D5/6 Series Doors
1.
2. 7
3.
4.
D5/6 Series Doors
Installation Manual
RollSeal
1733 County Road 68
Bremen, Alabama 35033
256-287-7000
Part No 4801-5154 Rev 09-2014
Owners Manual
D5/6 Doors
Table of Contents
Use of Equipment .......................................................................................................................................................... 1 1 Physical Description ............................................................................................................................................... 1 Operator Options ........................................................................................................................................................... 2 2 Differences between a D5 and D6 Series Door ...................................................................................................... 2 3 Ratings and Specifications D5 Series (Brother Motor) .......................................................................................... 3 4 Ratings and Specifications D6 Series (Brother Motor) .......................................................................................... 4 5 Ratings and Specifications D5/6 Series (Manaras Motor) ...................................................................................... 5 Error! Bookmark not defined. 6 Ratings and Specifications D5 Series (Freezer Kit) ............................................................................................... 5 7 Ratings and Specifications D6 Series (Freezer Kit) ............................................................................................... 7 Warnings (Avertissements) ........................................................................................................................................... 8 Limited Warranty ........................................................................................................................................................ 13 8 Installation of D5/6 Series Doors ......................................................................................................................... 14 8.1 Tools Required ............................................................................................................................................. 14 8.2 Overview...................................................................................................................................................... 14 8.3 Adjusting the Door Framing or Clear Opening............................................................................................ 14 8.4 Attachment Points of Door .......................................................................................................................... 15 8.5 Assembly of Parts ........................................................................................................................................ 16 8.6 Infrared Sensor Connectors (Brother Motor Option Only) .......................................................................... 17 8.7 Fastening Door Assembly to Clear Opening ............................................................................................... 17 9 Mounting Operators to D5/6 Series Doors ........................................................................................................... 19 10 Mounting Brother Operator to D5/6 Series Door ................................................................................................. 21 11 Installation of D5/6 Series Doors (Freezer Kit Included) ..................................................................................... 22 11.1 Tools Required ............................................................................................................................................. 22 11.2 Overview...................................................................................................................................................... 22 12 Installation of Condensation Management System and Ducts ............................................................................. 23 12.1 Connecting the Electrical Power .................................................................................................................. 23 13 Mounting Manual Chain Hoist to D5/6 Series Door ............................................................................................ 24 13.1 First Safety Bracket ..................................................................................................................................... 24 13.2 Removal of Second Safety Bracket ............................................................................................................. 24 13.3 Chain Hoist Installation ............................................................................................................................... 25 14 Connecting Electrical Power to D5/6 Series Doors .............................................................................................. 26 15 Operation of D5/6 Series Doors ........................................................................................................................... 26 Page i
Table of Contents
Part No 4801-5154 Rev 09-2014
15.1 Limit Switches ............................................................................................................................................. 27 16 D5/6 Series Door Wiring Diagram (Brother Motor Only) ................................................................................... 28 17 RollSeal Smart Controller Wiring Diagram (Brother Motor Only) ..................................................................... 29 18 Operation of D5/6 Series Door with Freezer Kit Included ................................................................................... 30 18.1 SC-325 or SC-650 Program Setup for Freezer Mode .................................................................................. 30 18.2 Open and Close Door ................................................................................................................................... 32 19 D5/6 Series Door Condensation Management System Wiring Diagram .............................................................. 33 20 Manual Operation D5/6 Series Door (Brother Motor Only) ................................................................................ 34 20.1 Operating Instructions.................................................................................................................................. 34 21 Adjustment of Brake (Brother Motor Only) ......................................................................................................... 35 22 Operation of D5/6 Series with Manaras Motor Option. ....................................................................................... 36 22.1 Limit Switches. ............................................................................................................................................ 36 22.2 Adjustment of Limit Switches ..................................................................................................................... 37 22.3 Wiring Options to the Manaras Operator Terminal Block ........................................................................... 38 22.3 Switch Operation of Door with Manaras Operator ...................................................................................... 39 23 Manual Operation Manaras Operator ................................................................................................................... 39 24 Operation of D5/6 Series with Manual Chain Hoist Option ................................................................................. 40 25 Emergency Egress ................................................................................................................................................ 41 25.1 Installation ................................................................................................................................................... 41 25.2 Exiting (Opening) The Door ........................................................................................................................ 41 25.3 Resetting (Closing) The Door ...................................................................................................................... 42 26 Egress Strap Removal/Re-Installation .................................................................................................................. 43 26.1 Removal ....................................................................................................................................................... 43 26.2 Installation ................................................................................................................................................... 43 27 Door Panel Adjustments ....................................................................................................................................... 44 28 Removal of Existing Panel ................................................................................................................................... 45 29 Installation of Replacement Panel ........................................................................................................................ 45 30 Removing and Replacing Floating Magnets or Velcro ........................................................................................ 47 31 D5/6 Door Options and Accessories .................................................................................................................... 52 Part No 4801-5154 Rev 09-2014
Table of Contents
Page ii
Use of Equipment
The D5/6 Series Doors are motorized curtain enclosures for environmental control, banana rooms,
docks/warehouses, car and truck washes, agricultural/horticultural, and coolers/freezers.
1 Physical Description
The D5/6 Series Doors are available with multiple features and options such as:

Standard Door Sizes: Refer to Tables 1-4, D5/6 Series Standard Dimensions, pages 3, 4, 5, and 7.

Operators: Manual Chain Hoist, Brother or Manaras Operator.

Left/Right/Front Mounting: The Manaras Operators can be mounted on the left, right or front. The
manual chain hoist can be mounted on the left or right side.

The Operator Mounting Side must be selected at the time of order.

Left Mounting Only: The Brother motor can only be mounted on the left side, the associated controller, on
the right side.

Manaras Operator Voltage Selection: 1/2 HP, Single Phase: 115V @ 8.6 amp, 230V @ 4.1 amp. 1/2 HP,
3 Phase: 208V @ 2.2 amp, 460V @ 1.1 amp. 1 HP, Single Phase: 115V @ 13.4 amp, 230V @ 6.7 amp. 1
HP, 3 Phase: 208V @ 3.4 amp, 460V @ 1.7 amp.

D5 with Brother Motor - Controller Standard Input Voltage 115VAC (Must request 230VAC).

D6 with Brother Motor - Controller Standard Input Voltage 230VAC.

Operator Options: Remote receiver and transmitters, photo safety beams, leading edge switch.

Accessories: Industry standard accessories can be added such as motion sensors, loop detectors, ceiling
pull switches, lock-out switches, other various types of switches, and door status / movement indicators
such as lights and buzzers.

Windows: 32" high with width varying by width of door panel.

Fabric & Fabric Colors: Frost, white, black, blue, red, tan, green, anti-static, and insect screen.
NOTE: Certain options may only be available with specific operators. Refer to Section 31,
D5/6 Door Options and Accessories.
Page 1
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
Operator Options
Manual Drive
Left/Right
Option
Brother (Left Side
Mount Only)
Manaras
(Left, Right,
Wall, or Front
Mount Only)
2 Differences between a D5 and D6 Series Door
Speed (Brother Motor Option)
Speed (Manaras Motor)
Motor (Brother)
Motor (Manaras)
Drive Pipe
Head Unit
*Standard Controller Input Voltage
(Brother Motor Option)
D5 Series
Up to 18” Per Sec
@8-11” Per Sec
1/4hp
1/2hp GH
2 ½ inches
Small
115VAC
D6 Series
Up to 48” Per Sec
@16-22” Per Sec
1/2hp
1hp GH
6 inches
Large
230VAC
*NOTE: When Brother Motor Option is used you can request that a D5 Door
be wired for 115VAC or 230VAC. The D6 is wired for 230 VAC only.
This must be done prior to purchase to ensure the door has the
correct brake rectifier installed.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 2
3
Ratings and Specifications D5 Series (Brother Motor)
D5 Series Motor Rating………..230 VAC, Three Phase, 1/4 hp Motors will be connected through controller.
See RS SC-325 or SC-650 Manual (4801-5156).
E
14 1/8 in (35.88 cm)
6 in (15.24 cm)
15 in
(38.03 cm)
Space for
access
door
removal
B
C
A
D
WIDTH Related Dimensions
A
5 1/8 in
(12.93 cm)
TABLE 1 D5 Door Standard Dimensions:
HEIGHT Related Dimensions
D
RS500
Door
Height
In.
cm
In.
cm
206
7'(H)
84
214
104-11/16
266
236
7'6"(H)
90
229
110-11/16
281
96
244
116-11/16
296
E
RS500
Door
Width
In.
cm
In.
cm
In.
cm
4'(W)
48
122
64-13/32
164
80-15/16
5'(W)
60
153
76-13/32
194
92-15/16
B
C
6'(W)
72
183
88-13/32
225
104-15/16
267
8'(H)
6'6"(W)
78
198
94-13/23
240
110-15/16
282
9'(H)
108
275
128-11/16
327
7'(W)
84
214
100-13/32
255
116-15/16
297
10'(H)
120
305
140-11/16
357
132
335
152-11/16
387
144
366
164-11/16
418
8'(W)
96
244
112-13/32
286
128-15/16
328
11'(H)
10'(W)
120
305
136-13/32
347
152-15/16
388
12'(H)
11'(W)
132
335
148-13/32
377
164-15/16
419
144
366
160-13/32
408
176-15/16
449
12'(W)
Page 3
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
4
Ratings and Specifications D6 Series (Brother Motor)
Motor Rating………..230 VAC, Three Phase, 1/2 hp
Motor must be connected through controller. See RS SC-650 Manual (4801-5156).
E
14 1/8 in (35.88 cm)
6 in (15.24 cm)
15 in
(38.03 cm)
Space for
access
door
removal
B
C
A
D
WIDTH Related Dimensions
A
5 1/8 in
(12.93 cm)
TABLE 2 D6 Door Standard Dimensions:
HEIGHT Related Dimensions
cm
RS600
Door
Height
In.
cm
In.
cm
80-15/16
206
7'(H)
84
214
92-11/16
266
194
92-15/16
236
8'(H)
96
244
104-11/16
296
D
E
RS600
Door
Width
In.
cm
In.
cm
In.
4'(W)
48
122
64-13/32
164
5'(W)
60
153
76-13/32
6'(W)
B
C
72
183
88-13/32
225
104-15/16
267
9'(H)
108
275
128-11/16
327
7'(W)
84
214
100-13/32
255
116-15/16
297
10'(H)
120
305
140-11/16
357
8'(W)
96
244
112-13/32
286
128-15/16
328
9'(W)
108
274
124-13/32
316
140-15/16
358
10'(W)
120
305
136-13/32
347
152-15/16
388
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 4
5
Ratings and Specifications D5/6 Series (Manaras Motor)
D5 Series Motor Rating 1/2 HP
115V Single Phase 8.6 amp
230V Single Phase 4.1 amp
208V 3 Phase 3.4 amp
460V 3 Phase 1.7 amp
D6 Series Motor Rating 1 HP
115V Single Phase 13.4 amp
230V Single Phase 6.7 amp
208V 3 Phase 3.4 amp
460V 3 Phase 1.7 amp
Motor must be mounted and wired utilizing instructions in this manual and the MANARAS installation and
Instruction Manual.
3
4
5
6
1
2
POSITION 1, 4 and 5 – GH motor mounted on left side.
POSITION 2, 3 and 6 – GH Motor mounted right side.
Page 5
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
Ratings and Specifications D5 Series (Freezer Kit)
DOOR MOTOR:
CONDENSATION MANAGEMENT
SYSTEM (CMS):
• 230 VAC Three Phase, ¼ hp
• Voltage Rating 230 VAC ± 10% 50/60 Hz
• Blower 135 Watt
• Heater 1200 Watt
• Total Current:5.8 A @ 230 VAC (Typical)
•
9.0 A @ 230 VAC (Max.)
E
6 in
(15.24 cm)
14 1/8 in
(35.88 cm)
17 3/8 in
(44.05 cm)
Space for
access
door
removal
B
C
A
14 3/4 in
(37.50 cm)
5 3/4 in
(14.61 cm)
D
TABLE 3 D5 Door Standard Dimensions:
WIDTH Related Dimensions
HEIGHT Related Dimensions
A
D
E
cm
RS500
Door
Height
In.
cm
In.
cm
80-15/16
206
7'(H)
84
214
104-11/16
266
227
92-15/16
236
7'6"(H)
90
229
110-11/16
281
258
104-15/16
267
8'(H)
96
244
116-11/16
296
RS500
Door
Width
In.
cm
In.
cm
In.
4'(W)
48
122
77-1/2
197
5'(W)
60
153
89-1/2
6'(W)
72
183
101-1/2
B
C
6'6"(W)
78
198
107-1/2
273
110-15/16
282
9'(H)
108
275
128-11/16
327
7'(W)
84
214
113-1/2
288
116-15/16
297
10'(H)
120
305
140-11/16
357
8'(W)
96
244
125-1/2
319
128-15/16
328
11'(H)
132
335
152-11/16
387
10'(W)
120
305
149-1/2
380
152-15/16
388
12'(H)
144
366
164-11/16
418
11'(W)
132
335
161-1/2
410
164-15/16
419
12'(W)
144
366
173-1/2
441
176-15/16
449
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 6
6
Ratings and Specifications D6 Series (Freezer Kit)
DOOR MOTOR:
CONDENSATION MANAGEMENT SYSTEM
(CMS):
• 230 VAC Three Phase, 1/2 hp
• Voltage Rating 230 VAC ± 10% 50/60 Hz
• Blower 135 Watt
• Heater 1200 Watt
• Total Current:5.8 A @ 230 VAC (Typical)
•
9.0 A @ 230 VAC (Max.)
E
6 in
(15.24 cm)
14 1/8 in
(35.88 cm)
17 3/8 in
(44.05 cm)
Space for
access
door
removal
B
C
A
14 3/4 in
(37.50 cm)
5 3/4 in
(14.61 cm)
D
WIDTH Related Dimensions
A
TABLE 4 D5 Door Standard Dimensions:
HEIGHT Related Dimensions
D
RS500
Door
Height
In.
cm
In.
cm
206
7'(H)
84
214
104-11/16
266
236
7'6"(H)
90
229
110-11/16
281
96
244
116-11/16
296
E
RS500
Door
Width
In.
cm
In.
cm
In.
cm
4'(W)
48
122
77-1/2
197
80-15/16
5'(W)
60
153
89-1/2
227
92-15/16
B
C
6'(W)
72
183
101-1/2
258
104-15/16
267
8'(H)
6'6"(W)
78
198
107-1/2
273
110-15/16
282
9'(H)
108
275
128-11/16
327
7'(W)
84
214
113-1/2
288
116-15/16
297
10'(H)
120
305
140-11/16
357
8'(W)
96
244
125-1/2
319
128-15/16
328
11'(H)
132
335
152-11/16
387
12'(H)
144
366
164-11/16
418
10'(W)
120
305
149-1/2
380
152-15/16
388
11'(W)
132
335
161-1/2
410
164-15/16
419
12'(W)
144
366
173-1/2
441
176-15/16
449
Page 7
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
Warnings (Avertissements)
! Warning!
Disconnect All Power Sources Before Installing This Equipment. Failure To Disconnect
Power Source Can Result In Property Damage, Serious Injury Or Death!
!! Warning!
Dangerous Rotating Machinery!
Keep Hands, Clothing, Etc. Clear When Operating!
Do Not Operate Without All Guards And Covers In Place!
! Warning!
All Wiring Should Be In Accordance with National Electrical Codes Or Other Local Codes.
!! Warning!
The Installer Is Responsible For Complying With All Relevant Regulations,
Such As National Wiring Regulations And Accident Prevention Regulations.
Particular Attention Must Be Given To The Cross-sectional Areas Of Conductors, The
Selection Of Fuses Or Other Protection, And Protective Earth/Ground Connections!
!! Warning!
The Voltages In The Power Cables And Certain Parts Of The Drive Can Result In Death.
Whenever The Drive Has Been Used, It Must Be Isolated And Disconnected
For 5 Minutes Before Any Work Commences.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 8
! Danger!
Only Qualified Electrical Personnel Familiar With The Construction And Operation Of This
Equipment And The Hazards Involved Should Install, Adjust, And/Or Service This Equipment.
Read And Understand This Manual In Its Entirety Before Proceeding.
Failure To Observe This Precaution Could Result In Severe Bodily Injury Or Death!
! Warning!
Item 4501-6312
(Warning Moving Door Label)
Supplied With Door,
MUST Be Installed
On Inside Of Cooler/Freezer
Beside Door Opening.
IMPORTANT INSTALLATION INSTRUCTIONS
!! Warning!
To Reduce The Risk Of Severe Injury Or Death:
1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.
2. Do not connect the door operator to the source of power until instructed to do so.
3. Locate the control station: (a) within sight of the door, (b) at a minimum height of 5 feet
so small children cannot reach it, and (c) away from all moving parts of the door.
Remove all ropes and remove or make inoperative all locks connected to the garage
door before installing opener.
4. For products having a manual release, instruct the end user on the operation of the
manual release. Where possible, install the door opener 7 feet or more above the floor.
For products having an emergency release, mount the emergency release within reach,
but at least 6 feet above the floor and avoiding contact with vehicles to avoid accidental
release.
Page 9
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
IMPORTANT SAFETY INSTRUCTIONS
!! Warning!
To Reduce The Risk Of Severe Injury Or Death:
1.
2.
READ AND FOLLOW ALL INSTRUCTIONS!
Never let children operate or play with door controls. Keep the remote control (where provided) away
from children.
3. Personnel should keep away from a door in motion and keep the moving door in sight until it is
completely closed or opened. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR.
4. Test the door’s safety features at least once a month. After adjusting either the speed or the limit of
travel, retest the door operator’s safety features. Failure to adjust the operator properly may cause
severe injury or death. NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.
5. For products having a manual release, if possible, use the manual release only when the door is
closed. Use caution when using this release when the door is open.
6. KEEP DOORS PROPERLY OPERATING AND BALANCED. See Door Manufacturer’s Owner’s
Manual. An improperly operating or balanced door can cause severe injury or death. Have trained
door systems technician make repairs to cables, spring assemblies, and other hardware.
7. Install the Entrapment Warning label next to the control button in a prominent location. Install the
Emergency Release Marking. Attach the marking on or next to the emergency release.
8. After installing the opener, the door must reverse when it contacts a 1-1/2 inch high object (or a 2 x 4
board laid flat) on the floor.
9. SAVE THESE INSTRUCTIONS.
French Translated Warnings
! Avertissement!
Disjoindre fournissent de l'énergie tout les sources avant qu'installer cet équipement.
F|ailure| à disjoindre la source de pouvoir peut résulter dans dommage de propriété,
blessure sérieuse ou mort !
! ! Avertissement !
Mécanisme tournant dangereux !
Garder les mains, vêtissant, etcC|lear| quand fonctionner !
Ne fonctionnez pas sans toutes gardes et couvertures dans lieu !
!
Avertissement !
Tout montage sur fil de fer doit être selon codes électriques nationaux ou autres
indicatifs régionaux.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 10
! ! Avertissement !
L'Installer est responsable pour conformer avec tout règlement pertinent, telles que
règlement et règlement de prévention d'accident de montage sur fil de fer nationaux.
Pl'attention articulaire doit être donnée pour les aires sectionnelles transversales de
conducteurs, le choix d'elles fusées ou autre protection, et terre / prises de terre
protecteur !
!
Avertissement !
Les tensions dans le pouvoir câblent et certains parties de la promenade en voiture
peuvent résulter dans la mort. Wle |henever| la promenade en voiture a été utilisé il
doit être isolé et détaché pendant 5 procès avant que tout travail commence.
!
Danger !
Seulement familier électrique de personnel qualifié avec la construction et opération
de cet équipement et les hasards ont enveloppé devoir installer, arranger, et/ou - la
révision cet équipement. R|ead| et comprendre ce manuel en entier avant que
procéder. F|ailure| à observer cette précaution peut résulter dans dommage corporel
sévère ou mort !
!
Avertissement !
Point 4501-6312
(Avertissement Moving étiquette de porte)
Livré avec porte,
doit être installé à
l'intérieur du réfrigérateur / congélateur
côté Ouverture de la porte.
Page 11
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
LES INSTRUCTIONS D'INSTALLATION
IMPORTANTES
! AVERTISSEMENT!
À réduire le risque de blessure sévère ou mort:
1. LU ET SUIVENT TOUTES INSTRUCTIONS D'INSTALLATION.
2. Ne liez pas l'opérateur de porte per la source de pouvoir jusqu'à instruit faire ainsi.
3. Localisez la station de commande: (a) en vue de la porte, (b) à un minimum la hauteur de 5
pieds ainsi petit enfants ne peuvent pas l'atteindre, et (c) loin de tous parties en mouvement
de la porte.
4.
Pour produits ayant un délivrance manuelle, instruire l'utilisateur final sur l'opération de la
délivrance manuelle.
RÈGLEMENTS DE SÉCURITÉ IMPORTANTS
! AVERTISSEMENT!
À réduire le risque de blessure sévère ou mort:
1. LU ET SUIVENT TOUTES INSTRUCTIONS!
2. Jamais laisser fonctionner enfants ou mouvoir vivement avec les autorités de porte. Gardez la
télécommande (où a fourni) loin des enfants.
3. Le personnel devrait garder loin une porte dans mouvement et subsistance la porte en
mouvement dans vue jusqu'à est complètement fermé ou avoir ouvert. CES AUCUNS DOIVENT
CROISER LE CHEMIN D'UNE PORTE EN MOUVEMENT.
4. Éprouvez les traits de sécurité de la porte au moins une fois par mois. Après qu'arrangeant la
vitesse ou la fin de course, retest les traits de sécurité de l'opérateur de porte. Manque à
arranger l'opérateur correctement peut causer blessure sévère ou mort.
5. Pour produits ai manuel la délivrance, si possible, utiliser la délivrance manuelle seulement quand
la porte est fermée. Précaution d'utilisation à utiliser cette délivrance quand la porte est ouverte.
6. GARDER LES PORTES CORRECTEMENT QUI OPÈRE ET ÉQUILIBRÉ. Voir la porte fabricant
propriétaire manuel. Un improprement qui opère ou balancé porte peut causer blessure sévère
ou mort. Formez les technicien de systèmes de porte faitez les réparations per les câbles,
réunions de source, et autre quincaillerie.
7.
SAUVEZ CES INSTRUCTIONS.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 12
Limited Warranty
All products are warranted to be free from defects in material and workmanship for a period of one
(1) year or 100,000 cycles, whichever occurs first, from the date of purchase if installed and used
in strict accordance with the installation instructions. Liability is limited to the sale price of any
products proved to be defective or, at manufacturers’ option, to the replacement of such products
upon their return. No products are to be returned to the manufacturer, until there is an inspection
and/or a return-goods authorization (RGA) number is issued.
All complaints should be directed first to the authorized distributor who sold the product. If
satisfaction is not obtained or the name of the distributor is not known, write the manufacturer that
appears below, directed to the attention of Customer Service Manager.
This limited warranty is expressly in lieu of any and all representations and warranties expressed
or implied, including any implied warranty of merchantability or fitness for a particular purpose.
The remedy set forth in this limited warranty shall be the exclusive remedy available to any person.
No person has authority to bind the manufacturer to any representation or warranty other than this
limited warranty. The manufacturer shall not be liable for any consequential damages resulting
from the use of our products or caused by any defect, failure or malfunction of our products. (Some
areas do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.)
This warranty gives you specific legal rights and you may also have other rights that vary from area
to area.
Warrantor:
RollSeal
1733 County Road 68
Bremen, Al 35055
256-287-7000
Page 13
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
7
Installation of D5/6 Series Doors
7.1 Tools Required
3/8 in. (10 mm) Power screwdriver (portable)
3/16 in. (5 mm) Drill bit and power drill
3/8 x 1 in. Bolts and nuts (supplied)
Socket
Hammer
Tape measure
Carpenter's level
NOTE: Other Tools May Be Required According To Installation.
7.2 Overview
The D5/6 Series doors are shipped with pre-assembled vertical members (left track and right track), and a preassembled horizontal member (head unit). Identify components by the Parts/Assemblies section in back of this
manual. When components are received, check for damaged, loose or missing parts. If there are damaged or
missing parts contact your RollSeal distributor immediately. Please read and understand all instructions in this
manual before beginning installation.
7.3 Adjusting the Door Framing or Clear Opening
Locate your particular system in the appropriate Tables 1-4, pages 3, 4, 5, and 7. Read the value of height and
width of the clear opening for the door size that you are installing. This gives the required dimensions of the clear
opening. If necessary, adjust the dimensions of the mounting posts or framing members to the height and width of
your D5/6 series door system as shown. Refer to Section 7.4, Page 15, Diagram 7A for details of attaching door to
framing members. Framing material must provide suitable support for attachment of screws. Make sure that
mounting posts or framing members are positioned so that the screw holes of the outer flanges of the vertical
members will align with the mounting posts or framing members (Section 7.4, Page 15, Diagram 7A).
NOTE: Make sure that there is space for appropriate motor, control box or Condensation Management
System (CMS) and freezer tracks (Freezer door option only) without encountering any
obstructions during installation. Refer to appropriate cut sheet, pages 5 and 7, and view the
appropriate drawing of the door and operator to ensure required footprint.
NOTE: Allow 1' (30.4 cm) minimum, preferably 18" (45.7 cm) clearance above the Head Unit for future
panel maintenance or replacement.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 14
7.4 Attachment Points of Door
When sizing the clear opening for attachment of the door, pay close attention to the following guidelines. Door
flanges have pre-drilled holes that serve as mounting points of door.
Flange widths are shown in Diagram 7A.
1. Make sure that door assembly is plumb & square.
2. The top unit has a top flange and a bottom flange. Make sure these flanges overlap framing.
3. The vertical members have inner flanges and outer flanges. The outer flanges have pre-drilled holes that
serve as attachment points. Make sure the outer flanges overlap framing.
4. When door is raised in front of clear opening (Section 7.7, page 17), Diagram flanges must be flush against
framing for attachment of screws.
Diagram 7A
Framing
Members
Bottom View
Framing Members
Page 15
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
7.5 Assembly of Parts
Arrange the horizontal member, left vertical member (left track), and right vertical member (right track) on
the floor in front of the clear opening as shown in Diagram 7B. The curtain side of the horizontal member
and each vertical member faces down.
Diagram 7B
End of
horizontal
Member
A
B
U-shaped
plate
3/8" x 1"
Bolts & nuts
Plate fits inside
vertical member
Slide vertical member
over U-shaped plate.
On each end of the horizontal member is a
U-shaped plate that fits inside each
vertical member. The U-shaped plate has
four bolt holes, two on the inside and two
on the outside flanges that match bolt
holes in the vertical member. See diagram
at left.
1. Align the vertical member with the Ushaped metal plate at end of horizontal
member.
2. Slide the vertical member onto the
outside of the U-shaped metal plate of
the horizontal member as shown in A.
3. Insert bolts through bolt holes as shown
in B. Install nuts. Tighten bolts & nuts
securely.
Vertical
Member
Right vertical
member
Clear Opening
At this end of members
Left vertical
member
Horizontal
member
Placement of Parts for Assembly
Lay left track, right track, and horizontal member
face down in front of the clear opening as shown.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 16
7.6 Infrared Sensor Connectors (Brother Motor Option Only)
Located at the bottom of each vertical member is an infrared detector. The detector on each vertical member
operates as a safety device if the infrared beam is interrupted. Door can be set to stop if beams are broken
while closing or to stop and reverse to the full open position. Refer to the RollSeal SC-325 Controller Manual
for more information.
1. Locate female connector on vertical member. This connector is attached to the infrared detector.
2. Locate male connector on horizontal member. Unroll cable until connectors meet. Pull enough slack to
create a service loop, such that connectors can be pulled out of tracks for photo eye replacement and
troubleshooting purposes.
3. Plug connectors together. Make sure connectors interlock.
4. Repeat for both infrared detectors.
5. Cable ties and adhesive mounts are supplied to secure wire to the inside of tracks.
Diagram 7C
NOTE: For each vertical member, unroll respective
sensor cable attached to horizontal member until
cable reaches the sensor connector attached to the
vertical member. Pull enough slack for photo eyes
replacement and troubleshooting purposes.
7.7 Fastening Door Assembly to Clear Opening
Diagram 7D
Diagonals Must Be
Within 1/8 inch
1.
Use a tape measure and make sure that the overall
height and overall width of the clear opening meet
the requirements: Overall Height = Height + 20.688
in. (52.55 cm), Overall Width = Width + 16.4 in.
(41.66 cm). Reference appropriate Table 1-4, pages
3, 4, 5, and 7.
2.
Make sure that door assembly is plumb & square.
See Diagram 7D.
Verify Dimensions
from Table 1-4
Page 17
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
3. Center door assembly on clear opening. Align the
bottom of each vertical member with the respective
framing board or posts of the clear opening.
NOTE: The vertical members should
be aligned so that their outer
flanges will exactly overlap
with the framing boards or
posts when the door
assembly is raised into
position.
4.
Assemble workers and
equipment into position on
each side of the door assembly.
IMPORTANT: SLOWLY LIFT TOP
OF DOOR ASSEMBLY TO
RAISE THE DOOR. See 0.
Diagram 7E
Drill 1/4" Hole and
Install Hammer Set
Anchors
5. Lean door assembly upright against clear opening.
6.
Carefully press flanges of the door assembly flush against faces of framing boards or posts.
7.
Fasten Tek screws (in steel) or lag screws (in wood) through the flanges on sides of door assembly.
Securely tighten all screws.
8.
On the lower and upper flanges of the horizontal member there are attachment points for fastening
screws. Fasten Tek screws (in steel) or lag screws (in wood) through the holes. This secures the top of
the door to the clear opening.
9.
Locate the two floor mounting holes at the bottom of the left and right tracks. See Diagram 7E.
10. Drill a 1/4" hole and install Hammer Set Anchors (1002-6030) in both right and left tracks. See
Diagram 7E.
11. This completes fastening of the door assembly to the clear opening.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 18
8
Mounting Operators to D5/6 Series Doors
Mounting Manaras Operator to D5/6 Series Doors – The next few pages explains specific information with
regards to mounting a Manaras on a D5/6 Series door.
!! Warning!
Prior to mounting the Manaras it is important that you read all the information contained within
this document and the Manaras Installation and Instruction Manual provided with the door.
Failure to do so could result in severe personnel injury or damage to equipment!
For more detailed information on mounting, wiring and operating the Manaras refer to the Manaras Installation and
Instruction Manual provided with the door.
Sprockets are mounted as follows on D5/6 series doors:
D5/6 series size 50-12 (small) goes on the door. Size 50-23 (large) goes on the motor. See drawing below.
Drive Shaft
Spreader Bar
Small Sprocket
Chain
Large
Sprocket
Lock Collar
Hooks & Loops Strip
(Attached to inside of
curtain and inside track
units)
Manaras Back-up
Chain Hoist
NOTE: Manaras GH Operator can be mounted in its normal upright position for all options. However it
may be necessary to remove and re-install the chain and pulley on the opposite side to prevent chain
interference. Refer to Manaras Opera GH Installation & Instruction Manual if your operator is a
gear head operator.
Page 19
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
3
4
5
1
6
NOTE: For “Front” mounted operators refer to
RollSeal Diagram 4802-6501 D5/6 Series Manaras
motor installation using the front motor mount
plate. Diagram is provided with front mounted
doors.
2
POSITION 1, 4 and 5 – GH motor mounted on left side.
Parts required – Normal size spreader bar, normal size chain, 2 collars and 2 sprockets
(1 size 50-12 and 1 50-23)
POSITION 2, 3 and 6 – GH Motor mounted right side.
Parts required – Normal size spreader bar, normal size chain, 2 collars and 2 sprockets
(1 size 50-12 and 1 50-23)
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 20
Spreader Bar Assembly
Chain Spreader Mounted On
Door and Operator Shafts
Spreader Bar
Mounting Chain Spreader
Door Sprocket
Door Shaft
Flange Bearing
Collar
Chain
3/8” Lock Nut
3/8” Split Washer
3/8” Flat Washer
Hex Head Bolt
3/8” - 16UNCx1”
Chain Not Shown
for Clarity
Operator Shaft
Operator Sprocket
3/8” Flat Washer
Flange Bearing
Collar
Length of Spreader Bar and chain may vary according to mounting option selected. For motor mounted 18” away,
the Extender Chain Spreader must be used. (See Diagram 8A)
! CAUTION!
Failure to arrange spreader bar, sprocket and collar parts in specific order could result in damage.
NOTE: If sprockets are greater than 2 feet apart you must have Extended Spreader Bar and Chain Kit
(part #’s 0404-5214 Manaris Spreader Bar and 6450-7617 Manaris Soft Chain).
9
Mounting Brother Operator to D5/6 Series Door
The Brother Operator will be mounted at the manufacture.
Below shows a D5/6 Series Door with a Brother Operator.
Refer to instructions page 28 and 29 for wiring diagrams for
Brother motor wiring.
Page 21
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
10 Installation of D5/6 Series Doors (Freezer Kit Included)
Installation of a D5/6 series Automatic Freezer Door involves connecting to the Smart Controller SC-325 or SC-650
that connects to the AC power, the door motor, the Up/Down button, and the safety beam, plus connecting the
Condensation Management System (CMS) Unit and associated duct work. Other accessories can be added such as a
remote IR sensor, a remote radio link, and door movement indicators such as lights and bells.
Condensation Management System (CMS)
Motor
(230 VAC - 3 phase)
Flexible duct not
shown for clarity.
Control Box
Flexible duct
attaches to vent
pipe on both
sides.
Limit switches are located
within the interior of
horizontal member.
See Section 14.1 for
description of limit
switches.
The D5/6 Door
requires a SC-325 or
SC-650 Controller.
Safety beams
Tension pipes are
located within folds of
curtain.
Floating Magnets and
Laminated Steel (Attached
to outside of curtain and
inside track units)
10.1 Tools Required
3/8 in. (10 mm) Power screwdriver (portable)
3/16 in. (5 mm) Drill bit and power drill
3/8 x 1 in. Bolts and nuts (supplied)
Socket
Hammer
Tape measure
Carpenter's level
NOTE: Other Tools May Be Required According To Installation.
10.2 Overview
The D5/6 Freezer Door is shipped with pre-assembled vertical members (left track and right tracks), with
floating magnets, and a pre-assembled horizontal member (head unit). Identify components by the
Parts/Assemblies section in back of this manual. When components are received, check for damaged, loose or
missing parts. If there are damaged or missing parts contact your RollSeal distributor immediately. Please
read and understand all instructions in this manual before beginning installation. After the door has been
assembled and attached to the door framing per instructions in Section 7, Page 14 of this manual it is
necessary to install the Condensation Management System (CMS) and ducts to complete the freezer door
installation.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 22
11 Installation of Condensation Management System and Ducts
Install the Condensation Management System at the top of the Freezer Door approximately in the center of the door
as shown below. Install the 5/7” Duct Adaptor in the intake side of the Condensation Management System.
Carefully run the duct work to the two couplings on the left and right track of the door. Fasten each end of the duct
with hose Clamps.
Condensation Management
System
5/7" Adaptor
Flexible
Duct
Flexible
Duct
Intake Side
Supply Side
Leave
sufficient
room for the
control panel
door to open.
Supply Side
NOTE: For all freezer applications, the
SC-325 or SC-650 controller
“P4” program setting must be
set to option “3”.
Intake Side
Hose
Clamp
Air flow through door
11.1 Connecting the Electrical Power
1.
2.
3.
4.
Page 23
Connect the RollSeal SC-325 or SC-650 Controller to Door Control Box.
Refer to the RollSeal SC-325 or SC-650 controller manual (4801-5156) for instructions on wiring.
Refer to the RollSeal SC-325 or SC-650 controller Manual (4801-5156) for initial setup.
Connect the two control wires from the Condensation Management System to the
SC-325 or SC-650 Controller.
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
12 Mounting Manual Chain Hoist to D5/6 Series Door
12.1 First Safety Bracket
The Safety Bracket is designed to lock the drive shaft (during shipping and installation) to prevent injury from
rapid drop of the door curtain. A Safety Bracket is installed on each end of the head unit. Removal of the
bracket should only be done after door is secured to structure.
! CAUTION!
Only remove the Safety Bracket from the side of the door that gets the hoist or motor, once
door is secured to wall. The Safety Bracket on the opposite side can only be removed
after the motor or hoist is installed. Removal of both Safety Brackets without motor or
hoist installed can cause serious injury or damage.
Removal of First Safety Bracket:
1. Remove cable tie and tag. Not shown below.
2. Remove the shaft locking hardware. See Diagram 12A, Detail B, Item 1.
3. Remove the two bolts holding Safety Bracket to Head Unit. See Diagram 12A, Detail B, Item 2.
4. Retain hardware and bracket for later use.
Safety bracket
Safety Bracket
Head Unit
(Track and Structure not shown)
Detail A
Shaft Lock
Typical – Both Ends
Note: Cable tie and tag not
shown.
Detail B
2
12.2 Removal of Second Safety Bracket
1. Motor or Hoist is installed.
2. Repeat Section 12.1, Steps 1-4, Page 24.
1
Safety Bracket Removal
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 24
12.3 Chain Hoist Installation
Chain Hoist can be installed on left or right side of door.
1. Remove the Safety Bracket only on the side of the door where the hoist is to be installed. Retain bracket
and hardware for later use. See Section 12.1, Page 24.
2. On shaft end of door, position U-shaped mounting bracket (6421-9393) over shaft.
3. Align bolt holes of bracket with attachment holes in door.
4. Insert bolts through cut-out openings of mounting bracket.
5. Securely attach mounting bracket to door.
6. Position Chain Hoist (6421-9339) onto mounting bracket. Align bolt holes of Chain Hoist with holes in
mounting bracket.
7. Securely fasten Chain Hoist to bracket with bolts provided.
8. Securely attach Catch Bracket to wall with self-tapping screws provided.
9. Securely hook chain into Catch Bracket as shown below.
10. Remove the Safety Bracket on the opposite side of the door from the hoist. Retain bracket and hardware
for later use. See Section 12.2.
11. Hoist installation complete. See Section 23 for Door Operation.
Chain Hoist
Attach Catch Bracket*
with two self-tapping
screws (1004-0050).
(*Appearance may
vary)
6421-9339
1004-7029
6421-9393
Brkt.
1004-6021
! Warning!
NEVER RELEASE CHAIN!
If Chain Is Released, Door Will Drop With Rapid Motion. Injury May Occur If Chain Is Released!
Page 25
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
13 Connecting Electrical Power to D5/6 Series Doors
Refer to appropriate Operator Manual (Manaras, MFZ or RollSeal SC325/650).
14 Operation of D5/6 Series Doors
Operation of D5/6 Series with Brother Motor Option and RollSeal Smart Controller.
Encoder Box
Motor (Mounted
Left Side Only)
(230 VAC - 3 phase)
Limit Switches are
located behind the
Access Panel.
See Diagram 14A for
description of Limit
Switches.
Smart Controller
SC-325 or SC-650.
Safety Beams
Tension Pipes are
located within folds of
curtain.
Floating Velcro or
Magnetic Strips
attached inside track
units and mate with
the curtain as it
close to form a seal.
Note: Impact Resistant Pipes
are available for door
sizes less than 12 feet.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 26
14.1 Limit Switches
There are three limit switches
located within the horizontal
member mechanism. See
Diagram 14A. These switches
are attached to levers that
contact the curtain.
The Home Switch establishes
the 'open' reference position of
the door curtain. This creates
the zero reference position,
Leading Edge
from which the encoder
Switch
counts the position of the
door.
Safety Switch
The Safety Switch is a fail-safe
switch that stops the curtain in the
unlikely event of malfunction of the
home switch.
Home Switch
Encoder Box
The Leading Edge Switch is a switch
that stops the curtain in the event of a
doorway obstruction.
DC Plug
AC Plug
Page 27
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
15 D5/6 Series Door Wiring Diagram (Brother Motor Only)
See Page 29
See Page 29
WARNING!
Head Unit Must Be
Properly Grounded.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 28
16 RollSeal Smart Controller Wiring Diagram
(Brother Motor Only)
See Page 28
Page 29
See Page 28
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
NOTE: Refer to the RollSeal SC-325/650 Controller Manual for wiring and initial setup. After wiring the
controller to the door, connect electrical power to the controller. The door is now ready for
operation.
The controller keeps track of the "open" and "closed" positions of the door by means of a mechanical encoder wheel
that is located in the encoder box. The controller electronically counts steps as the wheel turns to keep track of the
door position. The door seals by means of 'hook & loop’ or ‘magnetic’ strips along the edges of the door curtain and
vertical members.
To Operate Door:
1. Depress “Open” switch button mounted on the wall. Door curtain will roll up to 'open' position and find
“HOME” position and drop some to the set upper limit. If door was wired for “timer” it will count down
from set delay and close on its own. If not on wired on “timed” function proceed to step 2 to close.
2. Depress “Close” switch button. Door curtain will roll down to 'closed' position of lower limit and stay
3. Depress button to open or close door as desired.
4. Open and close the door a few times to test door operation and remove any wrinkles in the door curtain.
If you detect any problems, STOP. Disconnect electrical power. Contact your distributor for assistance.
17 Operation of D5/6 Series Door with Freezer Kit Included
The controller keeps track of the "open" and "closed" positions of the door by means of a mechanical encoder wheel
that is located in the control box. The controller electronically counts steps as the wheel turns to keep track of the
door position.
The door seals by means floating magnets and laminated steel strips along the edges of the door curtain and vertical
members.
17.1 SC-325 or SC-650 Program Setup for Freezer Mode
For all freezer door applications, the SC-325 or SC-650 controller “P4” program setting must be set to option
“3”. Option “3” will reconfigure the SC-325 or SC-650 controller “Warning” output for Freezer Mode
operation to operate freezer equipment such as blowers or heaters when wired properly (See Wiring Diagram
in the SC-325 or SC-650 controller manual 4801-5156 Connecting Switches to the SC-325 or SC-650
Wiring Option -W01). The P4 Door Interlock option 3 “Freezer Mode” is explained in detail below.
P4 - Option 3 = Freezer Mode, No Interlock
When the Freezer Door and SC-325 or SC-650 Smart Controller is used in freezer applications and P4 is set to
3, the Auxiliary Output Relay is used to operate equipment such as blowers or heaters. *Available on
Software versions V0.21 and later.

Operation of the blowers or heaters will occur ONLY while the door is closed. Closed refers to the
normal operation while the door is below Safety Beam Height.

Auxiliary Output Relay will disengage during door movement, setup operation, jog mode, etc.

Auxiliary Output Relay will engage upon the door stopping below Safety Beam Height.

If the Home Switch is engaged, the Auxiliary Output Relay will turn Off-disengage.

If the door status indicates unknown position, the Auxiliary Output Relay will turn Off-disengage.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 30
When P4 = 3 (Freezer Mode):
P5- “Freezer Mode” Auxiliary ON Time
If P4 = 3, this P5 setting, along with P6, allows the user to cycle the fan & heater On & Off. Since not
all applications are the same, some will not require as much help eliminating condensation while
others may require more. This setting, along with P6, allows the user to operate the unit as efficient
as possible.
P6- “Freezer Mode” Auxiliary OFF Time
This setting works in conjunction with P5 to complete the On/Off cycle of the condensation removal
system.
! WARNING!
When P4 Is Set To 3, The Functions Of The “Warning” Output Are Reconfigured For Freezer Operation And
Can Not Be Used For Other Functions.
Enter Program Mode – Set P4 to “3”
Settings that are usually set up when the SC-325 or SC-650 Smart Controller is installed or adjusted are
referred to as Program Parameters.

To get to the Program Mode, press and hold the Mode button for at least five seconds. When the
controller has entered the Program Mode, the display will flash between P1 and the current value of
the program parameter.

Press the Mode button three more times until the display flashes between P4 and the current value of
the P4 program parameter.

Check/verify that the current displayed parameter is set to “3”. If “3” is not the selected parameter,
the displayed parameter must be changed to “3” by pressing the Up ( ) or Down ( ) arrows.

When the P4 parameter has been set, repeatedly press the Mode button to move past all of the
following parameters and exit the programming mode.
NOTE:
P5 and P6 parameters are already set to factory default values. Do not initially adjust these values
until complete operation is confirmed and only adjust when the door & heater/fans can be monitored for
satisfactory operation.
Up/Down Arrows
Mode
Page 31
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
PROGRAM PARAMETERS
P1 - Close Time Delay (Seconds)
P2 - Acceleration Range
P3 - Deceleration Range
P4 - Door Interlock
0 - OFF
1 - Sequential Interlock
2 - Passive Interlock
3 - Freezer Mode - No Interlock
P5 – Auxiliary On Time
P6 – Auxiliary Off Time
P10 - Service Cycle Reset
0 - No
1 - Yes
P11 - Service Reminder (Cycles x 100)
P12 - Input Status
PS1 - Set Limits?
PS2 - Set Open Limit
PS3 - Set Close Limit
*Refer to the 4801-5156 SC-325 or SC-650 product manual for additional smart controller information.
17.2 Open and Close Door
1. Depress manual control button. Door curtain will unroll to 'closed' position.
2. Depress manual control button. Door curtain will roll up to 'open' position.
Depress button to open or close door as desired.
Open and close the door a few times to test door operation and remove any wrinkles in the door curtain. The
door is now ready for operation.
If you detect any problems, STOP. Disconnect electrical power. Contact your distributor for assistance.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 32
18 D5/6 Series Door Condensation Management System Wiring
Diagram
Page 33
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
19 Manual Operation D5/6 Series Door (Brother Motor Only)
19.1 Operating Instructions
The D5/6 series door can be operated manually in the event of a power outage or if there is a motor
malfunction. To operate the door manually, perform the following instructions.
!
Warning!
Disconnect All Electrical Power To Motor Before Attempting
To Operate The Door Manually!
!
Warning!
The Curtain Is Released When Brake Lever Is Disengaged.
Do Not Disengage Brake Until Door Opening Is Clear!
If door is OPEN (door curtain raised) perform the following steps:
1.
Locate brake lever at bottom of motor. (See diagram below).
2.
Carefully release brake by flipping lever down.
CAUTION: Curtain will drop when brake is released.
If door is CLOSED (door curtain lowered) perform the following steps:
1.
Turn power off to the controller
2.
Locate brake lever at bottom of motor.
3.
Carefully release brake by flipping lever down.
4.
Motor shaft is accessible from bottom of
motor. Use provided Crank Handle to
rotate motor shaft.
5.
Carefully turn motor shaft
counterclockwise to raise door
curtain.
Note: The drive (as viewed
from the 'motor end' of door) is
synchronized with clockwise or
counterclockwise rotation of the motor
shaft
5.
When door curtain has been raised
to desired height, flip brake lever
up to engage brake.
6. If you do not release the
brake it could result in
damage to the motor.
Part No 4801-5154 Rev 09-2014
Brake lever
engaged.
Crank Handle
attaches here.
D5/6 Series Doors
Brake lever
Disengaged.
BRAKE ON
BRAKE OFF
Page 34
20 Adjustment of Brake (Brother Motor Only)
After extended operation of the brake lever, the brake may become worn. As the brake wears, some adjustment to
the brake is required. Lettered diagrams below correspond to lettered instructions. Follow instructions to adjust
brake:
1.
2.
3.
4.
5.
6.
Close door curtain to fully lowered position.
Engage Brake lever.
Disconnect electrical power to motor.
Remove four Phillips screws (A).
Remove cover (B).
Straighten the bent tab (C) of spider nut.
7.
Tighten spider nut (C) snuggly against
blower wheel. Make sure a tab of spider
nut is aligned with a notch in the shaft
8. Bend tab (C) upward into notch of shaft.
9. Replace cover (B).
10. Replace four Phillips screws (A).
11. Disengage brake lever (D).
12. Adjustment complete.
C
B
A
Page 35
D
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
21 Operation of D5/6 Series with Manaras Motor Option.
Complete installation and operating instructions are provided with the Manaras Operator at the time of delivery.
Refer to these instructions for the proper installation and alignment of the Manaras operator.
After the door has been secured to its frame (as previously described), the Manaras motor has been mounted with
chain, spreader bar and associated hardware (per instructions in this manual and the Manaras installation manual),
the door will be ready to operate after completing the following steps.
! Warning!
TO AVOID THE DANGER OF POSSIBLE DAMAGE TO THE DOOR AND OPERATOR,
TRAVELLING CAMS MUST BE ADJUSTED TO THEIR APPROXIMATE POSITIONS
BEFORE MANUALLY OPERATING THE DOOR OR BEFORE
APPLYING POWER TO THE OPERATOR.
! Warning!
Do not remove the cable ties from around the door head unit until the door is installed to the
door frame and the Manaras Operator is properly installed to the door drive shaft. Without
proper support, the door will drop with rapid motion and injury may occur.
Before using the Manaras Operator’s UP/DOWN manual chain or switch controls,
ensure the shipment cable ties and drive shaft safety brackets are removed
from around the door head unit.
21.1 Limit Switches.
There are 4 limit switches. Two are used as end of travel, one is for radio-control or one-button operation and
one is for reversing devices. These switches are activated by the rotary cams traveling on a threaded shaft.
Refer to Diagram 21A, Limit Switches.
Limit Switches
“Open Position” cam
Cam Retaining Plate
“Close Position” cam
Limit Switches Lever
“Advanced Open”
Limit Switch
“Open” Limit Switch
“Close” Limit Switch
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
“Advanced Close”
Limit Switch
Page 36
! Warning!
NEVER PLACE HANDS OR TOOLS INSIDE OPERATOR OR NEAR
DRIVE MECHANISM UNLESS POWER IS OFF.
21.2 Adjustment of Limit Switches
1.
2.
3.
Open the cover of the electrical enclosure.
Manually raise the door to a nearly opened position using the Manaras manual chain. (Section 23,
Page 40, Manual Operation of Door with Manaras Operator )
Pull the traveling cam retaining bracket on the Open Position cam side and rotate the Open Position
cam. Refer to Diagram 21B, Adjusting The Limit Cams.
Note: Turning the cam towards the center of the shaft increases door travel. Turning the
cam towards the switch decreases door travel.
4.
5.
6.
7.
Manually rotate the Open Position cam until the lever activates the Open limit switch sufficiently so
as to hear the switch click.
Release and engage the retaining bracket. Make sure that the bracket engages in the slots of both
limit cams after each adjustment.
Manually lower the door to a nearly closed position and repeat steps 3 through 5 with the Close
Position cam.
Upon completion of all wiring connections, repeat steps 2 through 6 above using the "Stop" button
for adjustments of limit switches to their final, exact positions
Pull the travelling cam retaining bracket
on desired side to adjust cam position.
Adjusting the Limit Cams
Page 37
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
21.3 Wiring Options to the Manaras Operator Terminal Block

Radio Controls: Consists of a radio receiver unit and remote transmitters. These controls consist of
an RF signal being emitted on a "pulse" basis to a mated receiver tuned to the same "pulse" rate.
Once the receiver accepts the code, a relay is activated closing a set of contacts.

Photo-electric units: Can be used as opening and reversing devices. An infrared light is emitted from
the control to a reflector and back. If, during closing travel of the door, the light beam is broken, the
door will reverse to the fully open position.

Digital Keypad: Consists of a control head which is pedestal mounted. Similar to a telephone touch
pad it allows the selective coding of a four number series. Once the programmed series of numbers is
received in their set order, a relay closes and completes a circuit.

Card Reader: A magnetic-mechanical device which accepts sealed and coded cards. The cards
trigger magnets to rise in the cartridge head, releasing a lock mechanism which allows a deeper
insertion of the card. The card then contacts a switch that closes the circuit.

Key Switch: Momentary contact will open door. Can be wall or post mounted for interior or exterior
use. * Refer to Diagram 21C, Manaras Terminal Input Connections.
5
6 7
24 VAC
CLOSE
4
OPEN /
CLOSE
OPEN
3
COM
COM
1 2
SAFETY
DEVICE
STOP
24 VAC
POWER
PUSH-BUTTON STATION
8
9
L
N
Line Neutral
EXTERNAL
INTERLOCK
Ground
OPEN
CLOSE
STOP
THREE PUSH BUTTON
RADIO RECEIVER
DIGITAL KEYPAD
KEY STATION
(OPEN COMMAND)
PUSH BUTTON
(OPEN/CLOSE COMMAND)
CARD READER
(OPEN COMMAND)
PHOTO CELL
24 VAC PILOT LIGHT
(to indicate “POWER ON”)
Manaras Terminal Input Connections
NOTE:
Certain accessory devices may require additional power wiring.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 38
22.3 Switch Operation of Door with Manaras Operator
To Operate Door:
1. Depress the “Close” button on the Open/Close/Stop switch. Door curtain will unroll to 'closed'
position.
2. Depress the “Open” button on the Open/Close/Stop switch. Door curtain will open to 'Open' position.
3. Depress button to open or close door as desired.
4. Open and close the door a few times to test door operation and remove any wrinkles in the door
curtain.
5. If you detect any problems, STOP. Disconnect electrical power. Contact your distributor for
assistance.
22 Manual Operation Manaras Operator
The D5/6 door can be operated manually in the event of a power outage or if there is a motor malfunction. To
operate the door manually, perform the following instructions.
! Warning!
Do not attempt to manually operate the door while the operator is running. Do not attempt to
manually force a malfunctioning door to open or close. The chain is an emergency device
and is not designed to operate a door with serious mechanical problems.
! Warning!
NEVER RELEASE CHAIN! If Chain Is Released, Door Will Drop With Rapid Motion.
Injury May Occur If Chain Is Released!
Do not remove the cable tie securing the chain to the chain guide until after the
chain bracket is completely installed and the chain is secure. Remove and discard
the cable tie securing the chain to the chain guide prior to manual operation.
Chain Adjusting Nut
1. Pull on the hand chain in the down direction. The first foot
pulled will engage the chain hoist mechanism and disable the
electrical circuit.
2. Continue to pull the chain in the desired direction. Repeat
actions 1 and 2 in the opposite direction if the door does not
run in the desired direction.
3. To return to electrical operation, pull slightly on the chain in
the opposite direction.
5. Adjustment of the door is required if no door movement
occurs after two feet of pulled chain. To adjust, turn the
adjusting nut clockwise (See Diagram 22A) by ¼ turn until
the hoist engages after pulling one foot of chain.
NOTE: If the nut is too tight, the manual torque
on the chain will be too heavy.
Page 39
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
23 Operation of D5/6 Series with Manual Chain Hoist Option
! Caution!
NEVER RELEASE CHAIN WHILE DOOR IS BEING RAISED OR LOWERED!
You must maintain tension on chain while door is lowered to
prevent rapid drop (closing) of the door.
Manual Operation with Chain Hoist
1.
2.
3.
Carefully pull chain to open (Raise) door.
When door is fully raised, securely hook chain into Catch bracket as shown
in Chain Hoist Instructions.
To Close (Lower) door, securely hold chain. Unhook chain from bracket.
Gradually close door.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 40
24 Emergency Egress
The Emergency Egress feature provides a simple and convenient means of exiting a Roll Seal D5 Door from the
inside of the structure should the door motor become inoperative due to a power failure or other conditions.
24.1 Installation
Install the two Strap Retainers (1040-8400) to the left or right side outside of door jamb as shown below. For
a wood framed door jambs use two #10 x1 screws (1004-1386). For a metal framed door jamb use two
#8x1/2 Tek screws (1004-2492). See Diagram 24A.
Diagram 24A
Diagram 24B
Install the
Emergency Egress
Tool Retainers on
the door jam
PRESS
TO
RELE ASE
Diagram 24C
24.2 Exiting (Opening) The Door
1.
2.
3.
Remove Emergency Egress Tool from the
retainers on the side of the door.
Connect the hook end of the tool to the DRing on the top of the door frame. See
Diagram 24B.
Pull down on the Egress Strap. The Door
will raise approximately half way up. The
door will open enough for a person to exit
the structure. See Diagram 24C.
.
Page 41
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
24.3 Resetting (Closing) The Door
After the RollSeal D5 Door is opened by using the Emergency Egress Strap, the door must be carefully
re-set to ensure proper operation in the future.
!
CAUTION!
When the Cam Buckle is released, the door will rapidly close unless tension is held on the strap.
Keep fingers away from buckle while closing.
1.
Firmly hold strap. See Diagram 24D.
2.
Press the Cam Buckle Release. See Diagram 24E.
3.
Gradually feed strap through Cam Buckle until door is closed at bottom.
4.
Return Emergency Egress Tool to retainers for future use.
5.
Cycle the door up and down in normal operating mode to ensure proper re-setting of the door.
Adjust if necessary. Door should now function normally.
Diagram 24D
Diagram 24E
Press the
Cam
Buckle
Release
Firmly
hold
strap.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 42
25 Egress Strap Removal/Re-Installation
25.1 Removal
1. Locate the door controller and turn off the power switch on the left side of the controller.
2. Remove the door’s head unit cover.
3. Place the door in the JOG mode by holding the Up and down arrows on the controller at the same time
until you see “JOG” in the controller’s display.
Warning!
Watch the panel closely while you are slowly jogging/rolling the curtain up on the drive shaft.
Stop when you see the area where the long egress strap is connected to the
short egress piece attached to a triangle panel. This should bring the
strap and connection point, right to the top for easy access.
Failure to stop can cause curtain to reverse direction and damage door components.
4. Find the area where 2 loops are attached with a quick-link, unscrew the quick-link that attaches the long
yellow strap loop to the yellow loop of the triangle piece. Make sure not to drop the weight into the door.
5. Access the inside area of the cooler/freezer box through the door opening. If the strap is hanging inside,
unhook and remove the gold buckle and the damaged yellow strap (top center of door) from the door
25.2 Installation
1. Locate the door controller and turn off the power switch on the left side of the controller.
2. Remove the door head unit cover if it has not been removed previously.
3. Un-roll the yellow egress strap with attached gold buckle.
NOTE: Insert the strap through the hole in the center of the door, near the top, where
original strap was traveling down inside the curtain and replace the old gold
buckle with the new one.
4. Proceed to the outside area and locate the roller assembly at the top center of the door where the original
strap came into the curtain area from the inside cooler/freezer area. Use anything with some stiffness
(banding material) and feed the stiff item through the roller and down through the slot located in the inside
cooler/freezer area and tape or tie it to the small loop (not the D-ring) of the yellow strap. Then gently
pull it through the hole and roller assembly at the top/center of the door.
5. Ensure the yellow strap is not twisted. Place the counter weight onto the yellow strap.
6. Attach the new strap (small loop) that you just pulled into the curtain area to the (small loop) strap on the
traingle piece of panel using the quick-link.
7. Attach the gold buckle to the door frame.
8. With the controller still in JOG mode, use the down arrow to lower the door to the floor. Exit JOG mode
by holding the Up and Down arrows on the controller at the same time until you see “---” in the display of
the controller.
9. Press Open on the 2 button switch. The door should open, timeout, and close. If it does, run it open and
close several times. If it works well then go to step 10. If not, notify tech support of the manufacturer.
10. Re-attach the cover.
Page 43
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
26 Door Panel Adjustments
During normal operation, the tension pipes should run in close proximity of each other. The clearance between the
tension pipes should normally be between 1/4 to 1/2 (6.35 mm - 12.7 mm). See Detail 3 below. There are two
situations pertaining to the tension pipes that may cause problems with door operation. If the tension pipes are too
far apart, the tension pipes will not repel each other. This causes poor contact between the hook & loop or
magnets. On the other hand, if the tension pipes are riding one another (i.e. touching one another), the door panel
material does not flow evenly, thus leaving wrinkles in the panel instead of a stretched, smooth & even appearance.
Adjustment Procedures
The clearance between the tension pipes can be adjusted by raising or lowering the door panels. Each door has three
panels: (1) the inside panel (panel facing the inside of building) is attached to the back plate. (2) The center panel is
attached to the roller. (3) The outside panel (facing the outside of building) is attached to the front bar. Adjustments
are made to the inside panel and/or the outside panel.
NOTE: The door must be in the closed position for panel adjustments. Ensure the
panels are not damaged while removing or reinstalling the nuts and screws.
To adjust the height of the outside tension pipe, raise or lower the outside door panel by detaching the panel hook &
loop from the front bar, and raising or lowering the panel. Then re-attach the panel loop to the hook on the front bar.
Be sure to keep the tension pipe level during this procedure.
To adjust the height of the inside tension pipe, raise or lower the inside door panel by detaching the panel hook &
loop from the back plate, and raising or lowering panel. Then re-attach the panel loop to the hook on back plate. Be
sure to keep tension pipe level during this procedure. Install Tek screws through the panel material and into the
back plate to securely hold the material in place.
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 44
27 Removal of Existing Panel
1. Lower the panel to the floor.
2. Locate the door controller and turn off the power.
3. Remove and lower the cover from the door head unit.
4. Locate the 3 fabric sheets that make up the entire door curtain. See Diagram 28A, Detail 2, Page 46. The
center panel has a hook & loop strip across the top. The center panel does not have magnets or hook & loop
strips on the sides. The inside and outside panels have hook & loop strips at the top, and magnets or hook &
loop strips along the sides of the panels. The outside panel may be identified as the longer of the two panels.
5. Mark the end of each sheet and along the edge of each sheet with a marker. This will prove vital to ensure
you install the new panel sheets at the proper locations to alleviate major curtain adjustment.
6. Remove the 3 screws from each sheet (front, center, and back). See Diagram 28A, Detail 2, Page 46. Detach
the hook & loop area of each sheet left to right, starting with front, then center, and then back sheets. Let the
panel/curtain fall to the floor.
NOTE: If the door is equipped with an egress assembly you will see the yellow egress
strap attached to a triangle piece of material with a quick-link connector. If it does
not have this strap, read the notes below and proceed to next step 8.
7. UN-screw the quick-link connector and allow the panel to lower to the floor.
NOTE: Observe how the tension pipes are installed before removal. They MUST be reinstalled first, with one pipe in the front/outer pocket (closest to outside of the cooler)
and the other pipe in the back/inside pocket. Locate the back pipe behind the
triangle piece that is attached to the yellow strap. The front/outer pipe will always
hang lower than the back/inside pipe.
NOTE: Failure to install properly could result in door sticking up.
8. Slide the 2 tension pipes out of their respective pockets. Remove the panel/curtain away from the door. You are
now ready to install the new panel/curtain.
28 Installation of Replacement Panel
1.
Place the new panel in front of the door opening and make sure the part number label is on the left side.
NOTE: If door is equipped with egress system yellow strap ensure that the strap is
positioned to the front side of the back/inside panel to allow connection to the triangle
piece of material with the quick-link connector.
2.
Take the back/inside curtain (Diagram 28A, Detail 1 & 2, Page 46) and attach the material to the
backplate placing material on the marks that were created during removal of old panel.
3.
After the inside curtain has been attached, attach the egress strap (if equipped) to the triangle piece of
material with the quick link connector.
4.
Take the outside curtain (Diagram 28A, Detail 1 & 2, Page 46) and attach to the top bar.
NOTE: Ensure all roller switches (home, safety and leading edge) are pointing down.
5.
After the curtain has been secured, install the bottom pipes in the curtain as shown in Diagram 28A, Detail
3, Page 46. The front pipe should be installed first. Then the back pipe is placed in front of inside panel but
behind the yellow strap and triangle piece of material. It should be above the front pipe
6.
Ensure all panels are inside the tracks on both sides. Set the controller to JOG mode by holding both arrows
at the same time until you see “JOG” on the display. JOG up and down, using up and down arrows to
straighten the panel. Exit JOG mode by holding both arrows at the same time. Run the door as normal.
Page 45
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
Curtain Installation
Main Drive
Roller
Center
Curtain
Inside
Curtain
Center
Curtain
Inside
Curtain
Outside
Curtain
Detail 1
Outside
Curtain
Pan head
Screw
Hook &
Loop
Strip
Bottom Bars
Detail 3
Hook &
Loop
Strip
Inside
Curtain
Hook & Loop
Strip
Outside Curtain
Center Curtain
Detail 2
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 46
29 Removing and Replacing Floating Magnets or Velcro
1.
Open the door to its upper limit. It will be necessary to raise the panel as high as it will go into the head unit.
Refer to manual operation of associated operator as shown previously in this manual. This will make it easier
for you to remove and re-install the “Floating Magnets or Velcro and PIM Plate Assemblies” from the left and
right side tracks (Diagram 29A).
Ensure panel is
raised into the head
unit.
Diagram 29A
!
Warning!
Ensure power is turned “OFF” to prevent door movement while removing
PIM Plate Assembly and Floating!
Page 47
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
2.
After you have raised the panel into the head unit, you can remove all of the PIM Plate nuts from both sides.
Then remove the PIM plate and floating assemblies from their associated tracks (Diagram 29B and Diagram
29C).
Remove
all the PIM
nuts from
top to
bottom
Squeeze the
floating
around the
PIM Plate and
pull the PIM
plate
assembly and
floating out
away from the
track
assembly.
Diagram 29B
Diagram 29C
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 48
3.
Lay the PIM plate assembly down on the floor and remove the old floating material from the PIM plate.
Pay particular attention to the top of the PIM plate assembly. You will notice the material, at the top, has
been cut at an angle. It will be necessary to re-install the new piece in the same arrangement as the one you
have removed (Diagram 29D and Diagram 29E). Get the new piece of floating material. Flip the new
piece upside down with the magnets or Velcro toward the floor. Align the pre-drilled holes of the material
with the PIM bolts on the PIM plate assembly. You might find it easier to start at one end with the first PIM
bolt, insert it, and then move to the other end slightly lifting the PIM plate in a bend to insert the PIM bolt
at that end (Diagram 29F). Lay the assembly back down on the floor flat. This will slightly pull the
material allowing the remaining holes to align properly. Proceed to insert the rest of the PIM bolts in their
proper holes. Repeat the same steps for installing the floating to PIM plate for the other side.
Diagram 29D
Remove the “old” floating
and discard. Re-install the
“new” floating
Lay the new floating next to the
PIM plate with top of floating
(Angled Cut) material to top of
PIM plate. Flip the floating
over the PIM Plate with
magnets or Velcro against the
floor then attach the floating
over the PIM Plate Bolts
Diagram 29E
Re-install the
“new” floating. It
may be necessary
to bend one end of
the PIM plate up to
attach onto the
end PIM bolt.
Diagram 29F
Page 49
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
3.
Grab and hold the PIM plate assembly and floating in a manner that will prevent the floating material from
coming off of the PIM bolts. Re-install the PIM plate assembly in the track starting with the top PIM bolt.
Align the PIM bolts with the holes in the track (Diagram 29G). Firmly press the PIM bolts into their associated
holes and attach the PIM nuts to the PIM bolts but do not tighten until all bolts have been installed. After all of
the PIM bolts have been installed, tighten the nuts pulling the PIM plate firmly against the track (Diagram
29H).
Squeeze the
floating around
the PIM Plate
and push the top
in the track
assembly first.
Align all PIM
bolts with holes
in the track
assembly
After all of the
PIM bolts have
been installed,
tighten the nuts
pulling the PIM
plate firmly
against the track
Diagram 29G
Diagram 29H
!
Warning!
Do not over tighten!
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 50
4.
Repeat steps 1-4 above for opposite side.
5.
It will be necessary to lower the panel, down, out
the head unit (Diagram 29I). Refer to manual
operation of associated operator as shown
previously in this manual. This will lower the panel
below the upper limits and turn off the safety switch
to allow normal operation.
6.
OPEN” and “CLOSE” the door several times to
ensure smooth operation and proper setting of upper
and lower limits
Diagram 29I
Page 51
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
30 D5/6 Door Options and Accessories
Description
Notes
Brother
Brother Operator
Left Mount only
115 VAC, 1/4 hp
Optional - Select prior to order
230 VAC, 1/4 hp
Optional - Select prior to order
230 VAC, ½ hp
Standard
Radio Remote Receiver
Optional - Select prior to order
Radio Remote Transmitter
Optional - Select prior to order
Motion Detector, All Motion
Optional - Select prior to order
Motion Detector, Programmable
Optional - Select prior to order
Loop Detector, Single Loop
Optional - Select prior to order
Loop Detector, Dual Loop
Optional - Select prior to order
Manaras
Manaras Operator
6 Mounting Options: Left/Right/Front/below, above
115 VAC, 8.6 A, Single Phase, ½ hp
Optional - Select prior to order
230 VAC, 4.1 A, Single Phase, ½ hp
Optional - Select prior to order
208 VAC, 2.2 A, 3 Phase, ½ hp
Optional - Select prior to order
460 VAC, 1.1 A, 3 Phase, ½ hp
Optional - Select prior to order
115 VAC, 13.4 A, Single Phase, 1 hp
Optional - Select prior to order
230 VAC, 6.7 A, Single Phase, 1 hp
Optional - Select prior to order
208 VAC, 3.4 A, 3 Phase, 1 hp
Optional - Select prior to order
460 VAC, 1.7 A, 3 Phase, 1 hp
Optional - Select prior to order
Radio Remote Receiver
Optional - Select prior to order
Radio Remote Transmitter
Optional - Select prior to order
Motion Detector, All Motion
Optional - Select prior to order
Motion Detector, Programmable
Optional - Select prior to order
Loop Detector, Single Loop
Optional - Select prior to order
Loop Detector, Dual Loop
Optional - Select prior to order
Mounting Plate, Galvanized
Optional - (Manaras Operators Only)
Mounting Plate, Aluminum
Optional - (Manaras Operators Only)
Safety Cover, NEMA 1
Optional - (Manaras Operators Only)
Front Mounting Plate, Galvanized
Optional - (Manaras Operators Only)
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 52
Description
Notes
Manual Chain Hoist
Left or Right Side Mounting
Fabric
Frost, white, blue, green, tan, black, red, anti-static
Optional - Select prior to order
Fabric Repair Kit, 18" x 18"
(Clear/Frost, White, Blue, Black, etc.)
Optional - Specify required color.
Heavy fabric, black, blue
Optional - Specify required color.
Window
Optional - Specify size prior to order
Switches
Push-Button Switch (Additional)
Optional - Select prior to order
3 Position Switch, encl button (Open / Close / Stop)
Optional - Select prior to order
3 Position Switch, with Lockout
Optional - Select prior to order
Ceiling Pull Switch, SPST
Optional - Select prior to order
Open / Close Indicator Switch Assembly
Optional - Select prior to order
Photo Eyes
Optional - Select prior to order (Safety Beams)
Freezer Kit
Page 53
D5/6 Series Doors
Part No 4801-5154 Rev 09-2014
Part No 4801-5154 Rev 09-2014
D5/6 Series Doors
Page 54
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising