Replacing the Imaging Cartridge

Replacing the Imaging Cartridge
Replacing the Imaging Cartridge
• Replacing the Imaging Cartridge
The massage is displayed on the control panel when the Imaging cartridge
replacement time is drawing near. Replace the Imaging Cartridge in the following
procedure.
The Imaging Cartridge should be installed in the order of Black(K), Cyan(C),
Magenta(M), and Yellow(Y) from the top.
As an example, the installing procedure of the Cyan(C) Imaging Cartridge is
described in this manual.
♦ CAUTION ♦
Perform the “Color adjustment” after replacing the Imaging Cartridge.
See the page of this manual for the “Color adjustment” procedure.
1. Open the front door.
♦ Checkpoint ♦
To prepare for spills of toner, spread the rug
such as newspapers in front of the printer and
then handle the various cartridges.
1
2. Remove the Toner Cartridge of Imaging Cartridge to be replaced.
(1) Turn the Toner Cartridge counterclockwise (about 30 degrees) until it stops.
“SET” to “INSERT”
(2) Pull out slowly the Toner Cartridge.
♦ Checkpoint ♦
To prepare for spills of toner, spread the rug
such as newspapers in front of the printer and
then handle the various cartridges.
♦ CAUTION ♦
When replacing the Toner Cartridge, hold
the upper side of the cartridge.
Holding the bottom of the cartridge may
make your hands dirty.
2
3. Turn slowly the Transfer belt unit release lever clockwise.
Turn the lever clockwise slowly
4. Pull the Inner door lever and then open the Inner door.
Inner door lever
3
5. Pull out straight the Imaging Cartridge to be replaced.
Place the withdrawn Imaging Cartridge gently on a flat surface,
such as on a desk.
♦ Checkpoint ♦
• Put the used Imaging Cartridge in the
plastic bag supplied when delivered and
put it in the individual packing box with
buffer material
• If there is no individual packing box,
please pack it in a cardboard box so as
to be able to prevent toner leakage or
damage during transport.
6. Make sure of the color of Imaging Cartridge to be replaced.
7. Peel off the Tape-1 securing the photoreceptor protective sheet (black sheet).
♦ CAUTION ♦
• Please handle the Imaging Cartridge with care.
• Please do not tilt too much the Imaging Cartridge.
• When removing the photoreceptor protective sheet, please be sure that the tape does not
stick to the developing roller and the photoreceptor.
• Please do not touch the developing roller surface and the photoreceptor surface.
• Please handle it gently without strongly grabbed.
4
8. Remove the photoreceptor protective material-1, protective sheet, tape-2(3
Places), and protective material-2.
♦ CAUTION ♦
Remove the all protective materials attached to the Imaging cartridge.
Don't forget to remove the “(3) protective sheet” of pictures below because it is small.
9. Hold the Imaging Cartridge horizontally with both hands and shake a few times
to the left and right. Then, remove the toner supply port seal and waste toner
outlet seal.
♦ CAUTON ♦
When shaking the Imaging Cartridge, please do not peel off the toner supply port seal and
waste toner outlet seal yet.
5
10. While keeping horizontally a new Imaging Cartridge, insert it straight aligning
the guide of cartridge with the guide rail of the printer.
11. Connect the connector by pressing the (1) part of the cartridge.
Then, push strongly (2) to (4) parts of the cartridge in numerical order.
Finally, push strong (5) part and make sure that all of them are securely
inserted.
(3)
(1)
(5)
(2)
(4)
♦ CAUTION ♦
If Imaging cartridge is incorrectly connected to the Printer.
It becomes cause of printed image fogging.
Push strongly (1) to (5)parts of the cartridge in numerical order.
(5)
(2)
(3)
(4)
6
(1)
12. Close the inner door
Push the inner door strongly until the top and bottom latches are engaged.
Push the inner door lever strongly.
Make sure that the top and bottom latches are engaged completely.
13. Turn slowly the transfer belt unit release lever counterclockwise.
7
14. Insert the Toner Cartridge.
Align the rib of the Toner Cartridge and the cutout of the insertion hole and insert
fully the Toner Cartridge into the printer.
♦ Checkpoint ♦
To prevent wrong insertion of the Toner
Cartridge, the structure of the rib of the
Toner Cartridge and the cutout of the
insertion hole is different for each color.
If trying to insert the Toner Cartridge with
the wrong color, the cartridge cannot be
inserted completely.
♦ CAUTION ♦
When replacing the Toner Cartridge, hold
the upper side of the cartridge.
Holding the bottom of the cartridge may
make your hands dirty.
Insert the cartridge label side up
label
8
15. Turn the Toner Cartridge clockwise (about 30 degrees) until it stops.
“INSERT” to “SET”
♦ CAUTION ♦
When the message "Please check the Toner Cartridge" is displayed on the Printer even if
inserted the Toner cartridge to the Printer.
The cause of this problem is connection failure of the circuit board of the Toner cartridge to the
printer. Please reinstall the Toner cartridge to the Printer.
16. Close the front door.
The procedure of replacing the imaging cartridge is finished.
Next, perform the "color adjustment".
9
• Performing the color adjustment for the DLP1000
The calibration to be performed varies depending on the "Print Type" and "Print
Quality" in the "Graphics" tab of the printer driver.
There are three types of calibration in all.
Depending on the output data, set the Print Type (Text, Illustration,
Photo/Graphics) and the Print Quality (Normal, Enhanced).
Print Quality
Print Type
Normal
Text
Enhanced
Calibration (B)
Illustration
Calibration (A)
Photo/Graphics
Calibration (C)
*The representation (A, B, C) of calibration is used for the explanation.
In the actual calibration, the representation (A, B, C) is not displayed.
*When the three types of calibration (A, B, C) are performed/registered in
advance, perform the color adjustment for this DLP1000 a total of three times.
• When the "Normal" in "Print Quality" is set
Perform common Calibration (A) regardless of the Print Type (Text, Illustration,
Photo/Graphics).
The calibration for each Print Type is not required.
• When the "Enhanced" in "Print Quality" is set
Perform two types of Calibrations (B, C) for each Print Type.
For the Print Type (Text), perform calibration (B).
For the Print Type (Illustration, Photo/Graphics ), perform Calibration (C).
♦ Checkpoint ♦
DLP1000 prints with three types of resolution depending on the print setting.
The resolution is not displayed on the setting menu of the printer driver.
• Calibration
A
600dpi
• Calibration
C
1200dpi
• Calibration
B
2400dpi
10
1. Open the printer property of the DLP1000 to select the "Graphics" tab.
2. Set the "Print Type" and "Print Quality".
♦ Checkpoint ♦
• The calibration to be performed may differ depending on the "Print Type" and "Print Quality".
• The representation (A, B, C) of calibration is used for the explanation.
In the actual calibration, the representation (A, B, C) is not displayed.
• It takes about one munite for calibration (A) and (C), about four munites for calibration (B).
Print Quality
Print Type
Normal
Text
Illustration
Enhanced
Calibration (B)
Calibration (A)
Photo/Graphics
3. Select the "Printer Information" tab.
11
Calibration (C)
4. Press the [Color adjustment...] button.
5. Press the [Calibration execution] button to perform the calibration.
During the calibration, The color adjustment is performed using the test pattern
in the DLP1000. "The printer is being calibrated" message is displayed on the
control panel of the DLP1000 during the calibration.
12
♦ CAUTION ♦
• Do not turn off the DLP-1000’s power during calibration. Such action may cause it to
break down.
• When the messages shown below appears, Press [OK] to continue the calibration.
Cancel
Cancel
6. When the "Ready" is displayed on the printer screen,
the calibration is completed.
Press the [Close] button of the printer driver to close the "Color adjustment"
screen.
When you continue to perform the calibration in other combinations, change the
settings of the "Print Type" and "Print Quality"
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising