MAXPRO VMS R300 Viewer Edition Commissioning and Installation

MAXPRO VMS R300 Viewer Edition Commissioning and Installation
MAXPRO® VMS R300 Viewer Edition
Commissioning and Installation Guide
Document 800-11111 – Rev A – 02/2012
Revisions
Issue
Date
Description
1.0
February 24, 2012
New document
MAXPRO VMS R300 VIEWER EDITION
Table of Contents
Table of Contents
ABOUT THIS GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INTRODUCING MAXPRO® VMS R300 VIEWER EDITION . . . . . . . . . . . . . . . . . . . . . . . .3
SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
INTENDED AUDIENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
INSTALLATION AND COMMISSIONING GUIDE STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . .4
TYPOGRAPHICAL CONVENTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
COMMISSIONING PLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
STEPS IN THE COMMISSIONING PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SETTING UP THE MAXPRO VMS SERVER AND CLIENT COMPUTERS . . . . . . . . . . . . . . . . . . . 5
INSTALLING THE MAXPRO VMS SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CONFIGURING THE MAXPRO VMS SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
VERIFYING THE CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SETTING UP THE CLIENT AND THE SERVER COMPUTER . . . . . . . . . . . . . . . 9
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ACTIVITIES TO PERFORM IN THIS PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HARDWARE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
CONNECTING THE MONITORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CONFIGURING THE MONITOR DISPLAY PROPERTIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INSTALLING THE MAXPRO VMS SOFTWARE . . . . . . . . . . . . . . . . . . . . . 13
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
INSTALLING THE MAXPRO VMS SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HOW TO INSTALL MAXPRO VMS SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
FULL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
CLIENT ONLY INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
AFTER INSTALLING MAXPRO VMS R300 VIEWER EDITION . . . . . . . . . . . . . . . . . . . . . . . . . 37
REMOVING MAXPRO VMS R300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
AFTER REMOVING MAXPRO VMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
UPGRADING TO MAXPRO VMS R300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
UPGRADING MAXPRO VMS R300 VIEWER EDITION . . . . . . . . . . . . . . . . . . . . . . . . .45
1
MAXPRO VMS R300 VIEWER EDITION
Table of Contents
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
CONFIGURING MAXPRO VMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
ACTIVITIES TO PERFORM IN THIS PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
FIREWALL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SERVER SIDE CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
RECORDERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
OTHER RECORDERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
CLIENT CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
ULTRAKEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
CONFIGURING MAXPRO VMS R300 VIEWER EDITION . . . . . . . . . . . . . . . . . . . . . . .
ADDING PROFILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADDING SITES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADDING USERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADDING PARTITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADDING AND CONFIGURING THE RECORDERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADDING AND CONFIGURING VIDEO INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADDING AND CONFIGURING RELAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADDING AND CONNECTING ALARM INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CREATING SEQUENCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
53
54
55
56
57
58
59
60
61
VERIFYING THE CONFIGURATION OF MAXPRO VMS R300 VIEWER EDITION 63
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
ACTIVITIES TO PERFORM IN THIS PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
CHECKING THE CONNECTION WITH MAXPRO VMS SERVER . . . . . . . . . . . . . . . . . . .
CHECKING THE DEVICE LISTING IN THE DEVICES WINDOW . . . . . . . . . . . . . . . . . . . . .
CHECKING THE LIVE VIDEO FROM CAMERAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE PLAYBACK OF RECORDED VIDEO . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE PLAYBACK LOOP IN THE TIMELINE WINDOW . . . . . . . . . . . . . . . . . . . .
CHECKING THE PANNING, TILTING, AND ZOOMING . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE ACKNOWLEDGEMENT AND CLEARING OF ALARMS . . . . . . . . . . . . . . . .
CHECKING THE CREATION OF IMAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE CREATION OF CLIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE DEVICE LISTING IN MY DEVICES WINDOW . . . . . . . . . . . . . . . . . . . . .
2
64
65
66
67
68
69
70
72
73
74
ABOUT THIS GUIDE
.....
...................................
INTRODUCING MAXPRO® VMS R300 VIEWER
EDITION
...........................................................
MAXPRO® VMS R300 Viewer Edition is a scaled-down version of MAXPRO® VMS
R300 Enterprise Edition software.
Following are the key features of MAXPRO VMS R300 Viewer Edition software.
•
•
•
•
•
•
One- stop Solution- The software is tailored for monitoring multiple
Honeywell’s DVRs from a single client.
DVR Support - The following five Honeywell DVRs are supported.
•
MAXPRO NVR
•
RapidEye
•
Fusion
•
HRDP
•
HRXD
User Interface - The user interface is based on the Honeywell’s flagship
MAXPRO VMS R300 Enterprise software.
Open Architecture - The software is built using industry standard protocols
and technologies.
Scalable - The software can be upgraded to the MAXPRO VMS R300
Enterprise Edition by purchasing the appropriate license.
Easy-to-use Configuration Pages - The software provides flexible and
easy-to-use configuration pages that simplifies the discovery of cameras
connected to Honeywell recorders.
SCOPE
...........................................................
This guide helps you in:
•
•
•
•
•
Setting up the hardware for the MAXPRO VMS server and client computers
Installing the MAXPRO VMS software in server and client computer
Uninstalling the MAXPRO VMS software
Configuring the MAXPRO VMS
Verifying the configuration of MAXPRO VMS
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
3
ABOUT THIS GUIDE
Intended Audience
INTENDED AUDIENCE
...........................................................
This guide is intended for the field and commissioning engineers of MAXPRO VMS.
INSTALLATION AND COMMISSIONING GUIDE
STRUCTURE
...........................................................
The following table describes the contents of each chapter in this guide.
No
Chapter
Description
1
Commissioning Plan
Description of the process involved in
commissioning the MAXPRO VMS.
2
Setting up the Client and
the Server Computer
•
Hardware specifications for
MAXPRO VMS Server and Client
computers.
•
Procedures for connecting the
monitors, and configuring monitor
display properties.
3
Installing the MAXPRO VMS
Software
Procedure for installing MAXPRO VMS
software in the client and server
computers.
4
Configuring MAXPRO VMS
Configure the MAXPRO VMS.
5
Verifying the Configuration
of MAXPRO VMS R300
Viewer Edition
Steps to verify the configuration of
MAXPRO VMS R300.
TYPOGRAPHICAL CONVENTIONS
...........................................................
This guide uses the conventions listed in the following table.
Font
What it represents
Example
Swiss721 BT
Words or characters that you must type. The
word “enter” is used if you must type text and
then press the Enter or Return key.
Enter the password.
Menu titles and other items you select
Double-click Open from the File
menu.
Buttons you click to perform actions
Click Exit to close the program.
Heading
Installation
Cross-reference to external source
Refer to the System Administrator
Guide.
Cross-reference within document
See Installation.
Trebuchet MS
4
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
1
COMMISSIONING PLAN
.....
...................................
OVERVIEW
...........................................................
Commissioning is the process of installing, configuring, and setting up the MAXPRO
VMS hardware and software. At the end of the commissioning process, the MAXPRO
VMS system is equipped for use by operators to perform surveillance operations.
The steps in the commissioning process must be performed one after the other for
successful deployment of MAXPRO VMS .
STEPS IN THE COMMISSIONING PROCESS
...........................................................
The process of commissioning involves the following phases:
•
•
•
•
Setting up the MAXPRO VMS Server and Client Computers.
Installing the MAXPRO VMS Software.
Configuring the MAXPRO VMS System.
Verifying the Configuration.
SETTING UP THE MAXPRO VMS SERVER AND CLIENT
COMPUTERS
•
MAXPRO VMS server and client can be installed on the same machine provided
it meets the minimum hardware requirements. Additional clients can be
connected to the server to a maximum of 5.
•
Connecting the monitors to the computers after ensuring that they meet the
hardware requirements. You can connect up to four monitors to each computer.
After connecting the monitors, configure the monitor display properties.
Note:
See the chapter Setting up the Client and the Server Computer for
information on hardware requirements, how to connect the monitors to
the computers, how to configure the display properties.
INSTALLING THE MAXPRO VMS SOFTWARE
Installing the software involves:
•
Ensuring that the server and client computers meet the minimum software
requirements such as operating system and anti virus software.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
5
1
COMMISSIONING PLAN
Steps in the commissioning process
•
Installing the MAXPRO VMS R300 Viewer Edition software.
Note:
See the chapter Installing the MAXPRO VMS Software for information on
software requirements and installation instructions for the MAXPRO VMS
R300 Viewer Edition software.
CONFIGURING THE MAXPRO VMS SYSTEM
In this phase, you need to configure the MAXPRO VMS through the user interface.
Before you start configuring the MAXPRO VMS, perform the following:
•
Determine the number of sites to add in the MAXPRO VMS system. A default site
is available in MAXPRO VMS. You can use this default site only if one site is
planned for the location.
Note:
A site is typically a group of cameras that are geographically located
together but can be cameras grouped by similar scenes.
•
Determine the number of partitions to be created for each site. A default global
partition is automatically created when you add a site in MAXPRO VMS.
•
Ensure that the recorders and other video devices such as cameras are powered
on and connected to the network.
Note:
Partitions are used to limit access of cameras to users. Create partitions
for cameras that need limited user access.
•
Determine the IP addresses and username/password of the recorders. The IP
addresses are required to add the devices to the MAXPRO VMS system.
•
Determine to which site each recorder and camera needs to be associated.
•
Determine to which partition each recorder, camera needs to be associated.
•
Determine the number of users for each site. You need to create users and
associate them to roles while configuring the MAXPRO VMS system.
Note:
See the chapter Configuring MAXPRO VMS for information on how to
configure the MAXPRO VMS system.
VERIFYING THE CONFIGURATION
Verifying the configuration involves checking whether the surveillance operations
can be performed using MAXPRO VMS. Surveillance operations include, viewing the
live video, performing the pan, tilt, and zoom on the video, and starting the video
recording.
6
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
COMMISSIONING PLAN
Steps in the commissioning process
Note:
See the chapter Verifying the Configuration of MAXPRO VMS R300 Viewer
Edition for information on how to perform the verification.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
7
1
COMMISSIONING PLAN
Steps in the commissioning process
This page is intentionally left blank
8
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
2
SETTING UP THE CLIENT AND THE SERVER
COMPUTER
.....
...................................
OVERVIEW
...........................................................
Setting up the server and client computers is the first phase in the commissioning
process.
BEFORE YOU BEGIN
Determine the following at the location:
•
Number of server and client computers
•
Hardware configuration of the computers
ACTIVITIES TO PERFORM IN THIS PHASE
.The following table lists the activities to perform in this phase.
Tasks
See the section...
Ensure that the hardware configuration
of the server and client computers meet
the minimum specifications.
Hardware Specifications.
Connect the monitors configuring their
display properties.
Connecting the Monitors.
Configure the monitor display
properties
Configuring the Monitor Display
Properties
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
9
2
SETTING UP THE CLIENT AND THE SERVER COMPUTER
Hardware Specifications
HARDWARE SPECIFICATIONS
...........................................................
The MAXPRO VMS R300 Viewer Edition must meet the minimum hardware
specifications. This is necessary for proper and efficient working of the system.
There are two types of hardware configurations for the server and client namely,
minimum and recommended. The minimum configuration uses the minimum
hardware specifications. The recommended configuration uses higher hardware
specifications for better performance..
Table 2-1
MAXPRO VMS R300 Viewer Edition- Minimum Specifications
Specification Description
Processor
Intel Core®2 Duo 3.00 GHz / Dual Core 3.00
GHz/1333 MHz/4 MB L2
Operating System
Microsoft® Windows XP Professional SP2 (32-bit
only) or Microsoft ® Windows 7 Pro (32-bit and
64-bit)
Microsoft® Windows Server 2003 (32bit) or
Microsoft® Windows Server 2008 R2
RAM
4 GB
Secondary Storage
DVD-RW drive
Hard Disk
Minimum 100GB Partition drive
Network connection
1Gbit/sec or greater
Keyboard / Mouse
12 function-key keyboard and mouse
Monitor resolution
1280x1024 pixels; 65K colors non-interlaced
Graphics Adapter
Display adapter - Direct X 9 compatible 256 MB
per monitor or greater
Database
Microsoft SQL Express 2008 is automatically
installed while installing MAXPRO VMS Server
Table 2-2
MAXPRO VMS R300 Viewer Edition - Recommended
Specifications
Specification Description
Processor
Intel Core ® 2 Extreme 3.00 GHz / Quad Core
3.00 GHz/1333 MHz/12 MB
Operating System
Microsoft® Windows XP Professional SP2 (32-bit
only) or Microsoft® Windows 7 Pro (32-bit and
64-bit)
Microsoft® Windows Server 2003 (32bit) or
Microsoft® Server 2008 R2
10
RAM
4 GB
Secondary Storage
DVD-RW drive
MAXPRO VMS Express Edition Commissioning and Installation Guide
. . . . .
SETTING UP THE CLIENT AND THE SERVER COMPUTER
Hardware Specifications
Table 2-2
MAXPRO VMS R300 Viewer Edition - Recommended
Specifications
Specification Description
Hard Disk
Minimum 100GB Partition drive
Network connection
1Gbit/sec or greater
Keyboard / Mouse
12 function-key keyboard and mouse
Monitor resolution
1280x1024 pixels; 65K colors non-interlaced
Graphics Adapter
Display adapter - Direct X 9 compatible 256 MB
per monitor or greater
Database
Microsoft SQL Express 2008 is automatically
installed while installing MAXPRO VMS Server
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
11
2
SETTING UP THE CLIENT AND THE SERVER COMPUTER
Connecting the Monitors
CONNECTING THE MONITORS
...........................................................
The number of monitors that you can connect to the computer depends on the type
of graphics adapter. For example, up to four monitors can be connected to a dual
head graphics adapter.
Caution: Before you begin, ensure that the computer and monitors are
turned off.
CONFIGURING THE MONITOR DISPLAY PROPERTIES
The recommended display settings for the monitor are dialog box resolution of 1280
x 1024pixels and color quality of 65K colors non-interlaced. The display settings can
be configured from the Windows control panel or from the Windows desktop
through the context menu.
To configure the display settings from the context menu in the Windows
desktop
1.
Right-click the Windows desktop to display the context-menu.
2.
Click Properties. The Display Properties dialog box appears.
3.
Click the Settings tab.
4.
Select the dialog box resolution and color quality.
5.
Click Apply to save the settings.
6.
Click OK to close the dialog box.
To configure the display settings from the Windows control panel
1.
Go to Windows control panel.
Note:
12
To open the control panel, choose Start > Settings > Control Panel.
2.
Double-click the Display icon. The Display Properties dialog box appears.
3.
Click the Settings tab.
4.
Select the dialog box resolution and color quality.
5.
Click Apply to save the settings.
6.
Click OK to close the dialog box.
MAXPRO VMS Express Edition Commissioning and Installation Guide
3
INSTALLING THE MAXPRO VMS SOFTWARE
.....
...................................
OVERVIEW
...........................................................
This chapter describes the procedures for installing MAXPRO VMS Viewer Edition
software. Follow the appropriate section in this chapter to complete the installation.
BEFORE YOU BEGIN
1.
Ensure that the client and server computers meet the software requirements.
SYSTEM REQUIREMENTS
The client and server computers must meet the following software specifications.
Table 2-1
Software Specifications
Operating System
Microsoft® Windows 7 Professional (64-Bit and
32-Bit) Microsoft® Windows XP Professional (32Bit) for MAXPRO VMS Workstation
Microsoft® Windows Server 2008 R2 Standard
Edition (64 Bit Version) on 64 Bit Server or
Microsoft® Windows Server 2003 R2 Standard
Edition Service Pack 2 (32 Bit Version) on 32 Bit
Server for MAXPRO VMS Server.
Antivirus
McAfee® VirusScan 8.8, or Symantec™ Antivirus
V10
Monitor Resolution
1024x768 pixels, 65K colors non-interlaced
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
13
3
INSTALLING THE MAXPRO VMS SOFTWARE
Installing the MAXPRO VMS Software
INSTALLING THE MAXPRO VMS SOFTWARE
...........................................................
To complete the MAXPRO VMS installation follow the procedures in these sections.
1.
First, How to Install MAXPRO VMS Software
2.
Choose the installation that best suits your requirements and follow the
appropriate steps.
•
•
14
Full Installation
Client Only Installation
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
How to Install MAXPRO VMS Software
HOW TO INSTALL MAXPRO VMS SOFTWARE
...........................................................
To install MAXPRO VMS software
1.
Insert the MAXPRO VMS R300 Viewer Edition DVD in the DVD drive. The setup
runs automatically. If the setup does not run automatically, browse to the setup
folder in the DVD and double-click Setup. exe. The Welcome dialog box
appears.
Figure 3-1
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
Welcome
15
3
INSTALLING THE MAXPRO VMS SOFTWARE
How to Install MAXPRO VMS Software
2.
Click Next. The License Agreement dialog box appears. The dialog box
displays the license agreement for the MAXPRO VMS VMS.
Figure 3-2
3.
Read the license agreement, and then click I accept the terms of the license
agreement to accept the license agreement.
4.
Click Next. The Choose Destination Location dialog box appears.
Figure 3-3
16
License Agreement
Choose Destination Location
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
How to Install MAXPRO VMS Software
Note:
5.
Click Change to change the default destination folder, and then select
the folder where MAXPRO VMS must be installed.
Click Next. The Validation of User Credentials dialog box appears.
Figure 3-4
Validation of User Credentials
6.
In the Domain Name/Host Name list, type the domain name if you know it or
select one from the list.
7.
In the User Name box, type your Windows user name.
8.
In the Password box, type your Windows password.
9.
Select the Enable Auto Logon check box if you want the computer to reboot on
its own whenever required, during the installation process. The following
message appears.
Note:
You are prompted to reboot multiple times while installing MAXPRO VMS
R300 Viewer Edition, auto log on avoids manual intervention during
multiple reboots.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
17
3
INSTALLING THE MAXPRO VMS SOFTWARE
How to Install MAXPRO VMS Software
Figure 3-5
Enabling Auto Logon
10. Click Yes to proceed with the installation. The Installation Type dialog box
appears.
Figure 3-6
Installation Type
11. Select Client Only Installation or Full Installation as required. Use the
instructions of one of the following sections that corresponds to the feature that
you are installing, Full Installation or Client Only Installation.
Table 2-2
18
Select Features to Install
Full Installation
Installs all the MAXPRO VMS R300 Viewer
Edition components (Server and Client). See Full
Installation.
Client Only
Installation
Installs only the client components of MAXPRO
VMS. See Client Only Installation.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
FULL INSTALLATION
...........................................................
To perform full installation
1.
Perform steps 1 through 11 of How to Install MAXPRO VMS Software, select Full
Installation in the Installation Type dialog box, and then click Next. The Select
Features dialog box appears.
Figure 3-7
2.
Under Device Drivers, select the check boxes corresponding to the drivers you
want to install.
Note:
3.
Select Features
Clearing the check boxes for the drivers that are not used improves the
install time. The drivers can be installed at a later time if required.
Click Next. The Start Copying Files dialog box appears.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
19
3
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
Figure 3-8
4.
Start Copying Files
If you want to review or change any settings click Back.
Note
•
•
5.
The Start Copying Files dialog box lists the total approximate time
for installing the prerequisites and total approximate time for installing
MAXPRO VMS R300 Viewer Edition components. Please note that
prerequisites take more time for installation than the MAXPRO VMS
R300 Viewer Edition components.
The pre-requisites are Microsoft components required for running of
the MAXPRO VMS application.
Click Next. The following message appears.
Figure 3-9
6.
20
Prerequisites Installation Confirmation
Click Yes to install the prerequisites automatically, else click No to install the
prerequisites manually.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
Note:
7.
From step 7onwards till the end of the installation, the prerequisites and
MAXPRO VMS components are installed automatically without requiring
any manual intervention
The SQL Server 2008 Express setup status appears.
Figure 3-10
•
SQL Server 2008 Express Setup
Your computer restarts automatically after Microsoft SQL Server 2008
Express is successfully installed.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
21
3
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
8.
After restarting, the Microsoft SQL Server 2005 Compatibility setup status
appears.
Figure 3-11
Microsoft SQL Server 2005 Compatibility Setup
•
9.
Your computer restarts automatically after Microsoft SQL Server 2005
Backward Compatibility is successfully installed.
After restarting, the SoftKey setup status appears.
Figure 3-12
•
22
SoftKey Setup
Your computer restarts automatically after SoftKey is successfully installed.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
10. After restarting, the Microsoft .NET Framework 4.0 setup status appears.
Figure 3-13
Microsoft .NET Framework 4.0 Setup
•
Your computer restarts after Microsoft .NET Framework 4.0 is successfully
installed.
11. After restating, all the Trinity Services are stopped and the MAXPRO VMS Server
setup status appears.
Figure 3-14
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
MAXPRO VMS Server Setup
23
3
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
12. After MAXPRO VMS Server is successfully installed, the MAXPRO VMS
Scheduler setup appears.
Figure 3-15
MAXPRO VMS Scheduler Setup
13. After MAXPRO VMS Scheduler is successfully installed, the Trinity Framework
setup status appears.
Figure 3-16
24
MAXPRO VMS Trinity Framework Setup
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
14. After the Trinity Framework is successfully installed, the Rapid Eye driver setup
status appears.
Figure 3-17
Rapid Eye Driver Setup
15. After the RapidEye driver is successfully installed, the PSIA IP Adapter setup
status appears.
Figure 3-18
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
PSIA IP Adapter Setup
25
3
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
16. After the PSIA IP Adapter is successfully installed, the HD3MDIP Adapter setup
status appears.
Figure 3-19
HD3MDIP Adapter Setup
17. After the HD3MDIP Adapter is successfully installed, the Honeywell IP Adapter
setup status appears.
Figure 3-20
26
Honeywell IP Adapter Setup
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
18. After the Honeywell IP Adapter is successfully installed, the Fusion driver setup
status appears.
Figure 3-21
Fusion Driver Setup
19. After the Fusion driver is successfully installed, the HRXD setup status appears.
Figure 3-22
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
HRXD Setup
27
3
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
20. After the HRXD driver is successfully installed, the HRDP driver setup status
appears.
Figure 3-23
HRDP Driver Setup
21. After the HRXD driver is successfully installed, the MAXPRO NVR driver setup
status appears.
Figure 3-24
28
MAXPRO NVR Driver Setup
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
22. After the MAXPRO NVR driver is successfully installed, the BONJOUR setup
status appears.
Figure 3-25
BONJOUR Setup
23. After the BONJOUR is successfully installed, the HD3MDIP ActiveX setup status
appears.
Figure 3-26
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
HD3MDIP ActiveX Setup
29
3
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
24. After HD3MDIP ActiveX is successfully installed, the HD4MDIP ActiveX setup
status appears.
Figure 3-27
HD4MDIP ActiveX Setup
25. After HD4MDIP ActiveX is successfully installed, the Microsoft WSE 3.0 setup
status appears.
Figure 3-28
30
Microsoft WSE 3.0 Setup
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
26. After Microsoft WSE 3.0 is successfully installed, the Honeywell ONVIF IP
Adapter setup status appears.
Figure 3-29
Honeywell ONVIF IP Adapter Setup
27. After Honeywell ONVIF IP Adapter is successfully installed, the Crystal Reports
for Visual Studio 2008 setup status appears.
Figure 3-30
Crystal Reports for Visual Studio 2008 Setup
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
31
3
INSTALLING THE MAXPRO VMS SOFTWARE
Full Installation
28. After the Crystal Reports for Visual Studio 2008 is successfully installed, the
MAXPRO VMS Client setup status appears.
Figure 3-31
MAXPRO VMS Client Setup
29. After MAXPRO VMS Client is successfully installed, the Install Shield Wizard
complete dialog box appears.
Figure 3-32
Install Shield Wizard Complete
30. Click Finish to complete the full installation. Your computer reboots
automatically. The installation is complete after the reboot operation.
32
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Client Only Installation
CLIENT ONLY INSTALLATION
...........................................................
Note:
The Client connects to a MAXPRO server application. At least one server
must to be installed to use the Client only installation.
To perform client only installation
1.
Perform steps 1 through 11 of How to Install MAXPRO VMS Software. The
Installation Type dialog box appears.
2.
Select Client Only Installation, and then click Next. The Select Features dialog
box appears.
Figure 3-33
Select Features
3.
Select the check boxes corresponding to the device drivers you want to install.
4.
Click Next. The MAXPRO VMS R300 Client Configuration dialog box appears.
Note:
Click to clear the check boxes corresponding to the device drivers that
you do not want to install.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
33
3
INSTALLING THE MAXPRO VMS SOFTWARE
Client Only Installation
Figure 3-34
5.
In the MaxproVMS Server box, type the name of the MAXPRO VMS Server.
Note:
6.
34
MAXPRO VMS R300 Client Configuration
If the MAXPRO Server server name or IP Address is not known, place a
dot “.” in the box and continue. The server IP address or Name can be
entered after the installation is complete.
Click Next. A dialog box asking for confirmation to add the client workstation to
MAXPRO VMS database appears.
•
Click Yes if you want to add the client workstation name in MAXPRO
VMS database. The Database Server Login dialog box appears. Go to
step 35.
•
Click No if you do not want to add client workstation name in MAXPRO
VMS Server database. The Start Copying Files dialog box appears. Go
to step step 10.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Client Only Installation
Figure 3-35
Database Server Login
7.
Click Browse, and then select any existing SQL database. You can select the
existing SQL database on the same network. If you do not want to select an
existing database, proceed to step 7.
8.
Select Connect using option as Windows authentication or SQL Server
authentication using Login ID and password below.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
35
3
INSTALLING THE MAXPRO VMS SOFTWARE
Client Only Installation
9.
Click Next. The Start Copying Files dialog box appears.
Figure 3-36
Note:
36
Start Copying Files
The Start Copying Files dialog box lists the total approximate time for
installing the prerequisites and total approximate time for installing
MAXPRO VMS client components. Please note that prerequisites take
more time for installation than the MAXPRO VMS components.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Client Only Installation
10. Click Next. The MAXPRO VMS client components are installed and the
InstallShield Wizard Complete dialog box appears.
Figure 3-37
Install Shield Wizard Complete
11. Click Finish. Your computer restarts and the installation is complete.
AFTER INSTALLING MAXPRO VMS R300 VIEWER EDITION
After installing the MAXPRO VMS R300 Viewer Edition, configure the Microsoft
Loopback Adapter.
To configure the Microsoft Loopback Adapter
1.
Right-click My Network Places, and then select Properties.
2.
Locate the LAN or High-Speed Internet connection that has a device name of
Microsoft Loopback Adapter, right-click, and then select Properties. The Local
Area Connection Properties dialog box appears.
3.
Select Internet Protocol (TCP/IP), and then click Properties. The Internet
Protocol (TCP/IP) Properties dialog box appears.
4.
Select Use the following IP address.
5.
In the IP address box, type the IP address between the range of 10.0.0.0 to
10.255.255.255 or 192.168.0.0 to 192.168.255.255. The subnet mask
255.255.255.0 appears in the Subnet mask box.
Note:
6.
Do not set a value for Default gateway.
Click OK.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
37
3
INSTALLING THE MAXPRO VMS SOFTWARE
Removing MAXPRO VMS R300
REMOVING MAXPRO VMS R300
...........................................................
You can remove the MAXPRO VMS completely or some of it’s components as per
your requirement.
BEFORE YOU BEGIN
1.
Stop Trinity Services.
a.Choose Start>Run, and then type services.msc. The Services window
appears.
b.Right-click TrinityContoller, and then select Stop.
c.Right-click TrinityServer, and then select Stop.
To remove MAXPRO VMS completely
1.
Insert the MAXPRO VMS R300 Viewer Edition setup DVD in the DVD drive,
browse to the MAXPRO VMS R300 Viewer Edition setup folder, and then doubleclick Setup. exe or Go to the MAXPRO VMS R300 Viewer Edition setup folder in
your computer, and then double-click Setup. exe. The Welcome dialog box
appears.
2.
Click Next. The Setup Type dialog box appears.
Figure 3-38
3.
38
Setup Type
You can remove all or only few of the MAXPRO VMS components.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Removing MAXPRO VMS R300
To remove only few components
4.
Click the Remove Few option to remove only few of the MAXPRO VMS
components. The Select Features dialog box appears.
Figure 3-39
Select Features
5.
Select the components that you wish to remove by clicking the respective check
boxes.
6.
Click Next. The Start Copying Files dialog box appears.
Figure 3-40
7.
Start Copying Files
Click Next. The selected MAXPRO VMS components are removed completely
and the Uninstall Complete dialog box appears.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
39
3
INSTALLING THE MAXPRO VMS SOFTWARE
Removing MAXPRO VMS R300
Figure 3-41
8.
Uninstall Complete
Click Finish. You are prompted to reboot the computer.
To remove all the MAXPRO VMS components
9.
Click the Remove All option in the Setup Type dialog box to remove all the
MAXPRO VMS components.
10. Click Next. The following confirmation message appears.
Figure 3-42
40
Confirmation Message
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Removing MAXPRO VMS R300
11. Click Yes. The Restoring TrinityDatabase dialog box appears.
Figure 3-43
Restoring Trinity Database
12. Click Yes to retain the Trinity database, else click No.
13. Click Next.
14. Click Next. The MAXPRO VMS components are removed completely and
Uninstall Complete dialog box appears.
Figure 3-44
Uninstall Complete
15. Click Finish. You are prompted to reboot the computer.
16. Click OK.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
41
3
INSTALLING THE MAXPRO VMS SOFTWARE
Removing MAXPRO VMS R300
Note:
You can remove the required component using the Add or Remove
Programs in Windows. However, Honeywell recommends to follow the
above mentioned steps to remove the MAXPRO VMS components.
AFTER REMOVING MAXPRO VMS
After removing MAXPRO VMS, remove Microsoft Loopback Adapter manually.
To remove loopback adapter
1.
Right-click My Computer, and then select Properties. The System Properties
dialog box appears.
Figure 3-45
42
System Properties
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Removing MAXPRO VMS R300
2.
Click Device Manager. The Device Manager screen appears.
Figure 3-46
3.
Expand the Network Adapter branch, right-click Microsoft Loopback Adapter,
and then select Uninstall. The Confirm Device Removal dialog box appears.
Figure 3-47
4.
Device Manager
Confirm Device Removal
Click OK.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
43
3
INSTALLING THE MAXPRO VMS SOFTWARE
Upgrading to MAXPRO VMS R300
UPGRADING TO MAXPRO VMS R300
...........................................................
OVERVIEW
This chapter describes the procedure for upgrading MAXPRO VMS software from
VMS R300 Viewer Edition to MAXPRO VMS R300. Follow the appropriate section in
this chapter to complete your MAXPRO VMS software migration.
BEFORE YOU BEGIN
1.
44
Ensure that the client and server computers meet the software requirements.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
INSTALLING THE MAXPRO VMS SOFTWARE
Upgrading MAXPRO VMS R300 Viewer Edition
UPGRADING MAXPRO VMS R300 VIEWER EDITION
...........................................................
See the procedures in the following sections to upgrade to MAXPRO VMS R300
Enterprise Edition.
BEFORE YOU BEGIN
1.
Stop Trinity Services.
a.Choose Start>Run, and then type services.msc. The Services window
appears.
b.Right-click TrinityContoller, and then select Stop.
c.Right-click TrinityServer, and then select Stop.
To upgrade to MAXPRO VMS R300
1.
Insert the MAXPRO VMS R300 Viewer Edition DVD in the DVD drive. The setup
runs automatically. If the setup does not run automatically, browse to the setup
folder on the DVD and double-click Setup. exe. The Setup Type dialog box
appears.
Figure 3-48
2.
Setup Type
Select the Install option.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
45
3
INSTALLING THE MAXPRO VMS SOFTWARE
Upgrading MAXPRO VMS R300 Viewer Edition
3.
Click Next. The Select Features dialog box appears.
Figure 3-49
4.
Select the device drivers you want to upgrade by clicking the respective check
boxes.
5.
Click Next. The Start Copying Files dialog box appears.
Figure 3-50
6.
46
Select Features
Start Copying Files
Click Next. The setup status of various components appears. The Upgrade
Complete dialog box appears after the upgrade is successful.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
4
CONFIGURING MAXPRO VMS
.....
...................................
OVERVIEW
...........................................................
Configuring MAXPRO VMS involves setting up the application to perform
surveillance operations. This is the most important phase for commissioning
MAXPRO VMS as it involves organizing devices, users, and roles associated to
them.
ACTIVITIES TO PERFORM IN THIS PHASE
In this phase, using the MAXPRO VMS user interface perform the tasks listed in the
following table.
Task
0n...
Adding Profiles
page 53
Adding Sites
page 54
Adding Client Workstations
page 55
Adding Users
page 55
Adding Partitions
page 56
Adding and configuring Recorders
page 57
Adding and configuring Video Inputs
page 58
Adding and configuring Relays
page 59
Creating Sequences
page 61
Adding Desktop Shortcuts
page 74
BEFORE YOU BEGIN
•
•
Ensure that you have completed MAXPRO VMS server and client hardware
setup and software installation.
Configure the firewall settings as mentioned in the Firewall Settings section.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
47
4
CONFIGURING MAXPRO VMS
Firewall Settings
FIREWALL SETTINGS
...........................................................
See the tables in the following sections while configuring the firewall settings for
MAXPRO VMS.
SERVER SIDE CONFIGURATION
The following server side application executable files need to be excluded with the
following port configuration.
48
Application
Description
Port
Type
Port
Number
Trinity.SystemServic
es.exe
Server Operations
TCP
Custom
20007
Controller
TCP
Custom
26026
DNS Server
TCP
Custom
53
Trinity.Controller.exe
Controller
Operations
TCP
Custom
26026
Scheduler
Scheduler
Operations
TCP
Custom
20010
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
CONFIGURING MAXPRO VMS
Firewall Settings
RECORDERS
Programs
Ports
Port
Type
Port
Number
DCOM Services
TCP
Standard
135
File and Printer
Sharing
TCP
Standard
139, 445
TCP
Standard
137, 138
DNS Server
TCP
Standard
53
Client and Server
Communication
TCP
Standard
80
OTHER RECORDERS
Recorder
Name
Port
Type
Port Number
Fusion
TCP
Custom
4000
RapidEye
TCP
Custom
10000
HRXD
TCP
Custom
8016
TCP
Custom
10019
HRDP
TCP
Custom
4000
MAXPRO
NVR
TCP
Custom
20007
TCP
Custom
26026
CLIENT CONFIGURATION
Application Name
Purpose
Type
Port
Number
MMShell.Exe
Server Connection
Custom
20007
Rendering
Connection
Custom
20009
Controller
Custom
26026
DNS Server
Standard
53
Client Connection
Custom
20007
DNS Server
Standard
53
Trinity.RenderingServer.exe
ULTRAKEY
To avoid UltraKey device from going offline on a firewall enabled environment,
please allow the following in the firewall rules.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
49
4
50
CONFIGURING MAXPRO VMS
Firewall Settings
•
ICMP 'echo-request' (type 8) packets out.
•
ICMP 'echo-reply' (type 0) packets in.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
CONFIGURING MAXPRO VMS
Configuring MAXPRO VMS R300 Viewer Edition
CONFIGURING MAXPRO VMS R300 VIEWER
EDITION
...........................................................
You can configure the MAXPRO VMS R300 using the Configurator tab in the user
interface. The navigation area inside the Configurator tab helps configure devices,
groups, and manage users and roles.
To go to configurator tab
1.
Double-click the icon
2.
In the Username box, type the user name. The default user name is “admin”.
3.
In the Password box, type the password. The default password for the default
user name “admin” is “trinity”.
4.
Click
on the desktop. The Log On dialog box appears.
. The Viewer tab appears by default.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
51
4
CONFIGURING MAXPRO VMS
Configuring MAXPRO VMS R300 Viewer Edition
5.
52
Click Configurator tab. The Configurator screen appears.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
CONFIGURING MAXPRO VMS
Adding Profile
ADDING PROFILE
...........................................................
Server addresses are saved in profiles. You need a profile to log on to MAXPRO VMS
You can add, modify, and delete a profile through the log on dialog box.
To add, modify or delete a profile
1.
Double-click the icon
2.
Click Server Settings. The Server Settings dialog box appears.
3.
You can add, delete or modify a profile using the Server Settings dialog box.
Note:
on the desktop. The Log On dialog box appears
For more information on how to add profiles, refer to the MAXPRO VMS
R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
53
4
CONFIGURING MAXPRO VMS
Adding Sites
ADDING SITES
...........................................................
A site is added to associate cameras, recorders, switchers, and monitor. By default,
one site is available in MAXPRO VMS R300 Viewer Edition. If only one site is needed
at the location, you can use the default site. Any number of sites can be added as
per your requirements.
To add a site
1.
Go to Configurator tab.
2.
Expand the Groups branch in the navigation area, and then click Sites.
Note:
54
For more information on how to add sites, refer to the MAXPRO VMS
R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
CONFIGURING MAXPRO VMS
Adding Users
ADDING USERS
...........................................................
By default, user named “admin” is created with administrator role. This user is
privileged to add new users, assign roles to them, and associate them to partitions,
event groups, workstations, and joystick controllers. You can restrict a user from
viewing and modifying the settings of video devices. You can also dissociate
privileges to a user.
To add a user
1.
Go to Configurator tab.
2.
Expand the User Management branch in the navigation area, and then click
Users.
Note:
For more information on how to add users, refer to the MAXPRO VMS
R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
55
4
CONFIGURING MAXPRO VMS
Adding Partitions
ADDING PARTITIONS
...........................................................
Devices and users are associated to partitions. Only users associated to a partition
can use the devices in that partition. By default, a partition is created and all the
devices and users are associated with it. You can create any number of partitions
based on the requirements.
You can associate devices and users to a partition while you are adding them. You
can also dissociate the partition from devices and users.
To add a partition
1.
Go to Configurator tab.
2.
Expand the Groups branch in the navigation area, and then click Partitions.
Note:
56
For more information on how to add partitions, refer to the MAXPRO VMS
R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
CONFIGURING MAXPRO VMS
Adding and Configuring the Recorders
ADDING AND CONFIGURING THE RECORDERS
...........................................................
You can add a recorder and modify the settings as per your requirements. You can
also select the site for the recorder, and associate partitions and events.
To add and configure a recorder
1.
Go to Configurator tab.
2.
Expand the Devices branch in the navigation area, and then click Recorders.
Note:
For more information on how to add and configure recorders, refer to the
MAXPRO VMS R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
57
4
CONFIGURING MAXPRO VMS
Adding and Configuring Video Inputs
ADDING AND CONFIGURING VIDEO INPUTS
...........................................................
You can add and configure both digital and analog cameras in MAXPRO VMS.
Recorders are associated with the cameras. Cameras can be associated to partitions
for logical grouping.
To add and configure cameras
1. Go to Configurator tab.
2. Expand the Devices branch in the navigation area, and then click Video Inputs.
Note:
58
For more information on how to add and configure cameras, refer to the
MAXPRO VMS R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
CONFIGURING MAXPRO VMS
Adding and Configuring Relays
ADDING AND CONFIGURING RELAYS
...........................................................
You can add or delete a relay in MAXPRO VMS R300 Viewer Edition. Relays can be
connected to devices like recorders, cameras. Relays send signals that perform
various actions. For example, you can set a relay to open the door automatically
when a motion is detected in a particular region.
To add and configure relays
1.
Go to Configurator tab.
2.
Expand the Devices branch in the navigation area, and then click Relays.
Note:
For more information on how to add and configure relays, refer to the
MAXPRO VMS R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
59
4
CONFIGURING MAXPRO VMS
Adding and connecting Alarm Inputs
ADDING AND CONNECTING ALARM INPUTS
...........................................................
You can add alarm inputs to raise alarms through an external device in MAXPRO
VMS.
To add alarm inputs
1.
Go to Configurator tab.
2.
Expand the Devices branch in the navigation area, and then click Alarm Inputs.
Note:
60
For more information on how to add alarm inputs, refer to the MAXPRO
VMS R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
CONFIGURING MAXPRO VMS
Creating Sequences
CREATING SEQUENCES
...........................................................
After you have configured all the devices and users, you have the option of creating
sequences. Sequences display live video from the cameras or presets for a
specified time interval. You can select the cameras or presets to be included in a
sequence and also specify the time interval for which the video from each camera or
preset is displayed.
To create sequences
1.
Go to Configurator tab.
2.
Expand the Groups branch in the navigation area, and then click Sequences.
Note:
For more information on how to create sequences, refer to the MAXPRO
VMS R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
61
4
CONFIGURING MAXPRO VMS
Creating Sequences
This page is intentionally left blank
62
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
5
VERIFYING THE CONFIGURATION OF MAXPRO
VMS R300 VIEWER EDITION
.....
...................................
OVERVIEW
...........................................................
Verifying the configuration of the MAXPRO VMS R300 Viewer Edition is the final
phase in the commissioning process. In this phase, you need to verify the working of
the MAXPRO VMS R300 Viewer Edition.
BEFORE YOU BEGIN
Ensure that the configuration of the MAXPRO VMS R300 Viewer Edition is complete.
ACTIVITIES TO PERFORM IN THIS PHASE
In this phase, using the MAXPRO VMS user interface, perform the following tasks to
verify the configuration.
Task
0n...
Connection with the MAXPRO VMS server (logging on)
page 64
Device listing in the Devices window
page 65
Live video display from cameras
page 66
Playback of recorded video
page 67
Playback of loop (mark in and mark out feature) in Timeline
window
page 68
Panning, tilting, and zooming functions (analog PTZ and Digital
PTZ)
page 69
Acknowledgement of alarms and clearing of alarms
page 70
Image creation
page 72
Clip creation
page 73
Saving the salvo layout using the salvo view feature
page 84
Device listing in My Devices window
page 74
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
63
5
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Connection with MAXPRO VMS server
CHECKING THE CONNECTION WITH MAXPRO VMS
SERVER
...........................................................
The MAXPRO VMS can consist of one or more servers. You can save the address of
each server in profiles from the Log On dialog box that appears when you start
MAXPRO VMS . The Log On dialog box is illustrated in the following figure.
To connect to a MAXPRO VMS R300 Viewer Edition server from the client
computer
1.
Click the language selection option, and then select the required language from
the drop-down list. The supported languages are Chinese, German, French, and
Arabic. The default language is English.
Note:
You can localize the language using the localization tool. For more
details, refer to the MAXPRO VMS R300 Viewer Edition Localization
Guide. pdf which is available on the DVD.
2.
In the Username box, type the user name. The default user name is “admin”.
3.
In the Password box, type the password. The default password for the default
user name “admin” is “trinity”.
4.
In the Profile box, select the profile in which the server address is saved.
5.
Click
. The MAXPRO VMS dialog box is displayed.
You can set a profile as the default profile. When a profile is set as default, you need
not select the profile each time you log on to MAXPRO VMS R300 Viewer Edition.
You can also modify and delete profiles.
Note:
64
Refer to the MAXPRO VMS R300 Viewer Edition Help for more
information on how to save server addresses in profiles, how to set a
profile as default profile, and how to modify and delete profiles.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Device Listing in the Devices Window
CHECKING THE DEVICE LISTING IN THE DEVICES
WINDOW
...........................................................
By default, the Viewer tab is selected when you log on to MAXPRO VMS R300
Viewer Edition. The Devices window lists the recorders, along with the cameras
connected to them in a tree structure. Similarly sequences are listed in the
Sequences window, salvo views are listed in the Views window. A drop-down box
on the top of the Devices window lists the partitions. The following figure illustrates
the Viewer tab and the various windows.
Ensure that all the devices, sequences, and salvo views added to the MAXPRO VMS
R300 Viewer Edition are listed in the respective windows.
Note:
Refer to the MAXPRO VMS R300 Viewer Edition Help for more
information.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
65
5
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Live Video from Cameras
CHECKING THE LIVE VIDEO FROM CAMERAS
...........................................................
To ensure that all the cameras are connected and functioning properly, you need to
check for live video from them.
To select the cameras and view live video
•
Double-click the camera in the Devices window or My Devices window. You can
also drag the camera on a panel in the salvo layout. The panel starts displaying
live video and the label Live appears over the video display.
The camera can also be selected using the virtual keyboard and joystick controller.
You can select multiple cameras and view live video in different panels of the salvo
layout.
Note:
66
Refer to the MAXPRO VMS R300 Viewer Edition Help for more
information on how to view live video from cameras.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Playback of Recorded Video
CHECKING THE PLAYBACK OF RECORDED VIDEO
...........................................................
To playback video, the recording from the camera must be available and the
recording settings for the camera must be configured. You can find out the status of
the camera by the colored indicator on the camera icon in the site view. If the
indicator on the camera icon is green means the camera is active. If the indicator on
the camera is red means it is recording.
Recorded video can be played from the Timeline window. When you select a
camera to view video, a timeline corresponding to the camera appears in the
Timeline window. The name of the camera appears on the left of the timeline.
To play recorded video from a camera, you can click the timeline at the point from
which you want to play video. A timescale is displayed in the lower part of the
Timeline window. You can refer to the divisions in the timescale to locate the date
and time. You can also select a date and time from which you want to play recorded
video using the date and time options in the timeline window.
Color codes are used in the timeline to indicate the availability of video recording for
the cameras connected to the IP engine. The time duration for which recording is
available is indicated in green color. The time duration for which recording is not
available is indicated in white color.
For cameras connected to other recorders such as Rapid Eye, Fusion, Enterprise
and Intellex, the color codes are not displayed in the timeline. However, you can
click a point in the timeline to play recorded video.
The label Rec is displayed in red color on the panel displaying recorded video from
a camera.
Note:
For more information on how to play recorded video from the Timeline
window and how to use the player controls, refer to the MAXPRO VMS
R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
67
5
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Playback Loop in the Timeline Window
CHECKING THE PLAYBACK LOOP IN THE TIMELINE
WINDOW
...........................................................
Loops are used for repeatedly playing a portion of video. Mark in and mark out
points are used to create a loop in the Timeline window. You can add a mark in point
to mark the start date and time of the loop in the timeline. To mark the end date and
time of the loop, add a mark out point in the timeline. The following figure illustrates a
loop in the timeline.
Figure 0-1
Note:
68
Loop in the timeline
For more information on how to create loops by adding mark in and mark
out points and how to play a loop, refer to the MAXPRO VMS R300
Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Panning, Tilting, and Zooming
CHECKING THE PANNING, TILTING, AND ZOOMING
...........................................................
In MAXPRO VMS R300 Viewer Edition, you can perform two types of PTZ namely,
analog PTZ and Digital PTZ. Using the digital PTZ feature, you can perform panning
and tilting on live and recorded video and clips. The digital PTZ feature when
enabled allows you to perform panning and tilting on the video display that is
zoomed or enlarged in a panel.
You need to perform both analog and digital PTZ on cameras to verify the
functioning.
Note:
For more information on how to perform analog and digital PTZ, refer to
the MAXPRO VMS R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
69
5
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Acknowledgement and Clearing of Alarms
CHECKING THE ACKNOWLEDGEMENT AND CLEARING
OF ALARMS
...........................................................
Alarms notify the occurrence of events and event attributes to the operators. You can
configure alarms to be triggered when events such as recorder disk space nearing
full, motion detection, and others happen. The event attributes that are associated to
events are listed in the details of the alarm in Alarm window. The events that trigger
an alarm can be selected while configuring the recorders, cameras, and switchers.
Events can be associated to event groups.
Each alarm goes through the following states.
New or Unacknowledged
When an alarm is triggered it appears in the Alarm window. You can click the Alarm
tab to view the Alarm window. The state of the alarm after it is triggered is referred to
as unacknowledged. You can view the list of all the unacknowledged alarms in a
table in the Alarm window. The following figure illustrates the Alarm window.
The number of unacknowledged alarms is displayed in a blinking mode in the status
bar in red color. For example, Alarms (10) indicate that there are ten
unacknowledged alarms. You can select various options using the context menu or
shortcut menu by right clicking on the Alarms window. The options include:
•
Acknowledge (ACK)
•
Clear on ACK
•
Show Video
•
Show Preview Pane
•
Freeze
•
Receive Alarms Only
•
Receive Events Only
•
Receive both Alarms and Events
Acknowledge
An acknowledged alarm indicates that the operator has taken the action. After
acknowledging the alarm, it is moved to the acknowledged alarms list in the Alarm
window. You can also use the Acknowledge button below Alarms window. To clear
acknowledged alarms, use the Clear button below Acknowledged list window.
Clear on ACK
This option clears the alarms which are acknowledged.
Show Video
Select this option if you want to view video from which the alarm was generated.
Show Preview Pane
This option gives you four windows which display alarms which are on, pre-alarm,
post alarm, and live alarm videos.
Freeze
Select this option if you no longer wish to receive alarms.
Receive Alarms Only
Select this option if you want to receive only alarms.
Receive Events Only
70
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Acknowledgement and Clearing of Alarms
Select this option if you want to receive only Events.
Receive both Alarms and Events
Select this option receive both alarms and events.
Note:
For more information on how to acknowledge and clear alarms, refer to
the MAXPRO VMS R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
71
5
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Creation of Images
CHECKING THE CREATION OF IMAGES
...........................................................
A frame of video displayed in the panel can be saved as an image. The image can be
saved in Bitmapped Graphics (BMP), Joint Photographic Experts Group (JPG)
format, Portable Graphics format (PNG), and Graphics Interchange Format (GIF).
Only the images saved in the ImagesAndClips folder at the location in the hard
drive in which MAXPRO VMS R300 files are installed can be viewed in the Image/
Clip window. You can double-click the image view option in the Image/Clip window
to view images on the salvo layout. You can also select the image size large,
medium, and small as per the requirement.
For example, X:\ProgramFiles\Honeywell\TrinityFramework\ImagesAndClips.
Here, X: is the disk drive.
The images can also be saved in other folders on the computer.
Note:
72
For more information on how to save and view images, refer to the
MAXPRO VMS R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
. . . . .
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Creation of Clips
CHECKING THE CREATION OF CLIPS
...........................................................
Clips can be created from recorded video and saved in MP4, MPG, AVI, and WMV
format depending on the format supported by the recorders. Only the clips saved in
the ImagesAndClips folder at the location in the hard drive in which MAXPRO VMS
R300 files are installed can be viewed in the Image/ Clip window.
For example, X:\ProgramFiles\Honeywell\TrinityFramework\ImagesAndClips.
Here, X: is the hard drive.
The clips can also be saved in other folders on the computer.
The clips can be saved with digital signatures. Digital signatures ensure authenticity
of clips. Digital signatures are primarily used to authenticate videos that are
produced in courts as evidence. A digital signature generates a unique string for the
clip using algorithms recommended by the World Wide Web Consortium (W3C)
standards. If the video in the clip is modified, a verification check for the unique
string fails indicating that the content is tampered. When a clip is saved with the
digital signature, a package file with the.PKG extension is created to save the clip.
Note:
For more information on how to save and view images, refer to the
MAXPRO VMS R300 Viewer Edition Help.
A salvo layout that is customized based on the preferences of the operators is
referred to as a salvo view. Cameras and sequences that are selected frequently and
the preferred salvo layout can be saved as a salvo view. The saved salvo views
appear in the Views window.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
73
5
VE R I F Y I N G T H E C O N F I G U RA T I O N O F M A X P R O V M S R 3 0 0 V I E W E R E D I T I O N
Checking the Device Listing in My Devices Window
CHECKING THE DEVICE LISTING IN MY DEVICES
WINDOW
...........................................................
In the My Devices window, operators can group the video sources, which are
frequently selected such as cameras, monitors, and sequences. If you group the
video sources, it is easy to select and you need not search in the Devices window,
which generally consists of many video sources. You can also group the devices
under shared devices. Devices grouped under shared devices are displayed on all
client workstations irrespective of the logged in user.
Note:
74
For more information on how to add a video source to My Devices
window and how to create folders to group them, refer to the MAXPRO
VMS R300 Viewer Edition Help.
MAXPRO VMS R300 Viewer Edition Commissioning and Installation Guide
Honeywell Video Systems (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
www.honeywellvideo.com
 +1.800.796.2288
Honeywell Video Systems Northern Europe
Netwerk 121
1446 WV Purmerend, The Netherlands
www.honeywell.com/security/nl
 +31.299.410.200
Honeywell Security Australia Pty Ltd.
Unit 5, Riverside Centre, 24-28 River Road West
Parramatta, NSW 2150, Australia
www.honeywellsecurity.com/au
 +61.2.8837.9300
Honeywell Systems Group
Aston Fields Road, Whitehouse Ind Est
Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security/uk
 +44 (0)1928 756999
Honeywell Security Asia Pacific
33/F Tower A, City Center, 100 Zun Yi Road
Shanghai 200051, China
www.asia.security.honeywell.com
 +86 21.2527.4568
Honeywell Security South Africa
Unit 6 Galaxy Park, 17 Galaxy Avenue
Linbro Park, P.O. Box 59904
2100 Kengray, Johannesburg, South Africa
www.honeywell.co.za
 +27.11.574.2500
Honeywell Security Asia
Flat A, 16/F, CDW Building, 388 Castle Peak Road
Tsuen Wan, N.T., Hong Kong
www.asia.security.honeywell.com
 +852.2405.2323
Honeywell Security France
Parc Gutenberg, 8, Voie La Cardon
91120, Palaiseau, France
www.honeywell.com/security/fr
 +33.01.64.53.80.40
Honeywell Security Italia SpA
Via Treviso 2 / 4
31020 San Vendemiano
Treviso, Italy
www.honeywell.com/security/it
 +39.04.38.36.51
Honeywell Security España
Mijancas 1. 3a Planta
P.Ind. Las Mercedes
28022 Madrid, Spain
www.honeywell.com/security/es
 +34.902. 667.800
Honeywell Security Deutschland
Johannes-Mauthe-Straße 14
D-72458 Albstadt, Germany
www.security.honeywell.com/de
 +49.74 31.8 01.0
Honeywell Security Poland
Chmielewskiego 22a, 70-028
Szczecin, Polska
www.ultrak.pl
 +48.91.485.40.60
Honeywell Security Czech Republic
Havránkova 33, Brno
Dolní Heršpice, 619 00, Czech Republic
www.olympo.cz
 +420.543.558.111
Honeywell Security Slovakia Republic
Vajnorská 142, 83104 Bratislava
Slovakia
www.olympo.sk
 +421.2.444.54.660
www.honeywellvideo.com
HVSsupport@honeywell.com
Document 800-11111 – Rev A – 1/2012
© 2012 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However,
Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information
contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such
changes.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising