Automation Variable Speed Drives

Automation Variable Speed Drives
Motors | Energy | Automation | Coatings
Automation
Variable Speed Drives
www.weg.net
VSD
VSDs are intended for speed control of
three-phase induction motors in a wide variety
of industrial applications. The WEG VSD
series offer state-of-the-art technology in
motor control with a modern design, great
number of features, and easily installed and
operated.
These products are designed with highsoftware optimization and are easily set
through a simple Human-Machine Interface.
Additionally, they comprise functions and
resources that allow protection and control of
electric motors extremely easily and efficiently.
They are suitable to operate with scalor or
vector control.
2
Variable Speed Drives
www.weg.net
CFW-08
The WEG CFW-08 VSDs are intended for speed control of three-phase induction motors. These VSDs incorporate the
most advanced technology features in a compact product, besides a set of special functions that are available.
WEG CFW-08 VSDs are easy to install and operate. They are equipped with an optimized software that can be easily
set through a keypad, which enables them to process and control most of industrial machines. In addition, the CFW-08
Plus is equipped with dead time compensation technique, thus avoiding motor instability and providing increase of
torque at low speeds.
Standard Features
Main Applications
DSP (Digital Signal Processor) control provides a reasonable
improvement of inverter performance
g State-of-the-Art Technology with the newest generation of
IGBTs
g Electronics with SMD components
g Scalor (V/F) or sensorless vector control
g Sinusoidal PWM modulation- Space Vector Modulation
g Latest generation IGBT modules
g Considerable motor noise reduction
g Interface with membrane keypad (standard and remote HMI)
g Flexible programming
g Compact dimensions
g Easy installation and operation
g High starting torque
g Conduit installation kit
g Optional internal (class A) and external (class B) EMC filters
g
Centrifugal pumps
Process pumps
g Fans / Exhausters
g Stirrers / Mixers
g Extruding machines
g Conveyors
g Roller tables
g Granulators / Peletizers
g Driers / Rotating ovens
g Rotating filters
g Winding / Unwinding machines
g Cutting and welding machines
g
g
Certifications
Block Diagram
CFW-08
Vdc
Vdc
Vdc
(1) Only avaliable to control board A2
(2) Only avaliable to control board A3
(3) Only avaliable to control board A4
(4) Not avaliable for 500-600V
Variable Speed Drives
3
www.weg.net
CFW-08 - Specification Table
Power
Supply
Voltage
Power
Supply
200/220/230/240V
Single-Phase
Single-Phase or
Three-Phase
Three-Phase
380/400/415/440/480V
Three-Phase
500-600V
500-600V
Three-Phase
Three-Phase
Three-Phase
CFW-08 DRIVES
Maximum Applicable Motor
Part Number
CFW-08
Dynamic
Braking
Current
(A)
Size
CFW080016S2024ESZ
No
1.6
CFW080026S2024ESZ
No
2.6
CFW080040S2024ESZ
No
CFW080016B2024ESZ
CFW080026B2024ESZ
Voltage
(V)
HP
kW
1
0.25
0.25
1
0.5
0.37
4
1
1
0.75
No
1.6
1
0.33
0.25
No
2.6
1
0.5
0.37
CFW080040B2024ESZ
No
4
1
1
0.75
CFW080073B2024ESZ
Yes
7.3
2
2
1.5
CFW080100B2024ESZ
Yes
10
2
3
2.2
230
Dimensions (mm)
Power rating
Weight
(Kg)
H
W
D
151
75
131
1
151
75
131
1
200
115
150
2
1
CFW080070T2024ESZ
No
7
1
2
1.5
151
75
131
CFW080160T2024ESZ
Yes
16
2
5
4
200
115
150
2
CFW080220T2024ESZ
Yes
22
3
7.5
5.5
203
143
165
2.5
CFW080280T2024ESZ
Yes
28
4
10
7.5
CFW080330T2024ESZ
Yes
33
4
12.5
9.5
290
182
196
6
151
75
131
1
200
115
150
2
203
143
165
2.5
290
182
196
6
151
75
131
1
200
115
150
2
203
143
165
2.5
290
182
196
6
203
143
165
2.5
203
143
165
2.5
CFW080010T2024ESZ
No
1
1
0.25
0.25
CFW080016T2024ESZ
No
1.6
1
0.5
0.55
CFW080026T2024ESZ
No
2.6
1
1
0.75
CFW080040T2024ESZ
No
4
1
2
1.5
CFW080027T2024ESZ
Yes
2.7
2
1.5
1.1
CFW080043T2024ESZ
Yes
4.3
2
2
1.5
CFW080065T2024ESZ
Yes
6.5
2
3
3
CFW080100T2024ESZ
Yes
10
2
6
4
CFW080130T2024ESZ
Yes
13
3
7.5
5.5
CFW080160T2024ESZ
Yes
16
3
10
7.5
CFW080240T2024ESZ
Yes
24
4
15
11
CFW080300T2024ESZ
Yes
30
4
20
15
CFW080010T2024ESZ
No
1
1
0.33
0.25
CFW080016T2024ESZ
No
1.6
1
0.75
0.55
CFW080026T2024ESZ
No
2.6
1
1.5
1.1
400/415
CFW080040T2024ESZ
No
4
1
2
1.5
CFW080027T2024ESZ
Yes
2.7
2
1.5
1.1
CFW080043T2024ESZ
Yes
4.3
2
2
1.5
CFW080065T2024ESZ
Yes
6.5
2
4
3
CFW080100T2024ESZ
Yes
10
2
6
4.5
CFW080130T2024ESZ
Yes
13
3
7.5
5.5
CFW080160T2024ESZ
Yes
16
3
10
7.5
CFW080240T2024ESZ
Yes
24
4
15
11.3
CFW080300T2024ESZ
Yes
30
4
20
15
CFW080017T5060ESZ
Yes
1.7
1
0.75
CFW080030T5060ESZ
Yes
3.0
2
1.5
CFW080043T5060ESZ
Yes
4.3
3
2.2
CFW080070T5060ESZ
Yes
7.0
5
4
3
440
525
CFW080100T5060ESZ
Yes
10
7.5
5.5
CFW080120T5060ESZ
Yes
12
10
7.5
CFW080017T5060ESZ
Yes
1.7
1
0.75
CFW080030T5060ESZ
Yes
3.0
2
1.5
CFW080043T5060ESZ
Yes
4.3
3
2.2
CFW080070T5060ESZ
Yes
7.0
5
3.7
CFW080100T5060ESZ
Yes
10
7.5
5.5
CFW080120T5060ESZ
Yes
12
10
7.5
3
575
NOTE: The maximum motor power ratings listed above were based on WEG II and IV-pole motors. For motors with different number of poles (ex.: VI and VIII poles),
other voltages (ex.: 220V, 380V and 460V) and/or motors from other manufacturers, specify the VSD according to the rated motor current.
4
Variable Speed Drives
www.weg.net
CFW-08 - Models and optional accessories
Standard
Blank Keypad
Standard Model
with HMICFW08-P
(Human
Machine
Interface)
Serial Interface Module RS-485
Optional Model
without HMI (with
dummy cover/blank
keypad)
Serial Interface Module RS-232
HMI Remote Interface Module
Optional Kit:
Serial
communication
RS-485 (KRS485-CFW08)
Parallel HMI Remote Interface Module
Optional Kit:
Parallel, remote
HMI interface
(MIP-CFW08-RP)
Connection in Metallic Conduit
Optional Kit:
Connection in
Metallic Conduit
(NEMA 1/IP21)
KN1-CFW08-MX
available for sizes
1 and 2
Optional Kit: Serial
communication RS232 (KCS-CFW08)
Optional Kit:
Serial, remote
HMI interface
(MIS-CFW08-RS)
DIN Rail Mounting Base
Optional Kit: Din
rail mounting
base(KMDCFW08-M1) (only
for Size 1)
Interface module KAC – 120
Optional Kit:
Driving at 120 Vac
of the digital inputs
(KAC – 120 –
CFW08)
Variable Speed Drives
5
www.weg.net
CFW-08 - Remote Keypad
HMI remote serial
HMI remote on parallel
g
It allows starting on panel door with maximum distance of
10m.
It allows starting on panel door with maximum distance of
150m (Distance above 10m requires external source
12V / 250 mA).
g Copy function available
g
VSD with interface
MIP-CFW-08-RS
VSD with interface
MIS-CFW-08-RS
HMI-CFW08-RS
Serial Remote Keypad
CAB-RP-X
HMI-CFW08-RP
Parallel Remote Keypad
CAB-RS-X
Superdrive
WEG Superdrive is a windows based software program that
follows serial (RS 232 or RS 485) communication between a PC
and all WEG Soft Starters and Variable Speed Drives (VSD).
Superdrive is an excellent programming, documentation, and
troubleshooting tool for WEG Starters and VSDs.
Superdrive is available for free download at
www.weg.net. Hardware accessories may be required
depending on the Soft Starter or VSD line.
Model with
SUPERDRIVE Kit
KSD-CFW08
6
Variable Speed Drives
www.weg.net
CFW-08 - Fast network interconnection
CFW-08 Speed drives can be interconnected in “FieldBus”
fast communication networks through the most wide
spread, standard protocols. They can be:
FIELDBUS
Profibus DP (optional)
DeviceNet (built-in protocol) (1)
ModbusRTU
(built-in protocol)
CANopen (built-in protocol) (1)
Intended mainly for the integration of large, industrial
automation plants, the fast communication networks
provide advantages in the supervision, monitoring and
control of the drives. This provides high working
performance and great operational flexibility, which are
required characteristics in complex systems and / or
integrated applications.
For the interconnection of the CFW-08 variable speed
drives, the following options and characteristics can
be used:
Profibus DP: Communication uses a serial interface
RS-232 (KRS-232-CFW08) or RS-485 (KRS-485CFW08) switched to an MFW01 gateway for the
Profibus DP.
g
DeviceNet: Software available through the A4
control card and Device-Net interface (KFB-DNCFW08) (1)
g
CANopen: Software available through the A3 control
card and CANopen interface (KFB-CO-CFW08) (1)
g
Modbus - RTU: Software available through the A1
and A2 standard control cards and serial interface
RS-232 (KCS-CFW08) or RS-485 (KRS-485CFW08)
g
(1)
NETWORKS
FIELDBUS
Not avaliable for 500-600V
CANopen
DeviceNet
Modbus RTU
(RS-485)
Modbus RTU
(RS-232)
Profibus DP
Variable Speed Drives
7
www.weg.net
CFW-08 - Multipump Drive
VSDs allow a system to maintain the line pressure in pipes completely constant, independently from fluctuations in outflow demand.
The Multipump Drive controls up to 4 pumps simultaneously. Another interesting function of the multipump drive is the intelligent
start of the auxiliary pumps for their operation time is considered.
Besides controlling the pumps output pressure, the drive also monitors the suction pressure and the level of the capture reservoir.
Advantages of the multipump control
Energy Savings;
Longer lifetimes for the pumps;
g Maintains the line pressure constant;
g Provides the necessary outflow according to the demand
of the system;
g Soft starts, protecting the mechanical and electrical installation;
g Alternation in running auxiliary pumps based on operating hours.
g
g
CFW-08 - Wash
Power Supply
Single-Phase or
Three Phase
500/600V
500/600V
380/400/415/480V
380/400/415/480V
Power
Supply
Voltage
200
220/230
240V
Coming from the robust performance of the original CFW-08, the NEMA 4X AC Drive features a IP56-rated enclosure that protects
against high-pressure water, corrosion and circulating dust.
The drive is designed to be mounted directly in severe environments and can be used in wash-down applications without the need
for a custom enclosure.
8
Three-Phase
Three-Phase
Three-Phase
Three-Phase
CFW-08 DRIVES NEMA 4X
Dynamic
Model
Current (A) Size
Braking
CFW080073B2024PON4A1Z
YES
7.3
A
Maximum Applicable Motor
Power Rating
Voltage (V)
HP
kW
2
1.5
230
3
2.2
Dimensions (mm)
Weight( kg)
Height
265
Width
165
Depth
216
5
265
165
216
5
CFW080100B2024PON4A1Z
YES
10
A
CFW080027T3848PON4A1Z
YES
2.7
A
1.5
1.1
265
165
216
5
CFW080043T3848PON4A1Z
YES
4.3
A
2
1.5
265
165
216
5
CFW080065T3848PON4A1Z
YES
6.5
A
3
3
265
165
216
5
CFW080100T3848PON4A1Z
YES
10
A
6
4
265
165
216
5
CFW080130T3848PON4A1Z
YES
13
B
7.5
5.5
340
215
216
8
CFW080160T3848PON4A1Z
YES
16
B
10
7.5
340
215
216
8
CFW080240T3848PON4A1Z
YES
24
B
15
11
340
215
216
8
CFW080300T3848PON4A1Z
YES
30
B
20
15
340
215
216
8
CFW080027T3848PON4A1Z
YES
2.7
A
1.5
1.1
265
165
216
5
CFW080043T3848PON4A1Z
YES
4.3
A
3
2.2
265
165
216
5
CFW080065T3848PON4A1Z
YES
6.5
A
4
3
265
165
216
5
CFW080100T3848PON4A1Z
YES
10
A
7.5
5.5
265
165
216
5
CFW080130T3848PON4A1Z
YES
13
B
10
7.5
340
215
216
8
CFW080160T3848PON4A1Z
YES
16
B
10
7.5
340
215
216
8
CFW080240T3848PON4A1Z
YES
24
B
15
11
340
215
216
8
CFW080300T3848PON4A1Z
YES
30
B
20
15
340
215
216
8
CFW080017T5060PON4A1Z
YES
1.7
B
1
0.75
340
215
216
8
CFW080030T5060PON4A1Z
YES
3.0
B
2
1.5
340
215
216
8
CFW080043T5060PON4A1Z
YES
4.3
B
3
2.2
340
215
216
8
CFW080070T5060PON4A1Z
YES
7.0
B
5
4
340
215
216
8
CFW080100T5060PON4A1Z
YES
10
B
7.5
5.5
340
215
216
8
CFW080120T5060PON4A1Z
YES
12
B
10
7.5
340
215
216
8
CFW080017T5060PON4A1Z
YES
1.7
B
1
0.75
340
215
216
8
CFW080030T5060PON4A1Z
YES
3.0
B
2
1.5
340
215
216
8
CFW080043T5060PON4A1Z
YES
4.3
B
3
2.2
340
215
216
8
CFW080070T5060PON4A1Z
YES
7.0
B
5
4
340
215
216
8
CFW080100T5060PON4A1Z
YES
10
B
7.5
5.5
340
215
216
8
CFW080120T5060PON4A1Z
YES
12
B
10
7.5
340
215
216
8
Variable Speed Drives
400/415
440
525
575
www.weg.net
CFW-08 - Technical Data
Model
Voltage
POWER SUPPLY
Single-Phase
Three-Phase
Frequency
Cos * (Displacement
Power Factor)
Standard
Drive
Optional
CFW-08 Standard
CFW-08 Plus
200-240V: 200/220/230/240 V (+10% - 15%)
200-240V: 200/220/230/240 V (+10% - 15%)
380-480V: 380 / 400 / 415 / 440 / 460 / 480 / 525 / 575 V (10% - 15%)
50 / 60 Hz +/- 2 Hz ( 48...62 Hz)
> 0.98
NEMA 1 in sizes 3 and 4and IP 20 in sizes 1 and 2
NEMA 1 with optional kit for connection in metalic conduit (KN1-CFW08-MX)
ENCLOSURE
NEMA 12 Parallel, remote HMI (IP54) (HMI-CFW08-RS)
HMI
Optional
NEMA 12 Serial, remote HMI (IP54) (HMI-CFW08-RS)
Power Supply Type
Switching power supply
Control Method
DSP (Digital Signal Processor), 16 bits, sinusoidal PWM (Space Vector Modulation)
Imposed voltage - linear V/Hz or quadratic
Control Type
Sensorless vector control (WC: Voltage Vector Control)
CONTROL
Switching Frequency
IGBT Transistors - Frequencies: 2.5 / 5.0 / 10 / 15 kHz
Frequency Range
0...300Hz
Fequency Resolution
Analog Ref.: 0.1% of Fmax. And digital ref.: 0.01 Hz (f<100Hz); 0.1 Hz (f>100 Hz)
Accuracy (25º C = 10ºC)
Analog Ref.: 0.5% and digital Ref.: 0.01%
Overload capacity
150% during 60 sec. Every 10 min (1.5 x Rated Current.)
PERFOMANCE
Efficiency
>95%
Speed control
Regulation: 1% of the rated speed with slip compensation
Analog
1 isolated input 0..10 V. 0/4...20 mA or - 10...+10V (Al1)1 2 isolated inputs 0..10, 0/4...20mA or - 10...+10V (Al1 e Al2)1
4 Programmable isolated inputs - with
INPUTS
NPN or PNP logic (Dl1...Dl4)
Digital
1 Isolated PTC input via Al1
2 Isolated PTC inputs via AL1 and AL2
1 programmabie output, I reversal contact (NU/NC)
2 Programmable outpluts, I no and TNC
Relay (2)
OUTPUTS
Programming options: Is > Ix; Fs > Fx; Fe> Fx; Fs = Fe; Run
Analog (2)
1 Isolated analog output 0...10V, 0/4...20mA ( 8 bits )
Serial Interface
RS-232 or RS-485 (optional)
COMMUNICATION
“Field Bus” Networks
Unit for ProfiBus DP Communication, DeviceNet (optional) and ModBus RTU (built-in)
DC link overvoltage / undervoltage
Overtemperature
Output overcurrent
SAFETY
Protections
Motor overload ( i x t )
Hardware fault, external fault and serial communication error
Output phase to phase and phase to ground short circuit
Programming fault and self-tuning error
On/Off , Parameter Setting ( Programming of special functions )
Commands
Frequency Increment / Decrement ( Speed )
JOG, Reversal of Direction of Rotation and Local /Remote Selection
Motor Output Frequency ( Hz )
DC Link Voltage ( V )
HUMAN-MACHINE
Value proportional to the frequency ( Ex.:RPM )
INTERFACE
(HMI)
Heat Sink Temperature
Monitoring (Reading)
Motor Output Current ( A )
Motor Output Voltage ( V )
Error / Fault Messages
Load Torque
Temperature
0 ... 40 °C (up to 50 °C with output current derating 2% / °C)
ENVIRONMENT
Humidity
5 ... 90% non condensing
Altitude
0 ... 1000 m (up tp 4000 m with output current derating 10% / 1000 m)
FINISHING
Color
Politherm 20 mt gray and Politherm 20 mt blue
Electromagnetic
EMC Directive 89/336/EEC - Industrial Environment; EN 61800-3 (EMC - Emission and Immunity)
Compatibility
Low Voltage
LVD 73/23/EEC - Low Voltage Directive / UL 508C
IEC 146
Semiconductors convertors
STANDARDS
UL 508 C
Power conversion equipment
EN 50178
Electronic equipment for use in power installations
EN 61010
Safety requirements for electrical equipment for measurement, control and laboratory use
UL (USA) and cUL
Underwriters Laboratories Inc. / USA
(CANADA)
CE (EUROPE)
SGS / England
CERTIFICATIONS
IRAM (ARGENTINA)
Instituto Argentino de Normalización
C-Tick (AUSTRALIA)
Australian Communications Authority
(1) Only avaliable to control board .
(2) To control board A5 (multipump) there are 3 output by relays (contact N/A) there is not output analog.
Variable Speed Drives
9
www.weg.net
CFW-08 - Coding
CFW08 0040 B 2024 P 0
1
2
3
4
5
6
--
-- --
--
7
8
10
9
-11
-- Z
12
13
1 - CFW-08 Variable Speed Drives
2 - Output Rated Current:
200-240 V
0016
1,6 A
0026
2,6 A
0040
4,0 A
0070
7,0 A
0073
7,3 A
0100
10 A
0160
16 A
0170
17 A
0220
22 A
0280
28 A
0330
33 A
380-480 V
0010
1,0 A
0016
1,6 A
0026
2,6 A
0027
2,7 A
0040
4,0 A
0043
4,3 A
0065
6,5 A
0100
10 A
0130
13 A
0160
16 A
0240
24 A
0300
30 A
500-600 V
0017
1,7 A
0030
3,0 A
0043
4,3 A
0070
7,0 A
0100
10 A
0120
12 A
3 -Power Supply
S = single-phase
T = three-phase
B = single-phase or three-phase
4 -Power Supply Voltage
2024 = 200-240 V
3848 = 380-480 V
5060 = 500 - 600 V
5 -Manual Language
P = Portuguese
E = English
S = Spanish
G = German
6 -Options
S = Standard
O = Options
7 -Enclosure
Blank = standard
SI = without keypad
8 -Keypad/HMI
Blank = standard
SI = without interface
9 -Control Board
Blank = standard (CFW-08 Standard)
A1 = control 1 (CFW-08 PLUS)
A2 = control 2 (CFW-08 Plus with bipolar analog inputs)
A3 = CANopen (1)
A4 = DeviceNet (1)
A5 = Pumps
10 - EMI Filter
Blank = without filter
FA = Internal Class A filter 11 - Special Hardware
Blank = not provided
Hx = X version special hardware
12 - Special Software
Blank = not provided
Sx = X version special software
13 - End of Code
Ex.: CFW080040B2024EOA1Z
VSD of CFW-08 series, 4.0 A, single-phase
or three-phase at 200-240 Vac, manual in
English and control board 1 (CFW-08 Plus).
(1)
10
Variable Speed Drives
Not avaliable for 500-600V
www.weg.net
CFW-08 - Resources / Special Fuctions
Standard / Plus Features
g Incorporated Human-Machine Interface - 7 segment LED
g Programming enabling password
g Fault self-diagnosis and Auto-Reset
g Specific value indication (programmable) - (Ex.: m/min; rpm, etc)
g Slip compensation (U/F control)
g Manual and automatic torque boost
g Adjustable U/F curve
g Self-tuning (sensorless vector control)
g Dynamic braking
g JOG Function (transitory speed pulses)
g COPY Function via remote keypad (HMI-CFW08-RS)
g Linear, ’S’ type and double ramps
g Acceleration and deceleration ramps (independent)
g DC braking (DC Current)
g Multi-Speed Function (up to 8 pre-programmable speeds)
g FWD/REV Selection
g Local/Remote Operation selection
g PID Regulator (automatic level, pressure control, etc)
g Running motor start (Flying Start)
g Rejection of critical or resonant frequencies (Skip Frequency)
g Operation during transitory line loss (Ride-through)
g Units for Fieldbus Communication:
- Modbus RTU (built-in)
- DeviceNet
- CANopen
g Multipump control
Optional Features
Parallel Remote Keypad (HMI) (7 segment LED) - HMI-CFW08-RP
g Serial Remote Keypad (HMI) (7 segment LED) - HMI-CFW08-RS
g Interface Module for Serial Remote Keypad (HMI) - MIS-CFW08-RS
g Interface Module for Parallel Remote Keypad (HMI) - MIP-CFW08-RP
g Interface Module for starting with digital input in 120 Vac - KAC - 120 - CFW08
g Interconnection Cable of the Serial Remote HMI (1; 2; 3; 5; 7.5 and 10 m) - CAB-RS-X
g Interconnection Cable of the Parallel Remote HMI (1; 2; 3; 5; 7.5 and 10 m) - CAB-RP-X
g Serial Communication module RS-232 - KCS-CFW08
g Serial Communication module RS-485 - KCS-485-CFW08
g CANopen Communication module KFB-CO-CFW08
g DeviceNet Communication module KFB-DN-CFW08
g ProfiBus DP Communication module KCS-CFW08 or KRS-485-CFW08 + MFM-01/PD
g RS-232 to RS-485 Converter (MCS-CFW08 Module required) - MIW-02
g Windows based programming software - SUPERDRIVE
g NEMA 1 Kit for metallic conduit connection - KN1-CFW08-MX
g Din rail mounting kit - KMD-CFW08-M1
g EMC Filter with high Attenuation Capacity (Class A - internal)
g EMC Filter with high Attenuation Capacity (Class B - external)
g
Variable Speed Drives
11
www.weg.net
CFW-09
The WEG CFW-09 Series of Variable Speed
Drives incorporate the world’s most advanced
technology in drives for three-phase AC
induction motors.
The Vectrue Technology™ represents a
siginificant advancement, allowing this
generation of WEG VSD to combine V/F,
Sensorless Vector and Closed Loop Vector
(with encoder) control techniques, all in one
product.
An innovation was also introduced to simplify
applications that require braking torque. A new
feature named Optimal Braking™ eliminates
the need for the dynamic braking resistor in
some applications allowing a simple, more
compact and economical solution.
Vectrue Technology ®
This technology was developped by WEG for variable speed
applications with three-phase AC induction motors providing
the following advantages:
V/ F or Vector Control modes via parameter selection;
True Flux Vector Control in either open or closed loop
vector modes;
g True Open Loop Vector Control with high torque and fast dynamic response, even at very low speeds;
g Self-tuning for automatic drive set-up to match the drive to
motor and load in vector modes.
g
g 12
Variable Speed Drives
www.weg.net
CFW-09 - Optimal Braking TM
CFW-09 - Other Advantages
For applications requiring short stopping times and/or stops
under high inertial loading, the traditional braking devices call
for Dynamic Braking, in which the load kinetic energy is
regenerated to the inverter DC link and the excess of which is
dissipated in the form of heat in a braking resistor which is
interlinked to the power circuit. The CFW-09 VSD has a
built-in “Optimal Braking ®” function, for the vector mode,
enabling an optimal braking which can cater for many
applications that could previously only be solved by dynamic
braking. This technological innovation enables high dynamic
performance activation/starts to be obtained with braking
torques about 5 times the DC braking torque besides the
great advantage of eliminating the need for a braking resistor.
The graph shows the advantage of this new braking system “
Optimal Braking ®“, thereby ensuring an ideal solution for
braking applications at low cost.
High performance RISC 32 bit microprocessor;
Vector and Scale Control with selection by parameter;
g Detachable SMART keypad with dual display
(LCD and LED);
g Wide power range: 1.1.. 1,100 kW;
g Variable and Constant Torque ratings;
g Degree of Protection NEMA 1 / IP 20 standard up to 132kW, IP 20 up to 330kW and NEMA 4X / IP 56 in stainless steel enclosure up to 7.5kW;
g Compact design;
g Simplified installation and programming;
g Oriented start-up;
g Through surface mounting option;
g On/Off-line PC programming with SuperDrive software
(Optional);
g DC bus connections available;
g Fieldbus network communication: Profibus DP or DeviceNet (optional). Modbus RTU (built-in) also available;
g International certifications including UL and cUL, CE, C-Tick and IRAM.
g
g
Braking
Torque
Speed
Typical Braking Torque x Speed curve for motors driven by the CFW-09
Dynamic Braking Torque Curve
“Optimal Braking” TM Torque Curve
DC Braking Torque Curve
Variable Speed Drives
13
www.weg.net
CFW-09 - Applications
Chemical and Petrochemical
g Fans / Exhausters
g Centrifugal Pumps
g Metering / Processing Pumps
g Mixers
g Compressors
g Extruders
Mining and Cement
Fans / Exhausters
g Pumps
g Screeners
g Vibratory Feeders
g Crushers
g Dynamic Separators
g Conveyors
g Cement Ovens
g
Steel
Fans / Exhausters
g Roller Tables
g Winders / Unwinders
g Overhead Cranes / Cranes
g Presses / Lathes / Milling Cutters
g Drillers / Grinders
g Laminators
g Cutting Lines
g Ingot Molding Lines
g Pipe Forming Machines
g Wire Drawing Machines
g Pumps
g
Lumber
Veneer Lathes
g Chippers
g Plains
g Saws
g
HVAC
Processing Pumps
g Fans / Exhausters
g Air Conditioners Units
g
14
Variable Speed Drives
Pulp and Paper
g Metering Pumps
g Processing Pumps
g Fans / Exhausters
g Agitators / Mixers
g Rotating Filters
g Rotating ovens
g Scrap Conveyors
g Paper Machines
g Paper Rewinders
g Calenders
Sugar
Sugar Centrifugal pumps
g Process Pumps
g Conveyors
g Waste Dosers
g
Ceramic
Fans / Exhausters
g Driers / Ovens
g Ball Mills
g Rollout Tables
g Enameling machine
g Conveyors
g
Beverage
Metering / Processing Pumps
g Bottlers
g Mixers
g Roller Tables
g Conveyors
Waste Water
g Centrifugal Pumps
g Booster Systems
Textile
Mixers / Agitators
g Washers / Driers
g Looms
g Spinning Machines
g Carding Machines
g Warpers
g Winders
g
Food
Metering / Process Pumps
g Fans / Exhausters
g Mixers
g Driers / Ovens
g Palletizers
g Monorails
g Conveyors
g
Glass
Fans / Exhausters
g Bottlers
g Roller Tables
g Conveyors
g
g
Plastic and Rubber
Extruders
g Injection Machines
g Mixers
g Calenders / Pullers
g Winders / Unwinders
g Cutting and Welding Machines
g Granulators
g
Elevators
Load Elevators
g Commercial Elevators
g Overhead Cranes
g Hoists
g
www.weg.net
CFW-09 - A Complete, Flexible and Compact Product
NEMA 1 / IP20 Enclosure
Optional RS-232
Interface Module for
PC Communication
7 Segment
LED Display
2 Lines with 16
Characters LCD
Display
Fieldbus Communication
Network Modules for:
g Profibus DP (optional)
g DeviceNet (optional)
g DeviceNet Drive Profile
(optional)
g Modbus RTU (built-in)
6 Programmable
Isolated Digital Inputs
2 Programmable
Analog Inputs
Metallic Conduit
Connection System
Flange for Through
Surface Mounting
Detachable Keypad
with Multi-language
Double Display
(LCD + LED)
and Copy Function
High Performance
32 bit RISC
Microprocessor
Standard
SMD Control
Board for
all Models
Optional I/O
Expansion
Boards for:
g RS-485 Serial
Interface
g Additional
Inputs/Outputs
g Encoder Feedback
3 Programmable
Relay Outputs
AC Supply Input
Motor Connection Output
DC Bus Connection for:
g DC Bus Choke
g Common DC BusC
g Regenerative Rectifier
2 Programmable Analog Outputs
Dynamic Braking Resistor Connection
Variable Speed Drives
15
www.weg.net
CFW-09 - Mounting Configurations
The CFW-09 allows flexible mounting configurations. Besides
the traditional Base mounting, they allow flange mounting,
where the heat sink is mounted at the back of the mounting
plate.
As a result, the warm air generated by the power components
inside the panel is so blown out that minimizes drive
overheating, which is caused by heating sources inside the
panel.
Base mounting
Flange mounting
Outlet
Saída
do
fluxo
de ar
air flow
Saída
do
Outlet
fluxo de ar
air flow
Entrada
Inletdo
fluxo de ar
Entrada
Inletdo
fluxo de ar
air flow
air flow
POWER SUPPLY
Block Diagram
Precharge
Capacitor
Bank
Three-phase
Rectifier
Sensors
-Ground Fault
-Phase Fault 

Remote
Keypad
RS-232
(optional)
Internal electronics power supplies
and control/power interfaces
A
“CC9”
Control Board
with 32 bits
RISC CPU
Analog
Inputs
(A11...A12)
16
PC
PLC
DCS
FIELDBUS (Optional)
- Profibus DP
- DeviceNet
(only from Size 2 and up)
(Up to Size 7 only. Option for Sizes 4 to 7)
Variable Speed Drives
EBA/EBB/EBC/EBE
Expansion (optional)
-Isolated RS-485
-1digital input
Keypad
Digital
Inputs
(D11...DI06)
e
= DC Bus Connection
e
= DB Resistor Connection
Feedback
-Voltage
-Current
POWER
CONTROL
SuperDrive
Software
PE
DC Bus
=phase fault only from size 3
PC
e = DC Bus Choke connection (Optional)
IGBT
Inverter
RFI Filter
†
= Drive Profile Keypad
1x14 bit analog input
2x14 bit analog outputs
1x4...20mA isol. input
B 2x4...20mA isol. outputs
External
Control
- 2 digital outputs
- 1 encoder input/output
- 1 PTC input
Analog
Outputs
(AO1...AO2)
Relay
Outputs
(RL1...RL3)
www.weg.net
CFW-09 - Keypad
Intelligent Keypad
Intelligent operating interface with double display, LED (7
segment) and LCD (2 lines with 16 characters), providing
optimum distant viewing along with a detailed description of
all parameters and messages.
LED Display
Selectable Language
The intelligent operating interface also allows the product
user to choose the language to be used in programming,
reading and presenting the parameters and alphanumerical
messages through the LCD display.
The product’s high hardware and software capacity enables
the user to use various languages such as Portuguese,
English and Spanish so as to make it adaptable for users
throughout the world.
LCD Display
Oriented Start-up
The CFW-09 “Oriented Start-Up” feature was specially
created to facilited and expedite the start-up procedure. At
the first power-up or after a reset to factory default
parameters, and automatic programming routine guides the
operator through a sequence of steps for the introduction of
the minimum parameters necessary for a perfect adaptation
between drive and motor.
“LOCAL” LED
“REMOTE” LED
“FORWARD“ LED
“REVERSE” LED
COPY Function
This intelligent keypad also incorporates a “Copy Function”,
which allows copying parameters from one drive to others,
providing easy and reliable programming repeatability for
duplicate applications.
VSD “A”
CFW-09
Keypad
VSD “B”
Keypad
Variable Speed Drives
CFW-09
17
www.weg.net
CFW-09 - Keypad Functions
Starts the drive via a controlled acceleration ramp.
When running switches the display indication:
rpm - Volts - Status - Torque - Hz - Amps
Stops the drive via a controlled deceleration ramp.
Resets the inverter after a fault trip has occurred.
Increases the speed or parameter number/content.
Decreases the speed or parameter number/content.
Switches the display between the parameter number
and its content (position/content) for programming.
While pressed the motor is run at JOG speed.
FWD/REV key. When pressed reverses the direction of
rotation.
Selects the drive operating mode as Local or Remote.
Superdrive
Programming Software
Windows Programming software via PC microcomputer, for
parameterization, control and monitoring of CFW-09 drives.
It allows editing of “on-line” parameters, directly on the drive
or editing “off-line” parameter files, saved in the
microcomputer.
It also allows storage of parameter files of all CFW-09 drives
available on the installation.
The software also incorporates functions to transfer the set of
parameters from the microcomputer to the drive, as well as
from the drive to the microcomputer.
The communication between drive and microcomputer is
made via serial interface RS-232 (point to point) or RS-485 for
network interconnection.
Free software on the site www.weg.net
18
Variable Speed Drives
www.weg.net
CFW-09 - Technical Data
Voltage
POWER SUPPLY
Frequency
Phase Unbalance
Cos (Displacement Power Factor)
Degree of Protection
ENCLOSURE
Finishing Color
Power Supply
Microprocessor
PWM Technique
Control Modes
CONTROL
Switching Frequency
Frequency Range
Overload Capacity
Efficiency
Speed Control
PERFORMANCE
Torque Control
Analog
CONTROL INPUTS
Digital
Encorder
COMMUNICATlON
Serial
Fieldbus
SAFETY
AMBIENT
CONFORMITIES
CERTIFICATIONS
Protections
Temperature
Humidity
Altitude
EMC Directive 89 / 336 / EEC - EM
61800-3
LVD 73 / 23 / EEC
IEC 146
UL 508C
EN 50178
EN 61010
UL (USA) and cUL (CANADA)
CE (EUROPE)
IRAM (ARGENTINA)
C-Tiek (AUSTRALIA) 2250/1132383
220-230 V: 220 230 V (+10% -15%)
380 - 480 V: 380 / 400 / 415 / 440 / 460 / 480 V (+10%, - 15%)
500 - 600 V; 500 - 690 V; 660 - 690 V; 660/690 (+ 10%. -15%)
50 / 60 Hz +/- 2 Hz (48 ... 62 Hz)
Up to 3%
Greater Ihan 0.98
NEMA 1/IP 20 (sizes 1...8 and 8E), IP20 (sizes 9,10 and 10E)
NEMA 4X I IP 56 (modules up to 10HP)
Plastic Cover - Light Gray PANTONE 413 C (sizes 1 and 2)
Metallic Cover and Sides - Light Gray RAL 7032 (sizes 3 to 10)
Base - Dark Gray RAL 7022 (sizes 3 to 10)
Switched Mode Power Supply Fed from the DC Link
32 bit RISC Technology
SVM Sine wave PWM (Space Vector Modulation)
Software Implemented Current flux and Speed Regulators (Full DigitaI)
V/F
Sensorless Vector ( without encoder)
Vector with Encoder
1.25 / 2.5 / 5.0 / 10 kHz
0...1020 Hz for V / Hz Control
0...408 Hz for Vector Control
150% for 60 seconds every 10 minutes
180% for 1 second every 10 minutes
Greater than 97%
Regulation ( wilh Slip Compensation) : 1% 01 Motor Rated Speed
V / F Mode
Resolution: 1 rpm ( Keypad Reference )
Speed Regulation Range: 1: 20
Regulation: 0.5% of Motor Rated Speed
Sensorless
Resolution: 1 rpm (Keypad Reference)
Vector Mode
Speed Regulation Range: 1:100
Regulation with:
10 bit Analogy Reference: +1- 0.1% 01 Motor Rated Speed
Encoder Vector
14 bit Analogy Reference: +- 0.01% 01 Motor Rated Speed
Mode
Digital Reference (Ex: Keypad): + / - 0.01 % of Motor Rated Speed
Speed Regulation Range: Down to 0 rpm
Regulation: + - 10% of Motor Rated Torque
Vector Modes
Range: O ... 150% 01 Motor Rated Torque
2 Programmable Differential Input (10 bit) : 0...10 V 0...20 mA or 4...20 mA
1 Programmable Bipolar Input (14 bit): -10 ... + 10 V 0...20 mA or 4...20 mA <D
1 Programmable Isolated Input (10 bit) : O ... 10 V 0...20 mA or 4...20 mA <D
6 Programmable Isolated Input: 24 Vdc
1 Programmable Isolated Input: 24 Vdc
1 Programmable Isolated Input: 24 Vdc (for Motor PTC Thermistor)
1 Isolated Differencial Encoder Signals Output: 5 ...15 Vdc External Power Supply
RS-232 wilh KCS-GFW09 Kn <D - RS-485 Isolated with EBA or EBB Board <D
Protocolo Johnson Contols-N2 (optional)
Modbus RTU Standard, Profibus DP, DeviceNet, EtherNet / IP, DeviceNet Drive Profile with KFB kits.
D C Link Under Voltage
Output Short Circuit
D C Link Over Voltage
Output Ground Fault
Drive Over Temperature
External Fault
Motor Over Temperature
SeIf -diagnosis Fault
Output Over Current
Programming Error
Motor Overload (i x t)
Serial Communication Fault
Dynamic Braking Resistor Overload
Motor or Encoder Connection Fault
CPU / EPROM Error ( watchdog)
Power Supply Ohase Fault (30 A and above models)
Encoder Fault
Keypad Connection Fault
0ºC (32ºF)...40ºC (104ºF), up to 50ºC (122ºF) with 2% / ºC (1,1% / ºF) output current derating
5...90% Non Condensing
0...1000m (3300ft), up to 4000m (13100ft) with 10% / 1000m (3% / 1000ft) output current derating
Three-phase:
Elec tromagnetie Compatibil -Industrial Environment - EMC - Emission and Immunitv
low Voltage Directive
Semiconductor drive
Power Conversion Enuinment
Electronic Equipment for Use in Power Installations
Safety Requirements for Electrical Equipament for Measurement Control and laboratory Use
Underwriters laboratories Ine. USA
Phoenix Test-Lab GmbH – Germany (Competent Body)
Instituto Argentino de Normalización
Australian Communications Aulhority
Variable Speed Drives
19
www.weg.net
CFW-09 - Technical Data
Programming
Controls
KEYPAD
Monitoring
Standard
CONTROL FEATURES
AND OTPIONS
Options
General Drive Functions Programming
Start/Stop , Increase/Decrease Speed, JOG, FWD/REV and Local/Remote
Speed Reference (rpm)
Oulput Current (A)
Motor Speed (rpm)
Oulput Voltage (Vac)
Speed Proportional Value (Ex: ft/min)
Drive Status
Output Frequency (Hz)
Digital Inputs Status
DC Link Voftage (Vdc)
Transistor Outputs Status
Motor Torque (%)
Relay Outputs Status
Outout Power (kW)
Analog Inputs Value
Hours Powered Up (h)
Four Last Faults
Hours Enabled (h)
Fault Messages
Keypad wilh LCD + LED displays (HMI-CFW09-LCD)
Password to protect drive programming
LCD display language selection: English, Spanish and Portuguese
Control mode selection (via parameter}: V / F. Sensorless Vector or Vector with Encoder
Fault auto-diagnosis and auto-reset
Parameters reset to factory or user default
Drive Self-tuning to motor and load (Vector Modes)
Specific unit indication ( Ex: l/s, t/h, %, etc. )
Motor slip compensation (V / F Mode)
Manual and automatic Torque Boost (V / F Mode)
Adjustable V / F Curve (V / F Mode)
Minimum and maximum speed limits
Output current limit
Adjustable motor overload protection
Digital gain and offset adjustments for the analog inputs
Digital gain adjustment for the analog outputs
JOG function
JOG + I JOG - Function (momentary speed increase/decrease)
COPY Function (Drive ® Keypad or Keypad ® Drive)
Comparison functions for lhe digital outputs:
N* > Nx; N > Nx; N < Nx; N = O; N = N*; Is > Ix ; Is < Ix; T > Tx and T < Tx
Where: N = Motor speed; N* = Speed reference; Is = Output Current and T = Motor torque
Linear and S independent acceleration and deceleration ramps, two sets of ramps
DC Braking
Optimal Braking (Vector Modes)
Built-in dynamic braking transistor – Models up to 45A/220-230V and up to 30A/380-480V and up to 14A/500-600V
Multi-speed function (up to 8 preset speeds)
Speed Profiling function
Hour meter and Wattrneter
Overlapping PID Regulator (for automatic control of level, pressure, flow, etc. )
FWD I REV selection
Local I Remate operation selection
Flying Start function (restart with the motor spinning)
Skip Speed (critical speed rejection)
Ride-Through (operation during momentary power loss)
Built-in dynamic braking transistor:
Models: 6 ... 45 A / 220 - 230 V and 36 ... 30 A / 380 - 480 V
FieldBus communication: Modbus RTU built-in
Simplified keypad (with LED display only)
HMI-CFW09-LED
IP 55 Remote keypad (LED display only)
HMI-CFW09-LED-N4
IP 55 Remote keypad (LCD + LED displays)
HMI-CFW09-LCD-N4
Remote Keypad cable (3.3, 6.6,10.16.25 and 35 ft)
CAB - HMI 09-X
Blank Keypad for local lnstallation
TCL - CFW09
Blank Keypad for remote installation
TCR - CFW09
Remote Keypad frame kit
KMR - CFW09
EBA . OX - CFW09
EBB .OX.- CFW09
I/O Expansion Boards
EBC1 .OX- CFW10
EBE1. OX - CFW09
Profibus DP
KFB - PD
DeviceNet
KFB - DN
FieldBus Communications kits
(Mounted inside drive)
DeviceNet Drive Profile
KFB - DD
ElherNet I IP
KFB - EN
Software SUPERDRIVE
VSD I PC Communication kit
Conectores e Cabos
KSD - CFW09
KCS - CFW09
Intertace Serial Module RS-232
KCS - CFW09
Built-in dynamic braking transistor
Models: 54...130 A / 220-230 V and 38...142 A / 380-480 V
Models 180...600A/220-230V e 380-480V
Models 107...472A/500-690V
Models 100...428A/660-690V
Easy mounting kit wilh flange (for sizes 3...8)
Removable mounting kit (for slzes 9...10)
Inductor kit for DC link (for sizes 2...8)
EMC filter with high attenuation capacity
External dynamic
braking module
20
Variable Speed Drives
"DB" Models
DBW - 01
DBW - 02
KMF - CFW09
KME - CFW09
KIL - CFW09
RF
www.weg.net
CFW-09 - Sizing Table
CFW-09 DRIVE
Power Supply
Voltage
220 / 230V
380 / 400 / 415 /
440 / 460 / 480 V
500/600V
Part Number
CFW-09
0006 T 2223 E S
0007 T 2223 E S
0010 T 2223 E S
0013 T 2223 E S
0016 T 2223 E S
0024 T 2223 E S
0028 T 2223 E S
0045 T 2223 E S
0054 T 2223 E S
0070 T 2223 E S
0086 T 2223 E S
0105 T 2223 E S
0130 T 2223 E S
0003 T 3848 E S
0004T 3848 E S
0005 T 3848 E S
0009 T 3848 E S
0013 T 3848 E S
0016 T 3848 E S
0024 T 3848 E S
0030 T 3848 E S
0038 T 3848 E S
0045 T 3848 E S
0060 T 3848 E S
0070T 3848 E S
0086 T 3848 E S
0105 T 3848 E S
0142 T 3848 E S
0180T 3848 E S
0211 T 3848 E S
0240 T 3848 E S
0312 T 3848 E S
0361T 3848 E S
0450 T 3848 E S
0515 T 3848 E S
0600 T 3848 E S
0686 T 3848 E S
0855 T 3848 E S
0979 T 3848 E S
1140 T 3848 E S
1283 T 3848 E S
1468 T 3848 E S
1710 T 3848 E S
0002 T 5060 E S
0004 T 5060 E S
0007 T 5060 E S
0010 T 5060 E S
0012 T 5060 E S
0014 T 5060 E S
0022 T 5060 E S
0027 T 5060 E S
0032 T 5060 E S
0044 T 5060 E S
0053 T 5060 E S
0063 T 5060 E S
0079 T 5060 E S
Bullt-In
Dynamlc
Braking
MAXIMUM APPLlCABLE MOTOR
Rated Current (A)
CT*
Yes
Optional
Built-in
54
70
86
105
130
Optional
Built-in
36
45
54
70
86
105
130
174
180
211
240
312
361
450
515
600
0686
0855
0979
1140
1283
1468
1710
External DB
Module
Optional
Built-in
68
86
105
130
150
30
38
45
60
70
86
105
142
External DB
Module
Yes
230
3.6
4
5.5
9
13
16
24
Yes
Optional
Built-in
VT*
6
7
10
13
16
24
28
45
Voltage
(V)
2.9
4,2
7
10
12
14
22
27
32
44
53
63
79
4.2
7
10
12
14
14
27
32
32
53
63
79
99
400 / 415
525
Constant Torque
Variable Torque
KW
HP
KW
HP
1.1
1.5
2.2
2.2
3.7
5.5
7.5
11
15
18.5
22
30
37
1.1
1.5
2.2
4
5.5
7.5
11
15
18.5
22
30
37
45
55
75
90
110
132
160
200
260
300
350
355
500
560
630
710
800
1000
1,5
2,2
4.0
5.5
7.5
9.2
15
18.5
22
30
37
45
55
1.5
2
3
3
5
7.5
10
15
20
25
30
40
50
1.5
2
3
5.5
7.5
10
15
20
25
30
40
50
60
75
100
125
150
175
220
270
340
400
430
600
700
800
900
1000
1250
1500
2.0
3
5.5
7.5
10
12.3
20
25
30
40.2
50
60.3
73.7
1.1
1.5
2.2
2.2
3.7
5.5
7.5
11
18.5
22
30
37
45
1.1
1.5
2.2
4
5.5
7.5
11
18.5
22
22
37
45
55
55
90
90
110
132
160
200
260
300
370
355
500
560
630
710
800
1000
2,2
4.0
5.5
7.5
9.2
9.2
18.5
22
22
37
45
55
75
1.5
2
3
3
5
5.5
10
15
25
30
40
50
60
1.5
2
3
5.5
7.5
10
15
25
30
30
50
60
75
100
125
125
150
175
220
270
340
400
430
600
700
800
900
1000
1250
1500
2.0
2.95
3.0
7.40
10
12.3
20
25
30
40.2
50
60.3
73.7
Variable Speed Drives
Size
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
-
2
4
7
21
www.weg.net
CFW-09 - Sizing Table
CFW-09 INVERTER
Power Supply
Voltage
500/600V
500/600V
660 / 690 V
22
Part Number
CFW-09
0107 T 5060 E S
0147 T 5060 E S
0211 T 5060 E S
0247 T 5060 E S
0315 T 5060 E S
0343 T 5060 E S
0418 T 5060 E S
0472 T 5060 E S
0600 T 5060 E S
0652 T 5060 E S
0794 T 5060 E S
0897 T 5060 E S
0978 T 5060 E S
1191 T 5060 E S
1345 T 5060 E S
0002 T 5060 E S
0004 T 5060 E S
0007 T 5060 E S
0010 T 5060 E S
0012 T 5060 E S
0014 T 5060 E S
0022 T 5060 E S
0027 T 5060 E S
0032 T 5060 E S
0044 T 5060 E S
0053 T 5060 E S
0063 T 5060 E S
0079 T 5060 E S
0107 T 5060 E S
0147 T 5060 E S
0211 T 5060 E S
0247 T 5060 E S
0315 T 5060 E S
0343 T 5060 E S
0418 T 5060 E S
0472 T 5060 E S
0600 T 5060 E S
0652 T 5060 E S
0794 T 5060 E S
0897 T 5060 E S
0978 T 5060 E S
1191 T 5060 E S
1345 T 5060 E S
0492 T 6669 E S
0580 T 6669 E S
0646 T 6669 E S
0813 T 6669 E S
0869 T 6669 E S
0969 T 6669 E S
1220 T 6669 E S
0100 T 6669 E S
0127 T 6669 E S
0179 T 6669 E S
0225 T 6669 E S
0259 T 6669 E S
0305T 6669 E S
0340T 6669 E S
0428T 6669 E S
MAXIMUM APPLlCABLE MOTOR
Bullt-In
Dynamlc
Braking
CT*
VT*
External
107(100)
147(127)
211(179)
247(225)
315(259)
343 (305)
418(840)
472(428)
147(127)
196(179)
211(179)
315(259)
343(305)
418(340)
472(428)
555(428)
Rated Current (A)
Voltage
(V)
525
0600
0652
0794
0897
0978
1191
1345
Yes
Optional Built-in
Variable Speed Drives
External
DB Module
2.9
4,2
7
10
12
14
22
27
32
44
53
63
79
107(100)
147(127)
211(179)
247(225)
315(259)
343 (305)
418(840)
472(428)
4.2
7
10
12
14
14
27
32
32
53
63
79
99
147(127)
196(179)
211(179)
315(259)
343(305)
318(340)
472(428)
555(428)
600
0652
0794
0897
0978
1191
1345
0492
0580
0646
0813
0869
0969
1220
Optimal with
external unit
100
127
127
179
179
690
575
225
259
305
340
259
305
340
428
428
690
Constant Torque
Variable Torque
KW
HP
KW
HP
75
90
150
185
220
260
315
355
450
500
600
630
710
900
1120
1,5
2,2
3,7
5,5
7,5
11
15
18,5
22
30
37
45
55
75
110
150
185
220
250
300
370
450
490
635
710
750
970
1120
448
560
635
750
900
970
1120
90
110
160
200
250
280
315
400
100
147.5
201
248
295
350
422
475.7
600
650
850
950
1000
1300
1500
2
3
5
7,5
10
15
20
25
30
40
50
60
75
100
150
200
250
300
350
400
500
600
650
850
950
1000
1300
1500
600
750
850
1000
1200
1300
1500
125
150
220
275
350
370
430
500
90
132
150
220
260
315
355
400
450
500
600
630
710
900
1120
2,2
3,7
5,5
7,5
9,2
11
18,5
22
22
37
45
55
75
110
150
150
220
250
300
370
450(370)
450
490
635
710
750
970
1120
448
560
635
750
900
970
1120
110
160
160
250
280
315
400
400
100
147.5
201
248
295
350
422
475.7
600
650
850
950
1000
1300
1500
3
5
7,5
10
12,5
15
25
30
30
50
60
75
100
150
200
200
300
350
400
500
600
600
650
850
950
1000
1300
1500
600
750
850
1000
1200
1300
1500
150
220
220
350
370
430
500
500
Size
8E
10E
-
2
4
7
8E
10E
-
-
8E
10E
www.weg.net
CFW-09 - Part Number Specification
CFW09
0016
T
3848
P
O
00
SI
DB
A1
DN
H1
S3
Z
2 3
4
5
6
7
8
9
10
11
12
13
14
1
1 - CFW-09 VSD
2 - Output Rated Current for Constant Torque (CT) Sizing
220 - 230 V
380 - 480 V
500 - 600 V
500 - 690 V
660 - 690 V
3 - Power Supply: T = Three-phase
0006 = 6,0 A
0007 = 7 ,0 A
0010 = 10 A
0013 = 13 A
0016 = 16 A
0024 = 24 A
0028 = 28 A
0033 = 33 A
0038 = 38 A
0045 = 45 A
0054 = 54 A
0070 = 70 A
0086 = 86 A
0105 = 105 A 0130 = 130 A
0142 = 142 A
0180 = 180 A
0240 = 240 A
0361 = 361 A
0003 = 3,6 A
0004 = 4,0 A
0005 = 5,5 A
0009 = 9,0 A
0013 = 13 A
0016 = 16 A
0024 = 24 A
0030 = 30 A
0038 = 38 A
0045 = 45 A
0060 = 60 A
0070 = 70 A
0086 = 86 A
0105 = 105 A
0142 = 142 A
0180 = 180 A
0211 = 211 A
0240 = 240 A
0312 = 312 A
0361 = 361 A
0450 = 450 A
0515 = 515 A
0600 = 600 A
0686 = 686 A
0855 = 855 A
1140 = 1140 A
1283 = 1286 A
1710 = 1710 A
0002 = 2,9 A
0004 =4,2 A
0007 =7,0 A
0010 =10 A
0012 =12 A
0014 =14 A
0022 =22 A
0027 =27 A
0032 =32 A
0044 = 44 A
0053 = 53 A
0063 = 63 A
0079 = 79A
0107 = 0107A
0147 = 0147A
0211 = 0211A
0247 = 0247A
0315 = 0315A
0418 = 418A
0472 = 472A
0600 = 600A
0794 = 794A
0897 = 897A
0978 = 978A
1191 = 1191A
1345 = 1345A
0107 = 107 A
0147 = 147 A
0211 = 211 A
0247 = 247 A
0315 = 315 A
0343 = 343 A
0418 = 418 A
0472 = 472 A
0100 = 100 A
0127 = 127 A
0179 = 179 A
0225 = 225 A
0259 = 259 A
0305 = 305 A
0340 = 340 A
0428 = 428 A
4 - Power Supply Voltage: 2223 = 220 ... 230 VAC
3848 = 380 ... 480 VAC
5060 = 500 ... 600 VAC
6669 = 660 ... 690 VAC
5 - Languages:
P = Portuguese
E = English
G = German
S = Spanish
F = French
R = Russian
Sw = Swedish
6 - Product Version:
S = Standard
O = Optional
7 - Enclosure: 00 = Standard (see technical specifications table)
N4 = NEMA 4 x IP 56 (models up to 10HP)
8 - HMI - Human Machine Interface: 00 = standard (with HMI of LED´S + LCD)
SI = Without HMI
IL = Optional only with LED HMI
9 - Dynamic Braking: 00 = Standard
DB = With Built-in Dynamic Braking Transistor
RB = Regenative rectifying unit (models from
105A at 220V, and from 86A at 380-480V)
10 - Expansion Boards:
00 = Standard
A1 = EBA.01-CFW09 optional
A2 = EBA.02-CFW09 optional
A3 = EBA.03-CFW09 optional
B1 = EBB.01-CFW09 optional
B2 = EBB.02-CFW09 optional
B3 = EBB.03-CFW09 optional
B4 = EBB.04-CFW09 optional
11 - FieldBus Communications cards:
B5 = EBB.05-CFW09 optional
C1 = EBC1.01-CFW09 optional
C2 = EBC1.02-CFW09 optional
C3 = EBC1.03-CFW09 optional
E1 = Optional with EBE1.00 - CFW09
P1 = PLC1.01-CFW09 optional
P2 = PLC2.00-CFW09 optional
00 = Standard (not provided)
PD = KFB-PD optional (Profibus DP)
DN = KFB-DN optional (Device Net)
DD = Optional with KFB – DD
(Device Net Drive Profile / Special software)
EN = EtherNet / IP standard
12 - Special Hardware: 00 = not provided
H1...Hn = Special Hardware version-Optional
HD = Models from 105A at 220V, and from 86A at
380-480V are power supplied via DC link
HC/HV = The CFW09 VSDs mechanics from 2 to 8 have and inductor line for the DC link built into the product. To request the VSD with the inductor in place just add the code “HC” (for drives operating on Variable Torque).
13 - Special Software:
14 - Z = End of Code
00 = Standard software version
S1...Sn = Optional with version a special software SF = Protocol Metasys N2
SC = Hoist functions
SN = Winder I with power calculation
SQ = Special version for Kit Device Net Drive Profile
Example:
CFW09 0013 T 2223 E S Z
CFW09 0105 T 3848 E O IL A1 PD Z
CFW09 0086 T 3848 E O SI DB B2 MR S3 Z
Variable Speed Drives
23
www.weg.net
CFW-09 - Dimensions and Weight
NEMA 1 / IP 20
Height - H
mm
( in ) Width - W
SIZE
mm
( in )
1
143
(5.6)
2
182
(7.2)
290
(11.4)
3
223
(8.9)
390
(15.3)
4
250
(9.8)
475
(18.7) 550
(21.6) 335
(13.2)
5
6
7
8
210
(8.3)
675
(26.6)
835
(32.9)
975 (38.4)
(7.7)
41.9 (19.0)
274
(10.8)
(14.6)
(27.1)
1020
(40.2)
700
(27.5)
1185
(46.6)
49.6 (22.5)
90.4 (41.0)
370
688
13.2 (6.0)
(45.1) 9
Weight
lb ( kg )
7.7 (3.5)
(11.8)
(16.1)
10E
196
300
410
10
( in )
8E
1145
Depth - D
mm
121.3 (55.0)
154.3 (70.0)
220.5 (100.0)
253.0 (115.0)
492
476.2 (216)
(19.3)
571.0 (259)
582
(22.9)
682.0 (310.0)
CFW-09 Shark
CFW-09 Drives with Degree of Protection NEMA 4X (IP 56),
designed for highly aggressive environments including:
g Chemical industry
g Petrochemical
g Food industry
g Other applications requiring full protection to the electronic equipment.
380-480
220-230
POWER
SUPPLY
VOLTAGE
CFW-09 DRIVE
MODEL
CFW09...
0006 T 2223 P O N4 Z
0007 T 2223 P O N4 Z
0010 T 2223 P O N4 Z
0016 T 2223 P O N4 Z
0003 T 3848 P O N4 Z
0004 T 3848 P O N4 Z
0005 T 3848 P O N4 Z
0009 T 3848 P O N4 Z
0013 T 3848 P O N4 Z
0016 T 3848 P O N4 Z
Rheostatic
Braking
Standard
built-in to
the product
Standard
built-in to
the product
MAXIMUM APLICABLE MOTOR
Outlet rated current
(A)
CT*
VT*
6
7
10
16
3,6
4
5,5
9
13
16
Constant (CT*) / Variable (VT*)
Torque
Voltage
(V)
220
380
HP
Size
kW
1,5
2
3
5
1,5
2
3
5
7,5
10
1,1
1,5
2,2
3,7
1,1
1,5
2,2
3,7
5,5
7,5
1
2
1
2
*CT = Constant Torque (T load = CTE); VT = Variable Torque (e.g.: Quadratic Torque = > T load ~ n ²
Notes: 1 – Recommended motors 230/400VAC are based on WEG motors II and IV pode W21 line. For other polarity motors (e.g.: 6 and 8 poles), other (e.g.: 460V) and/or motors from other suppliers, specify the inverter based on nominal motor current.
2 – Models 6,7 and 10A/230V can be single-phase powered without output current derating.
Dimensions and Weight
NEMA 4X / IP 56
1
2
24
Variable Speed Drives
Height - H
Width - W
SIZE
mm
( in )
(9.2)
360
(14.2)
(10.2)
410
(16.2)
mm
(in)
234
280
Depth - D
mm
( in )
221 (8.5)
Weight
lb ( kg )
10 (22)
15 (33)
www.weg.net
CFW-09 - Special Functions
Multi-speed
Up to eight different speeds can be programmed by the user
and selected via the combination of three digital Inputs. These
Inputs can be switched by any external device such as Limit
Switches, Photocells, Proximity Sensors, PLC, etc.
Overlapping PID Regulator
DI
4
5
6
n1
0
0
0
n2
0
0
1
n3
0
1
0
n4
0
1
1
n5
1
0
0
n6
1
0
1
n7
1
1
0
n8
1
1
1
Outflow reference
or pressure reference
This built-in digital PID regulator was designed for applications
where a process variable (flow, pressure, level, etc.) has to be
controlled by the motor speed. To implement this regulator the
CFW-09 needs a set point and a feedback signal from the
process variable sensor so that a closed loop is formed. This
function eliminates the need for an external regulator to control
the process reducing the solution cost.
“S” Ramp
Velocidade (rpm)
This function replaces the traditional linear acceleration and
deceleration ramps by Type “S” Ramps providing smoother
starting, braking and approximation to the set speed curves.
The practical result is the elimination of mechanical shocks,
which are undesirable and some times unpractical for certain
applications.
Variable Speed Drives
25
www.weg.net
CFW-10
Designed for the control and speed variation of three-phase induction electric motors, the CFW-10 VSD combines
modern design with worldwide technology, where extreme compactness and easy programming stand out. With simple
installation and operation, this product comes with optimized software resources, through a local human-machine
interface, which enables it to be used in process controls and industrial machines.
Benefits
(V/F) Control
IP20 Finger-safe Enclosure
g Single-phase 110-127 input voltage up to 0.75 KW
g Single-phase 200-240 input voltage up to 2.2 KW
g Three-phase
g 150% current overload capacity
g DSP controlled PWM output
g 2.5 - 15 kHz ajustable switching frequency
g Four isolated programmable digital inputs
g Programmable relay output
g One isolated programmable analog input
g Diagnostic features: Overcurrent, motor overload, drive over temperature,
output short circuit, DC bus over and undervoltage and external fault
g Control features: Linear and “S” ramp acceleration and deceleration, local/
remote control, DC braking, torque boost, motor slip compensation,
electronic pot, preset speeds, maximum and minimum adjustable frequency
limits, adjustable output current limit, JOG
g Display readings: Motor speed, frequency, voltage, current, last fault,
heatsink temperature and drive status
g Ambient: 122ºF (50ºC), 3300ft (1000m) altitude, 90% humidity, non-condensing
for model 15,2A, 104°F (40°C).
g
g
Applications
Centrifugal pumps
Processing pumps
g Fans / Exhausters
g Stirrers / Mixers
Extruding Machines
Roller tables
g Driers
Rotating filters
Cutting machines
g Conveyors
g
g
g
g
g
g
Block diagram
Single Phase
or Three phase
power supply
Vdc
Standard and Plus Version
Plus Version
Relay Output
Programmable
 General
Isolated digital inputs
Isolated analog input
Standard, Plus and Clean Version
RFI Filter
Standard and Plus Version
Programmable
RUN
no fault
26
Variable Speed Drives
Fs = output frequency
Fe = input frequency
Fx = set frequency
Is = output current
Ix = set current
enable
 START/STOP
 On/Off
 FWD/REV
 Local/Remote
 Direction
rotation
of
 Multispeed
 Jog
 2nd
Ramp
 Reset
 No
external fault
 Electronic
potentiometer
www.weg.net
CFW-10 - Coding
CFW10
0040
S
2024
E
0
00
00
00
00
Z
2 3
4
5
6
7
8
9
10
11
1
1 - CFW-10 Variable Speed Drives
2 - Output rated current:
110-127 V
200-240 V
0016
1,6 A
0016
1,6A
0026
2,6 A
0026
2,6A
0040
4,0 A
0040
4,0A
3 - Number of phases
S = single-phase
T = Three - phase
0073
7,3A
0100
10,0A
0152
15,2A Only for three-phase model
4- Power Voltage Supply
1112 = 110-127 V (Single-phase only)
2024 = 200-240 V
5 -Manual Language
P = Portuguese
E = English
S = Spanish
6 -Options
S = standard
O = optional
7
Control card
00 = standard
CL = clean
PL = plus (with potentiometer)
8- EMC Buit-in filter
00 = (not avaliable)
FA = with EMC filter (class A) –
Only for single-phase models (200-240V) models
9
Special hardware
00 = not provided
Hx = special hardware in version X
CP = Cold Plate heatsink version
10 - Special software
00 = not provided
Sx = special software in version X
11 - End of code
Ex.: CFW100040S2024ESZ
VSD of CFW-10 series, 4.0 A, single -phase
at 200-240 VAC and manual in English.
Variable Speed Drives
27
www.weg.net
CFW-10 - Specification Table
Power
Supply
Voltage
Variable Speed Drives CFW-10
Power
Supply
110-127
Single
phase
200-240
Three phase
Maximum Applicable Motor
In Output
(A)
Size
HP
kW
CFW100016S1112ESZ
1,6
1
0.25
0.25
CFW100026S1112ESZ
2,6
1
0.5
0.55
Voltage (V)
CFW100040S1112ESZ
4.0
2
1.0
0.75
CFW100016S2024ESZ
1.6
1
0.25
0.25
CFW100026S2024ESZ
2.6
1
0.5
0.55
CFW100040S2024ESZ
4.0
1
1.0
0.75
CFW100073S2024ESZ
7.3
2
CFW100100S2024ESZ
10
3
230
Dimensions (mm)
Power rating
Model
H
W
D
132
95
121
0.9
161
115
122
1.5
132
95
121
0.9
115
122
95
121
0.9
122
1.5
122
1.8
2.0
1.5
161
3.0
2.2
191
CFW100016T2024ESZ*
1.6
1
0.25
0.25
CFW100026T2024ESZ*
2.6
1
0.5
0.55
CFW100040T2024ESZ*
4
1
1.0
0.75
Weight
(Kg)
132
CFW100073T2024ESZ*
7.3
1
2.0
1.5
CFW1000100T2024ESZ*
10
2
3.0
2.2
161
CFW1000152T2024ESZ*
15.2
3
5.0
4
191
115
1.5
1.8
NOTES: The maximum motor power ratings listed above were based on WEG II and IV-pole motors.
For motors with different numbers of poles (ex.: VI and VIII-poles), other voltages (ex.: 230V) and/or motors from other manufacturers, specify the VSD
through the motor rated current.
* CE Certification pending.
CFW-10 - Specification Table “Cold Plate”
Power
Supply
Voltage
Variable Speed Drives CFW-10
Power
Supply
110-127
Single
phase
200-240
Three
phase
Model
In Output
(A)
Size
CFW100016S1112EOCPZ
1,6
CFW100026S1112EOCPZ
2,6
Voltage (V)
Dimensions (mm)
Power rating
HP
kW
1
0.25
0.18
1
0.5
0.37
CFW100040S1112EOCPZ
4.0
2
1.0
0.75
CFW100016S2024EOCPZ
1.6
1
0.25
0.18
CFW100026S2024EOCPZ
2.6
1
0.5
0.37
W
132
100
0.7
161
120
1.0
132
100
0.7
CFW100040S2024EOCPZ
4.0
1
1.0
0.75
7.3
2
2.0
1.50
161
CFW100100S2024EOCPZ
10
3
3.0
2.20
191
CFW100016T2024EOCPZ*
1.6
1
0.25
0.18
CFW100026T2024EOCPZ*
2.6
1
0.5
0.37
CFW100040T2024EOCPZ*
4.0
1
1.0
0.75
1.5
230
132
CFW100073T2024EOCPZ*
7.3
1
2.0
CFW1000100T2024EOCPZ*
10
2
3.0
2.2
161
CFW1000152T2024EOCPZ*
15.2
3
5.0
3.70
191
Variable Speed Drives
120
100
120
D
Weight
(Kg)
H
CFW100073S2024EOCPZ
* CE Certification pending.
28
Maximum Applicable Motor
82
1.0
1.2
0.7
1.0
1.2
www.weg.net
CFW-10 - Technical Data
Model
POWER SUPPLY
ENCLOSURE
Single-phase
Voltage
Single-phase or
Three-phase
Frequency
Cos ϕ (Displacement Power Factor)
Degree of Protection
Electronic Power Supply
Temperature
Humidity
Altitude
Color
Opaque gray - WEG development 205E1404
Switching Frequency
Frequency Range
Frequency Setting Resolution
Output Frequency Accuracy
Overload capacity
CONTROL INPUTS
Analog
Digital
CONTROL OUTPUTS
SAFETY
Relay
Protections
Programming
Commands
KEYPAD (HMI)
Monitoring (reading)
AMBIENT
ENCLOSURE
CONFORMITIES
CONTROL
FEATURES
200 - 240VAC: 200 / 220 / 230 / 240VAC (+10%, -15%)
50 / 60 Hz +/- 2 Hz (48 - 62 Hz)
> 0.98
IP 20
Switching power supply
Sinusoidal PWM modulation (Space Vector Modulation),
Linear V/F or quadratic V/F
Frequencies: from 2.5 KHZ up to 15 KHZ
0 - 300 Hz
Analog Ref.: 0.1% of max. frequency and Digital ref.: 0.01 Hz (f<100Hz); 0.1Hz (f>100Hz)
Analogue Ref.: 0.5% and Digital Ref.: 0.01%
150% during 60 sec. every 10 min. (1.5 x In - Rated Current)
1 programmable isolated
1 programmable isolated
Input 0 -10VDC, 0 - 20mA or
Input 0 -10VDC, 0 - 20mA or
4 - 0mA
4 - 0mA
4 programmable isolated inputs 12 Vdc
1 programmable output, form
1 programmable output, form
C Contacts (NO/NC)
C Contacts (NO/NC)
Programming Options: Is > Ix ; Fs > Fx ; Fe > Fx ; Fs = Fe ; Run; No Fault
DC Link Overvoltage / Undervoltage
VSD Over temperature
Keypad Connection Fault
Motor Overload ( i x t )/ Output Short Circuit
CPU Error (Watchdog), External Fault
Output short-circuit
Programming Error
--- / Self-diagnosis Error
Start/Stop, (General functions programming)
Start/Stop / Frequency Increases / Decreases Speed
Variable speed potentiometer
Output Frequency (Hz)
DC Link Voltage (VDC)
Speed proportional value (Ex: tt/min)
Heat sink temperature
Output Current (Amps)
Output Voltage (Volts)
Last Fault Messages
0...122ºF (0 ... 50 °C) - 0...104°F (0...40°C) for 15,2A mode
5 ... 90% non condensing
0...3300ft (1000 m) up to (4000 m) with 10%/1000m output current de-rating
Control Method
CONTROL
CFW-10 Standard
CFW-10 Clean
CFW-10 with potentiometer
110 - 127VAC: 110 / 127VAC (+10%, -15%)
Electromagnetic Compatibility
EMC directive 89 / 336 / EEC
EN 61800-3
Low Voltage
LVD 73/23/EEC - Low Voltge Directive / UL 508C
Standard
Keypad with 7 segment displays (LED’s)
Password to protect VSD Programming
Fault Auto-diagnosis and automatic reset
Motor Slip compensation (V/F mode)
Manual and automatic torque boost (I x R)
Linear and “S” independent acceleration ramp, two sets of ramps
JOG function
DC braking
Multi-Speed function (up to 8 pre programmable speeds)
Forward/Reverse Speed Selection via DI
Local/Remote Reference Selection via DI
Variable Speed Drives
29
www.weg.net
Drive Comparison
CFW-08
single-phase
Voltage
3-phase voltage
200 - 240V:200/220/230/240 V
(+10%, -15%)
-
200 - 240V:200/220/230/240 V
(+10%, -15%)
380 - 480V : 380/400/415/440/460/ 480V
(+10%, -15%)
220 - 230V:220/230V
(+10%, - 15%)
380 - 480V : 380/400/415/
440/460/480V (+10%, -15%)
Power Supply
500 - 600V:500/525/575/600V
(+10%, -15%)
Frequency
Cos φ
(displacement
power factor)
Drive
Remote MMI
Flange mounted
Braking IGBT
Supply type
Control
Control type
Switching
Control
Speed variation
permitted
overload
Efficiency
speed control
Control VVW
Performance
speed control
speed control
Torque Control
500 - 600V:500/525/575/600V
(+10%, -15%)
500 - 690V:500/525/575/600/690V
(+10%, - 15%)
50 / 60 Hz +/- 2 Hz (48 ... 62Hz)
CFW-10
110-127V: 110/127 V (+10 %, -15%)
200-240V: 200/220/230/240 V
(+10%, -15%)
200-240V: 200/220/230/240 V
(+10%, -15%)
Greater than 0,98
Power factor
Degree of
Protection
models
CFW-09
Nema 1 on mechanical size 3 and 4 and
IP 20 on mechanical size 1 and 2
Nema 1 with additonal metallic
conduit connection kit
NEMA12 Parallel, remote MMI (IP54)
(MMI-CFW08-RP)
NEMA12 Serial, remote MMI (IP54)
(MMI-CFW08-RS)
Size 2, 3 and 4
NEMA 1 / IP20
(Size 1...8)
IP20
(Size 9...10)
NEMA 4x / IP 56
IP 20
-
Yes
mechanical models 1 and 2 standard,
Size 2, 3 and 4
Size 2 and 3
optional for mechanical size 8 and 10
Switched Mode Power Supply
V/F (scalar) linear or quadratic
V/F (scalar)
VVW
Sensorless vector control
V/F (scalor) linear or quadratic
(Voltage Vector-Control WEG)
(Voltage Vector-Control WEG)
Sensorless vector (without encoder)
Vector with encoder
Available frequencies
Available frequencies
Available frequencies
2,5 / 5,0 / 10 / 15 kHz
1.25/ 2.5 / 5.0 / 10 kHz
2.5 up to 15 kHz
0...204Hz (Supply frequency 60Hz)
Band Range : 0 ... 300 Hz
0...170Hz (Supply frequency 50Hz)
Band Range : 0 ... 300 Hz
Above 204 Hz (please contact WEG)
CT: 150% for 60 seconds every 10 minutes
150% for 60 seconds every 10 minutes
150% for 60 seconds every 10 minutes
VT: 110 to 120% for 60 seconds
(1,5 x Inom.)
every 10 minutes
greater than 0,95 %
98%
greater than 0,95 %
V/F Setting: 1% Rated Speed with
V/F Setting: 1% Rated Speed with
V/F Setting: 1% Rated Speed with
Slip Compensation
Slip Compensation
Slip Compensation
Resolution: 0.01 Hz (f<100Hz); 0.1
Resolution; 1 rpm (keypad reference)
Resolution: 0.01 Hz (f<100Hz); 0.1
Hz(f<100Hz) (keypad reference)
regulation rate = 1:20
Hz(f<100Hz) (keypad reference)
Regulation; 0.5% of the rated speed.
Regulation; 0.5% of the rated speed.
Resolution; 1 rpm (keypad reference)
Resolution; 1 rpm (keypad reference)
regulation rate = 1:30
Regulation; 0.5% of the rated speed.
Resolution; 1 rpm (keypad reference)
regulation rate = 1:100
10 bit analog reference setting: +/0.01% Rated Speed: with 14-bit analog
reference +/-0.01% Rated Speed: with
digital reference
Rate: Up to 0
Setting: +/- 10% (sensorles) +/- 5%
(encoder) motor Rated torque
Setting: 0...150% (encoder)
motor Rated torque
Variable Speed Drives
www.weg.net
Drive Comparison
models
CFW-08
CFW-09
CFW-10
4 programmable isolated digital inputs 6 programmable inputs, optoisolated,
with NPN or PNP logic (DI1...DI4)
bidirectional, 24Vdc
PTC isolated inputs via AI and AI2
2 outputs with reverser contacts
Digital
4 programable isolated inputs
Programmable isolated inputs via AI1 and
(NO/NC) and 1
AI2 with NPN or PNP logic (DI5 and DI6) output with NO contact, programmable
2 programmable outputs,
programmable 2-output relay, reversible
1 programable output, reversal
NO/NC contacts
Relay
2 programmable outputs,
contacts (NO/NC)
NO/NC contacts
Inputs and
NO/NC contacts
2 isolated analog inputs
2 programmable differential inputs,
Outputs
0...10V/ 4...20mA / -10 ...10V, 8 bits
10 bits
2 programmable outputs, 0 a 10V,
11 bits
1 isolated input 0...10 V, 0...20 mA
2 programmable outputs bipolares
Analog
1 isolated input 0 ...10V,
or 4...20 mA
(-10...10V),
(0)4 ... 20mA, 8 bits
14 bits (optional)
2 programmable outputs isoladas,
11 bits (optional)
RS - 232 via serial kit
KCS - CFW09
Serial Interface
RS-232 or RS-485
RS - 485, isolated, via EBA or
EBB RS-485 cards (accesory)
Communication
Profibus DP unit for communication RTU ModBus via Profibus DP, DeviceNet
FieldBus networks (optional) and DeviceNet or CANopen or or DeviceNet Profile serial interface via
RTU ModBus (built-in)
additonal KFB kit
Overvoltage and undervoltage in intermediary circuit
overheating in the inverter and motor
inverter overheating
output overcurrent
motor overload ( i x t )
Hardware error, external defect or
braking resistor overload
Hardware Error, external fault.
serial communication error
output short-circuit and output ground
CPU error (Watchdog)
EPROM output short-circuit
short-circuit
Programming error and
Safety
Protections
incremental encoder failure
Programming Error
self-adjusting error
output short-circuit
output ground short-circuit
External Error
autodiagnosing and programming error
serial communication failure
inverted motor / encoder connection
Power Supply Phase Fault
MMI-CFW09 interface failure
0...40 ºC (up to 50 C with reduction of 0...40 ºC (up to 50 C with reduction of
0...50 ºC (without reduction in
temperature
2%/ º C in the output current)
2%/ º C in the output current)
the output current)
Ambient
humidity
5...90% without condensation
5...90% without condensation
5...90% without condensation
conditions
0.....1000 m (up to 4000 m with
0.....1000 m (up to 4000 m with
0.....1000 m (up to 4000 m with
altitude
1% / 100 m in the output current)
1% / 100 m in the output current)
1% / 100 m in the output current)
on/off, Setting Parameters (general programming)
increase / decrease frequency
control
JOG, invertion of rotation direction and local / remote potentiometer
Variable speed potentiometer
selection for speed control
motor output frequency
intermediate circuit voltage
inverter status
intermediate circuit voltage
Human-Machine
frequency proportional value
digital input and output status
Speed proportional value
Interface
Heat sink temperature
motor speed
Heat sink temperature
(HMI)
Monitoring
motor output current (A)
motor output voltager (V)
(reading)
error messages / output power defects
load torque
relay output status
inverter status
Built-in in frame size 1,2 optional in
rheostatic braking
Built-in in frame size 2,3,4
Built-in frame size 2,3
frame size 3,4,5,6,7
CC braking
built-in
built-in
built-in
functions
Optimal Braking
built-in
+24 Vdc source
available
PID
built-in
built-in
built-in
Variable Speed Drives
31
WEG Worldwide Operations
AUSTRALIA
WEG AUSTRALIA PTY. LTD.
3 Dalmore Drive
Carribean Park Industrial Estate
Scoresby VIC 3179 - Melbourne
Phone(s): 61 (3) 9765 4600
Fax: 61 (3) 9753 2088
info-au@weg.net
www.weg.net/au
BELGIUM
WEG BENELUX S.A.
Rue de l’Industrie 30 D,
1400 Nivelles
Phone(s): + 32 (67) 88-8420
Fax: + 32 (67) 84-1748
info-be@weg.net
www.weg.net/be
CHILE
WEG CHILE S.A.
Los Canteros 8600
La Reina - Santiago
Phone(s): (56-2) 784 8900
Fax: (56-2) 784 8950
info-cl@weg.net
www.weg.net/cl
CHINA
WEG (NANTONG) ELECTRIC
MOTOR MANUFACTURING CO.,
LTD.
No. 128# - Xinkai South Road,
Nantong Economic &
Technical Development Zone,
Nantong, Jiangsu Province.
Phone(s): (86) 0513-85989333
Fax: (86) 0513-85922161
info-cn@weg.net
www.weg.net/cn
COLOMBIA
WEG COLOMBIA LTDA
Calle 46A N82 - 54
Portería II - Bodega 7 - San
Cayetano II - Bogotá
Phone(s): (57 1) 416 0166
Fax: (57 1) 416 2077
info-co@weg.net
www.weg.net/co
FRANCE
WEG FRANCE SAS
ZI de Chenes – Le Loup
13 Rue du Morellon – BP 738
38297 Saint Quentin Fallavier
Phone(s): +33 (0) 4 74 99 11 35
Fax: +33 (0) 4 74 99 11 44
info-fr@weg.net
www.weg.net/fr
GERMANY
WEG GERMANY GmbH
Alfred-Nobel-Str. 7-9
D-50226 Frechen
Phone(s): +49 (2234) 9 5353-0
Fax: +49 (2234) 9 5353-10
info-de@weg.net
www.weg.net/de
INDIA
WEG Electric (India) Pvt. Ltd.
#38, Ground Floor, 1st Main
Road, Lower Palace Orchards,
Bangalore – 560 003
Phone(s): +91-80-4128 2007
+91-80-4128 2006
Fax: +91-80-2336 7624
info-in@weg.net
www.weg.net/in
ITALY
WEG ITALIA S.R.L.
V.le Brianza 20 - 20092 - Cinisello
Balsamo - Milano
Phone(s): (39) 02 6129-3535
Fax: (39) 02 6601-3738
info-it@weg.net
www.weg.net/it
JAPAN
WEG ELECTRIC MOTORS
JAPAN CO., LTD.
Matsumoto Bldg. 2F, 3-23-7
Kamata, Ohta-ku,
Tokyo, Japan 144-0052
Phone(s): (81) 3 3736-2998
Fax: (81) 3 3736-2995
info-jp@weg.net
www.weg.net/jp
MEXICO
WEG MEXICO, S.A. DE C.V.
Carretera Jorobas-Tula Km. 3.5,
Manzana 5, Lote 1
Fraccionamiento Parque
Industrial - Huehuetoca,
Estado de México - C.P. 54680
Phone(s): + 52 (55) 5321 4275
Fax: + 52 (55) 5321 4262
info-mx@weg.net
www.weg.net/mx
WEG Equipamentos Elétricos S.A.
International Division
Av. Prefeito Waldemar Grubba, 3000
89256-900 - Jaraguá do Sul - SC - Brazil
Phone:55 (47) 3276-4002
Fax: 55 (47) 3276-4060
www.weg.net
NETHERLANDS
WEG NETHERLANDS
Sales Office of
WEG Benelux S.A.
Hanzepoort 23C
7575 DB Oldenzaal
Phone(s): +31 (0) 541-571080
Fax: +31 (0) 541-571090
info-nl@weg.net
www.weg.net/nl
PORTUGAL
WEG EURO - INDÚSTRIA
ELÉCTRICA, S.A.
Rua Eng. Frederico Ulrich
Apartado 6074
4476-908 - Maia
Phone(s): +351 229 477 705
Fax: +351 229 477 792
info-pt@weg.net
www.weg.net/pt
RUSSIA
WEG RUSSIA
Pochainskaya Str. 17
Nizhny Novgorod
603001 - Russia
Phone(s): +7-831-2780425
Fax: +7-831-2780424
info-ru@weg.net
www.weg.net/ru
SPAIN
WEG IBERIA S.L.
Avenida de la Industria,25
28823 Coslada - Madrid
Phone(s) : (34) 916 553 008
Fax : (34) 916 553 058
info-es@weg.net
www.weg.net/es
SINGAPORE
WEG SINGAPORE PTE LTD
159, Kampong Ampat,
#06-02A KA PLACE.
Singapore 368328.
Phone(s): +65 6858 9081
Fax: +65 6858 1081
info-sg@weg.net
www.weg.net/sg
UK
WEG ELECTRIC
MOTORS (U.K.) LTD.
28/29 Walkers Road
Manorside Industrial Estate
North Moons Moat - Redditch
Worcestershire B98 9HE
Phone(s): 44 (01527) 596-748
Fax: 44 (01527) 591-133
info-uk@weg.net
www.weg.net/uk
UNITED ARAB EMIRATES
WEG MIDDLE EAST FZE
JAFZA – JEBEL ALI FREE ZONE
Tower 18, 19th Floor,
Office LB181905
Dubai – United Arab Emirates
info-ae@weg.net
www.weg.net/ae
USA
WEG ELECTRIC CORP.
1327 Northbrook Parkway,
Suite 490
Suwanee 30024
Phone(s): 1-770-338-5656
Fax: 1-770-338-1632
info-us@weg.net
www.weg.net/us
VENEZUELA
WEG INDUSTRIAS VENEZUELA C.A.
Avenida 138-A
Edificio Torre Banco Occidental de
Descuento, Piso 6 Oficina 6-12
Urbanizacion San Jose de Tarbes
Zona Postal 2001
Valencia, Edo. Carabobo
Phone(s): (58) 241 8210582
(58) 241 8210799
(58) 241 8211457
Fax: (58) 241 8210966
info-ve@weg.net
www.weg.net/ve
SWEDEN
WEG SCANDINAVIA AB
Box 10196
Verkstadgatan 9
434 22 Kungsbacka
Phone(s): (46) 300 73400
Fax: (46) 300 70264
info-se@weg.net
www.weg.net/se
ZEST ELECTRIC MOTORS (PTY) LTD.
47 Galaxy Avenue, Linbro Business Park - Gauteng Private Bag X10011
Sandton, 2146 Johannesburg - JOHANNESBURG - SOUTH AFRICA
Phone(s): (27-11) 723-6000
Fax: (27-11) 723-6001
E-mail: info@zest.co.za
www.zest.co.za
1034.03/092009 - The values shown are subject to change
without prior notice. The information is for reference only.
ARGENTINA
WEG EQUIPAMIENTOS
ELECTRICOS S.A.
(Headquarters San
Francisco-Cordoba)
Sgo. Pampiglione 4849
Parque Industrial San Francisco
2400 - San Francisco
Phone(s): +54 (3564) 421484
Fax: +54 (3564) 421459
info-ar@weg.net
www.weg.net/ar
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising