AXS-100 Slave Controller - Alarm International Systems

AXS-100 Slave Controller - Alarm International Systems
AXS-100 Slave Controller
For AXS-100 and AXS100XT Access Control Systems
Installation Guide
Introduction
The AXS-100 Slave Controller is a cost effective solution that
extends AXS-100 or AXS100XT access control system
functionality up to 16 doors on a single RS-485 data loop using
any combination of up to *8 ‘Master’ or ‘Slave’ controllers.
Each AXS-100 slave controller operates in real-time with
distributed intelligence and a full mirror database for offline
conditions. Should a communication failure occur between any of
the slaves and the master controller or between the master
controller and the host computer, each AXS-100 slave controller
will continue to function normally with no degradation in
performance and response times of card reading, alarm
activation or activation of logic events. Each AXS-100 slave can
also monitor the status of the protected doors (open or closed)
and the status of the door locks (locked or unlocked).
Initial system configuration is programmed via the master
controller’s keypad. Functionality such as event log access, card
holder programming and/or mode updates are handled via EIRIS
V4.6 (or higher) or AXSalert enterprise software.
*One ‘Master controller’ is required for each RS-485 data loop.
CAUTION: It is important that you read, understand, and
follow the instructions in this document. If you have
questions, call your local VT support representative.
1. Mounting and Initial Assembly
A.
Fig. 2 - Backup Battery
Metal Box Mounting
The AXS-100 Slave Controller must be installed indoors, within
the protected premise, in accordance with the National Electrical
Code (NFPA70) and the local authorities having jurisdiction.
Note: Do not connect (the transformer) to a power receptacle that
is controlled by a switch.
B. Backup Battery Installation (Optional)
Locate the optional backup battery (12V, 7.0Ah, Lead-acid
battery) in the lower left side of the system enclosure (see fig. 2).
Backup
battery
(optional)
Page 1 of 6
DE62821A_V7.0
C. Metal Box Door Lock Assembly
D. Tamper Switch Installation & Wiring
The door lock assembly of the system metal box is presented in
figure 3 (the lock and the brass nut are supplied in the system
accessories box).
It is necessary to protect the controller against tampering. A UL
Listed Tamper switch must be installed (see fig. 4) and wired to
AUXIN1 and COM of lock #3 of each controller.
2
1
Align lock with the prepunc he d hole and
insert it into the hole.
Place the brass nut on the
lock, tighten by hand and
finally tighten with
spanner (7/8”). Verify that
you can lock the door (key
rotation of 90 degrees).
Metal box
Metal box door
Figure 3 - Metal Cabinet Door Lock Assembly
Page 2 of 6
DE62821A_V7.0
Fig. 4 - Tamper Switch Installation
2. Panel Wiring
A. Proximity Readers
Each Slave Controller can be connected to two proximity readers:
Each reader is connected to the controller via a 4-wire cable.
The standard cable is color coded as follows:
• RED
Power +
• BLACK Power –
• GREENTX
• WHITE RX
Use extension cables with the same colors to avoid connection
errors.
Note 1: Installing a RDR-4 on a metal surface or a metal door
frame significantly decreases read range. If the reader must be
installed on a metal surface, use the RDR-BACK so that the
reader will be at least 1 cm (3/8 in.) away from the metal material
Page 3 of 6
DE62821A_V7.0
Note 2: When installing more than one RDR-4, the distance
between them should be at least 60 cm (2 ft.), to ensure proper
operation.
B. Inputs
Each AXS-100 Slave Controller can be connected to two inputs
per door as described below:
• Request-to-Exit (RTE) button or PIR: Installed near the
door in the secure area will allow a person to open the door
from within for leaving.
• Door Position micro switch: Installed between the door
and door frame will provide the controller with door status
indications.
Both the RTE and the Door Position inputs can be connected to
either normally open or normally closed switches. The default is a
normally open RTE and normally closed Door Position (when the
door is shut).
C. Locks
The AXS-100 Slave Controller can be connected to two electric
locks as described below:
Each slave controller can operate both electromagnetic strikes EMS (normally open) and electromagnetic locks - EML (normally
closed). Each connector block has a COMMON as well as N.O.
and N.C. connectors.
If the slave controller is configured for one door, connect it to the
EMS/EML, which is located on the left side of the controller.
All types of connections are detailed in the next drawing.
12VDC
Normally Open
NC
NC
COM
NO
----- Power+
Power+
Jumper
PWR
GND
12VDC
Normally Closed
----- Power+
COM
NO
Jumper
PWR
----- Power
GND
----- Power
Non-12VDC or
high current
devices - Dry
contact N.O.
Non-12VDC or
high current
devices - Dry
contact N.C.
NC
NC
------
COM
------
COM
------
NO
------
NO
PWR
PWR
GND
GND
The lock sections include also 12V power connectors. These
connectors provide power to the lock with a current limit of 400mA
for each lock. The slave controller supplies power from a backup
battery if available when the AC power is down. Electromagnetic
locks which constantly draw large currents should use the dry
contact ONLY without connecting the internal power supply. The
same holds true for any other device, which does NOT operate at
12VDC.
If you notice problems with a slave controller operating an EMS
that uses an internal power supply, connect the diode supplied
between + and – of the EMS output (see Panel Wiring Diagram).
D. Controller Configuration
Up to seven AXS-100 slave controllers can be connected to a
Master AXS-100/AXS-100 XT controller using a single twisted
pair cable. Each controller (irregardless of type) provides a
3-connector block for daisy chaining the devices in a bus type
configuration.
3. Maintenance
A.
Periodic Check
Once a month, the AXS-100 Slave Controller must be checked by
presenting a tag/card to the reader and verifying that the proper
door is opened
B.
Lithium Battery Handling/Disposal
Replace battery with PANASONIC Coin battery type CR2032, 3V
only. Use of another battery may present a risk of fire or
explosion.
Caution: Battery may explode if mistreated, do not recharge,
disassemble or dispose in fire. Dispose any used Lithium battery
only in an approved disposal container.
4. Specifications and Ordering Information
AXS-100 Slave Controller Specifications
Power Input
14 - 16.5 VAC, 50VA
Max. Current
2.5A
Memory Capacity
5,000 access card codes
Event Log
1,000 records per controller
Time Schedules
64 separate schedules
Each key may be assigned to 2 schedules
Dry Contact Relay
Max 1A continuous
Doors Controlled
Up to 2
Readers Controlled
Up to 2 external + 1 internal (for programming)
Slave Controllers per
Master
Up to 7
Inputs (x 2 doors)
Request-to-exit, door position
2 programmable inputs
Outputs
2 lock relays, NO/NC dry contact, 30 VDC 2A max.
1 auxiliary relay, NO/NC dry contact, 30V DC 2A max.
Output power for 2 locks: 10.3 - 12VDC, 400mA max.
2 readers output: 70 mA max.
Anti Passback
(APB) Modes
Local to each controller
Network APB
LED Status Indicators
Green LED #1: Output relay activated (Door 1)
Red LED #2: Power ON
Green LED #3: Ext. battery charged
Red LED #4: Alarm relay activated
Green LED #5: Output relay activated (Door 2)
Construction
Metal (indoor usage only)
Connect terminal B to B and D to D, GND to GND, this way up to
seven slave controllers.
Color
White
Weight
3.8 kilos (8.4 lbs) approximate
Each AXS-100 Slave Controller has to be assigned a unique ID
address before the device can be fully functional. Since each
RS-485 data loop MUST contain a Master Controller whose ID
address is always set to 1, the ID addresses of the slave(s) units
are range from 2…….8. Addresses
Operating Temperature
& Humidity
0° to 50°C (32° to 122°F);
05% to 80% non-condensing
Storage Temperature
-20 to +70°C (-4 to 158°F)
Dimensions (L x W x D)
315 x 262 x 74mm (12-3/8 x 10-5/16 x 10-15/16 in.)
Maximum Cable Length
from Controller
5.0 meters (16.4 feet)
Compatible Software
EIRIS V4.6 or higher
AXSalert (all versions)
Standards Compliance
Part 15 of the FCC Rules
RSS-210 of Industry and Science Canada
Warranty
One year limited warranty (excluding batter)
The ID address of the slave controller is configured using the DIP
switches located on the controllers’ circuit board as shown below:
NOTE: A controller’s
ID address MUST be
set before applying
power to the unit.
Also never change the
DIP switch settings
while the slave is
powered up.
NOTE: The ID addresses of the slave controllers need not be in
the physical order of connection.
E. Power Connection
Connect the AC power cable to the power connector on the top
right side of the board.
F.
Backup Battery Connection
Connect backup battery to black and red wires on the left side.
Page 4 of 6
DE62821A_V7.0
Ordering Details
AXS-100 Slave Controller
5-100613
AXS-100 Slave Controller
Compatible System Readers
3-6304-0
RDR-4, Proximity Reader
3-6321-0
RDK-4, Proximity Reader with Keypad
3-6309-0
RDM-4, Proximity Reader, Mullion type
3-6304-1
RDR-4B, Proximity Reader, 12V / 50mA output
3-6304-2
RDR-4B/W, Proximity Reader, White, 12V / 50mA output
5. Controller Configuration
An AXS-100 Master-Slave system can control up to 16 doors on a single RS-485 data loop using any combination of up to
8 master or slave controllers.
NOTE: One master controller is required for each RS-485 data loop.
Connections between the controllers must be implemented with CAT-5 twisted pair cable. The maximum distance between
controller #1 (Master) and the furthest one (controller #8) is no longer than 1,200 meters.
The circuit board of the AXS-100 controller (irregardless of type) contain 3-connector blocks for daisy chaining up to 7 (seven)
slave controllers to one Master AXS-100/AXS-100 XT controller in a bus configuration. Connect terminal B to B and D to D,
GND to GND, this way up to seven slave controllers.
Page 5 of 6
DE62821A_V7.0
6. Standards Compliance
This device complies with the essential requirements and
provisions of Directive 1999/5/EC of the European Parliament
and of the Council of 9 March 1999 on radio and
telecommunications terminal equipment.
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in residential
installations. This equipment generates; uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio and television reception. However, there is
no guarantee that interference will not occur in a particular
installation. If this device does cause such interference, which
can be verified by turning the device off and on, the user is
encouraged to eliminate the interference by one or more of the
following measures:

Re-orient or re-locate the receiving antenna.

Increase the distance between the device and the receiver.

Connect the device to an outlet on a circuit different from
the one which supplies power to the receiver.

Consult the dealer or an experienced radio/TV technician.
7. Product Warranty
Visonic Technologies Ltd. (VT or the Company), and its affiliates,
warrants its products (hereinafter referred to as "the Product”) to be
free of defects in materials and workmanship under normal operating
conditions and use for a period of one year from the date of shipment
by VT. The Company’s obligations shall be limited within the warranty
period, at its option, to repair or to replace the defective Product or any
defective component or part thereof. To exercise this warranty, the
product must be returned to the manufacturer freight prepaid and
insured.
This warranty does not apply to repairs or replacement caused by
improper installation, Product misuse, failure to follow installation or
operating instructions, alteration, abuse, accident, tampering, repair by
anyone other than VT, external causes, and failure to perform required
preventive maintenance. This warranty also does not apply to any
products, accessories, or attachments used in conjunction with the
Product, including batteries, which shall be covered solely by their own
warranties, if any. VT shall not be liable for any damage or loss
whatsoever, whether directly, indirectly, incidentally, consequentially or
otherwise, resulting from a malfunction of the Product due to products,
accessories, or attachments of others, including batteries, used in
conjunction with the Product.
VT MAKES NO EXPRESS WARRANTIES EXCEPT THOSE STATED
IN THIS STATEMENT. VT DISCLAIMS ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. VT’S SOLE RESPONSIBILITY FOR
WARRANTY CLAIMS IS LIMITED TO REPAIR OR TO REPLACE AS
SET FORTH IN THIS STATEMENT.
VT shall have no liability for any death, personal injury, property
damage, or other loss whether direct, indirect, incidental,
consequential, or otherwise, based on a claim that the Product failed to
function. However, if VT is held liable, whether directly or indirectly, for
any loss or damage arising under this limited warranty or otherwise,
regardless of cause or origin, VT's maximum liability shall be limited to
the purchase price of the Product, which shall be fixed as liquidated
damages and not as a penalty, and shall be the complete and
exclusive liability of VT.
VT shall not, under any circumstances whatsoever, be liable for any
inaccuracy, error of judgment, default, or negligence of VT, its
employees, officers, agents, or any other party, or of the purchaser or
user, arising from any assistance or communication of any kind
regarding the configuration, design, installation, or creation of security
system involving the Product, that being the responsibility of the
purchaser or user.
If VT is unable to make such repair or replacement, VT’s entire liability
shall be limited to the cost of a reasonable substitute product. VT shall
not be responsible for any dismantling, installation, reinstallation,
purchasing, shipping, insurance, or any similar charges.
VT shall have no liability for any damages, including without limitation,
any direct, indirect, incidental, special, or consequential damages,
expenses, costs, profits, lost savings or earnings, or other damages
arising out of the use of the Product or the removal, installation,
reinstallation, repair or replacement of the Product or any related
events. In the event that there is any liability against VT, such liability
shall be limited to the purchase price of the Product which amount shall
be fixed as liquidated damages.
The purchaser and user understand that this Product may be
compromised or circumvented by intentional acts; that the Product will
not in all cases prevent death, personal injury, property damage, or
other loss resulting from burglary, robbery, fire or other causes; and
that the Product will not in all cases provide adequate warning or
protection. The purchaser and user also understand that a properly
installed and maintained alarm may reduce the risk of events such as
burglary, robbery, and fire without warning, but it is not insurance or a
guarantee that such events will not occur or that there will be no death,
personal injury, property damage, or other loss as a result of such
events.
By purchasing the Product, the purchaser and user shall defend,
indemnify and hold VT, its officers, directors, affiliates, subsidiaries,
agents, servants, employees, and authorized representatives harmless
from and against any and all claims, suits, costs, damages, and
judgments incurred, claimed, or sustained whether for death, personal
injury, property damage, or otherwise, because of or in any way related
to the configuration, design, installation, or creation of a security
system involving the Product, and the use, sale, distribution, and
installation of the Product, including payment of any and all attorney’s
fees, costs, and expenses incurred as a result of any such events.
The purchaser or user should follow the Product installation and
operation instructions and test the Product and the entire system at
least once each week. For various reasons, including but not limited to
changes in environmental conditions, electric, electronic, or
electromagnetic disruptions, and tampering, the Product may not
perform as expected. The purchaser and user are advised to take all
necessary precautions for the protection and safety of persons and
property.
This statement provides certain legal rights. Other rights may vary
by state or country. Under certain circumstances, some states or
countries may not allow exclusion or limitation of incidental or
consequential damages or implied warranties, so the above exclusions
may not apply under those circumstances and in those states or
countries.
VT reserves the right to modify this statement at any time, in its sole
discretion without notice to any purchaser or user. However, this
statement shall not be modified or varied except by VT in writing, and
VT does not authorize any single individual to act on its behalf to
modify or vary this statement.
Any questions about this statement should be directed to VT. 3/0
VT World Headquarters * Tel Aviv, Israel * Tel: + 972 3 768-1400 * support@visonictech.com
VT Americas
* Bloomfield, CT (USA) * Tel: 1-800-223-0020 * vta_support@visonictech.com
VT United Kingdom * Beckenham Kent BR3 90BF, U.K. * Tel: + 44-870-730-0840 * vtuk_support@ visonictech.com
Visonic GmbH * D-40215 Düsseldorf, Germany * Tel: + 49-0-211-600-696-0 * support@ visonictech.de
Additional information may be found at www.VT-Partners.com
Page 6 of 6
DE62821A_V7.0 MAY 07
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased
it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your
supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.
Manufactured In Israel
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising