A Picture to Remember
A Picture to
Remember
Anamorphic Lens
HD-6000FX
Anamorphic Lens
HD-6000FX
Setup Instructions
Bringing the lens into the use:
STEP 1
Lift the lens up and flip it upside down in a
stand. By using the L-wrench, 5 mm carefully
remove the delivery lock screw of large lens
from the bottom plate (Fig 1-a). After this
release the two upper screws of front element
(Fig 1-b) by using the L-wrench 3mm.
c)
c)
a)
c)
c)
b)
b)
Fig 1
STEP 2
Remove the bottom plate (Fig 2) of housing by
releasing the four screws on the bottom plate
(Fig 1-c). Now carefully take off the plastic cover
coats from both sides of both lenses. Remove
also the cover coats from both IR windows of
motor box.
Fig 2
INSTALLATION INSTRUCTIONS
Parts list:
Carefully remove and unwrap all the
contents of box. Referring to the parts
list, make sure you have everything
needed to proceed with the installation
of the lens. If any parts are missing,
contact Prismasonic immediately.
„
„
„
„
„
„
„
„
„
„
Inspect the lens to make sure there are
no shipping defects. If you notice a
problem with the lens itself, or the lens’
mechanical system, contact Prismasonic
immediately.
Lens Unit
Table Stand
Power Cord
Power Converter
Remote Controller
L-Wrench, 3 mm
L-Wrench, 4 mm
L-Wrench, 5 mm
Black cap
Instruction Manual
a)
a)
b)
a)
c)
a)
c)
STEP 3
Insert the bottom plate back to the housing and
prepare to affix the four screws (Fig 3-a) with Lwrench, 3mm. Tighten the screws securely. Also
insert the black cap into the slot of bottom plate
(Fig 3-b).
Now also attach the two cap screws of front plate
back to their places (Fig 3-c).
Flip the lens back upright in a stand. Your lens is
now ready for the setting up!
Fig 3
Anamorphic Lens
HD-6000FX
Setup Instructions
Setting up the system:
Anamorphic Lens
HD-6000FX
Setup Instructions
STEP 6
Make sure the power cord has been connected
to the lens motor box. Now adjust the lens
focus. Using the remote control, press and hold
“in” or “out” (Fig 6) until the 2.40:1 picture gets
focused. It is helpful to use a test grid to monitor
when the horizontal and vertical lines in picture
become in focus simultaneously.
STEP 4
Make sure the projector is turned on. It is helpful
to have a picture that fills the entire panel of 16:9
projector. With a 2.40:1 source material the
vertical expand is good to be performed to the
picture at this step (Fig 4).
Now carefully adjust the focus of projector. Also
make sure the image is symmetrically in the
center of the 2.40:1 screen.
Fig 6
a)
Fig 4
STEP 5
Carefully position the lens with a stand in front of the projector, with the small opening closest to the
projector lens and the large opening pointing towards the screen.
Now manually adjust the lens in a stand. Make sure the entire beam fits centered within the two lenses
(Fig 5). Lower, raise, turn and tilt the lens until the desired height and angle is reached, and the picture
is symmetrically in the center of the 2.40:1 screen.
NOTE: The optimum symmetry for the projected picture can only be found by tilting the lens to the direction
of the beam
Fig 7
b)
STEP 7
In case the friction based lens height (Fig 7-a) or
the tilt (Fig 7-b) adjusting mechanism become too
loose, it is possible to get them tightened with the
set screws of stand drums on both sides of lens.
Use the L-wrench, 4 mm for tightening the
screws.
You’re done. Enjoy your new 2.40:1 picture!
Maintenance:
Your Prismasonic lens was designed to require
very minimal cleaning. It is best to only wipe the
lens housing with a clean, damp, soft cloth when
needed.
Cleaning the optics:
Only use optically safe lens cleaning solutions
and a clean, lint-free cloth certified for cleaning of
lens materials. In order to clean the optics from
both sides, the bottom plate can be temporarily
removed.
Fig 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising