X-Pro2 - FUJIFILM app

X-Pro2 - FUJIFILM app
BL00004725-203
DIGITAL CAMERA
X-Pro2 Version 3.10
Owner’s Manual
Thank you for your purchase of this product. This
manual describes how to use your FUJIFILM X-Pro2
digital camera. Be sure that you have read and understood its contents before using the camera.
■ Product website:
http://fujifilm-x.com/x-pro2/
■ Additional information may be found in online manuals available from:
http://fujifilm-dsc.com/manuals/
EN
Before You Begin
First Steps
Basic Photography
and Playback
Basic Movie Recording
and Playback
The Q (Quick Menu) Button
The Fn (Function) Buttons
More on Photography
and Playback
Menus
Connections
Technical Notes
Troubleshooting
Appendix
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and operating instructions
should be read before the appliance is operated.
• Retain Instructions: The safety and operating instructions
should be retained for future reference.
• Heed Warnings: All warnings on the appliance and in the
operating instructions should be adhered to.
• Follow Instructions: All operating and use instructions
should be followed.
Installation
Power Sources: This video product should be operated only
from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company. For video products intended to operate from battery
power, or other sources, refer to the operating instructions.
This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation
is provided or the manufacturer’s instructions have been
adhered to. This video product should never be placed near
or over a radiator or heat register.
Attachments: Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
Water and Moisture: Do not use this video product near water—for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
Power-Cord Protection: Power-supply cords should be routed
so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the
Grounding or Polarization: This video product is equipped point where they exit from the appliance.
with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the Accessories: Do not place this video product on an unstable
power outlet only one way. This is a safety feature. If you cart, stand, tripod, bracket, or table. The video product may
are unable to insert the plug fully into the outlet, try revers- fall, causing serious injury to a child or adult, and serious
ing the plug. If the plug should still fail to fit, contact your damage to the appliance. Use only with a cart, stand, trielectrician to replace your obsolete outlet. Do not defeat pod, bracket, or table recommended by the manufacturer, or
sold with the video product. Any mounting of the appliance
the safety purpose of the polarized plug.
should follow the manufacturer’s instructions, and should use
Alternate Warnings: This video product is equipped with a mounting accessory recommended by the manufacturer.
a three-wire grounding-type plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding- An appliance and cart combination
type power outlet. This is a safety feature. If you are unable should be moved with care. Quick
to insert the plug into the outlet, contact your electrician to stops, excessive force, and uneven
replace your obsolete outlet. Do not defeat the safety pur- surfaces may cause the appliance
and cart combination to overturn.
pose of the grounding type plug.
Overloading: Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
Ventilation: Slots and openings in the cabinet are provided
for ventilation, to ensure reliable operation of the video
product and to protect it from overheating, and these openings must not be blocked or covered. The openings should
never be blocked by placing the video product on a bed,
sofa, rug, or other similar surface.
ii
Antennas
Outdoor Antenna Grounding: If an outside antenna or cable
system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70,
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
Ground Clamp
Antenna Lead
in Wire
Electric Service
Equipment
Antenna
Discharge Unit
(NEC SECTION
810-20)
Ground Clamps
Power Service Grounding Electrode
System (NEC ART 250. PART H)
Grounding Conductors
(NEC SECTION 810-21)
Power Lines: An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
Use
Cleaning: Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
Object and Liquid Entry: Never push objects of any kind into this
video product through openings as they may touch dangerous
voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.
Lightning: For added protection for this video product receiver during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the video product due to lightning and
power-line surges.
For Your Safety
Service
Be sure to read these notes before use
Servicing: Do not attempt to service this video product
Safety Notes
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to • Make sure that you use your camera correctly. Read these
qualified service personnel.
safety notes and your Owner’s Manual carefully before use.
Damage Requiring Service: Unplug this video product from • After reading these safety notes, store them in a safe place.
the wall outlet and refer servicing to qualified service perAbout the Icons
sonnel under the following conditions:
The icons shown below are used in this document to indi• When the power-supply cord or plug is damaged
cate the severity of the injury or damage that can result if the
• If liquid has been spilled, or objects have fallen into the
information indicated by the icon is ignored and the product
video product.
is used incorrectly as a result.
• If the video product has been exposed to rain or water.
• If the video product has been dropped or the cabinet has
This icon indicates that death or seribeen damaged.
WARNING ous injury can result if the information
If the video product does not operate normally follow the
is ignored.
operating instructions. Adjust only those controls that are
This icon indicates that personal injury
covered by the operating instructions as an improper adjustCAUTION or material damage can result if the inment of other controls may result in damage and will often
formation is ignored.
require extensive work by a qualified technician to restore
The icons shown below are used to indicate the nature of the
the video product to its normal operation.
instructions which are to be observed.
When the video product exhibits a distinct change in perforTriangular icons tell you that this information remance — this indicates a need for service.
quires attention (“Important”).
Replacement Parts: When replacement parts are required,
Circular icons with a diagonal bar tell you that the
be sure the service technician has used replacement parts
action indicated is prohibited (“Prohibited”).
specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
Filled circles with an exclamation mark indicate an
action that must be performed (“Required”).
Safety Check: Upon completion of any service or repairs to The symbols on the product (including the accesories) repthis video product, ask the service technician to perform resent the following:
safety checks to determine that the video product is in
AC
proper operating condition.
DC
Class II equipment (The construction of the product is double-insulated.)
WARNING
Unplug
from power
socket
Do not use in
the bathroom
or shower
Do not disassemble
Do not touch
internal parts
If a problem arises, turn the camera off, remove the
battery, and disconnect and unplug the AC power
adapter. Continued use of the camera when it
is emitting smoke, is emitting any unusual odor,
or is in any other abnormal state can cause a fire
or electric shock. Contact your FUJIFILM dealer.
Do not allow water or foreign objects to enter the
camera. If water or foreign objects get inside the
camera, turn the camera off, remove the battery,
and disconnect and unplug the AC power adapter. Continued use of the camera can cause a fire
or electric shock. Contact your FUJIFILM dealer.
Do not use the camera in the bathroom or shower.
This can cause a fire or electric shock.
Never attempt to change or take apart the camera
(never open the case). Failure to observe this precaution can cause fire or electric shock.
Should the case break open as the result of a fall or
other accident, do not touch the exposed parts. Failure to observe this precaution could result in electric shock or in injury from touching the damaged
parts. Remove the battery immediately, taking
care to avoid injury or electric shock, and take the
product to the point of purchase for consultation.
Do not change, heat or unduly twist or pull the connection cord and do not place heavy objects on the
connection cord. These actions could damage the
cord and cause a fire or electric shock. If the cord
is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface. This
can cause the camera to fall or tip over and cause
injury.
Never attempt to take pictures while in motion. Do
not use the camera while walking or driving. This
can result in you falling down or being involved in
a traffic accident.
iii
For Your Safety
WARNING
Do not touch any metal parts of the camera during
a thunderstorm. This can cause an electric shock
due to induced current from the lightning discharge.
Do not use the battery except as specified. Load the
battery as shown by the indicator.
Do not disassemble, modify, or heat batteries. Do not
drop, strike, or throw batteries or otherwise subject
them to strong impacts. Do not use batteries that
show signs of leaking, deformation, discoloration, or
other abnormalities. Use only designated chargers
to recharge rechargeable batteries and do not attempt to recharge non-rechargeable Li-ion or alkaline
batteries. Do not short batteries or store them with
metallic objects. Failure to observe these precautions could result in the batteries overheating,
igniting, rupturing, or leaking, causing fire, burns,
or other injury.
Use only batteries or AC power adapters specified for
use with this camera. Do not use voltages other than
the power supply voltage shown. The use of other
power sources can cause a fire.
If the battery leaks and fluid gets in contact with your
eyes, skin or clothing, flush the affected area with
clean water and seek medical attention or call an
emergency number right away.
Do not use the charger to charge batteries other than
those specified here. The supplied charger is for
use only with batteries of the type supplied with
the camera. Using the charger to charge conventional batteries or other types of rechargeable
batteries can cause the battery to leak, overheat
or burst.
Using a flash too close to a person’s eyes may cause
visual impairment. Take particular care when photographing infants and young children.
iv
WARNING
Do not remain in prolonged contact with hot surfaces.
Failure to observe this precaution could result in
low-temperature burns, particularly at high ambient temperatures or with users who suffer from
poor circulation or reduced sensation, in which
case use of a tripod or similar precautions are
recommended.
Do not leave one part of the body in contact with the
product for prolonged periods while the product is
on. Failure to observe this precaution could result
in low-temperature burns, particularly during
prolonged use, at high ambient temperatures,
or with users who suffer from poor circulation or
reduced sensation, in which case use of a tripod
or similar precautions are recommended.
Do not use in the presence of flammable objects, explosive gases, or dust.
When carrying the battery, install it in a digital camera or keep it in the hard case. When storing the battery, keep it in the hard case. When discarding, cover
the battery terminals with insulation tape. Contact
with other metallic objects or batteries could
cause the battery to ignite or burst.
Keep memory cards, hot shoes, and other small parts
out of the reach of small children. Children may
swallow small parts; keep out of reach of children.
Should a child swallow a small part, seek medical
attention or call emergency.
Keep out of reach of small children. Among the elements that could cause injury are the strap, which
could become entangled about a child’s neck,
causing strangulation, and the flash, which could
cause visual impairment.
Follow the directions of airline and hospital personnel. This product generates radio-frequency
emissions that could interfere with navigational
or medical equipment.
CAUTION
Do not use this camera in locations affected by oil
fumes, steam, humidity or dust. This can cause a
fire or electric shock.
Do not leave this camera in places subject to extremely
high temperatures. Do not leave the camera in
locations such as a sealed vehicle or in direct sunlight. This can cause a fire.
Do not place heavy objects on the camera. This can
cause the heavy object to tip over or fall and
cause injury.
Do not move the camera while the AC power adapter
is still connected. Do not pull on the connection cord
to disconnect the AC power adapter. This can damage the power cord or cables and cause a fire or
electric shock.
Do not cover or wrap the camera or the AC power
adapter in a cloth or blanket. This can cause heat
to build up and distort the casing or cause a fire.
When you are cleaning the camera or you do not plan
to use the camera for an extended period, remove
the battery and disconnect and unplug the AC power
adapter. Failure to do so can cause a fire or electric shock.
When charging ends, unplug the charger from the
power socket. Leaving the charger plugged into
the power socket can cause a fire.
When a memory card is removed, the card could come
out of the slot too quickly. Use your finger to hold it
and gently release the card. Injury could result to
those struck by the ejected card.
Request regular internal testing and cleaning for
your camera. Build-up of dust in your camera
can cause a fire or electric shock. Contact your
FUJIFILM dealer to request internal cleaning every
two years. Please note that this service is not free
of charge.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
For Your Safety
■ Storage
The Battery and Power Supply
Note: Check the type of battery used in your camera and Performance may be impaired if the battery is left unused
for extended periods when fully charged. Run the battery
read the appropriate sections.
flat before storing it.
The following describes the proper use of batteries and how
to prolong their life. Incorrect use can shorten battery life or If the camera will not be used for an extended period, remove the battery and store it in a dry place with an ambient
cause leakage, overheating, fire, or explosion.
temperature of from +15 °C to +25 °C (+59 °F to +77 °F). Do
Li-ion Batteries
not store in locations exposed to extremes of temperature.
Read this section if your camera uses a rechargeable
■ Cautions: Handling the Battery
Li-ion battery.
• Do not transport or store with metal objects such as neckThe battery is not charged at shipment. Charge the battery
laces or hairpins.
before use. Keep the battery in its case when not in use.
• Do not expose to flame or heat.
• Do not disassemble or modify.
■ Notes on the Battery
The battery gradually loses its charge when not in use. • Use with designated chargers only.
• Dispose of used batteries promptly.
Charge the battery one or two days before use.
• Do not drop or subject to strong physical shocks.
Battery life can be extended by turning the camera off when • Do not expose to water.
not in use.
• Keep the terminals clean.
Battery capacity decreases at low temperatures; a depleted • The battery and camera body may become warm to the
touch after extended use. This is normal.
battery may not function when cold. Keep a fully charged
spare battery in a warm place and exchange as necessary, ■ Disposal
or keep the battery in your pocket or other warm place and Dispose of used batteries in accord with local regulations.
insert it in the camera only when shooting. Do not place
the battery in direct contact with hand warmers or other AC Power Adapters (Available Separately)
Use only FUJIFILM AC power adapters designated for use
heating devices.
with this camera. Other adapters could damage the camera.
■ Charging the Battery
• The AC power adapter is for indoor use only.
Charge the battery in the supplied battery charger. Charging
• Be sure the DC plug is securely connected to the camera.
times will increase at ambient temperatures below +10 °C
• Turn the camera off before disconnecting the adapter.
(+50 °F) or above +35 °C (+95 °F). Do not attempt to charge
Disconnect the adapter by the plug, not the cable.
the battery at temperatures above 40 °C (+104 °F); at tem• Do not use with other devices.
peratures below 0 °C (+32 °F), the battery will not charge.
• Do not disassemble.
Do not attempt to recharge a fully charged battery. The bat- • Do not expose to high heat and humidity.
tery does not however need to be fully discharged before • Do not subject to strong physical shocks.
charging.
• The adapter may hum or become hot to the touch during
use. This is normal.
The battery may be warm to the touch immediately after
• If the adapter causes radio interference, reorient or relocate
charging or use. This is normal.
the receiving antenna.
■ Battery Life
At normal temperatures, the battery can be recharged about
300 times. A noticeable decrease in the length of time the
battery will hold a charge indicates that it has reached the
end of its service life and should be replaced.
Using the Camera
• Do not aim the camera at extremely bright light sources,
such as the sun in a cloudless sky. Failure to observe this
precaution could damage the camera image sensor.
• Strong sunlight focused through the viewfinder may damage the panel of electronic viewfinder (EVF). Do not aim
the electronic viewfinder at the sun.
Take Test Shots
Before taking photographs on important occasions (such as
at weddings or before taking the camera on a trip), take a
test shot and view the results to ensure that the camera is
functioning normally. FUJIFILM Corporation can not accept
liability for damages or lost profits incurred as a result of
product malfunction.
Notes on Copyright
Unless intended solely for personal use, images recorded using your digital camera system cannot be used in ways that
infringe copyright laws without the consent of the owner.
Note that some restrictions apply to the photographing of
stage performances, entertainments, and exhibits, even
when intended purely for personal use. Users are also asked
to note that the transfer of memory cards containing images
or data protected under copyright laws is only permissible
within the restrictions imposed by those copyright laws.
Handling
To ensure that images are recorded correctly, do not subject
the camera to impact or physical shocks while images are
being recorded.
v
For Your Safety
Liquid Crystal
In the event that the display is damaged, care should be
taken to avoid contact with liquid crystal. Take the urgent
action indicated should any of the following situations arise:
• If liquid crystal comes in contact with your skin, clean the
area with a cloth and then wash thoroughly with soap and
running water.
• If liquid crystal enters your eyes, flush the affected eye with
clean water for at least 15 minutes and then seek medical
assistance.
• If liquid crystal is swallowed, rinse your mouth thoroughly
with water. Drink large quantities of water and induce
vomiting, then seek medical assistance.
Electrical Interference
NOTICES
This camera may interfere with hospital or aviation equipTo prevent fire or shock hazard, do not expose the unit
ment. Consult with hospital or airline staff before using the
to rain or moisture.
camera in a hospital or on an aircraft.
Please read the “Safety Notes” and make sure you unColor Television Systems
derstand them before using the camera.
NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in the U.S.A., Perchlorate Material—special handling may apply. See
Canada, and Japan. PAL (Phase Alternation by Line) is a color http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
television system adopted mainly in European countries and
China.
Exif Print (Exif Version 2.3)
Exif Print is a newly revised digital camera file format in
Although the display is manufactured using extremely high- which information stored with photographs is used for optiprecision technology, it may contain pixels that are always lit mal color reproduction during printing.
or that do not light. This is not a malfunction, and images
IMPORTANT NOTICE: Read Before Using the Software
recorded with the product are unaffected.
Direct or indirect export, in whole or in part, of licensed software without the permission of the applicable governing
Trademark Information
Digital Split Image is a trademark or registered trademark bodies is prohibited.
of FUJIFILM Corporation. xD-Picture Card and E are
trademarks of FUJIFILM Corporation. The typefaces included
herein are solely developed by DynaComware Taiwan Inc.
Macintosh, Mac OS, and macOS are trademarks of Apple Inc.
in the U.S.A. and other countries. Windows is a registered
trademark of Microsoft Corporation in the U.S.A. and other
countries. Wi-Fi® and Wi-Fi Protected Setup® are registered
trademarks of the Wi-Fi Alliance. The SDHC and SDXC logos
are trademarks of SD-3C, LLC. The HDMI logo is a trademark. All other trade names mentioned in this manual are
the trademarks or registered trademarks of their respective
owners.
vi
For Your Safety
For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device
is designed and manufactured not to exceed the emission
limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government.
effects (by heating tissue), exposure of low-level RF that does
not produce heating effects causes no known adverse health
effects. Many studies of low-level RF exposures have not
found any biological effects. Some studies have suggested
that some biological effects might occur, but such findings
have not been confirmed by additional research. X-Pro2 has
been tested and found to comply with IC radiation exposure
limits set forth for an uncontrolled environment and meets
RSS-102 of the IC radio frequency (RF) Exposure rules.
The exposure standard for wireless device employs a unit
of measurement known as the Specific Absorption Rate, or
SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR
are conducted using standard operating positions accepted
FCC Statement: This device complies with Part 15 of the FCC by the FCC with the device transmitting at its highest certiDisposal of Electrical and Electronic Equipment in Private Households
Rules. Operation is subject to the following two conditions: fied power level in all tested frequency bands.
In the European Union, Norway, Iceland and
(1) This device may not cause harmful interference, and
Liechtenstein: This symbol on the product, or in
(2) this device must accept any interference received, includ- Notes on the Grant: To comply with Part 15 of the FCC Rules,
this product must be used with a Fujifilm-specified ferrite- the manual and in the warranty, and/or on its
ing interference that may cause undesired operation.
packaging indicates that this product shall not
core A/V cable, USB cable, and DC supply cord.
CAUTION: This equipment has been tested and found to combe treated as household waste. Instead it should
ply with the limits for a Class B digital device, pursuant to
be taken to an applicable collection point for the
A lithium ion battery that is recyclable
Part 15 of the FCC Rules. These limits are designed to prorecycling of electrical and electronic equipment.
powers the product you have purchased.
vide reasonable protection against harmful interference in a
Please call 1-800-8-BATTERY for informaBy ensuring this product is disposed of correctly, you will
residential installation. This equipment generates, uses, and
tion on how to recycle this battery.
help prevent potential negative consequences to the encan radiate radio frequency energy and, if not installed and
vironment and human health, which could otherwise be
used in accordance with the instructions, may cause harmful
For Customers in Canada
caused by inappropriate waste handling of this product.
interference to radio communications. However, there is no
CAN ICES-3 (B)/NMB-3(B)
This symbol on the batteries or accumulators inguarantee that interference will not occur in a particular inCAUTION: This Class B digital apparatus complies with Cana- dicates that those batteries shall not be treated
stallation. If this equipment does cause harmful interference
dian ICES-003.
as household waste.
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged Industry Canada statement: This device complies with Industo try to correct the interference by one or more of the fol- try Canada’s licence-exempt RSSs. Operation is subject to If your equipment contains easy removable batteries or
the following two conditions: (1) This device may not cause accumulators please dispose these separately according to
lowing measures:
interference; and (2) This device must accept any interfer- your local requirements.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver. ence, including interference that may cause undesired op- The recycling of materials will help to conserve natural resourc• Connect the equipment into an outlet on a circuit different eration of the device.
es. For more detailed information about recycling this product,
from that to which the receiver is connected.
This device and its antenna(s) must not be co-located or op- please contact your local city office, your household waste
• Consult the dealer or an experienced radio/TV technician erating in conjunction with any other antenna or transmit- disposal service or the shop where you purchased the product.
for help.
ter, except tested built-in radios. The County Code Selection In Countries Outside the European Union, Norway, Iceland and
FCC Caution: Any changes or modifications not expressly ap- feature is disabled for products marketed in the US/ Canada. Liechtenstein: If you wish to discard this product, including
proved by the party responsible for compliance could void Radiation Exposure Statement: The available scientific the batteries or accumulators, please contact your local authe user’s authority to operate this equipment.
evidence does not show that any health problems are as- thorities and ask for the correct way of disposal.
This transmitter must not be co-located or operating in con- sociated with using low power wireless devices. There is no In Japan: This symbol on the batteries indicates
proof, however, that these low power wireless devices are that they are to be disposed of separately.
junction with any other antenna or transmitter.
absolutely safe. Low power Wireless devices emit low levels
of radio frequency energy (RF) in the microwave range while
being used. Whereas high levels of RF can produce health
Contains IC : 7736B-02000002
Contains FCC ID : W2Z-02000002
vii
For Your Safety
Be sure to read these notes before use
Safety Notes
Thank you for your purchase of this product. For repair, inspection, and internal testing,
contact your FUJIFILM dealer.
• Make sure that you use the lens correctly. Read these safety notes and the camera Owner’s
Manual carefully before use.
• After reading these safety notes, store them in a safe place.
About the Icons
The icons shown below are used in this document to indicate the severity of the injury or
damage that can result if the information indicated by the icon is ignored and the product
is used incorrectly as a result.
This icon indicates that death or serious injury can result if the information is ignored.
This icon indicates that personal injury or material damage can result if
CAUTION
the information is ignored.
WARNING
The icons shown below are used to indicate the nature of the instructions which are to be
observed.
Triangular icons tell you that this information requires attention (“Important”).
Circular icons with a diagonal bar tell you that the action indicated is prohibited
(“Prohibited”).
Filled circles with an exclamation mark indicate an action that must be performed
(“Required”).
WARNING
Do not use in
the bathroom or
shower
Do not disassemble
Do not touch
internal parts
viii
Do not immerse in or expose to water. Failure to observe this precaution can cause
a fire or electric shock.
Do not disassemble (do not open the case). Failure to observe this precaution can
cause fire, electric shock, or injury due to product malfunction.
Should the case break open as the result of a fall or other accident, do not touch the
exposed parts. Failure to observe this precaution could result in electric shock
or in injury from touching the damaged parts. Remove the camera battery
immediately, taking care to avoid injury or electric shock, and take the product
to the point of purchase for consultation.
WARNING
Do not place on unstable surfaces. The product may fall, causing injury.
Do not view the sun through the lens or camera viewfinders. Failure to observe this
precaution can cause permanent visual impairment.
CAUTION
Do not use or store in locations that are exposed to steam, or smoke or are very humid
or extremely dusty. Failure to observe this precaution can cause fire or electric
shock.
Do not leave in direct sunlight or in locations subject to very high temperatures, such
as in a closed vehicle on a sunny day. Failure to observe this precaution can cause
fire.
Keep out of the reach of small children. This product could cause injury in the
hands of a child.
Do not handle with wet hands. Failure to observe this precaution can cause
electric shock.
Keep the sun out of the frame when shooting backlit subjects. Sunlight focused into
the camera when the sun is in or close to the frame can cause fire or burns.
When the product is not in use, replace the lens caps and store out of direct sunlight.
Sunlight focused by the lens can cause fire or burns.
Do not carry the camera or lens while they are attached to a tripod. The product can
fall or strike other objects, causing injury.
For Your Safety
European Union regulatory notice
This product complies with the following EU Directives:
• RoHS Directive 2011/65/EU
• R & TTE Directive 1999/5/EC
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and
wireless transmitters. It also operates on the same frequency as licensed transmitters and
special unlicensed low-voltage transmitters used in RFID tracking systems for assembly
lines and in other similar applications.
Compliance with these directives implies conformity to applicable harmonized European
•
To prevent interference with the above devices, observe the following precautions. Confirm that
standards (European Norms) which are listed on the EU Declaration of Conformity issued by
the RFID transmitter is not in operation before using this device. Should you observe that
FUJIFILM Corporation for this product or product family.
the device causes interference in licensed transmitters used for RFID tracking, immediThis compliance is indicated by the following conformity marking placed on the product:
ately stop using the affected frequency or move the device to another location. If you
notice that this device causes interference in low-voltage RFID tracing systems, contact a
FUJIFILM representative.
This marking is valid for non-Telecom products and EU harmonized Telecom products (e.g.
Bluetooth).
Regarding the Declaration of Conformity, visit http://www.fujifilm.com/products/digital_
cameras/x/fujifilm_x_pro2/pdf/index/fujifilm_x_pro2_cod.pdf.
2.4DS/OF4
This sticker indicates that this device operates in the 2.4 GHz
band using DSSS and OFDM modulation and may cause interference at distances of up to 40 m.
IMPORTANT: Read the following notices before using the camera’s built-in wireless
transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and may not be exported
or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring a high degree of reliability,
for example in medical devices or other systems that may directly or indirectly impact
human life. When using the device in computer and other systems that demand a greater
degree of reliability than wireless networks, be sure to take all necessary precautions to
ensure safety and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations
governing wireless network devices in the country in which it was purchased. Observe all
location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted
over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic fields, static electricity, or radio interference.
Do not use the transmitter in the vicinity of microwave ovens or in other locations subject
to magnetic fields, static electricity, or radio interference that may prevent reception of
wireless signals. Mutual interference may occur when the transmitter is used in the vicinity
of other wireless devices operating in the 2.4 GHz band.
• The wireless transmitter operates in the 2.4 GHz band using DSSS and OFDM modulation.
ix
About This Manual
Before using the camera, read this manual and the warnings in “For Your Safety” (P ii). For information
on specific topics, consult the sources below.
Table of Contents ................................................ P xiii
The “Table of Contents” gives an overview of the
entire manual. The principal camera operations
are listed here.
Troubleshooting ................................................P
................................................ P 151
Having a specific problem with the camera?
Find the answer here.
Warning Messages and Displays .........................P
......................... P 156
Find out what’s behind that flashing icon or error
message in the display.
Restrictions on Camera Settings ..........................P
.......................... P 167
See page 167 for restrictions on the options available in each shooting mode.
Memory Cards
Pictures are stored on optional SD, SDHC, and SDXC memory cards (P 24), referred to in this manual as “memory
cards.”
x
Product Care
Camera body: For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body
after each use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform
the leather on the camera body. Any liquid on the camera should be removed immediately with a
soft, dry cloth. Use a blower to remove dust from the monitor, taking care to avoid scratches, and then
gently wipe with a soft, dry cloth. Any remaining stains can be removed by wiping gently with a piece
of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning fluid has been applied. To
prevent dust entering the camera, replace the body cap when no lens is in place.
Image sensor: Dust can be removed from the image sensor using the D USER SETTING > SENSOR
CLEANING (P 115) option in the camera menus.
Interchangeable lenses: Use a blower to remove dust, then gently wipe with a soft, dry cloth. Any remaining stains can be removed by wiping gently with a piece of FUJIFILM lens-cleaning paper to which a
small amount of lens-cleaning fluid has been applied. Replace the front and rear caps when the lens
is not in use.
xi
Product Features
Frequently-used options can be added to the Q menu or a custom “my” menu or assigned to an Fn
(function) button for direct access. Customize camera controls to suit your style or situation.
The Q Menu (P
(P 47)
The Q menu is displayed by pressing the Q button.
SELECT CUSTOM SETTING
The Function Buttons (P
(P 50)
Use the function buttons for direct access to selected features.
BASE
32
27
23
SET
18
Use the Q menu to view or change the options
selected for frequently-used menu items.
“My Menu” (P
(P 105)
Add frequently-used options to this custom
menu, which can be viewed by pressing MENU/OK
and selecting the E (“MY MENU”) tab.
MY MENU
SELF-TIMER
INTERVAL TIMER SHOOTING
FILM SIMULATION BKT
PHOTOMETRY
SHUTTER TYPE
IS MODE
FACE/EYE DETECTION SETTING
ISO AUTO SETTING
EXIT
R The E tab is only available if options have been assigned to “MY MENU”.
xii
Press the button for direct access to the assigned function.
The illustration shows the Fn2 button being used to display the
bright frame simulation.
Table of Contents
For Your Safety .....................................................................................ii
IMPORTANT SAFETY INSTRUCTIONS.........................................ii
Safety Notes .......................................................................................iii
NOTICES ...............................................................................................vi
Safety Notes .....................................................................................viii
About This Manual .............................................................................x
Product Care ........................................................................................xi
Product Features...............................................................................xii
The Q Menu .......................................................................................xii
“My Menu” .........................................................................................xii
The Function Buttons ....................................................................xii
Before You Begin
Symbols and Conventions..............................................................1
Supplied Accessories ........................................................................1
Parts of the Camera ...........................................................................2
The Selector ........................................................................................4
The Focus Stick (Focus Lever).......................................................4
The Shutter-Speed/ISO Dial ..........................................................4
The Front Command Dial...............................................................5
The Rear Command Dial ................................................................6
The Indicator Lamp ..........................................................................7
Camera Displays ................................................................................8
Shooting: Optical Viewfinder ....................................................8
Shooting: Electronic Viewfinder/LCD Monitor ................ 10
Playback.......................................................................................... 12
Lenses ................................................................................................... 13
Parts of the Lens ............................................................................. 13
Removing the Caps ....................................................................... 13
Attaching the Hood ...................................................................... 13
Lenses with Aperture Rings ....................................................... 14
Lenses with No Aperture Rings ................................................ 14
Lenses with O.I.S. Switches......................................................... 15
Manual Focus Lenses.................................................................... 15
First Steps
Attaching the Strap ........................................................................ 16
Attaching a Lens .............................................................................. 18
Charging the Battery ..................................................................... 19
Inserting the Battery...................................................................... 20
Inserting Memory Cards............................................................... 22
Using Two Cards ............................................................................. 23
Compatible Memory Cards ..................................................... 24
Turning the Camera on and Off ................................................ 25
Basic Setup ......................................................................................... 26
Changing Basic Settings ............................................................. 27
Display Settings ............................................................................... 28
Choosing a Display........................................................................ 28
The Viewfinder Selector .............................................................. 29
Bright Frame Simulation ............................................................. 30
The Viewfinder Display ................................................................ 31
Focusing the Viewfinder ............................................................. 31
Adjusting Display Brightness .................................................... 31
The DISP/BACK Button ....................................................................... 32
Shooting: Optical Viewfinder ................................................. 32
Shooting: Electronic Viewfinder............................................ 32
LCD Monitor: Shooting ............................................................. 32
Customizing the Standard Display ...................................... 33
Viewfinder/LCD Monitor: Playback ...................................... 34
xiii
Table of Contents
Basic Photography and Playback
More on Photography and Playback
Program AE (P) .................................................................................. 35
Shutter-Priority AE (S) ................................................................... 36
Aperture-Priority AE (A) ............................................................... 37
Manual Exposure (M) ..................................................................... 38
Viewing Pictures .............................................................................. 39
Viewing Pictures Full Frame....................................................... 39
Viewing Photo Information ....................................................... 40
Playback Zoom ............................................................................... 41
Multi-Frame Playback................................................................... 42
Deleting Pictures ............................................................................. 43
Drive Mode ......................................................................................... 53
R Burst Mode (CONTINUOUS) ................................................. 54
Bracketing ......................................................................................... 55
Y Advanced Filters...................................................................... 56
j Multiple Exposures.................................................................. 57
Exposure Compensation .............................................................. 58
C (Custom) ..................................................................................... 58
Sensitivity ........................................................................................... 59
Metering .............................................................................................. 60
Film Simulation ................................................................................ 61
White Balance ................................................................................... 62
Focus Mode ........................................................................................ 64
The Focus Indicator .................................................................... 65
MF Assist ......................................................................................... 66
Autofocus Options (AF Mode) .................................................. 67
Focus-Point Selection................................................................... 68
The Focus Point Display .............................................................. 69
Single Point AF ............................................................................. 69
Zone AF ........................................................................................... 70
Tracking (Focus Mode C Only) ................................................ 71
Long Time-Exposures (T/B) ......................................................... 72
Time (T) .............................................................................................. 72
Bulb (B) ............................................................................................... 72
Using a Remote Release .............................................................. 73
Basic Movie Recording and Playback
Recording Movies............................................................................ 44
Using an External Microphone ................................................. 45
Viewing Movies ................................................................................ 46
The Q (Quick Menu) Button
Using the Q Button ......................................................................... 47
The Quick Menu Display ............................................................. 47
Viewing and Changing Settings .............................................. 48
Editing the Quick Menu .............................................................. 49
The Fn (Function) Buttons
Using the Function Buttons ........................................................ 50
Assigning Roles to the Function Buttons ............................. 51
TTL-LOCK ........................................................................................ 52
MODELING FLASH ...................................................................... 52
xiv
Table of Contents
The Self-Timer ................................................................................... 74
Interval Timer Photography ....................................................... 75
Focusing and Taking Pictures .................................................... 76
Focus/Exposure Lock ..................................................................... 77
Flash Photography.......................................................................... 79
Recording Pictures in RAW Format ......................................... 81
Creating JPEG Copies of RAW Pictures .................................. 82
Saving Settings................................................................................. 83
Using a Mount Adapter ................................................................ 84
Bright Frame Brightness.............................................................. 84
Lens Registration............................................................................ 84
Choosing a Focal Length ......................................................... 84
Distortion Correction ................................................................ 84
Color Shading Correction ........................................................ 85
Peripheral Illumination Correction ...................................... 85
PhotoBook Assist............................................................................. 86
Creating a PhotoBook .................................................................. 86
Viewing Photobooks .................................................................... 87
Editing and Deleting Photobooks........................................... 87
Menus
Using the Menus: Shooting Mode ........................................... 88
Using the Shooting Menu .......................................................... 88
H IMAGE QUALITY SETTING ...................................................... 89
IMAGE SIZE .................................................................................... 89
IMAGE QUALITY ........................................................................... 89
RAW RECORDING ........................................................................ 90
FILM SIMULATION ....................................................................... 90
GRAIN EFFECT .............................................................................. 90
DYNAMIC RANGE ........................................................................ 90
WHITE BALANCE .......................................................................... 90
HIGHLIGHT TONE ........................................................................ 91
SHADOW TONE ............................................................................ 91
COLOR ............................................................................................. 91
SHARPNESS ................................................................................... 91
NOISE REDUCTION ..................................................................... 91
LONG EXPOSURE NR .................................................................. 91
LENS MODULATION OPTIMIZER............................................ 91
COLOR SPACE................................................................................ 91
PIXEL MAPPING............................................................................ 92
SELECT CUSTOM SETTING ....................................................... 92
EDIT/SAVE CUSTOM SETTING................................................. 92
xv
Table of Contents
G AF/MF SETTING ......................................................................... 93
FOCUS AREA ................................................................................. 93
AF MODE ........................................................................................ 93
AF-C CUSTOM SETTINGS.......................................................... 94
AF POINT DISPLAY y z ......................................................... 94
NUMBER OF FOCUS POINTS ................................................... 94
PRE-AF ............................................................................................. 95
AF ILLUMINATOR ......................................................................... 95
FACE/EYE DETECTION SETTING ............................................. 95
AF+MF ............................................................................................. 96
MF ASSIST ...................................................................................... 96
FOCUS CHECK .............................................................................. 96
INTERLOCK SPOT AE & FOCUS AREA ................................... 96
INSTANT AF SETTING ................................................................. 96
DEPTH-OF-FIELD SCALE ........................................................... 97
RELEASE/FOCUS PRIORITY ...................................................... 97
CORRECTED AF FRAME ............................................................. 97
A SHOOTING SETTING ................................................................ 98
SELF-TIMER .................................................................................... 98
INTERVAL TIMER SHOOTING ................................................... 98
AE BKT ............................................................................................. 98
FILM SIMULATION BKT .............................................................. 98
PHOTOMETRY ............................................................................... 98
SHUTTER TYPE.............................................................................. 99
IS MODE .......................................................................................... 99
ISO AUTO SETTING ...................................................................100
MOUNT ADAPTOR SETTING..................................................100
WIRELESS COMMUNICATION ...............................................100
xvi
F FLASH SETTING .......................................................................101
FLASH FUNCTION SETTING...................................................101
RED EYE REMOVAL....................................................................101
TTL-LOCK MODE ........................................................................102
LED LIGHT SETTING..................................................................102
MASTER SETTING ......................................................................103
CH SETTING .................................................................................103
B MOVIE SETTING .......................................................................104
MOVIE MODE ..............................................................................104
MIC LEVEL ADJUSTMENT .......................................................104
MIC/REMOTE RELEASE ............................................................104
E MY MENU ...................................................................................105
Using the Menus: Playback Mode..........................................106
Using the Playback Menu .........................................................106
C PLAY BACK MENU ...................................................................107
SWITCH SLOT ..............................................................................107
RAW CONVERSION....................................................................107
ERASE .............................................................................................107
CROP ..............................................................................................107
RESIZE ............................................................................................108
PROTECT .......................................................................................108
IMAGE ROTATE............................................................................108
RED EYE REMOVAL....................................................................109
VOICE MEMO SETTING ............................................................110
COPY ..............................................................................................111
WIRELESS COMMUNICATION ...............................................111
SLIDE SHOW ................................................................................111
PHOTOBOOK ASSIST ................................................................111
PC AUTO SAVE ............................................................................112
PRINT ORDER (DPOF)...............................................................112
instax PRINTER PRINT ..............................................................112
DISP ASPECT ...............................................................................112
Table of Contents
The Setup Menu .............................................................................113
Using the Setup Menu ...............................................................113
D SET UP Menu Options ...........................................................114
D USER SETTING .......................................................................114
FORMAT ........................................................................................114
DATE/TIME ...................................................................................114
TIME DIFFERENCE .....................................................................115
a .....................................................................................115
MY MENU SETTING...................................................................115
SENSOR CLEANING...................................................................115
RESET .............................................................................................115
D SOUND SETTING ..................................................................116
AF BEEP VOL. ...............................................................................116
SELF-TIMER BEEP VOL. .............................................................116
OPERATION VOL. .......................................................................116
SHUTTER VOLUME ....................................................................116
SHUTTER SOUND ......................................................................116
PLAYBACK VOLUME..................................................................116
D SCREEN SETTING ..................................................................117
EVF BRIGHTNESS .......................................................................117
EVF COLOR ...................................................................................117
LCD BRIGHTNESS.......................................................................117
LCD COLOR ..................................................................................117
IMAGE DISP. .................................................................................117
EVF AUTOROTATE DISPLAYS .................................................117
PREVIEW EXP./WB IN MANUAL MODE...............................117
PREVIEW PIC. EFFECT...............................................................118
FRAMING GUIDELINE...............................................................118
AUTOROTATE PB ........................................................................118
FOCUS SCALE UNITS ................................................................118
DISP. CUSTOM SETTING ..........................................................118
D BUTTON/DIAL SETTING .....................................................119
FOCUS LEVER SETTING ...........................................................119
EDIT/SAVE QUICK MENU ........................................................119
FUNCTION (Fn) SETTING ........................................................119
COMMAND DIAL SETTING .....................................................119
Y X S.S OPERATION ................................................................119
ISO DIAL SETTING (H) ..............................................................119
ISO DIAL SETTING (L) ...............................................................119
SHOOT WITHOUT LENS...........................................................119
SHOOT WITHOUT CARD .........................................................120
FOCUS RING ................................................................................120
AE-L/AF-L BUTTON SETTING ................................................120
AE/AF-LOCK MODE...................................................................120
AF-LOCK MODE..........................................................................120
APERTURE SETTING..................................................................120
D POWER MANAGEMENT .....................................................121
AUTO POWER OFF ....................................................................121
POWER MANAGEMENT...........................................................121
AUTO POWER SAVE ..................................................................121
D SAVE DATA SETTING ...........................................................122
FRAME NO. ...................................................................................122
SAVE ORG IMAGE ......................................................................122
EDIT FILE NAME .........................................................................122
CARD SLOT SETTING (STILL IMAGE) ...................................123
SWITCH SLOT (SEQUENTIAL) ................................................123
COPYRIGHT INFO ......................................................................123
D CONNECTION SETTING......................................................124
WIRELESS SETTINGS.................................................................124
PC AUTO SAVE SETTING .........................................................124
GEOTAGGING SET-UP ..............................................................124
instax PRINTER CONNECTION SETTING ...........................124
xvii
Table of Contents
“My Menu” ........................................................................................125
Editing “My Menu” .......................................................................125
Factory Defaults .............................................................................126
Connections
Wireless Transfer (FUJIFILM Camera Remote/
FUJIFILM PC AutoSave) ...............................................................129
Wireless Connections: Smartphones ...................................129
Wireless Connections: Computers ........................................129
Viewing Pictures on a Computer (MyFinePix Studio/
RAW FILE CONVERTER EX 2.0)..................................................130
Windows ..........................................................................................130
Mac OS X/macOS .........................................................................130
Connecting the Camera ............................................................131
Creating a DPOF Print Order ....................................................133
WITH DATE s/ WITHOUT DATE ..........................................133
RESET ALL.....................................................................................134
instax SHARE Printers ..................................................................135
Establishing a Connection........................................................135
Printing Pictures ...........................................................................136
Viewing Pictures on TV ...............................................................137
xviii
Technical Notes
Optional Accessories....................................................................138
Accessories from FUJIFILM .......................................................138
Connecting the Camera to Other Devices .........................142
Using Shoe-Mounted Flash Units..........................................143
Caring for the Camera .................................................................149
Use and Storage Precautions ..................................................149
Traveling ..........................................................................................149
Cleaning the Image Sensor .......................................................150
Troubleshooting
Problems and Solutions .............................................................151
Warning Messages and Displays ............................................156
Appendix
Memory Card Capacity ...............................................................159
Links.....................................................................................................160
FUJIFILM X-Pro2 Product Information .................................160
Firmware Updates .......................................................................160
Specifications ..................................................................................161
Restrictions on Camera Settings ............................................167
Before You Begin
Symbols and Conventions
Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may
be simplified for explanatory purposes.
Supplied Accessories
Before You Begin
The following symbols are used in this manual:
Q This information should be read before use to ensure correct operation.
R Additional information that may be helpful when using the camera.
POther pages in this manual on which related information may be found.
The following items are included with the camera:
NP-W126/NP-W126S rechargeable battery
Clip attaching tool
BC-W126 battery charger
Metal strap clips (× 2)
Body cap
• Protective covers (× 2)
• Shoulder strap
• Hot shoe cover
(comes attached to hot shoe)
• Sync terminal cap
(comes attached to camera)
• Owner’s Manual (this manual)
1
Parts of the Camera
For more information, refer to the page listed to the right of each item.
2
Parts of the Camera
i Memory card slot cover.....................................22
j Cable channel cover for DC coupler .................138
k Battery-chamber cover latch ............................20
l Battery-chamber cover .....................................20
m Speaker.............................................................46
n Tripod mount
o Indicator lamp ....................................................7
p LCD monitor .......................................... 10, 28, 32
q DISP (display)/BACK button ............................32
Function button role selection (press and hold)
.........................................................................51
r b (delete) button ........................................ 6, 43
s a (playback) button ......................................39
t Body cap ...........................................................18
u Memory card slot 2 ...........................................22
v Memory card slot 1 ...........................................22
w Battery latch .....................................................20
x Battery chamber ...............................................20
Before You Begin
A Movie-record button.........................................44 S Front command dial ...........................................5
Function button (Fn1) ......................................50 T ON/OFF switch .................................................25
B Shutter button ..................................................76 U Hot shoe cover ..................................................79
C Exposure compensation dial .............................58 V Micro HDMI connector ....................................137
D Shutter speed dial/Sensitivity dial
W Micro USB connector.......................................131
....................................................4, 35, 36, 37, 38 X Microphone/remote release connector ....... 45, 73
E Dial lock release ...................................... 4, 36 ,38 Y Eye sensor .........................................................28
F AF-assist illuminator.........................................95 Z VIEW MODE button .........................................28
Self-timer lamp ................................................74 a Metering button ...............................................60
Function button (Fn3) ......................................50
G Hot shoe ..................................................... 79, 80
H Microphone ......................................................45 b AE-L (exposure lock) button ..................... 77, 120
I Viewfinder window ................................ 8, 28, 32 c Focus stick (focus lever) .......................... 4, 68, 69
J Diopter adjustment control...............................31 d Rear command dial.............................................6
K Strap eyelet ......................................................16 e AF-L (focus lock) button ..................... 64, 77, 120
L Sync terminal....................................................80 f Q (quick menu) button * ....................................47
Quick menu edit/custom settings button
M Connector cover ...........................45, 73, 131, 137
(press and hold) * ..............................................49
N Focus mode selector .........................................64
RAW conversion button (playback mode) .........82
O Lens signal contacts ..........................................13
P Lens release button ..........................................18 g Selector ........................................................ 4, 26
Function buttons ..............................................50
Q Viewfinder selector ..................................... 29, 30
R Bright frame simulation display button ............30 h MENU/OK button ............................. 88, 106, 113
Function button (Fn2) ......................................50
X (control lock) button (press and hold) ........11
* In shooting mode, press and release to display quick menu or press and hold to display quick menu edit options. When quick
menu is displayed, press and hold to edit custom settings.
Control Lock
To prevent accidental operation of the selector and Q button during shooting, press MENU/OK until X is displayed. The controls can be unlocked by pressing MENU/OK until X is no longer displayed.
3
Parts of the Camera
The Selector
Press the selector up (q), right (e), down (r), or
left (w) to highlight items. The up, left, right, and
down buttons also double as the DRIVE (P 53), Fn4
(film simulation; P 61), Fn5 (white balance; P 62),
and Fn6 (AF mode; P 67) buttons, respectively
(P 50).
The Shutter-Speed/ISO Dial
Choose a shutter speed and ISO sensitivity.
Rotate the dial to choose a shutter
speed (P 35, 36, 37, 38).
R If the dial is in the A position, press
the lock release while rotating the
dial.
The Focus Stick (Focus Lever)
Tilt or press the focus stick to select the focus
area (P 68).
4
Lift and rotate the dial to choose ISO
sensitivity (P 59).
Parts of the Camera
The Front Command Dial
The front command dial is used as described below.
Before You Begin
■ Rotate
• Choose the desired combination of shutter speed and aperture (program shift; P 35).
• Choose a shutter speed (P 36, 38).
• Adjust exposure compensation when C is selected with exposure compensation dial (P 58).
• View other pictures during playback (P 39).
■ Press
Press the center of the dial to switch back and forth between shutter speed and exposure
compensation when C is selected with the exposure compensation dial (P 35, 36, 38, 58).
5
Parts of the Camera
The Rear Command Dial
The rear command dial is used as described below.
■ Rotate
• Adjust aperture (P 14, 37, 38).
• Adjust settings in the quick menu (P 48).
• Choose the size of the focus frame (P 69, 70)
• Zoom in or out during focus zoom or in full frame or multi-frame playback (P 41, 42).
■ Press
• Perform the function assigned to the DIAL function button (P 51).
• In manual focus mode, you can choose a focus display by pressing and holding the center
of the dial (P 66).
• Zoom in on the active focus point during playback (P 40).
Formatting Memory Cards
To format memory cards, press the center of the command dial while pressing and holding the b button. The
FORMAT menu will be displayed; select a slot and format the card as described on page 114.
6
Parts of the Camera
The Indicator Lamp
When the viewfinder is not in use (P 28), the indicator lamp shows camera status.
Indicator lamp
Before You Begin
Indicator lamp
Camera status
Glows green
Focus locked.
Blinks green
Focus or exposure warning. Pictures can be taken.
Blinks green and orange Recording pictures. Additional pictures can be taken.
Recording pictures. No additional pictures can be taken at this
Glows orange
time.
Blinks orange
Flash charging; flash will not fire when picture is taken.
Blinks red
Lens or memory error.
R Warnings may also appear in the display (P 156).
7
Parts of the Camera
Camera Displays
The following types of indicator may be displayed during shooting and playback. In the description that
follows, all available indicators are shown for illustrative purposes; the indicators actually displayed vary
with camera settings. Note that the LCD monitor and electronic viewfinder have different aspect ratios.
■ Shooting: Optical Viewfinder
3
2
1
0
-1
-2
-3
8
Parts of the Camera
N Virtual horizon ..................................................34
O Distance indicator .............................................64
P Sensitivity.........................................................59
Q Exposure compensation ....................................58
R Aperture ............................................... 35, 37, 38
S Shutter speed ....................................... 35, 36, 38
T AE lock indicator ...............................................77
U Metering...........................................................60
V Shooting mode ................................35, 36, 37, 38
W Focus indicator..................................................65
X Manual focus indicator .....................................65
Y Focus mode ......................................................64
Z Histogram.........................................................34
a Dynamic range .................................................90
b Film simulation.................................................61
c White balance...................................................62
d Exposure indicator ...................................... 38, 58
e AF+MF indicator ..............................................96
f Shutter type......................................................99
g Continuous mode ....................................... 53, 54
h Self-timer indicator ..........................................74
i Microphone/remote release ............... 45, 73, 104
j Flash (TTL) mode ............................................101
Before You Begin
A IS mode ............................................................99
B Control lock.........................................................3
C Depth-of-field preview .....................................37
D Location data download status .......................124
E Movie mode.............................................. 44, 104
F Time remaining ................................................44
G Card slot options ....................................... 23, 123
H Number of available frames * .........................159
I Image quality and size ......................................89
J Battery level .....................................................25
K Bright frame .....................................................30
L Focus frame .......................................... 68, 76, 77
M Temperature warning .....................................158
Flash compensation ........................................101
* Shows “9999” if there is space for over 9999 frames.
9
Parts of the Camera
■ Shooting: Electronic Viewfinder/LCD Monitor
12/31/2050 10:00 AM
10
Parts of the Camera
N Temperature warning .....................................158
O Control lock.........................................................3
P Virtual horizon ..................................................34
Q Histogram.........................................................34
R Distance indicator .............................................64
S Battery level .....................................................25
T Sensitivity.........................................................59
U Exposure compensation ....................................58
V Aperture ............................................... 35, 37, 38
W Shutter speed ....................................... 35, 36, 38
X AE lock indicator ...............................................77
Y Metering...........................................................60
Z Shooting mode ................................35, 36, 37, 38
a Focus indicator..................................................65
b Manual focus indicator .....................................65
c Focus mode ......................................................64
d AF+MF indicator ..............................................96
e Shutter type......................................................99
f Continuous mode ....................................... 53, 54
g Exposure indicator ...................................... 38, 58
h Self-timer indicator ..........................................74
i Microphone/remote release ............... 45, 73, 104
j Flash (TTL) mode ............................................101
Flash compensation ........................................101
k IS mode ............................................................99
Before You Begin
A Focus check.......................................................65
B Depth-of-field preview .....................................37
C Location data download status .......................124
D Movie mode.............................................. 44, 104
E Time remaining ................................................44
F Card slot options ....................................... 23, 123
G Number of available frames * .........................159
H Image quality and size ......................................89
I Date and time ............................................. 26, 27
J Focus frame .......................................... 68, 76, 77
K White balance...................................................62
L Film simulation.................................................61
M Dynamic range .................................................90
* Shows “9999” if there is space for over 9999 frames.
Control Lock
X
Pressing a locked control (P
(P 3) displays a X icon.
11
Parts of the Camera
■ Playback
12/31/2050 10:00 AM
A Date and time ............................................. 26, 27
B Face detection indicator....................................95
C Red-eye removal indicator..............................109
D Advanced filter .................................................56
E Location data ..................................................124
F Protected image .............................................108
G Card slot.................................................... 39, 107
H Frame number ................................................122
12
I Gift image.........................................................39
J Photobook assist indicator ................................86
K DPOF print indicator .......................................133
L Battery level .....................................................25
M Image size/quality ............................................89
N Film simulation.................................................61
O Dynamic range .................................................90
P White balance...................................................62
Q Sensitivity.........................................................59
R Exposure compensation ....................................58
S Aperture ............................................... 35, 37, 38
T Shutter speed ....................................... 35, 36, 38
U Playback mode indicator...................................39
V Movie icon ........................................................46
W Rating ...............................................................39
Lenses
The camera can be used with lenses for the FUJIFILM X-mount.
Parts of the Lens
Before You Begin
Removing the Caps
Remove the caps as shown.
Q Lens caps may differ from those shown.
A Lens hood
B Mounting marks
C Focus ring
D Zoom ring
E Aperture ring
F O.I.S. switch
G Aperture mode switch
H Lens signal contacts
I Front lens cap
J Rear lens cap
Attaching the Hood
When attached, lens hoods reduce glare and protect the front lens element.
13
Lenses
Lenses with Aperture Rings
At settings other than A, you
can adjust aperture by rotating the lens aperture ring (exposure modes A and M).
Aperture ring
A 16 11 8 5.6 4 2.8
A 16 11 8 5.6 4
Lenses with No Aperture Rings
The method used to adjust aperture can be
selected using D BUTTON/DIAL SETTING >
APERTURE SETTING (P 120). When an option
other than AUTO is selected, aperture can be
adjusted using the rear command dial.
The Aperture Mode Switch
If the lens has an aperture mode switch, aperture can
be adjusted manually by sliding the switch to Z and
rotating the aperture ring.
Aperture ring
R Aperture control defaults to the rear command dial,
but can be reassigned to the front command dial
using D BUTTON/DIAL SETTING > COMMAND
DIAL SETTING (P 119).
Aperture mode switch
Q When the aperture ring is set to A, rotate the rear
command dial to adjust aperture.
14
Lenses
O.I.S. switch
Manual Focus Lenses
Slide the focus ring to the front for
autofocus.
For manual focus, slide the focus ring
to the back and rotate it while checking the results in the camera display.
The focus distance and depth-of-field
indicators can be used to assist manual focus. Note that manual focus may
not be available in all shooting modes.
Before You Begin
Lenses with O.I.S. Switches
If the lens supports optical image stabilization
(O.I.S.), the image stabilization mode can be chosen in the camera menus. To activate image stabilization, slide the O.I.S. switch to ON.
The Depth-of-Field Indicator
The depth-of-field indicator shows the approximate
depth of field (the distance in front of and behind the
focus point that appears to be in focus).
Distance indicator
R The indicator is displayed in film format (P 37).
15
First Steps
Attaching the Strap
Attach the strap clips to the camera and then attach the strap.
1 Open a strap clip.
Use the clip attaching tool to open a strap clip,
making sure that the tool and clip are in the
orientations shown.
3 Pass the clip through the eyelet.
Rotate the clip fully through
the eyelet until it clicks
closed.
4 Attach a protective cover.
Q Keep the tool in a safe place. You will need it to
open the strap clips when removing the strap.
2 Place the strap clip on an eyelet.
Hook the strap eyelet in the clip opening. Remove the tool, using the other hand to keep
the clip in place.
16
Place a protective cover over the eyelet as
shown, with the black side of the cover toward
the camera. Repeat Steps 1–4 for the second
eyelet.
Attaching the Strap
5 Insert the strap.
Insert the strap through a protective cover
and strap clip.
6 Fasten the strap.
Fasten the strap as shown. Repeat Steps 5–6
for the second eyelet.
First Steps
Q To avoid dropping the camera, be sure the strap is
correctly secured.
17
Attaching a Lens
Lenses attach as described below.
Q Care is required to prevent dust or other particles from entering the camera while attaching and removing lenses.
1 Remove the body and rear caps.
Remove the body cap from the camera and
the rear cap from the lens.
Removing Lenses
To remove the lens, turn the
camera off, then press the lens
release button and rotate the
lens as shown.
Lens release button
Q Do not touch the camera’s internal parts.
2 Attach the lens.
Place the lens on mount, keeping the marks
on the lens and camera aligned, and then rotate the lens until it clicks into place.
Q Do not press the lens release button while attaching the lens.
18
Q To prevent dust accumulating on the lens or inside the
camera, replace the lens caps and camera body cap
when the lens is not attached.
Lenses and Other Optional Accessories
The camera can be used with lenses for the FUJIFILM
X-mount and the other accessories listed from page
138.
Charging the Battery
The battery is not charged at shipment. Before use, charge the battery in the supplied battery charger.
1 Place the battery in the charger.
Place the battery in the supplied battery charger as shown.
Charge lamp
Plug the charger into an indoor power outlet.
The charging indicator will light.
The Charging Indicator
The charging indicator shows battery charge status as follows:
Charging
indicator
Arrow
On
Battery not
inserted.
Battery fully
charged.
Battery charging.
Blinks
Battery fault.
Off
Battery
The camera uses an NP-W126/NP-W126S rechargeable battery.
R The supplied AC cord is for use exclusively with
the supplied battery charger. Do not use the
supplied charger with other cords or the supplied cord with other devices.
Battery status
Action
First Steps
Battery charger
2 Plug the charger in.
Insert the battery.
Remove the battery.
—
Unplug the charger
and remove the
battery.
3 Charge the battery.
Remove the battery when charging is complete. See the specifications (P 165) for charging times (note that charging times increase
at low temperatures).
Q Unplug the charger when it is not in use.
19
Inserting the Battery
After charging the battery, insert the battery in the camera as described below.
1 Open the battery-chamber cover.
Slide the battery-chamber latch as shown and
open the battery-chamber cover.
2 Insert the battery.
Using the battery to keep the battery latch
pressed to one side, insert the battery contacts first in the direction shown by the arrow.
Confirm that the battery is securely latched.
Arrow
Q Do not open the battery-chamber cover when
the camera is on. Failure to observe this precaution could damage image files or memory cards.
Q Do not use excessive force when handling the
battery-chamber cover.
Battery latch
Q Insert the battery in the orientation shown. Do
not use force or attempt to insert the battery upside down or backwards. The battery will slide in
easily in the correct orientation.
3 Close the battery-chamber cover.
20
Inserting the Battery
Battery latch
Q The battery may become hot when used in hightemperature environments. Observe caution when
removing the battery.
Q Batteries
• Remove dirt from the battery terminals with a clean,
dry cloth. Failure to observe this precaution could
prevent the battery from charging.
• Do not affix stickers or other objects to the battery.
Failure to observe this precaution could make it impossible to remove the battery from the camera.
• Do not short the battery terminals. The battery could
overheat.
• Read the cautions in “The Battery and Power Supply”
(P v).
• Use only battery chargers designated for use with the
battery. Failure to observe this precaution could result in product malfunction.
• Do not remove the labels from the battery or attempt
to split or peel the outer casing.
• The battery gradually loses its charge when not in
use. Charge the battery one or two days before use.
First Steps
Removing the Battery
Before removing the battery, turn the camera off and
open the battery-chamber cover.
To remove the battery, press the
battery latch to the side, and
slide the battery out of the camera as shown.
21
Inserting Memory Cards
The camera has no internal memory; instead, pictures are stored on optional SD, SDHC, and SDXC
memory cards (sold separately). The camera can be used with two cards, one in each of its two slots.
Movies are recorded only to the card in the first slot, which supports UHS-II.
Q Be sure card is in the correct orientation; do not
1 Open the memory card slot cover.
insert at an angle or use force.
Q SD/SDHC/SDXC memory cards can be locked,
making it impossible to
format the card or to Write-protect switch
record or delete images.
Before inserting a memory card, slide the writeprotect switch to the unlocked position.
Q Do not open the memory card slot cover when
the camera is on. Failure to observe this precaution could damage image files or memory cards.
2 Insert a memory card.
Holding the memory card in the orientation
shown, slide it in until it clicks into place at the
back of the first slot (if you are using two cards,
insert the second card into second slot).
Click!
22
3 Close the memory card slot cover.
Removing Memory Cards
Before removing memory cards, turn the camera off
and open the memory card slot cover.
To remove a memory card,
press it in and release it slowly.
Press center
of card
The card can then be removed
by hand. When a memory card
is removed, the card could be
ejected too quickly. Use your
finger to hold it and gently release the card.
Inserting Memory Cards
Using Two Cards
At default settings, the card in the second slot is used only if the card in the first slot is full (SEQUENTIAL).
This can be changed using D SAVE DATA SETTING > CARD SLOT SETTING (STILL IMAGE) (P 123).
Option
Description
The card in the second slot is used only when the card in the first slot is full.
R If the second slot is selected for D SAVE DATA SETTING > SWITCH SLOT (SEQUENTIAL), recording will start on the card in the second slot and switch to the first slot when
the card in the second slot is full.
BACKUP
Each picture is recorded twice, once to each card.
RAW/JPEG
As for SEQUENTIAL
SEQUENTIAL, except that the RAW copy of pictures taken with FINE + RAW or NORMAL + RAW selected for H IMAGE QUALITY SETTING > IMAGE QUALITY will be saved to
the card in the first slot and the JPEG copy to the card in the second slot.
First Steps
SEQUENTIAL (default)
Display
Movies
Regardless of the option selected for CARD SLOT SETTING (STILL IMAGE), movies will be recorded to the card
in the first slot; if SEQUENTIAL is selected, movies will be recorded to the card in the first slot even after recording has moved on to the card in the second slot.
23
Inserting Memory Cards
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the camera; UHS-II cards can be used in the first slot. A complete list of approved memory cards is available
at http://www.fujifilm.com/support/digital_cameras/compatibility/. Operation is not guaranteed with
other cards. The camera can not be used with xD-Picture Cards or MultiMediaCard (MMC) devices.
Q Memory Cards
• Do not turn the camera off or remove the memory card while the memory card is being formatted or data are
being recorded to or deleted from the card. Failure to observe this precaution could damage the card.
• Format memory cards before first use, and be sure to reformat all memory cards after using them in a computer
or other device. For more information on formatting memory cards, see page 114.
• Memory cards are small and can be swallowed; keep out of reach of children. If a child swallows a memory card,
seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions of an SD/SDHC/SDXC card
may not eject normally; if the card does not eject, take the camera to an authorized service representative. Do
not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of SD/SDHC/SDXC memory card. Use a UHS speed class 1
card or better for movies and burst photography.
• Formatting a memory card in the camera creates a folder in which pictures are stored. Do not rename or delete
this folder or use a computer or other device to edit, delete, or rename image files. Always use the camera to
delete pictures; before editing or renaming files, copy them to a computer and edit or rename the copies, not
the originals. Renaming the files on the camera can cause problems during playback.
24
Turning the Camera on and Off
Rotate the ON/OFF switch to ON to turn the camera on. Select OFF
to turn the camera off.
Q Fingerprints and other marks on the lens or viewfinder can affect pictures or the view through the viewfinder.
Keep the lens and viewfinder clean.
First Steps
R Press the a button to start playback. Press the shutter button halfway to return to shooting mode.
R The camera will turn off automatically if no operations are performed
for the length of time selected for D POWER MANAGEMENT >
AUTO POWER OFF (P 121). To reactivate the camera after it has turned off automatically, press the shutter button halfway or turn the ON/OFF switch to OFF and then back to ON.
Battery Level
After turning the camera on, check the battery level in the display.
Indicator
e
f
g
h
i
i (red)
j (blinks red)
Description
Battery partially discharged.
Battery about 80% full.
Battery about 60% full.
Battery about 40% full.
Battery about 20% full.
Low battery. Charge as soon as possible.
Battery exhausted. Turn camera off and recharge battery
25
Basic Setup
A language-selection dialog is displayed the first time the camera is turned on.
1 Choose a language.
Highlight a language and press MENU/OK.
R Press DISP/BACK to skip the current step. Any steps you skip will be displayed the next time the
camera is turned on.
2 Set the date and time.
DATE/TIME NOT SET
2018
Y Y .MM.DD
2017
2016
2015
2014
AM
SET
NO
Press the selector left or right to highlight the year, month, day, hour,
or minute and press up or down to change. To change the order in
which the year, month, and day are displayed, highlight the date format and press the selector up or down. Press MENU/OK to exit to shooting mode when settings are complete.
R If the battery is removed for an extended period, the camera clock will be reset and the language-selection
dialog will be displayed when the camera is turned on.
26
Basic Setup
Changing Basic Settings
To change the language or reset the clock:
1 Display the desired option.
Display the setup menu and select D USER SETTING > a to change the language or
DATE/TIME to reset the clock (P 113).
To choose a language, highlight the desired option and press MENU/OK. To set the clock, press the
selector left or right to highlight the year, month, day, hour, or minute and press up or down to
change, then press MENU/OK once the clock has been set to your satisfaction.
First Steps
2 Adjust settings.
27
Display Settings
The camera is equipped with a hybrid optical/electronic viewfinder (OVF/EVF) and an LCD monitor
(LCD).
Choosing a Display
Press the VIEW MODE button to cycle through displays as shown
below.
Option
E EYE SENSOR
VIEWFINDER ONLY
LCD ONLY
VIEWFINDER ONLY + E
E EYE SENSOR + LCD IMAGE DISP.
Description
Automatic display selection using eye sensor.
Viewfinder only.
LCD monitor only.
Viewfinder only; eye sensor turns display on or off.
Putting your eye to the viewfinder during shooting turns the viewfinder on, but the LCD monitor is used for the display of images immediately after shooting.
The Eye Sensor
The eye sensor turns the viewfinder on when you put your eye to the viewfinder and turns
it off when you take your eye away (note that the eye sensor may respond to objects other
than your eye or to light shining directly on the sensor). If automatic display selection is
enabled, the LCD monitor will turn on when the viewfinder turns off.
28
Eye sensor
Display Settings
The Viewfinder Selector
Use the viewfinder selector to switch between the electronic viewfinder
(EVF), the optical viewfinder (OVF), and a dual optical viewfinder/electronic range finder (ERF) display.
First Steps
3
2
1
0
-1
-2
-3
3
2
1
0
-1
-2
-3
P
P
EVF
P
OVF
ERF (dual display)
The OVF Display
Keep the selector pressed up to choose the optical viewfinder display zoom ratio.
29
Display Settings
The Hybrid (EVF/OVF/ERF) Viewfinder
The features of the different displays are described below.
Display
Description
The optical display is sharp and free of blur so that your subject’s expression is always visible. In addition, the
OVF shows the area just outside the frame, making it easier to compose shots on the fly. Because the viewfinder
OVF
window is a slight distance from the lens, the area visible in photographs may however differ slightly from the
display in the viewfinder due to parallax.
The live view display gives you a preview of the final picture (including depth of field, focus, exposure, and white
EVF
balance) with exactly the same frame coverage.
ERF
As for the optical viewfinder but with a focus preview. A magnified view of an area of the frame including the
(dual display) current focus position is shown at the bottom right corner of the display.
Bright Frame Simulation
The angle of view covered by the bright frame in the OVF display varies with the focal length of the
lens. Pressing a function button (by default, Fn2) displays a bright frame simulation that shows the area
covered by the bright frame at different focal lengths.
R Keep the viewfinder selector pressed up to toggle between the bright frames for maximum and minimum
aperture.
90
32
27
23
18
Wide (0.36 ×)
30
60
56
Focal
length
35
Tele (0.6 ×)
Display Settings
The Viewfinder Display
When ON is selected for D SCREEN SETTING >
EVF AUTOROTATE DISPLAYS (P 117), the indicators in the viewfinder automatically rotate to
match camera orientation.
First Steps
Focusing the Viewfinder
The camera is equipped with diopter adjustment
in the range –4 to +2 m–1 to accommodate individual differences in vision. Rotate the diopter
adjustment control until the viewfinder display is
in sharp focus.
Orientation changed from “wide” to “tall”
Diopter adjustment control
Q The display in the LCD monitor is unaffected.
Adjusting Display Brightness
The brightness and hue of the viewfinder and LCD
monitor can be adjusted using the options under
D SCREEN SETTING. Choose EVF BRIGHTNESS
or EVF COLOR to adjust viewfinder brightness or
hue (P 117), LCD BRIGHTNESS or LCD COLOR to
do the same for the LCD monitor (P 117).
31
The DISP/BACK Button
The DISP/BACK button controls the display of indicators in the
viewfinder and LCD monitor.
■ Shooting: Optical Viewfinder
Standard
■ LCD Monitor: Shooting
Information off
Standard
Information off
3
2
1
0
-1
-2
-3
P
■ Shooting: Electronic Viewfinder
Standard
Information off
Info display
P
32
The DISP/BACK Button
■ Customizing the Standard Display
To choose the items shown in the standard display:
1 Display standard indicators.
Press the DISP/BACK button until standard indicators are displayed.
First Steps
2 Select DISP. CUSTOM SETTING.
Select D SCREEN SETTING > DISP. CUSTOM SETTING (P 118) in the setup menu.
3 Choose a display.
Highlight OVF or EVF/LCD and press MENU/OK.
4 Choose items.
Highlight items and press MENU/OK to select or deselect.
Option
FRAMING GUIDELINE
ELECTRONIC LEVEL
FOCUS FRAME
AF DISTANCE INDICATOR
MF DISTANCE INDICATOR
HISTOGRAM
SHOOTING MODE
APERTURE/S-SPEED/ISO
OVF EVF
w w
w w
R R
w w
R R
w w
R R
R R
Option
INFORMATION BACKGROUND
Expo. Comp. (Digit)
Expo. Comp. (Scale)
FOCUS MODE
PHOTOMETRY
SHUTTER TYPE
FLASH
CONTINUOUS MODE
OVF EVF
— R
w w
R
R
R
R
R
R
R
R
R
R
R
R
Option
DUAL IS MODE
WHITE BALANCE
FILM SIMULATION
DYNAMIC RANGE
FRAMES REMAINING
IMAGE SIZE/QUALITY
MOVIE MODE & REC. TIME
BATTERY LEVEL
OVF EVF
R
R
R
R
R
R
R
R
R
R
R
R
w R
R R
5 Save changes.
Press DISP/BACK to save changes.
6 Exit the menus.
Press DISP/BACK as needed to exit the menus and return to the shooting display.
R See page 8 for the locations of these items in the displays.
33
The DISP/BACK Button
Virtual Horizon
Selecting ELECTRONIC LEVEL displays a virtual horizon. The camera is level when the two
lines overlap.
R The virtual horizon may not be displayed if the camera lens is pointed up or down.
■ Viewfinder/LCD Monitor: Playback
Standard
Information off
Info display
12/31/2050 10:00 AM
Favorites
12/31/2050 10:00 AM
102/31/2050 10:00 AM
FAVORITES
Histograms
Histograms show the distribution of tones in the image. Brightness is shown by the horizontal axis, the
number of pixels by the vertical axis.
Shadows
Highlights
Optimal exposure: Pixels are distributed in an even curve throughout the tone range.
Overexposed: Pixels are clustered
on the right side of the graph.
No. of pixels
Pixel brightness
34
Underexposed: Pixels are clustered
on the left side of the graph.
Basic Photography and Playback
Program AE (P)
To allow the camera to adjust both shutter speed and aperture
for optimal exposure, set shutter speed and aperture to A. P will
appear in the display.
Q If the subject is outside the metering range of the camera, the shutter
speed and aperture displays will show “– – –”.
Aperture mode switch
Program Shift
If desired, you can rotate the front command dial to select other combinations of
shutter speed and aperture without altering exposure (program shift). Program
shift is not available if the attached flash supports TTL auto, or if an auto option is
selected for H IMAGE QUALITY SETTING > DYNAMIC RANGE (P 90). To cancel
program shift, turn the camera off.
Shutter speed
Aperture
Basic Photography and Playback
35
Shutter-Priority AE (S)
To adjust shutter speed manually while letting the camera select aperture for optimal exposure, set aperture to A and use the
shutter speed dial (if A is currently selected for shutter speed,
press the dial lock release while rotating the shutter speed dial).
S will appear in the display.
Aperture mode switch
R Shutter speed can also be adjusted in increments of 1/3 EV by rotating
the front command dial. Shutter speed can be adjusted even while
the shutter button is pressed halfway.
Q If the correct exposure can not be achieved at the selected shutter
speed, aperture will be displayed in red when the shutter button is
pressed halfway. Adjust shutter speed until the correct exposure is
achieved.
Q If the subject is outside the metering range of the camera, the aperture display will show “– – –”.
36
Aperture-Priority AE (A)
To adjust aperture manually while letting the camera select shutter speed for optimal exposure, rotate the shutter speed dial to A
and adjust aperture as desired. A will appear in the display.
R Aperture can be adjusted even while the shutter button is pressed
halfway.
Aperture mode switch
Previewing Depth of Field
When L PREVIEW DEPTH OF FIELD is assigned to a function button (P 51),
pressing the button stops aperture down to the selected setting, allowing depth
of field to be previewed in the display.
Depth of field can also be previewed using the depth-of-field indicator in the standard display (P 33). Press DISP/BACK to cycle through display modes until standard
indicators are displayed.
R Use the G AF/MF SETTING > DEPTH-OF-FIELD SCALE option (P 97) to
choose how depth of field is displayed. Choose FILM FORMAT BASIS to
help you make practical assessments of depth of field for pictures that will be
viewed as prints and the like, PIXEL BASIS to help you assess depth of field for
pictures that will be viewed at high resolutions on computers or other electronic displays.
Basic Photography and Playback
Q If the correct exposure can not be achieved at the selected aperture, the shutter speed will be displayed in red when the shutter button is pressed halfway. Adjust aperture until the correct exposure is
achieved.
Q If the subject is outside the metering range of the camera, the shutter
speed display will show “– – –”.
Depth of field
37
Manual Exposure (M)
Exposure can be altered from the value suggested by the camera
by setting both shutter speed and aperture to values other than
A (if A is currently selected for shutter speed, press the dial lock
release while rotating the shutter speed dial). M will appear in
the display.
R Shutter speed can also be adjusted in increments of 1/3 EV by rotating
the front command dial.
Aperture mode switch
Exposure indicator
㹋
Exposure Preview
To preview exposure in the LCD monitor, select an option other than OFF for D SCREEN SETTING > PREVIEW EXP./WB IN
MANUAL MODE (P 117). Select OFF when using the flash or on
other occasions on which exposure may change when the picture is taken.
38
Viewing Pictures
Viewing Pictures Full Frame
Pictures can be viewed in the viewfinder or LCD monitor. When taking important pictures, take a test
shot and check the results.
To view pictures full frame, press a.
100-0001
R Pictures taken using other cameras are marked with a m (“gift image”) icon to warn that they may not display
correctly and that playback zoom may not be available.
Favorites: Rating Pictures
To rate the current picture, press DISP/BACK and press the selector up and down to select from zero to five stars.
Basic Photography and Playback
Additional pictures can be viewed by pressing the selector left or right or rotating the front command
dial. Press the selector or rotate the dial right to view pictures in the order recorded, left to view pictures in reverse order. Keep the selector pressed to scroll rapidly to the desired frame.
Two Memory Cards
If two memory cards are inserted, you can press and hold the a button to choose a card for playback.
R You can also select a card using the C PLAYBACK MENU > SWITCH SLOT option (P 107).
39
Viewing Pictures
Viewing Photo Information
The photo information display changes each
time the selector is pressed up.
Basic data
Info display 1
12/31/2050 10:00 AM
102/31/2050 10:00 AM
LENS
FOCAL LENGTH
COLOR SPACE
LENS MODULATION OPT.
S.S 1/4000
F 5.6
ISO 400
23.0mm
F5.6
23.0mm
sRGB
ON
+21/3
NEXT
Info display 2
40
R Rotate the front command dial to view other images.
Zooming in on the Focus Point
Press the center of the rear command dial to zoom in on the focus
point. Press again to return to fullframe playback.
Viewing Pictures
Playback Zoom
Rotate the rear command dial right to zoom in on the current picture, left to zoom out (to view multiple images, rotate the dial left when the picture is displayed full frame; P 42). When the picture is
zoomed in, the selector can be used to view areas of the image not currently visible in the display. To
exit zoom, press DISP/BACK, MENU/OK, or the center of the rear command dial.
Zoom indicator
R The maximum zoom ratio varies with image size (P 89). Playback zoom is not available with cropped or resized
copies saved at a size of a (P 107, 108).
Basic Photography and Playback
Navigation window shows
portion of image currently
displayed
41
Viewing Pictures
Multi-Frame Playback
To change the number of images displayed, rotate the rear command dial
left when a picture is displayed full frame.
Rotate left to view more images.
100-0001
Rotate right to view fewer images.
Use the selector to highlight images and press MENU/OK to view the highlighted image full frame (to
zoom in on the selected image, rotate the rear command dial right when the picture is displayed full
frame; P 41). In the nine- and hundred-frame displays, press the selector up or down to view more
pictures.
42
Deleting Pictures
To delete individual pictures, multiple selected pictures, or all pictures, press the b button when a
picture is displayed full frame and choose from the options below. Note that deleted pictures can not
be recovered. Copy important pictures to a computer or other storage device before proceeding.
ERASE
FRAME
SELECTED FRAMES
ALL FRAMES
FRAME
SELECTED FRAMES
ALL FRAMES
Description
Press the selector left or right to scroll through pictures and press MENU/OK to delete the current picture
(a confirmation dialog is not displayed).
Highlight pictures and press MENU/OK to select or deselect (pictures in photobooks or print orders are shown
by S). When the operation is complete, press DISP/BACK to display a confirmation dialog, then highlight OK
and press MENU/OK to delete the selected pictures.
A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all unprotected pictures.
Pressing DISP/BACK cancels deletion; note that any pictures deleted before the button was pressed can not
be recovered.
R Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P 108).
R Pictures can also be deleted from the menus using the C PLAY BACK MENU > ERASE option (P 107).
R If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete
the pictures.
Basic Photography and Playback
Option
43
Basic Movie Recording and Playback
Recording Movies
The camera can be used to record short high-definition movies. Sound is recorded in stereo via the
built-in microphone; do not cover the microphone during recording.
Q Movies are recorded to the card in the first slot. Be sure a card is inserted in the first slot before proceeding.
1 Press the movie-record (Fn1) button to start recording.
Recording indicator
Time remaining
2 Press the button again to end recording. Recording ends automatically when the maximum
length is reached or the memory card is full.
44
R Zoom can be adjusted while recording is in progress.
R Frame size and rate can be selected using W MOVIE
SETTING > MOVIE MODE (P 104). Focus mode is selected using the focus mode selector (P 64); for continuous focus adjustment, select C, or choose S and
enable Intelligent Face Detection (P 95). Intelligent
Face Detection is not available in focus mode M.
R During recording, exposure compensation can be
adjusted by up to ±2 EV.
R The indicator lamp lights while movies are being
recorded.
Recording Movies
Q If the lens is equipped with an aperture mode
switch, select the aperture mode before beginning
recording. If an option other than A is selected,
shutter speed and aperture can be adjusted while
recording is in progress.
Q The microphone may pick up lens noise and other
sounds made by the camera during recording.
Q Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
R The dialog shown at right will be
displayed when a microphone is
connected to the microphone/
remote release connector.
Press MENU/OK and select MIC/
REMOTE RELEASE > m MIC.
CHECK MIC/REMOTE RELEASE
SETTING
SKIP
SET
Basic Movie Recording and Playback
Depth of Field
Adjust aperture before recording begins. Choose
low f-numbers to soften background details.
Using an External Microphone
Sound can be recorded with
external microphones that connect using jacks 2.5 mm in diameter; microphones that require
bus power can not be used. See
the microphone manual for details.
45
Viewing Movies
During playback, movies are displayed as shown at right. The following operations
can be performed while a movie is displayed:
12/31/2050 10:00 AM
Operation
Description
Press the selector down to start playback. Press again to pause. While playback is
Start/pause playback paused, you can press the selector left or right to rewind or advance one frame Movie icon
at a time.
End playback
Press the selector up to end playback.
Adjust speed
Press the selector left or right to adjust playback speed during playback.
Press MENU/OK to pause playback and display volume controls. Press the selector up
Adjust volume
or down to adjust the volume; press MENU/OK again to resume playback. Volume
can also be adjusted using D SOUND SETTING > PLAYBACK VOLUME (P 116).
PLAY
±0
Progress is shown in the display during playback.
Progress bar
29m59s
Q Do not cover the speaker during playback.
STOP
PAUSE
Playback Speed
Press the selector left or right to adjust playback speed during playback. Speed is shown by the Arrow
number of arrows (M or N).
29m59s
STOP
46
PAUSE
The Q (Quick Menu) Button
Using the Q Button
Press Q for quick access to selected options.
The Quick Menu Display
At default settings, the quick menu contains the following items.
SELECT CUSTOM SETTING
BASE
SET
A SELECT CUSTOM SETTING
B AF MODE
C DYNAMIC RANGE
D WHITE BALANCE
E NOISE REDUCTION
F IMAGE SIZE
G IMAGE QUALITY
H FILM SIMULATION
I HIGHLIGHT TONE
J SHADOW TONE
K COLOR
L SHARPNESS
M SELF-TIMER
N FACE/EYE DETECTION SETTING
O FLASH FUNCTION SETTING
P EVF/LCD BRIGHTNESS
The Q (Quick Menu) Button
The quick menu shows the options currently selected for items B—P, which can be changed as
described on page 49. The H IMAGE QUALITY SETTING > SELECT CUSTOM SETTING item (item A)
shows the current custom settings bank:
• q: No custom settings bank selected.
• t — u: Select a bank to view the settings saved using the H IMAGE QUALITY SETTING > EDIT/
SAVE CUSTOM SETTING option (P 83).
• r — s: The current custom settings bank.
47
Using the Q Button
Viewing and Changing Settings
1 Press Q to display the quick menu during shooting.
SELECT CUSTOM SETTING
BASE
SET
2 Use the selector to highlight items and rotate the rear command dial
to change.
R Changes are not saved to the current settings bank (P 47). Settings that
differ from those in the current settings bank (t — u) are shown in
red.
3 Press Q to exit when settings are complete.
48
Using the Q Button
Editing the Quick Menu
To choose the items displayed in the quick menu:
1 Press and hold the Q button during shooting.
SELECT CUSTOM SETTING
SET
END
2 The current quick menu will be displayed; use the selector to highlight the item you wish to change
and press MENU/OK. You will be given the following choice of items to assign to the selected position:
SELECT CUSTOM SETTING *
DYNAMIC RANGE *
WHITE BALANCE *
NOISE REDUCTION *
IMAGE SIZE
IMAGE QUALITY
FILM SIMULATION *
•
•
•
•
•
•
•
GRAIN EFFECT *
HIGHLIGHT TONE *
SHADOW TONE *
COLOR *
SHARPNESS *
SELF-TIMER
FACE/EYE DETECTION SETTING
•
•
•
•
•
•
•
PHOTOMETRY
AF MODE
AF-C CUSTOM SETTINGS
FLASH FUNCTION SETTING
FLASH COMPENSATION
MF ASSIST
MOVIE MODE
•
•
•
•
•
MIC LEVEL ADJUSTMENT
EVF/LCD BRIGHTNESS
EVF/LCD COLOR
SHUTTER TYPE
NONE
* Stored in custom settings bank.
R Select NONE to assign no option to the selected position. When SELECT CUSTOM SETTING is selected,
current settings are shown in the quick menu by the label BASE.
The Q (Quick Menu) Button
•
•
•
•
•
•
•
3 Highlight the desired item and press MENU/OK to assign it to the selected position.
R The quick menu can also be edited using D BUTTON/DIAL SETTING > EDIT/SAVE QUICK MENU (P 119).
49
The Fn (Function) Buttons
Using the Function Buttons
The roles played by each of the function buttons can be selected by pressing and holding the button.
The default options are shown below:
Fn1 button
Fn2 button
Fn3 button
Recording movies (P 44)
Bright frame simulation (P 30)
Metering (P 60)
Fn4 button
Fn5 button
Fn6 button
Film simulation (P 61)
White balance (P 62)
AF mode (P 67)
Center of rear command dial
Focus check (P 65)
50
Using the Function Buttons
Assigning Roles to the Function Buttons
To assign roles to the function buttons, press and hold the DISP/BACK button until the menu below is
displayed. Select buttons to choose their roles.
FUNCTION (Fn) SETTING
SET
PREVIEW DEPTH OF FIELD
ISO AUTO SETTING
SELF-TIMER
AE BKT
IMAGE SIZE
IMAGE QUALITY
DYNAMIC RANGE
FILM SIMULATION
•
•
•
•
•
•
•
•
GRAIN EFFECT
WHITE BALANCE
PHOTOMETRY
AF MODE
AF-C CUSTOM SETTINGS
FOCUS AREA
FOCUS CHECK
FLASH FUNCTION SETTING
•
•
•
•
•
•
•
•
TTL-LOCK
MODELING FLASH
SELECT CUSTOM SETTING
MOVIE
FACE/EYE DETECTION SETTING
RAW
APERTURE SETTING
WIRELESS COMMUNICATION
•
•
•
•
•
•
SHUTTER TYPE
PREVIEW EXP./WB IN MANUAL MODE
PREVIEW PIC. EFFECT
BRIGHT FRAME SIMULATOR
BRIGHT FRAME BRIGHTNESS
NONE
R To disable the selected button, choose NONE.
R The roles played by the six function buttons can also be selected using D BUTTON/DIAL SETTING >
FUNCTION (Fn) SETTING (P 119).
The Fn (Function) Buttons
•
•
•
•
•
•
•
•
CANCEL
51
Using the Function Buttons
Viewing Function Button Options
You can also display options for any of the function buttons by pressing and holding the button (but note that
in focus mode M, pressing and holding function buttons will instead display MF assist options).
R The above does not apply to any button to which FOCUS CHECK is currently assigned.
■ TTL-LOCK
If TTL-LOCK is selected, you can press the control to lock flash output according to the option selected
for F FLASH SETTING > TTL-LOCK MODE (P 102).
■ MODELING FLASH
If MODELING FLASH is selected when a compatible shoe-mounted flash unit is attached, you can
press the control to test-fire the flash and check for shadows and the like (modeling flash).
52
More on Photography and Playback
Use the DRIVE (e) button to choose the drive mode.
1 Press the DRIVE (e) button to display drive
2 Press the selector up or down to highlight a
drive mode.
Icon
B
R
O
W
X
H
Y
j
Y
Drive mode
STILL IMAGE
CONTINUOUS
AE BKT
ISO BKT
FILM SIMULATION BKT
WHITE BALANCE BKT
DYNAMIC RANGE BKT
MULTIPLE EXPOSURE
ADVANCED FILTER
3 Press the selector left or right to choose a setting.
• Burst mode (CONTINUOUS): Choose the frameadvance rate.
• ISO/WB BKT: Choose the bracketing increment.
• ADVANCED FILTER: Choose a filter effect.
• Other modes: Proceed to Step 4.
mode options.
P
—
54
55
57
56
4 Press MENU/OK.
More on Photography and Playback
Drive Mode
5 Take pictures.
R In burst mode, pictures will be taken while the
shutter button is pressed. Shooting ends when
the button is released, the maximum number of
pictures has been taken, or the memory card is
full.
53
Drive Mode
R Burst Mode (CONTINUOUS)
Capture motion in a series of pictures.
R Frame rate varies with the subject, shutter speed, sensitivity, and focus mode and may slow as more shots are
taken.
R Depending on shooting conditions, the frame rate may drop or the flash may not fire.
R Additional time may be required to record pictures when shooting ends.
R If file numbering reaches 999 before shooting is complete, the remaining pictures will be recorded to a new
folder (P 122).
R Burst shooting may not begin if the space available on the memory card is insufficient.
Focus and Exposure
To vary focus and exposure with each shot, select focus mode C; in other modes, focus and exposure are determined by the first shot in each series.
Q Selecting 8.0 fps in focus mode C restricts the choice of focus frames (P 71).
Q Exposure and focus tracking performance may vary with aperture, sensitivity, and shooting conditions.
54
Drive Mode
Option
O AE BKT
W ISO BKT
X FILM SIMULATION BKT
H WHITE BALANCE BKT
Y DYNAMIC RANGE BKT
Description
Use A SHOOTING SETTING > AE BKT to choose the bracketing amount and number of shots
(P 98). Each time the shutter button is pressed, the camera will take the specified number of shots:
one using the metered value for exposure and the others over- or under-exposed by multiples of the
selected bracketing amount (P 58).
R Regardless of the bracketing amount, exposure will not exceed the limits of the exposure metering
system.
Select a bracketing amount. Each time the shutter is released, the camera will take a picture at the
current sensitivity (P 59) and process it to create two additional copies, one with sensitivity raised
and the other with sensitivity lowered by the selected amount (regardless of the amount selected,
sensitivity will not exceed ISO 12800 or fall below ISO 200).
Each time the shutter is released, the camera takes one shot and processes it to create copies at the
settings chosen using A SHOOTING SETTING > FILM SIMULATION BKT (P 61, 98).
Select a bracketing amount. Each time the shutter button is pressed, the camera takes three shots:
one at the current white balanced setting (P 62), one with fine-tuning increased by the selected
amount, and another with fine-tuning decreased by the selected amount.
Each time the shutter button is pressed, the camera takes three shots with different dynamic ranges
(P 90): 100% for the first, 200% for the second, and 400% for the third. While dynamic range bracketing is in effect, sensitivity will be restricted to a minimum of ISO 800 (or to a minimum of ISO 200
to 800 when an auto option is selected for sensitivity); the sensitivity previously in effect is restored
when bracketing ends.
More on Photography and Playback
Bracketing
Automatically vary settings over a series of pictures.
55
Drive Mode
Y Advanced Filters
Take photos with filter effects.
Filter
G TOY CAMERA
H MINIATURE
I POP COLOR
J HIGH-KEY
Z LOW-KEY
K DYNAMIC TONE
X SOFT FOCUS
u PARTIAL COLOR (RED)
v PARTIAL COLOR (ORANGE)
w PARTIAL COLOR (YELLOW)
x PARTIAL COLOR (GREEN)
y PARTIAL COLOR (BLUE)
z PARTIAL COLOR (PURPLE)
Description
Choose for a retro toy camera effect.
The tops and bottoms of pictures are blurred for a diorama effect.
Create high-contrast images with saturated colors.
Create bright, low-contrast images.
Create uniformly dark tones with few areas of emphasized highlights.
Dynamic tone expression is used for a fantasy effect.
Create a look that is evenly soft throughout the whole image.
Areas of the image that are the selected color are recorded in that color. All other areas of the
image are recorded in black-and-white.
R Depending on the subject and camera settings, images may in some cases be grainy or vary in brightness and
hue.
56
Drive Mode
+
1 Select j for drive mode (P 53).
4 Take the second shot, using the first frame as a
guide.
2 Take the first shot.
More on Photography and Playback
j Multiple Exposures
Create a photograph that combines two exposures.
EXIT
3 Press MENU/OK. The first shot will be shown superimposed on the view through the lens and
you will be prompted to take the second shot.
NEXT
RETRY
30
2.0
5 Press MENU/OK to create the multiple exposure,
or press the selector left to return to Step 4
and retake the second shot.
EXIT
R To return to Step 2 and retake the first shot,
press the selector left. To save the first shot and
exit without creating a multiple exposure, press
DISP/BACK.
RETRY
EXIT
57
Exposure Compensation
Rotate the exposure compensation dial to adjust
exposure when photographing very bright, very
dark, or high-contrast subjects. The effect is visible in the display.
■ C (Custom)
When the exposure compensation dial is rotated
to C, exposure compensation can be adjusted by
rotating the front command dial.
set
Exposure compensation
indicator
Choose positive values (+) to
increase exposure
R The front command dial can be used to set exposure
compensation to values between −5 and +5 EV.
R In exposure modes other than A (aperture-priority
AE), the front command dial can be used to set shutter speed or exposure compensation. Press the dial
to toggle between the two.
Choosing an Exposure Compensation Value
• Backlit subjects: Choose values from
+2/3 EV to +12/3 EV.
Choose negative values (–) to
reduce exposure
Q The amount of compensation available varies with
the shooting mode.
58
• Highly reflective subjects or very bright
scenes (e.g., snowfields): +1 EV
• Scenes that are mostly sky: +1 EV
• Spotlit subjects (particularly if photographed against dark backgrounds): –2/3 EV
• Subjects with low reflectivity (pine trees or dark-colored foliage):
–2/3 EV
Sensitivity
Option
A (auto)
12800–200
H (51200/25600)/
L (100/125/160)
Description
Sensitivity is automatically adjusted in response to shooting conditions according to option chosen
for A SHOOTING SETTING > ISO AUTO SETTING. Choose from AUTO1, AUTO2, and AUTO3 (P 100).
Adjust sensitivity manually. Selected value is shown in display.
Choose for special situations. Note that mottling may appear in pictures taken at H, while L reduces
dynamic range (P 119).
More on Photography and Playback
“Sensitivity” (the camera’s sensitivity to light) can be adjusted by lifting and rotating the ISO dial. Higher
values can be used to reduce blur when lighting is poor (note, however, that mottling may appear in
pictures taken at high sensitivities).
R Sensitivity is not reset when the camera is turned off.
R Use D BUTTON/DIAL SETTING > ISO DIAL SETTING (H) to choose the sensitivity assigned to the H position.
R Use D BUTTON/DIAL SETTING > ISO DIAL SETTING (L) to choose the sensitivity assigned to the L position.
59
Metering
Choose how the camera meters exposure. Press the function (Fn3)
button to display the options shown below, then use the selector to
highlight an option and press MENU/OK to select.
Q The selected option will only take effect when G AF/MF SETTING >
FACE/EYE DETECTION SETTING is off (P 95).
Mode
Description
The camera instantly determines exposure based on an analysis of composition, color, and brightness
o
distribution. Recommended in most situations.
(MULTI)
p
The camera meters the entire frame but assigns the greatest weight to the area at the center.
(CENTER WEIGHTED)
The camera meters lighting conditions in an area at the center of the frame equivalent to 2% of the total.
v
Recommended with backlit subjects and in other cases in which the background is much brighter or
(SPOT)
darker than the main subject.
Exposure is set to the average for the entire frame. Provides consistent exposure across multiple shots
w
with the same lighting, and is particularly effective for landscapes and portraits of subjects dressed in
(AVERAGE)
black or white.
R Metering options can also be accessed using A SHOOTING SETTING > PHOTOMETRY (P 98).
60
Film Simulation
Option
Description
c (PROVIA/STANDARD) Standard color reproduction. Suited to a wide range of subjects, from portraits to landscapes.
A high-contrast palette of saturated colors, suited to nature photos.
> (Velvia/VIVID)
Enhances the range of hues available for skin tones in portraits while preserving the bright blues of daye (ASTIA/SOFT)
light skies. Recommended for outdoor portrait photography.
i (CLASSIC CHROME) Soft color and enhanced shadow contrast for a calm look.
g (PRO Neg. Hi)
Offers slightly more contrast than h (PRO Neg. Std). Recommended for outdoor portrait photography.
A soft-toned palette. The range of hues available for skin tones is enhanced, making this a good choice for
h (PRO Neg. Std)
studio portrait photography.
Take black-and-white photos with rich gradation and outstanding sharpness. Available with yellow (Ye),
a (ACROS) *
red (R), and green (G) filters.
b (MONOCHROME) * Take pictures in standard black and white. Available with yellow (Ye), red (R), and green (G) filters.
Take pictures in sepia.
f (SEPIA)
More on Photography and Playback
Simulate the effects of different kinds of film, including black-andwhite (with or without color filters). Press the function (Fn4) button to
display the options shown below, then use the selector to highlight
an option and press MENU/OK to select.
* Filters deepen shades of gray corresponding to hues complementary to the selected color. The yellow (Ye) filter deepens purples and
blues and the red (R) filter blues and greens. The green (G) filter deepens reds and browns, including skin tones, making it a good
choice for portraits.
R Film simulation options can be combined with tone and sharpness settings (P 91).
R Film simulation options can also be accessed using H IMAGE QUALITY SETTING > FILM SIMULATION (P 90).
61
White Balance
For natural colors, choose a white balance option that matches the
light source. Press the function (Fn5) button to display the options
shown below, then press the selector up or down to highlight an option and press MENU/OK to select.
Option
Description
Option
Description
AUTO White balance adjusted automatically.
i For subjects in direct sunlight.
k
j For subjects in the shade.
l Measure a value for white balance (P 63).
k Use under “daylight” fluorescent lights.
m
l Use under “warm white” fluorescent lights.
Selecting this option displays a list of color
m Use under “cool white” fluorescent lights.
temperatures (P 63); highlight a temperan Use under incandescent lighting.
k ture and press MENU/OK to select the highlighted option and display the fine-tuning g Reduces the blue cast typically associated
with underwater lighting.
dialog.
WB SHIFT
AUTO
R:0 B:0
SET
R White balance is adjusted for flash lighting only in AUTO and g modes. Turn the flash off using other white
balance options (P 79).
R Results vary with shooting conditions. Play pictures back after shooting to check colors.
R White balance options can also be accessed using H IMAGE QUALITY SETTING > WHITE BALANCE (P 90).
62
White Balance
k: Color Temperature
Color temperature is an objective measure of the color of a light source, expressed in Kelvin (K). Light sources
with a color temperature close to that of direct sunlight appear white; light sources with a lower color temperature have a yellow or red cast, while those with a higher color temperature are tinged with blue. You can match
color temperature to the light source as shown in the following table, or choose options that differ sharply from
the color of the light source to make pictures “warmer” or “colder.”
Choose for redder light sources
or “colder” pictures
2,000 K
Candlelight
Sunset/sunrise
More on Photography and Playback
h: Custom White Balance
Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will
be displayed; frame a white object so that it fills the display and press the shutter button all the way down to
measure white balance (to select the most recent custom value and exit without measuring white balance,
press DISP/BACK, or press MENU/OK to select the most recent value and display the fine-tuning dialog).
• If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value.
• If “UNDER” is displayed, raise exposure compensation (P 58) and try again.
• If “OVER” is displayed, lower exposure compensation (P 58) and try again.
Choose for bluer light sources
or “warmer” pictures
5,000 K
Direct sunlight
15,000 K
Blue sky
Shade
63
Focus Mode
Use the focus mode selector to choose how the camera focuses (note
that regardless of the option selected, manual focus will be used
when the lens is in manual focus mode).
• S (single AF): Focus locks while the shutter button is pressed halfway.
Choose for stationary subjects.
• C (continuous AF): Focus is continually adjusted to reflect changes in the
distance to the subject while the shutter button is pressed halfway. Use for subjects that are in motion. Eye-detection AF is not available.
• M (manual): Focus manually using the lens focus ring. Rotate the ring left to reduce the focus distance,
right to increase. The manual focus indicator indicates how closely the focus distance matches the
distance to the subject in the focus brackets (the white line indicates the focus distance, the blue
bar the depth of field, or in other words the distance in front of and behind the focus point that appears to be in focus); you can also check focus visually in the viewfinder or LCD monitor. Choose for
manual control of focus or in situations in which the camera is unable to focus using autofocus (P 78).
Reduce focus
distance
55
35
23 18
Increase focus
distance
㹋
A
XF
ZOOM
18-55
Focus distance
(white line)
Manual focus
mode icon
Manual focus
indicator
Depth of field
(blue bar)
R Use D BUTTON/DIAL SETTING > FOCUS RING (P 120) to reverse the direction of rotation of the focus ring.
R To use autofocus to focus on the subject in the selected focus area (P 68), press the AF-L button (the size of
the focus area can be chosen with the rear command dial). In manual focus mode, you can use this feature
to quickly focus on a chosen subject using either single or continuous AF according to the option chosen for
G AF/MF SETTING > INSTANT AF SETTING (P 96).
64
Focus Mode
■ The Focus Indicator
The focus indicator turns green when the subject is in focus and blinks white when
the camera is unable to focus. Brackets (“( )”) indicate that the camera is focusing
and are displayed continuously in mode C. j is displayed in manual focus mode.
Focus indicator
Checking Focus
To zoom in on the current focus area (P 68) for precise focus, press
the center of the rear command dial. Press the center of the rear
command dial again to cancel zoom. In manual focus mode, zoom
can be adjusted by rotating the rear command dial when STANM
DARD or FOCUS PEAK HIGHLIGHT is selected for G AF/MF SET- M
TING > MF ASSIST (P 96), while if ON is selected for G AF/MF SETTING > FOCUS CHECK (P 96), the camera will automatically zoom in on the selected focus area when the focus
ring is rotated. Focus zoom is not available in focus mode C or when G AF/MF SETTING > PRE-AF (P 95) is on
or an option other than r SINGLE POINT is selected for AF MODE (P 67).
More on Photography and Playback
R The camera can show focus distance in meters or feet. Use D SCREEN SETTING > FOCUS SCALE UNITS (P 118)
to choose the units used.
R If ON is selected for G AF/MF SETTING > PRE-AF (P 95), focus will be adjusted continuously in modes S and C
even when the shutter button is not pressed.
R Focus area selection using the focus stick is available during focus zoom.
R Use D BUTTON/DIAL SETTING > FUNCTION (Fn) SETTING to change the function performed by the center
of the command dial or assign its default function to other controls (P 51).
65
Focus Mode
■ MF Assist
The G AF/MF SETTING > MF ASSIST (P 96) option can be used to check focus when pictures are
framed in the LCD monitor or electronic viewfinder in manual focus mode.
R The MF ASSIST menu can be displayed by pressing and holding the center of the rear command dial.
The following options are available:
• FOCUS PEAK HIGHLIGHT: Highlights high-contrast outlines. Rotate the focus ring until
the subject is highlighted.
• DIGITAL SPLIT IMAGE: Displays a split image in the center of the frame. Frame the
subject in the split-image area and rotate the focus ring until the three parts of the
split image are correctly aligned.
66
Focus Mode
More on Photography and Playback
Autofocus Options (AF Mode)
To choose the AF mode for focus modes S and C, press the function
button (Fn6) to display the options shown below, then press the selector up or down to highlight an option and press MENU/OK to select.
• r SINGLE POINT: The camera focuses on the subject in the selected focus point (P 69). The number of focus points available can be
selected using G AF/MF SETTING > NUMBER OF FOCUS POINTS
(P 94). Use for pin-point focus on a selected subject.
• y ZONE: The camera focuses on the subject in the selected focus zone (P 70). Focus zones include
multiple focus points (7 × 7, 5 × 5, or 3 × 3), making it easier to focus on subjects that are in motion.
• z WIDE/TRACKING: In focus mode C, the camera tracks focus on the subject in the selected focus
point while the shutter-release button is pressed halfway (P 71). In focus mode S, the camera automatically focuses on high-contrast subjects; the areas in focus are shown in the display. The camera
may be unable to focus on small objects or subjects that are moving rapidly.
R AF mode options can also be accessed using G AF/MF SETTING > AF MODE (P 93).
67
Focus Mode
Focus-Point Selection
Use the focus stick (focus lever) to choose a focus point for autofocus. The procedure for selecting the
focus point varies with the option chosen for AF mode (P 67).
R Focus-area selection can also be used to choose the focus point for manual focus and focus zoom.
Tilt the focus stick to position the focus frame, or press the center of the stick to return to the center
focus point.
Focus frame
Available Focus Points
Fewer focus points are available for intelligent hybrid AF, which combines phase-detection with TTL contrastdetect AF.
TTL contrast-detect
68
Intelligent hybrid AF
(TTL contrast-detect AF + phase-detection AF)
Focus Mode
R Focus-area selection can also be accessed using G AF/MF SETTING > FOCUS AREA (P 93).
■ Single Point AF
Press the center of the focus stick to display the focus points (“”) and
focus frame. Use the stick to position the focus frame over the desired
focus point, or press the center of the stick to return to the center point.
Focus point
Focus frame
To choose the size of the focus frame, rotate the rear command dial.
Rotate the dial left to reduce the frame by up to 50%, right to enlarge it
by up to 150%, or press the center of the dial to restore the frame to its
original size. Press MENU/OK to put your selection into effect.
More on Photography and Playback
The Focus Point Display
The focus stick (focus lever) can be used to display available focus points.
69
Focus Mode
■ Zone AF
Press the center of the focus stick to display the focus zone. Use the
stick to position the zone or press the center of the stick to return the
zone to the center of the display.
To choose the number of focus frames in the zone, rotate the rear command dial. Rotate the dial right to cycle through zone sizes in the order 3 × 3, 5 × 5, 7 × 7, 3 × 3…, left to cycle through zone sizes in reverse
order, or press the center of the dial to select a zone size of 3 × 3. Press
MENU/OK to put your selection into effect.
70
Focus zone
Focus Mode
Focus frame
Q Manual focus-frame selection is not available when wide/tracking is selected in focus mode S.
Burst Mode Focus-Frame Selection
When continuous high-speed (8.0 fps) is selected for drive mode, the number of focus frames available in focus
mode C drops.
Single point
Zone
More on Photography and Playback
■ Tracking (Focus Mode C Only)
Press the center of the focus stick to display the focus frame. Use the
stick to position the focus frame, or press the center of the stick to return the frame to the center of the display. Press MENU/OK to put your
selection into effect. The camera will track focus on the subject while
the shutter button is pressed halfway.
Wide/Tracking
71
Long Time-Exposures (T/B)
Select a shutter speed of T (time) or B (bulb) for long time-exposures.
R Use of a tripod is recommended to prevent the camera from moving during the exposure.
R To reduce “noise” (mottling) in long time-exposures, select ON for H IMAGE QUALITY SETTING > LONG EXPOSURE NR (P 91). Note that this may increase the time needed to record images after shooting.
Time (T)
1 Rotate the shutter speed dial to T.
2 Rotate the front command dial to
choose a shutter speed.
S
2”
3 Press the shutter button all the way
down to take a picture at the selected shutter speed. A count-down
timer will be displayed while the exposure is in progress.
72
Bulb (B)
1 Rotate the shutter speed dial to B.
2 Press the shutter button all the way
down. The shutter will remain open
for up to 60 minutes while the shutter button is pressed; the display
shows the time elapsed since the
exposure started.
R Selecting an aperture of A fixes shutter speed at 30 s.
Long Time-Exposures (T/B)
Third-Party Remote Releases
Electronic releases from thirdparty suppliers can be connected via the microphone/remote
release connector. A confirmation dialog will be displayed
when a third-party release is
connected; press MENU/OK and
select n REMOTE for MIC/
REMOTE RELEASE.
CHECK MIC/REMOTE RELEASE
SETTING
SKIP
SET
More on Photography and Playback
Using a Remote Release
An optional RR-90 remote release can be used for
long time-exposures. See the manual provided
with the RR-90 for more information.
73
The Self-Timer
Use the timer for self-portraits or to prevent blur caused by camera shake.
1 Press MENU/OK in shooting mode to display the
shooting menu.
4 Press the shutter button halfway to focus.
Q Stand behind the camera when using the shutter button. Standing in front of the lens can interfere with focus and exposure.
5 Press the shutter button
2 Select the A SHOOTING SETTING tab (P 88),
then highlight SELF-TIMER and press MENU/OK.
3 Press the selector up or down to highlight the
desired option and press MENU/OK to select.
Option
Description
The shutter is released two seconds after the
shutter button is pressed. Use to reduce blur
R 2 SEC
caused by the camera moving when the shutter button is pressed.
The shutter is released ten seconds after the
S 10 SEC shutter button is pressed. Use for photographs
in which you wish to appear yourself.
OFF
Self-timer off.
9
the rest of the way down to
start the timer. The display
in the monitor shows the
number of seconds remaining until the shutter is released. To stop
the timer before the picture is taken, press
DISP/BACK.
The self-timer lamp on
the front of the camera
will blink immediately
before the picture is
taken. If the two-second timer is selected,
the self-timer lamp will blink as the timer
counts down.
R The self-timer turns off automatically when the
camera is turned off.
74
Interval Timer Photography
1 Press MENU/OK in shooting mode to display the shooting menu.
Select the A SHOOTING SETTING tab (P 88), then highlight
INTERVAL TIMER SHOOTING and press MENU/OK.
2 Use the selector to choose the interval and number of shots. Press MENU/OK to
INTERVAL/NUMBER OF TIMES
INTERVAL
NUMBER OF TIMES
proceed.
END
3 Use the selector to choose the starting time and then press MENU/OK. Shooting
CANCEL
START WAITING TIME
will start automatically.
More on Photography and Playback
Follow the steps below to configure the camera to take photos automatically at a preset interval.
LATER
ESTIMATED START TIME 11 : 00 PM
START
CANCEL
Q Interval timer photography can not be used at a shutter speed of B (bulb) or with multiple exposure photography. In burst mode, only one picture will be taken each time the shutter is released.
R Use of a tripod is recommended.
R Check the battery level before starting. We recommend using an optional AC-9V AC power adapter and
CP-W126 DC coupler.
R The display turns off between shots and lights a few seconds before the next shot is taken. The display can be
activated at any time by pressing the shutter button.
75
Focusing and Taking Pictures
Press the shutter button halfway to focus and the rest of the way down to shoot.
1 Focus.
Frame the picture with your subject in the center of the display and press the shutter
button halfway to focus.
R If the subject is poorly lit, the AF-assist illuminator may light (P 95).
If the camera is able to focus, it will beep twice and the focus indicator and frame in
focus will glow green. Focus and exposure will lock while the shutter button is
pressed halfway.
Focus frame
Focus indicator
If the camera is unable to focus, the focus frame will turn red, s will be displayed, and the focus indicator will blink white.
2 Shoot.
Smoothly press the shutter button the rest of the way down to take the picture.
76
Focus/Exposure Lock
1 Focus: Position the subject in the focus frame and press the shutter button halfway to lock focus and exposure. Focus and exposure will remain locked while
the shutter button is pressed halfway (AF/AE lock).
P
R Focus and exposure can also be locked with the AF-L and AE-L buttons, respectively (if AE/AF LOCK is
selected for D BUTTON/DIAL SETTING > AF-LOCK MODE, pressing the AF-L button will lock both focus
and exposure; P 120).
2 Recompose: Keep the shutter button pressed halfway or keep the AF-L or AE-L button pressed.
R Focus and/or exposure will remain locked while the AF-L or AE-L button is pressed,
whether or not the shutter button is pressed halfway. If AE&AF ON/OFF SWITCH
is selected for D BUTTON/DIAL SETTING > AE/AF-LOCK MODE (P 120), focus and/
or exposure lock when the button is pressed and remain locked until the button is
pressed again.
More on Photography and Playback
To compose photographs with off-center subjects:
P
3 Shoot: Press the button all the way down.
R The roles of the AE-L and AF-L buttons can be reversed using D BUTTON/DIAL SETTING > AE-L/AF-L BUTTON
SETTING (P 120).
77
Focus/Exposure Lock
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed
below.
• Very shiny subjects such as mirrors or car bodies.
• Fast-moving subjects.
•
•
•
•
Subjects photographed through a window or other reflective object.
Dark subjects and subjects that absorb rather than reflect light, such as hair or fur.
Insubstantial subjects, such as smoke or flame.
Subjects that show little contrast with the background (for example, subjects in clothing that is the same color
as the background).
• Subjects positioned in front of or behind a high-contrast object that is also in the focus frame (for example, a
subject photographed against a backdrop of highly contrasting elements).
78
Flash Photography
1 Remove the hot shoe cover and slide the flash
onto the hot shoe.
3 Select FLASH FUNCTION
SETTING in the F FLASH
SETTING menu.
FLASH SETTING
FLASH FUNCTION SETTING
RED EYE REMOVAL
TTL-LOCK MODE
LED LIGHT SETTING
MASTER SETTING
CH SETTING
EXIT
Q If the flash is not raised, settings will be adjusted
for units connected via the sync terminal (P 144).
4 Highlight items using the
2 Turn the flash on.
MODE
SUPPLIED FLASH
selector and rotate the rear
command dial to change
the highlighted setting.
ADJUST
More on Photography and Playback
Use an optional flash unit for additional lighting when shooting at night or indoors under low light.
END
5 Press DISP/BACK to put the changes into effect.
R For more information, see the documentation
provided with the flash unit.
R The options available vary with the flash unit.
See“Using Shoe-Mounted Flash Units”(P 143) for
more information.
Q Depending on the distance to the subject, some
lenses may cast shadows in photos taken with the
flash.
Q The flash will not fire at some settings, for example
when the electronic shutter is used.
Q Choose shutter speeds slower than 250X when using the flash in exposure mode S (shutter-priority
AE) or manual (M).
R In TTL mode, the flash may fire several times with
each shot. Do not move the camera until shooting
is complete.
79
Flash Photography
Red-Eye Removal
Red-eye removal is available when an option other
than OFF is selected for F FLASH SETTING > RED
EYE REMOVAL and G AF/MF SETTING > FACE/EYE
DETECTION SETTING is ON. Red-eye removal minimizes “red-eye” caused when light from the flash is
reflected from the subject’s retinas.
Flash Sync Speed
The flash will synchronize with the shutter at shutter
speeds of 1/250 s or slower.
Optional Flash Units
The camera can be used with optional FUJIFILM
shoe-mounted flash units (P 140).
Optional Flash Units
Do not use third-party flash units that apply over
300 V to the camera hot shoe.
80
The Sync Terminal
Use the sync terminal to connect flash units that require a sync cable.
Recording Pictures in RAW Format
1 Press MENU/OK in shooting mode to display the shooting menu. Select the H IMAGE QUALITY
SETTING tab (P 88), then highlight IMAGE QUALITY (P 89) and press MENU/OK.
2 Highlight an option and press MENU/OK. Select RAW to record only RAW images, or FINE+RAW or
NORMAL+RAW to record both JPEG copy together with the RAW images. FINE+RAW uses lower
JPEG compression ratios for higher-quality JPEG images, while NORMAL+RAW uses higher JPEG
compression ratios to increase the number of images that can be stored.
The Function Buttons
To toggle RAW image quality on or off for a single shot, assign RAW to a function button (P 51). If a JPEG option
is currently selected for image quality, pressing the button temporarily selects the equivalent JPEG+RAW option.
If a JPEG+RAW option is currently selected, pressing the button temporarily selects the equivalent JPEG option,
while if RAW is selected, pressing the button temporarily selects FINE. Taking a picture or pressing the button
again restores the previous setting.
More on Photography and Playback
To record raw, unprocessed data from the camera image sensor, select a RAW option for image quality in the shooting menu as described below. JPEG copies of RAW images can be created using
C PLAY BACK MENU > RAW CONVERSION, or RAW images can be viewed on a computer using the
RAW FILE CONVERTER EX 2.0 application (P 82, 130).
81
Recording Pictures in RAW Format
Creating JPEG Copies of RAW Pictures
RAW pictures store information on camera settings separately from the data captured by the camera
image sensor. Using C PLAY BACK MENU > RAW CONVERSION (P 107), you can create JPEG copies
of RAW pictures using different options for the settings listed below. The original image data are unaffected, allowing a single RAW image to be processed in a multitude of different ways.
1 Press MENU/OK during playback to display
the playback menu, then press the selector up or down to highlight C PLAY BACK
MENU > RAW CONVERSION (P 106) and
press MENU/OK to display the settings listed
in the table at right.
R These options can also be displayed by pressing
Q button during playback.
2 Press the selector up or
RAW CONVERSION
REFLECT SHOOTING COND.
PUSH/PULL PROCESSING
DYNAMIC RANGE
FILM SIMULATION
GRAIN EFFECT
WHITE BALANCE
down to highlight a setting
and press the selector right
to select. Press the selector up or down to highlight
the desired option and press MENU/OK to select
and return to the settings list. Repeat this step
to adjust additional settings.
CREATE
CANCEL
3 Press the Q button to preview the JPEG copy
and press MENU/OK to save.
82
Setting
REFLECT SHOOTING
COND.
PUSH/PULL
PROCESSING
Description
Create a JPEG copy using the settings in effect at the time the photo was taken.
Adjust exposure by –1 EV to +3 EV in increments of 1/3 EV.
Enhance details in highlights for natural
DYNAMIC RANGE
contrast (P 90).
Simulate the effects of different types of film
FILM SIMULATION
(P 61).
GRAIN EFFECT
Add a film grain effect (P 90).
WHITE BALANCE Adjust white balance (P 62).
WB SHIFT
Fine-tune white balance (P 62).
HIGHLIGHT TONE Adjust highlights (P 91).
SHADOW TONE
Adjust shadows (P 91).
COLOR
Adjust color density (P 91).
SHARPNESS
Sharpen or soften outlines (P 91).
NOISE REDUCTION Process the copy to reduce mottling (P 91).
Improve definition by adjusting for diffracLENS MODULATION
tion and the slight loss of focus at the peOPTIMIZER
riphery of the lens (P 91).
Choose the color space used for color reproCOLOR SPACE
duction (P 91).
Saving Settings
1 Press MENU/OK in shooting mode to display the shooting menu. Select the H IMAGE
QUALITY SETTING tab (P 88), then highlight EDIT/SAVE CUSTOM SETTING (P 92)
and press MENU/OK.
2 Highlight a custom settings bank and press MENU/OK to select. Adjust the following as desired and press DISP/BACK when adjustments are complete: DYNAMIC
RANGE, FILM SIMULATION, GRAIN EFFECT, WHITE BALANCE, HIGHLIGHT
TONE, SHADOW TONE, COLOR, SHARPNESS, and NOISE REDUCTION.
3 A confirmation dialog will be displayed; highlight OK and press MENU/OK.
IMAGE QUALITY SETTING
3/3
CUSTOM 1
SELECT CUSTOM SETTING
EDIT/SAVE CUSTOMCUSTOM
SETTING2
CUSTOM 3
CUSTOM 4
CUSTOM 5
CUSTOM 6
CUSTOM 7
CUSTOM 1
1/2
XXXXX
SAVE
CURRENT SETTINGS
DYNAMIC RANGE
FILM SIMULATION
GRAIN EFFECT
WHITE BALANCE
HIGHLIGHT TONE
SHADOW TONE
COLOR
AUTO
OFF
AUTO
0
0
0
BACK EXIT
SAVE CUSTOM SETTING
CUSTOM 1 SET OK?
More on Photography and Playback
Save up to 7 sets of custom camera settings for commonly-encountered situations. Saved settings can
be recalled using H IMAGE QUALITY SETTING > SELECT CUSTOM SETTING (P 92).
OK
CANCEL
R To replace the settings in the selected bank with the settings currently selected with the camera, select SAVE
CURRENT SETTINGS and press MENU/OK.
R To store current camera settings in the selected bank, highlight SAVE CURRENT SETTINGS in Step 2 and press
MENU/OK. Banks can be renamed using EDIT CUSTOM NAME.
R To restore default settings for the current bank, select RESET.
83
Using a Mount Adapter
When M-mount lenses are attached using an
optional FUJIFILM M MOUNT ADAPTER, the camera
processes pictures as they are taken to maintain
image quality and correct for a variety of effects.
Pressing the function button on the mount adapter displays l MOUNT ADAPTOR SETTING options.
R Mount adapter settings can also be accessing using A SHOOTING SETTING > MOUNT ADAPTER
SETTING (P 100).
R Before checking focus, set the focus mode selector
to M (P 64).
Bright Frame Brightness
Adjust the brightness of the bright frame in
the OVF display. Use the BRIGHT FRAME
BRIGHTNESS option to adjust the brightness
of the bright frame in the OVF display.
Lens Registration
■ Choosing a Focal Length
If the lens has a focal length
of 21, 24, 28, or 35 mm,
choose a matching option in
the l MOUNT ADAPTOR
SETTING menu.
For other lenses, select option
5 or 6 and use the selector to
enter the focal length.
■ Distortion Correction
Choose from STRONG, MEDIUM,
or WEAK options to correct
BARREL or PINCUSHION distortion.
Barrel distortion
LENS REGISTRATION
LENS 1
LENS 2
LENS 3
LENS 4
LENS 5
LENS 6
SET
LENS 5
INPUT FOCAL LENGTH
SET
CANCEL
LENS5 DISTORTION CORRECTION
BARREL STRONG
BARREL MEDIUM
BARREL WEAK
OFF
PINCUSHION WEAK
PINCUSHION MEDIUM
PINCUSHION STRONG
Pincushion distortion
R To determine the amount required, adjust distortion correction while taking photos of graph paper
or other objects featuring repeating vertical and
horizontal lines, such as the windows in a high-rise.
84
Using a Mount Adapter
NEXT
SET
To use color shading correction, follow the steps
below.
1 Rotate the rear command dial to choose a
corner. The selected corner is indicated by a
triangle.
2 Use the selector to adjust shading until there
is no visible difference in color between the
selected corner and the center of the image.
Press the selector left or right to adjust colors
on the cyan–red axis, up or down to adjust
colors on the blue–yellow axis.
■ Peripheral Illumination Correction
Choose from values between
–5 and +5. Choosing positive
values increases peripheral illumination, while choosing
negative values reduces peripheral illumination. Positive values are recommended for vintage lenses, negative values to
create the effect of images taken with an antique
lens or a pinhole camera.
SET
CANCEL
R To determine the amount required, adjust peripheral illumination correction while taking photos of
blue sky or a sheet of gray paper.
More on Photography and Playback
■ Color Shading Correction
Color (shading) variations between the center and edges
of the frame can be adjusted
separately for each corner.
R To determine the amount required, adjust color
shading correction while taking photos of blue sky
or a sheet of gray paper.
85
PhotoBook Assist
Create books from your favorite photos.
Creating a PhotoBook
1 Select NEW BOOK for C PLAY BACK
MENU > PHOTOBOOK ASSIST (P 106).
2 Scroll through the images and press the selector up to select or deselect. To display the
current image on the cover, press the selector
down. Press MENU/OK to exit when the book is
complete.
R Neither photographs a or smaller nor movies
can be selected for photobooks.
R The first picture selected becomes the cover image. Press the selector down to select a different
image for the cover.
86
3 Highlight COMPLETE PHOTOBOOK and
press MENU/OK (to select all photos or all photos matching the specified search conditions
for the book, choose SELECT ALL). The new
book will be added to the list in the photobook assist menu.
Q Books can contain up to 300 pictures.
Q Books that contain no photos are automatically deleted.
PhotoBook Assist
Editing and Deleting Photobooks
Display the photobook and press MENU/OK. The
following options will be displayed; select the
desired option and follow the on-screen instructions.
• EDIT: Edit the book as described in “Creating a
PhotoBook” (P 86).
• ERASE: Delete the book.
More on Photography and Playback
Viewing Photobooks
Highlight a book in the photobook assist menu
and press MENU/OK to display the book, then press
the selector left or right to scroll through the pictures.
Photobooks
Photobooks can be copied to a computer using MyFinePix Studio software (P 130).
87
Menus
Using the Menus: Shooting Mode
The shooting menu is used to adjust settings for a wide range of shooting conditions. Frequently-used
options can be saved to a personalized custom menu (“my menu”).
Using the Shooting Menu
1 Press MENU/OK in shooting mode to display the
menus.
4 Press the selector right to place the
cursor in the menu.
IMAGE QUALITY SETTING
IMAGE SIZE
IMAGE QUALITY
RAW RECORDING
FILM SIMULATION
GRAIN EFFECT
DYNAMIC RANGE
WHITE BALANCE
HIGHLIGHT TONE
5 Press the selector up or down to
highlight the desired item.
EXIT
6 Press the selector right to view op2 Press the selector left to highlight
the tab for the current menu.
IMAGE QUALITY SETTING
IMAGE SIZE
IMAGE QUALITY
RAW RECORDING
FILM SIMULATION
GRAIN EFFECT
DYNAMIC RANGE
WHITE BALANCE
HIGHLIGHT TONE
7 Press the selector up or down to
highlight the desired option.
EXIT
Tab
3 Press the selector down to highlight
the tab (H, G, A, F, B, or E) containing the desired item.
88
tions for the highlighted item.
8 Press MENU/OK to select the highlighted option.
9 Press DISP/BACK to return to the
shooting display.
R Use the front command dial to scroll through the
menus a page at a time.
Using the Menus: Shooting Mode
H IMAGE QUALITY SETTING
To adjust shooting settings that affect image quality, press MENU/OK in the
shooting display and select the H (IMAGE QUALITY SETTING) tab (P 88).
IMAGE QUALITY SETTING
IMAGE SIZE
IMAGE QUALITY
RAW RECORDING
FILM SIMULATION
GRAIN EFFECT
DYNAMIC RANGE
WHITE BALANCE
HIGHLIGHT TONE
EXIT
IMAGE SIZE
Choose the size and aspect ratio at which still pictures are recorded.
Image size
6000 × 4000
6000 × 3376
4000 × 4000
4240 × 2832
4240 × 2384
2832 × 2832
Option
Q3:2
Q 16 : 9
Q1:1
Image size
3008 × 2000
3008 × 1688
2000 × 2000
Menus
Option
O3:2
O 16 : 9
O1:1
P3:2
P 16 : 9
IMAGE SIZE is not reset when the camera is turned off or another P 1 : 1
shooting mode is selected.
Aspect Ratio
Pictures with an aspect ratio of 3 : 2 have the same proportions as
a frame of 35 mm film, while an aspect ratio of 16 : 9 is suited to
display on High Definition (HD) devices. Pictures with an aspect
ratio of 1 : 1 are square.
IMAGE QUALITY
Choose a file format and compression ratio. Select FINE or NORMAL to record JPEG images, RAW to record RAW images, or
FINE+RAW or NORMAL+RAW to record both JPEG and RAW images. FINE and FINE+RAW use lower JPEG compression ratios
for higher-quality JPEG images, while NORMAL and NORMAL+RAW use higher JPEG compression ratios to increase the number of images that can be stored.
89
Using the Menus: Shooting Mode
RAW RECORDING
Choose whether to compress RAW images.
Option
UNCOMPRESSED
Description
RAW images are not compressed.
RAW images are compressed using a reversible algorithm that reduces file size with no loss of image data.
LOSSLESS COMPRESSED The images can be viewed in RAW FILE CONVERTER EX 2.0 or other software that supports “lossless” RAW
compression (P 130).
FILM SIMULATION
Simulate the effects of different types of film (P 61).
GRAIN EFFECT
Add a film grain effect.
DYNAMIC RANGE
Control contrast. Choose lower values to increase contrast when shooting indoors or under overcast skies, higher values to
reduce loss of detail in highlights and shadows when photographing high-contrast scenes. Higher values are recommended
for scenes that include both sunlight and deep shade, for such high-contrast subjects as sunlight on water, brightly-lit autumn
leaves, and portraits taken against a blue sky, and for white objects or people wearing white; note, however, that mottling may
appear in pictures taken at higher values.
R If AUTO is selected, the camera will automatically choose either V 100% or W 200% according to the subject and shooting conditions. Shutter speed and aperture will be displayed when the shutter button is pressed halfway.
R W 200% is available at sensitivities of ISO 400 and above, X 400% at sensitivities of ISO 800 and above.
WHITE BALANCE
Adjust colors to match the light source (P 62).
90
Using the Menus: Shooting Mode
HIGHLIGHT TONE
Adjust the appearance of highlights.
SHADOW TONE
Adjust the appearance of shadows.
COLOR
Adjust color density.
SHARPNESS
Sharpen or soften outlines.
NOISE REDUCTION
Reduce noise in pictures taken at high sensitivities.
LONG EXPOSURE NR
Select ON to reduce mottling in long time-exposures (P 72).
Menus
LENS MODULATION OPTIMIZER
Select ON to improve definition by adjusting for diffraction and the slight loss of focus at the periphery of the lens.
COLOR SPACE
Choose the gamut of colors available for color reproduction.
Option
sRGB
Adobe RGB
Description
Recommended in most situations.
For commercial printing.
91
Using the Menus: Shooting Mode
PIXEL MAPPING
Use this option if you notice bright spots in your pictures.
1 Press MENU/OK in the shooting display and select the H IMAGE QUALITY SETTING tab (P 88).
2 Highlight PIXEL MAPPING and press MENU/OK to perform pixel mapping.
Q
Q
Q
Q
Results are not guaranteed.
Be sure the battery is fully charged before beginning pixel mapping.
Pixel mapping is not available when the camera temperature is elevated.
Processing may take a few seconds.
SELECT CUSTOM SETTING
Recall settings saved with EDIT/SAVE CUSTOM SETTING.
EDIT/SAVE CUSTOM SETTING
Save settings (P 83).
92
Using the Menus: Shooting Mode
G AF/MF SETTING
To adjust focus settings, press MENU/OK in the shooting display and select the
G (AF/MF SETTING) tab (P 88).
AF/MF SETTING
FOCUS AREA
AF MODE
AF-C CUSTOM SETTINGS
AF POINT DISPLAY
NUMBER OF FOCUS POINTS
PRE-AF
AF ILLUMINATOR
FACE/EYE DETECTION SETTING
EXIT
FOCUS AREA
Choose the focus area (P 69). Focus-area selection can also be used to choose the focus point for manual focus and focus zoom.
AF MODE
Choose the AF mode for focus modes S and C (P 67).
Menus
93
Using the Menus: Shooting Mode
AF-C CUSTOM SETTINGS
Select focus-tracking options for focus mode C. Choose from Sets 1–5 according to your subject.
AF-C CUSTOM SETTINGS
SET 1 STANDARD SETTING FOR MULTI-PURPOSE
OK
Option
SET 1 MULTI PURPOSE
SET 2 IGNORE OBSTACLES &
CONTINUE TO TRACK SUBJECT
SET 3 FOR ACCELERATING/
DECELERATING SUBJECT
SET 4 FOR SUDDENLY APPEARING
SUBJECT
SET 5 FOR ERRATICALLY MOVING &
ACCEL./DECEL. SUBJECT
Description
A standard tracking option that works well with the typical range of moving subjects.
The focus system attempts to track the chosen subject. Choose with subjects that are hard to
keep in the focus area or if other objects are likely to enter the focus area with the subject.
The focus system attempts to compensate for subject acceleration or deceleration. Choose for
subjects prone to rapid changes in velocity.
The focus system attempts to focus quickly on subjects entering the focus area. Choose for
subjects that appear abruptly or when rapidly switching subjects.
Choose for hard-to-track subjects prone not only to sudden changes in velocity but also to
large movements front to back and left to right.
AF POINT DISPLAY y z
Choose whether individual focus frames are displayed when ZONE or WIDE/TRACKING is selected for G AF/MF SETTING >
AF MODE.
NUMBER OF FOCUS POINTS
Choose the number of focus points available for focus-point selection in manual focus mode or when SINGLE POINT is selected
for AF MODE.
Option
91 POINTS (7 × 13)
325 POINTS (13 × 25)
94
Description
Choose from 91 focus points arranged in a 7- by 13-point grid.
Choose from 325 focus points arranged in a 13- by 25-point grid.
Using the Menus: Shooting Mode
PRE-AF
If ON is selected, the camera will continue to adjust focus even when the shutter-release button is not pressed halfway. Note
that this increases the drain on the battery.
AF ILLUMINATOR
If ON is selected, the AF-assist illuminator will light to assist autofocus.
Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to focus in macro
mode, try increasing the distance to the subject.
Q Avoid shining the AF-assist illuminator directly into your subject’s eyes.
Option
FACE ON/EYE OFF
FACE ON/EYE AUTO
FACE ON/RIGHT EYE PRIORITY
FACE ON/LEFT EYE PRIORITY
FACE OFF/EYE OFF
Menus
FACE/EYE DETECTION SETTING
Intelligent Face Detection sets focus and exposure for human faces anywhere in the frame, preventing the camera from focusing on the background in group portraits. Choose for shots that emphasize
portrait subjects. Faces can be detected with the camera in vertical or horizontal orientation; if a face is
detected, it will be indicated by a green border. If there is more than one face in the frame, the camera
will select the face closest to the center; other faces are indicated by white borders. You can also choose
whether the camera detects and focuses on eyes when Intelligent Face Detection is on. Choose from
the following options:
Description
Intelligent Face Detection only.
The camera automatically chooses which eye to focus on when a face is detected.
The camera focuses on the right eye of subjects detected using Intelligent Face Detection.
The camera focuses on the left eye of subjects detected using Intelligent Face Detection.
Intelligent Face Detection and eye priority off.
R If the camera is unable to detect the subject’s eyes because they are hidden by hair, glasses, or other objects, the camera will
instead focus on faces.
Q In some modes, the camera may set exposure for the frame as a whole rather than the portrait subject.
Q If the subject moves as the shutter button is pressed, the face may not be in the area indicated by the green border when
the picture is taken.
95
Using the Menus: Shooting Mode
AF+MF
If ON is selected in focus mode S, focus can be adjusted manually by rotating the focus ring while the shutter button is pressed
halfway. Both standard and focus peaking MF assist options are supported. Lenses with a focus distance indicator must be set
to manual focus mode (MF) before this option can be used. Selecting MF disables the focus distance indicator. Set the focus
ring to the center of the focus distance indicator, as the camera may fail to focus if the ring is set to infinity or the minimum
focus distance.
AF + MF Focus Zoom
When ON is selected for G AF/MF SETTING >
SETTING > FOCUS CHECK and SINGLE POINT selected for AF MODE
MODE,, focus zoom can be
used to zoom in on the selected focus area. Focus zoom is not available when ZONE or WIDE/TRACKING is selected for AF
MODE.. The zoom ratio (2.5× — 6×) can be selected using the rear command dial.
MODE
MF ASSIST
Choose how focus is displayed in manual focus mode (P 66).
Option
Description
STANDARD
Focus is displayed normally (focus peaking and digital split image are not available).
DIGITAL SPLIT IMAGE
A black-and-white (MONOCHROME) or color (COLOR) split-image display.
FOCUS PEAK HIGHLIGHT The camera heightens high-contrast outlines. Choose a color and peaking level.
FOCUS CHECK
If ON is selected, the camera will automatically zoom in on the view through the lens when the focus ring is rotated in manual
focus mode (P 65).
INTERLOCK SPOT AE & FOCUS AREA
Select ON to meter the current focus frame when SINGLE POINT is selected for AF MODE (P 67) and SPOT is selected for
PHOTOMETRY (P 60).
INSTANT AF SETTING
Choose how the camera focuses when the AF-L button is pressed in manual focus mode (P 64).
96
Using the Menus: Shooting Mode
DEPTH-OF-FIELD SCALE
Choose FILM FORMAT BASIS to help you make practical assessments of depth of field for pictures that will be viewed as prints
and the like, PIXEL BASIS to help you assess depth of field for pictures that will be viewed at high resolutions on computers or
other electronic displays.
RELEASE/FOCUS PRIORITY
Choose how the camera focuses in focus mode AF-S or AF-C.
Option
RELEASE
FOCUS
Description
Shutter response is prioritized over focus. Pictures can be taken when the camera is not in focus.
Focus is prioritized over shutter response. Pictures can be only taken when the camera is in focus.
Focus frame
Menus
CORRECTED AF FRAME
If ON is selected, a second focus frame for focus distances of about 50 cm (1.6 ft) will be added to the display in the optical viewfinder. The active focus frame is displayed in green when the shutter button is pressed halfway.
ON
OFF
Focus frame for focus distance of infinity
Active focus frame (displayed
in green when shutter button is pressed halfway)
Focus frame for focus distance of about 50 cm (1.6 ft)
Active focus frame
(displayed in green when shutter button is pressed halfway)
97
Using the Menus: Shooting Mode
A SHOOTING SETTING
To adjust shooting options, press MENU/OK in the shooting display and select the
A (SHOOTING SETTING) tab (P 88).
SHOOTING SETTING
SELF-TIMER
INTERVAL TIMER SHOOTING
AE BKT
FILM SIMULATION BKT
PHOTOMETRY
SHUTTER TYPE
IS MODE
ISO AUTO SETTING
EXIT
SELF-TIMER
Take pictures with the self-timer (P 74).
INTERVAL TIMER SHOOTING
Adjust settings for interval timer photography (P 75).
AE BKT
Adjust exposure bracketing settings.
Option
FRAMES/STEP SETTING
1 FRAME/CONTINUOUS
SEQUENCE SETTING
Description
Choose the number of shots in the bracketing sequence (FRAMES) and the amount exposure is varied
with each shot (STEP).
Choose whether the shots in the bracketing sequence are taken one at a time (1 FRAME) or in a single
burst (CONTINUOUS).
Choose the order in which the shots are taken.
FILM SIMULATION BKT
Choose film types for film simulation bracketing (P 55, 61).
PHOTOMETRY
Choose how the camera meters exposure (P 60).
98
Using the Menus: Shooting Mode
SHUTTER TYPE
Choose the shutter type. Choose the electronic shutter to mute the shutter sound.
Option
Description
Take pictures with the mechanical shutter.
t MECHANICAL SHUTTER
Take pictures with the electronic shutter.
s ELECTRONIC SHUTTER
t MECHANICAL + s ELECTRONIC The camera chooses the shutter type according to shooting conditions.
R If s ELECTRONIC SHUTTER or t MECHANICAL + s ELECTRONIC is selected, shutter speeds faster than 1/8,000 s can be
chosen by rotating the shutter speed dial to 8000 and then rotating the front command dial.
R When the electronic shutter is used, shutter speed and sensitivity are restricted to values of 1/32,000–1 s and ISO 12800–200
respectively, and long exposure noise reduction has no effect. In burst mode, focus and exposure are fixed at the values for
the first shot in each burst.
IS MODE
Reduce blur. This option is available only with lenses that support image stabilization.
Option
l CONTINUOUS
m SHOOTING ONLY
OFF
Menus
Q Distortion may be visible in shots of moving subjects with electronic shutter, while banding and fog may occur in shots taken
under fluorescent lights or other flickering or erratic illumination. When taking pictures with the shutter muted, respect your
subjects’ image rights and right to privacy.
Description
Image stabilization on.
Image stabilization enabled only when the shutter button is pressed halfway or the shutter is released.
Image stabilization off ; x appears in the display (P 8, 10). Recommended when using a tripod.
99
Using the Menus: Shooting Mode
ISO AUTO SETTING
Choose the base sensitivity, maximum sensitivity, and minimum shutter speed for auto ISO sensitivity control, which is selected
by rotating the ISO dial to A. Settings for AUTO1, AUTO2, and AUTO3 can be adjusted separately.
Item
DEFAULT SENSITIVITY
MAX. SENSITIVITY
MIN. SHUTTER SPEED
Options
12800–200
12800–400
1/500
500––1/4 SEC, AUTO
AUTO1
800
Default
AUTO2
200
1600
1/60 SEC
AUTO3
3200
The camera automatically chooses a sensitivity between the default and maximum values. Sensitivity is only raised above the
default value if the shutter speed required for optimal exposure would be slower than the value selected for MIN. SHUTTER
SPEED.
R If the value selected for DEFAULT SENSITIVITY is higher than that selected for MAX. SENSITIVITY, DEFAULT SENSITIVITY
will be set to the value selected for MAX. SENSITIVITY.
R The camera may select shutter speeds slower than MIN. SHUTTER SPEED if pictures would still be underexposed at the
value selected for MAX. SENSITIVITY. If AUTO is selected for MIN. SHUTTER SPEED, the camera will automatically choose a
minimum shutter speed approximately equal to the inverse of the lens’ focal length, in seconds (for example, if the lens has a
focal length of 50 mm, the camera will choose a minimum shutter speed in the neighborhood of 1/50 s). The minimum shutter
speed is not affected by the option selected for image stabilization.
MOUNT ADAPTOR SETTING
Adjust settings for M-mount lenses connected using an optional FUJIFILM M MOUNT ADAPTER (P 84).
WIRELESS COMMUNICATION
Connect to a smartphone or tablet over a wireless network (P 129).
R For more information, visit http://fujifilm-dsc.com/wifi/.
100
Using the Menus: Shooting Mode
F FLASH SETTING
To adjust flash-related settings, press MENU/OK in the shooting display and select
the F (FLASH SETTING) tab (P 88).
FLASH SETTING
FLASH FUNCTION SETTING
RED EYE REMOVAL
TTL-LOCK MODE
LED LIGHT SETTING
MASTER SETTING
CH SETTING
EXIT
FLASH FUNCTION SETTING
Choose a flash control mode, flash mode, or sync mode or adjust the flash level.
R The options available vary with the flash unit. See “Using Shoe-Mounted Flash Units” (P 143) for more information.
RED EYE REMOVAL
Remove red-eye effects caused by the flash.
Description
A red-eye reduction pre-flash is combined with digital red-eye removal.
Flash red-eye reduction only.
Digital red-eye removal only.
Flash red-eye reduction and digital red-eye removal off.
Menus
Option
FLASH + REMOVAL
FLASH
REMOVAL
OFF
R Flash red-eye reduction can be used in TTL flash control mode. Digital red-eye removal is performed only when a face is
detected and is not available with RAW images.
101
Using the Menus: Shooting Mode
TTL-LOCK MODE
Instead of adjusting flash level with each shot, TTL flash control can be locked for consistent results across a series of photographs.
Option
LOCK WITH LAST FLASH
LOCK WITH METERING FLASH
Description
Flash output is locked at the value metered for the most recent photo. An error message will be
displayed if no previously metered value exists.
The camera emits a series of pre-flashes and locks flash output at the metered value.
R To use TTL lock, assign TTL-LOCK to a camera control and then use the control to enable or disable TTL lock.
R Flash compensation can be adjusted while TTL lock is in effect.
LED LIGHT SETTING
Choose whether to use the flash unit’s LED video light (if available) as a catchlight or AF-assist illuminator when taking photos.
Option
CATCHLIGHT
AF ASSIST
AF ASSIST + CATCHLIGHT
OFF
Role of LED video light in still photography
Catchlight
AF-assist illuminator
AF-assist illuminator and catchlight
None
R This option can also be accessed via the flash settings menu.
102
Using the Menus: Shooting Mode
MASTER SETTING
Choose a flash group (A, B, or C) for the flash mounted on the camera hot shoe when it functions as a master flash controlling
remote flash units via FUJIFILM wireless optical flash control, or choose OFF to limit master flash output to a level that does not
affect the final picture.
R This option can also be accessed via the flash settings menu.
CH SETTING
Choose the channel used for communication between the master flash and remote flash units when using FUJIFILM optical
wireless flash control. Separate channels can be used for different flash systems or to prevent interference when multiple systems are operating in close proximity.
Menus
103
Using the Menus: Shooting Mode
B MOVIE SETTING
To adjust options for movie recording, press MENU/OK in the shooting display
and select the B (MOVIE SETTING) tab (P 88).
MOVIE SETTING
MOVIE MODE
MIC LEVEL ADJUSTMENT
MIC/REMOTE RELEASE
EXIT
MOVIE MODE
Select a frame size and rate for movie recording.
• i 1080/60 P: 1920 × 1080 (60 fps)
• i 1080/50 P: 1920 × 1080 (50 fps)
• i 1080/30 P: 1920 × 1080 (30 fps)
• i 1080/25 P: 1920 × 1080 (25 fps)
• i 1080/24 P: 1920 × 1080 (24 fps)
•
•
•
•
•
h 720/60 P: 1280 × 720 (60 fps)
h 720/50 P: 1280 × 720 (50 fps)
h 720/30 P: 1280 × 720 (30 fps)
h 720/25 P: 1280 × 720 (25 fps)
h 720/24 P: 1280 × 720 (24 fps)
MIC LEVEL ADJUSTMENT
Adjust the microphone recording level.
MIC/REMOTE RELEASE
Specify whether the device connected to the microphone/remote release connector is a microphone or a remote release (P 45,
73).
104
Using the Menus: Shooting Mode
E MY MENU
To display a personalized menu of frequently-used options, press MENU/OK in
the shooting display and select the E (MY MENU) tab (P 88).
R To edit “my menu”, select D USER SETTING > MY MENU SETTING (P 125).
R The E tab is only available if options have been assigned to MY MENU.
MY MENU
SELF-TIMER
INTERVAL TIMER SHOOTING
FILM SIMULATION BKT
PHOTOMETRY
SHUTTER TYPE
IS MODE
FACE/EYE DETECTION SETTING
ISO AUTO SETTING
EXIT
Menus
105
Using the Menus: Playback Mode
The playback menu is used to adjust playback settings.
Using the Playback Menu
1 Press MENU/OK in playback mode to display the
menus.
4 Press the selector up or down to
highlight the desired option.
PLAY BACK MENU
SWITCH SLOT
RAW CONVERSION
ERASE
CROP
RESIZE
PROTECT
IMAGE ROTATE
RED EYE REMOVA
5 Press MENU/OK to select the highlighted option.
EXIT
2 Press the selector up or down to
highlight the desired item.
3 Press the selector right to view options for the highlighted item.
106
6 Press DISP/BACK to return to the playback display.
R Use the front command dial to scroll through the
menus a page at a time.
Using the Menus: Playback Mode
C PLAY BACK MENU
To access playback options, press MENU/OK in the playback display and select
the C (PLAY BACK MENU) tab (P 106).
PLAY BACK MENU
SWITCH SLOT
RAW CONVERSION
ERASE
CROP
RESIZE
PROTECT
IMAGE ROTATE
RED EYE REMOVA
EXIT
SWITCH SLOT
Choose the card from which images will be played back (P 39).
RAW CONVERSION
Create JPEG copies of RAW pictures (P 82).
ERASE
Delete pictures (P 43).
1 Display the desired picture.
2 Select C CROP in the playback menu.
3 Use the rear command dial to zoom in and out and press the selector up, down, left, or right to scroll the picture until the
Menus
CROP
Create a cropped copy of the current picture.
desired portion is displayed.
4 Press MENU/OK to display a confirmation dialog.
5 Press MENU/OK again to save the cropped copy to a separate file.
R Larger crops produce larger copies; all copies have an aspect ratio of 3 : 2. If the size of the final copy will be a, OK will be
displayed in yellow.
107
Using the Menus: Playback Mode
RESIZE
Create a small copy of the current picture.
1 Display the desired picture.
2 Select C RESIZE in the playback menu.
3 Highlight a size and press MENU/OK to display a confirmation dialog.
4 Press MENU/OK again to save the resized copy to a separate file.
R The sizes available vary with the size of the original image.
PROTECT
Protect pictures from accidental deletion. Highlight one of the following options and press MENU/OK.
• FRAME: Protect selected pictures. Press the selector left or right to view pictures and press MENU/OK to select or deselect. Press
DISP/BACK when the operation is complete.
• SET ALL: Protect all pictures.
• RESET ALL: Remove protection from all pictures.
Q Protected pictures will be deleted when the memory card is formatted (P 114).
IMAGE ROTATE
Rotate pictures.
1 Display the desired picture.
2 Select C IMAGE ROTATE in the playback menu.
3 Press the selector down to rotate the picture 90° clockwise, up to rotate it 90° counterclockwise.
4 Press MENU/OK. The picture will automatically be displayed in the selected orientation whenever it is played back on the
camera.
R Protected pictures can not be rotated. Remove protection before rotating pictures.
R The camera may not be able to rotate pictures created with other devices. Pictures rotated on the camera will not be rotated
when viewed on a computer or on other cameras.
R Pictures taken with D SCREEN SETTING > AUTOROTATE PB are automatically displayed in the correct orientation during
playback (P 118).
108
Using the Menus: Playback Mode
RED EYE REMOVAL
Remove red-eye from portraits. The camera will analyze the image; if red-eye is detected, the image will be processed to create
a copy with reduced red-eye.
1 Display the desired picture.
2 Select C RED EYE REMOVAL in the playback menu.
3 Press MENU/OK.
R Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ depending on
the scene. Red eye can not be removed from pictures that have already been processed using red-eye removal or pictures
created with other devices.
R The amount of time needed to process the image varies with the number of faces detected.
R Copies created with RED EYE REMOVAL are indicated by a e icon during playback.
R Red eye removal can not be performed on RAW images.
Menus
109
Using the Menus: Playback Mode
VOICE MEMO SETTING
Add a voice memo to the current photograph.
1 Select ON for VOICE MEMO SETTING in the playback menu.
2 Display a photo to which you wish to add a voice memo.
3 Press and hold the center of the front command dial to record the memo. Recording ends after 30 s or when you release the
dial.
R The new memo will be recorded over any existing memos. Deleting the picture also deletes the memo.
R Voice memos can not be added to movies or protected pictures.
Playing Voice Memos
Pictures with voice memos are indicated by q icons during playback. To play a memo, select the picture and press the center
of the front command dial; a progress bar will be displayed while the memo plays back. Volume can be adjusted by pressing
MENU/OK to pause playback and then pressing the selector up or down to adjust the volume. Press MENU/OK again to resume
playback. Volume can also be adjusted using D SOUND SETTING >
SETTING > PLAYBACK VOLUME.
VOLUME.
110
Using the Menus: Playback Mode
COPY
Copy pictures between the cards in the first and second slots.
1 Select C COPY in the playback menu.
2 Highlight one of the following options and press the selector right:
• SLOT1 y SLOT2: Copy pictures from the card in the first slot to the card in the second slot.
• SLOT2 y SLOT1: Copy pictures from the card in the second slot to the card in the first slot.
3 Highlight one of the following options and press MENU/OK:
• FRAME: Copy selected pictures. Press the selector left or right to view pictures and press MENU/OK to copy the current picture.
• ALL FRAMES: Copy all pictures.
R Copying ends when the destination is full.
WIRELESS COMMUNICATION
Connect to a smartphone or tablet over a wireless network (P 129).
SLIDE SHOW
View pictures in an automated slide show. Press MENU/OK to start. Press DISP/BACK at any time during the show to view on-screen
help. The show can be ended at any time by pressing MENU/OK.
Menus
R For more information, visit http://fujifilm-dsc.com/wifi/.
R The camera will not turn off automatically while a slide show is in progress.
PHOTOBOOK ASSIST
Create books from your favorite photos (P 86).
111
Using the Menus: Playback Mode
PC AUTO SAVE
Upload pictures to a computer over a wireless network (P 129).
R For more information, visit http://fujifilm-dsc.com/wifi/.
PRINT ORDER (DPOF)
Select pictures for printing (P 133).
instax PRINTER PRINT
Print pictures on optional FUJIFILM instax SHARE printers (P 136).
DISP ASPECT
Choose how High Definition (HD) devices display pictures with an aspect ratio of 3 : 2
(this option is available only when an HDMI cable is connected). Select 16 : 9 to display
the image so that it fills the screen with its top and bottom cropped out, 3 : 2 to display
the entire image with black bands at either side.
112
16 : 9
3:2
16 : 9
3:2
The Setup Menu
View and adjust basic camera settings.
Using the Setup Menu
1 Press MENU/OK in shooting mode to display the
menus.
IMAGE QUALITY SETTING
IMAGE SIZE
IMAGE QUALITY
RAW RECORDING
FILM SIMULATION
GRAIN EFFECT
DYNAMIC RANGE
WHITE BALANCE
HIGHLIGHT TONE
5 Press the selector up or down to
highlight the category containing
the desired item.
6 Press the selector right to view the
option in the highlighted category.
EXIT
2 Press the selector left to highlight
the tab for the current menu.
7 Press the selector up or down to
highlight the desired item.
8 Press the selector right to view options for the highlighted item.
EXIT
Tab
Menus
SET UP
USER SETTING
SOUND SETTING
SCREEN SETTING
BUTTON/DIAL SETTING
POWER MANAGEMENT
SAVE DATA SETTING
CONNECTION SETTING
9 Press the selector up or down to
highlight the desired option.
3 Press the selector down to highlight
the D (SET UP) tab.
10 Press MENU/OK to select the highlighted option.
4 Press the selector right to display
setup menu categories.
11 Press DISP/BACK to return to the
shooting display.
R Use the front command dial to scroll through the
menus a page at a time.
113
The Setup Menu
D SET UP Menu Options
To access basic camera settings, press MENU/OK in the playback display and select the D (SET UP) tab (P 113).
SET UP
USER SETTING
SOUND SETTING
SCREEN SETTING
BUTTON/DIAL SETTING
POWER MANAGEMENT
SAVE DATA SETTING
CONNECTION SETTING
EXIT
■ D USER SETTING
FORMAT
To format a memory card:
1 Highlight D USER SETTING > FORMAT in the setup menu and press MENU/OK.
2 Highlight the slot containing the card you wish to format and press MENU/OK.
3 A confirmation dialog will be displayed. To format the memory card, highlight OK and press
MENU/OK. To exit without formatting the memory card, select CANCEL or press DISP/BACK.
Q All data—including protected pictures—will be deleted from the memory card. Be sure important files have been copied to a computer or other storage device.
Q Do not open the battery-chamber cover during formatting.
R The format menu can also be displayed by pressing the center of the rear command dial while
pressing and holding the b button.
DATE/TIME
Set the camera clock (P 26, 27).
114
FORMAT
FORMAT CARD IN SLOT 1, OK?
ERASE ALL DATA
OK
CANCEL
The Setup Menu
TIME DIFFERENCE
Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the
difference between local time and your home time zone:
1 Highlight g LOCAL and press MENU/OK.
2 Use the selector to choose the time difference between local time and your home time zone. Press MENU/OK when settings
are complete.
To set the camera clock to local time, highlight g LOCAL and press MENU/OK. To set the clock to the time in your home time
zone, select h HOME. If g LOCAL is selected, g will be displayed for three seconds when the camera is turned on.
a
Choose a language.
MY MENU SETTING
Edit “my menu” (P 125).
Menus
SENSOR CLEANING
Remove dust from the camera image sensor.
• OK: Clean sensor immediately (P xi).
• WHEN SWITCHED ON: If this option is selected, sensor cleaning will be performed when the camera turns on.
• WHEN SWITCHED OFF: If this option is selected, sensor cleaning will be performed when the camera turns off (sensor cleaning is
not however performed if the camera turns off in playback mode).
R Dust that can not be removed using sensor cleaning can be removed manually (P 150).
RESET
Reset shooting or setup menu options to default values. Custom white balance, custom settings banks created using EDIT/
SAVE CUSTOM SETTING, WIRELESS SETTINGS, and the setup menu DATE/TIME, TIME DIFFERENCE options are not affected.
1 Highlight the desired option and press the selector right.
2 A confirmation dialog will be displayed; highlight OK and press MENU/OK.
115
The Setup Menu
■ D SOUND SETTING
AF BEEP VOL.
Choose the volume of the beep that sounds when the camera focuses (P 76). The beep can be muted by selecting OFF.
SELF-TIMER BEEP VOL.
Choose the volume of the beep that sounds while the self-timer is active (P 74). The beep can be muted by selecting OFF.
OPERATION VOL.
Adjust the volume of the sounds produced when camera controls are operated. Choose e OFF (mute) to disable control
sounds.
SHUTTER VOLUME
Adjust the volume of the sounds produced when the shutter is released. Choose e OFF (mute) to disable the shutter sound.
SHUTTER SOUND
Choose the sound made by the shutter.
PLAYBACK VOLUME
Adjust the volume for movie playback.
116
The Setup Menu
■ D SCREEN SETTING
EVF BRIGHTNESS
Adjust the brightness of the display in the electronic viewfinder, or choose AUTO for automatic brightness adjustment.
EVF COLOR
Adjust the hue of the display in the electronic viewfinder.
LCD BRIGHTNESS
Adjust monitor brightness.
LCD COLOR
Adjust monitor hue.
IMAGE DISP.
Choose how long images are displayed after shooting. Colors may differ slightly from those in the final image and “noise” mottling may be visible at high sensitivities.
Option
1.5 SEC
0.5 SEC
OFF
Menus
CONTINUOUS
Description
Pictures are displayed until the MENU/OK button is pressed or the shutter button is pressed halfway. To zoom in
on the active focus point, press the center of the rear command dial; press again to cancel zoom.
Pictures are displayed for 1.5 seconds (1.5 SEC) or 0.5 seconds (0.5 SEC) or until the shutter button is pressed
halfway.
Pictures are not displayed after shooting.
EVF AUTOROTATE DISPLAYS
Choose whether the indicators in the viewfinder rotate to match camera orientation (P 31). Regardless of the option selected,
the indicators in the monitor do not rotate.
PREVIEW EXP./WB IN MANUAL MODE
Select PREVIEW EXP./WB to enable exposure and white balance preview in manual exposure mode (P 38), or choose PREVIEW
WB to preview only white balance. Select OFF when using a flash or on other occasions on which exposure may change when
the picture is taken.
117
The Setup Menu
PREVIEW PIC. EFFECT
Choose ON to preview the effects of film simulation, white balance, and other settings in the monitor. Choose OFF to make
shadows in low-contrast, back-lit scenes and other hard-to-see subjects more visible.
R If OFF is selected, the effects of camera settings will not be visible in the monitor and colors and tone will differ from those
in the final picture. The display will however be adjusted to show the effects of advanced filters and of monochrome and
sepia settings.
FRAMING GUIDELINE
Choose the type of framing grid available in shooting mode.
F GRID 9
P
For “rule of thirds” composition.
G GRID 24
H HD FRAMING
A six-by-four grid.
Frame HD pictures in the crop shown by the
lines at the top and bottom of the display.
P
P
AUTOROTATE PB
Choose ON to automatically rotate “tall” (portrait-orientation) pictures during playback.
FOCUS SCALE UNITS
Choose the units used for the focus distance indicator (P 65).
DISP. CUSTOM SETTING
Choose items for the standard display (P 33).
118
The Setup Menu
■ D BUTTON/DIAL SETTING
FOCUS LEVER SETTING
Choose the functions performed by the focus stick (focus lever).
Option
LOCK (OFF)
PUSH n TO UNLOCK
ON
Description
The focus stick can not be used during shooting.
Press the stick to view the focus-point display and tilt the stick to select a focus point.
Tilt the stick to view the focus-point display and select a focus point.
EDIT/SAVE QUICK MENU
Choose the options displayed in the quick menu (P 49).
FUNCTION (Fn) SETTING
Choose the roles played by the function buttons (P 51).
Y X S.S OPERATION
Select OFF to disable shutter-speed fine-tuning using the command dials.
Menus
COMMAND DIAL SETTING
Choose the roles played by the command dials.
ISO DIAL SETTING (H)
Choose the ISO sensitivity assigned to the H position on the ISO dial.
ISO DIAL SETTING (L)
Choose the ISO sensitivity assigned to the L position on the ISO dial.
SHOOT WITHOUT LENS
Choose whether shutter release is enabled when no lens is attached.
119
The Setup Menu
SHOOT WITHOUT CARD
Choose whether the shutter can be released without a memory card inserted in the camera.
Option
ON
OFF
Description
When no memory card is inserted, the shutter can be released to test camera function and the shooting
and setup menus can be displayed.
The shutter is disabled if no memory card is inserted, preventing accidental loss of pictures taken without
a memory card.
FOCUS RING
Choose the direction in which the focus ring is rotated to increase the focus distance.
AE-L/AF-L BUTTON SETTING
Switch the roles of the AF-L and AE-L buttons.
AE/AF-LOCK MODE
If AE & AF ON WHEN PRESSING is selected, exposure and/or focus will lock while the AE-L or AF-L button is pressed (P 77). If AE
& AF ON/OFF SWITCH is selected, exposure and/or focus will lock when the AE-L or AF-L button is pressed and remain locked
until the button is pressed again.
AF-LOCK MODE
Choose the role played by the AF-L button (P 77).
APERTURE SETTING
Choose the method used to adjust aperture when using lenses with no aperture rings.
• AUTO + o MANUAL: Rotate the rear command dial to choose the aperture. Rotate past minimum aperture to choose A (auto).
• AUTO: Aperture is selected automatically; camera functions in exposure mode P (program AE) or S (shutter-priority AE).
• MANUAL: Rotate the rear command dial to choose the aperture; camera functions in exposure mode A (aperture-priority AE)
or M (manual).
120
The Setup Menu
■ D POWER MANAGEMENT
AUTO POWER OFF
Choose the length of time before the camera turns off automatically when no operations are performed. Shorter times increase
battery life; if OFF is selected, the camera must be turned off manually. Note that in some situations the camera turns off automatically even when OFF is selected.
POWER MANAGEMENT
Adjust power management settings.
Option
HIGH PERFORMANCE
STANDARD
ECONOMY
AF performance (speed)
Fast
Fast
Normal
LCD/EVF display quality
Very high
High
Normal
Battery endurance
Low
Normal
High
Option
ON
OFF
Menus
R When ECONOMY is selected, the frame rate will drop when no operations are being performed. Operating camera controls
returns the frame rate to normal.
AUTO POWER SAVE
A power-saving option has been added for the LCD/EVF displays.
Description
When HIGH PERFORMANCE or STANDARD is selected for POWER MANAGEMENT, the LCD and EVF
will switch to a standard-quality display if no operations are performed for a set period. Operating camera
controls restores the high-quality display
Display quality does not change when no operations are performed.
121
The Setup Menu
■ D SAVE DATA SETTING
FRAME NO.
New pictures are stored in image files named using a four-digit file number assigned by adding one to the
Frame number
last file number used. The file number is displayed during playback as shown at right. FRAME NO. controls
100-0001
whether file numbering is reset to 0001 when a new memory card is inserted or the current memory card
is formatted.
Directory
File
number number
Option
Description
Numbering continues from the last file number used or the first available file number, whichever is higher. Choose
CONTINUOUS
this option to reduce the number of pictures with duplicate file names.
RENEW
Numbering is reset to 0001 after formatting or when a new memory card is inserted.
R If the frame number reaches 999-9999, the shutter release will be disabled (P 157).
R Selecting D USER SETTING > RESET (P 115) sets FRAME NO. to CONTINUOUS but does not reset the file number.
R Frame numbers for pictures taken with other cameras may differ.
SAVE ORG IMAGE
Choose ON to save unprocessed copies of pictures taken using F FLASH SETTING > RED EYE REMOVAL (P 101).
EDIT FILE NAME
Change the file name prefix. sRGB images use a four-letter prefix (default “DSCF”), Adobe RGB images a three-letter prefix (“DSF”)
preceded by an underscore.
122
The Setup Menu
CARD SLOT SETTING (STILL IMAGE)
Choose the role played by the card in the second slot.
Option
Description
SEQUENTIAL The card in the second slot is used only when the card in the first slot is full.
BACKUP
Each picture is recorded twice, once to each card.
As for SEQUENTIAL, except that the RAW copy of pictures taken with FINE + RAW or NORMAL + RAW selected
RAW / JPEG
for H IMAGE QUALITY SETTING > IMAGE QUALITY will be saved to the card in the first slot and the JPEG copy
to the card in the second slot.
R Regardless of the option selected for CARD SLOT SETTING (STILL IMAGE), movies will be recorded to the card in the first
slot; if SEQUENTIAL is selected, movies will be recorded to the card in the first slot even after recording has moved on to the
card in the second slot.
SWITCH SLOT (SEQUENTIAL)
Choose the card that is recorded to first when SEQUENTIAL is selected for CARD SLOT SETTING (STILL IMAGE).
Menus
COPYRIGHT INFO
Copyright information, in the form of Exif tags, can be added to new images as they are taken. Changes to copyright information
are reflected only in images taken after the changes are made.
Option
Description
DISP COPYRIGHT INFO
View the current copyright information.
ENTER AUTHOR’S INFO
Enter the creator’s name.
ENTER COPYRIGHT INFO
Enter the name of the copyright holder.
Delete the current copyright information. This change applies only to images taken after this option
DELETE COPYRIGHT INFO
is selected; copyright information recorded with existing images is not affected.
123
The Setup Menu
■ D CONNECTION SETTING
For more information on wireless connections, visit http://fujifilm-dsc.com/wifi/
WIRELESS SETTINGS
Adjust settings for connection to wireless networks.
Option
GENERAL SETTINGS
RESIZE IMAGE FOR SMARTPHONE H
PC AUTO SAVE SETTINGS
Description
Choose a name (NAME) to identify the camera on the wireless network (the camera is assigned a unique name by default) or select RESET WIRELESS SETTINGS to restore default
settings.
Choose ON (the default setting, recommended in most circumstances) to resize larger images to H for upload to smartphones, OFF to upload images at their original size. Resizing
applies only to the copy uploaded to the smartphone; the original is not affected.
Choose DELETE REGISTERED DESTINATION PC to remove selected destinations, DETAILS
OF PREVIOUS CONNECTION to view computers to which the camera has recently connected.
PC AUTO SAVE SETTING
Choose an upload destination. Choose SIMPLE SETUP to connect using WPS, MANUAL SETUP to configure network settings
manually.
GEOTAGGING SET-UP
View location data downloaded from a smartphone and choose whether to save the data with your pictures.
Option
GEOTAGGING
LOCATION INFO
Description
Choose whether location data downloaded from a smartphone are embedded in pictures as they are taken.
Display the location data last downloaded from a smartphone.
instax PRINTER CONNECTION SETTING
Adjust settings for connection to optional FUJIFILM instax SHARE printers (P 135).
124
“My Menu”
Selecting the E (MY MENU) tab displays a personalized custom menu of frequently-used options (P 105).
Editing “My Menu”
1 In the setup menu D USER SETTING tab,
highlight MY MENU SETTING and press
MENU/OK to display the following options
(P 113).
3 Highlight an item and press MENU/OK to add it
to “my menu”.
MY MENU SETTING
1 IMAGE SIZE
MY MENU SETTING
ADD ITEMS
RANK ITEMS
REMOVE ITEMS
MOVE
SAVE
4 Press MENU/OK to return to the edit display.
ADD ITEMS and press MENU/OK. Options that
can be added to “my menu” are highlighted in
blue.
R Options currently in “my menu” are indicated by
check marks.
5 Repeat Steps 3 and 4 until all the desired items
have been added.
R “My menu” can contain up to 16 items.
Menus
2 Press the selector up or down to highlight
Editing “My Menu”
To reorder or delete items, select RANK ITEMS or
REMOVE ITEMS in Step 1.
MY MENU SETTING
IMAGE SIZE
IMAGE QUALITY
RAW RECORDING
FILM SIMULATION
GRAIN EFFECT
DYNAMIC RANGE
WHITE BALANCE
HIGHLIGHT TONE
SELECT
CANCEL
125
Factory Defaults
The factory default settings for the options in the shooting and setup menus are listed below. These
settings can be restored using D USER SETTING > RESET (P 115).
■ Shooting Menu
Menu
H IMAGE QUALITY SETTING
IMAGE SIZE
IMAGE QUALITY
RAW RECORDING
FILM SIMULATION
GRAIN EFFECT
DYNAMIC RANGE
WHITE BALANCE
HIGHLIGHT TONE
SHADOW TONE
COLOR
SHARPNESS
NOISE REDUCTION
LONG EXPOSURE NR
LENS MODULATION OPTIMIZER
COLOR SPACE
SELECT CUSTOM SETTING
126
Default
O3:2
FINE
UNCOMPRESSED
PROVIA/STANDARD
OFF
100%
AUTO
0
0
0
0
0
ON
ON
sRGB
CUSTOM 1
Default
Menu
G AF/MF SETTING
AF MODE
AF-C CUSTOM SETTINGS
AF POINT DISPLAYyz
DISPLAYyz
NUMBER OF FOCUS POINTS
PRE-AF
AF ILLUMINATOR
FACE/EYE DETECTION SETTING
AF+MF
MF ASSIST
FOCUS CHECK
INTERLOCK SPOT AE & FOCUS
AREA
INSTANT AF SETTING
DEPTH-OF-FIELD SCALE
RELEASE/FOCUS PRIORITY
• AF-S PRIORITY SELECTION
• AF-C PRIORITY SELECTION
CORRECTED AF FRAME
SINGLE POINT
SET 1
OFF
91 POINTS (7×13)
OFF
ON
FACE OFF/EYE OFF
OFF
STANDARD
OFF
ON
AF-S
PIXEL BASIS
RELEASE
RELEASE
OFF
Factory Defaults
Default
Menu
■ Setup Menu
Default
Menu
OFF
PROVIA/STANDARD
Velvia/VIVID
ASTIA/SOFT
MULTI
MECHANICAL SHUTTER
CONTINUOUS
AUTO1
0
LENS 5 (50mm)
F FLASH SETTING
RED EYE REMOVAL
TTL-LOCK MODE
OFF
LOCK WITH LAST FLASH
B MOVIE SETTING
MOVIE MODE
MIC LEVEL ADJUSTMENT
MIC/REMOTE RELEASE
i 1080/60P
3
MIC
D USER SETTING
TIME DIFFERENCE
SENSOR CLEANING
• WHEN SWITCHED ON
• WHEN SWITCHED OFF
OFF
ON
D SOUND SETTING
AF BEEP VOL.
SELF-TIMER BEEP VOL.
OPERATION VOL.
SHUTTER VOLUME
SHUTTER SOUND
PLAYBACK VOLUME
c
c
OFF
c
SOUND 1
7
D SCREEN SETTING
EVF BRIGHTNESS
EVF COLOR
LCD BRIGHTNESS
LCD COLOR
IMAGE DISP.
EVF AUTOROTATE DISPLAYS
PREVIEW EXP./WB IN MANUAL
MODE
PREVIEW PIC. EFFECT
FRAMING GUIDELINE
AUTOROTATE PB
FOCUS SCALE UNITS
DISP. CUSTOM SETTING
HOME
AUTO
0
0
0
OFF
ON
PREVIEW EXP./WB
Menus
G SHOOTING SETTING
SELF-TIMER
FILM SIMULATION BKT
• FILM 1
• FILM 2
• FILM 3
PHOTOMETRY
SHUTTER TYPE
IS MODE
ISO AUTO SETTING
MOUNT ADAPTOR SETTING
• BRIGHT FRAME BRIGHTNESS
• LENS REGISTRATION
ON
GRID 9
OFF
METERS
See page 33.
127
Factory Defaults
Menu
D BUTTON/DIAL SETTING
FOUCS LEVER SETTING
EDIT/SAVE QUICK MENU
FUNCTION (Fn) SETTING
COMMAND DIAL SETTING
Y X S.S OPERATION
ISO DIAL SETTING (H)
ISO DIAL SETTING (L)
SHOOT WITHOUT LENS
SHOOT WITHOUT CARD
FOCUS RING
AE-L/AF-L BUTTON SETTING
AE/AF-LOCK MODE
AF-LOCK MODE
APERTURE SETTING
D POWER MANAGEMENT
AUTO POWER OFF
POWER MANAGEMENT
AUTO POWER SAVE
128
Default
ON
See page 47.
See page 50.
Y S.S. X F
ON
25600
100
OFF
ON
X CW
AE-L/AF-L
AE&AF ON WHEN PRESSING
AF LOCK ONLY
AUTO + MANUAL
2 MIN
STANDARD
OFF
Default
Menu
D SAVE DATA SETTING
FRAME NO.
SAVE ORG IMAGE
CARD SLOT SETTING
(STILL IMAGE)
D CONNECTION SETTING
WIRELESS SETTINGS
• RESIZE IMAGE FOR
SMARTPHONE H
PC AUTO SAVE SETTING
GEOTAGGING SET-UP
• GEOTAGGING
• LOCATION INFO
CONTINUOUS
OFF
SEQUENTIAL
ON
SIMPLE SETUP
ON
ON
Connections
Wireless Transfer (FUJIFILM Camera Remote/FUJIFILM PC AutoSave)
Access wireless networks and connect to computers, smartphones, or tablets. For downloads and other information, visit http://fujifilm-dsc.com/wifi/.
fujifilm Wi-Fi app
Wireless Connections: Computers
Once you have installed the “FUJIFILM PC AutoSave”
application and configured your computer as a
destination for the images copied from the camera, you can upload pictures from the camera using
C PLAY BACK MENU > PC AUTO SAVE (P 112) or
by pressing and holding the function button (Fn1)
in playback mode.
Connections
Wireless Connections: Smartphones
Install the “FUJIFILM Camera Remote” app on your
smartphone to browse the images on the camera, download selected images, control the camera remotely, or copy location data to the camera.
To connect to the smartphone, set the camera
to playback mode and press the function button
(Fn1).
R You can also connect using A SHOOTING
SETTING/C PLAY BACK MENU > WIRELESS
COMMUNICATION (P 100, 111).
129
Viewing Pictures on a Computer (MyFinePix Studio/RAW FILE CONVERTER EX 2.0)
Read this section for information on copying pictures to a computer.
Windows
Use MyFinePix Studio to copy pictures to your computer, where they can be stored, viewed, organized,
and printed. MyFinePix Studio is available for download from the following website:
http://fujifilm-dsc.com/mfs/
fujifilm mfs
Once download is complete, double-click the downloaded file (“MFPS_Setup.EXE”) and follow the
on-screen instructions to complete installation. Proceed to “Connecting the Camera” (P 131) when
installation is complete.
Mac OS X/macOS
Pictures can be copied to your computer using Image Capture (supplied with your computer) or other
software. Proceed to “Connecting the Camera” (P 131).
Viewing RAW Files
To view RAW files on your computer, use the RAW FILE CONVERTER EX 2.0, available for download from:
http://fujifilm-dsc.com/rfc/
fujifilm rfc
130
Viewing Pictures on a Computer
Connecting the Camera
1 Find a memory card containing pictures you want to copy to the computer and insert the card into
the camera.
Q Loss of power during transfer could result in loss of data or damage to the memory card. Insert a fresh or
fully-charged battery before connecting the camera.
2 Turn the camera off and connect a USB cable (available
separately from third-party suppliers) as shown, making
sure the connectors are fully inserted. Connect the camera directly to the computer; do not use a USB hub or keyboard.
3 Turn the camera on.
Connections
Q The USB cable must be no more than 1.5 m (4.9 ft.) long and be
suitable for data transfer.
Q Connect to camera Micro USB (Micro-B) connector.
Q The camera uses a Micro-B USB 2.0 connector.
4 Copy pictures to the computer using MyFinePix Studio or applications provided with your operating system.
For more information on using the software, start the application and select the appropriate option
from the Help menu.
131
Viewing Pictures on a Computer
Q If a memory card containing a large number of images is inserted, there may be a delay before the software
starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
Q Make sure that the computer does not display a message stating that copying is in progress and that the indicator lamp is out before turning the camera off or disconnecting the USB cable (if the number of images copied is very large, the indicator lamp may remain lit after the message has cleared from the computer display).
Failure to observe this precaution could result in loss of data or damage to the memory card.
Q Disconnect the camera before inserting or removing memory cards.
Q In some cases, it may not be possible to access pictures saved to a network server using the software in the
same way as on a standalone computer.
Q The user bears all applicable fees charged by the phone company or Internet service provider when using
services that require an Internet connection.
Disconnecting the Camera
After confirming that the indicator lamp is out, turn the camera off and disconnect the USB cable.
132
Creating a DPOF Print Order
The C PLAY BACK MENU > PRINT ORDER (DPOF) (P 112) option can be used to create a digital “print
order” for DPOF-compatible printers.
DPOF
DPOF (Digital Print Order Format) is standard that allows pictures to be printed from “print orders”
stored on the memory card. The information in the order includes the pictures to be printed and the
number of copies of each picture.
PLAY BACK MENU
COPY
WIRELESS COMMUNICATION
WITH DATE
SLIDE SHOW
WITHOUT DATE
PHOTOBOOK ASSIST
RESET ALL
PC AUTO SAVE
PRINT ORDER(DPOF)
PRINTER PRINT
DISP ASPECT
WITH DATE s: Print date of
recording on pictures.
WITHOUT DATE: Print pictures
without date.
Press MENU/OK and follow the steps below.
1 Press the selector left or right to display a picture you wish to include in
or remove from the print order.
2 Press the selector up or down to
choose the number of copies (up
to 99). To remove a picture from the
order, press the selector down until
the number of copies is 0.
PRINT ORDER (DPOF)
DPOF: 00001
Connections
■ WITH DATE s/ WITHOUT DATE
To modify the DPOF print order, select C PLAY
BACK MENU > PRINT ORDER (DPOF) (P 106)
and press the selector up or down to highlight
WITH DATE s or WITHOUT DATE.
Total number of prints
Number of copies
01 SHEETS
FRAME
SET
133
Creating a DPOF Print Order
3 Repeat steps 1–2 to complete the
print order. Press MENU/OK to save
the print order when settings are
complete, or DISP/BACK to exit without changing the print order.
4 The total number of prints is displayed in the monitor. Press MENU/OK
to exit.
The pictures in the current
print order are indicated by a
u icon during playback.
134
■ RESET ALL
To cancel the current print
order, select RESET ALL for
C PLAY BACK MENU > PRINT
ORDER (DPOF) (P 106). The
confirmation shown at right
will be displayed; press MENU/OK
to remove all pictures from the
order.
RESET DPOF OK?
YES
CANCEL
R Print orders can contain a maximum of 999 pictures.
RESET DPOF OK?
R If a memory card is inserted
containing a print order created by another camera, the
message shown at right will
YES
NO
be displayed. Pressing MENU/OK
cancels the print order; a new
print order must be created as
described above.
instax SHARE Printers
Print pictures from your digital camera to instax SHARE printers.
Establishing a Connection
Select D CONNECTION SETTING > instax PRINTER CONNECTION SETTING (P 124) and enter the
instax SHARE printer name (SSID) and password.
The Printer Name (SSID) and Password
The printer name (SSID) can be found on the bottom of the printer; the default password is “1111”. If you have already chosen a different password to
print from a smartphone, enter that password instead.
Connections
135
instax SHARE Printers
Printing Pictures
1 Turn the printer on.
3 Use the selector to display the picture you
want to print, then press MENU/OK.
PRINTER PRINT
TRANSMIT
instax-12345678
2 Select C PLAY BACK MENU > instax PRINTER PRINT (P 106). The camera will connect to
the printer.
100-0020
CANCEL
R Pictures taken with other cameras can not be
printed.
R The area printed is smaller than the area visible
in the LCD monitor.
PRINTER PRINT
instax-12345678
CONNECTING TO PRINTER
FUJIFILM-CAMERA-1234
4 The picture will be sent to the printer and
printing will start.
CANCEL
R To print a frame from a burst sequence, display
the frame before selecting instax PRINTER
PRINT.
PRINTER PRINT
instax-12345678
SENDING
FUJIFILM-CAMERA-1234
CANCEL
136
Viewing Pictures on TV
To show pictures to a group, connect the camera to a TV using an HDMI cable (available separately
from third-party suppliers; note that the TV can only be used for playback, not shooting).
1 Turn the camera off.
2 Connect the cable as shown below, making sure the connectors are fully inserted in the correct
orientation.
Insert into
HDMI connector
Q Use an HDMI cable no more than 1.5 m (4.9 ft.) long with a type D (HDMI Micro) connector for connection
to the camera.
R Be sure the connectors are fully inserted.
Connections
Insert into Micro HDMI
(Type D) connector
3 Tune the television to the HDMI input channel. See the documentation supplied with the television for details.
4 Turn the camera on and press a button. The camera monitor turns off and pictures and movies
are played back on the TV. Note that the camera volume controls have no effect on sounds played
on the TV; use the television volume controls to adjust the volume.
R The USB cable can not be used while an HDMI cable is connected.
R Some televisions may briefly display a black screen when movie playback begins.
137
Technical Notes
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.com/
products/digital_cameras/index.html.
Rechargeable Li-ion batteries
NP-W126/NP-W126S: Additional large-capacity NP-W126/NP-W126S rechargeable batteries can be purchased
as required.
Battery chargers
BC-W126: Replacement battery chargers can be purchased as required. At +20 °C/+68 °F, the BC-W126
charges an NP-W126/NP-W126S in about 150 minutes.
AC power adapters
AC-9V (requires CP-W126 DC coupler): Use for extended shooting and playback or when copying pictures to a computer.
DC couplers
CP-W126: Connect the AC-9V to the camera.
138
Optional Accessories
Remote releases
RR-90: Use to reduce camera shake or keep the shutter open during a time exposure.
Stereo microphones
MIC-ST1: An external microphone for movie recording.
FUJINON lenses
XF-series lenses: Interchangeable lenses for use exclusively with the FUJIFILM X-mount.
XC-series lenses: Interchangeable lenses for use exclusively with the FUJIFILM X-mount.
Technical Notes
139
Optional Accessories
Shoe-mounted flash units
EF-X500: This clip-on flash unit has a Guide Number of 50/164 (ISO 100, m/ft.) and supports FP (high-speed
sync), allowing it to be used at shutter speeds that exceed the flash sync speed. Powered by four AA batteries or an optional BF-BP1 battery pack, it supports manual and TTL flash control and auto power zoom
in the range 24–105 mm (35 mm format equivalent) and features FUJIFILM optical wireless flash control,
allowing it to be used as a master or remote flash unit for remote wireless flash photography. The flash
head can be rotated 90° up, 10° down, 135° left, or 180° right for bounce lighting.
EF-42: This clip-on flash unit (powered by four AA batteries) has a Guide Number of 42/137 (ISO 100, m/ft.)
and supports TTL flash control and auto power zoom in the range 24–105 mm (35 mm format equivalent).
The flash head can be rotated 90° up, 180° left, or 120° right for bounce lighting.
EF-X20: This clip-on flash unit has a Guide Number of 20/65 (ISO 100, m/ft.).
EF-20: This clip-on flash unit (powered by two AA batteries) has a Guide Number of 20/65 (ISO 100, m/ft.) and
supports TTL flash control. The flash head can be rotated upwards 90° for bounce lighting.
Grips
MHG-XPRO2: Features an improved grip. Batteries and memory cards can be removed with the grip in place, and the grip is
equipped with a rail for quick-shoe camera mounts. The tripod mount can be aligned with the lens optical axis.
Leather cases
BLC-XPRO2: This case combines practicality with the luxury of leather and comes with a cloth that can be used to wrap the
camera before putting it in the case and on other occasions. Pictures can be taken and batteries inserted or removed with the
camera still in its case.
140
Optional Accessories
Grip belt
GB-001: GB-001 enhances the camera’s hold, allowing users to carry the camera firmly with just one hand.
Macro extension tubes
MCEX-11/16: Attach between the camera and the lens to shoot at high reproduction ratios.
Protective filters
PRF-39/PRF-43/PRF-52/PRF-58/PRF-62/PRF-67/PRF-72/PRF-77: Use to protect the lens.
Teleconverters
XF1.4X TC WR: Increases the focal length of the lens by about 1.4×.
Mount adapters
FUJIFILM M MOUNT ADAPTER: Allows the camera to be used with a wide selection of M-mount lenses.
Front lens caps
FLCP-39/FLCP-43/FLCP-52/FLCP-58/FLCP-62/FLCP-67/FLCP-72/FLCP-72 II/FLCP-77: Protect the front lens element when the lens is not in use.
Body caps
BCP-001: Cover the camera lens mount when no lens is attached.
instax SHARE printers
SP-1/SP-2: Connect via wireless LAN to print pictures on instax film.
Technical Notes
Rear lens caps
RLCP-001: Protect the rear lens element when the lens is not attached to the camera.
141
Optional Accessories
Connecting the Camera to Other Devices
■ Remote Shutter
Release
■ External
Microphones
Shoe mount flash *
MIC-ST1 stereo
microphone *
RR-90 remote release *
■ Printing
X-Pro2
instax SHARE printer *
Wireless LAN
EF-X500
EF-42
EF-X20
XC-series lenses *
■ Macro Extension Tube
MCEX-11/16 *
SP-1
■ M Mount Adapter
■ Computer Related
FUJIFILM M MOUNT ADAPTER *
USB cable †
■ Audio/Visual
Computer †
* Available separately from FUJIFILM.
† Available separately from third-party suppliers. USB cables
must be no more than 1.5 m (4.9 ft.) long, HDMI cables no
more than 1.5 m (4.9 ft.) long.
142
EF-20
■ Lens
XF-series lenses *
SD/SDHC/SDXC
memory card †
SP-2
■ Flash Photography
HDMI cable †
HDTV †
Optional Accessories
Using Shoe-Mounted Flash Units
External flash units are more powerful than their built-in counterparts. Some support high-speed sync
(FP) and can be used at shutter speeds faster than the flash sync speed, while others can function as
master flash units controlling remote units via optical wireless flash control.
Q Test firing may sometimes be unavailable, for example when the camera setup menu is displayed.
Connect the flash unit and select F FLASH SETTING > FLASH FUNCTION SETTING
in the camera shooting menu to display flash options. The options available vary with
the status of the connected unit.
FLASH SETTING
FLASH FUNCTION SETTING
RED EYE REMOVAL
TTL-LOCK MODE
LED LIGHT SETTING
MASTER SETTING
CH SETTING
EXIT
Option
SYNC TERMINAL
SHOE MOUNT FLASH
SUPPLIED FLASH
R SYNC TERMINAL will also be displayed if the flash is attached but not raised.
Technical Notes
MASTER (OPTICAL)
Description
Available with units connected via the sync terminal and with third-party and other units that use only the
X-contact on the hot shoe. Also displayed if no flash unit is connected (P 144).
Displayed when an optional flash unit is mounted on the hot shoe and turned on (P 144).
Displayed if an optional flash unit functioning as a master flash for FUJIFILM optical wireless remote flash
control is connected and turned on (P 146).
Displayed when the EF-X8 flash unit supplied with FUJIFILM X-T1 and X-T2 cameras is connected and raised
(P 148).
143
Optional Accessories
■ SYNC TERMINAL
The following options are
available when a flash unit
is connected via the sync
terminal.
■ SHOE MOUNT FLASH
The following options are
available when an optional
shoe-mounted flash unit is
attached and turned on.
MODE
SYNC TERMINAL
ADJUST
END
A Flash control mode: Choose from the options below.
• M: A trigger signal is transmitted from the sync terminal
and hot shoe when a picture is taken. Choose a shutter
speed slower than the sync speed; even slower speeds
may be required if the unit uses long flashes or has a
slow response time.
• D (OFF): The sync terminal and hot shoe do not transmit a trigger signal.
B Sync: Choose whether the flash is timed to fire immediately
after the shutter opens (H/1ST CURTAIN) or immediately
before it closes (I/2ND CURTAIN). 1ST CURTAIN is recommended in most circumstances.
The Sync Terminal
Use the sync terminal to connect
flash units that require a sync cable.
144
MODE
SHOE MOUNT FLASH
ADJUST
END
A Flash control mode: The flash control mode selected with the
flash unit. This can in some cases be adjusted from the
camera; the options available vary with the flash.
• TTL: TTL mode. Adjust flash compensation (B).
• M: The flash fires at the selected output regardless of subject brightness or camera settings. Output in some cases
can be adjusted from the camera (B).
• MULTI: Repeating flash. Compatible shoe-mounted flash
units will fire multiple times with each shot.
• D (OFF): The flash does not fire. Some flash units can
be turned off from the camera.
B Flash compensation/output: The options available vary with
flash control mode.
• TTL: Adjust flash compensation (the full value may not
be applied if the limits of the flash control system are
exceeded). In the cases of the EF-X20, EF-20, and EF-42,
the selected value is added to the value selected with
the flash unit.
• M/MULTI: Adjust flash output (compatible units only).
Choose from values expressed as fractions of full power, from 1/1 (mode M) or 1/4 (MULTI) down to 1/512 in increments equivalent to 1/3 EV. The desired results may not
be achieved at low values if they exceed the limits of the
flash control system; take a test shot and check the results.
Optional Accessories
C Flash mode (TTL): Choose a flash mode for TTL flash control.
F Lighting: If the unit supports this feature, choose from the
The options available vary with the shooting mode (P, S, A,
or M) selected.
• E (FLASH AUTO): The flash fires only as required; flash level is adjusted according to subject brightness. A p icon
displayed when the shutter button is pressed halfway
indicates that the flash will fire when the photo is taken.
• F (STANDARD): The flash fires with every shot if possible;
flash level is adjusted according to subject brightness.
The flash will not fire if not fully charged when the shutter is released.
• G (SLOW SYNC.): Combine the flash with slow shutter
speeds when photographing portrait subjects against a
backdrop of night scenery. The flash will not fire if not
fully charged when the shutter is released.
options below.
• J (FLASH POWER PRIORITY): Gain range by slightly reducing coverage.
• K (STANDARD): Match coverage to picture angle.
• L (EVEN COVERAGE PRIORITY): Slightly increase coverage
for more even lighting.
Choose how the built-in LED light functions
during still photography (compatible units only). It can
function as a catchlight (M/CATCHLIGHT), as an AF-assist
illuminator (N/AF ASSIST), or as both a catchlight and an
AF-ASSIST illuminator (O/AF ASSIST+CATCHLIGHT). Choose
OFF to disable the LED during photography.
G Number of flashes: Choose the number of times the flash
fires each time the shutter is released in MULTI mode. *
H Frequency: Choose the frequency at which the flash fires in
MULTI mode. *
* Full value may not be applied if limits of flash control system are
exceeded.
Technical Notes
D Sync: Control flash timing.
• H (1ST CURTAIN): The flash fires immediately after the
shutter opens (generally the best choice).
• I (2ND CURTAIN): The flash fires immediately before the
shutter closes.
• R (AUTO FP(HSS)): High-speed sync (compatible units
only). The camera automatically engages front-curtain
high-speed sync at shutter speeds faster than the flash
sync speed. Equivalent to 1ST CURTAIN when MULTI is selected for flash control mode.
G LED light:
E Zoom: The angle of illumination (flash coverage) for units
that support flash zoom. Some units allow the adjustment to be made from the camera. If AUTO is selected,
zoom will automatically be adjusted to match coverage
to lens focal length.
145
Optional Accessories
■ MASTER (OPTICAL)
The options at right will be
displayed if the unit is currently functioning as master flash for FUJIFILM optical wireless remote flash
control.
A Flash control mode (group A)/B Flash control mode (group B)/
C Flash control mode (group C): Choose flash control modes
MODE
MASTER(OPTICAL)
ADJUST
END
The master and remote
units can be placed in up
C
to three groups (A, B, and
C) and flash mode and A
flash level adjusted sepaB
rately for each group. Four
channels are available
for communication between the units; separate
channels can be used for different flash systems
or to prevent interference when multiple systems
are operating in close proximity.
146
for groups A, B, and C. TTL% is available for groups A and
B only.
• TTL: The units in the group fire in TTL mode. Flash compensation can be adjusted separately for each group.
• TTL%: If TTL% is selected for either group A or B, you can
specify the output of the selected group as a percentage
of the other and adjust overall flash compensation for
both groups.
• M: In mode M, the units in the group fire at the selected
output (expressed as a fraction of full power) regardless
of subject brightness or camera settings.
• MULTI: Choosing MULTI for any group sets all the units in
all groups to repeating flash mode. All units will fire multiple times with each shot.
• D (OFF): If OFF is selected, the units in the group will
not fire.
D Flash
compensation/output (group A)/E Flash compensation/
output (group B)/F Flash compensation/output (group C): Adjust flash level for the selected group according to option
selected for flash control mode. Note that the full value
may not be applied if the limits of the flash control system
are exceeded.
• TTL: Adjust flash compensation.
• M/MULTI: Adjust flash output.
• TTL%: Choose the balance between groups A and B and
adjust overall flash compensation.
Optional Accessories
G Flash mode (TTL): Choose a flash mode for TTL flash control.
J Lighting: If the unit supports this feature, choose from the
The options available vary with the shooting mode (P, S, A,
or M) selected.
• E (FLASH AUTO): The flash fires only as required; flash level is adjusted according to subject brightness. A p icon
displayed when the shutter button is pressed halfway
indicates that the flash will fire when the photo is taken.
• F (STANDARD): The flash fires with every shot if possible;
flash level is adjusted according to subject brightness.
The flash will not fire if not fully charged when the shutter is released.
• G (SLOW SYNC.): Combine the flash with slow shutter
speeds when photographing portrait subjects against a
backdrop of night scenery. The flash will not fire if not
fully charged when the shutter is released.
options below.
• J (FLASH POWER PRIORITY): Gain range by slightly reducing coverage.
• K (STANDARD): Match coverage to picture angle.
• L (EVEN COVERAGE PRIORITY): Slightly increase coverage
for more even lighting.
or C (Gr C). If OFF is selected, output from the master flash
will be held to a level that does not affect the final picture.
Available only if the unit is mounted on the camera hot
shoe as a master flash for FUJIFILM optical wireless remote
flash control in TTL, TTL%, or M mode.
K Number of flashes: Choose the number of times the flash
fires each time the shutter is released in MULTI mode.
L Channel: Choose the channel used by the master flash for
communication with the remote flash units. Separate
channels can be used for different flash systems or to prevent interference when multiple systems are operating in
close proximity.
L Frequency: Choose the frequency at which the flash fires
in MULTI mode.
Technical Notes
H Sync: Control flash timing.
• H (1ST CURTAIN): The flash fires immediately after the
shutter opens (generally the best choice).
• I (2ND CURTAIN): The flash fires immediately before the
shutter closes.
• R (AUTO FP(HSS)): High-speed sync (compatible units
only). The camera automatically engages front-curtain
high-speed sync at shutter speeds faster than the flash
sync speed. Equivalent to 1ST CURTAIN when MULTI is selected for flash control mode.
K Master: Assign the master flash to group A (Gr A), B (Gr B),
I Zoom: The angle of illumination (flash coverage) for units
that support flash zoom. Some units allow the adjustment
to be made from the camera. If AUTO is selected, zoom will
automatically be adjusted to match coverage to lens focal
length.
147
Optional Accessories
■ SUPPLIED FLASH
Displayed when the EF-X8 flash
unit supplied with FUJIFILM X-T1
and X-T2 cameras is connected
and raised.
C Flash mode (TTL): Choose a flash mode for TTL flash control.
MODE
SUPPLIED FLASH
ADJUST
END
A Flash control mode: Choose from the following options.
• TTL: TTL mode. Adjust flash compensation (B) and
choose a flash mode (C).
• M: The flash fires at the selected output (B) regardless
of subject brightness or camera settings. Output is expressed in fractions of full power, from 1/1 to 1/64. The desired results may not be achieved at low values if they
exceed the limits of the flash control system; take a test
shot and check the results.
• C (COMMANDER): Choose if the flash is being used to control remote synced flash units, for example as part of a
studio flash system.
• D (OFF): The flash does not fire. Flash units connected
via the sync terminal will still fire when the shutter is released, but can be disabled by lowering the EF-X8 and
turning the units off in the flash settings menu.
B Flash compensation/output:
Adjust flash level. The options
available vary with the flash control mode (A).
148
The options available vary with the shooting mode (P, S, A,
or M) selected.
• E (FLASH AUTO): The flash fires only as required; flash level is adjusted according to subject brightness. A p icon
displayed when the shutter button is pressed halfway
indicates that the flash will fire when the photo is taken.
• F (STANDARD): The flash fires with every shot if possible;
flash level is adjusted according to subject brightness.
The flash will not fire if not fully charged when the shutter is released.
• G (SLOW SYNC.): Combine the flash with slow shutter
speeds when photographing portrait subjects against a
backdrop of night scenery. The flash will not fire if not
fully charged when the shutter is released.
D Sync: Choose whether the flash is timed to fire immediately
after the shutter opens (H/1ST CURTAIN) or immediately
before it closes (I/2ND CURTAIN). 1ST CURTAIN is recommended in most circumstances.
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
■ Water and Sand
Exposure to water and sand can also damage the
camera and its internal circuitry and mechanisms.
When using the camera at the beach or seaside,
avoid exposing the camera to water or sand. Do
not place the camera on a wet surface.
■ Condensation
Sudden increases in temperature, such as occur
when entering a heated building on a cold day,
can cause condensation inside the camera. If this
occurs, turn the camera off and wait an hour before turning it on again. If condensation forms on
the memory card, remove the card and wait for
the condensation to dissipate.
Traveling
Keep the camera in your carry-on baggage.
Checked baggage may suffer violent shocks that
could damage the camera.
Technical Notes
Use and Storage Precautions
If the camera will not be used for an extended period, remove the battery and memory card. Do
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very high temperatures, such as in a closed vehicle on a very
hot day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields, such as near
a broadcasting antenna, power line, radar emitter, motor, transformer, or magnet
• in contact with volatile chemicals such as pesticides
• in contact with rubber or vinyl products
149
Cleaning the Image Sensor
Multiple photographs marred by spots or blotches in identical locations may indicate the presence of
dust on the camera image sensor. Clean the sensor using D USER SETTING > SENSOR CLEANING
(P 115); if the problem persists, you can clean the sensor manually as described below. Note that there
will be a charge to repair or replace the image sensor if it is damaged during cleaning.
1 Use a blower (not a brush) to remove dust from the sensor.
Q Do not use a brush or blower brush. Failure to observe this precaution could damage the sensor.
2 Check whether the dust has been successfully removed.
R Repeat Steps 1 and 2 as necessary.
3 Replace the body cap or lens.
150
Troubleshooting
Problems and Solutions
■ Power and Battery
Problem
The camera does not
turn on.
The monitor does not
turn on.
The battery runs down
quickly.
The battery is exhausted
exhausted:: Charge the battery ((P
P 19) or insert a fully-charged spare battery ((P
P 20).
Reinsert the battery in the correct orientation and make sure that the charger is plugged in ((P
P 19).
Charge the battery at room temperature ((P
P v).
• There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
• The battery has been charged many times
times:: The battery has reached the end of its charging life. Purchase a new
battery. If the battery still fails to charge, contact your FUJIFILM dealer.
■ Menus and Displays
Problem
Display is not in English.
Solution
Select ENGLISH for D USER SETTING >
SETTING > a ((P
P 27, 115).
Troubleshooting
The camera turns off
suddenly.
Charging does not start.
Charging is slow.
The charging lamp blinks,
but the battery does not
charge.
Solution
• The battery is exhausted
exhausted:: Charge the battery ((P
P 19) or insert a fully-charged spare battery ((P
P 20).
• The battery is inserted incorrectly:
incorrectly: Reinsert in the correct orientation ((P
P 20).
• The battery-chamber cover is not latched
latched:: Latch the battery-chamber cover ((P
P 20).
The monitor may not turn on if the camera is turned off and then on again very quickly. Press the shutter button
halfway to activate the monitor.
• The battery is cold
cold:: Warm the battery by placing it in a pocket or other warm place and reinsert it in the camera
immediately before taking a picture.
• There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
• ON is selected for G AF/MF SETTING > PRE-AF
PRE-AF:: Turn PRE-AF off (P
(P 95).
• The battery has been charged many times
times:: The battery has reached the end of its charging life. Purchase a new
battery.
151
Problems and Solutions
■ Shooting
Problem
No picture is taken when
the shutter button is
pressed.
Mottling (“noise”) appears
in the monitor or viewfinder when the shutter
button is pressed halfway.
The camera does not focus.
Intelligent Face Detection
is not available.
•
•
•
•
•
•
Solution
The memory card is full
full:: Insert a new memory card or delete pictures (P
(P 22, 43).
The memory card is not formatted
formatted:: Format the memory card (P
(P 114).
There is dirt on the memory card contacts
contacts:: Clean the contacts with a soft, dry cloth.
The memory card is damaged
damaged:: Insert a new memory card ((P
P 22).
The battery is exhausted
exhausted:: Charge the battery ((P
P 19) or insert a fully-charged spare battery ((P
P 20).
The camera has turned off automatically:
automatically: Turn the camera on (P
(P 25).
Gain is increased to aid composition when the subject is poorly lit and aperture is stopped down, which may result
in noticeable mottling when images are previewed in the displays. Images taken with the camera are unaffected.
The subject is not suited to autofocus
autofocus:: Use focus lock ((P
P 77) or manual focus (P
(P 64).
Intelligent Face Detection is not available in the current shooting mode
mode:: Choose a different shooting mode ((P
P 167).
• The subject’s face is obscured by sunglasses, a hat, long hair, or other objects
objects:: Remove the obstructions.
• The subject’s face occupies only a small area of the frame
frame:: Change the composition so that the subject’s face occupies a larger area of the frame ((P
P 95).
No face is detected.
• The subject’s head is tilted or horizontal
horizontal:: Ask the subject to hold their head straight.
• The camera is tilted
tilted:: Keep the camera level.
• The subject’s face is poorly lit
lit:: Shoot in bright light.
The selected subject is closer to the center of the frame than the main subject. Recompose the picture or turn face
Wrong subject is selected.
detection off and frame the picture using focus lock (P
(P 77).
152
Problems and Solutions
Problem
The flash does not fire.
The flash does not fully
light the subject.
Pictures are blurred.
Pictures are mottled.
Solution
The battery is exhausted
exhausted:: Charge the battery ((P
P 19) or insert a fully-charged spare battery ((P
P 20).
• The subject is not in range of the flash
ash:: Position the subject in range of the flash.
• The flash window is obstructed
obstructed:: Hold the camera correctly.
• Shutter speed is faster than 1/250 ss:: Choose a slower shutter speed ((P
P 36, 38, 80).
• The lens is dirty
dirty:: Clean the lens ((P
P xi).
• The lens is blocked
blocked:: Keep objects away from the lens.
• s is displayed during shooting and the focus frame is displayed in red:
red: Check focus before shooting ((P
P 76).
• Shutter speed is slow and the ambient temperature is high:
high: This is normal and does not indicate a malfunction.
• Pixel mapping is required:
required: Perform pixel mapping using H IMAGE QUALITY SETTING >
SETTING > PIXEL MAPPING
(P 92).
• The camera has been used continuously at high temperatures or a temperature warning is displayed
displayed:: Turn the camera off and wait for it to cool down.
Troubleshooting
153
Problems and Solutions
■ Playback
Problem
Pictures are grainy.
Playback zoom is
unavailable.
No sound in movie
playback.
Selected pictures are not
deleted.
File numbering is
unexpectedly reset.
Solution
The pictures were taken with a different make or model of camera.
The pictures were created using RESIZE or with a different make or model of camera.
• Playback volume is too low:
low: Adjust playback volume (P
(P 46, 116).
• The microphone was obstructed
obstructed:: Hold the camera correctly during recording ((P
P 2, 44).
• The speaker is obstructed
obstructed:: Hold the camera correctly during playback ((P
P 2, 46).
Some of the pictures selected for deletion are protected. Remove protection using the device with which it was
originally applied (P
(P 108).
The battery-chamber cover was opened while the camera was on. Turn the camera off before opening the battery-chamber cover ((P
P 20, 25).
■ Connections/Miscellaneous
For additional information on troubleshooting wireless connections, visit:
http://digital-cameras.support.fujifilm.com/app?pid=x
Problem
Problem connecting or
uploading pictures to
smartphone.
Can not upload images.
154
Solution
• The smartphone is too far away:
away: Move the devices closer.
• Nearby devices are causing radio interference
interference:: Move the camera and smartphone away from microwave ovens or
cordless phones.
• The smartphone is connected to another device
device:: The smartphone and camera can connect to only one device at a
time. End the connection and try again.
• There are several smartphones in the vicinity
vicinity:: Try connecting again. The presence of multiple smartphones can
make connection difficult.
• The current image is a movie or was created on another device and can not be uploaded to a smartphone.
Problems and Solutions
Problem
Solution
Select ON for D CONNECTION SETTING > WIRELESS SETTING
SETTING >
> RESIZE IMAGE FOR SMARTPHONE
Smartphone will not
H. Selecting OFF increases upload times for larger images; in addition, some phones may not display images
display pictures.
over a certain size.
• The camera is not properly connected:
connected: Connect the camera properly (P
(P 137).). Note that once the camera is connected, pictures will be displayed on the TV instead of in the camera monitor.
No picture or sound on TV.
• Input on the television is set to “TV”:
“TV”: Set input to “HDMI”.
• The volume on the TV is too low:
low: Use the controls on the television to adjust the volume.
The computer does not
Be sure the camera and computer are correctly connected ((P
P 131).).
recognize the camera.
Can not transfer RAW or
Use MyFinePix Studio to transfer pictures (Windows only; P 130).).
JPEG files to computer.
• Temporary camera malfunction:
malfunction: Remove and reinsert the battery ((P
P 20).
The camera is
• The battery is exhausted
exhausted:: Charge the battery ((P
P 19) or insert a fully-charged spare battery ((P
P 20).
unresponsive.
• The camera is connected to a wireless LAN
LAN:: End the connection.
The camera does not funcRemove and reinsert the battery ((P
P 20). If the problem persists, contact your FUJIFILM dealer.
tion as expected.
No sound.
Adjust the volume (P
(P 116).
Troubleshooting
155
Warning Messages and Displays
The following warnings appear in the display.
Warning
i (red)
j (blinks red)
s
(displayed in red with
red focus frame)
Aperture or shutter speed
displayed in red
FOCUS ERROR
TURN OFF THE CAMERA
AND TURN ON AGAIN
LENS CONTROL ERROR
LENS ERROR
BUSY
CARD NOT INITIALIZED
PROTECTED CARD
156
Description
Low battery. Charge the battery ((P
P 19) or insert a fully-charged spare battery ((P
P 20).
Battery exhausted. Charge the battery ((P
P 19) or insert a fully-charged spare battery ((P
P 20).
The camera can not focus. Use focus lock to focus on another subject at the same distance, then recompose the
picture (P
(P 77).
The subject is too bright or too dark and the picture will be over- or under-exposed. Use the flash for additional
lighting when taking photographs of poorly-lit subjects (P
(P 79).
Camera malfunction. Turn the camera off and then on again. If the message persists, contact a FUJIFILM dealer.
Turn the camera off, remove the lens, and clean the mounting surfaces, then replace the lens and turn the camera
on. If the problem persists, contact a FUJIFILM dealer.
The memory card is incorrectly formatted. Use the camera to format the card ((P
P 114).
• The memory card is not formatted or the memory card has been formatted in a computer or other device
device:: Format the
memory card using D USER SETTING >
SETTING > FORMAT ((P
P 114).
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If the message is repeated,
format the card (P
(P 114). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
The memory card is locked. Unlock the card.
Warning Messages and Display
Warning
CARD ERROR
b MEMORY FULL
NO CARD
WRITE ERROR
READ ERROR
Troubleshooting
FRAME NO. FULL
Description
• The memory card is not formatted for use in the camera
camera:: Format the card (P
(P 114).
• The memory card contacts require cleaning or the memory card is damaged
damaged:: Clean the contacts with a soft, dry
cloth. If the message is repeated, format the card (P
(P 114). If the message persists, replace the card.
• Incompatible memory card:
card: Use a compatible card ((P
P 24).
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
The memory card is full and pictures can not be recorded. Delete pictures (P
(P 43) or insert a memory card with
more free space ((P
P 22).
The shutter can only be released when a memory card is inserted. Insert a memory card.
• Memory card error or connection error:
error: Reinsert the card or turn the camera off and then on again. If the message
persists, contact a FUJIFILM dealer.
• Not enough memory remaining to record additional pictures
pictures:: Delete pictures (P
(P 43) or insert a memory card with
more free space ((P
P 22).
• The memory card is not formatted
formatted:: Format the memory card (P
(P 114).
• The file is corrupt or was not created with the camera
camera:: The file can not be viewed.
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If the message is repeated,
format the card (P
(P 114). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
The camera has run out of frame numbers (current frame number is 999-9999). Format the memory card and select RENEW for D SAVE DATA SETTING
SETTING >
>FRAME
FRAME NO.
NO... Take a picture to reset frame numbering to 100-0001,
then select CONTINUOUS for FRAME NO.
NO...
157
Warning Messages and Display
Warning
PROTECTED FRAME
CAN NOT CROP
m CANNOT EXECUTE
F CANNOT EXECUTE
CAN NOT ROTATE
F CAN NOT ROTATE
DPOF FILE ERROR
CAN NOT SET DPOF
F CAN NOT SET DPOF
p (yellow)
p (red)
158
Description
An attempt was made to delete or rotate to a protected picture. Remove protection and try again ((P
P 108).
The picture is damaged or was not created with the camera.
Red-eye removal can not be applied to pictures created with other devices.
Red-eye removal can not be applied to movies.
The selected picture can not be rotated.
Movies can not be rotated.
The DPOF print order on the current memory card contains more than 999 images. Copy the pictures to a computer and create a new print order.
The picture can not be printed using DPOF.
Movies can not be printed using DPOF.
Turn the camera off and wait for it to cool. Mottling may increase in pictures taken when this warning is displayed.
Turn the camera off and wait for it to cool. Display quality and burst rate will drop, and mottling may increase in
pictures taken when this warning is displayed.
Appendix
Memory Card Capacity
The following table shows the recording time or number of pictures available at different image sizes.
All figures are approximate; file size varies with the scene recorded, producing wide variations in the
number of files that can be stored. The number of exposures or length remaining may not diminish
at an even rate.
8 GB
Capacity
O
T FINE
540
T FINE
1110
T NORMAL
1660
150
300
320
630
26 min.
54 min.
51 min.
105 min.
Appendix
O3:2
Photographs RAW (UNCOMPRESSED)
RAW (LOSSLESS COMPRESSED)
i 1080/60 P 2
i 1080/50 P 2
i 1080/30 P 2
i 1080/25 P 2
i 1080/24 P 2
Movies 1
h 720/60 P 3
h 720/50 P 3
h 720/30 P 3
h 720/25 P 3
h 720/24 P 3
1 Use a UHS speed class 1 card or better.
2 Individual movies can not exceed 14 minutes in length.
3 Individual movies can not exceed 28 minutes in length.
16 GB
T NORMAL
800
159
Links
For more information on FUJIFILM digital camera, visit the websites listed below.
FUJIFILM X-Pro2 Product Information
Optional accessories and support information can be found on the following website.
fujifilm X-Pro2
Firmware Updates
Updates to product firmware may result in changes not described in the manual. For more information, visit:
http://www.fujifilm.com/support/digital_cameras/software
fujifilm firmware
Checking the Firmware Version
Q The camera will only display the firmware version if a memory card is inserted.
1 Turn the camera off and check that a memory card is inserted.
2 Turn the camera on while pressing the DISP/BACK button. The current firmware version will be displayed; check the firmware version.
3 Turn the camera off.
160
Specifications
System
Model
Effective pixels
Image sensor
Storage media
Memory card slots
File system
File format
Image size
Lens mount
Sensitivity
Metering
Exposure control
Exposure compensation
Shutter speed
Appendix
FUJIFILM X-Pro2 digital camera
Approx. 24.3 million
23.5 mm × 15.6 mm (APS-C), X-Trans CMOS III sensor with primary color filter
FUJIFILM-recommended SD/SDHC/SDXC memory cards
Two SD memory card slot
Compliant with Design Rule for Camera File System (DCF)
(DCF),, Exif 2.3, and Digital Print Order Format (DPOF)
• Still pictures:
pictures: Exif 2.3 JPEG (compressed)
(compressed);; RAW (original RAF format, uncompressed or compressed using a lossless algorithm; special
purpose software required); RAW+JPEG available
• Movies
Movies:: H.264 standard with stereo sound (MOV)
• O 3 : 2:
2: 6,000 × 4,000
• O 16 : 9:
9: 6,000 × 3,376
• O 1 : 1:
1: 4,000 × 4,000
• P 3 : 2:
2: 4,240 × 2,832
• P 16 : 9:
9: 4,240× 2,384
• P 1 : 1:
1: 2,832 × 2,832
• Q 3 : 2:
2: 3,008 × 2,000
• Q 16 : 9:
9: 3,008 × 1,688
• Q 1 : 1:
1: 2,000 × 2,000
FUJIFILM X mount
Standard output sensitivity equivalent to ISO 200 – 12800; AUTO; extended output sensitivity equivalent to
ISO 100, 125, 160, 25600, or 51200
256-segment throughhrough-tthehe-llens (TTL) metering; MULTI, SPOT, AVERAGE, CENTER WEIGHTED
Programmed AE (with program shift)
shift);; shutter-priority AE; aperture-priority AE; manual exposure
–5 EV – +5 EV in increments of / EV
• MECHANICAL SHUTTER
- P mode
mode:: 4 sec. to / sec.
- Time
Time:: 15 min. to / sec.
- Bulb
Bulb:: Max. 60 min.
- All other modes:
modes: 15 min. to / sec.
• ELECTRONIC SHUTTER
- P, S, A, and M modes
modes:: 1 sec. to / sec.
- Time
Time:: 1 sec. to / sec.
- Bulb
Bulb:: Fixed at 1 sec.
• MECHANICAL + ELECTRONIC
- P mode
mode:: 4 sec. to / sec.
- Time
Time:: 15 min. to / sec.
- Bulb
Bulb:: Max. 60 min.
- All other modes:
modes: 15 min. to / sec.
161
Specifications
System
Continuous
Focus
White balance
Self-timer
Flash
Mode
Hot shoe
Sync terminal
Hybrid viewfinder
LCD monitor
162
Mode
8.0 fps
I
3.0 fps
Frame rate (fps)
8.0
3.0
Frames per burst
Up to approximately 53
Up to approximately 62
R The frame rate and number of frames per burst may vary depending on the type of memory card
used. The figures above are for UHS speed class 1 cards.
R The frame rate varies with shooting conditions and the number of images recorded.
• Mode
Mode:: Single or continuous AF; manual focus with focus ring
• Focus-area selection
selection:: SINGLE POINT, ZONE, WIDE/TRACKING
• Autofocus system:
system: Intelligent hybrid AF (TTL contrast-detect/phase-detection AF) with AF-assist illuminator
Custom 1, Custom 2, Custom 3, color temperature selection, auto, direct sunlight, shade, daylight fluorescent,
warm white fluorescent, cool white fluorescent, incandescent, underwater
Off, 2 sec., 10 sec.
Accessory shoe with TTL contacts and sync contact (X contact) that supports sync speeds as fast as /
/
 s
Auto, fill flash, off, slow sync, rear-curtain sync, commander (red-eye removal off );); auto with red-eye removal, fill flash
with red-eye removal, off, slow sync with red-eye removal, rear-curtain sync with red-eye removal, commander
(red-eye removal on)
Accessory shoe with TTL contacts
Provided
• Optical viewfinder (OVF):
(OVF): Reverse Galilean viewfinder with electronic bright frame display and approx. 0.36×/0.6×
magnification; frame coverage approx. 92%
• Electronic viewfinder (EVF)
(EVF):: 0.48-in., 2,360k-dot color LCD viewfinder with diopter adjustment (–4 to +2 m–1);
magnification 0.59× with 50 mm lens (35 mm format equivalent) at infinity and diopter set to –1.0 m–1; diagonal
angle of view approximately 29.1° (horizontal angle of view approximately 24.4°); eye point approx. 16 mm
Fixed 3.0-in/7.6 cm, 1620k-dot color LCD monitor
Specifications
System
Movies
•
•
•
•
•
•
•
•
•
•
i 1080/60P
1080/60P:: Frame size 1,920 × 1,080 (1080p); 60 fps; stereo sound
i 1080/50P
1080/50P:: Frame size 1,920 × 1,080 (1080p); 50 fps; stereo sound
i 1080/30P
1080/30P:: Frame size 1,920 × 1,080 (1080p); 30 fps; stereo sound
i 1080/25P
1080/25P:: Frame size 1,920 × 1,080 (1080p); 25 fps; stereo sound
i 1080/24P
1080/24P:: Frame size 1,920 × 1,080 (1080p); 24 fps; stereo sound
h 720/60P
720/60P:: Frame size 1,280 × 720 (720p); 60 fps; stereo sound
h 720/50P
720/50P:: Frame size 1,280 × 720 (720p); 50 fps; stereo sound
h 720/30P
720/30P:: Frame size 1,280 × 720 (720p); 30 fps; stereo sound
h 720/25P
720/25P:: Frame size 1,280 × 720 (720p); 25 fps; stereo sound
h 720/24P
720/24P:: Frame size 1,280 × 720 (720p); 24 fps; stereo sound
Input/output terminals
HDMI output
Micro HDMI connector (Type D)
Digital input/output
Micro USB connector (USB 2.0 High-Speed)
Microphone/
φ2.5 mm mini-stereo jack
remote release connector
EVF
210
250
330
OVF
350
350
380
CIPA standard, measured using battery supplied with camera and SD memory card.
Appendix
Power supply/other
Power supply
NP-W126/NP-W126S rechargeable battery
Battery life (approximate • Battery type
type:: NP-W126/NP-W126S (type supplied with camera)
number of frames that can
• Approximate number of frames
frames::
be taken with a fully-charged
LCD
battery in mode P, XF 35 mm HIGH PERFORMANCE
250
f/1.4 R lens)
STANDARD
280
ECONOMY
330
Note: Number of shots that can be taken with battery varies with battery charge level and will decline at low
Note:
temperatures.
163
Specifications
Power supply/other
Camera size (W × H × D)
Camera weight
Shooting weight
Operating conditions
Wireless transmitter
Standards
Operating frequency
Access protocols
164
140.5 mm × 82.8 mm × 45.9 mm (34.8
(34.8 mm excluding projections, measured at thinnest part)/5.5
part)/5.5 in. × 3.3 in. × 1.8 in. (1.4 in.)
Approx. 445 g/15.7 oz., excluding battery, accessories, and memory card
Approx. 495 g/17.5 oz., including battery and memory card
• Temperature
Temperature:: –10 °C to +40 °C/+32 °F to +104 °F
• Humidity
Humidity:: 10% – 80% (no condensation)
IEEE 802.11b/g/n (standard wireless protocol)
• U. S. A., Canada, Taiwan:
Taiwan: 2,412 MHz–2,462 MHz (11 channels)
• Other countries:
countries: 2,412 MHz–2,472 MHz (13 channels)
Infrastructure
Specifications
NP-W126/NP-W126S rechargeable battery
Nominal voltage
7.2 V DC
Nominal capacity
1,260 mAh
Operating temperature 0 °C to +40 °C/+32 °F to +104 °F
Dimensions (W × H × D) 36.4 mm × 47.1 mm × 15.7 mm/1.4 in. × 1.9 in. × 0.6 in.
Weight
Approx. 47 g/1.7 oz.
BC-W126 battery charger
Rated input
Input capacity
Rated output
Supported batteries
Charging time
Operating temperature
Dimensions (W × H × D)
Weight
100 V – 240 V AC, 50/60 Hz
13 –21 VA
8.4 V DC, 0.6 A
NP-W126/NP-W126S rechargeable batteries
Approx. 150 minutes (+20 °C/+68 °F)
5 °C to +40 °C/+41 °F to +104 °F
65 mm × 91.5 mm × 28 mm/2.6 in. × 3.6 in. × 1.1 in., excluding projections
Approx. 77 g/2.7 oz., excluding battery
Weight and dimensions vary with the country or region of sale. Labels, menus, and other displays may differ from those on the
actual camera.
Appendix
165
Specifications
■ Notices
• Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/
digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual.
• Although the viewfinder and LCD monitor are manufactured using advanced high-precision technology, small
bright points and anomalous colors may appear, particularly in the vicinity of text. This is normal for this type of
LCD display and does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electricity,
or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.
166
Restrictions on Camera Settings
The options available in each shooting mode are listed below. Some options may not be available for
the items that are supported in any given mode, and function may be restricted depending on shooting conditions.
P
S
A
M
R
BKT
j
Y
F
r8
F
S.S.
Program shift
Exposure compensation
✔1
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔4
✔
✔1
✔
✔4
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔5
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔3
✔
✔
✔3
✔3
✔
✔
✔
✔
✔3
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔3
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔7
✔
✔7
✔1
✔7
✔
✔
✔
✔
✔
✔
✔7
✔7
✔7
✔7
✔7
✔
✔
✔
✔
✔
✔
✔7
S
C
M
AUTO
H (51200) /H (25600)
12800 – 1000
800
640 – 200
L (100) /L (125) /L (160)
O
P
Q
FINE/NORMAL
RAW
c
d/e/i
g/h
a/d/c/b
b/e/d/f
f
Focus mode
Sensitivity
IMAGE SIZE
IMAGE QUALITY
FILM SIMULATION
GRAIN EFFECT
✔
✔2
✔
✔
✔
✔
✔
✔
✔9
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Appendix
Shooting mode/scene position
167
Restrictions on Camera Settings
Shooting mode/scene position
AUTO
V/W/X
DYNAMIC RANGE
WHITE BALANCE
HIGHLIGHT TONE
SHADOW TONE
COLOR
SHARPNESS
NOISE REDUCTION
LONG EXPOSURE NR
LENS MODULATION OPTIMIZER
COLOR SPACE
SELECT CUSTOM SETTING
EDIT/SAVE CUSTOM SETTING
r
y
z
AF MODE
AF ILLUMINATOR
FACE DETECTION
EYE DETECTION AF
AF+MF
STANDARD
DIGITAL SPLIT IMAGE
FOCUS PEAK HIGHLIGHT
MF ASSIST
FOCUS CHECK
SELF-TIMER
168
P
S
A
M
R
BKT
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
j
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
Y
F
r8
✔
✔
✔1
✔1
✔7
✔7
✔
✔7
✔7
✔7
✔7
✔7
✔7
✔7
✔7
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔6
✔1
✔1
✔7
✔
✔
Restrictions on Camera Settings
Shooting mode/scene position
o
p
PHOTOMETRY
v
w
t
SHUTTER TYPE
t+s
s
l
IS MODE
m
OFF
PREVIEW EXP./WB IN MANUAL MODE
P
S
A
M
R
BKT
j
Y
F
r8
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔1
✔7
✔
✔7
✔7
✔7
✔7
✔7
✔7
✔7
✔7
✔7
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
Appendix
169
Restrictions on Camera Settings
Shooting mode/scene position
DISP. CUSTOM SETTING
AF-LOCK MODE
170
1
2
3
4
5
FRAMING GUIDELINE
ELECTRONIC LEVEL
FOCUS FRAME
AF DISTANCE INDICATOR
MF DISTANCE INDICATOR
HISTOGRAM
SHOOTING MODE
APERTURE/S-SPEED/ISO
INFORMATION BACKGROUND
Expo. Comp. (Digit)
Expo. Comp. (Scale)
FOCUS MODE
PHOTOMETRY
SHUTTER TYPE
FLASH
CONTINUOUS MODE
DUAL IS MODE
WHITE BALANCE
FILM SIMULATION
DYNAMIC RANGE
FRAMES REMAINING
IMAGE SIZE/QUALITY
MOVIE MODE & REC. TIME
BATTERY LEVEL
AF-L
AE+AF
Fixed automatically.
Restricted to range of ±2.0 EV during movie recording.
Options available vary with shooting mode.
A is not available.
Available only with auto ISO sensitivity.
P
S
A
M
R
BKT
j
Y
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
6
7
8
9
F
r8
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
sRGB selected automatically.
Still photography settings are used.
Wireless remote photography.
Maximum sensitivity for movies is ISO 6400.
✔
✔
✔
✔
✔
✔7
✔7
Memo
171
Memo
172
Memo
173
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising