY KEY NO. PART NO. DESCRIPTION 1 532 18 59-58 Wheel Steering 2 532 18 47-06 Axle 3 532 16 98-40 Spindle Asm LH 4 532 16 98-39 Spindle Asm RH 5 532 12 49-31 Bearing Race Thrust Harden 6 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga. 8 812 00 00-29 Ring Klip #t5304-75 10 532 17 51-21 Link Drag 11 810 04 06-00 Washer Lock Hvy Hlcl Spr 3/8 12 873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf 13 532 13 65-18 Spacer Brg Axle Front 15 532 14 52-12 Nut Hex Flange Lock 17 532 18 06-41 Shaft Asm Strg 26 532 12 68-47 Bushing Link Drag 28 819 13 14-16 Washer 13/32 x 7/8 x 16 Ga. 29 817 00 06-12 Screw 3/8-16 x 3/4 30 876 02 04-12 Pin Cotter 1/8 x 3/4 32 532 13 04-65 Rod Tie 35 873 54 05-00 Nut Crown Lock 5/16-24 unf 36 532 15 50-99 Bushing Strg 37 532 15 29-27 Screw 38 532 17 20-93 Insert Cap Strg Wh 39 819 18 24-11 Washer 9/16 ID x 1-1/2 OD x 11 Ga. 40 873 54 06-00 Nut Crownlock 3/8-24 41 532 15 99-45 Adaptor Wheel Strg 42 532 16 96-33 Boot Steering Shaft 43 532 12 17-49 Washer 25/32 x 1 1/4 x 16 Ga. 44 532 18 06-40 Extension Steering Shaft 46 532 12 12-32 Cap Spindle Fr Top Blk 51 873 54 04-00 Nut Crownlock 1/4-28 54 871 13 04-20 Bolt Hex 1/4-28 unf x 1-1/4 Gr. 8 65 532 16 03-67 Spacer Brace Axle 67 872 11 06-18 Bolt Rdhd Sq 3/8-16 x 2-1/4 68 532 16 98-27 Axle, Brace 71 532 17 51-46 Steering Asm 82 532 16 98-35 Bracket Susp Chassis Front 87 532 17 39-66 Washer Flat .781 x 1-1/2 x .14 88 532 17 51-18 Bolt Shoulder 7/16-20 91 532 17 55-53 Clip Steering 95 532 18 89-67 Washer Hardened NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm. 35 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 ENGINE 3 2 72 1 62 81 13 4 78 38 32 14 44 78 46 33 37 31 33 45 29 23 OPTIONAL EQUIPMENT Spark Arrester KEY NO. PART NO. 1 2 3 532 17 05-51 Control Throttle/Choke 817 72 04-08 Screw Hex Thd Cut 1/4-20 x 1/2 -------Engine Briggs Model No. 31G777 (Order Parts From Engine Manufacturer) 532 13 73-52 Muffler 532 16 52-91 Gasket 532 14 84-56 Tube Drain Oil Easy 532 16 98-37 Shield Browning/Debris Guard 532 19 18-12 Control Choke 532 13 71-80 Kit Spark Arrestor (Flat Scrn) 532 14 05-27 Cap Asm Fuel 532 12 34-87 Clamp Hose Black 4 13 14 23 25 29 32 33 engine-bs.1cyl_48 DESCRIPTION KEY NO. PART NO. DESCRIPTION 37 38 44 45 46 62 72 78 81 532 13 70-40 532 18 16-54 817 67 04-12 817 00 06-12 819 09 14-16 810 01 05-00 817 07 05-12 817 06 06-20 873 51 04-00 Line Fuel Plug Drain Oil Easy Screw Hexwsh Thdrol 1/4-20 x 3/4 Screw Hex Wsh Thdr 3/8-16 x 3/4 Washer 9/32 x 7/8 x 16 Ga. Washer Split Screw Hex Head Cap 5/16 Screw 3/8-16 x 1-1/4 Nut Keps Hex 1/4-20 Starter Nut NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 36 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 SEAT ASSEMBLY 1 8 8 9 14 9 7 7 10 5 6 22 21 2 24 5 16 15 11 4 13 17 3 12 seat_lt.knob_9 KEY NO. PART NO. 1 2 3 4 5 6 7 8 532 18 87-05 532 18 01-66 871 11 06-16 819 13 16-10 532 14 50-06 873 80 06-00 532 12 41-81 817 00 06-16 9 10 11 12 819 13 16-14 532 18 01-86 532 16 63-69 532 12 12-46 DESCRIPTION Seat Bracket Pivot Seat Bolt Fin Hex 3/8-16 unc x 1 Washer 13/32 x 1 x 10 Ga. Clip Push-In Nut Hex w/Ins. 3/8-16 unc Spring Seat Cprsn 2 250 Blk Zi Screw 3/8-16 x 1-1/2 Smgml Tap/RZ Washer 13/32 x 1 x 14 Ga. Pan Seat Knob Seat Adj. Wingnut Bracket Mounting Switch KEY NO. PART NO. 13 14 15 16 17 21 532 12 12-48 872 05 04-12 532 13 43-00 532 12 12-50 532 12 39-76 532 17 18-52 22 24 DESCRIPTION Bushing Snap Blk Nyl 50 Id Bolt Rdhd Sqnk 1/4-2 x 1-1/2 Spacer Split 28 x 96 Yel Zinc Spring Cprsn 1 27 Blk Pnt Nut Lock 1/4 Lge Flg Gr. 5 Zinc Bolt Shoulder 5/16-18 unc-2a Blk DA 873 80 05-00 Nut Hex Lock W/Ins 5/16-18 819 17 19-12 Washer 17/32 x 13/16 x 12 Ga. NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm 37 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 DECALS 12 3 3 20 9 6 7 15 1 4 11 2 14 KEY NO. 1 2 3 4 5 6 7 9 11 PART NO. 532 16 88-69 532 17 35-89 532 19 32-03 532 17 35-87 532 15 70-02 532 19 40-81 532 15 68-11 532 19 32-09 532 19 32-10 DESCRIPTION KEY NO. Decal Tick Mark Decal LH Reflector Decal Hood Decal RH Reflector Decal Fender Danger Decal Side Panel Decal Fender Operator Decal Fender Decal Engine 12 14 15 20 ------ 532 18 57-33 532 16 03-96 532 17 91-28 532 14 50-05 532 16 69-60 532 18 82-52 532 18 82-53 532 13 83-11 532 19 31-94 Decal Wheel Steering Decal V-Belt Schematic Decal Deck "B" 42" Decal Bat Dan/Psn Decal By-Pass Pad Footrest LH STLT Pad Footrest RH STLT Decal Handle Lft Height Adjust Manual Owner's English KEY NO. 1 2 3 4 5 6 7 8 9 10 11 -- PART NO. 532 05 91-92 532 06 51-39 532 10 62-22 532 05 99-04 532 12 51-21 532 12 49-57 532 12 49-59 532 12 51-22 532 13 84-68 532 12 49-26 532 19 32-68 532 14 43-34 DESCRIPTION Cap Valve Tire Stem Valve Tire F Ts 15 x 6.0 - 6 Service Tube Front (Service Item Only) Rim Asm 6" front Service Fitting Grease (Front Wheel Only) Bearing Flange (Front Wheel Only) Rim Asm 8" rear Service Tire R Ts 20 x 8-8 C Service Tube Rear (Service Item Only) Cap Axle Sealant, Tire (10 oz. Tube) WHEELS & TIRES 1 2 5,8 7 4,10 3,9 6 11 PART NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm wheel_1 38 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 MOWER LIFT 7 8 5 1 3 13 4 2 6 6 11 5 4 12 13 19 20 31 32 13 15 19 KEY NO. PART NO. DESCRIPTION 1 2 3 4 5 6 7 8 11 12 13 532 15 94-61 532 15 94-76 532 18 88-22 812 00 00-02 819 21 16-21 532 12 01-83 532 12 56-31 532 12 45-26 532 13 98-65 532 13 98-66 532 12 46-70 Wire Asm Inner W/plunger Shaft Asm Lift Pin Groove E Ring #5133-62 Washer 21/32 x 1 x 21 Ga. Bearing Nylon Blk 629 Id Grip Handle Button Plunger Link Lift LH Link Lift RH Retainer Spring 20 20 31 32 17 18 16 20 15 lift-rh.1piece_3 KEY NO. PART NO. DESCRIPTION 15 16 17 18 19 20 31 32 532 17 32-88 873 35 08-00 532 17 56-89 873 80 08-00 532 13 98-68 532 16 35-52 532 16 98-65 873 54 06-00 Link Front Nut Jam Hex 1/2-13 unc Trunnion Blk Zinc Nut Lock W/wsh 1/2-13 unc Arm Suspension Rear Retainer Spring Bearing pvt. Lift Nut Crownlock 3/8-24 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 39 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 MOWER DECK 67 158 68 185 36 40 od _7 152 40 42 _c lu tc h_ m 143 45 150 144 159 46 40 145 184 44 54 48 147 148 59 56 53 52 55 142 146 33 32 31 106 30 104 103 21 101 42_ 119 21 104 106 23 24 25 2 26 16 15 118 20 131 129 3 4 5 te 21 113 111 21 130 92 la h_p 2 34 147 2 117 mulc 102 142 116 105 105 21 1 103 102 92 18 14 18 149 13 112 118 19 21 11 119 10 9 113 8 42_D_man-t-path_stlt_3 40 27 29 21 2 6 28 117 116 TRACTOR - - MODEL NO. MC175H42ST (MC175H42STA), PRODUCT NO. 964 77 30-00 MOWER DECK KEY NO. PART NO. DESCRIPTION 1 2 3 4 5 6 8 9 10 11 13 14 15 16 18 19 20 21 23 24 25 26 27 28 29 30 31 32 33 34 36 40 44 45 46 48 52 53 54 55 56 59 67 532 16 58-92 872 14 05-06 532 13 80-17 532 16 54-60 532 12 46-70 532 17 80-24 532 85 08-57 810 03 06-00 532 14 02-96 532 13 41-49 532 13 76-45 532 12 87-74 532 11 04-85 532 17 44-93 872 14 05-05 532 13 28-27 532 15 97-70 873 68 05-00 532 17 75-63 532 10 53-04 532 12 37-13 532 11 04-52 532 17 18-59 819 11 10-16 532 13 14-91 532 17 39-84 532 18 76-90 532 17 34-36 532 17 83-42 872 11 06-12 532 17 34-38 873 90 06-00 532 14 00-88 532 12 47-88 532 13 77-29 532 13 39-44 532 13 98-88 532 18 49-07 532 17 85-15 532 15 50-46 532 12 20-52 532 17 34-42 532 17 15-98 Deck Asm MWR 42"weldment Bolt Rdhd Sqnk 5/16-18 unc x 3/4 Bracket Asm Fr Sway Bar 38/42 Bracket Asm Deck 42"sway Bar Retainer Spring Bar Sway Deck Bolt 3/8 - 24 x 1.25 Gr. 8 Washer Lock Hvy 3/8 Washer Hard Blade Mower Vented Blade Mower 42" Shaft Asm W/lower Bearing Housing Mandrel Vented Bearing Ball Mandrel Stripper Mower Vented Bolt Rdhd Sqnk 5/16-18 x 5/8 Bolt Shoulder Baffle Vortex 42 Nut Crownlock 5/16-18 unc Bracket Deflector Mower 42" Cap Sleeve 80x 112 Blk Mower Spring Torsion Deflector 2 52 Nut Push Phos & Oil Shield Deflector Mower 42" Blk Washer 11/32 x 5/8 x 16 Ga. Rod Hinge 42"6 75 Wlg Screw Thd Rolling Washer Head Washer Spacer Pulley Mandrel Nut 9/16 Toplock Flng Oil Dip Bolt Rdhd 3/8-16 unc x 1-1/2 Gr. 5 Pulley Idler Flat Nut Lock Flg 3/8-16 unc Guard Mandrel LH Black Spring Retainer 1" Zinc/cad Screw Hex Thd Cut 1/4-20 x 5/8 T Washer Hardened Smaller Bolt Shoulder 5/16-18 unc Blkz Arm Asm Pad Brake Washer Hardened Arm Idler 42"mower LT/YT Spacer Retainer Mower Guard TUV Idler Knob KEY NO. PART NO. 68 92 101 102 103 104 105 106 111 112 113 116 117 118 119 129 130 131 142 143 144 145 146 147 148 149 150 151 152 158 159 184 185 -- 532 14 49-59 873 80 06-00 532 13 64-20 871 08 10-10 819 06 12-16 810 07 10-00 532 16 07-93 532 12 50-04 532 18 30-74 532 18 30-75 817 00 05-10 532 12 48-42 532 18 86-06 873 93 06-00 819 12 14-14 819 13 13-12 874 78 06-16 872 14 06-08 532 16 58-90 532 15 71-09 532 17 34-41 532 17 34-37 532 17 34-43 532 13 13-35 532 16 90-22 532 16 58-98 819 09 12-10 532 16 96-70 532 16 96-76 817 72 04-08 872 14 06-14 819 13 14-10 532 18 82-34 532 13 07-94 -- DESCRIPTION V-Belt Mower 42" Nut Lock Hex W/Ins 3/8-16 unc Cover Mulching Screw 10-24 x 5/8 Washer #10 Washer Lock #10 Latch Asm. Nut Weld Bracket Wheel Gauge LH 42" Deck Bracket Gauge Wheel RH 42" Deck Screw 5/16-18 Bolt Shoulder Wheel Gauge Nut Centerlock 3/8-16 unc Washer 3/8 x 7/8 x 14 Ga. Washer 13/32 x 13/16 x 12 Ga. Bolt Fin Hex 3/8-16 unc x 1 Gr. 5 Bolt Rdhd Sqnk 3/8-16 x 1 Arm Spring Brake Mower Bracket Arm Idler 42" Keeper Belt 42" Clutch Idler Pulley Idler Flat Bolt Carriage Idler Spring Extension Spring Return Idler Retainer Spring Yellow Washer 9/32 x 3/4 x 10 Ga. Bracket Clutch Cable Clutch Cable 42" Screw Hex Thd Cut 1/4-20 x 1/2 Bolt Rdhd Sqn 3/8-16 unc x 1-3/4 Washer 13/32 x 7/8 x 10 Ga. Head Asm. Cable Clutch Mandrel Asm Service (Includes Housing, Shaft and Shaft Hardware Only-Pulley Not Included) 532 16 95-83 Replacement Mower, Complete (Std. Deck - Order separately mulch cover and gauge wheel components key nos. 101-106 and 116-119) NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 41 SERVICE NOTES 42 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL D AL ONG THIS DOT IS A TED 15 D LINE EGR EE S LO P E 43 ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project