OPERATORTS MANUAL
Operator’s Manual
Twin Rear Bagger — Model 19B70004OEM
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-08745
(January 7, 2013)
1
To The Owner
Thank You
Thank you for purchasing a bagging attachment manufactured
by MTD. It was carefully engineered to provide excellent
performance when properly operated and maintained.
Please read this entire manual prior to operating the equipment.
It instructs you how to safely and easily set up, operate and
maintain this attachment. Please be sure that you, and any
other persons who will operate the machine, carefully follow the
recommended safety practices at all times. Failure to do so could
result in personal injury or property damage.
If you have any problems or questions concerning this
attachment, phone your local authorized MTD service dealer
or contact us directly. MTD’s Customer Support telephone
numbers, website address and mailing address can be found on
this page. We want to ensure your complete satisfaction at all
times.
Throughout this manual, all references to right and left side of the
machine are observed from the operating position
All information in this manual is relative to the most recent
product information available at the time of printing. Review this
manual frequently to familiarize yourself with the attachment,
its features and operation. Please be aware that this Operator’s
Manual may cover a range of product specifications for various
models. Characteristics and features discussed and/or illustrated
in this manual may not be applicable to all models. MTD
reserves the right to change product specifications, designs and
equipment without notice and without incurring obligation.
Table of Contents
Safe Operation Practices......................................... 3
Carton Contents & Hardware Packs....................... 6
Assembly & Installation........................................... 8
Operation.................................................................16
Parts List...................................................................18
Warranty...................................................Back Cover
Record Product Information
Model Number
Before setting up and operating your new equipment, please
locate the model plate on the equipment and record the
information in the provided area to the right. You can locate the
model plate by looking at the topside of the bagger cover. This
information will be necessary, should you seek technical support
via our web site, Customer Support Department, or with a local
authorized service dealer.
Serial Number
Customer Support
Please do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this machine, you can seek help from the experts. Choose from the options below:
2
◊
Visit us on the web at www.mtdproducts.com
◊
Call a Customer Support Representative at (800) 800-7310 or (330) 220-4683
◊
Write us at MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019
Important Safe Operation Practices
2
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
DANGER! This attachment was built to be used according to the safe operation practices in
this manual. Carelessness or error on the part of the operator can result in serious injury.
Mowers are capable of amputating hands and feet and throwing objects. Failure to observe
the following safety instructions as well as the instructions provided with your mower, could
result in serious injury or death.
General Operation
1.
2.
3.
4.
5.
Read, understand, and follow all instructions on your
equipment and in their manuals before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
To help avoid blade contact or a thrown object injury, keep
bystanders, helpers, children and pets at least 75 feet from
the mower while it is in operation. Stop machine if anyone
enters the area.
Thoroughly inspect the area where the equipment is to be
used. Remove all stones, sticks, wire, bones, toys, and other
foreign objects which could be picked up and thrown by
the blade(s). Thrown objects can cause serious personal
injury.
Always wear safety glasses or safety goggles during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
Do not operate the mower without the discharge cover
or entire grass catcher in its proper place. A missing
or damaged discharge cover or grass bag attachment
component may result in thrown objects or blade contact
injuries.
6.
Do not put hands or feet near rotating parts or under the
cutting deck. Contact with the blade(s) can amputate
hands and feet.
7.
Shut off mower’s engine and wait for blades to come to
a complete stop before unclogging mower’s discharge
opening or bagger parts.
8.
Slow down before turning. Operate the machine smoothly.
Avoid erratic operation and excessive speed. Be aware
that a grass catcher attachment can affect the handling
characteristics of your mower.
9.
Disengage blade(s), set parking brake, stop engine and wait
until the blade(s) come to a complete stop before opening
bagger attachment’s top cover, removing grass catcher,
emptying grass, unclogging chute, removing any grass or
debris, or making any adjustments.
10.
Never leave a running machine unattended. Always turn
off blade(s), place transmission in neutral, set parking
brake, stop engine and remove key before dismounting.
11.
Your machine is designed to cut normal residential grass of
a height no more than 10”. Do not attempt to mow through
unusually tall, dry grass (e.g., pasture) or piles of dry leaves.
Dry grass or leaves may contact the engine exhaust and/
or build up on the mower deck presenting a potential fire
hazard.
12. If situations occur which are not covered in this manual, use
care and good judgment. Contact your customer service
representative for assistance.
Slope Operation
Slopes are a major factor related to loss of control and tip-over
accidents which can result in severe injury or death. Attachments
can also affect the stability of the machine. All slopes require
extra caution.
For your safety, use the slope gauge included as part of this
manual to estimate the angle of slopes before operating this
machine on a sloped or hilly area. If the slope is greater than 10
degrees as shown on the slope gauge, do not operate the mower
with the grass bag attachment installed on that area or serious
injury could result.
Do:
1.
Mow up and down slopes, not across. Exercise extreme
caution when changing direction on slopes.
2.
Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.
3
3.
Use slow speed. Choose a low enough speed setting so
that you will not have to stop or shift while on the slope.
Tires may lose traction on slopes even though the brakes
are functioning properly. Always keep machine in gear
when going down slopes to take advantage of engine
braking action.
4.
Follow the manufacturer’s recommendations for wheel
weights or counterweights to improve stability.
5.
Keep all movement on the slopes slow and gradual. Do
not make sudden changes in speed or direction. Rapid
engagement or braking could cause the front of the
machine to lift and rapidly flip over backwards which could
cause serious injury.
6.
Avoid starting or stopping on a slope. If tires lose traction,
disengage the blade(s) and proceed slowly straight down
the slope.
General Service
1.
Before cleaning, repairing, or inspecting, make certain the
blade(s) and all moving parts have stopped. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
2.
Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
3.
Never tamper with your mower’s safety interlock system
or other safety devices. Check their proper operation
regularly.
4.
Never attempt to make adjustments or repairs while the
mower’s engine is running.
5.
Grass catcher components and the discharge cover are
subject to wear and damage which could expose moving
parts or allow objects to be thrown. For safety protection,
frequently check components and replace immediately
with original equipment manufacturer’s (O.E.M.) parts only,
listed in this manual. Use of parts which do not meet the
original equipment specifications may lead to improper
performance and compromise safety!
6.
Maintain or replace safety and instruction labels, as
necessary.
Do Not:
1.
Do not turn on slopes unless necessary; then, turn slowly
and gradually downhill, if possible.
2.
Do not mow near drop-offs, ditches or embankments. The
mower could suddenly turn over if a wheel is over the edge
of a cliff, ditch, or if an edge caves in.
3.
Do not try to stabilize the machine by putting your foot on
the ground.
4.
Do not use a grass catcher on steep slopes.
5.
Do not mow on wet grass. Reduced traction could cause
sliding.
Safety Symbols
This table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol
Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate
STOP
Turn off the engine before opening the bagger cover.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
4
Section 2 — Important Safe Operation Practices
(OK)
Figure 1
line
Slope Gauge
10° Slope
1
0
°
d
a
s
hed
USE THIS SLOPE GAUGE TO DETERMINE
IF A SLOPE IS TOO STEEP FOR SAFE OPERATION!
To check the slope, proceed as follows:
1. Remove this page and fold along the dashed line.
2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.)
3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ).
4. Adjust gauge up or down until the left corner touches the slope (See Figure 1 and Figure 2).
5. If there is a gap below the gauge, the slope is too steep for safe operation (See Figure 2 above).
(TOO STEEP)
Figure 2
10° Slope
WARNING! Slopes are a major factor related to tip-over and roll-over accidents which can result in severe injury or death.
Do not operate machine on slopes in excess of 10 degrees. All slopes require extra caution. If you cannot back up the slope
or if you feel uneasy on it, do not mow it. Always mow up and down slopes, never across the face of slopes.
5
Section 2 — Important Safe Operation Practices
3
Contents of Carton
Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below
and shown in Fig. 3-1. Three hardware packs are included in this kit and are detailed on the following page.
•
Vertical Support Bracket
•
Hitch Bracket Kit (5 Pcs.)
•
Bag Support Assembly
•
Chute Tube Extension
•
Bagger Counter-Weight
•
Discharge Chute Elbow
•
Blades (3 Pcs.)
•
Grass Catcher Cover
•
Chute Stop Bracket
•
Two Grass Bag Assemblies
•
Deck Baffle
•
Adhesive Foam Strip
•
Chute Discharge Plate
•
Upper Chute Tube
•
Three Hardware Packs (Detailed & illustrated on next page)
•
Upper Chute Support
•
Hinge Cover Pin
This bracket kit not needed
for installation on this unit.
Figure 3-1
6
CONTENTS OF HARDWARE PACK
This grass collector kit is shipped with three loose hardware packs enclosed and one set of hardware included in the mounting
bracket kit. Please check your hardware packs against the illustrations below. The quantities for each item is listed in parenthesis.
Section 3 — Contents of Carton
7
4
Assembly & Installation
NOTE: References to left, right, front and rear of the tractor are
from the operator’s position, unless otherwise stated.
•
Before assembly, place the tractor on a firm, level surface,
disengage the PTO, stop the tractor engine and set the
parking brake.
Assemble Mounting Brackets
To assemble the bagger mounting assembly, locate the
mounting assembly parts, as shown in Figure 4-1, and follow
these steps:
1.
Attach the two hitch side brackets to the rear attachment
bracket using four 710-0276 carriage bolts and 712-04063
flange lock nuts from hardware pack 689-00320. See Figure
4-1.
Figure 4-2
2.
Secure the mounting bracket assembly to the tractor using
two 911-0310 clevis pins and 914-04023 cotter pins from
hardware pack 689-00320. See Figure 4-3.
Figure 4-1
Note: When assembling this mounting assembly, it is best to
not fully tighten the bracket at this time. This will facilitate the
mounting process in later steps, which will then require fully
tightening this mounting assembly.
Mount Assembly on Tractor
Install mounting assembly on tractor as follows:
1.
8
Slide the mounting bracket assembly along the frame rails
of the tractor until the hooks in the mounting brackets
align under the shoulder bolts on your tractor, as seen in
Figure 4-2.
Figure 4-3
NOTE: When installing this mounting bracket assembly onto
the tractor, two mounting holes may be present, as shown in
the inset of Figure 4-3. Insert the clevis pins in whichever of
the mounting holes that line up on your specific tractor.
3.
Tighten all of the hardware installed at this time.
4.
Install the upright support bracket onto the mounting
assembly on the tractor by hooking it over the mounting
assembly as shown in (1) Figure 4-4.
5.
Secure the upright support bracket to the mounting
assembly in the mounting hole just right of the center hole,
as indicated in , with a 710-0376 hex bolt and 712-04063
flange lock nut from hardware pack 689-00320. See (2)
Figure 4-4
Assembling Remaining Bagger Components
Now that the mounting brackets are assembled and are in place
on the tractor, follow these steps to assemble the remaining
bagger components.
1.
1
Snap the plastic upper chute support in place by first
clipping the side portion onto the bagger support rail (1)
with the edge of the snap feature aligned with the line on
the label, as shown in the inset of Figure 4-6.
1
2
2
2
50-inch Deck
Figure 4-4
6.
Install and secure the hanger assembly onto the upright
support bracket (3 in ) using a 710-0276 carriage bolt and
712-04063 flange nut (4 in ) from hardware pack 68900320.
Figure 4-6
2.
Snap the front side of the chute support to the rail (2), as
shown in Figure 4-6.
3.
If not already installed by the factory, install the bagger
screen into the bagger cover by first inserting one end into
the corresponding cutout mounting hole, as in Figure 4-7.
Make sure to feed the screen under the lip, as in Figure 4-8.
3
4
4
Figure 4-5
Note: The carriage bolt (710-0276), from hardware pack
689-00320, goes in the top hole with the nut facing the
engine. The hex bolt (710-0376), from the same hardware
pack, goes in the bottom hole.
Figure 4-7
Section 4 — Assembly & Installation
9
4.
Clip in the other side of the screen by flexing the screen
and pushing it down into the other corresponding cutout
hole. See Figure 4-8.
Figure 4-10
Make sure screen sits under the cover’s lip
Figure 4-8
5.
Install the bagger cover onto the bag support assembly, as
seen in Figure 4-9. The plastic cover goes inside of the two
mounting tabs.
7.
Figure 4-11
Open Hood by pushing in on the rear, right-side tab with
your right hand, as seen in 1 of Figure 4-12, and lifting the
cover with your left hand in the center rear of the bagger
cover, 2.
Figure 4-9
6.
Slide the hinge pin into the hole located on the mounting
tab, as in Figure 4-10. Use the cut-out window (See inset in
Figure 4-10) to line up the hinge pin on the other side and
push pin all the way in until it reaches the end-stop. At this
point the pin clips into place and is secured by a tab in the
bagger cover. See Figure 4-11.
2
1
Figure 4-12
10
Section 4 — Assembly & Installation
8.
Install both bag assemblies onto the bag support brackets
by inserting the front edge in first, as seen in 1 of Figure
4-13, and setting the back edge down until it fits into the
assembly (2).
3.
Use a 15/16” wrench to remove the hex flange nut that secures
the blades to the blade spindle assemblies. See Figure 4-14.
WARNING: The hex flange nut has a right-handed
thread pattern. Do not attempt to force the nut in
wrong direction; it may damage the nut and create a
safety hazard.
4.
Place a new blade on each spindle so that side of the blade
with part number faces the ground when the mower is in
the operating position.
5.
Secure with the hex flange nut removed earlier. Use a
torque wrench to tighten the hex flange nut between 70 to
90 foot-pounds.
6.
Move the wood block to either the left or right blade for
stabilization and remove and replace the center blade so
that side of the blade with part number faces the ground
when the mower is in the operating position.
1
2
Installing the Deck Baffle
Note: If the deck is still flipped upside down with the blades
exposed, it may be easiest to flip the deck back over to complete the
following installation of the deck baffle and chute stop bracket.
Figure 4-13
Attaching Blades
WARNING! Always protect your hands while
servicing blades by wearing heavy work gloves or
using heavy rags.
1.
Remove two of the self-tapping deck screws on the front
right side of your deck.
2.
Install the deck baffle included with the loose parts to the
underside of the mowing deck using two 710-04666 hex
bolts and 912-3027 flange lock nuts from hardware pack
689-00329, as shown in Figure 4-15.
NOTE: Three high-lift bagging blades are included in the grasscatcher kit. Replace the blades with these new blades and save
the existing blades as replacements or to reinstall on the blade
spindles when not using the bagger kit.
1.
Remove cutting deck from beneath the tractor following
instructions for Deck Removal in operator’s manual of the
tractor. Gently flip the deck over to expose its underside.
2.
Place a block of wood between the center deck housing
baffle and the cutting blade to act as a stabilizer. See Figure
4-14.
Wood Block
Hex Flange Nut
Hex Bolt
Figure 4-15
Spindle Assembly
Figure 4-14
Section 4 — Assembly & Installation
11
Attaching Chute Stop Bracket
1.
Remove the carriage bolt and lock nut holding the chute
stop to the deck. See the left Inset of Figure 4-16. Retain the
carriage bolt for reinstallation.
Figure 4-16
2.
3.
Replace with new chute stop bracket, from the bagger
kit, at the same position on the deck. See the right Inset
of Figure 4-16. Secure with the carriage bolt previously
removed, and a 712-04065 flange lock nut from hardware
pack 689-00329.
NOTE: This chute stop bracket may stay on the unit even
when the bagger is not being used.
Installing the Chute Discharge Plate
1.
Remove the discharge chute by removing the two flange
lock nuts securing it.
2.
With a hammer, lightly tap the bolts out. Discard the bolts
and flange lock nuts.
Install the chute discharge plate to the bottom side of the
deck opening, as seen in Figure 4-17, using two carriage
bolts (710-3168) supplied in hardware pack 689-00329.
Figure 4-17
4.
Replace the discharge chute and secure with two flange
lock nuts (712-04065) included in the same hardware pack.
5.
Securely tighten the hardware.
Assembling the Discharge Chute
Before installing the discharge chute onto your tractor, some
components must first be assembled onto the chute. The
following are the instructions for assembling the discharge chute.
1.
Locate the chute elbow and install the grass-catcher pin
(911-04069) from hardware pack 689-00329 to the chute
elbow in the hole provided as shown in Figure 4-18. Secure
the grass-catcher pin with a flange lock nut (912-3027) from
the same hardware pack.
Figure 4-18
12
Section 4 — Assembly & Installation
2.
Attach the rubber strap (723-04009A), from hardware pack
689-00329, to the upper chute tube using the machine
screw (710-0924) from the same hardware pack. Secure
with a flange lock nut (912-3027) supplied in the same
hardware pack. See Figure 4-19.
Note: For the chute elbow to be properly installed, the bottom
edge must fall over the bottom of the deck opening and the tab
on top of the elbow should rest above the deck opening.
IMPORTANT: If the retainer clip is not present on the mowing deck, on
some units, one has been included with hardware pack 689-00329.
Attach the retainer hook (96606) with a self-tapping screw factory
installed in the deck in the position noted in Figure 4-21. Remove the
screw in the deck and reinstall with the retainer hook.
Retainer Clip
Figure 4-19
Installing the Discharge Chute
1.
Reinstall cutting deck onto the tractor reversing the instructions
for Deck Removal in operator’s manual of the tractor.
2.
Raise the deck to its highest position.
3.
Raise the chute deflector (A in Figure 4-21) on the deck and
hold it while you position the discharge chute over the
chute opening.
4.
Insert the hinge pin of the discharge chute into the tube on
the chute stop bracket. See B in Figure 4-21.
5.
Rotate the chute around the deck so that its front edge fits
snugly into the deck opening. Lower the chute deflector
slowly (C in Figure 4-21).
Figure 4-21
7.
Install the chute adapter onto the chute elbow by lining up
the tabs and sliding the adapter over the chute elbow, as
in Figure 4-22. Secure the chute adapter by installing the
two 726-3046 ratchet clips, included in hardware pack 68900329, into the holes provided.
A
C
B
Figure 4-22
Figure 4-20
6.
Attach the retainer strap on the discharge chute to the
retainer clip on the deck. Refer to Figure 4-21.
Section 4 — Assembly & Installation
13
8.
Peel the backing off of the self-adhesive foam strip
(721-04388) that has been included within your Carton of
Contents. Apply it to the upper chute tube, in the channel,
flush against the flange as shown in Figure 4-23.
Flange
Figure 4-24
Figure 4-23
9.
With the bagger cover open, install the upper chute over
the chute adapter, and rest the top so that the chute
support sits in the upper chute groove. See Figure 4-24.
Note: Make sure to align the upper chute with the ridges
on the bagger support bracket. With the bagger cover
open, install the upper chute over the chute adapter, and
rest the top so that the chute support sits in the upper
chute groove. See inset of Figure 4-24.
14
Section 4 — Assembly & Installation
10.
Secure the upper chute to the chute elbow by hooking the
rubber strap on the upper chute tube, to the pin previously
installed on the chute elbow.
11.
Close grass catcher cover.
12. Raise the deck back up into the desired cutting position.
Install The Counter Weight
RZT Models with a Fixed Front Axle
The front weight kit is designed for use with all RZT-L (Lap
Bar) Residential Zero-turn models. The front weight kit is NOT
designed nor required for use with all RZT-S (Steering Wheel)
Residential Zero-turn models.
1.
Attach the left mounting bracket and the right mounting
bracket to the weight bar using two 21⁄2-inch screws (7100859), and 3⁄8” flange nuts (712-04065) from hardware pack
689-00325. See Figure 4-26.
2.
Attach the weight bar assembly to the front axle with a 3
1⁄4-inch (710-3056) screw and (712-04063) flange nut from
hardware pack 689-00325 on the left side. Repeat on the
right side. Do not fully tighten at this time. See Figure 4-27.
WARNING: This front-weight kit is required when
operating any compatible lap bar RZT-L models
equipped with a grass collector. Failure to install this
kit may result in serious injury or death.
WARNING: Before beginning installation, place
the RZT-L on a firm and level surface, set the parking
brake, place the PTO in the disengaged (OFF)
position, stop the motor and remove the ignition
key to prevent unintended starting.
Note: The front weight kit is not utilized on the RZT-S (Steering
Wheel) Residential Zero Turn units. Do not attempt to mount it
on RZT-S models, as it will not fit.
RZT models are available with two different front-end styles.
Identify your RZT using the images in the following instructions
and follow the applicable steps.
RZT Models with a Pivoting Front Axle
Note: Having a second person assist you by holding the weight
bar in place will ease in completing the following steps.
1.
2.
Insert the two 3 1⁄4-inch (710-3056) screws from hardware
pack 689-00325, into the weight bar.
Figure 4-26
Position the weight bar onto the foot rest and secure it in
place with two 3⁄8” flange nuts (712-04065) from the same
hardware pack. See Figure 4-25.
Note: To hold and retain nut for tightening, it may
be necessary to insert the nut into the box end of a
combination wrench and slide up through the opening in
the floorboard.
Figure 4-27
3.
Figure 4-25
Visually center the weight bar assembly on the tractor
and tighten the hardware installed in step 2 to secure the
brackets to the front axle.
Section 4 — Assembly & Installation
15
5
Operation
Bagger Usage
NOTE: When both grass bags are full, place the tractor on a firm,
level surface, disengage the PTO, turn the tractor engine off and
set the parking brake.
1.
Pivot the seat forward.
2.
Open the grass catcher hood by pushing in on the rear,
right-side tab with your right hand, as seen in 1 of Figure
5-1, and lifting the cover with your left hand in the center
rear of the bagger cover, 2.
2
1
Figure 5-1
3.
Do not remove the chute tube assembly from the tractor.
4.
Remove the grass bags by lifting these up (1) and moving
the bags away from the bag support assembly (2). See
Figure 5-2.
2
1
Figure 5-2
16
5.
Empty the grass clippings at a proper disposal site, use the
handle at the bottom of each grass bag. Holding the bag
firmly, empty the contents
6.
Replace grass bags, close lid, flip down seat, restart your
tractor, release parking brake and resume cutting your
grass.
This page intentionally left blank.
19B70004OEM Parts List
2
16
7
12
24
12
5
15
24
4
34
8
7
15
30
13
17
23
9
33
31
11
12
28
5
3
19
10
12
22
23
6
26
12
21
20
39
25
18
38
40
32
34
36
34
1
37
35
23
29
18
27
14
Ref.
Part Number
Description
1.
631-04295A
Upper Chute Assembly
2.
931-04292
Twin Bagger Cover Assembly
3.
731-06497
Upper Chute Support
4.
731-06504
Bagger Cover Screen
5.
710-0276
Carriage Screw, 5/16-18 x 1.00”
6.
710-0376
Hex Head Screw, 5/16-18 x .75”
7.
911-0310
Clevis Pin, .50” Dia.
8.
964-04096A
Grass-bag Assembly
9.
683-04461A
Twin Bag Support Assembly
10.
683-04519A
Vertical Support Bracket
11.
711-04988
Cover Hinge Pin
12.
712-04063
Flange Lock Nut, 5/16-18
13.
735-0246A
End Plug
14.
631-04300C
Discharge Chute Elbow
15.
689-00204A
RZT Hitch Bracket Kit (RH & LH)
16.
783-06168-0637
Universal Cross Bracket
17.
710-04666
Hex Head Screw, 1/4 - 20 x .75
18.
703-09193
Weight Mount Bracket, RH
19.
703-09197
Weight Mount Bracket, LH
20.
719-04271A
Bagger Weight
21.
710-0859
Hex Head Screw, 3/8 - 16 x 2.50
22.
710-3056
Hex Head Screw, 5/16-18 x 3.25
23.
712-04065
Flange Lock Nut, 3/8 - 16
24.
914-04023
Cotter Pin, .080 x 1.5625 Internal
25.
726-3046
Ratchet Clip, .250
26.
731-06611
Bagger Chute Adapter, 8 x 13.5
27.
96606
Retainer Hook Bracket
28.
721-04388
Adhesive Strip
29.
683-0617A-0637
Chute Stop Bracket
30.
703-05783-0637
Deck Baffle, 50”
31.
710-3168
Carriage Bolt, 3/8-16 x 1.00
32.
742-04056C-0637
Bagging Blade, 17.90 Lg. Star
33.
783-06694-0637
Chute Discharge Plate
34.
912-3027
Flange Lock Nut, 1/4-20
35.
723-04009A
Chute Strap
36.
911-04069
Grass-catcher Pin
37.
710-0924
Machine Screw, 1/4-20
38.
710-3015
Hex Head Screw, 1/4-20 x .75
39.
712-04064
Flange Lock Nut, 1/4-20
40.
723-0476
Chute Strap
Parts List
19
MANUFACTURER’S LIMITED WARRANTY FOR
The limited warranty set forth below is given by MTD LLC with
respect to new merchandise purchased and used in the United
States and/or its territories and possessions, and by MTD Products
Limited with respect to new merchandise purchased and used
in Canada and/or its territories and possessions (either entity
respectively, “MTD”).
“MTD” warrants this product (excluding its Normal Wear Parts and
Attachments as described below) against defects in material and
workmanship for a period of one (1) year commencing on the date
of original purchase and will, at its option, repair or replace, free of
charge, any part found to be defective in materials or workmanship.
This limited warranty shall only apply if this product has been
operated and maintained in accordance with the Operator’s Manual
furnished with the product, and has not been subject to misuse,
abuse, commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of other
peril or natural disaster. Damage resulting from the installation or
use of any part, accessory or attachment not approved by MTD
for use with the product(s) covered by this manual will void your
warranty as to any resulting damage.
Normal Wear Parts are warranted to be free from defects in material
and workmanship for a period of thirty (30) days from the date of
purchase. Normal wear parts include, but are not limited to items
such as: batteries, belts, blades, blade adapters, tines, grass bags,
wheels, rider deck wheels, seats, snow thrower skid shoes, friction
wheels, shave plates, auger spiral rubber and tires.
Attachments — MTD warrants attachments for this product against
defects in material and workmanship for a period of one (1) year,
commencing on the date of the attachment’s original purchase or
lease. Attachments include, but are not limited to items such as:
grass collectors and mulch kits.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service dealer.
To locate the dealer in your area:
In the U.S.A.
Check your Yellow Pages, or contact MTD LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, or call 1-800-800-7310, 1-330-2204683 or log on to our Web site at www.mtdproducts.com.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
1-800-668-1238 or log on to our Web site at www.mtdcanada.com.
This limited warranty does not provide coverage in the following
cases:
a.
Log splitter pumps, valves, and cylinders have a separate
one- year warranty.
b.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior
finish due to use or exposure.
c.
Service completed by someone other than an authorized
service dealer.
d.
MTD does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and
their respective possessions and territories, except those sold
through MTD’s authorized channels of export distribution.
e.
Replacement parts that are not genuine MTD parts.
f.
Transportation charges and service calls.
g.
MTD does not warrant this product for commercial use.
No implied warranty, including any implied warranty of
merchantability or fitness for a particular purpose, applies
after the applicable period of express written warranty above
as to the parts as identified. No other express warranty,
whether written or oral, except as mentioned above, given
by any person or entity, including a dealer or retailer, with
respect to any product, shall bind MTD. During the period of
the warranty, the exclusive remedy is repair or replacement of
the product as set forth above.
The provisions as set forth in this warranty provide the sole
and exclusive remedy arising from the sale. MTD shall not
be liable for incidental or consequential loss or damage
including, without limitation, expenses incurred for substitute
or replacement lawn care services or for rental expenses to
temporarily replace a warranted product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply
to you.
In no event shall recovery of any kind be greater than the amount
of the purchase price of the product sold. Alteration of safety
features of the product shall void this warranty. You assume the
risk and liability for loss, damage, or injury to you and your property
and/or to others and their property arising out of the misuse or
inability to use the product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
IMPORTANT: Owner may be required to present proof of purchase
to obtain warranty coverage.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
GDOC-100167 REV. A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising