Actuator LA35

Actuator LA35
PRO D U C T DATA S H EE T
Actuator LA35
The LA35 is a very quiet and powerful actuator, and
provides a practical and cost-effective solution with low
power consumption. The actuator is designed for a variety
of both indoor and outdoor applications.
Features:
• 12 or 24 V DC Permanent magnetic motor
• Thrust 6000 N in push and 4000 in pull
• Max. speed up to 19.5 mm/sec. depending on load
and spindle pitch
• Stroke length from 100 to 600 mm
• Built-in endstop switches
• Stainless steel inner tube
• Protection class: IP66 (dynamic) and IP69K (static)
Options in general:
• Large variety of back fixtures and piston rod eyes
• Anti rotating piston rod eye
• Guided nut (only with 2mm pitch)
• Integrated brake for high self-locking ability
• Exchangeable cables in different lengths
• Long life absolute feedback
• Safety nut in push
• Special anodised housing for extreme environments
• Potential free endstop signals
• IC options including:
- IC - Integrated Controller
- Hall sensor
- Analogue or digital feedback for precise positioning
- Endstop signals (not potential free)
- Ready signal for diagnostics
Usage:
• Duty cycle at 6000N and 3mm pitch is max. 10%
• Ambient operating temperature: -25° to +60°C, full
performance from +5°C to +40°C
This TECHLINE® actuator comes with IC - Integrated controller.
For more information on our IC options, please see: www.linak.com/techline
Contents
Chapter 1
Specifications......................................................................................................................................................... 3
Technical specifications.......................................................................................................................................... 4
Load versus Stroke Length....................................................................................................................................... 5
Stroke and built-in tolerances.................................................................................................................................. 5
LA35 Dimensions................................................................................................................................................... 5
LA35 Piston Rod Eyes.............................................................................................................................................. 6
LA35 Back fixtures................................................................................................................................................. 7
LA35 Back fixture orientation................................................................................................................................. 8
Cable dimensions...............................................................................................................................................9-10
Y-cable dimensions......................................................................................................................................... 9
Power cable dimensions.................................................................................................................................. 9
Signal cable dimensions................................................................................................................................ 10
Speed and current curves................................................................................................................................ 11-12
Chapter 2
I/O specifications:
Actuator without feedback........................................................................................................................... 13
Actuator with:
Potential free endstop signal output ........................................................................................................... 14
Potential free endstop signals and relative positioning - Single Hall................................................................ 15
Potential free endstop signals and absolute positioning - Analogue feedback................................................. 16
IC............................................................................................................................................................ 17
Chapter 3
Environmental tests - Climatic........................................................................................................................... 18-19
Environmental tests - Mechanical............................................................................................................................ 20
Environmental tests - Electrical................................................................................................................................ 20
Page 2 of 20
Chapter 1
Specifications
Motor:
Permanent magnet motor 12 or 24V *
Cable:
Motor: 2 x 14 AWG PVC cable
Control: 6 x 20 AWG PVC cable **
Housing: The housing is made of casted aluminium, coated for outdoor use and in harsh conditions
Spindle part: Outer tube: Powder coated steel
Inner tube: Stainless steel AISI304/SS2333
Acme spindle: Trapezoidal spindle with high efficiency
Temperature range:
- 25o C to +60o C
- 13o F to +140o F
Full performance +5o C to +40o C
Weather protection: Rated IP66 for outdoor use. Furthermore, the actuator can be washed down with a high-pressure
cleaner (IP69K).
Noise level:
48dB (A) measuring method DS/EN ISO 3743-1 actuator not loaded.
Compatibility:
The LA35 IC is compatible with SMPS-T160 (For combination possibilities,
please see the User Manual for SMPS-T160)
*
Modbus actuators only 24V - please see the
Modbus installation guide http://www.linak.com/techline/?id3=2363.
** Special control cabels for the Modbus actuator - please see the
Modbus installation guide http://www.linak.com/techline/?id3=2363.
Be aware of the following two symbols throughout this product data sheet:
Recommendations
Failing to follow these instructions can result in the actuator suffering damage or being ruined.
Additional information
Usage tips or additional information that is important in connection with the use of the actuator.
Page 3 of 20
Technical specifications
LA35 with 12V motor
Order number
Push
Pull
Max.
Max.
Selflock
min.
(N)
Push
Selflock
min.
(N)
Pull
Pitch
(mm/
spindle
rev.)
(N)
(N)
3510xx.
6000
3520xx.
3521xx. push brake
3522xx. pull brake
* Typical speed
(mm/s)
No
Full
load
load
Standard
stroke
lengths
(mm)
in steps of
50mm
* Typical amp.
(A)
No
Full
load
load
4000
6000
4000
3
4.7
3.3
100-300
1.6
7.5
4000
4000
1500
1500
5
7.7
5.3
100-400
1.7
7.7
4000
4000
4000
4000
2500
1500
1500
2500
5
5
7.2
6.9
5.4
5.9
100-400
100-400
3.2
4.2
7.8
8.4
3530xx.
3531xx. push brake
3532xx. pull brake
1500
1500
1500
1500
1500
1500
750
1000
750
750
750
1000
9
9
9
14.0
14.2
14.4
12.3
12.6
11.2
100-500
100-500
100-500
1.7
2.9
3.0
5.9
5.5
5.4
3540xx.
3541xx. push brake
3542xx. pull brake
1000
1000
1000
1000
1000
1000
750
1000
750
750
750
900
12
12
12
19.0
17.9
16.9
17.0
16.9
15.4
100-600
100-600
100-600
1.9
5.5
5.6
5.3
5.5
5.6
Push
Pull
Max.
Max.
(N)
(N)
Selflock
min.
(N)
Push
Selflock
min.
(N)
Pull
Pitch
(mm/
spindle
rev.)
3510xx.
6000
4000
6000
4000
3
5.1
4.0
Standard
stroke
lengths
(mm)
in steps of
50mm
100-300
3520xx.
4000
4000
1500
1500
5
8.3
6.6
3521xx. push brake
3522xx. pull brake
4000
4000
4000
4000
2500
1500
1500
2500
5
5
8.0
8.0
6.7
7.0
3530xx.
3531xx. push brake
3532xx. pull brake
1500
1500
1500
1500
1500
1500
750
1000
750
750
750
1000
9
9
9
15.0
14.5
14.7
3540xx.
3541xx. push brake
3542xx. pull brake
1000
1000
1000
1000
1000
1000
750
1000
750
750
750
900
12
12
12
19.5
18.9
18.7
LA35 with 24V motor
Order number
* Typical speed
(mm/s)
No
Full
load
load
* Typical amp.
(A)
No
Full
load
load
0.9
4.2
100-400
0.8
4.8
100-400
100-400
1.4
2.1
4.3
4.6
13.9
14.1
13.9
100-500
100-500
100-500
0.6
1.2
1.5
2.6
2.9
3.0
18.9
17.8
18
100-600
100-600
100-600
0.9
1.3
1.5
2.8
2.8
2.9
* The typical values can have a variation of ± 20% on the current values and ± 10% on the speed values.
Measurements are made with an actuator in connection with a stable power supply and an ambient temperature at 20°C.
•
Self locking ability
To ensure maximum self-locking ability, please be sure that the motor is shorted when stopped.
Actuators with integrated controller have this feature incorporated.
•
When using soft stop on a DC-motor, a short peak of higher voltage will be sent back towards the power supply. It is
important when selecting the power supply that it does not turn off the output, when this backwards load dump occurs.
Page 4 of 20
Load versus Stroke Length
•
Safety factor 2.
Stroke and built-in tolerances
Platform options
Descriptions
Stroke tolerance
Example for 150 mm stroke
BID tolerance
Example for 350 mm BID
35XXXXXXXXXXXXX
All variants
+2/-2 mm
148 to 152 mm
+2/-2 mm
348 to 352 mm
LA35 Dimensions
10.2
10.2
Installation dimension
Stroke =<300 = 200 + Stroke
Stroke >300 = 250 + Stroke
Minimum installation dimension = 300 mm
29
17 13
27
26
11 17
6.1
6.1
54
22
153
116
27
233
83.5
Page 5 of 20
0.1
0.1
LA35 Piston rod eyes
2
3
4
Option “1”
AISI 303
41
19
11
M20 x1 6f
#5
Option “0” and “2”
5
6.3
5.5
#7 #6
-0.2
-0.4
0
-0.2
A
C
DETAIL
28
A
1
+0.2
0
Option “3”
#1
AISI 304
Option “4”
AISI 304
Dimensions and tolerances are after surface treatment
B
*Check hole with internal gauge DS/ISO/R 1938
6.3
"B"
#3
0
-0.2
6.3
Ø 21.8
#2
WE IMPROVE YOUR LIFE
General Tolerance:
-0.2
#7 -0.4General Surface Character:
Product:
LA35
0.3
A
"
Material:
Date:
Scale:
#4
Format:
Sheet:
Volume:
Weight:
Name:
"
6.3
+0.2
+0.1
5.5
#6
Type:
Confidential: Property of LINAK A/S GROUP HEADQUARTER, DK-6430 NORDBORG,
6.3
-0.1
-0.2
Surface treatment 9-15µm Fe/ZnNi layer acc. to
ISO 4042. It must be RoHS compliant.
Protection requirement: 500 hours salt spray test.
Steel
9 SMnPb 36 - DIN 1651
Color:
A-A
Producer:SECTION
DS/ISO 2768 m
-
()
3.2
Piston rod eye
8617 mm³
-
Ø13
0.2
Ø13
B
0
-0.2
DD-Mmm-YY
16-Sep-08
Ini:
1:1
CR (deleted)
ECO:
A3
No. of check. dim. #
7
1/ 1
Lifecycle state:
Released
Dimensions
and tolerances
are
after surface treatmen
No.:
Iter.:
Rev.:
*Check 0351010
hole with internal- gauge0 DS/ISO/R 1938
DENMARK Phone
copied or used by third party.
0.15
B +45 73 15 15 15 ; FAX +45 74 45 80 48. Not to be handed over to,
Surface treatment 9-15µm Fe/ZnNi layer acc. to
ISO 4042. It must be RoHS compliant.
Protection requirement: 500 hours salt spray test.
Steel
9 SMnPb 36 - DIN
Color:
Producer:
DS/ISO 2768 m
Material:
Type:
"B"
6.1
6.5
+0.2
-0
metric
+0.2
-0
inch
2
WE IMPROVE YOUR LIFE
General Tolerance:
General Surface Character:
Product:
Name:
LA35
Confidential: Property of LINAK A/S GROUP HEADQUARTER, DK-6430 NORDBORG,
3
The Piston Rod Eye is only allowed to turn 0 - 90 degrees.
Page 6 of 20
Piston rod
DENMARK Phone
LA35 Back fixtures
Option “A” and “B”
AISI 304
Option “C” and “D”
AISI 304
Option “E” and “F”
Stainless steel
Option “G” and “H”
Stainless steel
Page 7 of 20
LA35 Back fixture orientation
Option A = 0°
Option B = 90°
Page 8 of 20
Cable dimensions
Y-cable dimensions:
Brown:
Blue:
Violet:
Black:
Red:
Yellow:
Green:
White:
Ø 2.8mm
Ø 2.8mm
Ø 1.5mm
Ø 1.5mm
Ø 1.5mm
Ø 1.5mm
Ø 1.5mm
Ø 1.5mm
Brown:
Blue:
Violet:
Black:
Red:
Yellow:
Green:
White:
Ø 2.0mm
Ø 2.0mm
Ø 0.5mm
Ø 0.5mm
Ø 0.5mm
Ø 0.5mm
Ø 0.5mm
Ø 0.5mm
Ø 7.0 ± 0.15mm
AWG*: 14mm
AWG : 14mm
AWG : 20mm
AWG : 20mm
AWG : 20mm
AWG : 20mm
AWG : 20mm
AWG : 20mm
Ø 10.6 ± 0.15mm
Ø 7.0 ± 0.15mm
*AWG: American Wire Gauge
Power cable dimensions:
Ø 2.8mm
Ø 2.8mm
Ø 2.0mm AWG*:14mm
Ø 2.0mm AWG :14mm
*AWG: American Wire Gauge
Ø 7.0 ± 0.15mm
Page 9 of 20
Cable dimensions
Signal cable dimensions:
Violet:
Black:
Red:
Yellow:
Green:
White:
Ø 1.5mm
Ø 1.5mm
Ø 1.5mm
Ø 1.5mm
Ø 1.5mm
Ø 1.5mm
Violet:
Black:
Red:
Yellow:
Green:
White:
Ø 0.5mm
Ø 0.5mm
Ø 0.5mm
Ø 0.5mm
Ø 0.5mm
Ø 0.5mm
AWG*
AWG
AWG
AWG
AWG
AWG
: 20mm
: 20mm
: 20mm
: 20mm
: 20mm
: 20mm
Ø 7.0 ± 0.15mm
*AWG: American Wire Gauge
Page 10 of 20
Speed and current curves - 12V motor
The values below are typical values and made with a stable power supply and an ambient temperature of 20˚C.
LA35 - 12V current vs load
9
8
3520xx.
3510xx.
7
Ampere
6
3530xx.
3540xx.
5
4
3
2
1
0
0
1000
2000
3000
4000
5000
6000
7000
Load (N)
Speed (mm/s)
LA35 - 12V speed vs load
20
18
16
14
12
10
8
6
4
2
0
3540xx.
3530xx.
3520xx.
3510xx.
0
1000
2000
3000
4000
Load (N)
Page 11 of 20
5000
6000
7000
Speed and current curves - 24V motor
The values below are typical values and made with a stable power supply and an ambient temperature of
20˚C.
LA35 - 24V current vs load
6
5
3520xx.
3510xx.
Ampere
4
3540xx.
3530xx.
3
2
1
0
0
1000
2000
3000
4000
5000
6000
7000
Load (N)
LA35 - 24V speed vs load
25
Speed (mm/s)
20
3540xx.
15
3530xx.
10
3520xx.
5
3510xx.
0
0
1000
2000
3000
4000
Load (N)
Page 12 of 20
5000
6000
7000
Chapter 2
I/O specifications: Actuator without feedback
Input/Output
Specification
Comments
Description
Permanent magnetic DC motor.
Brown
12 or 24VDC (+/-)
To extend actuator:
Connect Brown to positive
12V ± 20%
24V ± 10%
Blue
Under normal conditions:
12V, max. 10A depending on load
24V, max. 5A depending on load
To retract actuator:
Connect Brown to negative
To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
Red
Not to be connected
Black
Not to be connected
Green
Not to be connected
Yellow
Not to be connected
Violet
Not to be connected
White
Not to be connected
Page 13 of 20
I/O specifications: Actuator with potential free endstop signal output
Input/Output
Specification
Description
The actuator is equipped with potential free endstop
signals out. The micro switches are normally open.
Brown
Comments
To extend actuator:
Connect Brown to positive
12 or 24VDC (+/-)
12V ± 20%
24V ± 10%
Blue
IN
OUT
Under normal conditions:
12V, max. 10A depending on load
24V, max. 5A depending on load
To retract actuator:
Connect Brown to negative
To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
Red
Potential free signal power supply (+)
10-28VDC
Black
Not to be connected
Green
Endstop signal out
Yellow
Endstop signal in
Violet
Not to be connected
White
Not to be connected
Switching capacity:
Minimum 10mA
Maximum 1A
Output voltage is the same as the input voltage
Page 14 of 20
I/O specifications: Actuator with potential free endstop signals and relative positioning - Single Hall
Input/Output
Specification
Comments
Description
The actuator is equipped with potential free endstop
signals and Single Hall that gives a relative positioning
feedback signal when the actuator moves.
Brown
12 or 24VDC (+/-)
To extend actuator:
Connect Brown to positive
12V ± 20%
24V ± 10%
Blue
Under normal conditions:
12V, max. 10A depending on load
24V, max. 5A depending on load
To retract actuator:
Connect Brown to negative
To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
White
Signal power supply (+)
10-28VDC
Black
Signal power supply GND (-)
Green
Endstop signal out
Yellow
Endstop signal in
Violet
Single Hall output (PNP)
Current consumption:
Max. 40mA, also when the actuator is not running
Output voltage is the same as the input voltage
Movement per Single Hall pulse:
3mm pitch = 0.38mm per pulse
5mm pitch = 0.63mm per pulse
9mm pitch = 1.13mm per pulse
12mm pitch = 1.5mm per pulse
Red
Output voltage min. VIN - 2V
Max. current output: 12mA
Max. 680nF
N.B. For more precise measurements, please
contact
LINAK A/S.
Frequency:
Frequency is 30-125 Hz on Single Hall output depending on load and spindle.
Overvoltage on the motor can result in shorter pulses.
Low frequency with a high load.Higher frequency
with no load.
Potential free signal power supply (+)
10-28VDC
Switching capacity:
Minimum 10mA
Maximum 1A
Page 15 of 20
I/O specifications: Actuator with potential free endstop signals and absolute positioning
- Analogue feedback
Input/Output
Specification
Comments
Description
The actuator is equipped with potential free endstop
signals and an electronic circuit that gives an analogue
feedback signal when the actuator moves.
Brown
12 or 24VDC (+/-)
To extend actuator:
Connect Brown to positive
12V ± 20%
24V ± 10%
Blue
Under normal conditions:
12V, max. 10A depending on load
24V, max. 5A depending on load
To retract actuator:
Connect Brown to negative
To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
White
Signal power supply (+)
10-28VDC
Black
Signal power supply GND (-)
Green
Endstop signal out
Yellow
Endstop signal in
Violet
Analogue feedback
Current consumption:
Max. 40mA, also when the actuator is not running
Output voltage is the same as the input voltage
Tolerances +/- 0.5V
Max. current output: 1mA
Ripple max. 200mV
Transaction delay 100ms
Linear feedback 0.5%
0-10V (Option A)
0.5-4.5V (Option B)
It is recommendable to have the actuator to
activate its limit switches on a regular basis, to
ensure more precise positioning
Red
Potential free signal power supply (+)
10-28VDC
Page 16 of 20
Switching capacity:
Minimum 10mA
Maximum 1A
I/O specifications: Actuator with IC
Input/Output
Specification
Comments
Description
Easy to use interface with integrated power electronics
(H-bridge).
The actuator can also be equipped with electronic circuit that gives an absolute or relative feedback signal.
M
H-Bridge
The version with “IC option” cannot be operated
with PWM (power supply).
Brown
Blue
12-24VDC + (VCC)
Connect Brown to positive
Note: Do not change the power supply polarity on
the brown and blue wires!
12V ± 20%
24V ± 10%
Power supply GND (-) is electrically connected to
the housing
12V, current limit 18A
24V, current limit 9A
If the temperature drops below 0°C, all current
limits will automatically increase to maximum (no
limits)
12-24VDC - (GND)
Connect Blue to negative
12V ± 20%
24V ± 10%
12V, current limit 18A
24V, current limit 9A
Red
Extends the actuator
Black
Retracts the actuator
On/off voltages:
> 67% of VIN = ON
< 33% of VIN = OFF
Input current: 10mA
Green
Endstop signal out
Output voltage min. VIN - 2V
Source current max. 100mA
Yellow
Endstop signal in
Violet
Analogue feedback:
Configure any high/low combination between 0-10V
or 0.5-4.5V
Endstop signals are NOT potential free
0-10V (Option A)
0.5-4.5V (Option B)
It is recommendable to have the actuator to
activate its limit switches on a regular basis, to
ensure more precise positioning
Single Hall output (PNP)
Movement per Single Hall pulse:
3mm pitch = 0.38mm per pulse
5mm pitch = 0.63mm per pulse
9mm pitch = 1.13mm per pulse
12mm pitch = 1.5mm per pulse
Frequency:
Frequency is 30-125 Hz on Single Hall output depending on load and spindle.
Overvoltage on the motor can result in shorter pulses.
White
Tolerances +/- 0.5V
Max. current output: 1mA
Ripple max. 200mV
Transaction delay 100ms
Linear feedback 0.5%
Ready
Output voltage min. VIN - 2V
Max. current output: 12mA
Max. 680nF
N.B. For more precise measurements, please
contact
LINAK A/S.
Low frequency with a high load.Higher frequency
with no load.
The signal is constantly high when the actuator is
in ready mode.
Failure modes: The signal goes low when:
- The current cuts off
- The temperature is out of range
(high duty cycle protection)
Page 17 of 20
Chapter 3
Environmental tests - Climatic
Test
Specification
Comment
Cold test
EN60068-2-1 (Ab)
Storage at low temperature:
Temperature: -40°C
Duration: 72h
Not connected
Tested at room temperature.
EN60068-2-1 (Ad)
Storage at low temperature:
Temperature: -25°C
Duration: 12h
Tested at low temperature.
EN60068-2-2 (Bb)
Storage at high temperature:
Temperature: +90°C
Duration: 72h
Actuator is not powered during test
Tested at room temperature.
Dry Heat
Storage at high temperature:
Temperature: +70ºC
Duration: 1,000h
Actuator is not powered during test
Tested at high temperature.
Change of
temperature
EN60068-2-2 (Bd)
Operating at high temperature:
Temperature: +60°C
Int. max. 17%
Duration: 700h
Actuator is activated
Tested at high temperature.
EN60068-2-14 (Na)
Rapid change of temperature:
High temperature: +100°C in 60 minutes
Low temperature: -30°C in 60 minutes
Transition time: <10 seconds
Duration: 100 cycles
Actuator is not powered during test
Tested at room temperature.
EN60068-2-14 (Nb)
Controlled change of temperature:
Temperature change 5°C pr. minute
High temperature: +70°C in 60 minutes
Low temperature: -30°C in 30 minutes
130 minutes pr. cycle
Duration: 1,000 cycles (90 days)
Actuator is not powered during test.
Tested at 250, 500 and 1,000 cycles at low and high temperatures.
Damp heat
EN60068-2-30 (Db)
EN60068-2-3 (Ca)
Salt mist.
EN60068-2-52 (Kb)
Damp heat, Cyclic:
Relative humidity: 93-98%
High temperature: +55°C in 12 hours
Low temperature: +25°C in 12 hours
Duration: 21 cycles * 24 hours
Actuator is not powered during test
Tested within 1 hour after condensation
That means after the upper temperature has been reached.
Damp heat, Steady state:
Relative humidity: 93-95%
Temperature: +40 ±2°C
Duration: 56 days
Actuator is not powered during test
Tested within one hour after exposure.
Salt spray test:
Salt solution: 5% sodium chloride (NaCl)
4 spraying periods, each of 2 hours
Humidity storage 7 days after each
Actuator not powered during test
Exposure time: 500 hours
Page 18 of 20
Environmental tests - Climatic
Degrees of protection
EN60529 – IP66
IP6X - Dust:
Dust-tight, No ingress of dust
Actuator is not activated during test.
IPX6 – Water:
Ingress of water in quantities causing harmful effects is not allowed
Duration: 100 litres pr. minute in 3 minutes
Actuator is not activated during test.
IPX6 – Connected actuator:
Actuator is driving out and in for 3 min.
100(l/min) jet of water is placed at the wiper ring for 3 min.
IPX6 – Connected actuator and push 6000 (N)
Actuator is driving out and in for 3 min. and
push 6000(N) at the end-pos.
100 (l/min.) jet of water is placed at the wiper ring for 3 min.
DIN40050 – IP69K
Chemicals
High pressure cleaner:
Water temperature: +80°C
Water pressure: 80 bar
Spray angle: 45°
Spray distance: 100mm
Duration: From any direction in 4x30 seconds
Actuator is not activated during test
Ingress of water in quantities causing harmful effects is not allowed.
DUNK test
The actuator has been warmed up to 85ºC for 4 hours
After this it is cooled down in 20ºC saltwater
Cooling time: 2 hours
Opened for checking salt deposit and water.
BS7691 / 96hours
Diesel 100%
Hydraulic oil 100%
Ethylene Glucol 50%
Urea Nitrogen saturated solution
Liquid lime 10% (Super-Cal)
NPK Fertilizer (NPK 16-4-12) saturated
Tested for corrosion.
Page 19 of 20
Environmental tests - Mechanical
Test
Specification
Free fall
Comment
Free fall from all sides:
Height of fall: 0.8 meter onto linoleum covered concrete
Actuator notpowered during test.
Vibration
EN60068-2-64
Random vibration:
Short time test: 6.29g RMS
Actuator is not connected
Long time test: 7.21g RMS
Actuator is not powered during test
Duration: 2 hours in each direction
EN 60068-2-6 (Fc)
Sinus vibration:
Frequency 5-200Hz
Displacement: 3.3mm pp, B 25Hz
Acceleration 4g
Number of directions: 3 (X-Z-Y)
Duration: 2 hours in each direction
Actuator is not powered during test.
Bump
EN60068-2-29 (Eb)
Bump test:
Level: 25g
Duration: 6 milliseconds x 1000 times in each direction pr. axis
Actuator is not powered during test.
Shock
EN60068-2-27 (Ea)
Shock test:
Level: Half sinus 100g
Duration: 6 milliseconds
Number of bumps: 3 shocks in each of 6 directions
Actuator is not powered during test.
Environmental tests - Electrical
Specification
Power supply
Comment
Operating voltages +7V - +27V
Over voltage +29(V) / 5min.
Reverse polarity +7 and +27(V) / 5min.
Electromagnetic fields
EN61000-4-3
30 V/m, 80%AM, 1 kHz 20 - 2.700 Mhz
10 V/m, 80% AM, 1kHz 80 - 1000 Mh
3 V/m, 80% AM, 1 kHz 1.4 - 2.0 GHz
1 V/m, 80% AM 2.0 - 2.7 GHz
Fast transients
EN61000-4-4
± 2 kV
Surge transients
EN61000-4-5
± 2 kV (42Ω output)
Radio frequency
EN61000-4-6
10 Vrms, 80% AM 0.15 - 80 MHz
All electrical tests are conducted and radiated emission (EMC) tests.
Terms of use
The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing
accurate and up-to-date information on its products.
However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and
changes without prior notice. Therefore, LINAK cannot guarantee the correct and actual status of said information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability
of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed
in its catalogues or other written material drawn up by LINAK.
All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK.
FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2016.09 . MA M9-02-306-I . Chapter 5.13
Test
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising