Yamaha | PianoCraft E-410 | Specifications | Yamaha PianoCraft E-410

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
ii
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this unit (RX-E410 and CDX-E410) in a well ventilated,
cool, dry, clean place with at least 10 cm on the top (except for
CDX-E410), 10 cm on the left and right, and 10 cm at the back of
this unit — away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold.
Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
Do not plug in this unit to a wall outlet until all connections are
complete.
Do not operate this unit upside-down. It may overheat, possibly
causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of this
unit with a voltage other than specified.
Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed.
The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
Before moving this unit, press STANDBY/ON to set this unit in
standby mode, and disconnect the AC power plug from the wall
outlet.
Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave the unit alone.
When using the unit for a long time, the unit may become warm.
Turn the power off, then leave the unit alone for cooling.
Install this unit near the wall outlet and where the AC power plug
can be reached easily.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit itself
is turned off. This state is called the standby mode. In this
state, this unit is designed to consume a very small quantity of
power.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
DANGER
When this unit is plugged to the wall outlet, do not place your
eyes close to the opening of the disc tray and other openings to
look into inside.
The laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to
the terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L
or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
Contents
OTHER OPERATIONS
Features .................................................................. 2
Supplied Accessories ............................................. 2
Controls and Functions ......................................... 3
Setting the Timer.................................................. 32
Receiver (RX-E410) .................................................. 3
CD player (CDX-E410)............................................. 6
Remote control........................................................... 8
Setting the auto-standby mode............................ 34
Controlling iPod ................................................... 35
Setting the clock timer ............................................. 32
Setting the sleep timer ............................................. 33
Available iPod operations........................................ 35
Using iPod ............................................................... 36
Connecting the System ........................................ 12
Connecting Antennas .......................................... 14
Connecting the AM loop antenna ............................ 14
Connecting the FM antenna..................................... 14
Connecting External Components ..................... 15
ADDITIONAL INFORMATION
Troubleshooting.................................................... 38
Receiver (RX-E410) ................................................ 38
CD player (CDX-E410)........................................... 41
Remote control ........................................................ 41
Notes on Discs ....................................................... 42
Connecting the Power Cables............................. 17
Adjusting the Clock ............................................. 18
Glossary................................................................. 43
Disc information ...................................................... 42
Handling a disc ........................................................ 42
Audio information ................................................... 43
Copyright and logo marks ....................................... 43
Specifications ........................................................ 44
BASIC OPERATIONS
BASIC
OPERATIONS
Connecting an MD player or a tape deck ................ 15
Connecting an MD recorder or a CD recorder ........ 15
Connecting a YAMAHA iPod universal dock ........ 16
PREPARATION
PREPARATION
INTRODUCTION
INTRODUCTION
Basic Receiver Operations .................................. 19
Changing the front panel display settings................ 20
Basic Disc Playback Operations......................... 21
TUNER
OPERATIONS
Switching the playback information display ........... 22
Repeating playback
(Repeat Play) ....................................................... 24
Playing back randomly
(Random Play)..................................................... 24
Customizing playback order (Program Play) .......... 25
TUNER OPERATIONS
OTHER
OPERATIONS
FM/AM Tuning.................................................... 26
Automatic tuning ..................................................... 26
Manual tuning.......................................................... 26
Automatic preset tuning........................................... 27
Manual preset tuning ............................................... 27
Selecting preset stations........................................... 28
Radio Data System Tuning (U.K. and Europe
Models Only) .................................................... 29
ADDITIONAL
INFORMATION
Selecting the Radio Data System program .............. 29
Displaying the Radio Data System information ...... 30
English
1 En
FEATURES
Features
Receiver (RX-E410)
• Maximum RMS output power per channel
65W + 65W (1% THD, 1 kHz, 6Ω)
• 40-station FM/AM preset tuning
• iPod dock terminal
• Pure Direct mode
CD player (CDX-E410)
• Plays Audio CDs, MP3 CDs, and WMA CDs.
• CD Text data display
• Optical and coaxial digital output jacks
■ About this manual
• In this manual, “RX-E410” is described as “receiver” and “CDX-E410” is described as “CD player”.
• This manual describes how to operate the system using a remote control except when it is not available. Some of these operations are
also available using the front panel buttons.
• y indicates a tip for your operation.
• Notes contain important information about safety and operating instructions.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and the product, the product has priority.
Supplied Accessories
This product includes the following accessories. Before connecting this system, make sure you received all of the following parts.
Remote
control
Batteries (x2)
(AA, R06, UM-3)
System control
cable (0.6 m)
STANDBY/ON
1
2
3
4
5
6
7
8
9
0
DIMMER
FREQ/TEXT
PROG
Indoor FM antenna
REPEAT
MODE
PTY SEEK
START
RANDOM
TIME/INFO
FOLDER/PRESET
FILE
/A-E
ENTER
INPUT
MENU
FILE
/A-E
VOLUME
DISPLAY
SLEEP
2 En
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
Audio pin
cable (1.5 m)
AM loop antenna
Controls and Functions
INTRODUCTION
Receiver (RX-E410)
■ Front panel
1 2
3 45
6
7
8
9
NATURAL SOUND STEREO RECEIVER RX-E410
PURE DIRECT
DISPLAY
TIMER
MEMORY
AUTO/MAN'L
TIME ADJ
TIMER
PRESET/BAND
PRESET/TUNING
VOLUME
BASS
STANDBY/ON
TREBLE
HOUR
MIN
INPUT
BALANCE
PHONES
L
R
MIN
0 A
B
C
1 STANDBY/ON
Turns the receiver on or sets it to the standby mode.
2 Remote control sensor
Receives signals from the remote control.
3 DISPLAY
Switches the information shown in the front panel display
(see page 20).
4 Front panel display
Shows the various infomaiton such as the clock time or the
tuning frequency.
5 MEMORY (TIME ADJ)
• Stores a preset station in the memory. Hold down this
key for more than 2 seconds to preset radio stations
automatically (see page 27).
• Sets the clock before using the timer function (see
page 18).
6 AUTO/MAN’L (TIMER)
• Switches between Automatic Tuning mode and Manual
Tuning mode when tuner is selected as an input source (see
page 26).
• Turns the clock timer function on or off (see page 32).
D
E
MAX
F
8 PRESET/TUNING d / u (HOUR, MIN)
Selects a tuning frequency when tuner is selected as an
input source.
9 PURE DIRECT
Turns on or off the Pure Direct mode (see page 19).
0 TIMER indicator
Lights up when the clock timer is on (see page 32).
A PHONES
Outputs audio signals for private listening with headphones.
B BASS
Adjusts the low frequency responce (see page 19).
C TREBLE
Adjusts the high frequency responce (see page 19).
D BALANCE
Adjusts the volume level of each left and right speaker
channel (see page 19).
E INPUT
Selects an input source.
F VOLUME
Adjusts the volume level.
English
7 PRESET/BAND
Switches between FM, AM, and the preset mode when
tuner is selected as an input source.
3 En
Controls and Functions
■ Rear panel
1
2
3
ANTENNA
75
UNBAL.
SPEAKERS
(Europe model)
MAINS
6 MIN / SPEAKER
DOCK
FM
CD
AC OUTLETS
SWITCHED
R
L
GND
IN
OUT
TAPE/MD
AM
SUBWOOFER
OUT
TO CDX-E410
AUX
R
4
5
100W MAX. TOTAL
L
6
1 DOCK terminal
Use to connect a YAMAHA iPod universal dock (such as
YDS-10 sold separately) where your iPod can be stationed
(see page 16).
2 Antenna terminals
See page 14 for connection information.
3 Speaker terminals
See page 13 for connection information.
4 CD jacks
See page 12 for connection information.
5 TAPE/MD IN/OUT jacks
See page 15 for connection information.
4 En
7
8
9
6 AUX jacks
Use to connect the external components.
7 SUBWOOFER OUT jack
Use to connect the subwoofer.
8 System connector (TO CDX-E410) jack
See page 12 for connection information.
9 AC OUTLET(S)
See page 17 for connection information.
Controls and Functions
■ Front panel display
2
3
4
SLEEP PRESET STEREO AUTO
TIMER
TUNED MEMORY
5
6
7
8
INTRODUCTION
1
DOCK SHUFFLE REPEAT PS PTY RT CT PTY HOLD
PLAYLISTS ARTISTS ALBUMS SONGS GENRES
D
9
0
A
B
1 SLEEP indicator
Lights up when the sleep timer is on (see page 33).
2 PRESET indicator
Lights up when you preset radio stations manually (see
page 27).
3 STEREO indicator
Lights up when the receiver is receiving a strong signal
from an FM stereo broadcast.
4 AUTO indicator
Lights up when the receiver is in the Automatic Tuning
mode (see page 26).
5 DOCK indicator
Lights up when you station your iPod in a YAMAHA iPod
universal dock (such as YDS-10 sold separately)
connected to the DOCK terminal of the receiver (see
page 16).
C
9 Multi-information display
Shows the various infomaiton such as the clock time or the
tuning frequency.
0 TIMER indicator
Flashes when the the receiver is in the clock timer setting
mode (see page 32).
A TUNED indicator
Lights up when the receiver is tuned into a station.
B MEMORY indicator
Lights up or flashes when you preset radio stations.
C iPod menu indicators
Light up the iPod menu currently selected (see page 36).
D iPod operation indicators
Show operable cursor keys when operating the iPod menu
with the menu browse mode (see page 36).
6 SHUFFLE indicator
Lights up when you set your iPod in shuffle mode.
7 REPEAT indicator
Lights up when you set your iPod in repeat mode.
8 Radio Data System indicators
The name of the Radio Data System data offered by the
currently received Radio Data System station lights up.
PTY HOLD indicator
Lights up when the receiver is seaching for the Radio Data
System stations in the PTY SEEK mode (see page 29).
English
5 En
Controls and Functions
CD player (CDX-E410)
■ Front panel
1
2
NATURAL SOUND COMPACT DISC PLAYER
3
4
CDX-E410
STANDBY/ON
5
1 Disc tray
Holds a disc to be played back.
2
Opens and closes the disc tray.
3 s
Stops playback (see page 21).
4 h/e
Starts or pauses playback (see page 21).
5 STANDBY/ON
Turns the CD player on or sets it to the standby mode.
6 En
6
7
8
6 Front panel display
Shows the current status of the CD player.
7 b/w
Skips to the begining of the current track. Press and hold
to fast reverse (see page 21).
8 f/a
Skips to the next track. Press and hold to fast forward (see
page 21).
Controls and Functions
■ Rear panel
INTRODUCTION
MAINS
LINE OUT
DIGITAL OUT
L
OPTICAL
COAXIAL
2
3
TO RX-E410
R
1
4
1 LINE OUT jacks
See page 12 for connection information.
2 OPTICAL jack
See page 15 for connection information.
3 COAXIAL jack
See page 15 for connection information.
4 System connector (TO RX-E410) jack
See page 12 for connection information.
English
7 En
Controls and Functions
Remote control
INPUT
This remote control can operate the PianoCraft system
components (including tuner functions) and an iPod
stationed in a YAMAHA iPod universal dock connected to
the receiver.
To operate the CD player, tuner functions, or an iPod
using the remote control, you need to set the receiver to
the corresponding input mode.
VOLUME
DISPLAY
SLEEP
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
Input
selection
keys
To switch the input mode of the receiver
Press the corresponding input selection key on the remote
control (or INPUT on the front panel).
The name of the corresponding input source appears in the
front panel display of the receiver.
y
For a complete list of the remote control functions used to control
your iPod, refer to “Available iPod operations” (see page 35).
■ Common functions
1
2
Operations common to all modes
The following operations are available for the receiver
when it is set to any input mode.
STANDBY/ON
1
2
3
5
6
7
8
DIMMER
9
1 Infrared signal transmitter
Sends signals to the component you want to control.
4
0
6
2 STANDBY/ON (
)
Turns the receiver on or sets it to the standby mode.
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
3 DISPLAY
Switches the information shown in the front panel display
(see page 20).
START
RANDOM
TIME/INFO
FOLDER/PRESET
FILE
/A-E
3
ENTER
INPUT
4 INPUT
/
Selects the input source on the receiver.
MENU
5 SLEEP
Sets the sleep timer on the receiver (see page 33).
FILE
/A-E
VOLUME
DISPLAY
4
7
SLEEP
5
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
8
6 DIMMER
Changes the brightness of the receiver’s front panel
display (see page 20).
7 VOLUME +/–
Adjusts the overall volume level on the receiver.
8 Input selection keys
Select the input source on the receiver.
y
STANDBY/ON, DIMMER and SLEEP operations also control
the CD player by the system control connection (see page 12).
8 En
Controls and Functions
■ CD mode
Operations available in CD mode
STANDBY/ON
1
1
2
3
4
5
6
7
8
9
0
y
Press CD to set the receiver to the CD mode before
carrying out the following operations.
DIMMER
2
3
4
5
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
START
RANDOM
TIME/INFO
FOLDER/PRESET
FILE
/A-E
ENTER
INPUT
6
7
8
9
MENU
FILE
/A-E
VOLUME
DISPLAY
SLEEP
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
0
1 Number keys (1 to 9, 0)
Input numerals to specify track numbers.
INTRODUCTION
The following operations are available for the CD player if
the CD player is connected to the receiver with the system
control connection (see page 12).
2 PROG
Sets the CD player to the track program mode (see
page 25).
3 e
Pauses playback (see page 21).
4 s
Stops playback (see page 21).
5 TIME/INFO
Switches the disc information shown in the CD player’s
front panel display (see page 22).
6 REPEAT
Selects the Repeat Play mode (see page 24).
7 RANDOM
Turns on/off the Random Play feature (see page 24).
8 h
Starts playback (see page 21).
9 b, a
Skips to the beginning of the current track or next track.
Press and hold to fast reverse or fast forward (see
page 21).
0 FOLDER
/
, FILE
/ , ENTER
Press FOLDER
/
to select a folder and FILE
/ to select a file for an MP3 or a WMA disc (see
page 21).
English
9 En
Controls and Functions
■ TUNER mode
Operations available in TUNER mode
The following operations are available for the receiver.
y
Press TUNER to set the receiver to the TUNER mode before
carrying out the following operations.
STANDBY/ON
1
2
3
4
5
6
7
8
9
0
1
DIMMER
1 Number keys (1 to 8)
Selects preset station number (see page 28).
2 Radio Data System tuning keys
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
START
RANDOM
2
TIME/INFO
FOLDER/PRESET
FILE
/A-E
ENTER
INPUT
FREQ/TEXT
Switches the Radio Data System display between the
PS mode, PTY mode, RT mode, CT mode (if the
station offers the corresponding data services) and the
frequency display (see page 30).
MENU
PTY SEEK MODE
Sets the receiver to the PTY SEEK mode (see
page 29).
FILE
/A-E
VOLUME
DISPLAY
3
SLEEP
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
4
PTY SEEK START
Starts searching for a station once the desired
program type is selected in the PTY SEEK mode (see
page 29).
3 A-E
/ , PRESET
/
Press A-E / to select a preset station group (A to E)
and PRESET
/
to select a preset station number
(1 to 8) (see page 28).
4 BAND
Switches the radio reception mode between FM, AM and
the preset mode.
10 En
Controls and Functions
■ Installing the batteries in the remote
control
■ Using the remote control
NATURAL SOUND STEREO RECEIVER RX-E410
PURE DIRECT
DISPLAY
TIMER
MEMORY
AUTO/MAN'L
PRESET/BAND
PRESET/TUNING
VOLUME
TIME ADJ
BASS
STANDBY/ON
TIMER
TREBLE
HOUR
MIN
INPUT
BALANCE
PHONES
Press
Within 6 m
(20 feet)
L
MIN
30˚
1
Press the
mark on the battery cover and
open the cover.
2
Insert the two supplied batteries (AA, R06,
UM-3) into the battery compartment.
Make sure you insert the batteries according to the
polarity markings (+ and –).
3
Close the battery cover.
R
MAX
INTRODUCTION
Use the remote control within 6 m (20 feet) of the
component you want to control and point it toward its
remote control sensor (see page 3).
30˚
Notes
• Be careful not to spill liquid on the remote control.
• Be careful not to drop the remote control.
• Do not leave the remote control in the following places:
– hot or humid places, such as near a heater or in a bathroom
– extremely cold places
– dusty places
Notes
• Do not use an old battery together with new one.
• Do not use different types of batteries (for example, alkaline
and manganese) together. Each type of battery has its own
characteristics even if they are similar in shape.
• If the batteries run out, immediately remove them from the
remote control to prevent an explosion or acid leak.
• Dispose of the batteries according to the regional regulations.
• If a battery starts leaking, dispose of it immediately. Be careful
not to let leaking battery acid come into contact with your skin
or clothing. Before inserting new batteries, wipe the
compartment clean.
English
11 En
CONNECTING THE SYSTEM
Connecting the System
Make sure you read the following procedure and notes carefully before connecting the system. For information on the
speakers (NX-E800), refer to the owner’s manual supplied with it.
Note
Do not connect the power cable of the receiver, CD player, or other components to the wall outlet until all cable connections are
completed.
Right speaker
(NX-E800)
Left speaker
(NX-E800)
3
3
MAINS
ANTENNA
75
UNBAL.
SPEAKERS
6 MIN / SPEAKER
DOCK
FM
CD
AC OUTLETS
SWITCHED
R
L
GND
IN
OUT
TAPE/MD
AM
SUBWOOFER
OUT
TO CDX-E410
AUX
100W MAX. TOTAL
R
L
1
2
Receiver (RX-E410)
(Europe model)
MAINS
LINE OUT
DIGITAL OUT
L
OPTICAL
TO RX-E410
COAXIAL
R
CD player (CDX-E410)
1 Connect the CD (L/R) jacks of the receiver to the LINE OUT (L/R) jacks of the CD player using the supplied audio
pin cable.
2 Connect the system connector (TO CDX-E410) jack of the receiver to the system connector (TO RX-E410) jack of the
CD player using the supplied system control cable.
3 Connect the speaker terminals (L) of the receiver to the speaker terminals of the left speaker and the speaker terminals
(R) of the receiver to the speaker terminals of the right speaker using the speaker cables supplied with the speaker set
(NX-E800). See page 13 for details.
y
• The system control connection is used to transmit the remote control signals from the receiver to the CD player.
• If you want to connect an amplifier with a digital input instead of the RX-E410, use the DIGITAL OUT (COAXIAL or OPTICAL)
jacks of the CD player.
12 En
Connecting the System
■ Connecting the speaker cable
4
Tighten the knob to secure the wire.
Notes
1
Red: positive (+)
Black: negative (–)
PREPARATION
• Be sure to connect the left channel (L), right channel (R), “+”
(red) and “–” (black) properly. If the connections are faulty, no
sound will be heard from the speakers, and if the polarity of the
speaker connections is incorrect, the sound will be unnatural
and lack bass.
• Do not let the bare speaker wires touch each other or do not let
them touch any metal part of the receiver. This could damage
the receiver and/or the speakers.
• When connecting another speaker set instead of the NX-E800,
be sure to use speakers with the specified impedance shown on
the rear panel of the receiver and magnetically shielded. In case
the magnetically shielded speakers interfere with the monitor,
place the speakers away from the monitor.
Remove approximately 10 mm (3/8 in) of
insulation from the end of each speaker
cable and then twist the exposed wires of the
cable together to prevent short circuits.
10 mm (3/8 in)
2
Unscrew the knob.
Red: positive (+)
Black: negative (–)
3
Insert the bare wire into the terminal.
Red: positive (+)
Black: negative (–)
English
13 En
CONNECTING ANTENNAS
Connecting Antennas
To enjoy radio on the receiver, connect the supplied AM and FM antennas to the designated terminals. If there is a
problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use
optional outdoor antennas. For details, consult the nearest authorized YAMAHA dealer or service center.
AM loop
antenna
(supplied)
3
Insert the AM loop antenna lead wires into
the AM terminal.
4
Replace the tab back to secure the wire.
5
Repeat steps 2 to 4 to insert the AM loop
antenna lead wires into the GND terminal.
6
Place the antenna away from the receiver and
speaker cables.
While listening to the radio, rotate the antenna head
to find the best angle for reception.
Indoor FM
antenna
(supplied)
ANTENNA
75
UNBAL.
SPEAKERS
6 MIN / SPEAKER
DOCK
FM
CD
R
L
GND
IN
OUT
TAPE/MD
AM
AUX
R
L
Ground
(GND terminal)
■ About grounding
For maximum safety and minimum interference, connect
the antenna GND terminal to a good earth ground. A good
earth ground is a metal stake driven into moist earth.
Connecting the AM loop antenna
1
Attach the antenna stand to the antenna.
When attaching the antenna to the wall, you do not
need to use the antenna stand.
Connecting the FM antenna
2
1
Connect the supplied indoor FM antenna to
the FM jack of the receiver.
2
Place the antenna away from the receiver and
speaker cables.
Press down the tab of the AM terminal.
Note
Depending on the product, the shape of the tab is different from
the described illust.
14 En
CONNECTING EXTERNAL COMPONENTS
Connecting External Components
You can connect various audio components, such as an MD player, a tape deck or a YAMAHA iPod universal dock to the
receiver. Also you can connect an MD recorder or a CD recorder to the CD player using the DIGITAL OUT jacks. For
information on your external component, refer to the owner’s manual supplied with each component.
Note
Do not connect the power cable of the receiver, CD player, or other components to the wall outlet until all cable connections are
completed.
Connecting an MD recorder or a CD
recorder
If you connect an MD player or a tape deck to the receiver,
you can enjoy audio sources played on the component.
If you connect an MD recorder or a CD recorder to the CD
player with a digital connection, you can make a digital
recording.
PREPARATION
Connecting an MD player or a tape
deck
ANALOG
IN
OUT
L
OPTICAL
R
COAXIAL
or
MD player or
tape deck
MD recorder or
CD recorder
Audio pin cable
Optical cable
Coaxial cable
ANTENNA
75
UNBAL.
DOCK
FM
CD
GND
IN
OUT
TAPE/MD
AM
AUX
R
LINE OUT
L
Receiver
DIGITAL OUT
L
OPTICAL
TO RX-E410
COAXIAL
R
1
2
Connect the TAPE/MD IN (L/R) jacks of the
receiver to the analog output jacks of an MD
player or a tape deck using a commercially
available audio pin cable.
To record audio output from the receiver,
connect the TAPE/MD OUT (L/R) jacks of the
receiver to the analog input jacks of an MD
player or a tape deck using a commercially
available audio pin cable.
CD player
Connect the DIGITAL OUT (COAXIAL or
OPTICAL) jack of the CD player to the digital
input (coaxial or optical) jack of an MD recorder
or a CD recorder using a commercially available
coaxial or optical cable.
Notes
• The DIGITAL OUT jacks are compatible with PCM signals.
• The DIGITAL OUT (OPTICAL) jack is designed based on EIA
standards. To make a digital connection, use an optical cable
that meets EIA standards.
English
15 En
Connecting External Components
Connecting a YAMAHA iPod universal dock
The receiver (RX-E410) is equipped with the DOCK terminal on the rear panel that allows you to connect a YAMAHA
iPod universal dock (such as YDS-10 sold separately) where you can station your iPod and control playback of your iPod
using the supplied remote control. Connect a YAMAHA iPod universal dock (such as YDS-10 sold separately) to the
DOCK terminal on the rear of the receiver using its dedicated cables. Once the connection is complete, station your iPod
in the YAMAHA iPod universal dock.
iPod
YAMAHA iPod universal dock
(such as YDS-10 sold separately)
MAINS
ANTENNA
75
UNBAL.
DOCK
SPEAKERS
6 MIN / SPEAKER
FM
CD
AC OUTLETS
SWITCHED
R
L
GND
IN
OUT
TAPE/MD
AM
SUBWOOFER
OUT
100W MAX. TOTAL
AUX
R
TO CDX-E410
L
Receiver (Europe model)
Notes
• Do not connect the power cable of the receiver, CD player, or other components to the wall outlet until all cable connections are
completed.
• Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.
• You need a YAMAHA iPod universal dock (such as YDS-10 sold separately) and its dedicated cable compatible with the DOCK
terminal of the receiver.
• Do not connect any iPod accessories (such as headphones, a wired remote control, or an FM transmitter) to your iPod when it is
stationed in a YAMAHA iPod universal dock (such as YDS-10 sold separately).
• Unless your iPod is firmly stationed in a YAMAHA iPod universal dock (such as YDS-10 sold separately) connected to the DOCK
terminal of the receiver, audio signals may not be output properly.
• Once the connection between your iPod and the receiver is complete and the receiver is set to DOCK mode (see page 8), “iPod
connected” appears in the front panel display. If the connection between your iPod and the receiver fails, a status message appears in
the front panel display. For a complete list of connection status message, see the iPod section in “Troubleshooting” on page 38.
• Your iPod battery is automatically charged when your iPod is stationed in a YAMAHA iPod universal dock (such as YDS-10 sold
separately) connected to the DOCK terminal of the receiver as long as the receiver is turned on.
• Depending on the type of the iPod, you may need to insert one of the iPod adapters supplied with a YAMAHA iPod universal dock
(such as YDS-10 sold separately) into the dock slot before you station your iPod.
16 En
CONNECTING THE POWER CABLES
Connecting the Power Cables
Once all connections are complete, connect the power cable of the CD player to the AC OUTLET(S) terminal on the rear
of the receiver (or the AC wall outlet if the AC OUTLET(S) terminal is not available), and then plug the power cable of
the receiver into the AC wall outlet.
MAINS
ANTENNA
75
UNBAL.
SPEAKERS
To the AC wall outlet
6 MIN / SPEAKER
DOCK
FM
CD
R
PREPARATION
AC OUTLETS
SWITCHED
L
GND
IN
OUT
TAPE/MD
AM
SUBWOOFER
OUT
TO CDX-E410
100W MAX. TOTAL
AUX
R
Receiver
(Europe model)
L
MAINS
LINE OUT
DIGITAL OUT
L
OPTICAL
To AC OUTLET(S) on the
rear panel of the receiver
(or the AC wall outlet )
TO RX-E410
COAXIAL
R
CD player
■ AC OUTLET(S) (SWITCHED)
U.K. model............................................................. 1 outlet
Other models......................................................... 2 outlets
Use these outlet(s) to supply power to the CD player or any connected components. Connect the power cable of your
other components to these outlet(s). Power to these outlet(s) is supplied when the receiver is turned on. For information
on the maximum power or the total power consumption of the components that can be connected to these outlet(s), see
“Specifications” on page 44.
English
17 En
ADJUSTING THE CLOCK
Adjusting the Clock
Before starting playback operation, follow the procedure below to adjust the clock setting of the receiver.
5
HOUR MIN
DISPLAY
NATURAL SOUND STEREO RECEIVER RX-E410
PURE DIRECT
TIMER
DISPLAY
STANDBY/ON
BASS
MEMORY
AUTO/MAN'L
PRESET/BAND
To set the minute setting ahead, press MIN
repeatedly. To set the minute setting
backward, press MIN repeatedly while
holding down PRESET/BAND.
PRESET/TUNING
VOLUME
TIME ADJ
TIMER
TREBLE
HOUR
MIN
INPUT
BALANCE
PHONES
L
R
MIN
MAX
Flashes
STANDBY/ON TIME ADJ PRESET/BAND
6
1
Press STANDBY/ON on the front panel of the
receiver to turn on it.
The front panel display lights up.
2
Press DISPLAY.
“Clock Time” appears in the front panel display for a
few seconds, and then “Set Clock” appears.
Press TIME ADJ once again to confirm the
clock setting.
“Adjusted” appears in the front panel display for a
few seconds, and then the clock appears.
y
You can switch between 12-hour (AM/PM) format and 24-hour
format by pressing HOUR or MIN while the clock is displayed in
the front panel display.
3
Press TIME ADJ for about two seconds to
enter the clock setting mode.
4
To set the hour setting ahead, press HOUR
repeatedly. To set the hour setting backward,
press HOUR repeatedly while holding down
PRESET/BAND.
Flashes
18 En
Basic Receiver Operations
Basic Receiver Operations
Follow the procedure below to select an input source and adjust the sound settings on the receiver.
3
Start playback on the selected source
component or select a broadcast station.
For information on the disc playback, see page 21, and
for information on tuning, see page 26.
4
Press VOLUME +/– to adjust the volume to
the desired output level.
5
Rotate BASS, TREBLE, or BALANCE on the
front panel of the receiver to adjust the
following settings.
BALANCE PURE DIRECT
PHONES
NATURAL SOUND STEREO RECEIVER RX-E410
PURE DIRECT
DISPLAY
TIMER
MEMORY
AUTO/MAN'L
TIME ADJ
TIMER
PRESET/BAND
PRESET/TUNING
VOLUME
BASS
STANDBY/ON
TREBLE
MIN
HOUR
INPUT
BALANCE
PHONES
L
R
MIN
BASS
MAX
TREBLE
STANDBY/ON
STANDBY/ON
(
)
1
2
3
4
5
FILE
/A-E
6
7
8
FILE
/A-E
ENTER
INPUT
■ Pure Direct mode
The Pure Direct mode shuts down the tone control
circuitry, allowing you to enjoy pure high-fidelity sounds
from analog sources.
VOLUME
BASIC
OPERATIONS
BASS: Adjusts the low frequency response.
TREBLE: Adjusts the high frequency response.
BALANCE: Adjusts the volume level of each left
and right speaker channel.
DISPLAY
INPUT
VOLUME +/–
/
SLEEP
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
Input
selection
keys
Press PURE DIRECT on the front panel of the
receiver to turn on the Pure Direct mode.
PURE DIRECT lights up, and the front panel display
automatically dims.
Notes
• While the Pure Direct mode is turned on, neither BASS,
TREBLE, nor BALANCE are available.
• If you carry out any operation while the Pure Direct mode is
turned on, the front panel display lights up briefly to
acknowledge the command and dims again.
1
Press STANDBY/ON to turn on the receiver.
The CD player also turns on by the system control
connection (see page 12). The front panel display
lights up.
y
This system has the auto-standby function (see page 34) which
automatically set to the system to the standby mode if you do not
operate the system for 30 minutes while the receiver is set to the
CD input mode.
2
To turn off the Pure Direct mode
Press PURE DIRECT again so that PURE DIRECT turns
off and the front panel display lights up.
■ To use headphones
Connect the headphones to the PHONES jack. You can
listen to the sound to be output from the speakers through
the headphones.
Press one of the input selection keys or
INPUT
/
to select the desired input
source.
English
19 En
Basic Receiver Operations
Changing the front panel display settings
Follow the procedure below to change the settings of the receiver’s front panel display.
■ To switch the display mode
You can switch the information displayed in the receiver’s
front panel display between the current input and clock.
STANDBY/ON
1
2
3
5
6
7
4
Note
8
DIMMER
9
DIMMER
0
You cannot display the clock unless you adjust it (see page 18).
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
Press DISPLAY repeatedly to select the desired
display mode.
Each time you press the key, the display changes as
follows.
START
RANDOM
TIME/INFO
FOLDER/PRESET
MENU
(Current input)
FILE
/A-E
ENTER
INPUT
FILE
/A-E
Clock Time
Timer Input
VOLUME
DISPLAY
DISPLAY
ON Time
SLEEP
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
OFF Time
y
“Timer Input”, “ON Time”, and “OFF Time” are used to set the
clock timer (see page 32).
■ To dim the display
You can dim the front panel display of the receiver. The
front panel display of the CD player also dims by the
system control connection (see page 12). (The default
setting is “DIMMER OFF”.)
Press DIMMER to select “DIMMER ON”.
To return to normal brightness
Press DIMMER to select “DIMMER OFF”.
20 En
Basic Disc Playback Operations
Basic Disc Playback Operations
You can enjoy playback of audio CDs, MP3 CDs, and WMA CDs with the CD player. However, depending on a disc
format, some discs may not be compatible with the CD player. Before loading a disc into the CD player, be sure to check
the disc compatibility of the CD player (see page 42).
To skip tracks
Note
Depending on the disc, some operations may be different or
restricted.
To skip to the start of the current track, press b.
To skip to the next track, press a.
To skip to the previous track, quickly press b twice.
To specify a track for playback
STANDBY/ON
Number
keys
1
2
3
4
5
6
7
8
9
0
b, a
Note
h
The track number for an MP3, or WMA disc is recognized per a
disc, not per folder. The number assigned to each track
corresponds to sequence of a disc.
DIMMER
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
e
START
RANDOM
TIME/INFO
FOLDER/PRESET
FILE
/A-E
ENTER
MENU
FILE
/A-E
FOLDER
FILE
INPUT
/
/
,
, ENTER
To select a folder/file for an MP3 or WMA
disc
BASIC
OPERATIONS
s
Use the number keys to enter the track number you want
to play.
Example: To select the track number 8, press 8, and then
wait a few seconds so that 8 is confirmed, or press 0, and
then 8.
VOLUME
To start playback
To select a folder, press FOLDER
/
.
To select a file, press FILE / .
To start playback of the selected folder/file, press ENTER.
Press h while a disc is loaded.
■ About MP3 and WMA discs
DISPLAY
y
When you open the disc tray by pressing
on the front panel of
the CD player, you can also close the disc tray by pressing h, a
Root
numeric key, or RANDOM other than . In this case, disc
playback starts automatically after the disc tray is closed.
Folder
File (Track)
To stop playback
Press s.
To pause playback
Press e.
To return to normal playback, press h.
You can play back MP3 and WMA format files recorded
on a CD-R/RW with similar uses as a music CD. The CD
player regards files in the disc as tracks (as shown above).
Note
To fast reverse or fast forward
To fast reverse, hold down b.
To fast forward, hold down a.
Depending on recording conditions such as recording software
settings, the CD player may not be able to play the disc at all, or
may not play tracks in the order they were recorded. For
information on disc compatibility of the CD player, see page 42.
English
21 En
Basic Disc Playback Operations
Switching the playback information display
You can switch the disc playback information shown in the CD player’s front panel display. Available information differs
depending on a disc type.
Press TIME/INFO repeatedly while playing back a
disc.
Each time you press the key, the information display
STANDBY/ON
changes as described in “Playback information for audio
CDs” and “Playback information for MP3 and WMA
discs”.
1
2
3
5
6
7
9
0
4
8
Notes
DIMMER
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
• Some information may not be available depending on a disc.
• Some special characters may not be shown properly.
START
RANDOM
TIME/INFO
TIME/INFO
FOLDER/PRESET
MENU
■ Playback information for audio CDs
The following information is available during playback of an audio CD. “Disc title”, “Artist name”, and “Track name”
are available only for a CD TEXT disc.
1 Elapsed time of the current track (Default)
CD
7 Disc title
CD
2 Remaining time of the current track
CD
6 Artist name
CD
3 Total time of the disc
CD
4 Remaining time of the disc
CD
22 En
5 Track name
CD
Basic Disc Playback Operations
■ Playback information for MP3 and WMA discs
The following information is available during playback of an MP3 or WMA disc.
1 Scrolling display (Default)
9 Comment
MP3
MP3
8 Year
2 Elapsed time of the current file
MP3
MP3
7 Album name
3 Remaining time of the current file
MP3
MP3
4 File name
6 Artist name
MP3
MP3
5 Song title
BASIC
OPERATIONS
MP3
y
Scrolling display shows the song title, artist name, and album name of the selected item in sequence.
English
23 En
Basic Disc Playback Operations
Repeating playback
(Repeat Play)
Playing back randomly
(Random Play)
You can repeat the playback of the selected item in a disc.
You can play back tracks in the disc in random order.
Note
When playing back an audio CD with Random Play, the
remaining time of the disc cannot be displayed.
STANDBY/ON
1
2
3
4
5
6
7
8
9
0
STANDBY/ON
DIMMER
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
REPEAT
1
2
3
4
5
6
7
8
9
0
START
DIMMER
1
2
Play back the disc or track you want to
repeat.
Press REPEAT to select the desired Repeat
Play mode.
Each time you press the key, the Repeat Play mode
indicator in the CD player’s front panel display
changes as follows.
Audio CD
↓
Off (Normal playback)
↓
(Repeat Play by track)
↓
ALL
(Repeat Play by disc)
MP3/WMA disc
↓
Off (Normal playback)
↓
(Repeat Play by file)
↓
flashes (Repeat Play by folder)
ALL
↓
(Repeat Play by disc)
To cancel Repeat Play
Press REPEAT repeatedly so that the Repeat Play mode
indicator disappears from the front panel display.
24 En
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
START
RANDOM
RANDOM
While the disc is loaded into the CD player, press
RANDOM.
The RANDOM indicator lights up in the CD player’s front
panel display and Random Play starts.
To cancel Random Play
Press RANDOM so that the RANDOM indicator
disappears from the front panel display.
Basic Disc Playback Operations
Customizing playback order
(Program Play)
In case of MP3 or WMA disc
PROG.
You can customize the playback order for 40 tracks stored
in the disc.
Note
The total number of programmed tracks and the total time of
programmed tracks are not displayed for MP3 or WMA disc.
STANDBY/ON
y
Number
keys
1
2
3
4
5
6
7
8
9
0
The track number for an MP3 or WMA disc is recognized per
disc, not per folder. The number assigned to each track
corresponds to sequence of a disc.
DIMMER
FREQ/TEXT
PROG
PROG
REPEAT
MODE
PTY SEEK
START
s
Repeat step 2 until you program all desired
tracks.
4
To finish programming tracks, press PROG.
The program display disappears and the playback
information of the first programmed track appears in
the front panel display.
5
To start Program Play, press h.
b, a
h
TIME/INFO
FOLDER/PRESET
1
MENU
While the disc is loaded into the CD player,
press PROG.
The PROG indicator lights up and the program
display appears in the CD player’s front panel
display.
PROG.
■ To clear the program order
BASIC
OPERATIONS
3
RANDOM
While the playback is stopped, press s.
Note
If you open the disc tray or set the CD player to the standby
mode, the programmed order is automatically cleared.
Program number
2
Track number
Use the number keys to enter the track
number you want to program.
Example: To select the track number 8, press 8, and
then wait a few seconds so that 8 is confirmed, or
press 0, and then 8.
The front panel display shows the total number and
total time of the programmed tracks for a few
seconds, and then returns to the program display.
Total number of
programmed tracks
Total time of
programmed tracks
■ To check or correct the programmed
tracks
1
While the playback is stopped, press PROG.
The program display appears in the CD player’s front
panel display.
2
Press b or a to check the program
order.
3
To replace a programmed track with new one,
display the program number to be corrected
in step 2, and then use the number keys to
enter the track number to be programmed.
4
To finish checking or correcting the
programmed tracks, press PROG.
PROG.
PROG.
English
25 En
FM/AM Tuning
FM/AM Tuning
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and
there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use
the automatic and manual preset tuning features to store up to 40 stations (A1 to E8: 8 preset station numbers in each of
the 5 preset station groups).
Automatic tuning
Manual tuning
Automatic tuning is effective when station signals are
strong and there is no interference.
If the signal received from the station you want to select is
weak, tune into it manually.
AUTO/MAN’L PRESET/TUNING u / d
AUTO/MAN’L PRESET/TUNING u / d
NATURAL SOUND STEREO RECEIVER RX-E410
NATURAL SOUND STEREO RECEIVER RX-E410
PURE DIRECT
TIMER
DISPLAY
STANDBY/ON
BASS
MEMORY
AUTO/MAN'L
PRESET/BAND
PURE DIRECT
PRESET/TUNING
VOLUME
TIME ADJ
TIMER
TREBLE
HOUR
DISPLAY
BASS
MEMORY
AUTO/MAN'L
PRESET/BAND
PRESET/TUNING
VOLUME
TIME ADJ
PHONES
TIMER
TREBLE
HOUR
MIN
INPUT
BALANCE
PHONES
L
R
L
MIN
PRESET/BAND
R
MAX
MIN
PRESET/BAND
INPUT
1
Rotate INPUT on the front panel of the receiver
to select “TUNER” as an input source.
2
Press PRESET/BAND repeatedly to select
“FM” or “AM”.
When the preset indicator lights up, the receiver is in the
preset mode. For details, see pages 27 and 28.
3
Press AUTO/MAN’L so that the AUTO
indicator lights up in the front panel display.
4
Press PRESET/TUNING u / d to begin
automatic tuning.
When the reciever is tuned into a station, the TUNED
indicator lights up and the frequency of the received
station is shown in the front panel display.
• Press u to tune into a higher frequency.
• Press d to tune into a lower frequency.
MAX
INPUT
1
Rotate INPUT on the front panel of the receiver
to select “TUNER” as an input source.
2
Press PRESET/BAND to select “FM” or “AM”.
y
When the preset indicator lights up, the receiver is in the
preset mode. For details, see pages 27 and 28.
y
26 En
TIMER
STANDBY/ON
MIN
INPUT
BALANCE
3
Press AUTO/MAN’L so that the AUTO
indicator disappears from the front panel
display.
4
Press PRESET/TUNING u / d to tune into
the desired station manually.
Hold down the button to continue searching.
FM/AM Tuning
Automatic preset tuning
Manual preset tuning
Follow the procedure below to preset radio stations
automatically.
You can also store up to 40 stations (A1 to E8: 8 preset
station numbers in each of the 5 preset station groups)
manually.
NATURAL SOUND STEREO RECEIVER RX-E410
PURE DIRECT
NATURAL SOUND STEREO RECEIVER RX-E410
TIMER
DISPLAY
STANDBY/ON
BASS
MEMORY
AUTO/MAN'L
PRESET/BAND
PURE DIRECT
PRESET/TUNING
VOLUME
TIME ADJ
TIMER
TREBLE
HOUR
MIN
INPUT
BALANCE
PHONES
TIMER
DISPLAY
STANDBY/ON
BASS
MEMORY
R
AUTO/MAN'L
PRESET/BAND
PRESET/TUNING
VOLUME
TIME ADJ
L
TIMER
TREBLE
HOUR
MIN
INPUT
BALANCE
PHONES
MIN
MAX
L
R
MIN
MAX
MEMORY INPUT
MEMORY
1
2
Rotate INPUT on the front panel of the receiver
to select “TUNER” as an input source.
1
Tune into a radio station you want to preset.
See page 26 for tuning instructions.
2
Press MEMORY.
The MEMORY indicator flashes in the front panel
display for about 5 seconds.
3
Hold down PRESET/TUNING u / d to select
a preset station group (A to E) while the
MEMORY indicator is flashing.
4
Press PRESET/TUNING u / d repeatedly to
select a preset station number (1 to 8) while
the MEMORY indicator is flashing.
5
Press MEMORY while the MEMORY indicator
is flashing.
The PRESET and MEMORY indicators light up in
the front panel display.
6
Repeat steps 1 to 5 until all desired stations
are preset.
Note
You can preset up to 40 of AM and FM stations with Auto Preset.
TUNER
OPERATIONS
Hold down MEMORY for more than two
seconds.
The AUTO and MEMORY indicator flash in the front
panel display.
• Auto Preset starts at the lowest frequency toward
the highest frequency.
• The receiver automatically applies a preset number
to each detected station.
PRESET/TUNING u / d
English
27 En
FM/AM Tuning
Selecting preset stations
You can tune into any desired station simply by selecting
the preset station group and number under which it was
stored (see page 27).
PRESET/TUNING u / d
NATURAL SOUND STEREO RECEIVER RX-E410
PURE DIRECT
DISPLAY
TIMER
MEMORY
AUTO/MAN'L
PRESET/BAND
PRESET/TUNING
VOLUME
TIME ADJ
BASS
STANDBY/ON
TIMER
TREBLE
HOUR
MIN
INPUT
BALANCE
PHONES
L
R
MIN
MAX
PRESET/BAND INPUT
1
Rotate INPUT on the front panel of the receiver
to select “TUNER” as an input source.
2
Press PRESET/BAND repeatedly so that the
preset indicator lights up in the front panel
display.
3
Hold down PRESET/TUNING u / d to select
a preset station group (A to E), and then
press PRESET/TUNING u / d repeatedly to
select a preset station number (1 to 8).
y
You can also use the remote control to select preset stations.
While the receiver is set to the TUNER mode (see page 8), press
BAND repeatedly to select “PRESET”. To select a preset station
group (A to E), press A-E
/
repeatedly. To select a preset
station number (1 to 8), press PRESET
use the number keys (1 to 8).
28 En
/
repeatedly or
Radio Data System Tuning (U.K. and Europe Models Only)
Radio Data System (U.K. and Europe models only) is a data transmission system used by FM stations in many countries.
The Radio Data System function is carried out among the network stations. This unit can receive various Radio Data
System data such as PS (program service), PTY (program type), RT (radio text), CT (clock time), and EON (enhanced
other networks) when receiving Radio Data System broadcasting stations.
Selecting the Radio Data System
program
Use this feature to select one of the 15 Radio Data System
program types and search for all the available preset
stations of the selected program type.
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
PTY SEEK
MODE
PTY SEEK
START
TIME/INFO
FILE
/A-E
ENTER
MENU
FILE
/A-E
PRESET
/
INPUT
Descriptions
NEWS
News
AFFAIRS
Current affairs
INFO
General information
SPORT
Sports
EDUCATE
Education
DRAMA
Drama
CULTURE
Culture
CD
TUNER
BAND
SCIENCE
Science
TAPE/MD
AUX/TV
DOCK
TUNER
VARIED
Light entertainment
POP M
Popular music
ROCK M
Rock music
M.O.R. M
Middle-of-the-road music (easylistening)
Set the receiver to the “FM” tuning mode.
See page 26 for tuning instructions.
LIGHT M
Light classics
CLASSICS
Serious classics
OTHER M
Other music
TUNER
OPERATIONS
SLEEP
2
Program type
VOLUME
DISPLAY
1
Press PRESET
/
repeatedly to select
the desired program type.
The name of the selected program type appears in the
front panel display.
START
RANDOM
FOLDER/PRESET
3
Press PTY SEEK MODE to set the receiver to
the PTY SEEK mode.
The PTY indicator and the name of the program type
flash in the front panel display of the receiver.
y
• To cancel the PTY SEEK mode, press PTY SEEK MODE
once again.
• The PTY SEEK mode is automatically cancelled if you do
not operate any key for about 20 seconds.
English
29 En
Radio Data System Tuning (U.K. and Europe Models Only)
4
Press PTY SEEK START to start searching
for available Radio Data System preset
stations.
If a station broadcasting the selected program type is
found, the receiver stops searching, and then program
service name and the PTY HOLD indicator lights up
in the front panel display.
If there is no station broadcasting the selected
program type, the frequency currently selected
appears.
y
DIMMER
9
0
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
FREQ/TEXT
START
RANDOM
TIME/INFO
FOLDER/PRESET
FILE
/A-E
ENTER
INPUT
To stop searching for stations, press PTY SEEK START
once again.
MENU
FILE
/A-E
VOLUME
DISPLAY
SLEEP
5
Repeat step 4 until the desired station is
found.
Displaying the Radio Data System
information
Use this feature to display the 4 types of the Radio Data
System information: PS (program service), PTY (program
type), RT (radio text) and CT (clock time). The
corresponding indicators light up in the front panel
display.
Notes
• You can select one of the Radio Data System modes only when
the corresponding Radio Data System indicator lights up in the
front panel display. It may take a while for the receiver to
receive all of the Radio Data System data from the station.
• You can select only the available Radio Data System modes
being offered by the station.
• If the signals being received are not strong enough, the receiver
may not be able to utilize the Radio Data System data. In
particular, the “RT” mode requires a large amount of data and
may not be available even when the other Radio Data System
modes are available.
• In case of poor reception conditions, press AUTO/MAN’L on
the front panel of the receiver so that the AUTO indicator
disappears from the front panel display.
• If the signal strength is weakened by external interference while
the receiver is receiving the Radio Data System data, the
reception may be cut off unexpectedly and “...WAIT” appears in
the front panel display.
• When the “RT” mode is selected, the receiver can display the
program information by a maximum of 64 alphanumeric
characters, including the umlaut symbol. Unavailable characters
are displayed with the “_” (underscore).
30 En
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
TUNER
While tuning into a Radio Data System station,
press FREQ/TEXT repeatedly to select the
desired Radio Data System display mode.
PS
PTY
RT
CT
Frequency
• Select “PS” to display the name of the Radio Data
System program currently being received.
• Select “PTY” to display the type of the Radio Data
System program currently being received.
• Select “RT” to display the information on the
Radio Data System program currently being
received.
• Select “CT” to display the current time.
Radio Data System Tuning (U.K. and Europe Models Only)
■ Additional CT (clock time) settings
You can use CT information received from the Radio Data
System stations to adjust the built-in clock of the receiver.
3
Press PTY SEEK MODE repeatedly to select
“CT→Clock” or “Local CT”, and then press
PTY SEEK START to switch the setting
between “ON” and “OFF”.
STANDBY/ON
1
2
3
5
6
7
CT→Clock
Set this to “ON” if you want to apply CT information
received from the Radio Data System stations to the
built-in clock of the receiver. (The default setting is
“ON”.)
4
8
DIMMER
9
0
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
FREQ/TEXT
Local CT
Set this to “ON” if you want to apply the daylight
saving time or summer time to CT information
received from the Radio Data System stations. (The
default setting is “ON”.)
START
RANDOM
PTY SEEK START
PTY SEEK MODE
TIME/INFO
FOLDER/PRESET
FILE
/A-E
ENTER
INPUT
MENU
4
FILE
/A-E
Press FREQ/TEXT to confirm the settings.
VOLUME
DISPLAY
DISPLAY
SLEEP
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
TUNER
While tuning into a Radio Data System
station, press DISPLAY repeatedly so that the
clock appears in the front panel display of
the receiver.
2
Press FREQ/TEXT once.
“CT→Clock” appears in the front panel display.
TUNER
OPERATIONS
1
English
31 En
SETTING THE TIMER
Setting the Timer
The receiver is equipped with 2 types of timer functions: clock timer and sleep timer. The clock timer automatically turns
the receiver on or sets it to the standby mode at the specified time. The sleep timer sets the receiver to the standby mode
after the specified time elapses. The CD player also turns on or sets to the standby mode automatically by the system
control connection (see page 12).
Setting the clock timer
The clock timer automatically turns the receiver on or sets
it to the standby mode at the specified time. You can also
specify an input which the receiver automatically selects
when the clock timer turns it on.
Notes
• You cannot set the clock timer unless you adjust the clock (see
page 18).
• If you do not touch any key for more than 30 seconds after the
previous key operation, the operations you made are cleared
from the memory and the normal display reappears.
TIMER indicator
TIMER
PRESET/BAND
PURE DIRECT
TIMER
DISPLAY
BASS
MEMORY
AUTO/MAN'L
PRESET/BAND
PRESET/TUNING
VOLUME
TIME ADJ
TIMER
TREBLE
HOUR
MIN
INPUT
BALANCE
PHONES
L
R
MIN
DISPLAY
MAX
INPUT
1
Press DISPLAY on the front panel of the
receiver repeatedly to select “Timer Input”.
The TIMER indicator flashes in the front panel
display.
2
Rotate INPUT to select an input which the
receiver automatically selects when the clock
timer turns it on.
If you select “TUNER”, you can select a band by
pressing PRESET/BAND. To select a preset station,
carry out steps 2 and 3 in the “Selecting preset
stations” procedure (see page 28).
3
Press DISPLAY again to select “ON Time”.
4
Specify the time when you want to turn on
the receiver.
Carry out the steps 4 and 5 in “Adjusting the Clock”
(see page 18) to adjust the hour and minute settings.
32 En
Press DISPLAY again to select “OFF Time”,
and then specify the time when you want to
turn off the receiver as well as step 4.
6
To turn off the receiver now with the clock
timer set, press TIMER.
The TIMER indicator lights up. The receiver will be
turned on or set to the standby mode automatically at
the specified time.
y
If you want to turn off the receiver by “OFF Time”, press
DISPLAY repeatedly to display the clock in the front panel
display, and then press TIMER. The TIMER indicator lights
up in the front panel display.
To set or cancel the clock timer
Press TIMER on the front panel while the clock is
displayed or the receiver is in the standby mode.
NATURAL SOUND STEREO RECEIVER RX-E410
STANDBY/ON
5
Setting the Timer
Setting the sleep timer
The sleep timer sets the receiver to the standby mode after
the specified time elapses.
FOLDER/PRESET
FILE
/A-E
ENTER
INPUT
MENU
FILE
/A-E
VOLUME
DISPLAY
SLEEP
SLEEP
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
Press SLEEP repeatedly to select the desired
duration.
Each time you press the key, the duration changes as
follows.
The SLEEP indicator lights up in the front panel display.
SLEEP 120 min.
SLEEP 90 min.
SLEEP 60 min.
SLEEP 30 min.
OTHER
OPERATIONS
SLEEP OFF
y
• The sleep timer is canceled if you set the receiver to the standby
mode.
• If you press SLEEP once while the sleep timer is set, the
ongoing duration appears in the front panel display.
To cancel the sleep timer
Press SLEEP repeatedly to select “SLEEP OFF”.
English
33 En
SETTING THE AUTO-STANDBY MODE
Setting the auto-standby mode
You can turn on/off the auto-standby feature which automatically set the system to the standby mode if you do not
operate the system for 30 minutes while the receiver is set to the CD input mode. (The default setting is “AUTO
STANDBY ON”.)
Notes
• Unless you connect the receiver and the CD player with the supplied system control cable properly (see page 12), this feature does not
function for the system.
• This feature does not function for the system during playback.
u/d
NATURAL SOUND STEREO RECEIVER RX-E410
PURE DIRECT
DISPLAY
TIMER
MEMORY
AUTO/MAN'L
PRESET/BAND
PRESET/TUNING
VOLUME
TIME ADJ
BASS
STANDBY/ON
TIMER
TREBLE
HOUR
MIN
INPUT
BALANCE
PHONES
L
R
MIN
MEMORY
MAX
INPUT
1
Rotate INPUT on the front panel of the
receiver to select “CD” as an input source.
2
Press MEMORY.
The current setting appears in the receiver’s front
panel display for about five seconds.
3
While the current setting is displayed in the
front panel display, press u or d to switch
between “AUTO STANDBY ON” or “AUTO
STANDBY OFF”.
4
Press MEMORY or wait for five seconds
without any operation to confirm the setting.
34 En
Controlling iPod
In addition to controlling the receiver (RX-E410) and CD player (CDX-E410), you can operate your iPod stationed in a
YAMAHA iPod universal dock connected to the receiver using the supplied remote control.
Available iPod operations
Operations available in DOCK mode
The following operations are available for the iPod
connected with a YAMAHA iPod universal dock (such as
YDS-10 sold separately). For details on iPod operations,
see “Using iPod” on page 36.
STANDBY/ON
1
2
3
4
5
6
7
8
9
0
y
DIMMER
FREQ/TEXT
1
2
PROG
REPEAT
MODE
PTY SEEK
START
RANDOM
3
4
5
6
7
8
TIME/INFO
FOLDER/PRESET
FILE
/A-E
ENTER
INPUT
MENU
9
Press DOCK to set the receiver to the DOCK mode before
carrying out the following operations.
1 s
Stops playback.
2 e
Pauses playback.
3 b
Skips to the previous track. Press and hold to fast reverse.
FILE
/A-E
VOLUME
DISPLAY
0
4 TIME/INFO
Switches between the simple remote mode and menu
browse mode.
SLEEP
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
5 REPEAT
Selects the repeat playback mode during playback in the
menu browse mode.
6 RANDOM
Selects the shuffle playback mode during playback in the
menu browse mode.
8 a
Skips to the next track. Press and hold to fast forward.
9 MENU
Returns to the upper level in the iPod menu.
OTHER
OPERATIONS
7 h
Starts playback.
0 Cusor keys (
/
/
/ ), ENTER
Press to return to the upper level in the iPod menu.
Press
or
to select an item in the selected group.
Press
or ENTER to enter the selected group. (Pressing
ENTER starts playback when a song is selected.)
English
35 En
Controlling iPod
Using iPod
Once you have stationed your iPod in a YAMAHA iPod universal dock (such as YDS-10 sold separately) connected to
the DOCK terminal of the receiver (see page 16), you can enjoy playback of your iPod using the supplied remote control.
The operations of your iPod are available with the aid of the receiver’s front panel display (menu browse mode) or
without it (simple remote mode).
Notes
• Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.
• Some features may not be compatible depending on the model or the software version of your iPod.
y
• For a complete list of the remote control functions used to control your iPod, refer to “Available iPod operations” (see page 35).
• For a complete list of status messages that appear in the front panel display, refer to the “iPod” section in “Troubleshooting” (see
page 40).
1
Press DOCK to select the iPod as the input
source.
2
Press TIME/INFO to switch between the
simple remote mode and menu browse
mode.
STANDBY/ON
1
2
3
4
5
6
7
8
9
0
DIMMER
FREQ/TEXT
PROG
REPEAT
MODE
PTY SEEK
Simple remote mode
• View the screen of the iPod to control the menu.
• Operate the iPod using the iPod controls or the
supplied remote control.
Menu browse mode
• View the front panel of the receiver to control the
menu.
• Operate the iPod using the supplied remote control.
• You can configure the “Setup” parameters of the
iPod.
START
RANDOM
h
TIME/INFO
TIME/INFO
FOLDER/PRESET
FILE
/A-E
ENTER
INPUT
MENU
FILE
/A-E
VOLUME
DISPLAY
Cursor keys,
ENTER
SLEEP
CD
TUNER
BAND
TAPE/MD
AUX/TV
DOCK
3
DOCK
Use the cursor keys to operate the iPod
menu, and then press ENTER to start
playback of the selected song (or group).
For details on how to operate the iPod menu with the
menu browse mode, refer to “Menu browse mode”
(see page 37).
y
In the simple remote mode, you can also use the iPod controllers
to operate the menu.
36 En
Controlling iPod
■ Menu browse mode
In the menu browse mode, you can operate the iPod menu
using the receiver’s front panel display. Also you can
configure the “Setup” parameters with the menu browse
mode.
2
Note
Press
or
to select the menu, and then
press
or ENTER to enter the selected
menu.
The name of the first item stored in the selected menu
appears.
There are some characters that cannot be displayed in the front
panel display of the receiver. Those characters are replaced with
underscore “_”.
DOCK
iPod menu
DOCK
ARTISTS
y
• The iPod menu indicators (see page 5) show the iPod menu
currently selected.
• To return to the upper level in the iPod menu, press
MENU.
1
Select the menu browse mode (see page 36).
The top of the iPod menu appears in the front panel
display.
3
DOCK
iPod operation indicators
y
The iPod operation indicators (see page 5) show the operable
cursor keys in each step.
or
Repeat step 2 until you select the desired
item, and then press h to start playback of
the desired item (group or song).
If you select “Setup” in step 2, press
or
to select the desired setup menu, and
then press ENTER repeatedly to configure
the parameter.
Setup menu
y
OTHER
OPERATIONS
Shuffle: Off, Songs (Shuffle Play by song), Albums
(Shuffle Play by album)
Repeat: Off, One (Repeat Play by song), ALL (Repeat
Play by selected group)
FL Scroll: Cont (Scrolls the song name continuously,
default setting), Once (Scrolls the song name
once)
While playing back a track (or group) with the menu browse
mode, you can switch the playback information (such as song
name, elapsed time, artist name, or album name) displayed in the
front panel display by pressing
or
.
English
37 En
TROUBLESHOOTING
Troubleshooting
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
YAMAHA dealer or service center.
Receiver (RX-E410)
■ General
Problem
Cause
Remedy
See
page
The receiver fails to
turn on or enters the
standby mode soon
after the power is
turned on.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
17
The receiver has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set the receiver to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and then
use it normally.
—
No sound
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
12
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or the input selection keys
on the remote control).
—
Speaker connections are not secure.
Secure the connections.
13
The volume is turned down.
Turn up the volume.
—
Signals the receiver cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by the
receiver.
—
The sound suddenly
goes off.
The timer has turned off the receiver.
Turn on the receiver, and play the source again.
—
Sound is heard from
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
13
There is noise
interference from
digital or radio
frequency equipment.
The receiver is too close to the digital or
high-frequency equipment.
Move the receiver further away from such equipment.
—
38 En
Troubleshooting
■ Tuner
Problem
FM stereo reception is
noisy.
FM
AM
Cause
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Remedy
See
page
Check the antenna connections.
14
Try using a high-quality directional FM
antenna.
—
Use the manual tuning method.
26
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference.
Adjust the antenna position to eliminate
multi-path interference.
—
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak.
Use a high-quality directional FM antenna.
—
Use the manual tuning method.
26
Previously preset
stations can no longer
be tuned into.
The receiver has been disconnected for
a long period.
Set preset stations
27
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for the best reception.
14
Use the manual tuning method.
26
There are continuous
crackling and hissing
noises.
Noises result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
—
There are buzzing and
whining noises.
A TV set is being used nearby.
Move the receiver away from the TV set.
—
ADDITIONAL
INFORMATION
English
39 En
Troubleshooting
■ iPod
Note
In case of a transmission error without a status message appearing in the front panel of the receiver, check the connection to your iPod
(see page 16).
Status message
Loading...
Cause
Remedy
See
page
The receiver is in the middle of
recognizing the connection with your
iPod.
The receiver is in the middle of acquiring
song lists from your iPod.
Connect error
There is a problem with the signal path
from your iPod to the receiver.
Turn off the receiver and reconnect the YAMAHA
iPod universal dock to the DOCK terminal of the
receiver.
16
Try resetting your iPod.
—
Only iPod (Click and Wheel), iPod nano, and iPod
mini are supported.
—
Unknown type
The iPod being used is not supported by
the receiver.
iPod connected
Your iPod is properly stationed in a
YAMAHA iPod universal dock (such as
YDS-10 sold separately) connected to the
DOCK terminal of the receiver, and the
connection between your iPod and the
receiver is complete.
Disconnected
Your iPod was removed from a YAMAHA
iPod universal dock (such as YDS-10 sold
separately) connected to the DOCK
terminal of the receiver.
Station your iPod back in a YAMAHA iPod universal
dock (such as YDS-10 sold separately) connected to
the DOCK terminal of the receiver.
16
Unable to play
The receiver cannot play back the songs
currently stored on your iPod.
Check that the songs currently stored on your iPod
are playable.
—
Store some other playable music files on your iPod.
—
40 En
Troubleshooting
CD player (CDX-E410)
Problem
Cause
Remedy
See
page
Power turns on but
immediately shuts off.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
17
Power immediately
shuts off during
playback.
Auto-standby function of the receiver
works when the receiver can not receive
the playing signal transmitted from the
CD player with the system control cable
for 30 minutes.
Check the connection of the system control cable
between the receiver and the CD player.
12
No sound or distorted
sound
The sampling rate of a MP3 or WMA file
may not be compatible with the CD
player.
Check the sampling rate and bit rate of an MP3 or
WMA file are compatible with the CD player.
42
No audio at digital
output
Incorrect digital cable connections.
Connect the digital cables properly.
15
The disc being played back may not be
compatible with the CD player.
Check that the disc is compatible with the CD player.
42
You may use a CD-R/RW that is not
finalized.
Finalize the CD-R/RW.
—
The disc label may not be facing up.
Check that the disc label is facing up.
—
The disc may be defective.
Try to play back another disc. If the same problem
does not happen, the disc you want to play back is
defective.
—
MP3/WMA disc may not contain
sufficient music tracks to be played back.
Check that your MP3/WMA disc contains at least 5
MP3/WMA music files.
—
The sampling rate of a MP3 or WMA file
may not be compatible with the CD
player.
Check the sampling rate and bit rate of an MP3 or
WMA file are compatible with the CD player.
42
The disc lens may be dirty.
Use a lens cleaner to clean the lens.
42
Disc playback does
not start.
The CD player does
not read CDs.
Remote control
Problem
The remote control
does not work nor
function properly.
Cause
Remedy
See
page
The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees
off-axis from the front panel.
11
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this system.
—
The batteries are weak.
Replace all batteries.
11
The system control cable is disconnected
from the system connector jack of the
receiver and/or the CD player.
Connect the receiver and the CD player with the
system control cable firmly.
12
ADDITIONAL
INFORMATION
Wrong distance or angle.
English
41 En
NOTES ON DISCS
Notes on Discs
Disc information
The following tables explain the disc types supported by
the CD player. Also, the CD player can play back 8-cm
(3-inch) compact discs.
y
Disc logo marks are printed on the disc and the disc jacket.
Handling a disc
• Do not touch the surface of the
disc. Hold a disc by its edge and
center hole.
• Do not leave a disc in the tray when
you are not playing it.
• Do not write on the disc with a pencil or other marker.
• Do not stick tape, seals or other attachments to a disc, and do
not bring into contact with glue.
• Do not use a protective cover to prevent scratches.
• Do not use a disc whose surface can be printed with a
commercially available label printer.
• Do not put a disc in a place with
direct sunlight, high
Caution
temperature, high humidity or a
lot of dust.
Note
Do not load any other type of disc into the CD player. Doing so
may damage the CD player.
The CD player can play the following data discs
(For MP3 and WMA files, the parenthetic words
represent the compatible sampling rate and bit
rate):
– MP3 files, recorded on CD-R/RW (fs 44.1, 48 kHz/
32, 64, 96, 128, 160, 192, 256, or 320 kbps and
variable bit encoded MP3 files (CBR and VBR))
– WMA files, recorded on CD-R/RW (When in fs
44.1 kHz: 192 kbps or less and variable bit encoded
WMA files (CBR and VBR))
– ISO 9660 for CD-R/RW
Notes
• CD-R/RW cannot be played unless finalized.
• Some discs cannot be played depending on disc characteristics
or recording conditions.
• Do not use any non-standard shaped discs (heart-shaped, etc.).
• Do not use discs with tape, seals, or paste on their surface.
• Do not use discs with many scratches on their surface.
• Copyright-protected WMA files cannot be played back with the
CD player.
42 En
• If a disc becomes dirty, wipe it
with a clean, dry cloth from the
center out to the edge. Do not use
record cleaner or paint thinner.
• To avoid malfunction, do not use a
commercially available lens
cleaner.
Glossary
Audio information
■ MP3 (MPEG Audio Layer-3)
One of the audio compression methods used by MPEG. It
employs the irreversible compression method, which
achieves a high compression rate by thinning out the data
of hardly audible part to the human ears. It is said to be
capable of compressing the data quantity by about 1/11
(128 kbps) while maintaining a similar audio quality to
music CD.
Copyright and logo marks
MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson Multimedia.
iPod®
“iPod” is a trademark of Apple Computer, Inc., registered in the
U.S. and other countries.
■ PCM (Pulse Code Modulation)
A signal that is changed to digital format without
compression. A CD is recorded with 16-bit sound at
44.1 kHz. This signal also has a type called Packed PCM
(PPCM) that can be compressed without any loss of data.
■ Sampling frequency
The number of sampling (process for digitalizing analog
signals) per second. In principle, the higher the sampling
rate, the wider the frequency range that can be played
back, and the higher the quantized bit rate, the finer the
sound that can be reproduced.
■ Track
A CD can be divided into a number of segments (tracks).
Each division is called a track number.
■ WMA (Windows Media Audio)
An audio compression method developed by Microsoft
Corporation. It employs the irreversible compression
method, which achieves a high compression rate by
thinning out the data of hardly audible part to the human
ears. It is said to be capable of compressing the data
quantity by about 1/22 (64 kbps) while maintaining a
similar audio quality to music CD.
ADDITIONAL
INFORMATION
English
43 En
SPECIFICATIONS
Specifications
■ RX-E410
■ CDX-E410
AMPLIFIER SECTION
PLAYBACK SYSTEM
• Minimum RMS output power per channel
(6 Ω , 1 kHz, 0.1% THD).......................................... 55 W + 55 W
• Maximum RMS output power per channel
(6 Ω , 1 kHz, 1% THD)............................................. 65 W + 65 W
• Input sensitivity/Impedance
CD/TAPE/MD/AUX etc.......................................... 150 mV/47 kΩ
• Frequency Response
CD etc. ................................................... 20 Hz to 20 kHz ± 0.5 dB
• Total Harmonic Distortion (20 Hz to 20 kHz)
CD etc. 20 W, 6 Ω ......................................................0.04% or less
• Signal to Noise ratio (IHF-A network)
CD etc. (150 mV, Input shorted) .............................. 93 dB or more
• Output level/Impedance
PHONES ................................................................... 0.23 V/120 Ω
• CD, CD-R/RW
TUNER SECTION
FM Section
• Tuning Range ...................................................87.50 to 108.00 MHz
AM Section
• Tuning Range .......................................................... 531 to 1611 kHz
• Sensitivity
FM (S/N 68 dB) ................................................................... 6.0 µV
AM ..................................................................................600 µV/m
GENERAL
• Power Supply ..........................................................AC 230 V, 50 Hz
• Power consumption ................................................................. 130 W
• AC Outlets
U.K. model ....................................................1 (Total 100 W max.)
Europe model ................................................2 (Total 100 W max.)
• Standby Power consumption.................................................... 0.1 W
• Dimensions (W x H x D) .................................. 215 x 108 x 363 mm
• Weight ...................................................................................... 5.7 kg
44 En
LASER
•
•
•
•
Type .......................................................................................GaAlAs
Wave length ............................................................................780 nm
Emission Duration ............................................................ continuous
Laser Output ..............................................................max. 44.6 µW*
*This output is the value measured at a distance of about 200 mm
from the objective lens furface on the Optical Pick-up Block.
AUDIO PERFORMANCE
• Signal-Noise (1 kHz) .................................................105 dB or more
• Dynamic range (1 kHz) ...............................................95 dB or more
• Distortion and Noise (1 kHz)..................................... 0.003 % or less
GENERAL
•
•
•
•
Power supply ................................................... AC 220-240 V, 50 Hz
Power consumption .....................................................Approx. 13 W
Dimensions (W x H x D)...................................215 x 108 x 334 mm
Weight.......................................................................................2.8 kg
*Specifications are subject to change without notice.
Download PDF

advertising