APC SUA2200XL-NETPKG uninterruptible power supply (UPS) User manual

User Manual

APC Smart-UPS

®

XL

2200/3000 VA XL

120/208/230 VAC

Tower/Rack-Mount 5U

Uninterruptible Power Supply

English

990-2975 09/2006

Introduction

About this UPS

The American Power Conversion (APC®) Uninterruptible Power Supply (UPS) provides protection for electronic equipment from utility power blackouts, brownouts, sags and surges. The UPS filters small utility line fluctuations and isolates electronic equipment from large disturbances by internally disconnecting from utility line power. The UPS provides continuous power from the internal battery until utility power returns to safe levels or the battery is fully discharged.

Unpack

Read the Safety Guide before installing the UPS.

Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage.

The packaging is recyclable; save it for reuse or dispose of it properly.

Check the package contents:

•UPS

•Front bezel

•Literature kit containing:

– EPO connector

– Serial cable

– USB cable

– Eight ornamental screws for securing the unit in the rack

– Eight 5/16 in (.8 cm) pan-head screws for attaching cleats to the chassis rails

(required for four post rack only)

– Eight 5/8 in (1.6 cm) pan-head screws for attaching rack-mount brackets to the unit

– Eight snap-on speed nuts

– Two rail cleats (required for four post rack only)

– Two rack-mount brackets

– Product documentation

– Smart-UPS® User Manuals CD

– PowerChute® Business Edition CD

– Safety information

– Warranty information

Additional contents for

230 V models:

– APC power cable

– Alternate input power cord

(UK customers)

– IEC Power cord

– IEC jumper cables

Specifications

Temperature

Operating

Storage

Maximum

Elevation

Operating

Storage

32 ° to 104 ° F (0 ° to 40 ° C)

5 ° to 86 ° F (-15 ° to 30 ° C) charge the UPS battery every six months

86 ° to 113 ° F (30 ° to 45 ° C) charge the UPS battery every three months

10,000 ft (3,000 m)

50,000 ft (15,240 m)

This unit is intended for indoor use only. Select a location sturdy enough to handle the weight.

Do not operate the UPS where there is excessive dust or the temperature or humidity are outside the specified limits.

Environmental factors impact battery life. High temperatures, poor utility power, and frequent, short duration discharges will shorten battery life.

0 to 95% relative humidity, non-condensing Humidity

Weight 142 lbs (64 kg) with battery module

89 lbs (40 kg) without battery module

27 lbs (12 kg) each battery module

Maximum Number of External Battery Packs Supported by the

Smart-UPS XL

142 lbs (64 kg)

10

NOTE: The model and serial numbers are located on a small, rear panel label. For some models, an additional label is located on the chassis under the front bezel.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 3

Installation

The UPS is shipped in tower configuration.

Tower Configuration

Connect the battery.

After the battery has been connected, tuck the battery cables in between the battery and the battery door. This will ensure a secure fit of the bezel to the unit.

4 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Rack-Mount Configuration

This unit is intended for mounting in a two post rack. To order a four post rack-mount kit contact your dealer or refer to the APC Web site, www.apc.com.

Tower to rack-mount conversion procedure

The UPS and the battery modules are heavy. Remove the battery modules to lighten the UPS during installation.

Pull the battery disconnect strap attached to the battery connector. DO NOT pull the battery cables to disconnect the battery. Disconnect

Battery

Battery

Disconnect

Strap

Remove the top cover and .

Remove and rotate the display panel .

Foam

Spacer

Four post rack-mount bracket position

Two post rack-mount bracket position x4

5/8 in

1.6 cm

A four post rack configuration requires installation of two brackets in the forward position (see diagram above), two cleats (supplied with this unit), and the four post rails. The rails can be ordered through the

APC Web site www.apc.com.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 5

Install unit in rack

Ensure rack stability prior to installing devices in the rack.

The UPS should be installed at or near the bottom of the rack. If external battery packs are to be installed in the rack, the UPS must be the top unit in the configuration.

Connect

Battery x4

Ornamental

Foam Spacer

After all of the batteries have been connected, tuck the battery cables in between the batteries and the battery doors. This will ensure a secure fit of the bezel to the unit.

Accessories

This UPS is equipped with an accessory SmartSlot. Refer to the APC Web site, www.apc.com for available accessories.

If a standard accessory, such as a Network Management card is to be installed on this UPS, refer to the Utility

CD for user documentation.

Install accessories prior to connecting power to the UPS.

6 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Start-Up

Connect Equipment and Power to the UPS

1. The UPS features a transient voltage surge-suppression (TVSS) screw located on the rear panel, for connecting the ground lead on surge suppression devices such as telephone and network line protectors.

Prior to connecting the grounding cable, ensure that the UPS is NOT connected to utility or battery power.

2. Connect equipment to the UPS.

NOTE: This UPS is equipped with an external battery connector on the rear panel of the unit.

Where appropriate use an APC extension battery cable. For ordering details contact your dealer or APC through the Web site www.apc.com.

3. Add optional accessories to the SmartSlot located on the rear panel.

4. Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords.

– 230 V models: The utility power cord is supplied in the UPS literature kit. Prior to connecting the utility power, connect the ground lead (optional) to the TVSS screw.

5. 120 V models: Check the SITE WIRING FAULT LED located on the rear panel. The LED will be illuminated if the UPS is plugged into an improperly wired utility power outlet, (see Troubleshooting).

6. To use the UPS as a master on/off switch be sure all connected equipment is switched on.

Rear Panels

3000 VA 3000 VA

120 VAC 208 VAC

2200 VA

120 VAC

2200 VA

3000 VA

230 VAC

Start the UPS

1. Press the button on the front panel to start the UPS.

– The battery charges to 90% capacity during the first four hours of normal operation. Do not expect full battery run capability during this initial charge period.

– Refer to the APC Web site, www.apc.com for battery runtimes.

2. For optimal computer system security, install PowerChute Smart-UPS monitoring software.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 7

Communication Ports

SERIAL PORT USB PORT Use only the supplied cable to connect to the serial port. A standard serial interface cable is incompatible with the UPS.

Serial and USB ports cannot be used simultaneously.

Emergency Power Off

The emergency power off (EPO) feature is user configurable. EPO provides immediate de-energizing of connected equipment from a remote location, without switching to battery operation.

1. Use the EPO connector supplied with the UPS.

2. Use a normally-open contact to connect the +24 terminal to the IN terminal. External voltage is not required.

3. Wire the four-pin connector to the EPO system.

EPO PORT

(located on rear panel)

EPO

Connector

The EPO interface is a Safety Extra Low Voltage (SELV) circuit. Connect it only to other SELV circuits.

The EPO interface monitors circuits that have no determined voltage potential. Such closure circuits may be provided by a switch or relay properly isolated from the utility. To avoid damage to the UPS, do not connect the EPO interface to any circuit other than a closure type circuit.

Use one of the following cable types to connect the UPS to the EPO switch.

• CL2: Class 2 cable for general use.

• CL2P: Plenum cable for use in ducts, plenums, and other spaces used for environmental air.

• CL2R: Riser cable for use in a vertical run in a floor-to-floor shaft.

• CLEX: Limited use cable for use in dwellings and for use in raceways.

• For installation in Canada: Use only CSA certified, type ELC, (extra-low voltage control cable).

• For installation in other countries: Use standard low-voltage cable in accordance with national and local regulations.

8 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Operation

Display Panels

120/208 V models

230 V models

120/208 V

Battery

Charge

230 V

Display Panel Indicators and Function Buttons

Indicator

LED

Indicator Title

On Line

AVR Trim

AVR Boost

On Battery

Description

The UPS is supplying utility power to the connected equipment,

(see Troubleshooting).

The UPS is compensating for a high utility voltage. Refer to the APC Web site, www.apc.com for AVR settings.

The UPS is compensating for a low utility voltage. Refer to the APC Web site, www.apc.com for AVR settings.

The UPS is supplying battery power to the connected equipment.

Overload The connected equipment is drawing more than the UPS power rating allows,

(see Troubleshooting).

Replace Battery/Battery

Disconnected

The battery is disconnected or must be replaced, (see Troubleshooting).

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 9

Indicator

LED

120 V

Indicator Title

208 V

Diagnostic

Utility Voltage

Description

The UPS has a diagnostic feature that indicates the utility voltage.

The UPS starts a self-test as part of this procedure. The self-test does not affect the voltage display.

Battery

Charge

230 V

Battery

Charge

Press and hold the button to view the utility voltage bar graph indicator.

After a few seconds, this five-LED Battery Charge the display panel will show the utility input voltage.

indicator on the right of

Refer to the figure on the left for the voltage reading.

Values are not listed on the UPS.

The indicator on the UPS shows the voltage is between the displayed value on the list and the next higher value, (see Troubleshooting).

Feature

Button

Feature Title

Power On

Self-Test

Cold Start

Power Off

Function

Press this button to turn on the UPS. Continue reading for additional capabilities.

Automatic: The UPS performs a self-test automatically when tuned on, and every two weeks thereafter (by default). During the self-test, the UPS briefly operates the connected equipment on battery.

Manual: Press and hold the self-test.

button for a few seconds to initiate the

When there is no utility power and the UPS is off, the cold start feature will switch the UPS and connected equipment onto battery power,

(see Troubleshooting).

Press this button to turn off the UPS.

10 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Configuration

UPS settings

Settings are adjusted through PowerChute software or optional SmartSlot accessory cards.

Function

Factory

Default

User Selectable

Choices Description

Automatic

Self-Test

On startup and every 14 days

(336 hours) there after

• On startup and every

7 days (168 hours) there after

• On startup and every

14 days (336 hours) there after

• On startup only

• No self-test

Up to eight characters

(alphanumeric) mm/dd/yy

Set the interval at which the UPS will execute a self-test.

UPS ID

Date of Last

Battery

Replacement

Minimum Capacity

Before Return from

Shutdown

Shutdown Delay

UPS_IDEN

Manufacture

Date

0 percent

Voltage Sensitivity

The UPS detects and reacts to line voltage distortions by transferring to battery operation to protect the connected equipment.

Alarm Delay

Control

High sensitivity

Enable

90 seconds

Uniquely identify the UPS, (i.e. server name or location) for network management purposes.

Reset this date when you replace the battery module.

• 0%

• 15%

• 30%

• 45%

• 60%

• 75%

• 90%

Brightly illuminated: high sensitivity

Dimly illuminated: medium sensitivity

No illumination: low sensitivity

Specify the percentage to which batteries will be charged following a low battery shutdown before powering connected equipment.

Adjust by pressing the VOLTAGE SENSITIVIY switch (rear panel). Use a pointed object, (such as a pen) to do so.

Note: In situations of poor power quality, the

UPS may frequently transfer to battery operation. If the connected equipment can operate normally under such conditions, reduce the sensitivity setting to conserve battery capacity and service life.

Mute ongoing alarms or disable all alarms.

• Enable

• Mute

• Disable

• 0 s

• 90 s

• 180 s

• 270 s

• 360 s

• 450 s

• 540 s

• 630 s

Set the interval between the time when the UPS receives a shutdown command and actual shutdown.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 11

12

Function

Factory

Default

User Selectable

Choices Description

Low Battery

Warning

PowerChute software interface provides automatic, unattended shutdown when approximately two minutes of battery operated run time remains.

2 minutes

LED is located on rear panel

Synchronized

Turn-on Delay

High Transfer Point

0 seconds

208 V models:

225 VAC

120 V models:

127 VAC

Brightly

illuminated: low battery warning level of about 2 minutes

Dimly illuminated: low battery warning level of about

5 minutes

No illumination: low battery warning level is about 8 minutes

• 0 s

• 60 s

• 120 s

• 180 s

• 225 VAC

• 229 VAC

• 240 s

• 300 s

• 360 s

• 420 s

• 233 VAC

• 237 VAC

The low-battery warning beeps are continuous when two minutes of run time remain.

To change the default interval setting, use a pointed object such as a pen to press the

VOLTAGE SENSITIVIY switch (rear panel), while pressing the button, (front display).

Change the low battery warning interval setting to the time that the operating system or system software requires to safely shut down.

Specify the time the UPS will wait after the return of utility power before start up, (to avoid branch circuit overload).

To avoid unnecessary use of the battery where utility voltage is chronically high, set the high transfer point higher if the connected equipment can tolerate this condition.

• 127 VAC

• 130 VAC

• 133 VAC

• 136 VAC

230 V models:

253 VAC

Low Transfer Point 120 V models:

106 VAC

208 V models:

182 VAC

• 253 VAC

• 257 VAC

• 97 VAC

• 100 VAC

• 261 VAC

• 265 VAC

• 103 VAC

• 106 VAC

• 182 VAC

• 178 VAC

• 174 VAC

• 170 VAC

To avoid unnecessary use of the battery where utility voltage is chronically low, set the low transfer point lower if the connected equipment can tolerate this condition.

230 V models:

208 VAC

Output Voltage

230 V models 230 VAC

• 196 VAC

• 200 VAC

• 204 VAC

• 208 VAC

• 220 VAC

• 230 VAC

• 240 VAC

Set the output voltage of the UPS.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Troubleshooting

Use this chart to solve minor UPS installation and operation problems. Refer to www.apc.com for assistance with complex UPS problems.

Solution Problem and/or Possible Cause

UPS will not turn on

The battery is not connected properly.

Check that the battery connector is fully engaged.

button not pushed.

The UPS is not connected to utility power supply.

Very low or no utility voltage

Press the button once to power-up the UPS and connected equipment.

Check that the power cable from the UPS to the utility power supply is securely connected at both ends.

Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, have the utility voltage checked.

UPS will not turn off

The UPS is experiencing an internal fault

UPS beeps occasionally

Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately.

Normal UPS operation when running on battery.

None: The UPS is protecting the connected equipment. Press the to silence this alarm.

UPS is not providing expected backup time

button

The UPS battery(s) are weak due to a recent power outage or battery(s) are near the end of their service life.

Charge the battery(s). Batteries require recharging after extended outages.

Batteries can wear faster when put into service often or when operated at elevated temperatures. If the battery(s) are near the end of their service life, consider replacing the battery(s) even if the replace battery LED is not yet illuminated.

All LEDs are illuminated and the UPS emits a constant beeping

The UPS is experiencing an internal fault.

Front panel LEDs flash sequentially

Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately.

The UPS has been shut down remotely through software or an optional accessory card.

None: The UPS will restart automatically when utility power returns.

All LEDs are off and the UPS is plugged into a wall outlet

The UPS is shut down or the battery is discharged from an extended outage.

None: The UPS will restart automatically when utility power is restored and the battery has a sufficient charge.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 13

14

Problem and/or Possible Cause Solution

The Overload LED is illuminated and the UPS emits a sustained alarm tone

The UPS is overloaded.

The connected equipment exceeds the specified “maximum load” as defined in Specifications on the APC Web site, www.apc.com.

The alarm remains on until the overload is removed. Disconnect nonessential equipment from the UPS to eliminate the overload condition.

The UPS continues to supply power as long as it is online and the circuit breaker does not trip; the UPS will not provide power from batteries in the event of a utility voltage interruption.

The Replace Battery/Battery Disconnected LED is illuminated

The Replace Battery/Battery

Disconnected LED flashes and a short beep is emitted every two seconds to indicate the battery is disconnected.

Weak battery

Check that the battery connectors are fully engaged.

Failure of a battery self-test: Replace

Battery/Battery Disconnected LED illuminates and the UPS emits short beeps for one minute. The UPS repeats the alarm every five hours.

Allow the battery to recharge for 24 hours and perform a self-test. If the problem persists after recharging, replace the battery.

Allow the battery to recharge for 24 hours. Perform the self-test procedure to confirm the replace battery condition. The alarm stops and the LED clears if the battery passes the self-test.

If the battery fails again, it must be replaced. The connected equipment is unaffected.

The Site Wiring Fault LED on the rear panel is illuminated (120 V model only)

The UPS is plugged into an improperly wired utility power outlet.

Wiring faults detected include missing ground, hot-neutral polarity reversal, and overloaded neutral circuit.

Contact a qualified electrician to correct the building wiring.

The input circuit breaker trips

The connected equipment exceeds the specified “maximum load” as defined in Specifications on the APC Web site, www.apc.com.

Unplug all nonessential equipment from the UPS.

Reset the circuit breaker.

The AVR Boost or AVR Trim LEDs are illuminated

The system is experiencing very high or low utility voltage.

Have a qualified service personnel check your facility for electrical problems. If the problem persists, contact the utility company for further assistance.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Problem and/or Possible Cause Solution

There is no utility power

There is no utility power and the UPS is off.

Use the cold start feature to supply power to the connected equipment front the UPS battery(s).

Press and hold the button. There will be a short beep followed by a longer beep. Release the button during the second beep.

UPS operates on battery although line voltage exists

The UPS input circuit breaker trips.

Your system is experiencing very high, low or distorted line voltage.

Unplug all nonessential equipment from the UPS.

Reset the circuit breaker.

Move the UPS to a different outlet on a different circuit: Inexpensive fuel powered generators may distort the voltage. Test the input voltage with the utility voltage display, (see Operation). If acceptable to the connected equipment, reduce the UPS sensitivity.

Battery Charge and Load LEDs flash simultaneously

The UPS has shut down.

The internal temperature of the UPS has exceeded the allowable threshold for safe operation.

Check that the room temperature is within the specified limits for operation.

Check that the UPS is properly installed, allowing for adequate ventilation.

Allow the UPS to cool down. Restart the UPS. If the problem persists, contact APC at www.apc.com.

Diagnostic utility voltage

All five LEDs are illuminated.

There is no LED illumination.

The line voltage is extremely high and should be checked by an electrician.

The line voltage is extremely low and should be checked by an electrician.

On Line LED

There is no LED illumination.

The LED is blinking.

The UPS is running on battery, or it must be turned on.

The UPS is running an internal self-test.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 15

Maintenance, Transport, and Service

Replacing the Battery Module

This UPS has easy-to-replace, hot-swappable battery modules. Replacement is a safe procedure, isolated from electrical hazards. You may leave the UPS and connected equipment on during the replacement procedure.

Once the batteries are disconnected the connected equipment is not protected from power outages.

Refer to the appropriate replacement battery user manual for battery module installation instructions. See your dealer or contact APC at www.apc.com for information on replacement battery modules.

Be sure to deliver the spent battery(s) to a recycling facility or ship it to APC in the replacement battery packing material.

Service

If the UPS requires service do not return it to the dealer. Follow these steps:

1. Review the problems discussed in Troubleshooting to eliminate common problems.

2. If the problem persists, contact APC Customer Support through the

APC Web site, www.apc.com.

– Note the model number of the UPS, the serial number located on the back of the unit, and the date purchased. If you call APC Customer Support, a technician will ask you to describe the problem and attempt to solve it over the phone. If this is not possible, the technician will issue a Returned

Material Authorization Number (RMA#).

– If the UPS is under warranty, repairs are free.

– Procedures for servicing or returning products may vary internationally. Refer to the APC Web site for country specific instructions.

3. Pack the UPS in its original packaging. If this is not available, refer to www.apc.com for information about obtaining a new set.

– Pack the UPS properly to avoid damage in transit. Never use Styrofoam beads for packaging.

Damage sustained in transit is not covered under warranty.

– Always DISCONNECT THE UPS BATTERY before shipping in compliance with U.S.

Department of Transportation (DOT) and IATA regulations. The battery may remain in the

UPS.

4. Mark the RMA# on the outside of the package.

5. Return the UPS by insured, prepaid carrier to the address given to you by Customer Support.

16 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Two-Year Warranty

The limited warranty provided by American Power Conversion (APC®) in this statement of Limited Factory Warranty applies only to products you purchase for your commercial or industrial use in the ordinary course of your business.

Terms of warranty

APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. The obligation of APC under this warranty is limited to repairing or replacing, at its sole discretion, any such defective products. This warranty does not apply to equipment that has been damaged by accident, negligence or misapplication or has been altered or modified in any way.

Repair or replacement of a defective product or part thereof does not extend the original warranty period. Any parts furnished under this warranty may be new or factory-remanufactured.

Non-transferable warranty

This warranty extends only to the original purchaser who must have properly registered the product. The product may be registered at the

APC Web site, www.apc.com.

Exclusions

APC shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product does not exist or was caused by end user or any third person misuse, negligence, improper installation or testing. Further, APC shall not be liable under the warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage or connection, inappropriate on-site operation conditions, corrosive atmosphere, repair, installation, start-up by non-APC designated personnel, a change in location or operating use, exposure to the elements, Acts of God, fire, theft, or installation contrary to APC recommendations or specifications or in any event if the APC serial number has been altered, defaced, or removed, or any other cause beyond the range of the intended use.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, OF PRODUCTS SOLD,

SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH. APC DISCLAIMS ALL IMPLIED

WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE. APC EXPRESS

WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL

ARISE OUT OF, APC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE

PRODUCTS. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER

WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC SOLE LIABILITY AND

PURCHASER EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. APC WARRANTIES EXTEND ONLY TO

PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES.

IN NO EVENT SHALL APC, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF

INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE OR

INSTALLATION, OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF

FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY

OF SUCH DAMAGES. SPECIFICALLY, APC IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE, LOSS

OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUENTS, CLAIMS

BY THIRD PARTIES, OR OTHERWISE.

NO SALESMAN, EMPLOYEE OR AGENT OF APC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY.

WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY IN WRITING SIGNED BY AN APC OFFICER AND LEGAL

DEPARTMENT.

Warranty claims

Customers with warranty claims issues may access the APC customer support network through the Support page of the APC Web site, www.apc.com/support. Select your country from the country selection pull-down menu. Open the Support tab at the top of the Web page to obtain contact information for customer support in your region.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 17

Regulatory Information

Regulatory Agency Approvals and Radio Frequency Warnings

FCC Compliance Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense.

120/208 V models

LISTED 42C2

E95463

230 V models geprüfte

Sich erh eit N 394

APC Worldwide Customer Support

Customer support for this or any other APC product is available at no charge in any of the following ways:

• Refer to the APC Web site to access documents in the APC Knowledge Base and to submit customer support requests.

– www.apc.com (Corporate Headquarters)

Connect to localized APC Web sites for specific countries, each of which provides customer support information.

– www.apc.com/support/

Global support searching APC Knowledge Base and using e-support.

• Contact an APC Customer Support center by telephone or e-mail.

Local, country-specific centers: go to www.apc.com/support/contact for information.

Contact the APC representative or other distributor from whom you purchased your APC product for information on how to obtain local customer support.

Entire contents copyright 2006 American Power Conversion Corporation. All rights reserved. Reproduction in whole or in part without permission is prohibited.

APC, the APC logo, Smart-UPS and PowerChute are trademarks of American Power Conversion Corporation. All other trademarks, product names, and corporate names are the property of their respective owners and are used for informational purposes only.

18 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Date of product declaration

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 19