4-CHANNEL RC MINI QUAD-COPTER

4-CHANNEL RC MINI QUAD-COPTER
slipstream
TM
MAINTENANCE
1. Clean the quad-copter with a clean, soft cloth.
2. Do not leave the quad-copter in the sun or a bright light.
3. Do not expose quad-copter or its electronic parts to moisture or water.
4. Regularly check connections and other parts.
5. If you find any defective part, stop flying until the repair.
SLIPSTREAM
4-CHANNEL RC MINI QUAD-COPTER
Power Switch
PRE-FLIGHT
Thank you for your purchase of Protocol’s Slipstream 4-Channel 2.4 Ghz
Radio Controlled Mini Quad-Copter with Gyro. You are about to experience
the best of what remote control flight has to offer. We strongly recommend
that you take the time to read this manual thoroughly. It contains many tips
and instructions on how to get the most of this aircraft and maintain it for long life.
Speed Switch
As with any aircraft, this is a precision flying machine. Treat it well and enjoy all
the fun it has to offer, flight after flight.
Throttle
Forward/backward
L/R Direction Stick
L/R Direction Stick (Bank)
Flip button
SCHEMATIC
Step 1: Plug the cable
into the socket on the
Slipstream and place
it on a flat surface to
allow calibration.
Rotor
Motor
ILLUSTRATION ON QUAD-COPTER CONTROLLER
Step 2: Slide power
switch to “ON”
Canopy (Top)
Step 3: Move both throttle
and direction stick to the
lower left and lower right
corners respectively. The
LED light on Slipstream
will flash indicating it
is synced.
Power Indicator
Red (low power when flashing slow)
NOTE
4-CHANNEL RADIO CONTROLLED
Canopy (Bottom)
MINI QUAD-COPTER
FEATURING:
1. Four-Rotor design allows great speed and maneuverability for both Indoor and Outdoor use.
2. Built-in multi-axis Gyro ensures excellent stability.
3. Modular design for increased ease of maintenance.
4. 360-degree 3-dimensional stunt and tumbling function
The materials and specifications stated in this instruction manual are for reference only.
1. If the Slipstream and the remote do not sync after following the Pre-Flight checklist, reverse the
first two steps of the process. Turn the remote off and unplug the cable from the Slipstream. Then,
turn on the remote first and then plug the cable back into the Slipstream to turn it on. Follow with
Step 3.
2. Turn on the controller; if, after 30 seconds, it has not recognized the helicopter, turn off controller
to retry synchronization.
3. If the Slipstream is unsteady in flight, it may not have been able to calibrate horizontally; Power
down both vehicle and remote and restart pre-flight procedure.
Remote Control
SAFETY AND PRECAUTIONS
1. Keep small parts out of reach of children to avoid accidents.
2. The quad-copter is powerful and fast; accelerate gently to avoid damage and accidents.
3. After flying, disconnect the battery.
4. Keep the battery away from heat sources and / or fire.
5. Keep the quad-copter at a distance of at least 2 meters from yourself, others, and obstacles
to prevent damage.
6. Children should operate the quad-copter only under adult supervision.
7. The remote controller batteries can not be recharged. Do not mix new batteries with old batteries
or mix batteries of different types.
8. Always turn off both the transmitter and quad-copter when not in use.
9. Never attempt to short-circuit the battery terminals or the quad-copter.
SLIPSTREAM CONTROL
Charging the Quad-Copter’s On-Board Battery
Unplug the charging cable from the aircraft canopy, connect this to the supplied USB
charging cable. Insert the USB end of the charging cable into the USB port of any computer
(or a USB port power adapter) to begin charging aircraft. The red LED indicator will be on
during charging and will go off when the charging cycle has completed. Once fully charged,
plug charging cable back into canopy. The aircraft is now powered on.
50 minutes of charging yields 6-8 minutes of flight
1. When using a computer USB port as
power source, remember to unplug the
USB cable prior to shutting down
computer.
2. Take care to insert charging cable in
correct orientation as reversing the
polarity may lead to malfunction.
Move the left stick to the right.
Bank
left
Turn
right
Battery Cover
Unscrew and remove battery cover from controller, insert 3 ‘AAA’ batteries, noting polarity indicators.
Replace battery cover.
1. Install batteries carefully.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries.
Once you are familiar with the basics of quad-copter flight, you can try some
advanced maneuvers! At a height of at least 10 feet, press the right direction stick
once and you will hear it beep twice. Then move the right stick in whichever direction
desired to perform a 360-degree flip in that direction. After the flip, the Slipstream will
then restore to default status.
Move the right stick to the left.
Move the right stick to the right.
Move the left stick to the left.
Bank
right
Turn
left
Left Flip
Right Flip
GO UP
Front Flip
Rear Flip
FORWARD
1. When charging, place product on a dry, well-ventilated surface and keep away from heat
sources.
2. Always use adult supervision while charging.
3. As battery temperature is high immediately after flight, charge after cooling down for
higher efficiency.
4. Do not strike or subject battery to hard impacts or sharp surfaces.
5. Do not use any other charger than that which is supplied with this item.
6. Do not use or leave battery near a heat source such as a fire or space heater; exposure to
heat may result in reduced performance or in some cases dangerous conditions.
7. If battery is left in charging state for an extended period of time after being fully charged,
the battery may automatically discharge.
8. Never leave the battery unattended during charging.
360°
flip
360°
flip
Move the right stick forward.
Move the left stick upward.
*Slipstream uses a 3.7V 250MA Li Po Battery
360°
flip
360°
flip
Press and release to flip.
TROUBLESHOOTING
Symptom
Speed Switch
Slipstream
does not
respond
Move the right stick backward.
Move the left stick down.
1. Do not immerse or submerge battery in water; store in a cool, dry location.
2. In order to increase battery longevity, avoid repeat charging and excessive discharging.
3. Charge battery to approximately 55% capacity prior to long-term storage.
4. If battery sees no use for extended periods of time, it is recommended that battery voltage is
kept above 3V. Check monthly and recharge as needed.
5. Do not disassemble battery.
3X 1.5V AAA Batteries
GO DOWN
BACK
Possible Cause
Potential Solution
1. Communication between controller
and aircraft was not synchronized during
synchronization effort.
2. Battery power depleted on either aircraft,
controller, or both.
Response to 1. Controller battery power nearly depleted.
control inputs
intermittent
2. Aircraft antenna is damaged.
or erratic
The Slipstream
will not hover
or strafe
correctly
1. The aircraft was not on level ground
during synchronization.
2. Trim settings are incorrect.
Note: While fine-tuning flight characteristics, maintain constant position and altitude.
-5-
-6-
1. To synchronize, turn on controller, then
turn on aircraft and place it on level
ground. Move throttle stick all the way
forward, then all the way back.
2. Charge aircraft and/or replace
batteries in controller.
1. Replace batteries in controller.
2. Repair antenna.
1. Re-synchronize aircraft and controller.
2. Reset the trim buttons on the controller
and re-trim flight controls.
Thank you for your purchase of Protocol's Slipstream 4-Channel RC Mini Quad-Copter!
We know that accidents can sometimes happen and that is why we offer spare parts kits
on our website: ProtocolNY.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising