CL-41/51/98/741/811/821/831 Color

CL-41/51/98/741/811/821/831 Color
User’s Guide
Maintenance Instruction
CL 41
Avoid printing without ink by performing a “top up” approach. This is meant by refilling small amount of
ink into the cartridge from time to time instead of waiting till the ink is exhausted from the cartridge.
Avoid exposing the cartridge to air for too long (more than 5 hours) as ink will dry up at print head and
clog it.
Avoid over refilling and to ensure no dripping before installing the cartridge back into the printer.
TROUBLE SHOOTING TIPS
Problem
1. Ink dripping from print head.
Possible Cause
Overfilling.
2. Print quality not good.
Clogged or damaged print head.
3. Print quality not good after
running cleaning utility.
Clogged or air trapped at print
head.
4. Print quality not good after
running cleaning utility and
soaking in hot water.
Damaged or air trapped at print
head.
5. Print quality not good after running
cleaning utility, soaking in hot water
and left unused for 12 hours.
Damaged print head.
No possible repair. Change a new
cartridge.
6. Color different or incorrect.
Filling wrong ink in the wrong
column, overfilling or cartridge
not in upright position when
filling was done.
Run nozzle check to determine color
mix. Clear mix color by printing
following color until ink is exhausted
from cartridge. Conduct a refill for
color exhausted.
7. Cartridge not identified by printer.
Poor contact at copper
connectors.
Wipe copper connectors (with alcohol
solutions) or use an eraser to rub on
copper connectors.
For support and more details to solving your technical issues,
please visit www.saintink.com for more information.
Information provided here are subject to change without notice.
Saintink is not responsible for any damages direct or indirect
arising from or related to the used of this information.
Saintink Incorporation (M) Sdn Bhd.
C41, Jln 2A, Kawasan Perindustrian Sg. Lalang,
08000 Sg.Petani, Kedah, Malaysia.
All brand names & trademarks are the properties of their respective holders
and are referred to here for descriptive purposes only.
Remedy
Stamp print head on tissue until ink stop
dripping.
Run head cleaning utility.
Soak print head (only print head portion)
in hot water for few second and clean
with tissue.
Leave cartridge in the printer for
12 hours and perform a nozzle
check subsequently.
Compatible Cartridge for
Canon # CL-41/51/98/741/811/821/831
Pixma iP1200/1300/1600/1700/1880/1980/
2200/2580/2680/2770/6210D/6220D/6320D,
E500/E600, MG2170/MG3170/MG4170,
MP145/150/160/170/180/198/228/245/258/
450/460/476/486/496,
MX308/318/328/338/347/357/416.
User’s Guide
>> READ THIS BEFORE REFILLING
Technical details on your CANON Cartridge
-The cartridge is embedded with a print head. The print head is a delicate
component and should be handled with a proper care. Avoid touching the print head.
-Fine electronics at the print head allow the ink to be pumped out in small volume.
These electronics are sensitive and are connected to the printer via a thin PC film
at the side.
-To continue printing without ink will damage the print head as this electronic will get
heated up. Once damaged, the cartridge cannot be used.
CANON >> CL - 41 / 51 / 98 / 741 / 811 / 821 / 831
cap
1.
2.
label
3.
drill bit
magenta
needle
plunger
1
yellow
3
2
cyan
Remove the cap then attach the needle to the
ink tube. Fix the plunger (per diagram) to allow
ease of pressing.
4.
Remove the label on the
cartridge.
5.
dialog box
magenta
cyan
yellow
Push the needle straight into
the cartridge and pull out a
little (2mm). Slowly press the
plunger to inject about 3ml
(per color) of ink into the
cartridge. Ensure cartridge
is in upright position. Stop
refilling if ink start to drip
at print head.
Drill a hole on the cartridge
lid for each color indicated
as shown above by turning the
drill bit clockwise. Ensure
correct position of the drill
hole.
6.
Reattach cap to
needle, keep ink out
of children reach and
store ink in a cool and
dry place.
Install the cartridge back into
the printer. Do a nozzle check.
Click OK when this dialog box
is shown. If the result of the
nozzle check is not good,
execute deep cleaning and
check print out. Repeat deep
cleaning if necessary.
Cartridge Holder
CARTRIDGE HOLDER AVAILABLE.
Caution
A dialog box might appear after the second refill.
Just follow the screen instruction to continue printing.
The refilled cartridge will not affect the printer as
long as there are still ink in the cartridge.
Rev-07/072012
To be bought separately.
3cc syringe
Note : In improving the print
quality, this holder is used for
cleaning the cartridge nozzle.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising