Cooling System Components Catch Tanks Davies Craig Electric

Cooling System Components Catch Tanks Davies Craig Electric
Prices shown are current as of January 14, 2017.
Catch Tanks
Filtered Breather Catch Tank
Our compact one quart breather tank
can be used to vent a dry sump tank,
rear end, or any other application that
requires a filtered breather catch tank.
The 3 1⁄4’’ diameter aluminum tank has
one 1⁄4 NPT inlet and one 3 ⁄8 NPT
inlet near the top. A drain petcock is
provided at the bottom, and a special low-profile sintered bronze filter
on the top keeps the overall height
under 13''. Includes a T-bolt mounting
clamp. Meets SCCA requirements.
1 Quart Breather Tank
Part No. 2582-001 . . . . . . . . . . $157.99
Universal Catch Tank Kit
This square plastic catch bottle
features a full two quart capacity.
Molded 3 ⁄8'' nipples at the top
and bottom allow you to use this
bottle as a coolant expansion tank
if desired. For catch tank use, the
bottom nipple should be capped.
Translucent plastic makes it easy
to read the fluid level. A steel wire
mounting basket is included for
easy installation. Measures 6’’ W x 4 1⁄ 2’’ D x 8’’ H (6 3 ⁄8’’ x 5’’
with basket). Meets SCCA requirements.
Universal 2 Quart Catch Tank / Expansion Tank Kit
Part No. 2582-102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $36.99
Plastic Catch Bottle Our round,
one quart catch bottle is made from
high-temperature plastics to stand
up to hot oil and coolant. A heavyduty screw-on lid prevents leaks. The
bottle is undrilled so you can position
your vent hose anywhere you need it.
The translucent plastic makes it easy
to see when the bottle needs to be
emptied. Measures 3 5 ⁄8’’ diameter x
8’’ high overall. Mounting bracket is
not included. Meets SCCA requirements.
1 Quart Plastic Catch Bottle
Part No. 2581 . . . . . . . . . . . . . . . $14.99
Cooling System Components
Machined Aluminum Filler Neck
If you fabricate your own
aluminum radiators or
swirl tanks and require a
quality filler neck that can
be welded on without
distorting from the heat,
then this is the part for
you. Our aluminum filler neck is machined from a solid
billet of 6061-T6 aluminum stock. This is not a flimsy, easily distorted stamped fitting. It can withstand the heat of
welding without warping, so the cap will seal properly
when the job is done. A threaded nipple is provided for
connecting the overflow tube. Accepts any standard
automotive radiator cap such as the Stant racing caps
shown at right.
Aluminum Filler Neck . . . . . Part No. CM 80-092 . . . . $25.99
Stant Racing Radiator Caps
Water Expansion Tank
Raising coolant pressure with a high-pressure radiator cap
will increase the coolant boiling point, which helps to prevent overheating. Before installing one, have your cooling
system pressure checked to ensure that it can handle the
increased pressure. Specify nominal pressure: 20 psi (vents
between18-22 psi) or 23 psi (vents between 21-25 psi).
Standard Cap . . . . . . . . . . . . . Part No. 1290-Press . . . . $19.99
Lever Cap . . . . . . . . . . . . . . . . . Part No. 1590-Press . . . . $23.99
The lever allows you to release system pressure before
removing the cap.
An expansion (fill) tank is recommended for all applications where
the top of the radiator is mounted
lower than the top of the engine.
Mounting the tank higher than
the engine ensures a complete
fill and provides an air space for
expansion. Our lightweight aluminum tank has a 1.25 quart capacity
and accepts a standard radiator
cap such as the Stant racing caps at left (sold separately).
A 1⁄ 2 NPT female port on the bottom and a 3 ⁄8 NPT female
port on the side make plumbing easy. Measures 7 3 ⁄8'' tall
overall x 3 3 ⁄16'' deep x 4 5 ⁄8'' wide (6 9⁄16'' wide including
mounting tabs).
Water Expansion Tank . . . . . . . . . Part No. 2584 . . . . $112.00
lift off the throttle. Davies Craig electric pumps and fans solve all of those problems by
running completely independent of engine speed. They can even be run after the engine
is off to avoid heat soak. The Davies Craig controller automatically runs the pump and
fan just as much as required to maintain the coolant temperature you set. Davies Craig
pumps and fans are suitable for racing or street vehicles.
Davies Craig 12 Volt Electric Water Pump Kits with LCD Controller
Davies Craig 12 Volt Electric Cooling Fans
Davies Craig Electric Water Pump Kits can be
installed on virtually any vehicle with a water-cooled engine
and a 12 volt electrical system. Multiple pumps can be run
on a single engine to further increase capacity. (For example,
the Ferrari 550 GTO Le Mans cars used two EWP80 pumps,
one on each cylinder bank of the V-12 engine.) Each of these
kits includes a Davies Craig LCD Controller (described in
detail below).
Alloy pumps have an aluminum alloy body for strength. The inlet and outlet are designed
to accept a 1 1⁄ 2'' ID coolant hose, but they also have 1'' NPT female threads for more
plumbing flexibility. Nylon pumps (shown) have a composite-reinforced nylon body for
light weight. Inlet and outlet accept 1 3 ⁄8'' ID coolant hose.
The EWP150 can flow up to 150 liters per minute. This pump is suitable for the most
highly-modified racing engines and turbocharged applications.
EWP150 Alloy Electric Pump & LCD Controller Kit . . . . . . . . . Part No. DC8870 . . . . . . $519.00
The EWP115 can flow up to 115 liters per minute. It is recommended for stock, normallyaspirated V6 and V8 engines up to 3.5L.
EWP115 Alloy Electric Pump & Controller Kit . . . . . . . . . . . . . . Part No. DC8850 . . . . . $469.99
EWP115 Nylon Electric Pump & Controller Kit . . . . . . . . . . . . . Part No. DC8830 . . . . . $444.99
The EWP80 can flow up to 80 liters per minute. It is recommended for stock, normallyaspirated engines up to 2.0L (including FF1600 and Pinto-engined FF2000/FC/S2000).
EWP80 Nylon Electric Pump & Controller Kit . . . . . . . . . . . . . Part No. DC8807 . . . . . $444.99
This pump has replaceable bolt-on inlet and outlet fittings for versatility.
Davies Craig LCD Controller
The Davies Craig LCD Controller can control any
Davies Craig electric water pump and an electric fan.
The controller automatically adjusts the rate of coolant
flow to maintain the temperature you set. It can even
be wired to run after engine shut-down. Simply set your
desired engine temperature and let the controller do the
rest! The 2 3 ⁄4'' wide LCD display even has a temperature
gauge for easy monitoring. Works on 12 or 24 volts DC.
Davies Craig LCD Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Part No. DC8000 . . . . . $239.99
Includes temperature sensor and in-line sensor manifold for 1 5 ⁄16'' - 1 5 ⁄8'' ID hose.
1-800-688-6946 (Fax: 262-317-1201) Davies Craig Electric Cooling Fans free up horsepower
while providing more constant airflow. The unique reversible
design can be installed as a pusher (upstream of radiator)
or puller (downstream) depending on your application. Six
different sizes are available to suit nearly any application. The
largest sizes (14'' and 16'') measure less than 4'' deep. Sizes
smaller than 14'' are less than 3'' deep to fit in just about any
engine compartment. Fan only; Wiring and Mounting Kit is
sold separately. All of these fans run on 12 volts DC.
Davies Craig Electric Fan, 8'' (5A, 200-300 CFM) . . . . . . . . . . Part No. DC0135 . . . . . . . . $78.99
Davies Craig Electric Fan, 9'' (6.5A, 350-450 CFM) . . . . . . . . Part No. DC0160 . . . . . . . . $79.99
Davies Craig Electric Fan, 10'' (7A, 500-600 CFM) . . . . . . . . . Part No. DC0145 . . . . . . . . $78.99
Davies Craig Electric Fan, 12'' (9A, 600-700 CFM) . . . . . . . . . Part No. DC0162 . . . . . . . $109.99
Davies Craig Electric Fan, 14'' (13A, 850-1200 CFM) . . . . . . . Part No. DC0107 . . . . . . . $172.99
Davies Craig Electric Fan, 16'' (19A, 1200-1500 CFM) . . . . . . Part No. DC0166 . . . . . . . $182.99
Wiring and Mounting Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Part No. DC1000 . . . . . . . $33.99
For any Davies Craig electric fan listed here. Includes wiring harness, 12 volt relay, and all
necessary mounting hardware.
Davies Craig 12 Volt Electric Booster Pump
Originally designed to supplement standard coolant pumps, Davies Craig Electric Booster
Pumps have become popular for a wide range
of water pumping applications where the EWP80
would be overkill. They can replace the powerrobbing mechanical water pump on motorcycle
engines and shifter karts, boost flow to the heater
core in your tow vehicle for better heating, or cool
off a hot engine or turbo after shut-off. Inlet and
outlet both fit 3 ⁄4'' ID hose. Each kit includes wiring
harness, instructions, and adapters to 5 ⁄8" and 1⁄ 2" hose.
EBP15 Electric Booster Pump Kit, 15 liters/min . . . . . . . . . . . . Part No. DC9001 . . . . . $148.99
EBP23 Electric Booster Pump Kit, 23 liters/min . . . . . . . . . . . .Part No. DC9050 . . . . . . $169.99
EBP25 Electric Booster Pump Kit, 25 liters/min . . . . . . . . . . . .Part No. DC9005 . . . . . . $192.99
EBP15 is recommended for karts and stock motorcycles to 500cc. EBP23 can be used on
stock motorcycles to 1000cc. EBP25 is suitable for motorcycle-engined P2 cars.
PegasusAutoRacing.com
Check website to verify current pricing
79
COOLING
SYSTEMS
Davies Craig Electric Coolant Pumps and Fans
Mechanical coolant pumps and fans are a compromise at best. If they are powerful
enough to cool the engine at idle, they will cavitate or stall at high RPM. If you re-tune
them for high-RPM performance, you will overheat on the grid. They also rob valuable
horsepower through parasitic drag. Mechanical pumps and fans even cost you time
when shifting gears because their inertia prevents engine RPMs from dropping when you
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising