Pellet Stove P955 - P956
The instruction manual is an integral part of the product.
INSTRUCTIONS FOR INSTALLATION,
USE AND MAINTENANCE
Please read this entire manual before installation and use of this
pellet fuel-burning room heater. Failure to follow these instructions
could result in property damage, bodily injiury or even death.
Contact local building or fire officials about restrictions and
installation inspection requirements in your area.
Save these Instructions.
English
Pellet Stove P955 - P956
Dear Customer,
Thank you for having chosen one of our products, which is the result of years of experience and continuous research aimed at making a superior
product in terms of safety, reliability and performance.
This booklet contains information and advice for safe and efficient use of your product.
DT2010001-01
English
IMPORTANT INFORMATION
DT2010208-08
The following symbols are used in some parts of the booklet:
aaCAUTION: for actions that require particular caution and
suitable preparation.
ddFORBIDDEN: for actions that UNDER NO CIRCUMSTANCES
must be carried out.
aaContact local building autorithy (such as municipal building
department, fire department, fire prevention, bureau. etc.)
before installation to determine if a permit and/or inspection
is required.
•This instruction booklet has been prepared by the manufacturer and is
an integral part of the product. In the event of sale or relocation of the
product make sure this booklet accompanies it, since the information
contained in it is intended for the purchaser and for anyone involved
in the installation, use and maintenance of the product.
•Read the instructions and the technical information contained in
this booklet carefully before proceeding with installation, use or any
repairs.
•The observance of the instructions and technical information in this
instruction booklet guarantees the safety of persons and property; it
also ensures more efficient operation and an increased lifespan.
•Gruppo Piazzetta S.p.A. cannot be held responsible for damage or
injury due to failure to comply with the instructions for installation,
use and maintenance given in this booklet, or due to unauthorised
alterations or to the use of other than original spare parts.
•Appliance installation and use must conform with the manufacturer’s
instructions as well as with European and national legislation and
local regulations.
•Installation, electrical connection, checks, maintenance and repairs
are operations which must be carried out exclusively by qualified and
authorised personal with specialised knowledge of the product.
•The wall against which the product is to be placed must not be of
wood or any other flammable material. For correct installation it is
also important to comply with the section entitled “MINIMUM SAFETY
DISTANCES”.
•Before installing the product read all instruction booklets relevant to
the cladding, the ventilation kit and any other accessory.
•Check that the floor where the product is to be installed is perfectly
level.
•When handling the steel parts of the cladding it is advisable to use
clean cotton gloves to avoid leaving fingerprints that are difficult to
remove at first time of cleaning.
•The stove must be assembled by at least two persons.
•Connect the pellet stove to the electricity supply only after it has been
connected by an expert to the flueway.
•The plug at the end of the power cable must be easily accessible after
installation.
•Use only recommended wood pellets in the pellet stove (refer to
section entitled “FUEL”).
•Never use liquid fuels to light the pellet stove or to relight the embers.
•Ensure that the area where the stove is installed is properly ventilated
while the stove is lit.
•In the event of malfunctioning the fuel supply will be stopped. Restart
the stove only after having eliminated the cause of the malfunction.
•Stop using the product in the event of fault or malfunctioning.
•Do not remove the protective grille from the pellet hopper.
•Any build-up of unused pellets in the burner left over from repeated
failed ignitions must be removed before attempting to light the stove
again.
•Stove operation can result in surfaces, handles, flue pipe and glass
becoming extremely hot. When the stove is in operation, only touch
these parts if wearing protective clothing otherwise use suitable tools.
•Because of the build-up of heat on the glass, take care that those who
are unfamiliar with stove operation do not linger near the stove.
•This appliance must not be used by persons (including children) with
reduced physical, sensory or mental capacities, or lack of experience
or knowledge unless they are supervised or instructed on use of the
appliance by the person who is responsible for its safety.
•Creaking may be heard while the stove is in operation or cooling
down. This is not to be considered a defect, but is a consequence of
thermal expansion of the component materials.
•The product you have purchased may different slightly from the one
illustrated in this booklet since the pictures are only given as an
indication and not an exact portrayal.
aaIn the event of difficulties or if you are unable to understand
the instruction booklet, contact your local dealer.
ddDo not place objects which are not heat-resistant on top of
the stove or within the recommended minimum safety area.
ddDo not open the door while the stove is in operation or operate
the stove when the glass is broken.
See the guarantee certificate enclosed with the product for the terms, limitations and exclusions.
In line with its policy of constant product improvement and renewal, the manufacturer may make changes without notice.
This document is the property of Gruppo Piazzetta S.p.A.; no part of it may be disclosed to third parties without the written permission of
Gruppo Piazzetta S.p.A. All rights reserved by Gruppo Piazzetta S.p.A..
2
H07025240/DT2000723 – 01
CONTENTS
DT2010187-00
Page
1.0
GENERAL RULES
1.1 Soot inspection
1.2 Fresh air intake
1.3 Outside combustion air
1.4 Installation environment
1.5 Capacity load of the floor
1.6 Minimum safety distances
1.7Flueway
1.8 Interior vent installation
1.9 Connecting to a conventional chimney
1.10 Installing into an existing fireplace chimney
1.11 Short rise installation – Wall outlet
1.12 Venting: termination requirements
1.13 Prevention of domestic fires
1.14 Mobile home installation
TECHNICAL CHARACTERISTICS AND SPECIFICATIONS
2.0
2.1Features
2.2 Technical data
2.3 Accessories and equipment
2.4 Product identification data
2.5 Dimensional diagram P955
2.6 Dimensional diagram P956
2.7 Wiring diagram P955 - P956
3.0FUEL
4.0
PREPARING FOR INSTALLATION
5.0INSTALLATION
5.1 Multifuoco System
5.2 Electrical connections and controls
5.3 Installing the external thermostat
5.4 Installing the Y-element (optional)
6.0USE
6.1 Loading the pellets
6.2 Remote control
6.3 Lighting for the first time
6.4 Startup and normal operation
6.5Troubleshooting
6.6 Control panel
6.7 Setting the language
6.8Programming
6.9 Setting unit of temperature measurement
6.10 Programming the clock
6.11Timer
6.12Multicomfort
6.13 Energy Saving
6.14 Parameter menu
6.15 Enable beep (audio signal)
6.16 Stove status
6.17 Modifying the transmission unit
6.18 ‘Multifuoco’ system operation
6.19 Safety devices
6.20 Opening the door
6.21Humidifier
6.22 Disposal of ashes
7.0MAINTENANCE
7.1 Cleaning the grate and the grate support
7.2 Cleaning the ash tray
7.3 Cleaning the firebox 7.4 Cleaning the smoke chamber
7.5 Cleaning the flue system
7.6 Cleaning the ceramic cladding
7.7 Cleaning the enamelled metal parts
7.8 Cleaning the glass (daily)
7.9 Replacing the window
7.10 Replacing the remote control batteries
7.11 Cleaning the fans
7.12 When not in use
7.13 Extraordinary maintenance
8.0TROUBLESHOOTING
8.1 Replacing the fuses
Reference standards
4
4
5
5
5
6
6
7
9
10
11
11
12
13
14
15
15
15
16
16
17
17
18
19
19
20
20
23
23
24
25
25
26
27
27
30
33
33
34
35
36
37
43
43
45
46
46
47
47
48
50
51
51
52
52
52
52
53
53
54
54
54
54
55
55
55
55
56
59
59
English
SectionTitle
This booklet code H07025240 / DT2000723 - 01 (05/2011) comprises 60 pages.
H07025240/DT2000723 – 01
3
1.0 GENERAL RULES
DT2010216-05
Ensure that the installation of your product conforms to all the indications given below.
Fig. 1
English
CHIMNEY STACK
SINGLE FLUEWAY OR CHIMNEY
CONNECTION TO FLUE
SOOT INSPECTION APERTURE
FRESH AIR INTAKE
END ELBOW
WITH INSPECTION WINDOW
MINIMUM SAFETY DISTANCES
CAPACITY LOAD OF THE FLOOR
DT2030321-00
DT2010031-01
1.1 Soot inspection
We recommend that the flue must have a chamber for collecting solid matter and any condensate located below the connection and which may be
easily inspected by means of an airtight door. (Fig. 1)
4
H07025240/DT2000723 – 01
DT2010539-03
1.2 Fresh air intake
To ensure trouble-free operation the stove must have the necessary
air available for combustion and this is provided through the fresh air
intake.
Fig. 2
English
The fresh air intake must:
-- have a total free cross section at least equal to the size given in the
paragraph “TECHNICAL DATA”;
-- be protected by a grille or suitable guard provided it does not reduce
the minimum recommended section;
-- be in a position whereby it cannot be obstructed.
DT2030054-00
DT2010539-03
1.3 Outside combustion air
It is recommended that the stove be connected to an outside source of
combustion air under certain conditions (negative pressure).
To install outside air use any 2” I.D. flexible metal hose or rigid metal
pipe (conduit).
It must be connected around (NOT INSIDE) the combustion air inlet tube
(Fig. 3).
Increase the outside air pipe diameter to 3” for runs over 15 ft (4,5 m)
and elevation over 4 ft (1 m).
Fig. 3
2" O.D.
COMBUSTION AIR TUBE
aaLong runs should be avoided.
Be careful not to pinch or bend the outside air pipe with too small a
radius.
Outside Air Pipe may be terminated flush with the outside wall but
should be protected from wind and weather by a hood.
aaThe outside air pipe must terminate above the maximum snow
line and at least 4 ft (1.2 m) below the exhaust vent outlet.
Take care not to draw cold air past water pipes that may freeze.
An open mesh screen should be placed over the outside air pipe opening
to prevent birds or rodents from nesting in the opening. Use an elbow or
shield to prevent prevailing winds from blowing directly into the outside
air intake pipe.
DT2033383-00
NOTE: Mesh screen should be no smaller than 1/4” by 1/4” (6,4 by 6,4
mm).
aaOutside
combustion air is required for all mobile home
installations and where building codes require.
aaIn
bedroom or bathroom installations the outside air
connection is required.
DT2010033-01
1.4 Installation environment
Contact local building authority before installation to determine if a permit and/or inspection is required.
When locating your appliance, consider the building structure to ensure the vent will not interfere with any ceiling joists, roof rafters, wall studs, water
pipes or electrical wiring. It may be easier to relocate the appliance than to rework the building structure.
The room where the appliance is to be installed must comply with the following requirements:
aaThey must not be used as a garage, store for combustible material or for activities with a risk of fire.
aaLocating the stove in a room with an explosive athmosphere is prohibited.
aaThey must not be in a vacuum in relation to the outside environment due to the effect of contrary draught caused by the presence in
the room where the fi replace is installed of another appliance or an extractor device.
ddThe stove or fireplace must not be used simultaneously with collective type ventilation ducts with or without extractor fan, other
devices or other appliances such as: forced ventilation systems or other heating systems using ventilation to change the air. Such
systems could cause a vacuum in the environment of installation even if installed in adjoining or communicating rooms.
H07025240/DT2000723 – 01
5
DT2010032-00
1.5 Capacity load of the floor
Check the load-bearing capacity of the floor, referring to the weight of the product given in the paragraph “TECHNICAL DATA”.
If the floor does not have a suitable load-bearing capacity, adequate countermeasures must be taken.
DT2011553-02
Fig. 4
REAR WALL
MIN 3"
MIN 4"
SIDE WALL
Install the product in compliance with the recommended safety distances
from heat sensitive or inflammable materials and not inflammable, from
load bearing and other walls and also from wooden elements, furniture,
etc.
The minimum distances are:
-- 4” (10 cm) from the wall behind the stove;
-- 6” (15 cm) from the side wall;
-- 3” (8 cm) from the flue gas outlet on the rear wall in case of ceiling
vent exit;
-- 32” (80 cm) in the heat radiation area and from the the hot air fan
outlet.
6"
4"
In the case of flooring that is heat sensitive or inflammable the floor
must be protected with non-combustible insulating material, e.g. sheets
of steel plate, marble, tiles, etc.
The floor protection must extend:
-- under the product;
-- a minimum of 6” (152 mm) in front of unit and beyond each side of the
fuel loading and ash removal opening (4” / 10 cm from the external
side of the coating).
6"
FLOOR PROTECTION
32"
HEAT RADIATION AREA
DT2033045-00
Fig. 5
REAR WALL
Connection to the flue must respect minimum safety distances from
heat-sensitive structural components or inflammable materials (wood
panelling, beams or ceilings, etc) shown in figures.
6"
MIN 3"
aaThe stove will become hot while in operation. Keep children
4"
6"
away from all stove surfaces.
Direct contact with stove while operating may cause skin
burns.
AT
HE
aaIt is recommended that greater distances than those indicated
VENT AT CLEARANCES SPECIFIED BY THE VENT
MANUFACTURER.
4"
6"
EA
AR
above be left all round the stove to make any necessary work
on the appliance easier.
ON
TI
EC
OT
PR
curtains, carpets, combustible liquids, etc. well away from the
stove when it is lit (minimum distance 32” / 80 cm).
R
OO
FL
32"
N
IO
AT
DI
RA
aaKeep any combustible product such as wooden furniture,
aaINSTALL
MIN 3"
SIDE WALL
English
1.6 Minimum safety distances
DT2033046-00
Fig. 6
Fig. 7
aaCertain local code restrictions may apply.
Check with Local Officials first before installing.
MIN 22"
(MIN 56 cm)
DT2033043-00
6
H07025240/DT2000723 – 01
MIN 3"
(MIN 7.7 cm)
DT2033044-00
DT2010229-05
1.7 Flueway
-- Dryer vent
-- Gas appliance (Type B) vent
-- PVC (plastic) pipe
-- Single wall stove pipe.
aaThe pellet stove is not the same as other stoves. It has a forced draught of flue gas by a fan, which keeps the firebox in a vacuum
and the entire flueway slightly pressurised. For this reason the flue must be completely airtight and correctly installed to ensure both
trouble-free operation and user safety.
•The flueway must be made by specialised personnel or firms, as outlined below.
•The flue must be installed in such a way as to guarantee that periodic cleaning can be carried out without dismantling any parts whatsoever.
•Pipes should always be sealed with silicone (not cement-based sealants) or specially adapted gaskets/seals, which retain their strength and
elasticity at high temperatures (>450°F / 230°C), and should be fixed with at least three sheet metal screws.
aaUsing the relative pipe clips, fix the flue to the wall so that it does not weigh on the smoke fan.
ddDO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
ddDO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
ddDo not connect to a flueway into which extractor hoods discharge vapours.
aaThe very hot exhaust gases may cause skin burns: keep a considerable distance away from the appliance.
aaThe exhaust gases from the combustion of pellets fuel may dirty the outside of the walls. To avoid such possibility terminate the vent
above the roof line.
Pipes and maximum usable lenghts
The exhaust pipe on all stoves is 2.95” O.D. so the stove was designed to accommodate a 3” stove pipe adaptor but the diameters of the pipes
depends on the type of installation. Your installation may require the use of 4” vent as shown in Table 1.
TABLE 1: CONNECTION TO FLUE PIPE - PIPE LENGTH
WITH 3” DIAMETER PIPE
WITH DOUBLE-WALLED 4”
DIAMETER PIPE
20’
25’
For installations more than 4000’ (1200 m) above sea level
-
Required
Maximum number of elbows
3
3
10’
10’
TYPE OF INSTALLATION
Maximum length (with three 90° elbows)
Length of horizontal sections with minimum 3% gradient
aaLosses in pressure associated with a 90° elbow can be compared to those incurred by three feet of pipe. An inspectable union-tee
can be considered equivalent to a 90° bend.
EXAMPLE: if installing a section greater than 20’ in length with 3” diameter pipe, calculate the maximum usable length in the following ways:
•If a maximum of three 90° elbows are used, the maximum length of the section will be 20’.
•If a maximum of two 90° elbows are used and bearing in mind that a 90° bend can be replaced by 3’ of pipe, the maximum length of the section
will be 20’+3’ = 23’.
•If a maximum of one 90° elbows is used and bearing in mind that a 90° bend can be replaced by one metre of pipe, the maximum length of the
section will be 20’+3’+3’ = 26’.
H07025240/DT2000723 – 01
7
English
aaThe stove requires a UL listed pellet vent. So the venting system shall be approved for pellet stoves by a certified testing Laboratory.
aaPL Vent must be used for venting all Freestanding stoves.
ddDo not use to vent pellet appliance these venting materials and products:
Where 4” diameter pipe must be used, connect it to the stove flue outlet
with a 3” union-tee then use a 3” – 4” adaptor (Fig. 8).
Fig. 8
Ø 4"
English
Ø 3"
PELLET
STOVE
TEE W/TEE CAP
DT2033009-00
Union-tee
The use of this type of fitting must allow for the collection of condensate
mixed with soot, which builds up inside the pipe.
It must also permit periodic cleaning of the flue without the need to
disassemble the pipes.
Single or double clean-out tees may be used.
An example is given below of a flueway connection, which allows
complete cleaning without having to disassemble the pipes (Fig. 9).
Fig. 9
INSULATING
MATERIAL
MIN 3"
TEE
DIRECTION
OF CLEANING
0 ÷ 10'
MIN 3%
TEE
H MIN 13'
DIRECTION
OF CLEANING
H MIN 5'
PELLET
STOVE
TEE
DIRECTION
OF CLEANING
DT2033008-00
8
H07025240/DT2000723 – 01
DT2010230-03
1.8 Interior vent installation
General vent layout is shown in figure and the procedure is as follows:
-- Position the appliance in desired location according to appliance
installation requirements.
-- Use a plumb line to determine location of PL Vent penetration of
ceiling.
-- Cut hole in ceiling and frame to appropriate opening size. Framing
material shall be the same as that of adjacent joist material.
-- Install Black Ceiling Support from below joist level and fasten with 4 –
1.5” spiral nails or screws (Fig. 10). Alternatively, a Support Assembly
may be used in place of the black celing support the support assembly
fits to ceiling opening from below and is fastened to joists with 4 1.5” spiral nails or screws (Fig. 10).
-- Insert first Vent section through Support and tighten the clamp screw.
Additionally fasten the vent with four screw (max ½” long) through the
support collar and into the vent skin.
-- Install the vent section(s) atop the first. Twist lock sections together
with a clock-wise turn. Before twisting, push vent sections firmly
together for proper lock barb engagement. Enough twisting force must
be applied to ensure that the collars will compress gasket material.
-- Firestops are required where the vent penetrates a floor or ceiling.
Cut a hole of the appropriate size in the ceiling/floor and install the
Firestop from above or below the joist. Fasten the Firestop with nails
through the corners (Fig. 10).
-- Elbows may be used to offset the Vent as necessary to jog around
joists or rafters. Keep use of elbows to a minimum as they reduce
drafts capacity of a vent.
-- Continue the Vent up through the roof line.
-- Slide the Flashing over the Vent until it sits on the roof line. Slip the
upper side of the Flashing base under the roof shingles. Nail the
flashing to the roof with a minimum of 8 roofing nails. Seals the
Flashing base with appropriate roofing mastic.
-- Slide the Storm Collar down the Vent until it sits on the flashing. Apply
a bead of silicone around the top of the Storm Collar.
-- Extend the PL Vent at least 12” above the roof line and terminate with a
PL listed Rain Cap (Fig. 11). If the Vent extends more than 6’ above the
roof penetreation, Roof Brace Poles and a Roof Brace Band must be
used to provide lateral support. In geographical regions experiencing
sustained low ambient temperature is recommended to enclose
exterior vents below the roof line. This help reduce condensation, soot
accumulation, and poor drafting.
-- Set the Rain Cap onto the top Vent section and twist lock it to the top
Vent section (Fig. 11).
-- Where the vent system penetrates the air/vapour barrier, the barrier
must be sealed to the ceiling support or firestop.
Fig. 10
RAIN CAP
STORM COLLAR
FLASHING
MINIMUM
CLEARANCE
MINIMUM
CLEARANCE
English
This kind of installation provides the natural draft that results from
a vertical rise avoiding smoke being released into the house when
electricity to the unit is interrupted while burning or smoldering pellets
remains in the burn grate.
3"
3"
FIRESTOP
ENCLOSURE
BLACK CEILING
SUPPORT
VENT
FRESH
AIR
INTAKE
TEE
DT2033034-00
Fig. 11
aaBe sure to use approved pellet vent pipe and ceiling passthrough fittings to go through combustible ceilings.
aaStrictly observe the PL Vent manufacturer’s safety
specifications when using ceiling pass through.
aaThe minimum clearance required between the PL Vent
and combustible material is 3”. Do not fill this space with
insulation or any other material. The air space is required for
the safe operation of the vent.
Ensure that all installation work is carried out to professional
standards.
aa
H07025240/DT2000723 – 01
RAIN CAP
12" MIN
TO ROOF
STORM COLLAR
FLASHING
MINIMUM
CLEARANCE
3"
SUPPORT
VENT SECTION
VENT
TEE
FRESH
AIR
INTAKE
DT2033035-00
9
DT2010232-02
1.9 Connecting to a conventional chimney
English
The stove may be connected to an existing Class A chimney or a masonry
chimney which meets the minimum requirements of NFPA 211. Using
this kind of installation the pellet stove is able to draft naturally without
exhaust blower operation (failure), reducing the probability of burn-back
and back-drafting.
Fig. 12
aaCheck that the connection to the flueway is gas/smoke-tight,
since the appliance operates in a vacuum.
MASONARY MUD THIMBLE
•If you wish to use an existing chimney it is strongly recommended that
you have it checked by a professional chimneysweep to ensure that it
is completely airtight (Fig. 12). The reason for this is that the smoke,
because it is slightly pressurised, can infiltrate any cracks in the flue
and escape into living spaces. If upon inspection you find that the
chimney is not completely sound, a relining of the chimney with either
PL vent or single wall stainless steel pipe may be necessary to bring
the chimney into compliance. If the existing chimney is wide enough
we recommend a pipe with a maximum diameter of 6”.
Put attention: some areas require that a liner must be always installed
to the top of the flue, as shown in figure even if the existing chimney
is in compliance (Fig. 13).
•When chimneys are relined, a chimney chase cap that reduces the
outlet of the chimney to the size of the liner is required. Extend the
exhaust vent above the chimney chase cap and finish it off with a
rain cap. A single wall liner may need to be insulated to maintain
adequate exhaust temperatures in the vent system.
PL ADAPTER
VENT
TEE (T)
DT2033037-00
Fig. 13
aaOutside Chimneys frequently are difficult to keep warm: it is
recommended that you insulate the liner.
MASONARY MUD THIMBLE
PL ADAPTER
•Venting into the side of an existing masonry chimney must be done
through a masonry thimble. When wall penetration is necessary to
access a masonry chimney, use a listed PL vent wall thimble (Fig.
12-13).
•When venting into a Class A steel chimney, (Fig. 14), use an appropriate
PL Vent adapter.
VENT
TEE (T)
aaStrictly
observe the PL Vent manufacturer’s safety
specifications.
aaThe
minimum clearance required between the PL Vent
and combustible material is 3”. Do not fill this space with
insulation or any other material. The air space is required for
the safe operation of the vent.
DT2033036-00
Fig. 14
MINIMUM
CLEARANCE
3"
aaEnsure that all installation work is carried out to professional
standards.
PL VENT ADAPTER
VENT
TEE
FRESH AIR
INTAKE
DT2033038-00
10
H07025240/DT2000723 – 01
DT2010232-02
1.10Installing into an existing fireplace chimney
Fig. 15
English
This kind of installation also provides natural draft in the event of a
power failure.
When installing as a hearth mount stove into a fireplace the unit must
either be relined, terminating above the chimney chase top, or positively
connected to the existing chimney system using a block off plate (Fig.
15-16).
An approved flex liner of PL vent must be used.
Put attention: some areas require that a liner must be always installed
to the top of the flue, as shown in figure 16.
aaA chimney system with known drafting problems may require
a liner, which may also need to be insulated to keep vent
system warm in cold chimney environment.
POSITIVE
BLOCK OFF PLATE
aaA cap shall be installed on the chimney to keep out rain.
aaStrictly observe the PL Vent manufacturer’s safety
TEE
specifications.
DT2033039-00
aaStrictly use listed pellet vent pipe fittings.
aaEnsure that all installation work is carried out to professional
Fig. 16
RAIN CAP
standards.
CHIMNEY FLASHING
PL VENT SYSTEM
POSITIVE
BLOCK OFF PLATE
TEE
DT2033040-00
DT2010232-02
1.11Short rise installation – Wall outlet
When terminating the exhaust system under the houses eaves, (Fig. 17)
the following requirements shall be fulfilled:
-- in selecting locations for appliance and vent, take into consideration
the NPFA 211 6-3.5 rule for distance of exit terminal from window
and openings;
-- run the vent vertically up the wall, ensuring to maintain a minimum of
3” clearance between the wall and vent;
-- a wall band must be installed just above the tee and at least every 6’
of vent rise or, if the rise is inferior, at the end of the vertical run;
-- after a rise of at least 5’ (1,5 m), install a 90° elbow aimed out from
the building wall;
-- attach a 45° elbow to the 90° elbow, aiming the second elbow down
toward the ground. Terminate the vent with a collar with screen
fastened to the 45° elbow;
-- the end of the vent pipe system must be at least twelve inches (12”)
from the wall and 24” below the eave.
Fig. 17
TERMINATION
COLLAR
90° ELBOW
WALL BAND
> 24"
>12"
45°
ELBOW
VENT
>5'
TEE
DT2033041-00
H07025240/DT2000723 – 01
11
This configuration will help prevent blockage of vent by snow drifts. Also the minimum vertical run of 5 feet (1,5 m) ensures the ventilation of the
exhaust in the event of a power failure, and allow for easier cleaning through cleanout on tee.
aaCertain local code restrictions may apply. Check with Local Officials first before installing.
aaStrictly observe the PL Vent manufacturer’s safety specifications when using wall pass through.
aaDouble wall PL vent requires a minimum of three inch (3”) clearance to combustibles and the use of listed wall thimble, fire stop or
English
roof flashing where applicable.
aaDo not place joints within wall pass-throughs.
aaEnsure that all installation work is carried out to professional standards.
DT2012157-00
1.12Venting: termination requirements
In determining optimum vent termination, carefully evaluate external
conditions especially when venting directly through a wall. Since you
must deal with odors, gases, and fly ash, consider aesthetics, prevailing
winds, distances from air inlets and combustibles, location of adjacent
structures and any code requirements.
•Exhaust must terminate above combustion air inlet elevation.
•Do not terminate vent in any enclosed or semi-enclosed area, (i.e.
Carports, garage, attic crawl space, etc.) or any location that can build
up a concentration of fumes.
•Terminals must not to be recessed into a wall or siding.
•When setting into place flue caps you should consider wind factors
such as dominate wind directions and currents in order to avoid down
draft, fly ash and/or smoke.
Fig. 18
1'
A
4'
4'
FRESH AIR
INTAKE
aaVent surfaces can get hot enough to cause burns if touched
by children.
Non-combustible shielding or guards may be required.
4'
1'
aaBe sure to use approved pellet vent pipe and wall pass-
4'
through fittings to go through combustible materials.
The type of installation must first be considered before determining
the exact location of the venting termination in relation ship to doors,
window, cavities or air vents. See figures 18-19.
Without outside combustion air connected to the unit.
For These types of installations please refer to the dimensions listed in
figure 18.
The clearance to a door, window or cavity must be at least:
-- 4’ (1.2 m) below;
-- 4’ (1.2 m) horizontally;
-- 1’ (305 mm) above.
A
10'
MECHANICAL
AIR SUPPLY INLET
A = EXHAUST TERMINAL
DT2033048-00
Fig. 19
FRESH AIR
INTAKE
A
The clearance to fresh air intake for combustion of the pellet stove
or any other appliance, or the non-mechanical air supply inlet to the
building must be at least 4’ (1.2 m).
The clearance to a mechanical air supply inlet to the building must be
at least 10’ (3 m).
9"
A
A
1,5'
1,5'
9"
A
1,5'
With outside combustion air connected to the unit.
For These types of installations please refer to the dimensions listed in
figure 19.
4'
A
MECHANICAL
AIR SUPPLY
INLET
8'
A = EXHAUST TERMINAL
DT2033047-00
12
H07025240/DT2000723 – 01
The clearance to a door, window or cavity must be at least:
-- 1.5’ (458 mm) below;
-- 1.5’ (458 mm) horizontally;
-- 9’’ (230 mm) above.
•The exhaust termination location (Fig. 20) must be at least:
-- 1’ (305 mm) above the ground level. Attention : the minimum vertical
rise shall always be not less than 5’ (1.5 m).
A flue at 1’ above ground is not enfant safe: we strongly reccomend
that the exhaust termination of flue be raised another 4’ to avoid
injury.
-- 7’ (2.1 m) from a public walkway, but attention to where the vent
shall end its course, as it is not to be in between or serve two family
dwellings and/or directly above side-walks or paved driveways;
-- 1’ (305 mm) from the wall penetration point;
-- 3’ (915 mm) from a gas meter/regulator assembly;
-- 3’ (915 mm) from any adjacent combustibles such as: adjacent
buildings, fences, protruding parts of the structure, roof eaves or
overhangs, plants, shrubs, etc.
English
The clearance to fresh air intake for combustion of the pellet stove
or any other appliance, or the non-mechanical air supply inlet to the
building must be at least 4’ (1.2 m).
The clearance to a mechanical air supply inlet to the building must be
at least 8’ (2.5 m).
Fig. 20
CLEARANCE TO WALL
PENETRATION POINT
aaThe exhaust gases from the combustion of pellets fuel may
dirty the outside of the walls.
To avoid such possibility terminate the vent above the roof
line.
CLEARANCE TO
PUBLIC WALKWAY
7'
CLEARANCE TO
COMBUSTIBLES
1'
3'
45° ELBOW
WITH
TERMINATION
COLLAR
THIMBLE
90° ELBOW
PUBLIC
WALKWAY
1'
VENT
COMBUSTIBLES
CLEARANCE TO
GROUND
TEE
DT2033042-00
aaEnsure that all installation work is carried out to professional
standards.
DT2010027-02
1.13Prevention of domestic fires
The product must be installed and used in compliance with the manufacturer’s instructions and European and national standards as well as local
regulations.
aaWhen a flue pipe passes through a wall or a ceiling, special installation methods must be applied (protection, thermal insulation,
distances from heat-sensitive materials, etc.) See the paragraph from “INTERIOR VENT INSTALLATION” to “SHORT RISE INSTALLATION
- WALL OUTLET”.
•It is also recommended that all elements made of combustible or inflammable material, such as beams, wooden furniture, curtaining, flammable
liquids, etc. be kept outside the heat radiation range of the stove and at a distance of at least 32” / 80 cm from the heating block.
•For other information, see the paragraph from “MINIMUM SAFETY DISTANCES” to “VENTING: TERMINATION REQUIREMENTS”.
•The flue pipe, chimney stack, chimney and fresh air intake must always be free of obstructions, clean and checked periodically, that is, at least
twice during the seasonal period from the lighting of the stove and during its use. When the stove has not been used for some time it is advisable
to carry out the checks mentioned above. For further information, consult a chimneysweep.
•Only use recommended fuels (See section “FUEL”).
H07025240/DT2000723 – 01
13
DT2010027-02
1.14Mobile home installation
The stove has been tested and listed for mobile home installations.
Fig. 21
English
Unit must be installed in accordance with the: Manufactured Home
and Safety Standard (HUD), CFR 3280, Part 24.
In addition to all previously detailed requirements, mobile home
installations must observe the following:
-- Permanently bolt the stove to the floor. Use 4 screws [A] through the
4 holes placed at left and right side in the base plate as shown in
figure 21.
-- Electrically ground the stove to the metal chassis of the home using a
number 8, gauge or larger copper wire [B].
-- Maintain an effective vapor barrier at location where PL vent exits the
structure.
-- Floor protection and clearances requirement must be followed
precisely as shown in the previous paragraphs.
-- PL Vent must be used for exhaust venting. (Single wall vent is not
allowed). Follow PL Vent manufacturer’s installation directions and
observe all listed clearances to combustibles.
-- Check any other local buildings codes or other codes that may apply.
FLOOR
PROTECTION
A
FLOOR
METAL CHASSIS
ddWARNING: DO NOT INSTALL IN A SLEEPING ROOM.
aaCombustion air must come from the outside of the mobile
home! Failure to do so may create negative pressure within
the mobile home and could disrupt proper venting and
operation of the pellet stove.
aaCAUTION:
THE STRUCTURAL INTEGRITY OF THE FLOORS,
WALLS, CEILING AND ROOF MUST BE MAINTAINED.
aaThe stove is hot while running. Keep children, clothing and
furniture away. Contact may cause skin burns.
aaKeep combustible materials such as grass, leaves,etc. at least
4 ft away from the point directly under the vent termination.
14
H07025240/DT2000723 – 01
B
DT2032938-00
2.0 TECHNICAL CHARACTERISTICS AND SPECIFICATIONS
DT2012360-00
Cladding:��������������������������in hand-made majolica
Front panel:����������������������in steel with grey enamel finish
Interior:�����������������������������in steel
Baffle plate and hearth:�����in cast iron
Grate:�������������������������������in cast iron
Door:��������������������������������in cast iron with ceramic glass heat resistant up to 1382°F / (750°C)
Handle:�����������������������������in steel with nickel-plated finish
Control panel:�������������������remote control with LCD and digital control panel on stove
Timer thermostat:�������������standard with daily, weekly and weekend programming modes divided into two time bands
Power setting:�������������������from 1 to 4
Ash drawer:����������������������removable
Fuel:���������������������������������natural pure wood pellets (see section “FUEL”)
Heating:����������������������������forced ventilation with the Multifuoco System, three fan settings, possibility of operation with room temperature setting as
measured by the remote control (see section “MULTICOMFORT”), front hot air outlet at bottom, set-up for ducting outlet
at rear (see section “MULTIFUOCO SYSTEM”)
Humidifier:������������������������stainless steel [contains 17 oz (50 cl) water P955 – 34 oz (100 cl) P956].
DT2012359-00
2.2 Technical data
P955
P956
P4
P1
P4
P1
(at rated power) (at minimum power) (at rated power) (at minimum power)
BTU/H / (kW) 37523 / (11.0)
11420 / (3.3)
37523 / (11.0)
11420 / (3.3)
lb/h / (kg/h)
4.38 / (1.99)
1.33 / (0.61)
4.38 / (1.99)
1.33 / (0.61)
%
86.5
80.0
86.5
80.0
A
2.9
2.9
W
320
320
W
85
85
V
120
120
Hz
60
60
lb / (kg)
44 / (20)
57 / (26)
in
Ø 2.95
Ø 2.95
2
2
in / (cm )
15.5 / (100)
15.5 / (100)
lb / (kg)
353 / (160)
353 / (160)
in / (cm)
31.1x26.7x50.8 / (79x68x129)
31.1x26.7x50.8 / (79x68x129)
Unit
Heat input
Burn rate
Overall efficiency
Rated current during ignition
Maximum power input during ignition
Power input at work
Electrical power supply voltage
Rated frequency
Fuel tank capacity
Exhaust outlet diameter
Fresh air intake with minimum useful section
Weight with cladding
Packing sizes (DxWxH)
Data obtained under laboratory conditions.
N.B.: The above data may vary according to the characteristics of the pellets being used. (See section “FUEL”).
H07025240/DT2000723 – 01
15
English
DT2010698-00
2.1 Features
DT2011790-00
English
2.3 Accessories and equipment
Description
NTC 10K room sensor
Flexible cable L = 5.9’ / (180 cm)
LCD Remote-control
Grate baffle plate
Silicone paint spray can
Humidifier
Detachable handle
In kit
In kit
In kit
In kit
In kit
In kit
In kit
DT2011541-00
2.4 Product identification data
Every product is identified by a rating plate showing the model and the performance of the appliance as well as a plate giving the serial number.
The rating plate is located on the rear panel of the stove, while the plate with the serial number is located on the underside of the hopper lid.
A label bearing the serial number is also applied on the cover last page of the “Installation, operation and maintenance” booklet.
Always give the information shown on these plates to the dealer or the Service Centre when requesting service or spare parts.
Fig. 23
Fig. 22
PRODUCT
NAME
DT2032939-00
16
H07025240/DT2000723 – 01
SERIAL NUMBER
DT2032204-00
DT2033371-00
English
2.5 Dimensional diagram P955
42,12"
(1070 mm)
Ø 1,97"
(50 mm)
Ø 2,95"
(75 mm)
16,25"
(413 mm)
8,07"
(205 mm)
6,89"
(175 mm)
8,74"
(222 mm)
0,79"
(20 mm)
3,94"
(100 mm)
5,98"
(152 mm)
19,69"
(500 mm)
23,61"
(600 mm)
Dimensions in inches (mm)
DT2033372-00
2.6 Dimensional diagram P956
43,33"
(1101 mm)
Ø 1,97"
(50 mm)
Ø 2,95"
(75 mm)
14,04"
(357 mm)
7,15"
(182 mm)
6,49"
(165 mm)
6,89"
(175 mm)
0,8"
(20 mm)
3,96"
(100 mm)
5,98"
(152 mm)
18,7"
(475 mm)
Dimensions in inches (mm)
23,27"
(591 mm)
H07025240/DT2000723 – 01
17
DT2033257-00
2.7 Wiring diagram P955 - P956
Capacitor
English
BLACK
BLACK
Receiver unit
YELLOW GREEN
Room fan
(blower)
WHITE
WHITE
BLUE
BROWN
Flat cable
FUN1 SCAMB
SPEED
FUN1
FUN2
SPEED
FUN2
Flue gas fan
AUX
Fuel feed
auger motor
BLACK
Ventilation
electronic board
BLUE
AUX
4 2
Power supply
with fuse
RED
N.O. Hopper lid
switch
(normally open)
N.O. Pressure switch
(normally open)
Igniter plug
RED
N.C. 80° Thermostat
(normally closed)
BLACK
18
H07025240/DT2000723 – 01
BLACK
BROWN
BLACK
WHITE
GRAY
YELLOW
GREEN
TERM.
-TC1+
N.AMB.
N.H2O
N.PEL.
WHITE
FAN2
FAN1
DISPLAY
ENC
+5V
GND
BLU
SERIALE
AL2
AL1
N
Motherboard
N.O. Fire door
switch
(normally open)
1
COC.
ACC.
Outside
thermostat
Smoke sensor
4 2
BLUE
BLUE
Room sensor
1
Capacitor
F
N
FUMI
SCAM.
Serial port DB9
BLACK
BROWN
BLUE
YELLOW GREEN
3.0 FUEL
DT2010233-04
Since the characteristics and quality of the pellet considerably
affect stove performance, efficiency and proper operation, we
recommend that you use high-quality pellets.
Gruppo Piazzetta S.p.A has tested and programmed its stoves and
can ensure best performance and trouble-free operation using
pellets with the following specific characteristics:
Pellet characteristics
Choosing other and unsuitable pellets
-- obstructs the grate and flue gas pipes;
-- increases fuel consumption;
-- reduces efficiency;
-- means that proper stove operation cannot be guaranteed;
-- causes dirt to build up on the glass;
-- leaves particles which have failed to burn and heavy cinders.
The presence of moisture in the pellets increases their volume and
causes them to split which in turn causes:
-- malfunction of the fuel-loading system;
-- inefficient combustion.
Pellets should be stored in a sheltered, dry place.
To use good quality pellets with dimensions and heat-producing
properties other than those recommended above, it will be necessary to
change the stove operating parameters.
aaThis “customisation” of stove settings must be carried out
Components
natural pure wood pellet
Length, approx.
¼” – 1 ¼” / (7 – 30 mm)
Diameter, approx.
0.23” – 0.25” / (6 – 6.5 mm)
Apparent density, approx.
40.5 lb/ft3 / (650 kg/m3)
Net heat value, approx.
8000 BTU/lb / (5 kWh/kg)
Moisture content, approx.
< 8%
Residual ash, approx.
< 0,5%
at a Gruppo Piazzetta S.p.A. Service Centre or by specially
qualified personnel authorised by Gruppo Piazzetta S.p.A.
aaUsing pellets that are out of date or not in conformity with
the manufacturer’s recommendations not only damages the
stove and jeopardises its performance, but can render the
guarantee null and void and relieves the manufacturer of all
liability.
Fig. 24
N.B. the above data refer to beech/fir wood pellets
To ensure trouble-free operation:
DO NOT use pellets with dimensions other than those recommended by
the manufacturer.
DO NOT use poor quality pellets containing sawdust, bark, maize, resins
or chemical substances, additives or adhesives.
DO NOT use damp pellets.
DT2030346-00
4.0 PREPARING FOR INSTALLATION
DT2010074-06
To prevent accidents or damage to the product we recommend the following:
-- unpacking and installation must be carried out by at least two people;
-- every operation involving movement of the product must be carried out with the proper tools in full compliance with current safety regulations;
-- the packaged product must be kept in the position according to the directions shown by the diagrams and notices on the pack;
-- if ropes, straps or chains are used, ensure that they are able to take the weight of the pack and that they are in good condition;
-- use slow continuous movements when moving the pack to avoid jerking the ropes, chains, etc.;
-- do not tilt the package excessively to avoid toppling;
-- never stand in the vicinity of loading/unloading equipment (forklift trucks, cranes etc).
aaUnpack the product being careful not to damage or scratch it, take the accessories pack and any pieces of polystyrene or cardboard
used to wedge moveable parts etc. out of the stove firebox.
Keep packaging (plastic bags, polystyrene, etc.) out of reach of children, since it could be a potential source of danger, and dispose
of according to local regulations.
aaInstallation and assembly of the stove must be carried out by qualified personnel.
H07025240/DT2000723 – 01
19
English
The wood pellet is obtained by pressing wood sawdust left over from
the working of natural dried wood. The typical small, cylindrical form is
obtained by passing the material through a die. Thanks to lignin, a natural
element which is released during the pressing of the raw material, the
pellets acquire a good consistency and compactness without requiring
treatment with additives or caking agents.
There are various types of pellet on the market with qualities and
characteristics that vary depending on the processes they have
undergone and the type of wood used in their production.
5.0 INSTALLATION
DT2010116-02
Pursuant to current regulations on the safety of electrical equipment, you must contact a Piazzetta After-Sales Service Centre or a qualified electrician
for all and any work connected with installation, maintenance or servicing that involves access to electrical parts.
English
Cladding
•Having completed assembly of the stove and installed any external room thermostat, proceed with assembly of the stove cladding, referring to the
ceramic cladding instruction booklet provided with the stove.
DT2010071-05
DT2012361-00
5.1 Multifuoco System
•Thanks to Piazzetta technology and R&D, this pellet stove offers the
advantages of the “Multifuoco system”, a system EXCLUSIVE to and
PATENTED by Gruppo Piazzetta S.p.A., a true innovation in the field of
pellet stoves.
•The “Multifuoco system” revolutionises all methods of heat circulation
currently in use in pellet stoves: the heat produced by the firebox is
not only circulated from the lower part of the stove into the room,
but hot air can also be ducted via Ø 3” / (Ø 75 mm) flexible pipes to
adjoining rooms (Fig. 26).
This exclusive floor-standing heat distribution system offers notable
advantages: even spread of temperatures (Fig. 25).
The hot air produced is propelled by a fan and distributed via the grille
in the bottom front of the stove.
Fig. 25
DT2030163-00
Fig. 26
•This grille is fitted with an adjustable flap.
•To direct the outflow of hot air as required, adjust the angle of the flap
by pressing on the part of it that projects (Fig. 27).
Instructions for ducting the hot air
•The fan kit, which propels hot air into the room, can be fitted with a
Y-element which effectively allows the hot air flow to be doubled up,
directing it via a flexible pipe also to the rear of the stove, from where
it can then be ducted to adjoining rooms.
•Some examples of possible installation are given below as well as
examples of how to duct the hot air in order to heat other rooms.
Such examples are given purely for demonstration purposes; best
efficiency can be obtained using Ø 3” / (Ø 75 mm) coated ducting
in accordance with instructions given in the sub-paragraph “Wall
and floor ducting” and with a maximum total flexible pipe length of
32.8’ / (10 m). This length consists of the sum of the single lengths
of flexible pipes.
DT2030162-00
Fig. 27
aaIt is of fundamental importance that when ducting heat from
the rear of the stove, the outlet vents near the stove or the
Y-element must not be closed in order to avoid overheating.
In cases where only one rear outlet from the fan is envisaged,
the outlet vent must always be kept open.
•The examples show the ducting. Each diagram gives just one example
of the many possible solutions.
DT2030310-01
20
H07025240/DT2000723 – 01
Solution 1 - Fig. 28 - 29:
The stove is installed in the room which is to be heated, with the hot
air directed to the front only, as when the stove arrives from the factory
(Fig. 28). Alternatively the air can flow to the rear by connecting a 3” / 75
mm-diameter flexible pipe to the fan outlet (Fig. 29). In this set-up the
stove heats the room where it is installed by radiation only, and heats
the adjoining room through the ductwork to the rear.
Fig. 28
aaFor the example shown in fig. 29 it is necessary to use an
English
outlet vent which is permanently open.
DT2030164-00
Fig. 29
Non-closable
vents
3.3’
Solution 2 - Fig. 30:
The stove is installed in the room to be heated with the hot air ducted
to the front and, with the installation of a Y-element, also to the rear
thereby allowing the heating of a second room. A Ø 3” / (Ø 75 mm)
flexible pipe with a maximum length of 32.8’ / (10 m) is connected to
the fan outlet (Fig. 30).
/ (1
m)
DT2030165-00
Fig. 30
Partially open vent
aaFor
the example shown in fig. 30 with single duct, the
outlet vent must be partially open but never closed to avoid
overheating.
32.8’ / (10 m)
DT2030166-00
Solution 3 - Fig. 31:
Extension of the previous solution, with the stove installed in the room
to be heated and the air flow ducted to the front and the rear, but using
a second Y-element to double the ducting at the rear as shown.
Maximum total length of the flexible pipe 32.8’ / (10 m). (Fig. 31).
Fig. 31
aaFor the example shown in fig. 31, for efficient ducting and to
avoid overheating, the outlet vent closest to the Y-element
must be partially open but never closed to avoid overheating.
19
.7’
/(
6m
)
Partially
open vent
6.5’
/ (2
m)
DT2030167-00
H07025240/DT2000723 – 01
21
Fig. 32
Fig. 33
DT2030168-00
Fig. 34
DT2030169-00
Fig. 35
aaIf the insulating material is not enclosed under the floor or
within the walls, it must be fixed to the surface with suitable
fastenings at intervals of 11.8” / (30 cm).
A few examples of how the flexible pipe can be installed in walls or
floors are given to the side.
DT2030170-00
Safety ducting distance - Fig. 36
When hot air is to be ducted using a Ø 3” / (Ø 75 mm) flexible pipe to
adjoning rooms the minimum lenght shall not be under 4” / (10 cm)
which corrisponds to the minimum distance allowed from the wall to
rear of the stove.
If the flexible pipes go throught combustible walls and ceilings the
minimum required clearance is 1/2” / (1,3 cm).
Such space if made by air is allowed but it is reccomended to fill this
space with insulation (e.g. mineral fibre, ceramic fibre, rock fibre)
wrapped around the flexible pipe.
COMBUSTIBLE
WALL
MINIMUM REQUIRED
CLEARANCE
1/2"
(13 mm)
FLEXIBLE
PIPE
aaThe flexible pipes are hot while in operation. If they aren’t
DT2033375-00
Fig. 37
HOT AIR OUTLET VENT
”/
.6
23
(60
)
cm
located at least 7.9” / (200 mm) from the floor.
MINIMUM LENGHT
R
aaIf the floor is flammable, the hot air outlet vents must be
4"
(102 mm)
1/2"
(13 mm)
insulated and pass through a room (typically in the space
behind the stove) keep children, clothing and furniture away.
Contact may cause skin burns.
Hot air outlet vent radiation area - Fig. 37
A safety area must be ensured around the hot air outlet vent within
which there must be no flammable objects (furniture, carpets, curtains,
etc.) or heat sensitive materials (wood, plastic, etc.).
The diagram to the side shows the measurements for this safety area,
which includes 23.6” / (600 mm) from the upper edge of the vent.
DT2030171-00
Fig. 36
23.6” / (60 cm)
English
Wall and floor ducting - Fig. 32 / 35
For efficient ducted heat distribution:
-- lag the flexible pipe with a 0.79” / (2 cm) thick insulation (e.g. mineral
fibre, ceramic fibre, rock fibre) to limit heat loss and to guarantee a
sufficiently warm air temperature;
-- the insulation must have a specifi c weight equal to or more than 50
kg/m³ with working temperature limit of at least 482°F / (250°C).
Thermal conductivity λ (100°C) ≤ 0,050 W/mK.
-- Material with code “AGI Q132” or “DIN 18895” is allowed for thermal
insulation;
-- the maximum total length of the flexible pipe connected to the fan
must not exceed 32.8’ / (10 m).
23.6” / (60 cm)
23.6” / (60 cm)
DT2030172-00
22
H07025240/DT2000723 – 01
DT2011891-00
5.2 Electrical connections and controls
Power cable (6)
•The stove/fireplace comes with a power cable which must be
connected to a 230V/50Hz mains socket. Connection to the rear of
the stove/fireplace is shown in fig. 40.
•The power rating is indicated in the paragraph “TECHNICAL DATA”.
Fig. 38
aaThe appliance must be connected to an efficient earthing/
Room sensor connection (5)
•When installing the stove/fireplace, it is necessary to connect the
room sensor (provided) to the correct jack (Fig. 38). The sensor can be
positioned as shown in fig. 39, otherwise remove the band, uncoil the
lead and then place the sensor in a spot where a more accurate room
temperature reading can be obtained.
Pipe tap (3)
•The appliance has an external socket for measuring the pressure
(vacuum) of the flue gas outlet pipe. This control and verification should
be carried out by authorised personnel at the time of installation or
during maintenance.
4
English
3
grounding system.
Ensure that in its normal position the power cable does not
come into contact with any heated parts.
Ensure that the electrical plug is accessible also after
installation of the stove.
7
2
1
1External jack for connection of
room sensor
2Socket for power lead
3Pipe tap
4Knockout for inserting cable gland
PG7 for connection of external
thermostat
Fig. 39
DT2030074-01
5Room sensor connection
6Power lead connection
7DB9 serial socket
Fig. 40
6
5
Connection to the DB9 serial socket (7)
•The appliance has a DB9 serial socket, which is used to check
appliance operation. Controls should be carried out by authorised
personnel at the time of installation or during maintenance.
•The optional GPRS kit, if ordered, may be connected to the DB9 serial
socket.
DT2032732-00
DT2030075-01
DT2010079-05
5.3 Installing the external thermostat
The appliance is designed for connection to an external room thermostat
(not included in the package).
To connect the thermostat use a 2x0.5 mm2 cable secured with a PG7
cable gland to be inserted in the relative hole in the rear panel (Fig. 43).
Only authorised personnel should carry out this operation.
Fig. 41
1
4
aaInstallation can be carried out with any type of room thermostat
but requires a PG7 cable gland similar to that shown in fig. 41.
To connect the room thermostat to the electronic board, refer
to the wiring diagram.
To install, proceed as follows:
-- cut off the electricity to the appliance before opening it;
-- remove the knockout to be found in the rear panel (position 4 – figure
38);
-- clamp the thermostat cable with the PG7 cable gland and insert the
gland into the hole in the rear panel (Fig. 43);
-- connect the thermostat terminal to the two-pin terminal of the
electronic board (Fig. 42).
2
3
DT2030076-00
1Thermostat
2Electronic board 2-pin terminal
Fig. 42
Fig. 43
DT2030077-00
H07025240/DT2000723 – 01
3Cable gland
4Thermostat cable terminal
DT2030078-01
23
DT2010123-02
5.4 Installing the Y-element (optional)
•Ducting of heat to adjoining rooms is at the user’s discretion.
Fig. 44
English
•The Y-element should be attached to the fan outlet.
•Proceed as follows:
-- disconnect from the main power supply before opening the appliance.
-- Remove the stove rear panel.
-- Uncoil the hose from the fan outlet by loosening the clip which holds
it in place (Fig. 44).
-- Cut off approx. 2” / (5 cm) hose (Fig. 45).
-- Fix the hose to the Y-element using the clip that was previously
loosened (Fig. 46).
-- Fix the Y-element to the fan outlet using the screws provided (Fig. 47).
Loosen the
hose clip
Fig. 45
DT2030182-00
Fig. 46
DT2030174 -00
Fig. 47
DT2030175-00
-- Using the hose clip provided, attach a piece of hose to the second
branch of the Y-element, of sufficient length to reach the duct
embedded in the wall (Fig. 48).
-- Remove the knockout from the rear panel (Fig. 49).
Fig. 48
DT2030176-00
Fig. 49
DT2030178-00
-- Replace the rear panel.
-- Move the stove closer to the wall (Fig. 50) and, using the hose clips
provided, fix the hose to the duct in the wall (Fig. 51).
-- Place the stove in the desired location, complying with the minimum
safety distances (see section “MINIMUM SAFETY DISTANCES”).
Fig. 50
H07025240/DT2000723 – 01
DT2030179-00
Fig. 51
DT2030180-00
24
Cutting the
hose
DT2030181-00
6.0 USE
The pellet stove is a different type of heater. Its operation and maintenance differ from the traditional wood stove. Follow these operating instructions
exactly as stated to ensure safe and reliable operation.
•Do not use the stove as a cooking appliance.
•Ensure that the room in which the stove is installed is sufficiently well ventilated (fresh air intake).
•A certain amount of carbon monoxide may be produced within the stove as a by-product of combustion. All exhaust vent connections must be
sealed with RTV silicone to assure a gas tight seal. Any leaks into a confined area caused by faulty installation or improper operation of the stove
could produce dizziness, nausea and in extreme cases, death.
•Check (or have checked) regularly that the flue is clean.
•Under no circumstances use fuels other than pellets.
•Remove any deposits of unused pellets left by failed ignition before restarting the stove.
aaDirect contact with the stove while operating may cause skin burns.
aaDuring operation some parts of the stove (door, handle, controls, ceramic parts) can reach high temperatures. Take great care and all
the necessary precautions, especially in the presence of children, the elderly or disabled and pets.
Keep any inflammable object well away from the stove while it is in use (MINIMUM 32” - 80 cm) from the front panel.
While in use the door must remain closed and the glass must be present and intact.
The removal of the protective grille inside the pellet hopper is strictly prohibited.
If replenishing with pellets while the stove is lit, ensure that the bag does not come into contact with any hot surfaces.
aaOperate this unit only with the fuel hopper lid closed. Failure to do so may result in emission of products of combustion from the
hopper under certain conditions. Maintain hopper seal in good condition.
DT2010035-06
DT2010730-00
6.1 Loading the pellets
•When lighting your stove for the first time, or any time you have run
out of Pellets, you will need to fill the hopper. Pellets are fed from
the hopper to the burn pot by an auger. A high torque motor that is
capable of doing serious harm to fingers drives the auger and for this
reason in Piazzetta pellet stoves a protective grille inside the hopper
is placed.
Fig. 52
Fig. 53
ddDon’t remove the protective grill inside the pellet hopper.
•To load the pellets into the hopper it is advisable to tear off the edge
of the sack and empty the sack directly into the hopper. This makes
filling easier and avoids pouring pellets on top of the stove.
ddDo not allow sawdust to accumulate on the bottom of the
DT2030459-00
DT2030460-00
hopper.
ddDo not leave leftover pellets on top of the stove – they could
catch fire!
ddDo not overfill hopper.
aaMaintain hopper seal in good condition.
H07025240/DT2000723 – 01
25
English
DT2012364-00
DT2011836-01
6.2 Remote control
•The pellet stove comes equipped with an LCD-display remote control
and radio transmitter which allow you to operate its various functions.
Fig. 54
English
aaThe remote’s range can be affected by other devices which
operate on a continuous radio frequency of 433.92 MHz, for
example radio headphones, toys, wireless mouses etc.
The remote has a range of around seven metres in conditions
where there is no interference from other sources.
•When pressing the keys to select the various functions wait for
a signal from the stove that the selection has registered before
selecting further functions. Or if you are in an adjoining room wait
for confirmation on the remote’s display. If the stove is not receiving
signals from the remote try bringing the remote closer to the stove.
Below are listed the various functions of the remote control’s keys.
17
15
19
20
18
13
16
2
!
14
1
1 2 3 4 5 6 7
4
6
3
7
GRUPPO
PIAZZETTA
5
8
9
10
NUMBER
1
26
KEY / DISPLAY
KEY ON/OFF
2
KEY STAND-BY
3
KEY POWER
4
KEY FAN SPEED
5
KEY SELECT
6
KEY TEMPERATURE
7
KEY TIMER
8
KEY MENU
9
10
11
KEY SET
KEY MENU SELECTION
KEY ESC
12
KEY OPT
13
14
15
DISPLAY
DISPLAY POWER
DISPLAY MULTIFUOCO
16
DISPLAY DAYS OF THE WEEK
17
18
19
20
DISPLAY RADIO SIGNAL EMISSION
DISPLAY TIMER
DISPLAY SAFETY
DISPLAY FLAT BATTERY
11
MENU
ESC
SET
OPT
12
DT2030325-00
DESCRIPTION
Allows you to start up or shut down the stove.
Pressing the stand-by key and holding it down (for around 5 seconds) until KEYPAD BLOCKED appears
on the display will disable the keypad. To re-enable the keypad press the stand-by key and hold it down
(for around 8 seconds) until KEYPAD UNBLOCKED appears on the display.
Allows you to select the power setting. With the SELECT key you can choose between the four available
settings, P1-P2-P3-P4.
Allows you to choose the speed setting on the Multifuoco fan. With the SELECT key you can choose
between the three available settings, 01-02-03.
Allows you to choose:
• power level - having previously pressed the POWER key
• fan speed - having previously pressed the FAN SPEED key
• temperature - having previously selected the TEMPERATURE key
Allows you to set the room temperature. The SELECT key will allow to choose the desired temperature
between 44°F and 86°F / (7°C and 30°C).
Displays the current date and time.
Allows:
• access to the programming menu
• return to the initial display
Confirm MENU selected
Scrolls through the programming MENU
Returns to previous menu
Displays the MULTICOMFORT temperatures. The dash before the temperature shows which sensor is
giving the temperature reading.
Shows on three lines the function settings, the current time and the temperature.
Shows the power setting selected, P1-P2-P3-P4.
Shows the Multifuoco setting selected, 01-02-03.
Shows the day of the week, 1 Monday, 2 Tuesday, 3 Wednesday, 4 Thursday, 5 Friday, 6 Saturday, 7
Sunday.
Active if the remote is receiving data from the stove
Shows that the timer is engaged
Symbol appears when the safety system is activated
Shows that the battery is flat or running down
H07025240/DT2000723 – 01
DT2010082-05
6.3 Lighting for the first time
•Carefully read this “Instructions for Installation, Use and Maintenance“ in its entirety before lighting your stove for the first time.
•Before lighting the stove for the first time, check that the grate is properly placed and pushed back towards the baffle plate.
•There will be odours when lighting the first few times due to the evaporation of paints and oils used during the manufacturing process.
To this end, follow the instructions given below when using the stove:
-- operate at medium power for the first 5-6 hours after igniting the fuel (the expansion caused by the heat during this stage will allow the stove
body to settle);
-- after the settling-down stage the stove must be set to operate at maximum power for a period between 6 and 10 hours, depending on the amount
of paint on the stove body that must be evaporated off.
The time indicated for operation at maximum power does not necessarily have to be continuous, but may be divided up into two periods separated
by an interval of at least 3-4 hours with the stove shut down.
At the end of the recommended period the paint will have evaporated and the stove should be used at the suitable power for normal use.
If necessary the stove may be used for a further period at maximum power to ensure complete and final disappearance of all paint residue.
When the hopper is being loaded for the first time the loading auger needs time to fill up; during this stage the pellets are not distributed inside the
firebox and it is highly probable that the first attempt at ignition fails. If the alarm is activated, shut down the stove by pressing the ON/OFF key for a
few moments, remove the fuel in the grate and then set the stove for a new ignition process.
DT2012169-00
6.4 Startup and normal operation
•Before proceeding with lighting the stove:
Fig. 55
aaEnsure that the hearth door is well closed.
aaNever use gasoline, gasoline-type lantern
OF F
fuel, kerosene,
charcoal lighter fluid, or similar liquids to start or ”freschen
up” a fire in this heater. Keep all such liquids well away from
the heater wihle it is in use.
aaWarning against overfiring:
-- Pellets must not be fed manually into the burn pot.
-- Never add additional fuel by hand.
-- Do not fill the hopper with any fuels other than wood pellet.
-- Accumulated un-burnt pellets in the burn pot after a failed
ignition must be removed before starting a new ignition
process.
09 : 53
68F
1
aaOperate unit only with hopper lid closed.
Failure to do so may result in emmision of products of
combustion from the hopper under certain conditions.
•Check that the pellet tank is full or at least contains enough pellets for
the stove to run for the desired period.
•When the stove is connected to the power supply but is not yet lit, the
display will show the readout OFF and in the lower half the current
time, the measured temperature and the previously set power and
fan settings.
H07025240/DT2000723 – 01
27
English
During this stage, air the room well where the stove is installed and avoid staying there any length of time since the fumes being given off could be
harmful to persons or pets.
The stove body should have settled down and the paints fully evaporated after having lit the stove a few times.
START
PHASE I
STARTUP
Action
1
Display
operating mode:
English
START
PHASE II
1
Description
1 2 : 0 0 7 3 FA cycle starts with three phases which take the stove into the normal
CONTROL (first 20 seconds)
•The lighter (glow plug) activates.
1
1 Hold
2 : the0 ON/OFF
0 7key
3F
down for several
seconds
1
1
START PHASE I
•The extractor fan starts up.
•The fuel-loading auger is activated and starts to feed pellets into the
grate.
1
1
1
START PHASE II
•If the lighter has triggered the combustion process, the fuel-loading auger
increases to allow a period of stabilisation and correct combustion of the pellets
in the subsequent normal operating mode.
•If during the startup phase the sensor on the flue gas outlet shows a rise in
temperature (sign that the combustion process is underway), the stove is
considered to be lit and goes into the normal operating mode.
1
1
1
CONTROL
CONTROL
1 2C O: 0N 0T R O
7 3L F
1 2 : 00 73F
1 2 : 00 73F
START
P HS A
T ASRE T I
AT A
S RE T7 3I F
1P
2 HS
:0
0
P H: 0A 0S E 7 3I F
12
1 2 : 00 73F
START
P HSAT A
SR
ET II
P H:S0
AT 0
SA ER 7T 3I IF
12
IF
1 2P H
: 0A 0S E 7 3I DT2040051-07
1 2 : 00 73F
NORMAL OPERATION
Action
Description
Display
Once the startup cycle has been completed successfully the stove
stabilises in the normal operating mode.
The power, fan speed and room temperature may be adjusted during
normal operation.
Shown is an example of the INITIAL DISPLAY in normal operation.
1
1
Press the
POWER
key and
select
LEVEL
P2
POWER
To adjust the power, press the POWER key and select the desired setting
by pressing the SELECT key.
After the desired setting has been selected the remote control returns to
1
the INITIAL DISPLAY.
L E1V2E: L0 0 7 3 F
P2
1
1
LEVEL
P2
1 2 : 00 73F
SE T
POWER
P3
1 2 : 00 73F
1
28
SE T
POWER
H07025240/DT2000723 – 01
SE T
Press the
FAN key
and
select
Description
1
1
LEVEL
FAN SPEED
P2
To adjust the Multifuoco setting, press the FAN key and select the desired
L E V E L 1 2 : 00 73F
P2
Multifuoco setting using the SELECT key.
1
Press the
TEMPERATURE
key and
select
1 2 : 00 73F L E V E L
P2
SE T
1 2 P: 0O 0W E 7R 3 F
1
ROOM TEMPERATURE
To adjust the temperature setting, press the TEMPERATURE key and select
the desired temperature by using the SELECT key (range 44°F to 86°F).
When the desired temperature has been reached the readout OK appears
1
in the initial display and the stove operates
at minimum power even if the
display shows the originally set power level. The temperature can be read
by the remote control, by the stove itself or by an external thermostat. To
1
choose whether the remote or the stove will read the temperature see the
paragraph “MULTICOMFORT”.
If using an external thermostat the readout “ton” appears in the initial
display and the
readings from the stove and the remote control are cut out.
1
SE T
L EO VW EE R
L
P
P2
P3
1 2 : 00 73F
1
1
1
P3
SE T
P O W Efunction
R activates
During normal operation the automatic grate cleaning
SE T
periodically, the frequency varying according to the settings preP3
programmed by Gruppo Piazzetta personnel.V E N T - 1
1
1
1
Display
SE T
SE T
VENT - 1
VENT - 1
02
02
English
1
Action
POWER
POWER
P3
P3
SE T T EMP
SE T T EMP
ROOM
ROOM
79F
79F
1
1
This operation removes ash deposits and other buildups, which would
otherwise prevent correct stove operation.
1
The readout “PUL” appears in STOVE
STATUS along with the flue gas
temperature.
See the PROGRAMMING section.
SE T
V ESNE TT - 1
POWER
02
P3
02
SE T
VENT - 1
SE T T EMP
If the temperature rises above a fixed value during normal stove operation at
0speed
2 and the stove runs
OOM
maximum power, the fan motor operates atRmaximum
1
1
1
1
CLEANING
CLEANING
GRATE
GRATE
1 2 : 00 79F
1 2 : 00 79F
1
1
at reduced heat input for a few minutes to help disperse the heat and prevent the
appliance from possibly overheating.
79F
SE T T EMP
R O OSME T
VENT - 1
7 9SFE T T E M P
02
ROOM
CLEANING
GSHUTDOWN
RATE 79F
1
1
1
1
1
DT2040122-00
1
C L E AAction
NING
BRAZIER
1
1
MAX VENT
MAX VENT
FLUE COOL
FLUE COOL
1 2 : 00 79F
1 2 : 00 79F
C L E A N I Description
NG1 2 : 00 79F
GS RE AT T ET E M P
Hold the ON/OFF key .
R Owhile
O Mthe cooling fan and the extractor fan continue to
1 2down
: 0for0several
2 2 c Fuel loading stops,
1
2
:
0
7 9CFL E A N I N G
operate
until
the
stove
has0
cooled.
seconds
79F
G R A Talong
E
•The readout “PUL” appears in STOVE
M ASTATUS
X V E NwithT the flue gas
temperature.
2U: E0 0C O7O9LF
•See the section on programming. F1 L
Display
1
CLEANING
GRATE
1
1
1
1
1 2 : 00 73F
AX VENT 1 2 : 00 79F
aaNever unplug the stove from theCMpower
L E supply
A N IatNthisG stage as this could cause internal problems and compromise subsequent
FLUE COOL
GRATE
1 2 : 0 0 7 9MFA X V E N T
1 2 : 00 79F
F L U E C– 01O O L
H07025240/DT2000723
1
ignition operations. 1
1
1 2 : 00 79F
DT2040060-05
29
EXTERNAL THERMOSTAT
Action
Description
Display
Stove operation can be regulated by any kind of external room thermostat
connected to the electronic board.
To connect the thermostat, see paragraph “INSTALLING THE EXTERNAL
ROOM THERMOSTAT”.
English
Operation of the external thermostat depends on the stove temperature
setting.
•If the set stove temperature is less than the room temperature, the
external thermostat prevails. (It is advisable to set a minimum value of
44°F / (7°C) for the stove).
•If the set stove temperature is more than the room temperature, the
internal stove thermostat prevails. The external thermostat is disabled.
aaThe room sensor must be connected. If the room sensor is not
connected the appliance does not modulate the power and
operates to user settings.
DT2040059-06
DT2012309-00
6.5 Troubleshooting
A list of situations that could occur and instructions on what to do is given below.
FAILED IGNITION
Action
Description
Display
!
NO
LIT
If the readout NO LIT appears on the display during the startup stage and
the buzzer activates (if set), it means that the sensor installed on the flue
gas outlet detects no temperature rise (sign that the combustion process
has not been triggered) or the pellet hopper is empty. The stove goes into
the alarm status.
1
1 2 : 00 73F
DT2040056-06
30
H07025240/DT2000723 – 01
FAILED IGNITION: WHAT TO DO
Description
Display
Shut the stove down
.c
by pressing the
•The warning buzzer stops.
ON/OFF key down for •The readout CLEANING GRATE appears on the display and when the
a few seconds
stove has cooled the readout OFF appears.
•Check the cause of failed ignition and why the safety device has
activated. Always remove any fuel from the grate before starting a new
ignition process.
1 2 : 00 22
1
CLEANING
BRAZIER
CLEANING
GRATE
1
1 2 : 00 73F
English
CLEANING
Action
BRAZIER
.
Restart
12
: 0the0stove2by2 c
pressing the ON/OFF
1
key
•Repeat the ignition process as described above.
aaIf the stove occasionally fails to ignite it could be caused by:
-pellet composition or size not in compliance with the specifications given in this booklet (see the “FUEL” section);
-insufficient mains voltage, whether in the form of intermittent voltage drops or a constantly lower value.
In the above cases any call-out of the service centre is not covered by the warranty, since the problem is not due to a defect in the
DT2040057-07
product. WAIT FOR START UP
Action
The user attempts
to restart the stove
during the shutdown
stage when the
stove is still hot by
pressing the ON/
OFF key for a few
moments
WAIT FOR
START UP
1
1 2 : 00 73F
Description
If the readout “WAIT FOR START UP” appears on the display by pressing
the ON/OFF key for a few moments, it means that the stove is still hot and
it is necessary to wait for it to cool.
The new ignition cycle will be inhibited until the stove ends the cooling
phase.
After waiting for a few minutes the user can restart the stove and a new
ignition cycle will start automatically from the control stage.
Display
WAIT FOR
START UP
1
1 2 : 00 73F
DT2040123-00
H07025240/DT2000723 – 01
31
INTERRUPTION OF POWER SUPPLY
Action
Description
Display
If there is a blackout while the stove is in operation, there are two
possibilities of procedure according to stove set-up:
-- blackout without timer thermostat settings.
-- blackout with timer thermostat settings.
English
Blackout without timer thermostat settings.
When the electricity supply is restored, the appliance restarts automatically.
•The grate cleaning phase activates.
•The fan operates at full speed to allow the stove to cool.
•The automatic stove restart cycle starts (the steps detailed in the
‘STARTUP’ phase are repeated automatically).
•Once the ignition cycle has been completed the stove operates normally
at power level 2 with Multifuoco on 2.
Blackout with timer thermostat settings.
There are 3 possible situations.
-- Blackout straddling the time set for ignition: the stove does not restart.
-- Blackout straddling the time set for shutdown: the stove restarts when
the electricity supply is restored.
-- Blackout within the programmed operating time band: the stove restarts
when the electricity supply is restored.
Restarting is carried out with the same procedure as listed in “Blackout
without timer thermostat settings”.
CLEANING
1 2 : 00 73F
1
DT2040061-05
EMERGENCY LIGHTING OF STOVE
Action
Description
Display
If the glow plug is not working, the stove may be lit manually as follows:
-- pour a small quantity of pellets into the grate;
-- use a lit piece of solid firelighter (not liquid) to ignite the pellets;
-- close the door;
-- start the stove using the ON/OFF button.
aaThis procedure is only to be carried out in an emergency while waiting for the servicing technician to arrive. 32
H07025240/DT2000723 – 01
DT2040098-00
DT2010222-07
6.6 Control panel
The stove is fitted with a digital control panel to operate stove functions
when the LCD remote control is unavailable.
The various functions of the control panel are listed below.
Fig. 56
2
1
3
8
7
4
3
6
English
2
5
1
DT2030332-00
NUMBER
KEY / DISPLAY
DESCRIPTION
1
Key ON/OFF
Allows you to start up or shut down the product manually.
2
ON/OFF Led
If the LED lights up, it indicates that the stove is lit.
3
Key INCREASE POWER
Allows you to increase the power setting. You can choose between the two available settings, P1-P3. The
Multifuoco fan has a default setting for each of the two power settings.
4
INCREASE POWER Led
The LED lights up when the power-increase key is pressed and indicates that the power has been increased.
5
Key DECREASE POWER
Allows you to decrease the power setting. You can choose between the two available settings, P1-P3. The
Multifuoco fan has a default setting for each of the two power settings.
6
DECREASE POWER Led
The LED lights up when the power-decrease key is pressed and indicates that the power has been decreased.
7
SAFETY DEVICE Led
If the LED lights up, it indicates that a safety device has activated. After approx. 60 seconds the alarm signal will
sound (if activated). In the event of activation proceed as follows:
-- turn off the stove by pressing the ON/OFF key for several seconds;
-- the alarm signal will stop;
-- wait until you are sure that combustion of any pellets left in the grate has ceased;
-- wait for the stove to cool, then check for and remove whatever has activated the safety device. Finally, after
having cleaned the grate, restart the stove by pressing the ON/OFF key.
8
RADIO SIGNAL EMISSION Led
The led lights up when the stove receives data from the remote control.
DT2010469-04
6.7 Setting the language
This function allows one of the four languages available to be set on the display according to the country where the product is installed.
HOW TO SET THE LANGUAGE
Function
Selecting the
language menu
Action
Press the MENU button, use the MENU SELECTION button to select the
language selection menu and the SET button to confirm.
Display
SELECT
LANGUAGE
11
1
Selecting the
language
Scroll with the MENU SELECTION button to find the required language (e.g.
ENGLISH LANGUAGE) and confirm with the SET button.
LANGUAGE
ENGLISH
11
1
After confirmation the readout ENABLED FUNCTION appears on the
display, which then automatically returns to the initial readout.
FUNCTION
ENABLED
11
1
H07025240/DT2000723 – 01
33
DT2011867-01
6.8 Programming
The remote control can be used to select the following functions from the main MENU:
• SELECT LANGUAGE
SET
LANGUAGE ENGLISH
LANGUAGE ITALIANO
LANGUAGE DEUTSCH
LANGUAGE FRANCAIS
English
Remote control
MENU
ESC
SET
OPT
• UNIT OF MEASUREM
SET
F
C
SET
• SET CLOCK
DAY MONDAY
DAY TUESDAY
DAY WEDNESDAY
DAY THURSDAY
DAY FRIDAY
DAY SATURDAY
DAY SUNDAY
• SET CHRONO
SET
PROGRAM DAY
PROGRAM WEEK
PROGRAM WEEK-END
• MULTICOMFORT
SET
MENU
SELECT RRC
SELECT STOVE
• ENERGY SAVING
SET
START
STOP
• MENU PARAMETER
SET
SETTINGS FACTORY
DATA BANK
SETTINGS LOAD
SETTINGS SMOKE EXT
MULTIFUOCO V1
RESET PARTHOUR
RESET ALARM
MEMORY COUNTERS
> key access
> key access
> key access
> key access
> key access
> key access
> key access
SET
HOURS TOTAL
HOURS PARTIAL
NUMBER START
“LAST 5 ALARMS”
• ENABLE BEEP
SET
MODE BEEP - ON ÷ OFF
• STATE STOVE
• ESC
These functions are activated by opening the front flap and pressing the following keys:
-- the MENU key is used to access the main menu and return to the initial display at any time during programming to alter data that has been input
incorrectly;
-- the MENU SELECT key is used to scroll through the main menu and the submenus;
-- the SET key is used to confirm a MENU or a selection;
-- the ESC is used to return to the previous menu display at any time during programming to alter data that has been input incorrectly.
•Whenever the keypad is not used for about 3 ½ minutes, the display goes dark to reduce consumption.
•In a blackout and therefore with no reception by the stove, the display goes dark after about 20 seconds.
34
H07025240/DT2000723 – 01
DT2011296-00
6.9 Setting unit of temperature measurement
This function allows the unit of temperature measurement in CELSIUS or in FAHRENHEIT to be set on the display.
Function
Selecting the UNIT OF
MEASUREM menu
Action
Press the MENU button, use the MENU SELECTION button to select the
UNIT OF MEASUREM menu and the SET button to confirm.
UNIT OF
Display
M EU AN SI TU O
R FE M
MEASUREM
UNIT OF
MEASUREM
English
UNIT OF MEASUREMENT
1
1
1
Selecting the unit
of temperature
measurement
Scroll with the MENU SELECTION button to find the required unit of
temperature (F - Fahrenheit o C - Celsius) and confirm with the SET button.
UNIT OF
M EU AN SI TU O
R FE M
M E A SFU R E M
UNIT OF
M E A SFU R E M
F
1
1
1
FUNCTION
FE UN NA CBTLI EO DN
After confirmation the readout FUNCTION ENABLED appears on the
display, which then automatically returns to the initial readout.
1
1
ENABLED
FUNCTION
DT2040064-03
ENABLED
1
H07025240/DT2000723 – 01
35
DT2011296-00
6.10Programming the clock
The stove leaves the factory with the clock already set. All that needs to be done, therefore, is to check that the time is precise or if any change is
needed because of summer time.
Correct time setting is necessary to be able to use all the functions where time is involved.
Setting the clock entails programming the following values: day, hour and minutes.
These values are displayed in sequence upon pressing the SELECTOR key.
English
SET CLOCK (current day/time)
Function
Set the day
Action
Display
S
SE
E TT
C
C LL O
OC
CK
K
Press the MENU key, select the SET CLOCK menu using the SELECT MENU
key, then confirm by pressing the SET key.
11
11
Confirm setting and
move to next section
DA
AY
Y
D
MO
ON
ND
DA
AY
Y
M
Press the SELECT MENU key and set the “DAY”.
Confirm by pressing the SET key.
11
11
Set the hour
Press the SELECT MENU key and set the current “HOUR”. Confirm by
pressing the SET key.
11
11
Set the minutes
Press the SELECT MENU key and set the “MINUTES”. Confirm by pressing
the SET key. After confirmation the initial display will reappear.
11
11
HO
OU
UR
RS
S
H
CLOCK
12:
M
M II N
NU
U TT E
ES
S
C
C LL O
OC
CK
K
:: 0
0 11
DT2040064-03
36
H07025240/DT2000723 – 01
DT2010242-05
6.11Timer
The timer allows the user to programme the stove to start up and shut down automatically without any manual intervention.
Daily, weekly and weekend programmes can be selected with a maximum of two operating cycles in two separate timetable bands.
For example:
Cycle 1: from 6am until 9am.
Cycle 2: from 8.30pm until 11pm.
For example:
English
•In the DAILY programme the two timetable bands once established can be activated or deactivated for all the days of the week.
if you want the stove to operate from 6am to 9am every day
•In the WEEKLY programme the two timetable bands once established can be activated or deactivated for each day.
For example:
if you want the stove to operate from 6am to 9am on Monday, Tuesday, but not on Wednesday, and so on.
•In the WEEKEND programme the two timetable bands once established can be activated or deactivated for Friday, Saturday and Sunday.
For example:
if you want the stove to operate from 6am to 9am on Friday, Saturday, but not on Sunday.
This kind of timer allows you to have three programmes (DAILY, WEEKLY and WEEKEND) stored permanently. The programmes can be activated or
deactivated using the SET TIMER menu. It is advisable to have only one programme active at a time to avoid overlapping.
aaWHEN USING THE TIMER FOR THE FIRST TIME, SET THE CLOCK WITH THE CURRENT DAY, HOUR AND MINUTES, as with a new watch. To
set the actual time, see the table SETTING THE CLOCK. This setting will only be necessary the first time of activating the clock.
DAY PROGRAMME - 1st operating cycle
Function
Select set chrono
menu
Action
Display
S
SE
E TT
C
CH
HR
RO
ON
NO
O
Press the MENU key. Using the SELECT MENU key select the SET CHRONO
menu and confirm by pressing the SET key.
1
1
Select day
programme
P
PR
RO
OG
GR
RA
AM
M
DA
D
AY
Y
Using the SELECT MENU key select the day-programme “PROGRAM DAY”
menu and confirm by pressing the SET key.
1
1
Enable or disable day
programme
Press the SELECT MENU key and select ON to enable the day programme
or OFF to disable the day programme. Confirm by pressing the SET key.
If you have disabled the programme by selecting OFF and do not wish to
carry out further programming, press the ESC (EXIT) key to return to the
previous menu or the MENU key to return to the initial display.
1
1
Set startup time for
1st operating cycle
SE T
CHRONO
S T AR T
D
PROGRAM 1
Press SELECT MENU to set the startup time, advancing in ten-minute
jumps (for example, you want the stove to start up at 06:00). Confirm by
pressing the SET key.
1
1
E
EN
NA
AB
B LL E
E
D
DA
AY
Y
O
O FF FF
06 : 00
37
H07025240/DT2000723 – 01
PROGRAM
S T OP
D
CHRONO
Function
11
Action
11
PROGRAM
DAY
English
Press SELECT MENU to set the shutdown time, advancing in ten-minute
jumps (for example, you want the stove to shut down at 09:00). Confirm
by pressing the SET key.
Set shutdown time
for 1st operating cycle
11
11
ENABLE
DAY
OFF
In this stage a shutdown time need not be set. Press SELECT MENU, set
the readout "OFF" and confirm by pressing the SET key.
11
Set desired power for
first operating cycle
11
Press SELECT MENU to set the desired power (for example you want
power setting 1). Confirm by pressing the SET key.
11
Set room temperature
for first operating
cycle
Press SELECT MENU to set the desired room temperature (for example,
you want a room temperature of 25°C). Confirm by pressing the SET key.
When the desired temperature has been reached the stove automatically
reverts to power setting P1 and the temperature can be read on the remote
or on the stove - see Multicomfort menu.
11
Set desired
Multifuoco fan speed
for first operating
cycle
Press SELECT MENU to set the desired fan speed (for example, you want
fan speed setting 1). Confirm by pressing the SET key.
11
After having programmed the first operating cycle you may, if you wish, proceed with
programming the second operating cycle by going through the settings in the order as
described above. The number 2 appears on the display to indicate the second operating cycle.
11
PROGRAM
06 : 00
1
Display
S T OP
D
PROGRAM 1
09 : 00
S T OP
D
PROGRAM 1
OFF
SE T
PO W ER
01
D
1
SE T T EMP
ROOM
1
77F
SE T
VENT - 1
01
D
S T AR T
D
PROGRAM 2
20 : 30
DT2040067-03
38
H07025240/DT2000723 – 01
WEEK PROGRAMME
Select set chrono
menu
Action
Display
S
E
TT
S
E
S
E
TT
S
E
S
E
TT O
C
H
R
N
O
S
ER
C
H
O
N
O
C
H
R
O
N
O
C
H
R
O
N
C
H
R
O
N
O
CHRONO
O
Press the MENU key. Using the SELECT MENU key select the SET CHRONO
menu and confirm by pressing the SET key.
English
Function
1
1
1
1
1
1
1
Select week
programme
P
R
O
G
R
A
M
P
R
O
G
R
A
M
P
R
O
G
R
A
M
P
R
O
G
R
A
P
R
O
G
R
A
M
W
E
E
K
PR
OK
GRAM
M
W
E
E
W
E
E
K
W
E
E
K
W
WE
EE
EK
K
Using the SELECT MENU key select the week-programme “PROGRAM
WEEK” menu and confirm by pressing the SET key.
1
1
1
1
1
1
1
Enable or disable the
week programme
Press the SELECT MENU key and select ON to enable the week programme
or OFF to disable the week programme. Confirm by pressing the SET key.
If you have disabled the programme by selecting OFF and do not wish to
carry out further programming, press the ESC (EXIT) key to return to the
previous menu or the MENU key to return to the initial display.
1
1
1
1
1
1
1
Set startup time for
1st operating cycle
Press SELECT MENU to set the startup time, advancing in ten-minute
jumps (for example, you want the stove to start up at 06:00). Confirm by
pressing the SET key.
1
1
1
1
1
1
1
Press SELECT MENU to set the shutdown time, advancing in ten-minute
jumps (for example, you want the stove to shut down at 09:00). Confirm
by pressing the SET key.
1
1
1
1
1
1
1
Set shutdown time
for 1st operating cycle
In this stage a shutdown time need not be set. Press SELECT MENU, set the
readout OFF and confirm by pressing the SET key.
1
1
1
1
1
1
1
Activate or deactivate
the first operating
cycle on individual
days of the week
Press the top part of the SELECT MENU key to select the day of the week,
then press the bottom part of the SELECT MENU key to select ON to
activate the first operating cycle on the chosen day or OFF to deactivate
the first operating cycle on the chosen day. Active days will be shown on
the DAYS OF THE WEEK display by the digits 1 MO - 2 Tu - 3 WE - 4 TH 5 Fr - 6 SA - 7 Su. Confirm by pressing the SET key.
H07025240/DT2000723 – 01
EN
NA
AB
B LL E
E
E
E
N
A
B
L
E
N
B
LLL E
E
N
A
B
E
WE
EE
EA
K
E
N
A
B
E
W
E
K
W
E
E
K
W
E
E
K
W
WE
EFF E
EFF K
K
O
O
O
F
F
O
O
O FFF FFF
S TT A
AR
R TT
S
S
T
A
R
TT
S
TTT A
R
S
A
R
P
R
O
G
R
AM
M
S
A
R
TT A
P
R
O
G
R
P
R
O
G
R
A
M
P
R
G
R
P
R
O
G
R
A
M
P6
RO
O:: 0
G0
RA
AM
M
0
6
0
0
0
0
6
:
0
0
0
0
6
0
0
06
6 ::: 0
00
0
W
W
W
W
W11
W
11
11
S TT O
OP
P
S
S
T
O
P
S
P
S
O
P
PR
RTTT O
GR
RA
AM
M
S
O
P
P
G
P
R
O
G
R
A
M
P
R
G
R
P
R
O
G
R
A
M
P9
RO
O:: 0
G0
RA
AM
M
0
9
0
0
0
0
9
:
0
0
0
0
9
0
0
09
9 ::: 0
00
0
W
W
W
W
W
W111
111
S TT O
OP
P
S
S
T
O
P
S
P
S
O
P
P
RTTT O
GR
RA
AM
M
S
O
P
P
R
G
P
R
O
G
R
A
M
P
R
O
G
R
A
M
P
R
O
G
R
A
M
P
R
O
G
R
A
M
O
F
F
O
FF FF
O
O
O
O FFF FFF
W
W
W
W
W
W111
111
DA
A
D
D
A
D
A
D
DA
A
SU
U
S
S
U
SU
U
S
S
U
Y
Y
Y
Y
Y
Y
S
S
S
S
S
S
7
7
77
7
7
7
W
W
W
W
W
W
ON
N
O
O
N
ON
N
O
O
N
39
Function
Action
Display
Set desired power for
first operating cycle
Press SELECT MENU to set the desired power (for example you want
power setting 1). Confirm by pressing the SET key.
SE T
CHRONO
11
English
11
Set room temperature
for first operating
cycle
PROGRAM
WEEK
Press SELECT MENU to set the desired room temperature (for example,
you want a room temperature of 25°C). Confirm by pressing the SET key.
When the desired temperature has been reached the stove automatically
reverts to power setting P1 and the temperature can be read on the remote
or on the stove - see Multicomfort menu.
11
Set desired
Multifuoco fan speed
for first operating
cycle
11
ENABLE
WEEK
OFF
Press SELECT MENU to set the desired fan speed (for example, you want
fan speed setting 1). Confirm by pressing the SET key.
11
11
S T AR T
W
After having programmed the first operating cycle
youOmay,
PR
G Rif AyouM wish,1 proceed with
programming the second operating cycle by going through the settings in the order as
described above. The number 2 appears on the display to indicate the second operating cycle.
06 : 00
11
11
SE T
PO W E R
01
W
1
SE T T EMP
ROOM
77F
SE T
VENT - 1
01
W
SE T
W
PROGRAM 2
20 : 30
DT2040068-03
11
11
S T OP
W
PROGRAM 1
09 : 00
S T OP
W
PROGRAM 1
OFF
DAYS
SU
40
77
W
ON
H07025240/DT2000723 – 01
WEEKEND PROGRAMME
Select set chrono
menu
Action
Display
SE
E TT
S
CH
HR
RO
ON
NO
O
C
Press the MENU key. Using the SELECT MENU key select the SET CHRONO
menu and confirm by pressing the SET key.
English
Function
1
1
Select weekendprogramme
P
PR
RO
OG
GR
RA
AM
M
W
WE
EE
EK
K -- E
EN
ND
D
Using the SELECT MENU key select the “PROGRAM WEEK-END”
weekend-programme menu and confirm by pressing the SET key.
1
1
Enable or disable
weekend programme
Press the SELECT MENU key and select ON to enable the weekend
programme or OFF to disable the weekend programme. Confirm by
pressing the SET key. If you have disabled the programme by selecting
OFF and do not wish to carry out further programming, press the ESC
key to return to the previous menu or the MENU key to return to the initial
display.
1
S
E TT
S
SE
ET
C
H
RO
NO
C
CH
HR
RO
ON
NO
O
1
11
Set startup time for
1st operating cycle
1
1
11
P
RO
GR
AM
P
PR
RO
OG
GR
RA
AM
M
W
E
E
K
E
N
D
W
WE
EE
EK
K -- E
EN
ND
D
Press SELECT MENU to set the startup time, advancing in ten-minute
jumps (for example, you want to stove to start up at 06:00). Confirm by
pressing the SET key.
1
1
11
1
1
11
Press SELECT MENU to set the shutdown time, advancing in ten-minute
jumps (for example, you want to stove to shut down at 09:00). Confirm by
pressing the SET key.
1
1
11
Set shutdown time
for 1st operating cycle
In this stage a shutdown time need not be set. Press SELECT MENU, set
the readout OFF and confirm by pressing the SET key.
1
1
11
Activate or deactivate
the first operating
cycle on Friday,
Saturday and Sunday
Press the top part of the SELECT MENU key to select the day of the week,
then press the bottom part of the SELECT MENU key to select ON to
activate the first operating cycle on the chosen day or OFF to deactivate
the first operating cycle on the chosen day. Do this for Friday, Saturday and
Sunday (active days will be shown on the DAYS OF THE WEEK display) and
confirm by pressing the SET key.
E
NA
B LL E
E
EN
NA
AB
BLE
E
W
E
E
K
EN
D
W
WE
EE
EK
K E
EN
ND
D
O
F
F
O
O FF FF
S T AR
RT
WE
E
S
W
S TT A
A R TT
W
E
PR
RO
OG
GR
RA
AM
M 11
P
P
RO
GR
AM
1
06
6:0
00
0
0
0
6 :: 0
0
S
W
S TTT O
OP
P
WE
E
S
O
P
W
E
P
1
PR
RO
OG
GR
RA
AM
M
P
R
O
G
R
A
M 11
09
9 : 00
0
0
0 9 :: 0
00
S T OP
P
WE
S
W
S TT O
OP
WE
E
P
R
O
G
R
A
M
1
P
PR
RO
OG
GR
RA
AM
M 11
O FF FF
O
O
FF
D
DA
AY
YS
S
D
A
Y
S
LL II TT
LIT
S
SU
U
S
U
7
77
7
W
WE
E
W
E
11
1
O
ON
N
O
N
41
H07025240/DT2000723 – 01
SE T
WE
LL II TT
S
SU
U
Function
Action
Set desired power for
first operating cycle
Press SELECT MENU to set the desired power (for example you want
power setting 1). Confirm by pressing the SET key.
Display
English
1
1
Set room temperature
for first operating
cycle
Press SELECT MENU to set the desired room temperature (for example,
you want a room temperature of 25°C). Confirm by pressing the SET key.
When the desired temperature has been reached the stove automatically
reverts to power setting P1 and the temperature can be read on the remote
or on the stove - see Multicomfort menu.
1
1
SE T
CHRONO
Set desired
Multifuoco fan speed
for first operating
cycle
ENABLE
WEEK END
OFF
Press SELECT MENU to set the desired fan speed (for example, you want
fan speed setting 1). Confirm by pressing the SET key.
11
11
PROGRAM
WEEK- END
S T AR T
WE
PROGRAM 1
06 : 00
11
After having programmed the first operating cycle you may, if you wish, proceed with
programming the second operating cycle by going through the settings in the order as
described above. The number 2 appears on the display to indicate the second operating cycle.
11
11
7
7
11
O
ON
N
11
S
SE
E TT
PO
OW
WE
ER
R
P
0 11
0
WE
E
W
11
S
SE
E TT TT E
EM
MP
P
R
11
RO
OO
OM
M
7
77
7 FF
SE T
VENT - 1
01
WE
S T AR T
WE
PROGRAM 2
20 : 30
DT2040073-03
11
11
S T OP
WE
PROGRAM 1
09 : 00
S T OP
WE
PROGRAM 1
OFF
DAYS
LIT
SU
77
42
WE
1
ON
H07025240/DT2000723 – 01
SE T
WE
DT2010251-03
6.12Multicomfort
Example: your stove is installed in a small room and you are ducting the heat only from the rear of the stove (see solution 1 under the paragraph
“MULTIFUOCO SYSTEM”). You can position the remote control in the room to where the hot air has been ducted and set the required temperature
from this room. To carry out the necessary settings see the MULTICOMFORT menu.
MULTICOMFORT
This function is used to choose the sensor for reading the room temperature: from the stove or from the remote control. To make the
most of the Multifuoco fan functions read the paragraphs MULTIFUOCO SYSTEM and MULTICOMFORT OPERATION.
Function
Select the
MULTICOMFORT
menu
Action
Display
MUL T I
COMFORT
Press the MENU key, then using the SELECT MENU key select the
MULTICOMFORT menu.
Confirm by pressing the SET key.
11
SELECT
RRC
Select the REMOTE
CONTROL SENSOR
(SELECT RRC) or
STOVE (SELECT
STOVE)
Press the SELECT MENU key and select “SELECT RRC” to read the room
temperature from the remote control or “SELECT STOVE” to read the
room temperature from the stove. Confirm by pressing the SET key. After
confirmation the readout function enabled (FUNCTION ENGAGED) will
appear on the display and the remote control will automatically return to
the initial display.
11
SELECT
STOVE
11
DT2040070-04
DT2012431-00
6.13Energy Saving
When the ENERGY SAVING mode is enabled, automatic startup/ignition and shutdown of the stove is activated at temperature values set by the user
through the STOP and START functions.
The temperature value selected 2, 4 or 6 °F (1, 2 or 3 °C ) in STOP function or selected in START function with negative values -2, -4 or -6 °F (-1, -2
or -3 °C) defines the value from which the Energy Saving mode will either increment or deduct from the room temperature set.
The operating principle is as follows:
when the room temperature measured by the room sensor, the remote control or the external thermostat reaches the temperature value programmed
by the user, the stove automatically goes to power level 1 (readout “OK” on the display).
If the room temperature continues to rise with operation at power level 1 up to the value set on the STOP function (e.g. +4 °F / +2 °C compared to
the programmed temperature), the stove shuts down and goes into the stand-by mode.
When the room temperature measured by the room sensor, the remote control or the external thermostat drops to the temperature value set by the
user on the START function (e.g. -6 °F / -3 °C compared to the programmed temperature), the stoves starts a new ignition phase and goes back to
H07025240/DT2000723 – 01
43
English
The pellet stove is fitted with the Multicomfort function. This works in conjunction with the Multifuoco ventilation system to improve heat distribution.
It allows the room temperature to be read from the stove or from the remote control, so that the Multifuoco settings can be varied according to the
requirements of the rooms to be heated.
If the airflow from your stove has been ducted to other rooms you may read the temperature in the room where the stove is installed or in the room
where the remote control is situated.
the power level previously set by the user.
aaThe stove only restarts when the temperatures measured on the actual stove allow its use in all safety.
If the STOP and OFF functions are enabled, upon reaching the programmed room temperature, the stove will operate in the conventional way by
going to power level 1 without shutting down.
Likewise with the START and OFF enabled the stove does not start the startup/ignition phase after automatic shutdown and will remain off.
ENERGY SAVING
English
Function
Select the ENERGY
SAVING menu
Action
Display
E
EN
NE
ER
RG
GY
Y
ENERGY
S
A EV RI NGGY
EN
SAVING
SAVING
Press the MENU key, then using the SELECT MENU key select the ENERGY
SAVING function and confirm by pressing the SET key.
111
1
1
Select the value to
be set for shutdown
temperature
STOP
STOP
STOP
Press the SELECT MENU key and then select the temperature set point 2,
4 or 6 °F (1, 2 or 3 °C) or disable the function by selecting OFF.
Confirm by pressing the SET key.
11
1
1
1
Select the value to
be set for ignition
temperature
Press the SELECT MENU key and then select the temperature set point 2,
4 or 6 °F (1, 2 or 3 °C) or disable the function by selecting OFF.
Confirm by pressing the SET key.
111
1
1
After confirmation using the SET key, the readout FUNTION ENABLED is
displayed and the readout ENS (ENERGY SAVING) appears on the main
display.
111
1
1
Upon reaching the temperature set in the STOP function, the stove starts
the shutdown stage.
The readout ENERGY SAVING OK appears on the display.
11
1
1
1
44
H07025240/DT2000723 – 01
2F
2F
2F
START
START
START
O
O FF FF
OFF
OFF
LL E
EV
VE
E LL
L
E
V
EL
E
EN
NL S
SE VP
PE2
2L
ENS P2
E1 N2S: 0P02
1 2 : 00
1 2 : 00
73F
73F
73F
ENERGY
ENERGY
S
A EV RI NGGY
EN
SAVING
S11 A2
2 V:: I0
0N0
0G
1 2 : 00
1 2 : 00
OK
OK
O7
3
7K
3 FF
73F
7 3DT2040124-00
F
DT2011866-00
6.14Parameter menu
The User can only interact with the TIME METER STORAGE in the parameter menu, as described in the table below: the other parameters can only
be used by an authorised service centre.
HOUR COUNTER MEMORY
Selection of
parameter menu
Action
Press the MENU key. Using the SELECT MENU key select the MENU
PARAMETER menu and confirm by pressing the SET key.
1
1
1
Display
M
E
N
U
MENU
M
EN
UMETER
P
A
R
A
M
EN
UMETER
P
A
R
A
MA
EN
UMETER
P
R
A
M
EN
UMETER
PA
RA
PARAMETER
PARAMETER
English
Function
1
1
1
Selection of hour
counter memory
Press the SELECT MENU key and scroll through the menu until the readout
MEMORY COUNTERS appears.
1
Confirm by pressing the SET key.
1
1
M
ME
EM
MO
OR
RY
Y
M
E
M
O
R
YR S
C
O
M
EU
MN
O TTRE
Y S
C
O
U
N
E
M
EU
MN
O TREYR
C
O
S
M
MN
O TREYR
C OE U
RS
COUNTERS
COUNTERS
1
1
1
Selection of total
hours
The readout HOURS TOTAL appears in the central part of the display and
the total hours of operation on the bottom line.
Press the SELECT MENU key.
1
1
1
1
1
1
Selection of partial
hours
The readout HOURS PARTIAL appears in the central part of the display
and the number of partial hours of operation on the bottom line.
Press the SELECT MENU key.
1
1
1
1
1
1
Selection of number
of starts
The readout NUMBER START appears in the central part of the display and
the number of ignitions on the bottom line.
Press the SELECT MENU key.
1
1
1
1
1
Selection of last 5
alarms
The last 5 alarms (e.g. NO LIT, SAFETY THERMAL, SAFETY SMOKE, ….)
appear in the central part of the display and the order in which the alarms
occurred on the bottom line.
1
Press the ESC key to return to the initial display.
1
1
1
1
1
1
H07025240/DT2000723 – 01
H
HO
OU
UR
RS
S
H
OTUARLS
TH
O
RLS
TH OO
TU
UA
RS
TH OO
T
A
OT0
UA0RLL0S
T0 O0
T0 O0 T0A0L0
T O0 T0A0L0
0
00000
00000
00000
H
HO
OU
UR
RS
S
H
OR
U TRISA L
P
A
H
OR
U TRISA L
P
HA
OR
U TRISA L
P
A
H
O0
U TRI0SA L
P0
A
R
0
P0
A0
R0
T I0A L
0
P0
A0
R0
T I0A L
0
0
00000
00000
00000
N
NU
UM
MB
BE
ER
R
N
U
M
B
E
R
S
TTUA
N
MR
BTTE R
S
A
R
N
R
S
TU
AM
RB
TE
N
U
M
B
E
R
S
T
A
R
T
0
0
0
0
0
S
T
A
R
T
0
0000
S
0 T0 A0 R0 T0
00000
00000
00000
N
NO
O
N
OT
LN
I
LN IO
T
LN IO
T
O
LM IETM - A L
LM IETM - A L
L IETM - A L
M
MEM - AL
MEM - AL
MEM - AL
-- 11
- DT2040100-00
1
- 1
- 1
- 1
45
DT2010248-04
6.15Enable beep (audio signal)
This function allows you to engage or disengage the alarm signal emitted by the stove to indicate that it has received the remote control’s commands.
ENABLE BEEP (audio signal)
English
Function
Select enable beep
menu
Action
Display
ENABLE
BEEP
Press the MENU key. Using the SELECT MENU key select the “ENABLE
BEEP” menu and confirm by pressing the SET key.
11
Select enable or
disable beep
Press the SELECT MENU key and select “ON” to enable the buzzer or
“OFF” to disable it. Confirm by pressing the SET key. After confirmation the
readout “BUZZER ENABLES” will appear on the display while the initial
display will automatically reappear on the remote control.
11
MODE
BEEP
ON
DT2040065-03
DT2010248-04
6.16Stove status
This function displays the stove status under the various operating conditions.
STOVE STATUS
Function
Select stove status
menu
Action
Display
STATE
STO
AV
T EE
STOVE
Press the MENU key, then using the SELECT MENU key select the stove
status “STATE STOVE” menu. Confirm by pressing the SET key.
1
Display stove status
46
The first line displays the operating conditions, the second line for how
long the pellets have been loading and the third line the smoke and room
temperatures detected by the sensors. A list of the readouts which can
appear in the first line is given below:
PUL
Clean grate
ALF 1
Pressure switch activated
Fire door open
Fuel hopper lid open
ALF 2
Anomaly in the pressure switch
ALC
Safety thermostat activated
NO CONN
Smoke sensor disconnected
NO ACC
Failed ignition
MASS TEMP Smoke alarm activated - maximum temperature reached.
H07025240/DT2000723 – 01
1
1
1
PUL
02 . P
4U
CO
L
2 0 3 F0 2 . 47 C9 OF
203F
79F
DT2040071-05
DT2010248-04
6.17Modifying the transmission unit
Should two pellet stoves of the same model be installed close to each other and the remote control beam activates both simultaneously, it is possible
to modify the transmission unit when the stove has been shut down by taking the following steps:
SELECT UNIT
Select UNIT function
Restart stove
Action
Display
SE
ELEC
CT
S
S E LL E
E C TT
UN
NIT
U
U N II TT
Open the flap and press the SET and OPT keys simultaneously. Using the
SELECT MENU key choose one of the eight transmission units (0 - 8).
Standard setting on pellet stoves is 0.
2
2
2
SE
EAR
RCH
H
S
SEA
ARC
CH
F II E
ELD
F
F I E LL D
D
Disconnect the power cable. Reconnect it and within five seconds press
the ON/OFF key, keeping it pressed down for approx. 3 - 4 seconds.
An audible beep indicates the successful change of unit.
Two display pages will appear in sequence while the remote control will
return to the initial display.
aaUnit storage remains as set even without batteries. English
Function
U
N II TT
U
UN
NI T
L
AD
ED
LL O
O
OA
AD
DE
ED
D
2
2
2
1
1
1
DT2040072-05
DT2011839-00
6.18‘Multifuoco’ system operation
The pellet stove with ‘Multifuoco System’ is fitted with one/two fans for the circulation of hot air according to the model.
This system allows several solutions for the distribution of ducted hot air, so that the user has freedom of choice as regards the number of adjoining
rooms which can be heated.
Operation of the ‘Multifuoco System’ will be explained in general and conceptual terms below.
In order to adjust the fan to suit the chosen ducting solution, three ‘Multifuoco System’ speed settings have been pre-programmed, which appear
as 01, 02, 03 in the bottom line of the display and as small rectangles from 1 to 3 in the top line.
There is a greater volume of air transferred by the fan passing from speed setting 01 to 03.
Once the ‘Multifuoco System’ speed has been set, the user can choose a higher or lower amount of heat by selecting one of the four power settings
on the stove: P1, …, P4.
Similarly, there is a greater quantity of hot air produced by the stove passing from power setting P1 to P4.
It is at the user’s discretion, based upon experience and familiarity in using the product, which of the ‘Multifuoco’ speed settings and which power
level to choose.
These choices will be based on the length of the ducting and the required room temperature (as an indication, the longer the ducting the higher the
Multifuoco System speed setting).
For each of the solutions described in the INSTALLATION section under “MULTIFUOCO SYSTEM”, there is a specific Multifuoco fan setting
recommended.
If opting for SOLUTION 1, it is best to use the control panel to select the speed setting “01”.
If opting for SOLUTION 2, a higher fan speed will be required, in which case the speed setting on the control panel shall not be lower than “02”.
Finally, if opting for SOLUTION 3, an even higher fan speed will be required, in which case it would be best to select the speed setting “03” on the
control panel.
To select the required Multifuoco setting, refer to the paragraph “STARTUP AND NORMAL OPERATION”.
H07025240/DT2000723 – 01
47
DT2010994-00
6.19Safety devices
aaDuring operation some parts of the stove (door, handle, ceramic parts) can reach high temperatures.
English
Remember to maintain the safety distances indicated previously.
Be careful, take all due precautions and always comply with the instructions.
If during operation smoke leaks from any part of the stove or the flue, shut the stove down immediately and ventilate the room. When the stove has
cooled, check for the cause of the leak and if necessary call in specialist personnel.
The stove is fitted with several safety devices to guarantee safe operation.
aaThe safety devices are fitted to eliminate the risk of injury to people and pets and damage to property. Tampering or work carried out
by unauthorised personnel can jeopardise this function.
Possible warnings of problems
Simple operating problems can usually be resolved with the help of the following pages.
SMOKE CHAMBER PRESSURE
Sensor
Description
Display
Connected to the flue gas outlet, its function is to control the vacuum
inside the outlet duct so that the stove can be used in all safety.
Pressure switch
“ALF 1”
WHEN ACTIVATED
If correct operating conditions in the flue gas outlet change (incorrect
installation, blockages or obstructions in the flue, poor maintenance,
unfavourable weather conditions such as persistent wind, etc.) the
pressure switch cuts off the power supply to the fuel-loading auger,
thereby stopping the supply of pellets to the grate and starting the stove
shutdown process.
•The readout “ALF 1” appears in the STOVE STATUS mode.
•The readout “SMOKE SAFETY “ appears on the display.
•After approx. 60 seconds the alarm sounds (if activated).
WHAT TO DO
•Shut down the stove by holding the ON/OFF key down for several
seconds.
•The alarm stops.
•Wait until you are sure that combustion of any pellets remaining in the
grate has stopped.
•Wait until the stove has cooled down, then check for and remove
whatever has caused the safety device to be triggered. Finally, after
having cleaned the grate restart the stove by pressing the ON/OFF key.
!
SAFETY
SMOKE
1
1 2 : 00 73F
!
SAFETY
SMOKE
1
1 2 : 00 73F
Its function is to check correct operation of the pressure switch so that the
stove can be used in all safety.
Pressure switch
“ALF 2”
WHEN ACTIVATED
It activates during the “START” stage of the stove (see “STARTING THE
STOVE” table).
If an anomaly is detected in the pressure switch, the readout “ALF 2”
appears in the STOVE STATUS mode.
The readout “SMOKE SAFETY” appears on the display.
After approx. 60 seconds the alarm sounds (if activated).
WHAT TO DO
•Shut down the stove by holding the ON/OFF key down for several
seconds.
•The alarm stops.
•Call the After-Sales Service Centre.
!
SAFETY
SMOKE
1
!
SAFETY
SMOKE
1
48
H07025240/DT2000723 – 01
1 2 : 00 73F
DT2040095-00
1 2 : 00 73F
PELLET HOPPER HOUSING TEMPERATURE
Sensor
Description
Display
Located on the pellet hopper, its function is to prevent excessive
temperature ranges.
TANK TEMP
SAFETY
1
English
Thermostat with
automatic reset
!
WHEN ACTIVATED
If the pellet hopper temperature reaches critical levels, the thermostat
cuts off the power supply to the fuel-loading auger, thereby stopping the
supply of pellets to the grate and starting the stove shutdown process.
•The readout ‘ALC’ appears in the STOVE STATUS mode.
•After approx. 60 seconds the alarm sounds (if activated).
1 2 : 00 73F
WHAT TO DO
Shut down the stove by holding the ON/OFF key down for several seconds.
•The alarm will stop.
•Wait until combustion of any pellets remaining in the grate has finished.
•After having cleaned the grate, restart the stove by pressing the ON/
OFF key. (The readout TANK TEMP SAFETY must no longer appear on
the display. If this is not the case repeat the process described above.)
DT2010995-00
FLUE GAS TEMPERATURE SENSOR
Sensor
Description
Display
Connected to the electronic board, it constantly monitors the working
temperature allowing the stove to be used in all safety.
Smoke sensor
WHEN ACTIVATED
If the temperature exceeds the fixed safety limit the board cuts off the
power supply to the fuelloading auger thus depriving the grate of pellets
and starting the stove shutdown process.
•In the upper part of the display appears the message “SAFETY” and in
the lover part appears “STOVE”.
•The readout ”MASS TEMP” and the flue gas temperature appear in the
STOVE STATUS mode.
•After approx. 60 seconds the alarm sounds (if activated).
WHAT TO DO
•Shut down the stove by holding the ON/OFF key down for several seconds.
•The alarm stops.
•Wait until you are sure that combustion of any pellets remaining in the grate
has stopped.
•Check for and remove whatever has triggered the safety device.
•After having cleaned the grate restart the stove by pressing the ON/OFF key.
!
SAFETY
STOVE
1 2 : 00 73F
1
!
!
1
Smoke sensor
Disconnected
!
PROBE
SMOKE
1
WHAT TO DO
•Shut down the stove by holding the ON/OFF key down for several
seconds.
•The alarm stops.
•Call the After-Sales Service Centre.
H07025240/DT2000723 – 01
S1 M2 O: K0 E0 7 3 F
1 2 : 00 73F
1
WHEN ACTIVATED
If the sensor is momentarily or accidentally removed from its normal
position, or is not connected properly to the electronic board, the readout
“NO CONN” and the flue gas temperature will appear in the STOVE STATUS
mode.
After approx. 60 seconds the alarm sounds (if activated).
SAFETY
PS RT OO VB EE
1 2 : 00 73F
DT2040054-05
49
STOVE ROOM TEMPERATURE SENSOR
Sensor
Description
Display
English
Connected to the rear of the stove, it constantly monitors the temperature
in the immediate vicinity of the stove to ensure that it can be operated in
all safety.
Room sensor
WHEN ACTIVATED
If the sensor is momentarily or accidentally removed from its normal
position, the problem does not require the immediate shutdown of the
stove, which will continue to operate normally at the set power level.
The problem will be indicated on the display by the readout “TON”.
LEVEL
P2
1 2 : 00
1
WHAT TO DO
•Put the sensor back in its proper position.
•If the room temperature display has been activated, it will once again
be shown.
T ON
DT2040055-03
DT2010087-04
6.20Opening the door
aaDuring operation the door must remain closed.
It is to be opened only when the stove has been shut down and
cooled for the carrying out of maintenance.
Fig. 57
Since the fire box door handle can reach hot temperature, the appliance
is fitted with a detachable handle on the rear panel of the stove as
shown in the figure.
The detachable handle, which is standard MUST be used at all times
when opening the door as follows:
-- Hold the detachable handle in the position as shown in the figure;
DT2033033-00
-- Slide the tool onto the fire door handle from below upwards;
Fig. 58
Fig. 59
-- Gently lift upwards towards you and pull door open.
DT2033031-00
50
H07025240/DT2000723 – 01
DT2033032-00
DT2010335-02
6.21Humidifier
The stove comes with the standard fitting of a humidifier tray located inside the top part, under the grille in front of the pellet hopper.
To fill the tray with water, remove the top grille and use the appropriate spray bottle provided.
The tray P955 holds 17 oz (50 cl) of water (P956 34 oz (100 cl)), which will last about 2 or 3 days depending on stove use.
aaWhen refilling the humidifier do not exceed the maximum capacity, shown as MAX, otherwise the electrical parts of the stove could
be damaged.
Fig. 60
GRILLE
Fig. 62
Fig. 61
DT2030534-01
English
P956
P955
Fig. 63
GRILLE
DT2030535-00
DT2030532-01
DT2030533-00
DT2010049-04
6.22Disposal of ashes
Ash from natural (non-treated) wood burned in stoves or open fireplaces is composed mainly of calcium, silicon, potassium and magnesium oxides.
The ashes can therefore be used as a fertiliser for plants or in the garden, albeit not exceeding 5.7 lb per 12 yd2 annually.
aaAshes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be placed on a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ashes are disposed of by
burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have beeen thoroughly
cooled.
ddOnly when they have been fully extinguished can the ashes be thrown away with organic waste, assuming that nails or other nonorganic material are not present.
H07025240/DT2000723 – 01
51
English
7.0 MAINTENANCE
DT2010249-01
Pursuant to current regulations on the safety of electrical equipment, you must contact a Piazzetta Group After-Sales Service Centre or a qualified
electrician for all and any work connected with installation, maintenance or servicing that involves access to electrical parts.
Maintenance is to be considered compulsory for correct and efficient stove operation. If maintenance is not carried out with the recommended
frequency, stove performance could suffer. The manufacturer will not be responsible for stove deterioration or malfunction if due to poor maintenance.
The frequency of cleaning depends on how much the stove is used and the quality of the fuel.
All maintenance work (cleaning, any replacements, etc.) must be carried out when the stove is shutdown, completely cold and the supply cable
disconnected.
Do not use materials that could scratch or damage the glass, since scratches could become cracks. Under no circumstances use abrasive
DT2010057-02
substances.
DT2010089-05
7.1 Cleaning the grate and the grate support
Clean the grate area periodically (approx. once every two days) and
whenever the stove is to be lit:
-- remove the grate baffle plate and lift out the grate;
-- remove any ash or other material that may have built up, taking
particular care to free any clogged holes using a sharp pointed tool;
-- make sure the “ignition hole”, located on the left side of the grate, is
kept clean;
-- check the grate support and remove any ash.
Fig. 64
Grate baffle plate
Grate
Ash pan
DT2030814-02
aaAfter cleaning and before lighting the stove, check that the
Fig. 65
IGNITION HOLE
grate is correctly inserted and pushed towards the left. Refit
the grate baffle plate.
DT2030894-00
DT2010100-03
7.2 Cleaning the ash tray
Every two days, check the ash drawer to see if it needs emptying.
To dispose of the ashes, refer to the paragraph “DISPOSAL OF ASHES”.
DT2010428-03
7.3 Cleaning the firebox
Once a week clean the firebox as follows.
-- Remove the grate baffle and draw out the grate.
-- Turn the eccentric clamps to free the internal baffle.
-- Lift the baffle slightly, gripping it by the two outer tabs to free it at the
bottom and then turn it, bringing the bottom outwards, and remove.
-- Using a vacuum cleaner remove the ash from the firebox.
-- After having thoroughly cleaned the firebox, remount the internal
baffle proceeding in the reverse order to above.
-- Ensure that the tabs are properly inserted into the relative notches
in the sides of the firebox and secure the baffle by turning the two
eccentric clamps.
-- Replace the grate, pushing it to the left and the grate baffle.
Fig. 66
ECCENTRIC CLAMP
INTERNAL BAFFLE
A
A DETAIL
TABS
aaThis type of cleaning requires a vacuum cleaner suitable for
holding ash.
BOTTOM RESTRAINT
DT2030725-00
52
H07025240/DT2000723 – 01
DT2010127-03
7.4 Cleaning the smoke chamber
Fig. 67
English
Once a year clean the smoke chamber as follows:
-- remove the screws which secure the smoke chamber cover, then lift it
slightly and take it out by pulling it towards you (Fig. 67 - 68);
DT2030185-01
Fig. 68
DT2030186-01
-- use a vacuum cleaner to remove any ash and carbon deposits which
can accumulate in the chamber, taking care not to damage the blades
of the fan (Fig. 69);
-- check the hole inside the smoke chamber on the left side (leading to
the device for measuring the vacuum) for dust and ash and clean if
necessary;
-- after thorough cleaning, change the gasket and replace the smoke
chamber closing element.
Fig. 69
CLEAN
HOLE
DT2030187-02
DT2010092-03
7.5 Cleaning the flue system
Soot and Flyash: formation and need for removal.
Fig. 70
The products of combustion will contain small particles of flyash. The
flyash will collect in the exhaust venting system and restrict the flow of
the flue gases. Incomplete combustion, such as occurs during startup,
shutdown, or incorrect operation of the room heater will lead to some
soot formation which will collect in the exhaust venting system. The
exhaust venting system should be inspected at least once every two
months during the heating season to determine if cleaning is necessary.
Until you have got reasonably used to the operating conditions of
the stove, we recommend that this maintenance be carried out on a
monthly basis.
DT2031151-00
Remove the plug from the Tee and clean the pipes.
Do not use a metal trush to clean this vent. Such a brush may scratch
the vent liner and promote corrosion. Do not use chemical cleaners in
this vent system. They do not eliminate need for manual cleaning and
may be corrosive to vent materials.
If necessary, particularly on the first few occasions, we recommend
calling in a qualified technician.
H07025240/DT2000723 – 01
53
DT2010059-03
7.6 Cleaning the ceramic cladding
The ceramic cladding must first be cleaned with a soft dry cloth before using any detergent (even mild detergent).
Products are available on the market which are suitable for cleaning ceramics as well as concentrated products for cleaning porcelain. These will
remove oil, ink, coffee and wine stains, etc.
English
ddNever soak the ceramic cladding or clean it with cold water when it is still hot as the thermal shock could cause it to crack.
DT2010061-03
7.7 Cleaning the enamelled metal parts
When cleaning the enamelled metal parts of the product use a soft cloth moistened with water
ddNever clean metallic parts using alcohol, solvents, petroleum-based products, acetones or other degreasing or abrasive substances.
In the event of such substances being used, the manufacturer will not be responsible for any damage caused.
Discolouration of metallic parts may be the result of misuse.
DT2010062-05
7.8 Cleaning the glass (daily)
aaThe glass should be cleaned when cold using ammonia-based degreasing agents and not corrosive substances such as solvents.
Although it is likely that tar will build up on the glass during the lighting stage, it will burn off with the stove in full operation.
If, however, the tar is left to build up over a long period it will require more effort to remove.
We therefore recommend that the glass be cleaned daily before lighting the stove.
ddDo not use any material that could scratch or spoil the glass, as scratches may develop into cracks or breaks.
DT2010093-06
7.9 Replacing the window
The stove is fitted with a 0.197” / (5 mm) thick glass panel, resistant to thermal shock up to 1382°F / (750°C); the glass can only be broken by heavy
impact or misuse.
Do not slam the door or hit the window.
In case of breakage replace only with a Gruppo Piazzetta spare part.
To replace, proceed as follows:
-- wear protective gloves;
-- remove the door and lie it flat;
-- loosen the screws visible on the inside of the door;
-- remove the frame and glass carefully;
-- if the fibreglass seal and glazing bead have deteriorated, replace them;
-- change the glass panel then replace the frame, tightening the screws carefully but not excessively;
-- remount the door.
If other problems occur, consult your nearest retailer.
54
H07025240/DT2000723 – 01
DT2010218-06
7.10Replacing the remote control batteries
Fig. 71
T ES T HW 4
I N I Z I ALE
aaRechargeable batteries are unsuitable for the remote control
as they do not guarantee sufficient voltage for correct
operation.
Replace the back cover on the remote control.
The writing shown to the side appears on the display of the remote
control.
A feedback procedure between the remote control and the receiver
starts automatically.
After a few seconds the initial display returns.
In other words, stove status prior to changing the batteries will be
displayed.
E.g.: if the stove was shut down, the display will appear as shown to
the side.
The new batteries must be of the same type as above; failure to comply
with these instructions could cause a risk of explosion.
The old batteries must be disposed of properly in compliance with
the applicable laws in force.
VER4
English
Slide the cover off the back of the remote control and replace the
batteries with new ones ensuring that the (+) and (–) directions are
correct.
The batteries must be of the type AAA (LR03) 1.5V.
OFF
1
09 : 53
68F
DT2010218-01
DT2010095-06
7.11Cleaning the fans
aaAny cleaning or maintenance work must be carried out after the CURRENT HAS BEEN SWITCHED OFF.
The stove is fitted with fans (smoke extractor and heating) positioned at the bottom rear of the stove.
Any build-up of dust or ash on the blades can unbalance them resulting in noise during operation.
It is necessary to have the fans cleaned annually. Since such an operation involves dismantling certain parts of the stove, have the cleaning carried
out only by a Piazzetta Service Centre or other qualified persons.
DT2010096-05
7.12When not in use
When shutting the stove down for the summer, proceed as follows:
-- remove all pellets from the hopper and feeding auger;
-- carefully clean the grate, the grate support and the ash drawer;
-- using a steel brush, clean the baffle plate or internal baffle plates of the firebox and coat them using the spray paint, supplied with the kit, to prevent
them from oxidising and consequently forming rust.
aaIf the cast-iron parts inside the firebox are not coated, rust could form. This is a natural process, which does not affect the efficiency
and quality of the product.
-- Clean the flue thoroughly: contact a professional chimneysweep for this purpose;
-- clean by removing all dust, cobwebs, etc. from the area behind the inner lining panels once a year, in particular the fans;
-- disconnect the power cable from the power supply;
-- remove the batteries from the remote control.
DT2010097-03
7.13Extraordinary maintenance
The following maintenance should be carried out ONCE A YEAR and is necessary to ensure efficient and safe stove operation:
-- clean the firebox thoroughly;
-- clean and inspect the flue;
-- check the condition of seals and gaskets;
-- clean mechanical and moving parts (motors and fans);
-- check electrical and electronic components.
H07025240/DT2000723 – 01
55
8.0 TROUBLESHOOTING
DT2011179-01
aaSome of the problems indicated below may be resolved by following the instructions. All work must be carried out when the appliance
is cold and disconnected from the electricity supply (pull out the plug).
English
aaAuthorised qualified persons must be contacted, in accordance with current regulations, whenever it is necessary to work on parts
inside the cladding or the firebox in order to resolve the problem.
It is therefore recommended that only “Gruppo Piazzetta S.p.A.” authorised Service Centres be contacted.
Whenever authorised Service Centre personnel carry out work, they must show an identity card issued by Gruppo Piazzetta S.p.A.
on which the following are printed: name of the Service Centre, stamp and signature of the company and the period of validity of the
actual document.
aaUnauthorised tampering with the appliance or the use of other than original spare parts not only creates situations of risk for operator
safety, but invalidates the warranty and relieves the manufacturer from all liability.
Problem
The control panel display is not lit
Stove combustion gas safety device
“ALF 1” stove status
56
Cause
Solution
The appliance is not powered
Check that the power cable is plugged
into the wall socket and connected to
the appliance
Faulty power cable
Replace the power cable (use only
original spares)
Fuses blown
Check the fuses in both the plug and
the electronic board, replacing them if
necessary. If the problem persists call
an electrician
Faulty control panel
Replace the control panel (use only
original spares)
Faulty flat cable
Replace the flat cable (use only
original spares)
Faulty electronic board
Replace the electronic board (use only
original spares)
Blocked flue or flue gas outlet
Check and clean the flue and the
outlet
Fire door open
Control if the door is closed
Fuel hopper lid remained opened for
more than 45 s
Control if the lid is closed
Broken smoke extractor
Replace the motor (use only original
spares)
Flue system too long
Check correct installation
Damaged door sealing gaskets
Check all the gaskets and seals of the
door and flue pipe
Hose connection blocked
Dismantle and clean the hose
connection for the vacuum gauge
Silicone piping blocked or broken
Check and/or replace piping
Faulty electronic board
Replace the electronic board (use only
original spares)
H07025240/DT2000723 – 01
Problem
Solution
Faulty pressure switch
Replace the pressure switch (use only
original spares)
No power supply to the auger
Check the electrical connections
(contact a Piazzetta After-Sales
Service Centre or an authorised
person)
Blocked flue
Check and clean the flue
Grate requires cleaning
Clean the grate (see section 7.1)
Faulty thermostat
Replace hopper thermostat (use only
original spares)
Faulty electronic board
Replace the electronic board (use only
original spares)
Faulty fan
Check fan operation and replace if
necessary (use only original spares)
“PUL” stove status
Momentary power failure during
operation
The stove restarts automatically and
continues operating normally at power
level 2
“NO ACC” stove status
Empty hopper
Fill the hopper
Grate requires cleaning
Clean the grate (see section 7.1)
Operating temperature not reached
Empty the grate and restart
Faulty glow plug (igniter)
Replace glow plug (use only original
spares)
Faulty electronic board
Replace the electronic board (use only
original spares)
Thermal cutout
“ALC” stove status
(Hopper thermostat)
English
Pressure switch malfunction
“ALF 2” stove status
Cause
H07025240/DT2000723 – 01
57
Problem
English
Stove safety device
“MASS TEMP” stove status
Smoke sensor
“NO CONN” stove status
Appliance runs for 9-10 minutes and
then goes out
Cause
Solution
Blocked flue or flue gas outlet
Clean the flue and the outlet
Faulty electronic board
Replace the electronic board (use only
original spares)
Faulty limit temperature control sensor
Replace the control sensor (use only
original spares)
Badly positioned smoke sensor
Check that the sensor is correctly
positioned (see wiring diagram)
Incorrect parameter settings
Check parameter settings
No connection between the 2-pin
terminal of the smoke sensor or the
ambient and the electronic board
Check correct insertion/position of the
connector (see wiring diagram)
Faulty electronic board
Replace the electronic board (use only
original spares)
Badly positioned smoke sensor
Check that the sensor is correctly
connected
Heat sensor locked
Repeat ignition procedure. If the
problem persists, contact an
authorised technician
Combustion gases have not reached
the required ignition temperature
Repeat ignition procedure. If the
problem persists, contact an
authorised technician
Heat sensor badly connected
Check the wiring and connections
Blocked flue
Clean flue system
Failed ignition
See “NO ACC”
Faulty electronic board
Replace the electronic board (use only
original spares)
Pellet-charging system blocked
Empty the pellet hopper; check and
clean the auger and chute
aaThis instruction booklet contains all the necessary information for installation, operation and maintenance.
Only call the Gruppo Piazzetta S.p.A. service centre after having scrupulously followed all the instructions.
58
H07025240/DT2000723 – 01
DT2010557-02
8.1 Replacing the fuses
Electronic board fuse.
Unscrew the cartridge fuse or safety plug from the electronic board and
replace with a similar one.
Fig. 72
English
Motherboard fuse type: F6.3AL250V.
Bouchon porte-fusible
DT2032940-00
Fuse on the IEC power socket.
Draw out the fuse carrier and replace the fuse with the spare to be
found inside the small drawer.
Fig. 73
Type:F6.3AH250V
Fuse carrier drawer
DT2030897-00
REFERENCE STANDARDS
DT2010209-05
ASTM E1509��������������������������������������������������������������������������������������Standard specification for room heaters, pellet fuel – burning type
UL 1482��������������������������������������������������������������������������������������������Room heaters, solid fuel type
ULC S627������������������������������������������������������������������������������������������Canadian standards needed for pellet fuel stoves
UL 181����������������������������������������������������������������������������������������������Factory made air ducts and connectots
UL 641����������������������������������������������������������������������������������������������Low-temperature venting system, type L
ULC S609������������������������������������������������������������������������������������������Low-temperature vents, type L
Manufactured home and safety standard (HUD), cfr 3280, part 24�����Mobile home installation
NFPA (Fire) 211����������������������������������������������������������������������������������Standard for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances
H07025240/DT2000723 – 01
59
Via Montello, 22
31011 Casella d’Asolo (TV) - ITALY
Tel. +39.04235271 - Fax +39.042355178
www.piazzetta.it
e-mail:infopiazzetta@piazzetta.it
Gruppo Piazzetta S.p.A. Technical Department - Cod. H07025240 / DT2000723 - Rev. 01 - (05/2011)
Product serial number, to be quoted when requesting service
from the Gruppo Piazzetta After-Sales Service Centre.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising