HP ProLiant DL360 Generation 4 Server Maintenance and Service

HP ProLiant DL360 Generation 4 Server Maintenance and Service
HP ProLiant DL360 Generation 4 Server
Maintenance and Service Guide
September 2004 (Second Edition)
Part Number 373553-002
© Copyright 2004 Hewlett-Packard Development Company, L.P.
Microsoft, Windows, and Windows NT are U.S. registered trademarks of Microsoft Corporation.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United
States and other countries.
Linux is a U.S. registered trademark of Linus Torvalds.
Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained
herein. The information in this document is provided “as is” without warranty of any kind and is subject to
change without notice. The warranties for HP products are set forth in the express limited warranty
statements accompanying such products. Nothing herein should be construed as constituting an additional
warranty.
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
September 2004 (Second Edition)
Part Number 373553-002
Audience Assumptions
This guide is for an experienced service technician. HP assumes you are qualified in the servicing
of computer equipment and trained in recognizing hazards in products with hazardous energy
levels and are familiar with weight and stability precautions for rack installations.
3
Contents
Illustrated Parts Catalog
7
Mechanical Components...................................................................................................................... 7
System Components............................................................................................................................. 9
Removal and Replacement Procedures
13
Required Tools................................................................................................................................... 13
Safety Considerations ........................................................................................................................ 14
Preventing Electrostatic Discharge......................................................................................... 14
Server Warnings and Cautions ............................................................................................... 14
Preparation Procedures ...................................................................................................................... 15
Powering Down the Server ..................................................................................................... 16
Extending the Server from the Rack....................................................................................... 17
Removing the Access Panel.................................................................................................... 18
Accessing the Product Rear Panel .......................................................................................... 18
Hard Drive Blank ............................................................................................................................... 19
Hard Drive ......................................................................................................................................... 21
Diskette Drive Blank.......................................................................................................................... 22
Diskette Drive .................................................................................................................................... 23
Optical Device Blank ......................................................................................................................... 24
Optical Device ................................................................................................................................... 25
Optical Device Ejector ....................................................................................................................... 26
Hot-Plug AC Power Supply ............................................................................................................... 27
Power Supply Fan Assembly ............................................................................................................. 28
Processor Fan Assembly .................................................................................................................... 29
Optical Device and Diskette Drive Interface ..................................................................................... 30
SCSI Backplane ................................................................................................................................. 31
SATA Backplane ............................................................................................................................... 32
PCI Riser Board Assembly ................................................................................................................ 33
PCI Expansion Slot Definitions.............................................................................................. 34
PCI-X or PCI Express Expansion Board............................................................................................ 34
PCI Riser Board ................................................................................................................................. 35
Power Converter Module ................................................................................................................... 36
Battery-Backed Write Cache Enabler ................................................................................................ 38
Memory Options ................................................................................................................................ 40
DIMM Installation Guidelines................................................................................................ 40
DIMM..................................................................................................................................... 40
Processor ............................................................................................................................................ 42
4
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Battery................................................................................................................................................ 45
System Board ..................................................................................................................................... 46
Re-Entering the Server Serial Number and Product ID ..................................................................... 47
Server Cabling
49
Cabling Overview .............................................................................................................................. 49
Server Cable Routing ......................................................................................................................... 50
SATA Cable Routing ......................................................................................................................... 51
Diagnostic Tools
53
SmartStart Software ........................................................................................................................... 53
SmartStart Scripting Toolkit .............................................................................................................. 54
HP Instant Support Enterprise Edition ............................................................................................... 55
Option ROM Configuration for Arrays.............................................................................................. 55
HP ROM-Based Setup Utility............................................................................................................ 56
ROMPaq Utility ................................................................................................................................. 56
System Online ROM Flash Component Utility ................................................................................. 56
Integrated Management Log .............................................................................................................. 57
Integrated Lights-Out Technology..................................................................................................... 58
Automatic Server Recovery ............................................................................................................... 58
HP Systems Insight Manager ............................................................................................................. 59
HP Insight Diagnostics....................................................................................................................... 59
USB Support ...................................................................................................................................... 59
Internal USB Functionality ................................................................................................................ 60
Server Component Identification
61
Front Panel Components.................................................................................................................... 62
Front Panel LEDs and Buttons........................................................................................................... 63
Rear Panel Components ..................................................................................................................... 64
Rear Panel LEDs and Buttons............................................................................................................ 65
System Board Components ................................................................................................................ 67
System Maintenance Switch .............................................................................................................. 68
NMI Switch........................................................................................................................................ 68
System Board LEDs........................................................................................................................... 69
System LEDs and Internal Health LED Combinations...................................................................... 70
Internal USB Connector..................................................................................................................... 72
SCSI IDs and SATA Device Numbers .............................................................................................. 73
Hot-Plug SCSI Hard Drive LEDs ...................................................................................................... 73
Hot-Plug SCSI Hard Drive LED Combinations................................................................................. 74
Optional Battery-Backed Write Cache Enabler LEDs ....................................................................... 75
Battery-Backed Write Cache Enabler LED Statuses ......................................................................... 76
Fan Module Locations ....................................................................................................................... 77
Processor Zone Fan Module LED...................................................................................................... 77
Contents
Specifications
5
79
Server Specifications.......................................................................................................................... 79
Environmental Specifications ............................................................................................................ 80
Hot-Plug Power Supply Calculations................................................................................................. 80
DDR SDRAM DIMM Specifications ................................................................................................ 80
1.44-MB Diskette Drive Specifications ............................................................................................. 81
CD-ROM Drive Specifications .......................................................................................................... 82
Ultra320 SCSI Hard Drive Specifications ......................................................................................... 83
Serial ATA Hard Drive Specifications............................................................................................... 83
Acronyms and Abbreviations
85
Index
91
7
Illustrated Parts Catalog
In This Section
Mechanical Components ................................................................................................................7
System Components .......................................................................................................................9
Mechanical Components
Item
Description
Spare Part
Number
1
Access panel
361400-001
8
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Item
Description
Spare Part
Number
2
Plastics kit
361396-001
a) Optical drive ejector assembly
30545-001
b) PCI card guide *
c) Diskette blank *
d) Optical device blank *
3
Hardware kit
361397-001
a) Screws, 6-32X0.25, T10 (4) *
b) Screw, 6-32X.187, T15 (4) *
c) Screw, M3X0.5X4, T10 (4) *
d) Expansion slot covers (2) *
e) Power supply blanking panel *
Rack Mounting Hardware
5
Rack mounting hardware kit *
360104-001
6
Cable management arm *
360105-001
*Not shown
Illustrated Parts Catalog
System Components
Item
Description
Spare Part
Number
System Components
1
Power supply fan assembly
361399-001
2
Processor fan assembly
361390-001
3
Hot-plug power supply, 460 W
361392-001
4
PCI riser bracket, with PCI riser boards
361387-001
9
10
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Item
Description
5
Processor/heatsink assembly
6
7
Spare Part
Number
a) Intel® 3.00-GHz Xeon™ 1-MB L2 cache
371751-001
b) Intel® 3.40-GHz Xeon™ 1-MB L2 cache *
361381-001
c) Intel® 3.60-GHz Xeon™ 1-MB L2 cache *
361382-001
a) 3.6 volt, 500 mAh NiMh battery *
307132-001
b) Universal battery housing with cable
349989-001
Smart Array 6i 128MB DDR 40 bit memory module
351518-001
Boards
8
System board, with processor cages and system battery
a) SCSI models
361384-001
b) SATA models *
361385-001
9
Power converter module
361393-001
10
SCSI backplane
305443-001
SATA backplane with data and power cables *
361389-001
Optical device/diskette drive interface
361395-001
11
Media Devices
12
Diskette drive, slimline, 1.44 MB
13
Optical drives
361402-001
a) CD-ROM drive, removable slimline, IDE, 24X
228508-001
b) DVD-ROM drive, removable slimline, 8X *
268795-001
Memory
14
DIMM, registered DDR SDRAM
a) 512 MB
366865-001
b) 1 GB *
367167-001
c) 2 GB *
367553-001
Hard drives
Illustrated Parts Catalog
Item
Description
15
SCSI Ultra320 universal hot-plug hard drive
16
Spare Part
Number
a) 36.4-GB 15K rpm
289241-001
b) 72.8-GB 10K rpm *
289042-001
c) 72.8-GB 15K rpm *
289243-001
d) 146.8-GB 10K rpm *
289044-001
SATA hot-plug hard drive
a) 80-GB 7.2K rpm *
353042-001
b) 160-GB 7.2K rpm *
353043-001
c) 250-GB 7.2K rpm *
353044-001
Cables
17
Diskette drive/optical drive cable *
361391-001
Miscellaneous
18
AC power cord *
187335-001
19
Battery, 3.3 V, lithium *
234556-001
20
Country kit *
361401-001
21
Return kit, pack box, and cushions *
371695-001
*Not shown
11
13
Removal and Replacement Procedures
In This Section
Required Tools .............................................................................................................................13
Safety Considerations ...................................................................................................................14
Preparation Procedures .................................................................................................................15
Hard Drive Blank .........................................................................................................................19
Hard Drive ....................................................................................................................................21
Diskette Drive Blank ....................................................................................................................22
Diskette Drive...............................................................................................................................23
Optical Device Blank....................................................................................................................24
Optical Device ..............................................................................................................................25
Optical Device Ejector..................................................................................................................26
Hot-Plug AC Power Supply .........................................................................................................27
Power Supply Fan Assembly........................................................................................................28
Processor Fan Assembly...............................................................................................................29
Optical Device and Diskette Drive Interface................................................................................30
SCSI Backplane............................................................................................................................31
SATA Backplane..........................................................................................................................32
PCI Riser Board Assembly...........................................................................................................33
PCI-X or PCI Express Expansion Board ......................................................................................34
PCI Riser Board............................................................................................................................35
Power Converter Module..............................................................................................................36
Battery-Backed Write Cache Enabler...........................................................................................38
Memory Options...........................................................................................................................40
Processor.......................................................................................................................................42
Battery ..........................................................................................................................................45
System Board................................................................................................................................46
Re-Entering the Server Serial Number and Product ID................................................................47
Required Tools
You need the following items for some procedures:
•
T-10 Torx screwdriver
14
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
•
T-15 Torx screwdriver
•
Diagnostics Utility
Safety Considerations
Before performing service procedures, review all the safety information.
Preventing Electrostatic Discharge
To prevent damaging the system, be aware of the precautions you need to follow
when setting up the system or handling parts. A discharge of static electricity
from a finger or other conductor may damage system boards or other staticsensitive devices. This type of damage may reduce the life expectancy of the
device.
To prevent electrostatic damage:
•
Avoid hand contact by transporting and storing products in static-safe
containers.
•
Keep electrostatic-sensitive parts in their containers until they arrive at staticfree workstations.
•
Place parts on a grounded surface before removing them from their
containers.
•
Avoid touching pins, leads, or circuitry.
•
Always be properly grounded when touching a static-sensitive component or
assembly.
Server Warnings and Cautions
Before installing a server, be sure that you understand the following warnings
and cautions.
WARNING: To reduce the risk of electric shock or damage
to the equipment:
Removal and Replacement Procedures
•
Do not disable the power cord grounding plug. The grounding
plug is an important safety feature.
•
Plug the power cord into a grounded (earthed) electrical outlet
that is easily accessible at all times.
•
Unplug the power cord from the power supply to disconnect
power to the equipment.
•
Do not route the power cord where it can be walked on or
pinched by items placed against it. Pay particular attention to
the plug, electrical outlet, and the point where the cord extends
from the server.
15
WARNING: To reduce the risk of personal injury from hot
surfaces, allow the drives and the internal system components to
cool before touching them.
CAUTION: Do not operate the server for long periods without
the access panel. Operating the server without the access panel results
in improper airflow and improper cooling that can lead to thermal
damage.
Preparation Procedures
To access some components and perform certain service procedures, you must
perform one or more of the following procedures:
•
Extend the server from the rack ("Extending the Server from the Rack" on
page 17).
If you are performing service procedures in an HP, Compaq branded, telco,
or third-party rack cabinet, you can use the locking feature of the rack rails to
support the server and gain access to internal components.
For more information about telco rack solutions, refer to the
RackSolutions.com website (http://www.racksolutions.com/hp).
•
Power down the server ("Powering Down the Server" on page 16).
16
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
If you must remove a server from a rack or a non-hot-plug component from a
server, power down the server.
•
Remove the server from the rack.
If the rack environment, cabling configuration, or the server location in the
rack creates awkward conditions, remove the server from the rack.
Powering Down the Server
WARNING: To reduce the risk of personal injury, electric
shock, or damage to the equipment, remove the power cord to
remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the
power supply and some internal circuitry remain active until AC
power is removed.
IMPORTANT: If installing a hot-plug device, it is not necessary to
power down the server.
1. Back up the server data.
2. Shut down the operating system as directed by the operating system
documentation.
3. If the server is installed in a rack, press the UID LED button on the front
panel. Blue LEDs illuminate on the front and rear panels of the server.
4. Press the Power On/Standby button to place the server in standby mode.
When the server activates standby power mode, the system power LED
changes to amber.
5. If the server is installed in a rack, locate the server by identifying the
illuminated rear UID LED button.
6. Disconnect the power cords.
The system is now without power.
Removal and Replacement Procedures
17
Extending the Server from the Rack
NOTE: If the optional cable management arm option is installed, you
can extend the server without powering down the server or
disconnecting peripheral cables and power cords. These steps are only
necessary with the standard cable management solution.
1. Power down the server ("Powering Down the Server" on page 16).
2. Disconnect all peripheral cables and power cords from the server rear panel.
3. Loosen the thumbscrews that secure the server faceplate to the front of the
rack.
4. Extend the server on the rack rails until the server rail-release latches engage.
WARNING: To reduce the risk of personal injury or
equipment damage, be sure that the rack is adequately stabilized
before extending a component from the rack.
WARNING: To reduce the risk of personal injury, be
careful when pressing the server rail-release latches and sliding
the server into the rack. The sliding rails could pinch your fingers.
5. After performing the installation or maintenance procedure, slide the server
back into the rack:
a. Press the server rail-release latches and slide the server fully into rack.
18
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
b. Secure the server by tightening the thumbscrews.
6. Reconnect the peripheral cables and power cords.
Removing the Access Panel
WARNING: To reduce the risk of personal injury from hot
surfaces, allow the drives and the internal system components to
cool before touching them.
CAUTION: Do not operate the server for long periods without
the access panel. Operating the server without the access panel results
in improper airflow and improper cooling that can lead to thermal
damage.
1. Power down the server if the standard cable management solution is installed
("Powering Down the Server" on page 16).
NOTE: If the optional cable management arm is installed, you can
extend the server and perform hot-plug installation or maintenance
procedures without powering down the server.
2. Extend the server from the rack, if applicable ("Extending the Server from
the Rack" on page 17).
3. Lift up on the hood latch handle and remove the access panel.
Accessing the Product Rear Panel
NOTE: To access some components, you may need to remove the
cable management arm.
Removal and Replacement Procedures
To open the arm:
To close the arm:
Hard Drive Blank
CAUTION: To prevent improper cooling and thermal damage,
do not operate the server unless all bays are populated with either a
component or a blank.
19
20
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
1. Remove one of the following:
−
Remove the SCSI hard drive blank.
−
Remove the SATA hard drive blank.
To replace the blank, slide the blank into the bay until it locks into place.
Removal and Replacement Procedures
Hard Drive
CAUTION: Always power down the server if the boot partition
resides on the drive you are replacing or if you are replacing the only
drive in the server.
CAUTION: To prevent improper cooling and thermal damage,
do not operate the server unless all bays are populated with either a
component or a blank.
1. Determine the status of the hard drive from the hot-plug hard drive LEDs
("Hot-Plug SCSI Hard Drive LED Combinations" on page 74, "Hot-Plug
SCSI Hard Drive LEDs" on page 73).
2. Back up all server data on the hard drive.
3. Remove one of the following:
−
Remove the SCSI hard drive.
21
22
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
−
Remove the SATA hard drive.
IMPORTANT: When SATA hard drives are installed, SATA LED
functionality and SATA hot-plug capability are not supported currently.
To replace the drive, slide the drive into the bay until the latch mechanism
engages the server chassis, then close the latch handle to lock the drive in the
server chassis.
Diskette Drive Blank
1. Power down the server ("Powering Down the Server" on page 16).
2. Extend the server from the rack ("Extending the Server from the Rack" on
page 17).
3. Remove one of the following from the left hard drive bay:
−
Hard drive blank (on page 19)
−
Hard drive (on page 21)
4. Use a Torx T-10 screwdriver to remove the locking screw.
Removal and Replacement Procedures
5. Remove the diskette drive blank.
To replace the component, reverse the removal procedure.
Diskette Drive
1. Power down the server ("Powering Down the Server" on page 16).
2. Extend the server from the rack. ("Extending the Server from the Rack" on
page 17)
3. Remove one of the following from the left hard drive bay:
−
Hard drive blank (on page 19)
−
Hard drive (on page 21)
4. Use a Torx T-10 screwdriver to remove the locking screw.
23
24
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
5. Remove the diskette drive.
To replace the component, reverse the removal procedure.
Optical Device Blank
IMPORTANT: The ejector button is recessed to prevent accidental
ejection; it may be helpful to use a pen or similar shaped object to
access the button.
1. Press the ejector button.
Removal and Replacement Procedures
2. Remove the optical device blank.
To replace the blank, slide the blank into the bay until it locks into place.
Optical Device
1. Power down the server ("Powering Down the Server" on page 16).
IMPORTANT: The ejector button is recessed to prevent accidental
ejection; it may be helpful to use a pen or similar shaped object to
access the button.
2. Press the ejector button.
25
26
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
3. Remove the optical device.
To replace the drive, slide the drive into the bay until it clicks.
Optical Device Ejector
1. Power down the server ("Powering Down the Server" on page 16).
2. Remove all hard drives ("Hard Drive" on page 21) and the hard drive blank
(on page 19).
3. Eject the optical device (on page 25) or optical device blank (on page 24).
4. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
5. Remove the diskette drive ("Diskette Drive" on page 23).
6. Use a T-10 Torx screwdriver to remove the screws that secure the optical
device ejector to the server chassis.
7. Press the tab on the side of the optical device ejector to release it from the
chassis.
Removal and Replacement Procedures
8. Remove the optical device ejector.
To replace the component, reverse the removal procedure.
Hot-Plug AC Power Supply
This procedure assumes that the server is configured with two power supplies.
CAUTION: To prevent improper cooling and thermal damage,
do not operate the server unless all bays are populated with either a
component or a blank.
1. Perform one of the following:
−
If a conventional cable management solution is in place, unfasten the
cable management solution to access the power supply bays.
−
If the cable management arm is in place, access the rear panel (on page
18).
2. Disconnect the power cord.
27
28
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
3. Press the power supply release lever, then pull the power supply from the
server.
To replace the component, reverse the removal procedure.
Power Supply Fan Assembly
CAUTION: Do not operate the server for long periods without
the access panel. Operating the server without the access panel results
in improper airflow and improper cooling that can lead to thermal
damage.
1. Power down the server ("Powering Down the Server" on page 16).
2. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
3. Remove the access panel ("Removing the Access Panel" on page 18).
4. On models equipped with SATA drives, remove the SATA cable from the
cable clip. For cable locations, refer to the SATA cable routing information
("SATA Cable Routing" on page 51).
5. Press the latches and lift to release the power supply fan assembly from the
server.
Removal and Replacement Procedures
29
6. Remove the component from the server.
CAUTION: When replacing the component, be sure the power
converter module is properly seated in the server chassis.
To replace the component, reverse the removal procedure.
Processor Fan Assembly
CAUTION: Do not operate the server for long periods without
the access panel. Operating the server without the access panel results
in improper airflow and improper cooling that can lead to thermal
damage.
1. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
2. Remove the access panel ("Removing the Access Panel" on page 18).
3. Loosen the thumbscrew that secures the processor fan assembly to the server.
4. Push on the sheet metal tab near the thumbscrew to separate the fan tray
connector from the system board connector.
30
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
5. Remove the component from the server.
To replace the component, reverse the removal procedure.
Optical Device and Diskette Drive Interface
1. Power down the server ("Powering Down the Server" on page 16).
2. Remove all hard drives and hard drive blanks ("Hard Drive" on page 21).
3. Eject the optical device ("Optical Device" on page 25).
4. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
5. Remove the access panel ("Removing the Access Panel" on page 18).
6. Remove the diskette drive ("Diskette Drive" on page 23).
7. Disconnect the cable from the optical device and diskette drive interface
board.
8. Use a T-15 Torx screwdriver to remove the two screws securing the board to
the server chassis.
Removal and Replacement Procedures
9. Slide the board toward the front edge of the server, lift up, then slide the
board toward the rear of the server to remove the component.
To replace the component, reverse the removal procedure.
SCSI Backplane
1. Power down the server ("Powering Down the Server" on page 16).
2. Remove all hot-plug SCSI hard drives ("Hard Drive" on page 21).
3. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
4. Remove the access panel ("Removing the Access Panel" on page 18).
5. Remove the power supply fan module ("Processor Fan Assembly" on page
29).
6. Disconnect the cable from the optical device and diskette drive interface
board.
31
32
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
7. Remove the component from the server.
To replace the component, reverse the removal procedure.
SATA Backplane
1. Power down the server ("Powering Down the Server" on page 16).
2. Remove all SATA hard drives ("Hard Drive" on page 21).
3. Eject the optical device ("Optical Device" on page 25).
4. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
5. Remove the access panel ("Removing the Access Panel" on page 18).
6. Remove the optical device and diskette drive interface ("Optical Device and
Diskette Drive Interface" on page 30).
7. Disconnect all cables connected to the SATA backplane. For cable locations,
refer to the SATA cable routing (on page 51) information.
Removal and Replacement Procedures
8. Remove the component from the server.
To replace the component, reverse the removal procedure.
PCI Riser Board Assembly
CAUTION: To prevent damage to the server or expansion
boards, power down the server and remove all AC power cords before
removing or installing the PCI riser cage.
IMPORTANT: Be sure that all DIMM slot latches are closed to provide
adequate clearance before removing the PCI riser board assembly with
a half-length expansion board.
1. Power down the server ("Powering Down the Server" on page 16).
2. Extend the server from the rack, if applicable ("Extending the Server from
the Rack" on page 17).
3. Remove the access panel ("Removing the Access Panel" on page 18).
4. Remove the PCI riser board assembly:
a. Disconnect any internal or external cables connected to any existing
expansion boards.
b. Loosen the four PCI riser board assembly thumbscrews.
33
34
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
c. Lift the front of the assembly slightly and unseat the riser boards from
the PCI riser board connectors.
To replace the component, reverse the removal procedure.
PCI Expansion Slot Definitions
Slot
Board Size
Connector
Interconnect
PCI-X expansion slot 1
Half-length
133 MHz, 3.3 V
64-bit
PCI-X expansion slot 2
Full-length
133 MHz, 3.3 V
64-bit
PCI Express expansion
slot 1 (optional)
Half-length
x8
x1, x4, or x8
PCI Express expansion
slot 2 (optional)
Full-length
x8
x1, x4, or x8
PCI-X or PCI Express Expansion Board
1. Remove the PCI Riser Board Assembly ("PCI Riser Board Assembly" on
page 33).
Removal and Replacement Procedures
2. Remove any expansion board installed in the assembly.
To replace the component, reverse the removal procedure.
PCI Riser Board
1. Remove the PCI Riser Board Assembly ("PCI Riser Board Assembly" on
page 33).
2. Remove any expansion board installed in the assembly ("PCI-X or PCI
Express Expansion Board" on page 34).
3. Remove the applicable PCI riser boards from the assembly:
IMPORTANT: When removing the two parts of the riser board, pay
attention to the orientation of the slots on each side. This information is
important for subsequent procedures.
35
36
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
a. Remove the riser board with the slot for full-length expansion boards.
b. Repeat the previous step for the riser board with the slot for half-length
expansion boards, if needed.
To replace the component, reverse the removal procedure.
Power Converter Module
1. Power down the server ("Powering Down the Server" on page 16).
2. Remove all hot-plug power supplies ("Hot-Plug AC Power Supply" on page
27).
3. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
4. Remove the access panel ("Removing the Access Panel" on page 18).
Removal and Replacement Procedures
37
5. Disconnect all internal power cables.
6. Remove the fan module ("Processor Fan Assembly" on page 29).
7. Slide the power converter module toward the back of the server, then lift the
power converter module from the server.
NOTE: Cables are removed for clarity.
To replace the component, reverse the removal procedure.
38
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Battery-Backed Write Cache Enabler
The Battery-Backed Write Cache Enabler, also called the battery pack, works
with the cache module to provide transportable data protection, increase overall
controller performance, and maintain any cached data for up to 72 hours. The
NiMH batteries in the battery pack are continuously recharged through a tricklecharging process whenever the system power is on. Under normal operating
conditions, the battery pack lasts for 3 years before replacement is necessary.
CAUTION: To prevent damage to the equipment or server
malfunction, do not add or remove the battery module while an array
capacity expansion, RAID level migration, or stripe size migration is in
progress.
IMPORTANT: The battery module may have a low charge when
installed. In this case, a POST error message is displayed when the
server is powered up, indicating that the battery module is temporarily
disabled. No action is necessary on your part. The internal circuitry
automatically recharges the batteries and enables the battery module.
This process may take up to 4 hours. During this time, the array
controller will function properly, but without the performance advantage
of the battery module.
NOTE: The data protection and the time limit also apply if a power
outage occurs. When power is restored to the system, an initialization
process writes the preserved data to the hard drives.
1. Power down the server ("Powering Down the Server" on page 16).
2. Extend the server from the rack, if applicable ("Extending the Server from
the Rack" on page 17).
3. Remove the access panel ("Removing the Access Panel" on page 18).
IMPORTANT: Data in the BBWCE will be erased when you disconnect
the battery.
Removal and Replacement Procedures
4. Disconnect the battery module cable from the BBWCE and from the Smart
Array 6i memory connector on the system board.
5. Remove the battery module cable from the cable clip on the system board.
6. Remove the Smart Array 6i memory module.
7. Turn the quarter-turn fasteners counter-clockwise to unlock the module.
8. Lift the battery module from the server.
9. Remove the battery from the module.
To replace the component, reverse the removal procedure.
39
40
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Memory Options
You can expand server memory by installing PC2700 DDR SDRAM DIMMs.
The system supports up to four ECC Registered DDR SDRAM DIMMs.
NOTE: The Advanced Memory Protection option in RBSU provides
additional memory protection beyond Advanced ECC. By default, the
server is set to Advanced ECC Support. Refer to "ROM-Based Setup
Utility ("HP ROM-Based Setup Utility" on page 56)," on the
Documentation CD, for more information.
The server supports two types of memory configurations:
•
Standard memory configuration for maximum performance with up to 8 GB
of active memory (four 2-GB memory modules)
•
Online spare memory configuration for maximum availability with up to
4 GB of active memory while simultaneously supporting up to 4 GB of
online spare memory
DIMM Installation Guidelines
You must observe the following guidelines when installing additional memory:
•
DIMMs installed in the server must be Registered DDR DRAM, 2.5 volts, 64
bits wide, and ECC.
•
DIMMs in slots 1A and 2A must match.
•
DIMMs in slots 3B and 4B must match and must be installed as a pair.
•
All DIMMs installed must be the same speed. Do not install DIMM modules
supporting different speeds.
•
Install DIMMs into both slots within a single bank. DIMMs must be installed
in order. Upgrade memory by installing DIMM pairs into banks in sequential
bank order, starting with bank B.
DIMM
1. Power down the server ("Powering Down the Server" on page 16).
Removal and Replacement Procedures
41
2. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
3. Remove the access panel ("Removing the Access Panel" on page 18).
NOTE: The server ships with at least two DIMMs installed in DIMM
slots 1A and 2A.
4. If necessary, remove the PCI Riser Board Assembly ("PCI Riser Board
Assembly" on page 33).
5. Remove the DIMM.
CAUTION: Be sure to install DIMMs in the proper
configuration. Refer to the Documentation CD.
CAUTION: Use only Compaq branded or HP DIMMs. DIMMs
from other sources may adversely affect data integrity.
IMPORTANT: DIMMs do not seat fully if turned the wrong way.
To replace a DIMM, align the DIMM with the slot and insert the DIMM firmly.
When fully seated, the DIMM slot latches lock into place.
42
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Processor
CAUTION: To prevent thermal instability and damage to the
server, do not separate the processor from the heatsink. The processor,
heatsink, and retaining clip make up a single assembly.
CAUTION: To prevent possible server malfunction and
damage to the equipment, do not mix processors of different types.
To remove a processor:
1. Power down the server ("Powering Down the Server" on page 16).
2. Extend the server from the rack, if applicable ("Extending the Server from
the Rack" on page 17).
3. Remove the access panel ("Removing the Access Panel" on page 18).
4. Rotate the baffle upward.
Removal and Replacement Procedures
43
5. Release the processor retaining clips and processor locking lever.
6. Lift the heatsink and processor from the server.
To install the processor in the server:
1. Remove the protective cover from the processor.
2. Align the holes in the heatsink with the guiding pegs on the processor cage.
44
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
CAUTION: To prevent possible server malfunction or damage
to the equipment, be sure to align the processor pins with the
corresponding holes in the socket.
3. Install the processor and close the processor locking lever and processor
retaining clips.
4. Rotate the baffle into position
5. Install the access panel.
Removal and Replacement Procedures
45
Battery
If the server no longer automatically displays the correct date and time, you may
need to replace the battery that provides power to the real-time clock. Under
normal use, battery life is 5 to 10 years.
WARNING: The computer contains an internal lithium
manganese dioxide, a vanadium pentoxide, or an alkaline battery
pack. A risk of fire and burns exists if the battery pack is not
properly handled. To reduce the risk of personal injury:
•
Do not attempt to recharge the battery.
•
Do not expose the battery to temperatures higher than
60°C (140°F).
•
Do not disassemble, crush, puncture, short external contacts,
or dispose of in fire or water.
•
Replace only with the spare designated for this product.
1. Power down the server ("Powering Down the Server" on page 16).
2. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
3. Remove the access panel ("Removing the Access Panel" on page 18).
4. Remove the PCI riser cage ("PCI Riser Board Assembly" on page 33).
CAUTION: To prevent damage to the server or expansion
boards, power down the server and remove all AC power cords before
removing or installing the PCI riser cage.
46
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
5. Remove the battery.
IMPORTANT: Replacing the system board battery resets the system
ROM to its default configuration. After replacing the battery, reconfigure
the system through RBSU.
To replace the component, reverse the removal procedure.
For more information about battery replacement or proper disposal, contact an
authorized reseller or an authorized service provider.
System Board
1. Power down the server ("Powering Down the Server" on page 16).
2. Extend or remove the server from the rack ("Extending the Server from the
Rack" on page 17).
3. Remove the access panel ("Removing the Access Panel" on page 18).
4. Remove the PCI Riser Board Assembly ("PCI Riser Board Assembly" on
page 33).
CAUTION: To prevent damage to the server or expansion
boards, power down the server and remove all AC power cords before
removing or installing the PCI riser cage.
5. Remove the processor fan module ("Processor Fan Assembly" on page 29).
Removal and Replacement Procedures
47
6. Remove the BBWCE ("Battery-Backed Write Cache Enabler" on page 38).
7. Remove any DIMMs ("DIMM" on page 40).
8. Remove the processors ("Processor" on page 42).
9. Disconnect all cables connected to the system board. For additional
information, refer to "Server Cabling" ("Server Cabling" on page 49).
10. Remove the system board.
IMPORTANT: If replacing the system board or clearing NVRAM, you
must re-enter the server serial number through RBSU.
To replace the component, reverse the removal procedure.
Re-Entering the Server Serial Number and Product ID
After you replace the system board, you must re-enter the server serial number
and the product ID.
1. During the server startup sequence, press the F9 key to access RBSU.
2. Select the Advanced Options menu.
3. Select Serial Number. The following warning is displayed:
Warning: The serial number should ONLY be modified by
qualified service personnel. This value should always
match the serial number located on the chassis.
48
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
4. Press the Enter key to clear the warning.
5. Enter the serial number.
6. Select Product ID. The following warning is displayed.
Warning: The Product ID should ONLY be modified by
qualified service personnel. This value should always
match the Product ID located on the chassis.
7. Enter the product ID and press the Enter key.
8. Press the Escape key to close the menu.
9. Press the Escape key to exit RBSU.
10. Press the F10 key to confirm exiting RBSU. The server will automatically
reboot.
49
Server Cabling
In This Section
Cabling Overview.........................................................................................................................49
Server Cable Routing....................................................................................................................50
SATA Cable Routing....................................................................................................................51
Cabling Overview
This section provides guidelines that help you make informed decisions about
cabling the server and hardware options to optimize performance.
For information on cabling peripheral components, refer to the white paper on
high-density deployment at the HP website
(http://www.hp.com/products/servers/platforms).
50
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Server Cable Routing
CAUTION: When routing cables, always be sure that the
cables are not in a position where they can be pinched or crimped.
Server Cabling
SATA Cable Routing
CAUTION: When routing cables, always be sure that the
cables are not in a position where they can be pinched or crimped.
51
53
Diagnostic Tools
In This Section
SmartStart Software......................................................................................................................53
SmartStart Scripting Toolkit.........................................................................................................54
HP Instant Support Enterprise Edition .........................................................................................55
Option ROM Configuration for Arrays ........................................................................................55
HP ROM-Based Setup Utility ......................................................................................................56
ROMPaq Utility............................................................................................................................56
System Online ROM Flash Component Utility............................................................................56
Integrated Management Log.........................................................................................................57
Integrated Lights-Out Technology ...............................................................................................58
Automatic Server Recovery..........................................................................................................58
HP Systems Insight Manager .......................................................................................................59
HP Insight Diagnostics .................................................................................................................59
USB Support.................................................................................................................................59
Internal USB Functionality...........................................................................................................60
SmartStart Software
SmartStart is a collection of software that optimizes single-server setup,
providing a simple and consistent way to deploy server configuration. SmartStart
has been tested on many ProLiant server products, resulting in proven, reliable
configurations.
SmartStart assists the deployment process by performing a wide range of
configuration activities, including:
•
Configuring hardware using embedded configuration utilities, such as RBSU
and ORCA
•
Preparing the system for installing "off-the-shelf" versions of leading
operating system software
•
Installing optimized server drivers, management agents, and utilities
automatically with every assisted installation
54
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
•
Testing server hardware using the Insight Diagnostics Utility ("HP Insight
Diagnostics" on page 59)
•
Installing software drivers directly from the CD. With systems that have
internet connection, the SmartStart Autorun Menu provides access to a
complete list of ProLiant system software.
•
Enabling access to the Array Configuration Utility, Array Diagnostics
Utility, and Erase Utility
SmartStart is included in the HP ProLiant Essentials Foundation Pack. For more
information about SmartStart software, refer to the HP ProLiant Essentials
Foundation Pack or the HP website (http://www.hp.com/servers/smartstart).
SmartStart Scripting Toolkit
The SmartStart Scripting Toolkit is a server deployment product that delivers an
unattended automated installation for high-volume server deployments. The
SmartStart Scripting Toolkit is designed to support ProLiant BL, ML, and DL
servers. The toolkit includes a modular set of utilities and important
documentation that describes how to apply these new tools to build an automated
server deployment process.
Using SmartStart technology, the Scripting Toolkit provides a flexible way to
create standard server configuration scripts. These scripts are used to automate
many of the manual steps in the server configuration process. This automated
server configuration process cuts time from each server deployed, making it
possible to scale server deployments to high volumes in rapid fashion.
For more information, and to download the SmartStart Scripting Toolkit, refer to
the HP website (http://www.hp.com/servers/sstoolkit).
Diagnostic Tools
55
HP Instant Support Enterprise Edition
ISEE is a proactive remote monitoring and diagnostic tool to help manage your
systems and devices, a feature of HP support. ISEE provides continuous
hardware event monitoring and automated notification to identify and prevent
potential critical problems. Through remote diagnostic scripts and vital system
configuration information collected about your systems, ISEE enables fast
restoration of your systems. Install ISEE on your systems to help mitigate risk
and prevent potential critical problems.
For more information on ISEE, refer to the HP website
(http://www.hp.com/hps/hardware/hw_enterprise.html).
To download HP ISEE, visit the HP website
(http://www.hp.com/hps/hardware/hw_downloads.html).
For installation information, refer to the HP ISEE Client Installation and Upgrade
Guide (ftp://ftp.hp.com/pub/services/hardware/info/isee_client.pdf).
Option ROM Configuration for Arrays
Before installing an operating system, you can use the ORCA utility to create the
first logical drive, assign RAID levels, and establish online spare configurations.
The utility provides support for the following functions:
•
Configuring one or more logical drives using physical drives on one or more
SCSI buses
•
Viewing the current logical drive configuration
•
Deleting a logical drive configuration
If you do not use the utility, ORCA will default to the standard configuration.
For more information regarding array controller configuration, refer to the
controller user guide.
For more information regarding the default configurations that ORCA uses, refer
to the HP ROM-Based Setup Utility User Guide on the Documentation CD.
56
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
HP ROM-Based Setup Utility
RBSU, an embedded configuration utility, performs a wide range of
configuration activities that may include:
•
Configuring system devices and installed options
•
Displaying system information
•
Selecting the primary boot controller
•
Configuring memory options
•
Language selection
For more information on RBSU, refer to the HP ROM-Based Setup Utility User
Guide on the Documentation CD or the HP website
(http://www.hp.com/servers/smartstart).
ROMPaq Utility
Flash ROM enables you to upgrade the firmware (BIOS) with system or option
ROMPaq utilities. To upgrade the BIOS, insert a ROMPaq diskette into the
diskette drive and boot the system.
The ROMPaq utility checks the system and provides a choice (if more than one
exists) of available ROM revisions. This procedure is the same for both system
and option ROMPaq utilities.
For more information about the ROMPaq utility, refer to the HP website
(http://www.hp.com/servers/manage).
System Online ROM Flash Component Utility
The Online ROM Flash Component Utility enables system administrators to
efficiently upgrade system or controller ROM images across a wide range of
servers and array controllers. This tool has the following features:
•
Works offline and online
Diagnostic Tools
•
57
Supports Microsoft® Windows NT®, Windows® 2000, Windows® Server
2003, Novell Netware, and Linux operating systems
IMPORTANT: This utility supports operating systems that may not be
supported by the server. For operating systems supported by the
server, refer to the HP website (http://www.hp.com/go/supportos).
•
Integrates with other software maintenance, deployment, and operating
system tools
•
Automatically checks for hardware, firmware, and operating system
dependencies, and installs only the correct ROM upgrades required by each
target server
To download the tool and for more information, refer to the HP website
(http://h18000.www1.hp.com/support/files/index.html).
Integrated Management Log
The IML records hundreds of events and stores them in an easy-to-view form.
The IML timestamps each event with 1-minute granularity.
You can view recorded events in the IML in several ways, including the
following:
•
From within HP SIM
•
From within Survey Utility
•
From within operating system-specific IML viewers
•
−
For NetWare: IML Viewer
−
For Windows®: IML Viewer
−
For Linux: IML Viewer Application
From within HP Insight Diagnostics
For more information, refer to the Management CD in the HP ProLiant Essentials
Foundation Pack.
58
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Integrated Lights-Out Technology
The iLO subsystem is a standard component of selected ProLiant servers that
provides server health and remote server manageability. The iLO subsystem
includes an intelligent microprocessor, secure memory, and a dedicated network
interface. This design makes iLO independent of the host server and its operating
system. The iLO subsystem provides remote access to any authorized network
client, sends alerts, and provides other server management functions.
Using iLO, you can:
•
Remotely power up, power down, or reboot the host server.
•
Send alerts from iLO regardless of the state of the host server.
•
Access advanced troubleshooting features through the iLO interface.
•
Diagnose iLO using HP SIM through a web browser and SNMP alerting.
For more information about iLO features, refer to the Integrated Lights-Out User
Guide on the Documentation CD or on the HP website
(http://www.hp.com/servers/lights-out).
Automatic Server Recovery
ASR is a feature that causes the system to restart when a catastrophic operating
system error occurs, such as a blue screen, ABEND, or panic. A system fail-safe
timer, the ASR timer, starts when the System Management driver, also known as
the Health Driver, is loaded. When the operating system is functioning properly,
the system periodically resets the timer. However, when the operating system
fails, the timer expires and restarts the server.
ASR increases server availability by restarting the server within a specified time
after a system hang or shutdown. At the same time, the HP SIM console notifies
you by sending a message to a designated pager number that ASR has restarted
the system. You can disable ASR from the HP SIM console or through RBSU.
Diagnostic Tools
59
HP Systems Insight Manager
HP SIM is a web-based application that allows system administrators to
accomplish normal administrative tasks from any remote location, using a web
browser. HP SIM provides device management capabilities that consolidate and
integrate management data from HP and third-party devices.
IMPORTANT: You must install and use HP SIM to benefit from the PreFailure Warranty for processors, hard drives, and memory modules.
For additional information, refer to the Management CD in the HP ProLiant
Essentials Foundation Pack or the HP SIM website
(http://www.hp.com/go/hpsim).
HP Insight Diagnostics
The HP Insight Diagnostics utility displays information about the server
hardware and tests the system to be sure it is operating properly. The utility has
online help and can be accessed using the SmartStart CD. Online Diagnostics for
Microsoft® Windows® is available for download from the HP website
(http://www.hp.com/support).
USB Support
HP provides both standard USB support and legacy USB support. Standard
support is provided by the operating system through the appropriate USB device
drivers. HP provides support for USB devices before the operating system
loading through legacy USB support, which is enabled by default in the system
ROM. HP hardware supports USB version 1.1 or 2.0, depending on the version
of the hardware.
Legacy USB support provides USB functionality in environments where USB
support is normally not available. Specifically, HP provides legacy USB
functionality for:
•
POST
•
RBSU
60
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
•
Diagnostics
•
DOS
•
Operating environments which do not provide native USB support
For more information on ProLiant USB support, refer to the HP website
(http://h18004.www1.hp.com/products/servers/platforms/usb-support.html).
Internal USB Functionality
An internal USB connector is available for use with USB drive keys only. The
internal connector shares the same bus with the front external USB connector,
and connecting a device to both the front internal and front external USB
connectors is not supported. This solution provides for use of a permanent boot
drive from a USB drive key installed in the front internal connector, avoiding
issues of clearance on the front of the rack and physical access to secure data.
For additional security, you can disable the front USB connectors through RBSU.
Disabling external USB ports in RBSU disables both the front external and front
internal USB ports.
61
Server Component Identification
In This Section
Front Panel Components ..............................................................................................................62
Front Panel LEDs and Buttons .....................................................................................................63
Rear Panel Components................................................................................................................64
Rear Panel LEDs and Buttons ......................................................................................................65
System Board Components ..........................................................................................................67
System Maintenance Switch.........................................................................................................68
NMI Switch ..................................................................................................................................68
System Board LEDs .....................................................................................................................69
System LEDs and Internal Health LED Combinations ................................................................70
Internal USB Connector ...............................................................................................................72
SCSI IDs and SATA Device Numbers.........................................................................................73
Hot-Plug SCSI Hard Drive LEDs.................................................................................................73
Hot-Plug SCSI Hard Drive LED Combinations...........................................................................74
Optional Battery-Backed Write Cache Enabler LEDs .................................................................75
Battery-Backed Write Cache Enabler LED Statuses....................................................................76
Fan Module Locations ..................................................................................................................77
Processor Zone Fan Module LED ................................................................................................77
62
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Front Panel Components
Item
Description
1
Diskette drive bay
2
Optical device bay
3
Front USB port
4
Hard drive bay 0
5
Hard drive bay 1
Server Component Identification
Front Panel LEDs and Buttons
Item
Description
Status
1
Power On/Standby button
and system power LED
Green = System is on.
Amber = System is shut down, but power is still applied.
Off = Power cord is not attached, power supply failure has
occurred, no power supplies are installed, facility power is not
available, or the DC-to-DC converter is not installed.
2
UID button/LED
Blue = Identification is activated.
Flashing blue = System is being remotely managed.
Off = Identification is deactivated.
3
Internal health LED
Green = System health is normal.
Amber = System is degraded. To identify the component in a
degraded state, refer to system board LEDs (on page 69).
Red = System critical. To identify the component in a critical
state, refer to system board LEDs (on page 69).
Off = System health is normal (when in standby mode).
4
External health LED
(power supply)
Green = Power supply health is normal.
Amber = Power redundancy failure occurred.
Off = Power redundancy failure has occurred. When the server
is in standby mode, power supply health is normal.
63
64
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Item
Description
Status
5
NIC 1 link/activity LED
Green = Network link exists.
Flashing green = Network link and activity exist.
Off = No link to network exists.
If power is off, view the LEDs on the RJ-45 connector for status
by referring to the rear panel LEDs ("Rear Panel LEDs and
Buttons" on page 65).
6
NIC 2 link/activity LED
Green = Network link exists.
Flashing green = Network link and activity exist.
Off = No link to network exists.
If power is off, the front panel LED is not active. View the LEDs
on the RJ-45 connector for status by referring to the rear panel
LEDs ("Rear Panel LEDs and Buttons" on page 65).
Rear Panel Components
Item
Description
1
PCI-X expansion slot 1, 64-bit/133-MHz 3.3V (optional
PCI Express slot 1, x8)
Server Component Identification
Item
Description
2
PCI-X expansion slot 2, 64-bit/133-MHz 3.3V (optional
PCI Express slot 2, x8)
3
Power supply bay 2
4
Power supply bay 1 (populated)
5
Rear USB connector
6
10/100/1000 NIC 2
7
10/100/1000 NIC 1
8
iLO management port
9
Mouse connector
10
Keyboard connector
11
Video connector
12
Serial connector
Rear Panel LEDs and Buttons
65
66
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Item
Description
Status
1
iLO activity
Green = Activity exists.
Flashing green = Activity exists.
Off = No activity exists.
2
iLO link
Green = Link exists.
Off = No link exists.
3
10/100/1000
Green = Link exists.
NIC 2 activity
Flashing green = Activity exists.
Off = No link exists.
4
5
6
10/100/1000
Green = Link exists.
NIC 2 link
Off = No link exists.
10/100/1000
Green = Link exists.
NIC 1 link
Off = No link exists.
10/100/1000
Green = Activity exists.
NIC 1 activity
Flashing green = Activity exists.
Off = No activity exists.
7
UID button/LED
Blue = Identification is activated.
Flashing blue = System is being managed
remotely.
Off = Identification is deactivated.
Server Component Identification
System Board Components
Item
Description
Item
Description
1
DIMM slots (1-4)
9
Power supply connector
2
NMI switch
10
Power supply signal connector
3
System maintenance
switch (SW2)
11
Smart Array 6i memory
module connector*
4
Processor 1 socket
12
Remote management
connector
5
Processor 2 socket
13
SATA connectors (SATA
model only)
6
Processor zone fan
module connector
14
PCI riser board assembly
connector (for slot 2 riser
board)
7
SCSI backplane
connector*
15
PCI riser board assembly
connector (for slot 1 riser
board)
8
Optical device connector
16
System battery
* For SCSI models only
67
68
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
System Maintenance Switch
Position
Default
Function
S1
Off
Off = iLO security is enabled.
On = iLO security is disabled.
S2
Off
Off = System configuration can be
changed.
On = System configuration is
locked.
S3
Off
Reserved
S4
Off
Reserved
S5
Off
Off = Power-on password is
enabled.
On = Power-on password is
disabled.
S6
Off
Off = No function
On = ROM treats the system
configuration as invalid.
S7, S8
Off, Off
Debug LEDs
NMI Switch
The NMI switch allows administrators to perform a memory dump before
performing a hard reset. Crash dump analysis is an essential part of eliminating
reliability problems, such as hangs or crashes in operating systems, device
drivers, and applications. Many crashes freeze a system, requiring you to do a
hard reset. Resetting the system erases any information that would support root
cause analysis.
Systems running Microsoft® Windows® operating systems experience a blue
screen trap when the operating system crashes. When this happens, Microsoft®
recommends that system administrators perform an NMI event by pressing a
dump switch. The NMI event enables a hung system to become responsive again.
Server Component Identification
System Board LEDs
Item
LED Description
Status
1
DIMM 4B failure
Amber = DIMM has failed.
Off = DIMM is operating normally.
2
DIMM 3B failure
Amber = DIMM has failed.
Off = DIMM is operating normally
3
DIMM 2A failure
Amber = DIMM has failed.
Off = DIMM is operating normally.
4
DIMM 1A failure
Amber = DIMM has failed.
Off = DIMM is operating normally
5
Overtemperature
Amber = System has reached cautionary or
critical temperature level.
Off = Temperature is OK.
6
Processor 1 failure
Amber = Processor has failed.
Off = Processor is operating normally.
7
PPM 1 failure
Amber = PPM has failed.
Off = PPM is operating normally.
69
70
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Item
LED Description
Status
8
PPM 2 failure
Amber = PPM has failed.
Off = PPM is operating normally.
9
Processor 2 failure
Amber = Processor has failed.
Off = Processor is operating normally.
10
11
12
Power supply signal
connector interlock
failure
Amber = Power supply signal cable is not
connected.
Standby power
good
Green = Auxiliary power is applied.
Power supply fan
module failure
Amber = One fan in this module has failed.
Off = Power supply signal cable is
connected.
Off = Auxiliary power is not applied.
Red = Multiple fans in this module have
failed.
Off = All fans in this module are operating
normally.
13
System diagnostic
Refer to the HP Remote Lights-Out Edition II
User Guide on the Documentation CD.
14
Online spare
memory
Amber = Failover has occurred. Online spare
memory is in use.
Green = Online spare memory is enabled,
but not in use.
Off = Online spare memory is disabled.
15
Riser interlock
Amber = PCI riser assembly is not seated.
Off = PCI riser assembly is seated.
System LEDs and Internal Health LED Combinations
When the internal health LED on the front panel illuminates either amber or red,
the server is experiencing a health event. Combinations of illuminated system
LEDs and the internal health LED indicate system status.
Server Component Identification
The front panel health LEDs indicate only the current hardware status. In some
situations, HP SIM may report server status differently than the health LEDs
because the software tracks more system attributes.
System LED and
Color
Internal Health
LED Color
Status
Processor failure,
socket X (Amber)
Red
One or more of the following conditions may exist:
•
Processor in socket X has failed.
•
Processor in socket X failed over to the offline spare.
•
Processor X is not installed in the socket.
•
Processor X is unsupported.
•
ROM detects a failed processor during POST.
Amber
Processor in socket X is in a pre-failure condition.
Processor failure,
both sockets (Amber)
Red
Processor types are mismatched.
PPM failure (Amber)
Red
PPM has failed.
DIMM failure, slot X
(Amber)
Red
•
DIMM in slot X has failed.
•
DIMM in slot X is an unsupported type, and no valid
memory exists in another bank.
•
DIMM in slot X has reached single-bit correctable
error threshold.
•
DIMM in slot X is in a pre-failure condition.
•
DIMM in slot X is an unsupported type, but valid
memory exists in another bank.
Amber
DIMM failure, all slots
in one bank (Amber)
Red
No valid or usable memory is installed in the system.
Overtemperature
(Amber)
Amber
The Health Driver has detected a cautionary temperature
level.
Red
The server has detected a hardware critical temperature
level.
Riser interlock
(Amber)
Red
The PCI riser board assembly is not seated.
Online spare memory
(Amber)
Amber
Bank X failed over to the online spare memory bank.
71
72
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
System LED and
Color
Internal Health
LED Color
Status
Power converter
module interlock
(Amber)
Red
The power converter module is not seated.
Fan module (Amber)
Amber
A redundant fan has failed.
Fan module (Red)
Red
The minimum fan requirements are not being met in one
or more of the fan modules. One or more fans have failed
or are missing.
Power supply signal
interlock (Amber)
Red
The power supply signal cable is not connected to the
system board.
Internal USB Connector
The front internal USB connector is located in the processor zone fan module.
For more information, refer to "Internal USB Functionality (on page 60)."
Server Component Identification
SCSI IDs and SATA Device Numbers
Hot-Plug SCSI Hard Drive LEDs
73
74
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Item
LED Description
Status
1
Activity status
On = Drive activity
Flashing = High activity on the drive or drive
is being configured as part of an array.
Off = No drive activity
2
Online status
On = Drive is part of an array and is
currently working.
Flashing = Drive is actively online.
Off = Drive is offline.
3
Fault status
On = Drive failure
Flashing = Fault-process activity
Off = No fault-process activity
Hot-Plug SCSI Hard Drive LED Combinations
Activity
LED (1)
Online
LED (2)
Fault LED Interpretation
(3)
On, off, or
flashing
On or off
Flashing
On, off, or
flashing
On
On or
flashing
Flashing
A predictive failure alert has been received for this drive.
Replace the drive as soon as possible.
Off
The drive is online and is configured as part of an array.
If the array is configured for fault tolerance and all other drives in the
array are online, and a predictive failure alert is received or a drive
capacity upgrade is in progress, you may replace the drive online.
Off
Do not remove the drive. Removing a drive may terminate the
current operation and cause data loss.
The drive is rebuilding or undergoing capacity expansion.
On
Off
Off
Do not remove the drive.
The drive is being accessed, but (1) it is not configured as part of an
array; (2) it is a replacement drive and rebuild has not yet started; or
(3) it is spinning up during the POST sequence.
Server Component Identification
Activity
LED (1)
Online
LED (2)
Fault LED Interpretation
(3)
Flashing
Flashing
Flashing
75
Do not remove the drive. Removing a drive may cause data loss
in non-fault-tolerant configurations.
Either (1) the drive is part of an array being selected by an array
configuration utility; (2) Drive Identification has been selected in
HP SIM; or (3) drive firmware is being updated.
Off
Off
On
The drive has failed and has been placed offline.
You may replace the drive.
Off
Off
Off
Either (1) the drive is not configured as part of an array; (2) the drive
is configured as part of an array, but it is a replacement drive that is
not being accessed or being rebuilt yet; or (3) the drive is configured
as an online spare.
If the drive is connected to an array controller, you may replace the
drive online.
Optional Battery-Backed Write Cache Enabler LEDs
Item
LED Color
1
Amber
2
Green
76
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
For LED status information, refer to "Battery-Backed Write Cache Enabler LED
Statuses (on page 76)."
Battery-Backed Write Cache Enabler LED Statuses
Server Status
LED Status
Server is on and has normal run Green = On
time
Fast charging
Green = Off
Trickle charging
Amber = On
A short exists in the connection of one or more
of the four button cells within the battery module
Amber = Blinking
An open exists in the circuit between the
positive and negative terminals of the battery
module
Amber = Off
Normal
Server is on and is in the first 30 Green = On
seconds after power up
Amber = On
Server is off and is in data
retention mode
Battery Module Status
Temporary lock-out state; data was lost due to
cable being detached
Amber = Blinking every User data held in write cache is being backed
15 seconds
up
Server Component Identification
Fan Module Locations
Item
Description
1
Power supply zone fan module
2
Processor zone fan module
Processor Zone Fan Module LED
77
78
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Status
Amber = One fan in this module has failed.
Red = Multiple fans in this module have failed.
Off = All fans in this module are operating normally.
For power supply zone fan module LED information, refer to System Board
LEDs (on page 69).
79
Specifications
In This Section
Server Specifications ....................................................................................................................79
Environmental Specifications.......................................................................................................80
Hot-Plug Power Supply Calculations ...........................................................................................80
DDR SDRAM DIMM Specifications...........................................................................................80
1.44-MB Diskette Drive Specifications........................................................................................81
CD-ROM Drive Specifications ....................................................................................................82
Ultra320 SCSI Hard Drive Specifications....................................................................................83
Serial ATA Hard Drive Specifications .........................................................................................83
Server Specifications
Dimension
Specification
Height
4.32 cm (1.70 in)
Depth
69.22 cm (27.25 in)
Width
42.62 cm (16.78 in)
Weight (maximum)
16.78 kg (37 lb)
Weight (no drives installed)
12.47 kg (27.5 lb)
Input requirement
Specification
Rated input voltage
100 VAC to 240 VAC
Rated input frequency
50 Hz to 60 Hz
Rated input current
6.0 A (110 V) to 3.0 A (220 V)
Rated input power
580 W
BTUs per hour
1990
Power supply output
Specification
Rated steady-state power
460 W
80
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Environmental Specifications
Temperature range*
Specification
Operating
10°C to 35°C (50°F to 95°F)
Shipping
-40°C to 70°C (-40°F to 158°F)
Maximum wet bulb temperature 28°C (82.4°F)
Relative humidity
(noncondensing)**
Specification
Operating
10% to 90%
Non-operating
5% to 95%
* All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m
(1.8°F per 1,000 ft) to 3048 m (10,000 ft) is applicable. No direct sunlight allowed.
** Storage maximum humidity of 95% is based on a maximum temperature of 45°C
(113°F). Altitude maximum for storage corresponds to a pressure minimum of 70 KPa.
Hot-Plug Power Supply Calculations
For hot-plug power supply specifications and calculators to determine electrical
and heat loading for the server, refer to the HP Enterprise Configurator website
(http://h30099.www3.hp.com/configurator/).
DDR SDRAM DIMM Specifications
NOTE: Use only 256-, 512-MB, 1-GB, or 2-GB; 72-bit wide; 2.5-V;
PC2700 Registered ECC DDR SDRAM. Use HP DDR SDRAM only.
Item
Description
Size
256 MB, 512 MB, 1 GB, 2 GB
Width
72 bits
Upgrade requirement Any combination of like-paired DDR SDRAM DIMMs that
provide a minimum of 512 MB
Specifications
1.44-MB Diskette Drive Specifications
Item
Description
Dimensions
Height
12.7 mm (0.5 in)
Width
96 mm (3.8 in)
Depth
130 mm (5.1 in)
LEDs (front panel)
Green = On
Read/write capacity per
diskette
High density
1.44 MB
Low density
720 KB
Drives supported
1
Drive height
One-third height
Drive rotation
300 rpm
Transfer rate
High
500 Kb/s
Low
250 Kb/s
Bytes/sector
512
Sectors per track (high/low)
18/9
Tracks per side (high/low)
80/80
Access times
Track-to-track (high/low)
3 ms/6 ms
Average (high/low)
169 ms/94 ms
Setting time
15 ms
Latency average
100 ms
Cylinders (high/low)
80/80
Read/write heads
2
81
82
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
CD-ROM Drive Specifications
Item
Description
Applicable disk
CD-ROM (modes 1 and 2); mixed mode (audio and data combined); CD-DA;
Photo CD (single/multiple-session), CD-XA ready; CDi ready
Capacity
550 MB (mode 1, 12 cm)
640 MB (mode 2, 12 cm)
Block size
2368, 2352 bytes (mode 0)
2352, 2340, 2336, 2048 bytes (mode 1)
2352, 2340, 2336, 2048 bytes (mode 2)
Dimensions
Height
12.7 mm (0.50 in)
Depth
132.08 mm (5.20 in)
Width
132.08 mm (5.20 in)
Weight
0.34 kg (0.75 lb)
Data transfer rate
Sustained
150 KB/s (sustained 1X), 1500/3600 KB/s (10X to 24X)
Burst
16.6 MB/s
Access times (typical)
Full stroke
300 ms
Random
140 ms
Diameter
12 cm, 8 cm (4.70 in, 3.15 in)
Thickness
1.2 mm (0.05 in)
Track pitch
1.6 µm (6.3 × 10-7 in)
Cache/buffer
128 KB
Startup time
< 10 s
Stop time
< 5 s (single); < 30 s (multisession)
Laser parameters
Type
Semiconductor laser GaAs
Specifications
Item
Description
Wave length
700 ± 25 nm
Divergence angle
53.5° ± 1.5°
Output power
0.14 mW
Operating conditions
Temperature
5°C to 45°C (41°F to 118°F)
Humidity
5% to 90%
Ultra320 SCSI Hard Drive Specifications
Item
36.4-GB Ultra320
SCSI Drive
72.8-GB Ultra320
SCSI Drive
72.8-GB Ultra320
SCSI Drive
146.8-GB Ultra320
SCSI Drive
Capacity
36,419.6 MB
72,837.2 MB
72,837.2 MB
146,815.74 MB
Height
1.0 in (One-third
height)
1.0 in (One-third
height)
1.0 in (One-third
height)
One-third, 1.0 in
Width
4.0 in
4.0 in
4.0 in
4.0 in
Interface
Ultra320 SCSI
Ultra320 SCSI
Ultra320 SCSI
Ultra320SCSI
Transfer rate
320 MB/sec
320 MB/sec
320 MB/sec
320 MB/sec
Rotational
speed
15,000 rpm
10,000 rpm
15,000 rpm
10,000 rpm
Bytes per
sector
512
512
512
512
Logical blocks 71,132,000
142,264,000
142,264,000
286,749,488
Operating
temperature
10°C to 35°C
(50°F to 95°F)
10°C to 35°C
(50°F to 95°F)
10°C to 35°C
(50°F to 95°F)
10°C to 35°C
(50°F to 95°F)
Serial ATA Hard Drive Specifications
Item
80-GB SATA Drive
160-GB SATA Drive
250-GB SATA Drive
Capacity
80,000 MB
160,000 MB
250,000 MB
83
84
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
Item
80-GB SATA Drive
160-GB SATA Drive
250-GB SATA Drive
Height
1.028 in
1.028 in
1.028 in
Width
4.0 in
4.0 in
4.0 in
Interface
Serial ATA
Serial ATA
Serial ATA
Transfer rate
1.5 GB/s
1.5 GB/s
1.5 GB/s
Rotational
speed
7,200 rpm
7,200 rpm
7,200 rpm
Bytes per
sector
512
512
512
Logical blocks 156,301,488
312,581,808
488,397,168
Operating
temperature
5°C to 55°C
(41°F to 131°F)
5°C to 55°C
(41°F to 131°F)
5°C to 55°C
(41°F to 131°F)
85
Acronyms and Abbreviations
ABEND
abnormal end
ACU
Array Configuration Utility
ASR
Automatic Server Recovery
BBWC
battery-backed write cache
DDR
double data rate
DU
driver update
EFS
Extended Feature Supplement
IEC
International Electrotechnical Commission
86
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
iLO
Integrated Lights-Out
IML
Integrated Management Log
IPL
initial program load
IRQ
interrupt request
MPS
multi-processor specification
NEMA
National Electrical Manufacturers Association
NFPA
National Fire Protection Association
NIC
network interface controller
NVRAM
non-volatile memory
ORCA
Option ROM Configuration for Arrays
Acronyms and Abbreviations
PCI Express
peripheral component interconnect express
PCI-X
peripheral component interconnect extended
PDU
power distribution unit
POST
Power-On Self-Test
PPM
Processor Power Module
PSP
ProLiant Support Pack
PXE
preboot eXecution environment
RBSU
ROM-Based Setup Utility
RILOE II
Remote Insight Lights-Out Edition II
SATA
serial advanced technology attachment
87
88
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
SCSI
small computer system interface
SDRAM
synchronous dynamic RAM
SIM
Systems Insight Manager
SIMM
single inline memory module
SPM
system power module
SSD
support software diskette
TMRA
recommended ambient operating temperature
UID
unit identification
USB
universal serial bus
VCA
version control agent
Acronyms and Abbreviations
VHDCI
very high density cable interconnect
WOL
Wake-on LAN
89
91
Index
drive LEDs 73, 74
E
A
AC power supply 27
ASR (Automatic Server Recovery) 58, 85
Automatic Server Recovery (ASR) 58
Autorun Menu 53
electrostatic discharge 14
environmental requirements 80
environmental specifications 80
expansion slots 64
extending server from rack 17
external health LED 62, 63
F
B
battery 38, 45, 67, 68
Battery-Backed Write Cache Enabler 38
Battery-Backed Write Cache Enabler LEDs 75,
76
BIOS upgrade 56
blanks 19, 22, 24
blue screen event 68
buttons 61
fan connectors 67
fan LED 73, 77
fan zones 74
fans 77
features 61
flash ROM 56
front panel components 62
front panel LEDs 63
H
C
cable management arm 18
cabling 49
CD ejector assembly 26
CD-ROM drive 25, 82
CD-ROM drive blank 24
component identification 62, 63, 64, 65, 67, 68,
69
components 61
connectors 61
crash dump analysis 68
D
DC power supply 67
diagnostic tools 53, 56, 58
DIMM slot LEDs 73
DIMM slots 67
DIMMs 40
diskette drive 81
hard drive blanks 19
hard drive LEDs 73, 74
hard drives 62, 73, 74, 83
hard drives, determining status of 73
Health Driver 58, 73
health LEDs 63, 73
HP Insight Diagnostics 59
HP ProLiant Essentials Foundation Pack 59
HP Systems Insight Manager, overview 59
I
illustrated parts catalog 7
iLO (Integrated Lights-Out) 58, 64
IML (Integrated Management Log) 57
Insight Diagnostics 59
Instant Support Enterprise Edition 55
Integrated Management Log (IML) 57
internal health LED 62, 63
92
HP ProLiant DL360 Generation 4 Server Maintenance and Service Guide
K
keyboard connector 64
L
laser devices 82
LEDs 61, 63, 65, 69, 70, 72, 73, 74, 77
LEDs, hard drive 73
M
management tools 53
memory 40
memory dump 68
memory slots 67
mouse connector 64
N
network connector LEDs 65
NIC (network interface controller) 86
NIC connectors 64
NIC LEDs 62, 63
NMI switch 68
O
Online ROM Flash Component Utility 56
online spare memory 40
operating system crash 68
Option ROM Configuration for Arrays
(ORCA) 55
ORCA (Option ROM Configuration for
Arrays) 55
overtemperature LED 74
P
PCI riser board 33, 35
power connectors, internal 67
power converter module 36
power converter module cabling 50
power cord connector 68
power LEDs, system 63
Power On/Standby button 16, 62, 63
power requirements 80
power supplies 64, 65, 80
power supply LEDs 65
power supply output 80
power supply signal connector 67
power supply zone fans 28, 77
powering down 16
PPM failure LEDs 74
preparation procedures 15
processor zone fans 29, 77
processors 42, 67
R
RBSU (ROM-Based Setup Utility) 56
rear panel buttons 65
rear panel connectors 64
rear panel LEDs 65
remote support and analysis tools 55
removal and replacement procedures 13
required tools 13
resetting the system 68
RJ-45 connectors 64
RJ-45 network connector LEDs 65
ROM, updating 56
ROMPaq utility 56
S
safety considerations 14
SATA connectors 51, 67
SATA drives 73
SCSI backplane 31
SCSI connectors 67
SCSI IDs 73
serial connector 64, 68
server asset text 47
server setup 14
server warnings and cautions 14
Smart Array 6i memory connector 67
SmartStart Autorun Menu 53
SmartStart Scripting Toolkit 54
SmartStart, overview 53
spare part numbers 7
Index
specifications 79
specifications, server 79, 80, 81, 82, 83
static electricity 14
support packs 53
switches 67
system board 46
system board battery 45
system board components 67
system board LEDs 69, 70
system maintenance switch 68
system power connector 67
system power LED 63
Systems Insight Manager 59
T
telco racks 15
temperature requirements 80
tools 53
U
UID LEDs 16, 62, 63, 64, 65
USB connectors 64
USB support 59, 60
utilities 55, 56, 59
V
VHDCI SCSI connector 64
video connector 64
93
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising