312517B RentalPro HVLP, Three

312517B RentalPro HVLP, Three
INSTRUCTIONS--PARTS LIST
312517B
RentalPro HVLP, Three-Stage
HVLP Turbine Sprayer
120 Vac 60 Hz
RentalPro HVLP with Three-Stage Turbine
Model 255680
6 psi (41 kPa, 0.4 bar) Maximum Working Pressure
Model descriptions are in Turbine
Components Table on page 4.
Related Manuals
HVLP Turbine Spray Gun . . . . . . . . . . . . . . . . . . 309205
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
7947A
3800 Shown
GRACO INC.
P.O. BOX 1441
MINNEAPOLIS, MN 55440--1441
ECOPYRIGHT 2007, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
ti10738a
Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Component Identification and Function . . . . . . . . . . . . 5
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . 18
Graco Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Symbols
Warning Symbol
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
Caution Symbol
CAUTION
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames, or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D Ground the equipment. See Grounding on page 6.
D If there is any static sparking or you feel an electric shock while using this equipment, stop
spraying immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
D When flammable liquid is sprayed or used for flushing or cleaning the equipment, the turbine must
be placed at least 20 feet (6.1 m) away from areas where hazardous concentrations of flammable
vapors are likely to occur.
D Use additional air hose if necessary to ensure that the turbine is operated in a clean, dry,
well-ventilated area.
D Never place the turbine inside a spray booth! Use this equipment outdoors or in extremely
well-ventilated areas.
D Keep the spray area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the spray area.
D Extinguish all open flames or pilot lights in the spray area.
D Do not smoke in the spray area.
D Do not turn on or off any light switch in the spray area while operating or if fumes are present.
D Do not operate a gasoline engine in the spray area.
2
312517
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
INSTRUCTIONS
D This equipment is for professional use only.
D Read all instruction manuals, tags, and labels before you operate the equipment.
D Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.
D Do not alter or modify this equipment. Use only genuine Graco parts.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure of the lowest-rated system component.
HVLP 3800 turbine has a working pressure of 6 psi (0.4 bar, 41 kPa).
D Use fluids and solvents that are compatible with the equipment wetted parts. See Specifications
on page 17 for wetted parts information.
D Do not use hoses to pull equipment.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82_C (180_F) or below --40_C (--40_F).
D Wear hearing protection when operating this equipment.
D Do not lift pressurized equipment.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
D Do not point the gun at anyone or at any part of the body.
D Do not put your hand or fingers over the gun fluid nozzle.
D Do not stop or deflect leaks with your hand, body, glove, or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Follow the Pressure Relief Procedure on page 10 if the fluid nozzle clogs and before you clean,
check, or service the equipment.
D Tighten all fluid connections before you operate the equipment.
D Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state, and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
D Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents, or
fluids containing such solvents in the turbine spray system, which contains aluminum and/or
galvanized-coated parts. Such use could result in a serious chemical reaction, with the possibility
of explosion, which could cause death, serious injury, and/or substantial property damage.
312517
3
General Information
HVLP Turbine Sprayers
Unpacking Turbine
The RentalPro HVLP 3800 Turbine Sprayer, and spray
gun can spray most coatings or finishes currently
being used for automotive refinish, industrial,
aerospace, marine, wood, plastic, and architectural
applications.
Unpack the Graco Turbine Sprayer from the shipping
carton, and inspect for any possible shipping damage.
If there is any damage, call your distributor.
To produce high-quality paint finishes, the spray gun
typically utilizes inbound air pressure of 6 psi (0.4 bar,
41 kPa). A cone of air, produced by the gun, carries
and directs the paint from the gun to the surface,
minimizing overspray and increasing transfer
efficiency. This enables painters to comply with new
clean air laws that are designed to reduce VOC
(volatile organic compounds) emissions, eases paint
application by requiring fewer paint passes to obtain
coverage, and saves on both material and clean-up
time.
See HVLP Turbine Spray Gun manual 309205 for
more information on the operation and use of the
turbine spray gun.
Turbine Components Table
System
Model
30-ft (9 m) Hose
HVLP 3800
255680
241413
Gun /
Fluid Set
Extra/Fluid Sets
244117 nonbleeder style cup gun with
244125 (#4)
244126 (#5)
244124 (#3)
4
312517
Component Identification and Function
C
D
B
K
J
L
A
E
F
H
7947b
Fig. 1
A
Air outlet
Connection for turbine air supply to HVLP Turbine Spray Gun
B
Power switch
ON/OFF switch for sprayer turbine and rear outlet
C
Storage compartment
Provides storage for fluid set components
D
Turbine handle
Folds flat for minimum storage space
E
Turbine case
Houses air filter and provides dual air flow to motor and turbine
F
Air filters (pre-filter and main)
Provide filtered air for turbine spray gun and turbine motor
H
Air filter indicator light
Indicates air filter performance and maintenance
J
Connector and power cord
Provides power for turbine sprayer (power cord provided with turbine)
K
Auxiliary power outlet
Switched power outlet for compressor/cart or other accessory
L
Resettable circuit breaker
Provides protection for turbine motor and cart
312517
5
Setup
Grounding
Prepare the Fluid
WARNING
Improper installation or alteration of the grounding
plug will result in a risk of electric shock, fire, or
explosion that could cause serious injury or death.
This equipment requires a 120 Vac, 60 Hz, 15A circuit
with a grounding receptacle. See Fig. 2.
grounded outlets
D Always strain the fluid before you spray; this
includes color, reducer, and hardeners if used.
D When using a turbine spray system, use a
slower drying reducer or thinner to compensate for
the faster drying time caused by the warm air of the
turbine. Do not over reduce.
CAUTION
The performance of the turbine sprayer varies with
the viscosity of the material and the length of the
hose. Keep the hose short to prevent pressure drop.
Paint Reduction — Automotive Type Finishes
grounding prong
Fig. 2
Extension cord must be 3-wire, 12 AWG, 50 ft (15 m)
or shorter.
Do not alter the ground prong or use an adapter.
Reduce and catalyze all paint to manufacturer’s
specifications. To compensate for the faster drying
time of turbine systems, use a reducer that is one step
slower than what is used for conventional air spray.
Paint Reduction — Industrial or Domestic
Coatings
Reduce and catalyze all paint to manufacturer’s
specifications. If no reductions are given, first
thoroughly mix the fluid to be sprayed. Then gradually
mix in the proper reducer, testing the fluid until you
have the correct spraying consistency.
To test the consistency, remove the stir stick from the
thinned paint. When the paint stream running off the
stir stick breaks into droplets, the first few drops should
be about 1 second apart.
6
312517
Setup
Basic Sprayer Connection
Connect to Fluid and Air Supply
Connect to Electric Supply
Hand tighten all air connections:
Plug turbine power cord into grounded outlet.
HVLP 3800
NOTE: Extension cord must be 3-wire, 12 AWG, 50 ft
(15 m) or shorter.
1. Fig. 3. Connect air valve (L) to quick-disconnect (M).
2. Connect air valve to air supply hose (A).
3. Connect quick-disconnect to gun air inlet (C).
4. Connect other end of air supply hose to turbine
outlet.
C
M
L
Spray Gun
A
B
Turbine
Fig. 3
ti10890a
312517
7
Setup
Fill the Cup
Spray Gun Cup
WARNING
The spray gun cup is pressurized by the air supply
to the gun. To reduce the risk of serious injury from
pressurized fluid or accidental spray from the gun,
always turn off the air supply to the gun before you
remove the spray gun cup.
Only fill the cup 3/4 full to help keep the air pressure
tube clean, then install the cover. The under-cup cover
has a latch (H) to secure it to the cup. The over-cup (J)
has threads that keep the lid in place when tightened in
place on the cup.
H
02845b
Fig. 4
8
312517
Setup
Prepare Surface to be Sprayed
To get proper adhesion, make sure surface is
completely clean.
Operating Turbine
WARNING
Sparks can be expected in the normal operation of
the turbine motor. These sparks can ignite fumes
from flammable liquids, dust particles, and other
flammable substances in the spray area. This can
cause serious injury and property damage. Be sure
to follow the precautions below:
D When flammable liquid is sprayed or used for
flushing or cleaning equipment, the turbine must
be placed at least 20 ft (6.1 m) away from areas
where hazardous concentrations of flammable
vapors are likely to occur.
D Use additional air hose if necessary to ensure
that the turbine is operated in a clean, dry, well
ventilated area.
D Never place the turbine inside a spray booth!
Use this equipment outdoors or in extremely
well ventilated areas.
D Avoid all ignition sources such as: static
electricity from plastic drop cloths, open flames
like pilot lights, hot objects like cigarettes, arcs
from connecting or disconnecting power cords,
and turning light switches on and off. Extinguish
or remove all sources of ignition.
1. Turn turbine ON a few minutes before spraying to
allow warm-up.
NOTE: When the turbine is not in use for an extended
period of time, turn it off. The turbine does not shut off
automatically.
2. Be sure turbine filter is clean before operating. See
page 11 to check and clean filter.
NOTE: To adjust the spray gun pattern see the turbine
gun manual.
312517
9
Shutdown
Pressure Relief Procedure
WARNING
PRESSURIZED EQUIPMENT HAZARD
The equipment stays pressurized until pressure is
manually relieved. To reduce the risk of a serious
injury from pressurized fluid, accidental spray from
the gun, or splashing fluid, follow the Pressure
Relief Procedure whenever you
D
D
D
D
Are instructed to relieve the pressure
Stop spraying
Check or service any of the system equipment
Install or clean the fluid nozzles
1. Turn off air supply to gun.
2. Turn off turbine sprayer.
WARNING
The turbine hose outlet may be hot. Carefully check
the hose end before you remove the hose.
3. If using a spray gun cup:
Unlatch cup cover; loosen or remove cup from
cover to relieve cup pressure.
4. Clean spray gun and cup as instructed in the
HVLP Turbine Spray Gun manual 309205.
10
312517
Maintenance
Daily
The turbine systems are lifetime lubricated. The only
maintenance required is filter cleaning and
replacement.
The turbine filter must be clean at all times to provide
sufficient air flow to cool motor and atomize the fluid.
Check turbine pre-filter (22) daily for cleanliness.
Check the main filter (21) weekly, minimum. Clean as
necessary.
WARNING
To avoid damage to the turbine and possible electric shock, never install a damp filter in the turbine.
CAUTION
To keep out dirt, do not operate the turbine sprayer
without both filters installed.
1
NOTE: To check filter, turn on turbine and place piece
of paper against pre-filter. If air intake holds paper in
place, filter is okay.
20
21
22
The RentalPro HVLP 3800 sprayer has an air filter
indicator light on the front panel. If the filter is good the
light is out. If the filter is clogged or has low airflow the
light will come on as in Fig. 5 below.
16
Fig. 6
8049A
Fig. 5
ti10739a
Weekly
Check hose for cracks, leaks, and holes. Replace if
necessary.
To clean filter:
1. Turn off and unplug turbine.
2. Loosen four thumbscrews (16), remove filter
retainer (15) and pre-filter (22). See Fig. 6.
3. Remove main filter (21) and clean by using one of
the following three methods:
D
15
Tap filter gently on flat surface, dirty side
down.
Annually or Every 600 Hours, Whichever
Comes First
Replace motor brushes 600 hours after turbine sprayer
operation. If brushes are not replaced, motor failure
will occur.
NOTE: It is recommended that an authorized service
center perform the motor brush replacement procedure
on page 13.
CAUTION
To prevent damage to filter, do not use compressed
air on a wet filter.
D
Direct compressed air (100 psi [7 bar, 70 kPa]
maximum) through filter panel in the opposite
direction of arrows on side of filter (from the
clean side to the dirty side).
D
Soak filter for 15 minutes in water and mild
detergent. Rinse filter until clean. Air dry. Do
not use compressed air on damp or wet filter.
312517
11
Troubleshooting
PROBLEM
No fluid delivery
CAUSE
No material, no remote
container pressurization, hose
or pickup tube clogged
SOLUTION
Check container for material.
Check for leaks at the container gasket. Tighten if
loose.
Check for air flow from male quick-disconnect at
compressor outlet (should be approx. 1/4 CFM).
Turn pressure regulator clockwise. Look for pressure
on gauge. (If no pressure on gauge, check air line and
fittings).
Check for obstructions.
Check if fluid pickup tube is unplugged. Tighten.
Blow out and clear material hose.
Turbine not starting
No power
Check outlet for power. Cycle red rocker switch.
Check circuit breaker(38). Push to reset.
Poor atomization
Circuit breaker trips
12
312517
Dirty filter
Clean filter.
Extension cord too long
Extension cord must be 3-wire, 12 AWG, 50 ft (15 m)
or shorter.
Hose too long
Replace with shorter hose. See Accessories page
NO TAG for shorter hose and Part No.
Filter clogged
Clean filter and replace as necessary.
High ambient temperature
Move turbine to cooler area.
Excessive brush wear
Remove cover and turbine, and check for free motor
rotation and for brush wear. Replace motor brushes if
necessary.
Excessive current draw
Return to authorized service center.
Repair
Motor Brush Replacement
WARNING
NOTE: It is recommended that this procedure be
performed by an authorized service center.
Turn off turbine and unplug power for the following
procedures.
1. Use Turbine Sprayer Disassembly procedure at
left to take turbine apart. Use Turbine/Motor
Replacement on page 14 to replace turbine.
Turbine Sprayer Disassembly
1. If necessary, clean and replace filter according to
maintenance procedure on page 11.
2. Remove plastic fan cover.
2. Place turbine upside down on work surface.
Remove four cap screws (27) and bumpers (7).
See Fig. 7 below and Parts Drawing on page 15.
3. Remove brushes. Check commutator for
excessive wear.
3. Carefully lift unit by turbine baseplate (2) from
turbine cover (1), and place upright on work
surface.
Note: Do not install new brushes in a turbine in which
the commutator has been damaged by the brush
holders. A motor with this type of damage cannot be
repaired.
4. Repair or replace items as required.
4. Install new motor brushes using reverse order.
Keep lead wires from all rotating parts and motor
frame.
5. Reassemble turbine.
27
7
CAUTION
Do not run the motor with the air inlet or outlet
sealed off.
2
1
5. Reassemble turbine.
6. Run motor 30 to 45 minutes at half-rated voltage
to seat motor brushes.
Note: If half-rated voltage is not available, run repaired
unit in series with another turbine for 30 to 45 minutes.
A
7949A
Fig. 7
Power Cord Replacement
Replace power cord by unplugging from IEC connector
(A). Install new cord. See Fig. 7
312517
13
Repair
Turbine/Motor Replacement
See the Turbine/Motor Replacement Kits in the Parts
List on page 16 for a listing of replacement kit parts.
See Parts Drawing on page 15.
1. Use Turbine Sprayer Disassembly procedure on
page 13 to take turbine apart.
2. Remove turbine gasket (25).
3. Remove 3 screws (6).
4. Remove plate (82) and 3 spacers (83).
5. Remove turbine motor wires from spade
connectors.
6. Rotate turbine (24) from outlet fitting (18) and lift
up from turbine spacers (23).
7. Install new turbine gaskets (25 and 41).
8. Reassemble turbine.
9. Connect ground wire to turbine housing as
required.
10. Reconnect wires according to Fig. 8 schematics.
Motor
HVLP 3800 Turbine
Fig. 8
14
312517
7245A
Parts Drawing
81
29
13
27
14
26
28
6
20
21
1
22
25
15
82
6
24
83
16, 17
19
18
4
47
62
23
46
80
64
41
32, 40
5
63
10
42
12
11
39
65
36
12
38
67
34
33
7
27
69
3
6 4
37
68
ti8604b
312517
15
Parts List
Ref
No.
Part No.
Description
1
2
276674
192775
3
4
5
6
7
10
11
12
13
14
15
16
17
18
19
20
21
22†
23
24*
25
26
27
28
192786
114669
192787
114670
113817
114064
114065
114410
244166
197054
197057
192895
158486
192779
156698
192789
240273
240274
192780
240270
192788
192784
114531
113414
COVER, turbine
BASE PLATE, turbine
(HVLP 3800)
PLATE, retaining
SCREW, pan hd
DUCT, turbine
SCREW, cap, hx hd
BUMPER
PLUG, inlet
PLUG, inlet, female
SCREW, pan hd, torx
LID, tool box
FOAM PAD, tool box
RETAINER, filter
SCREW, captive
O-RING
FITTING, outlet
O-RING, buna--n
GASKET, filter
FILTER, main, paper
FILTER, pre
SPACER, turbine
TURBINE KIT, 3 stage; 120 volts
GASKET, turbine
BRACKET, handle
SCREW, cap, hx hd
NUT, lock
Qty
1
1
1
4
1
8
4
1
1
6
1
1
1
4
4
1
1
2
1
1
3
1
1
2
8
2
Ref
No.
Part No.
Description
29
32
33
34
36
37
38
39
40
41
42
46
47
62
63
64
192785
114279
114280
114293
111593
102063
114403
192905
193059
192845
192846
114287
192810
244117
241335
M71638
65
66
67Y
68Y
69
79
80
81
82
83
245202
15R248
193095
193096
193126
M70399
M70402
114538
194094
194096
15T693
HANDLE, turbine
1
SENSOR, pressure
LIGHT, indicator
1
SWITCH, rocker, red
1
SCREW, grounding
1
WASHER, lock, external tooth
1
BREAKER, circuit; 15A, 120V
1
PLATE, deflector
1
GASKET, sensor
1
GASKET, duct
1
GASKET, duct
1
FITTING, barbed
1
HOSE, air
1
GUN, HVLP
1
HOSE, air, 30 ft, black
1
VALVE, air control; includes ref. no.
80
1
CORD SET, 10 ft,13A, 120V
1
LABEL, front, HVLP 3800
2
LABEL, danger
LABEL, warning
LABEL, caution
QUICK-DISCONNECT, male
1
QUICK--DISCONNECT, female
1
SCREW, mach, pan hd
2
PLATE, turbine
1
SPACER, turbine
3
GUIDE, Quick Tips
Y
† Pre-filters are available in 5 packs. Order 240274.
* Turbine Brush Kit 240546 (purchase separately).
Y Extra danger and warning labels are available
for free.
16
312517
Qty
Specifications
Power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Vac, 60 Hz
Ampere at 120 Vac
HVLP 3800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 phase, 12A minimum
Power cord (extension cord must be 3-wire, 12 AWG, 50 ft [15 m] or shorter)
HVLP 3800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 AWG, 3-wire, 10 ft
Unrestricted flow rate
HVLP 3800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 cfm
Turbine stages
HVLP 3800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Maximum turbine hose length
HVLP 3800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 ft (18 m)
Cup volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 quart (0.95 liter)
Wetted parts
Bare spray gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . stainless steel, brass, PTFE, hard-coated aluminum
Spray gun cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . aluminum, polyethylene
Turbine shipping weight
HVLP 3800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 lb (15.4 kg)
Turbine diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.7 in (144.78 mm)
Sound level per ISO 3744
Sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89.0 dB(A)
Sound pressure level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78.0 dB(A)
312517
17
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor, or call 1--800--690--2894 to identify the nearest distributor.
All written and visual data contained in this document reflect the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 312517
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC.
P.O. BOX 1441
MINNEAPOLIS, MN 55440--1441
www.graco.com
18
312517
Revised 4/2008
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising