QUICK-START GUIDE RELOOP RMX-90DVS Installation and Setup The Reloop RMX-90DVS requires drivers on Windows, but is a classcompliant device for OS X and macOS. For Windows, please make sure you have the latest drivers installed, by visiting Reloop’s website (http://www.reloop.com/downloadfinder/), or allowing Serato DJ to install the bundled driver. It is always important to connect your mixer directly to your computer, rather than a USB hub. Please also ensure you have installed the latest available version of Serato DJ (1.9.6 or above required). The Reloop RMX-90DVS is a Serato DJ and DVS enabled device, and does not require a license to use Serato DJ, nor the DVS expansion pack, however additional purchases may be required to use other expansion packs. User Guide For further information on RMX-DVS90 controls and details on indvidual features please refer to the Reloop RMX-DVS90 Hardware User Guide. Download the RMX-DVS90 User Guide from the Reloop website here. MIXER 3 4 5 6 7 8 9 2 11 1 15 # 1 10 14 13 RMX-DVS90 Control 12 Function AC POWER IN Connect AC power cable 2 POWER SWITCH Mixer On/Off 3 MASTER Master RCA output 4 REC OUT Record RCA output 5 CH-4 INPUT Line / CD input for channel 4 6 CH-3 INPUT Phono / CD input for channel 3 7 GROUNDING POST Connect grounding wire from turntables 8 CH-2 INPUT Phono / CD input for channel 2 9 GROUNDING POST Connect grounding wire from turntables 10 CH-1 INPUT Line / CD input for channel 1 11 KENSINGTON SLOT Secure mixer with Kensington lock 12 BOOTH OUT Booth TRS output 13 MASTER Master XLR output 14 ACTIVE USB HUB Allow for additional USB devices and accessories 15 USB PORT Connect USB cable to computer 7 6 8 9 # 5 4 10 RMX-DVS90 Control 1 HEADPHONE INPUTS 3.5mm and 6.35mm headphone inputs 2 CUE SECTION Cue Vol, Mix, EQ, and Split controls 3 MIC1/2 & AUX SECTION Microphone & AUX controls 4 MIC1 IN Microphone 1 input 5 AUX IN Auxiliary input 6 CHANNEL METER Monitor channel level 7 INPUT SOURCE SELECT Input source select knob for each channel 8 CHANNEL CONTROLS Volume, Headphone Cue, Sound Filter, Channel fader, and EQ controls for each channel. 9 MASTER CONTROLS Master and booth output channel meter and controls 11 3 12 2 1 16 15 14 13 Function 10 BEAT FX LCD RMX-DVS90 Beat FX display 11 FADER/XFADER START & CURVES Adjust Channel/Cross Fader curves, and enable Channel/Cross Fader start 12 BEAT FX CONTROLS Beat FX controls 13 MIC2 IN Microphone input 14 BEAT FX MODIFIERS Adjust Beat FX parameters 15 CROSS FADER Fade between channels 16 CROSS FADER ASSIGN Assign channels to cross fader A-B DVS Control Recording The Reloop RMX-DVS90 mixer is a Serato DVS Enabled device, and unlocks DVS functionality when connected to your PC or Mac. You are able to record the software mix with Serato DJ and the RMXDVS90. To make sure your mixer is set up for recording, open the SETUP screen and click the AUDIO tab. Select a channel to nominate for recording, under the ‘Record Channel’ section. Select Primary Decks Also in the AUDIO tab of the SETUP screen, you will need to select your Primary Decks. Choosing Channel 1 and 2, will allow you to have a traditional 1-2-3-4 channel configuration. Choosing Channel 2 and 3 will allow you to have a 3-1-2-4 configuration (from left to right across the mixer). Select which deck configuration you are using with the mixer and change if necessary. If you notice you are getting signal from your control tone but on the wrong deck, you might need to double-check your Primary Decks in the SETUP screen or the physical inputs on the back of the mixer. You are now set up to use your mixer with Serato DJ and DVS control using the REL or ABS control modes. See the Serato DJ manual for more information on Control Modes. For more information, please refer to the RMX-DVS90 mixer’s hardware manual. MIDI Using the Tool Tips The MIDI feature in Serato DJ provides the ability to remap Serato DJ software functions to your primary Serato DJ controller, interface or mixer. You can also assign controls to a secondary MIDI controller to further enhance your performance. For more information on MIDI mapping with Serato DJ click here. Click on the icon to enable Tool Tips. This is located in between the MIDI and setup button in the top right hand corner of the screen. Tool Tips provide a handy way to learn the various features of Serato DJ. To remap your supported Serato DJ device, open the SETUP screen and click the MIDI tab. If your Serato DJ device supports hardware remapping it will show up in the MIDI Devices list at the top. Select your connected device from the MIDI Devices list and make sure the “Enable MIDI device” option is checked. If you wish to allow re-mapping for primary hardware (like the RMX-90DVS), ensure the following option is enabled; Once checked, the MIDI assign button at the top of the screen will become available for you to start remapping. You can save, edit or delete MIDI presets in the MIDI tab of the SETUP screen. Clicking ‘Restore Defaults’ will erase any custom mappings for all connected devices and revert their functions back to default. Download the Serato DJ software manual for further information. NOTE: Official Serato Accessories do not currently support user remapping. Hardware features that cannot be remapped at this stage are Jogwheels/ Platters, Input Switches, Shift buttons and Performance Pad Mode buttons. Re-mapping any pad(s) in Hot Cue mode will also re-map the same pad in Saved Flip mode and vice versa. Move the mouse over a section of the screen to bring up a context sensitive tool tip. Holding the mouse over the button with Tool Tips turned on will show you a list of all keyboard shortcuts. For more information about how to use Serato DJ, please go to our website www.serato.com or download the Serato DJ Manual. For more information on your RMX-DVS90, please refer to the Pioneer RMXDVS90 hardware manual.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project