instruction manual
INSTRUCTION MANUAL
Contents
1
INTRODUCTION
1-2
SAFETY NOTES
3
GENERAL PACKAGE CONTENTS
4
DRONE DIAGRAM
5
REMOTE CONTROLLER DIAGRAM
6
REMOTE BATTERY INSTALLATION
7
CHARGING THE LI-PO BATTERY
8
SYNCING THE DRONE TO THE REMOTE CONTROLLER
9
FLIGHTADJUSTMENTAND SETTING
10
TROUBLESHOOTING
11
PARTS LIST
Please read through this manual before flying this product.
Please keep this manual for future reference.
Tested to comply with FCC standards.
FOR HOME OR OFFICE USE.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful
interference and
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
PROP 65 WARNING
WARNING: This product may
contain a chemical known to
the State of California to cause
cancer, or birth defects, or
other reproductive harm.
WARNING:
CHOKING HAZARD-Small parts.
Not for children under 3 years.
Manufactured in China.
Batch Ref: XXXX
Model Number: XXXX
1 . INTRODUCTION
●This product is NOT A TOY. Incorrect use can cause damage or injury.
Please use this product according to this manual. And please do not disassemble this product by yourself.
●This flying model requires practice before use. Manufacturer shall not be responsible to any damage of
the product or injury to any person.
2. SAFETY NOTES
Fly only in safe areas away from other people. Do not operate R/C aircraft within the vicinity of crowds
! CAUTION or people. R/C aircrafts are prone to accidents, failures, and radio interference. Pilots are responsible
for their actions and damage or injury occurred during the operation or as of a result of R/C aircraft models.
FORBIDDEN
Special design for indoor & outdoor, please keep it away from obstacles
This product is suitable for indoor and outdoor use, please choose a place without obstacle,
and keep distance from crowd and pets. Don’t fly it near unsafe areas, for instance, a heat source
or power lines in order to avoid damage by collision landing, entanglement and leading to a fire,
electric shock and cause of loss of lives and property.
! WARNING
Obtain the assistance of an experienced pilot
The products are suitable for more than 14 years old age. At the beginning, it will be difficult to
learn to fly. Seek the guidance of an experienced pilot to learn faster.
3. GENERAL PACKAGE CONTENTS
Li-Polymer battery
Charger
Blade x 4
4. DRONE DIAGRAM
Motor
Light strip
Receiver
board
4 Axis cover
4 Axis base
Blade
Protective frame
1
5. REMOTE CONTROLLER DIAGRAM
DO NOT DISASSEMBLE
A N TE N N A
POWER
INDICATOR
LIGHT CONTROL
F L IP PIN G
BU T TO N
F O RW AR D AN D
B AC KW AR D F IN E - TU N IN G
FAS T AN D
S LO W SPEED
F O RW AR D\ B AC KW AR D\
L E FT F LY \ RI G HT F LY
A SC E N D /DE S C E N D/
L E F T T U RN /RI G HT T U RN
LE F T A N D R IG HT
T URNIN G F IN E -T U N IN G
L E F T F LY AN D R IG H T
FLY F I N E -T U NIN G
PHOTO
VIDEO
P O W E R S W ITC H
6. REMOTE BATTERY INSTALLATION
DO NOT DISASSEMBLE
Step 1
Step 2
Battery
Cover
Open the battery cover on
the back of the controller.
Put in 6 AA batteries. Please follow by
the right“+” and “-” sign,as the picture
shown.
2
7. CHARGING THE LI-PO BATTERY
Use the charger provided to charge the battery.
Charger
! WARNING
Please use the charger included in the package
only. Connect the charger and the battery as the
picture shown.
! CAUTION
For safety concerns, battery must be charged
under adult supervision at all times.
Li-polymer Battery
LED Indicator
Green light
Red light
Battery is fully charged
Battery is charging
8. SYNCING THE DRONE TO THE REMOTE CONTROLLER
Step 1
Install the battery into the drone as the
Picture shown. Then place the aircraft on
A flat surface. Connect the battery to
The drone. The drone will turn on.
Li-polymer
Battery
Step 2
! CAUTION
Lower the throttle stick to the lowest position
then turn on the remote controller. Wait unit
the indicator stops flashing. Your drone is now
ready to fly.
The throttle
stick to lowest point
ON/OFF
Step 3
Please disconnect the battery from the drone,
when finished with use.
! WARNING
Li-polymer
Battery
Please always disconnect the battery,in order
to protect the battery from damage and to have
a longer battery live.
3
Step 4
Turn off the transmitter. If transmitter is not to
be used for a long duration, please remove the
battery for storage.
ON/OFF
9. FLIGHT ADJUSTMENT AND SETTING
It is important to practice maneuvers before flying your drone.
Before flying:
Please practice the following moves shown in the below pictures until you get
used to using the remote controller.
1. Bring the drone to an open space, standing aligned with the back of the drone.
2. Practice each exercise of the remote control as shown below, and repeat practice of
throttle up/down, sideways left/right, forward/backward, and turn left/right moves.
3. Flight simulation exercises are very important, please repeat the exercises until you
feel comfortable flying your drone flawlessly.
Mode
Illustration
Mode
Up/Down
Sideways Left/Right
Move
left
Forward/Backward
Move
right
Illustration
Up
Down
Fly
forward
Turn Left/Right
Fly
backward
! CAUTION
Make sure that no people or obstructions are in the area.
You must first practice hovering for flying safety. This is a basic flight action.
Hovering means keeping the flight vehicle in mid air in a fixed position.
Please stand approximately 5 ft diagonally being the flight vehicle.
To quickly fine tune and calibrate the drone, place it on a flat surface.
Lower the joysticks to the lower right corner. Hold this position until
the drone finishes flash continuously. The drone is now fine tuned.
4
Turn
left
Turn
right
Fine Tuning
Slowly raise the throttle stick and just as the helicopter
lift-off the ground, you can use the trim to correct the
action if the drone leans in a different direction.
1. ADJUSTMENT OF TURNING TRIM
Just before the drone lifts-off, the nose lean left/right:
When leaning right, adjust the trim to left side.
When leaning left, adjust the trim to right side.
Mode
Right
Left
Left Right
Mode
2. ADJUSTMENT OF FORWARD/BACKWARD TRIM
Just before the drone lifts-off, the nose lean forward/backward:
When leaning forward, adjust the trim to down.
Up
When leaning backward, adjust the trim up.
Forward
Backward
Down
Mode
3. ADJUSTMENT OF SIDEWAYS TRIM
Just before the drone lifts-off, the body lean left/right:
When leaning right, adjust the trim to left side.
When leaning left, adjust the trim to right side.
Left Right
Left
Right
Flipping Function:
Simple flipping operation
Press the button and then roll the joystick 1-3 times in any direction and
aircraft will roll 1-3 times.
F L IP PIN G
BU T TO N
5
10. TROUBLESHOOTING
Problem
Cause
Solution
LED blinks continuously after
flight vehicle battery inserted.
No response to controller.
Unable to sync to transmitter.
Repeat the power up initializing
process.
2
No response after battery is
connected to drone.
1. No power to drone
2. Low battery power
3. Poor contact on battery
terminals.
1. Turn on remote and ensure
drone battery is inserted properly.
2. Use fully charged batteries.
3. Re-seat the battery and ensure
good contact between battery
contacts.
3
Motor does not respond to
throttle stick,receiver LED
flashes.
Drone battery depleted.
Fully charge the battery, or replace
with a fully charged battery.
4
Main rotor spins but unable to
take off.
1. Deformed main blades.
2. Drone battery depleted
1. Replace main blades
2. Charge or replace with fully
charged battery.
5
Drone violently shakes.
1. Deformed main blades
1. Replace main blades
6
Tail still off trim after fine tuning,
or inconsistent speed during
left/right flight.
1. Damaged tail rotors
2. Damaged tail drive motor
1. Replace main blades
2. Replace the main motor
7
Drone still wanders
forward after trim adjustment
during hover.
1. Gyroscope not balanced
8
Flight vehicle still wanders left/
right after trim adjustment during
hover.
1. Motor off
2. Cone loose
1
1. Place on flat surface and reboot
1. Replace the motor
2. Tighten cone
6
11. PARTS LIST
⑤
①
⑨
④
⑦
⑥
⑧
NO
③
②
AWW INDUSTRIES™ is an innovative division of DGL Group, Ltd.
Other trademarks and trade names are those of their respective owners.
AWW INDUSTRIES,
195 Raritan Center Parkway, Edison, NJ 08837.
Name
Quantity
1
4 Axis cover
1
2
4 Axis base
1
3
Receiver board
1
4
Li-polymer Battery
1
5
Motor
4
6
A Blade
2
7
B Blade
2
8
Light strip
4
9
Protective frame
1
BATTERY WARNING:
• Do no mix alkaline, standard (carbon zinc), rechargeable (nickel hydride) batteries.
• Do not mix old and new batteries.
• Non-rechargeable batteries should not be recharged.
• Rechargeable batteries should be removed from the appliance before being charged.
• Rechargeable batteries should be charged under adult supervision only.
• Exhausted batteries should be removed.
• The supply terminals should not be short-circuited.
• Only batteries of the same or equivalent type are recommended to be used.
• Batteries should be inserted with the correct polarity.
Specifications, colors and contents may vary from illustrations.
Operates on 6x AA batteries (not included)
Please retain this package for future use.
Conforms to safety requirements of ASTM, FCC, & CPSIA.
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising