Manual 1 - Tower Hobbies
Instruction Manual
GP
EP
version
version
OUTRAGEOUS
GP/EP Size 50- 60CC ARF
SPECIFICATION
- Wingspan: 2032mm (80 in)
- Length: 1698mm (66.8 in)
- Flying weight: 7.8-8.2 kg
- Wing area: 77.2dm2
- Wing loading: 93g/dm2
- Wing type: Naca airfoils
- Covering type: Genuine ORACOVER®
- Gear type: Plate Aluminum
hi-grade(included)
- Spinner size: Plastic 86mm (included)
- Radio: 6 channel minimum (not included)
- Servo: 6 standard Hi-torque servo: 2 aileron;
2 elevator; 1 rudder; 1 throttle (not included)
- Recommended receiver battery: 4.8-6V /
1200-2000mAh NiMH (not included)
- Servo mount: 21mm x 42 mm
- Propeller: suit with your engine
- Engine: 50- 60cc gas engine (not included)
- Motor: brushless outrunner 2600-3000 W,
190 KV (not included)
- Gravity CG: 115 mm (4.5 in) Back from
the leading edge of the wing, at the fuselage
- Control throw Ailerons: Low: 12mm up/down,
10% expo; High: 14mm up/down, 10% expo
- Control throw Elevators: Low: 12mm up/down,
12% expo; High: 14mm up/down, 12% expo
- Control throw Rudder: Low: 20mm right/left,
15% expo; High: 30mm right/left, 15% expo
- Experience level: Intermediate
- Plane type: Scale Civilian
RECOMMENDED MOTOR AND BATTERY SET UP
- Motor: hacker brushless Q80 (not included)
- Propeller: 22x12 APC E (not included)
- Lipo cell: 12 cells / 5000 – 6000mAh
(not included)
- Esc: 120-160A / HV (not included)
Instruction Manual
OUTRAGEOUS
TABLE OF CONTENTS
Introduction ....................................................1
Installing the tail wheel
.....................................23
Warranty ........................................................2
Installing the fuel tank
......................................25
Disclaimer ......................................................2
Installing the engine
Safety precaution ............................................2
Installing the throttle .........................................29
Important building notes ....................................2
Mounting the cowl
Suggestion .....................................................2
Installing the spinner ........................................32
Flight warnings................................................2
Installing the receiver and battery
Flight warnings................................................3
Installing the switch
Covering tools.................................................3
Installing the electric motor ( ep version )
Adhesives and required tools .............................3
Balancing
Academy of model aeronautics national
Lateral balance ...............................................38
model aircraft safety code..................................3
Control throws ................................................39
Installing the main landing gear ..........................5
Flight preparation pre flight check .......................39
Preparations ...................................................8
For your radio installation
Installing the ailerons
.......................................8
........................................26
...........................................31
.......................33
.........................................33
.............34
......................................................38
Basic connection for airplane
Installing the aileron servos ...............................9
and adjustment of servos ..................................41
Installing the aileron linkages .............................11
Main gear dimensional detail
Secure the wing to the fuselage ..........................13
Tail gear dimensional detail
.............................42
...............................42
..........................13
Decoration .....................................................43
Vertical stabilizer installation ..............................15
Exploded view ................................................44
Installing the rudder servo .................................16
Exploded view ................................................45
Horizontal stabilizer installation
Installing the rudder linkages
.............................18
Installing the elevator servo ...............................19
Installing the elevator linkages
...........................21
INTRODUCTION
Thank you for purchasing Phoenix Model products. With over 20 years experience in production and fly testing,
Phoenix Model is committed to bring the best quality products and good service to customers. Along with a team of
creative engineers and skilled workers, we will always accompany with customers by our great experiences, fully
enthusiasm... which will burn our passion!! Joining with us to explore and conquer challenges in the sky ...
Your satisfaction is our success. Please read through this manual before starting construction.
Academy of Model Aeronautics: If you are not already a member of the AMA, please join! The AMA is the
governing body of model aviation and membership provides liability insurance coverage, protects modelers’
rights and interests and is required to fly at most R/C sites.
Academy of Model Aeronautics
5151 East Memorial Drive Muncie, IN 47302-9252
Tele. (800) 435-9262
Fax (765) 741-0057
Or via the Internet at: http://www.modelaircraft.org
1
Instruction Manual
OUTRAGEOUS
The painted and plastic parts used in this kit are
fuel proof. However, they are not tolerant of many
harsh chemicals including the following: paint thinner,
C/A glue accelerator, C/A glue debonder and
acetone. Do not let these chemicals come in contact
with the colors on the covering and the plastic parts.
WARRANTY
Phoenix Model guarantees the component parts in
this kit to be free from defects in both material and
workmanship at the date of purchase by the
purchaser.
This warranty does not cover cosmetic damage or
damage due to acts of God, accident, misuse,
abuse, negligence, commercial use, or modification
of or to any part of the Product.
This warranty does not cover damage due to
improper installation, operation, maintenance, or
attempted repair by anyone other than Phoenix
Model.
Some parts included in this kit such as the cowl or
wheel pants are made of fiberglass, the fibers of
which may cause eye, skin and respiratory tract
irritation. Never blow into a part to remove fiberglass
dust, as the dust will blow back into your eyes.
Always wear safety goggles, a particle mask and
rubber gloves when grinding, drilling and sanding
fiberglass parts. Vacuum the parts and the work area
thoroughly after working with fiberglass parts.
Further, Phoenix Model reserves the right to change
or modify this warranty without notice.
SUGGESTION
DISCLAIMER
To avoid scratching your new airplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old towel or
brown paper, both to protect the aircraft and to
protect the table. Keep a couple of jars or bowls
handy to hold the small parts after you open the bag.
Read this disclaimer carefully before using this
product. Please strictly follow the instruction manual
to assemble and use this.
In that Phoenix Model has no control over the final
assembly or material used for final assembly, Phoenix
Model is not responsible for loss of use , or other
incidental or consequential damages.
Furthermore, Phoenix Model cannot be held liable for
personal injury or property damage caused by the
use or misuse of Phoenix Model products. By the
act of using the user-assembled products, the user
accepts all resulting liability.
SUGGESTION FOR ENGINE AND SERVO
• ENGINE: DLE 61 RA
• SERVO: Two Options
• Servo Option 1:Sport Performance
Hitec 7985MG Servos may be used for sport flying.
7 - Hitec 7985MG Servos for flight surfaces
1 - Hitec 5625MG Servo for throttle
1 - Hitec 5625MG Servo for valve control
• Servo Option 2: Unlimited Performance
Hitec 7954SH Servos are recommended for
unlimited flying.
7 - Hitec 7954SH Servos for flight surfaces
1 - Hitec 5625MG Servo for throttle
1 - Hitec 5625MG Servo for valve control
SAFETY PRECAUTION
This is not a toy and pilots must be over the age
of 14
Be sure that no other flyers are using your radio
frequency.
Do not smoke near fuel
Store fuel in a cool, dry place, away from children
and pets.
Wear safety glasses.
The glow plug clip must be securely attached to
the glow plug.
Do not flip the propeller with your fingers.
Keep loose clothing and wires away from the
propeller.
Do not start the engine if people are near. Do not
stand in line with the side of the propeller.
Make engine adjustments from behind the propeller
only. Do not reach around the spinning propeller.
Moisture causes damage to electronics. Avoid
water exposure to all equipment not specifically
designed and protected for this purpose.
FLIGHT WARNINGS
IMPORTANT BUILDING NOTES
Please trial fit all the parts. Make sure you have the
correct parts and that they fit and are aligned properly
before gluing! This will assure proper assembly. This
kit is hand made from natural materials, every plane
is unique and minor adjustments may have to be
made. However, you should find the fit superior and
assembly simple.
2
Always operate in open areas, away from factories,
hospitals, schools, buildings and houses etc.
NEVER fly your aircraft close to people or built up
areas.
NEVER fly near power lines, aerials or other
dangerous areas including airports, motorways etc.
NEVER fly in wet conditions or on windy or stormy
days.
ALWAYS adjust the engine from behind the
propeller, and do not allow any part of your body to
be in line with the propeller.
THE PROPELLER IS DANGEROUS Keep fingers,
clothing (ties, shirt sleeves, scarves) or any other
loose objects that could be caught or drawn in,
away from the propeller. Take care at ALL times.
NEVER use damaged or deformed propellers
or spinners.
Keep all onlookers (especially small children and
animals) well back from the area of operation. This
is a flying aircraft, which will cause serious injury in
case of impact with a person or animal.
DO NOT dispose of empty fuel containers on a fire,
this can lead to an explosion.
Instruction Manual
OUTRAGEOUS
FLIGHT WARNINGS
ADHESIVES AND REQUIRED TOOLS
When ready to fly, first extend the transmitter aerial.
Switch on the transmitter.
Switch on the receiver.
Check that the wings are correctly fitted to the
fuselage.
Operate the control sticks on the transmitter and
check that the control surfaces move freely and in
the CORRECT directions.
Check that the transmitter batteries have adequate
power.
ALWAYS take off into the wind.
If the model does not respond correctly to the
controls, land it as soon as possible and correct the
fault.
ALWAYS land the model INTO the wind, this ensures
that the model lands at the slowest possible speed.
Switch off the receiver.
Switch off the transmitter.
Empty the fuel tank after flying, fuel left in the tank
can cause corrosion and lead to engine problems.
Thin CA
30-minute epoxy
6-minute epoxy
Threadlocker thread locking cement
Mixing sticks
Mixing cups (GPMR8056)
Epoxy brushes
Denatured alcohol
Canopy Glue
Felt-tipped pen or pencil
Flat screwdriver
Adjustable wrench
Drill
Hobby knife
Masking tape
Phillips screwdriver (large)
Phillips screwdriver (small)
Ruler
Sandpaper
Soldering iron
Solder
Hex wrench
Drill bit: 1/16-inch (1.5mm), 5/64-inch (2mm),
1/8-inch (3,2mm), 3/16-inch (4,8mm),11/64-inch
(4.5mm), 13/64-inch (5,2mm), 1/4-inch (6,4mm)
COVERING TOOLS
Top Flite® MonoKote® Sealing Iron
Top Flite Hot Sock Iron Cover
Top Flite MonoKote Trim Seal Iron
Top Flite MonoKote Heat Gun
Academy of Model Aeronautics National Model Aircraft Safety Code
Effective January 1, 2014
A. GENERAL: A model aircraft is a non-human-carrying aircraft capable of sustained flight in the atmosphere. It may
not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition.
All model flights must be conducted in accordance with this safety code and anyadditional rules specific to the
flying site.
1. Model aircraft will not be flown:
(a) In a careless or reckless manner.
(b) At a location where model aircraft activities are prohibited.
2. Model aircraft pilots will:
(a) Yield the right of way to all human-carrying aircraft.
(b) See and avoid all aircraft and a spotter must be used when appropriate. (AMA Document #540-D.)
(c) Not fly higher than approximately 400 feet above ground level within three (3) miles of an airport without notifying
the airport operator.
(d) Not interfere with operations and traffic patterns at any airport, heliport or seaplane base except where there is a
mixed use agreement.
(e) Not exceed a takeoff weight, including fuel, of 55 pounds unless in compliance with the AMA Large Model
Airplane program. (AMA Document 520-A.)
(f) Ensure the aircraft is identified with the name and address or AMA number of the owner on the inside or affixed
to the outside of the model aircraft. (This does not apply to model aircraft flown indoors.)
(g) Not operate aircraft with metal-blade propellers or with gaseous boosts except for helicopters operated under the
provisions of AMA Document #555.
(h) Not operate model aircraft while under the influence of alcohol or while using any drug that could adversely affect
the pilot’s ability to safely control the model.
(i) Not operate model aircraft carrying pyrotechnic devices that explode or burn, or any device which propels a
projectile or drops any object that creates a hazard to persons or property.
Exceptions:
• Free Flight fuses or devices that burn producing smoke and are securely attached to the model aircraft during
flight.
• Rocket motors (using solid propellant) up to a G-series size may be used provided they remain attached to the
model during flight. Model rockets may be flown in accordance with the National Model Rocketry Safety Code
but may not be launched from model aircraft.
3
Instruction Manual
OUTRAGEOUS
•
Officially designated AMA Air Show Teams (AST) are authorized to use devices and practices as defined within
the Team AMA Program Document. (AMA Document #718.)
(j) Not operate a turbine-powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document
#510-A.)
3. Model aircraft will not be flown in AMA sanctioned events, air shows or model demonstrations unless:
(a) The aircraft, control system and pilot skills have successfully demonstrated all maneuvers intended or anticipated
prior to the specific event.
(b) An inexperienced pilot is assisted by an experienced pilot.
4. When and where required by rule, helmets must be properly worn and fastened. They must be OSHA, DOT,
ANSI, SNELL or NOCSAE approved or comply with comparable standards.
B. RADIO CONTROL (RC)
1. All pilots shall avoid flying directly over unprotected people, vessels, vehicles or structures and shall avoid
endangerment of life and property of others.
2. A successful radio equipment ground-range check in accordance with manufacturer’s recommendations will be
completed before the first flight of a new or repaired model aircraft.
3. At all flying sites a safety line(s) must be established in front of which all flying takes place. (AMA Document
#706.)
(a) Only personnel associated with flying the model aircraft are allowed at or in front of the safety line.
(b) At air shows or demonstrations, a straight safety line must be established.
(c) An area away from the safety line must be maintained for spectators.
(d) Intentional flying behind the safety line is prohibited.
4. RC model aircraft must use the radio-control frequencies currently allowed by the Federal Communications
Commission (FCC). Only individuals properly licensed by the FCC are authorized to operate equipment on
Amateur Band frequencies.
5. RC model aircraft will not knowingly operate within three (3) miles of any pre-existing flying site without a
frequency-management agreement. (AMA Documents #922 and #923.)
6. With the exception of events flown under official AMA Competition Regulations, excluding takeoff and landing, no
powered model may be flown outdoors closer than 25 feet to any individual, except for the pilot and the pilot's
helper(s) located at the flightline.
7. Under no circumstances may a pilot or other person touch an outdoor model aircraft in flight while it is still under
power, except to divert it from striking an individual.
8. RC night flying requires a lighting system providing the pilot with a clear view of the model’s attitude and
orientation at all times. Hand-held illumination systems are inadequate for night flying operations.
9. The pilot of an RC model aircraft shall:
(a) Maintain control during the entire flight, maintaining visual contact without enhancement other than by corrective
lenses prescribed for the pilot.
(b) Fly using the assistance of a camera or First-Person View (FPV) only in accordance with the procedures outlined
in AMA Document #550.
(c) Fly using the assistance of autopilot or stabilization system only in accordance with the procedures outlined in
AMA Document #560.
C. FREE FLIGHT
1. Must be at least 100 feet downwind of spectators and automobile parking when the model aircraft is launched.
2. Launch area must be clear of all individuals except mechanics, officials, and other fliers.
3. An effective device will be used to extinguish any fuse on the model aircraft after the fuse has completed its
function.
D. CONTROL LINE
1. The complete control system (including the safety thong where applicable) must have an inspection and pull test
prior to flying.
2. The pull test will be in accordance with the current Competition Regulations for the applicable model aircraft
category.
3. Model aircraft not fitting a specific category shall use those pull-test requirements as indicated for Control Line
Precision Aerobatics.
4. The flying area must be clear of all utility wires or poles and a model aircraft will not be flown closer than 50 feet
to any above-ground electric utility lines.
5. The flying area must be clear of all nonessential participants and spectators before the engine is started.
4
Instruction Manual
OUTRAGEOUS
INSTALLING THE MAIN LANDING GEAR
8mm Nut
2
2
4mm Collar
4
8mm Washer
4
4 x 20mm Cap Screw
2
< Main Gear (R) >
4 x 30mm Cap Screw
2
< Left >
4mm Washer
< Main Gear (L) >
< Bomb >
4
4mm Spring Washer
4
4x20mm
4mm
Cut off shaded portion
Assemble left and right
sides the same way
5
4x20mm
4mm
< Right >
Instruction Manual
OUTRAGEOUS
Collar
Washer
Nut
Collar
Nut
Main gear
Collar
Cut off shaded portion
Wheel pant
Apply threadlocker
(screw cement).
Wheel
Assemble left and right
sides the same way
6
Nut
Collar
Nut
Washer
Instruction Manual
OUTRAGEOUS
8mm
8mm
Assemble left and right
sides the same way
7
Instruction Manual
OUTRAGEOUS
PREPARATIONS
Use a covering iron with a covering sock on
high heat to tighten the covering if necessary.
Apply pressure over sheeted areas to
thoroughly bond the covering to the wood.
INSTALLING THE AILERONS
TEMPORARY PIN
TO KEEP HINGE
CENTERED
1. Test fit the ailerons to the wing with the hinges.
If the hinges don’t remain centered, stick a pin
through the middle of the hinge to hold it in
position.
2. Apply six drops of thin CA to the top and bottom
of each hinge. Do not use CA accelerator. After
the CA has fully hardened, test the hinges by
pulling on the aileron.
Main Wing
< Bottom view >
Aileron
8
Instruction Manual
OUTRAGEOUS
Make certain the hinges are adequately secured with glue. If
they come loose in flight accidents may result.
Secure nylon hinges with instant glue, being careful
not to glue the wing and airleron together.
Align the center line of main wing with aileron.
Apply instant glue (CA glue, super glue).
INSTALLING THE AILERON SERVOS
4. Using the thread as a guide and using masking
tape, tape the servo lead to the end of the
thread: carefully pull the thread out. When you
have pulled the servo lead out, remove the
masking tape and the servo lead from the
thread.
1. Install the rubber grommets and brass eyelets
onto the aileron servo.
2. Using a modeling knife, remove the covering
from over the pre-cut servo arm exit hole on the
aileron servo tray / hatch. This hole will allow
the servo arm to pass through when installing
the aileron pushrods.
5. Place the aileron servo tray / hatch into the
servo box on the bottom of the wing and drill
pilot holes through the tray and the servo box
for each of the four mounting screws. Secure
the servo tray in place using the mounting
screws provided .
3. Place the servo into the servo tray. Center the
servo within the tray and drill pilot holes
through the block of wood for each of the four
mounting screws provided with the servo.
6. Repeat step # 2 - # 5 to install the second
aileron servo in the opposite wing half.
Aileron
< Bottom view >
Assemble left and right
sides the same way
9
Instruction Manual
OUTRAGEOUS
Aileron Servo
2mm
1.5mm
2 x 10mm TP Screw
8
1.5mm
Warning!
Set all scerws securely. If they come off during
flight you will lose control of your aircraft!
2x10mm
2x10mm
2x10mm
2x10mm
Pay close attention here
Cut off shaded portion
Must be purchased
separately!
Cut away film only. here
Supplied with the servo
Assemble left and right
sides the same way
Pull out servo cord with string.
10
Instruction Manual
OUTRAGEOUS
INSTALLING THE AILERONs LINKAGES
3 x 12mm Screw
4
3mm Nut
2
2
3mm Nylon Nut
2
2
Aluminum ball
3 x 20mm Cap Screw
4
4
2
3mm Washer
2
3x100mm Push rod
2
3 x 20mm
Cut away film only. here
Cut off shaded portion
Assemble left and right
sides the same way
Pull out servo
cord with string.
11
Instruction Manual
OUTRAGEOUS
3mm
Aluminum ball
3mm
3x12mm
3x12mm
3mm
< Right Wing >
< Left Wing >
Pull out servo
cord with string.
Apply threadlocker
(screw cement).
12
Instruction Manual
OUTRAGEOUS
2. Slide the wings into the fuselage. Once flush adjust
the wing screws as necessary and tighten once in
position.
SECURE The Wing To The Fuselage
Attach the wings to the fuselage and secure the
wing panels.
1. Loosen each screw approximately 4mm. (It is not
necessary, nor recommended, to completely
remove the wing screws.)
Cap screw for main wing fixture
Cut off shaded portion
Assemble left and right
sides the same way
5.
HORIZONTAL STABILIZER INSTALLATION
1. Using a modeling knife, cut away the covering
from the fuselage for the stabilizer and remove it.
2. Remove the covering from the stabilizer.
When cutting through the covering to remove it,
cut with only enough pressure to only cut
through the covering it's self. Cutting into the
balsa structure may weaken it. This could lead
to possible failure during flight.
When you are sure that everything is aligned
correctly, mix up a generous amount of 30 minute
epoxy. Apply a thin layer to the bottom and to the
top of the stabilizer mounting area and to the
stabilizer mounting platform sides in the fuselage.
Insert the stabilizer in place and re-align. Double
check all of your measurements one more time
before the epoxy cures. Remove any excess epoxy
using a paper towel and rubbing alcohol and hold the
stabilizer in place with T-pins or masking tape.
6. After the epoxy has fully cured, remove the masking
tape or T-pins used to hold the stabilizer in place and
carefully inspect the glue joints. Use more epoxy to fill
in any gaps that were not filled previously and clean
up the excess using a paper towel and rubbing
alcohol.
3. Attach the wing to the fuselage as picture.
4. Test the position of the elevator and adjust it as
shown.
7. Repeat step 1 - step 2 from the installing aileron for
the installing elevator.
13
Instruction Manual
OUTRAGEOUS
Secure nylon hinges with instant glue, being
careful horizontal fin and elevator.
Align the center line of horizontal fin with elevator.
Cut off shaded portion
Apply instant glue
(CA glue, super glue).
14
Apply epoxy glue
Instruction Manual
OUTRAGEOUS
VERTICAL STABILIZER INSTALLATION
Installing the rudder using C.A glue as
installing the aileron.
90 Degree
Secure nylon hinges with instant glue, being
careful vertical fin and rudder.
Apply instant glue
(CA glue, super glue).
Align the center line of vertical fin with rudder.
Apply epoxy glue
15
Instruction Manual
OUTRAGEOUS
INSTALLING THE RUDDER SERVO
3mm Nut
1
1. Remove the covering from left size of the
fuselage.
3mm Nylon Nut
2. Install servo to the fuselage as shown.
1
1
3. Repeat these step as installing the aileron
control horn.
Aluminum ball
1
2
3 x 35mm Cap Screw
2
1
3x90mm Push rod
3mm Washer
3 x 12mm Screw
2
1
1
3 x 35mm
3 x 35mm
Pay close attention here
Cut off shaded portion
approx. 13mm
Must be purchased separately!
16
Instruction Manual
OUTRAGEOUS
Set all screws securely. If they
come off during flight you will
lose control of your aircraft!
Must be purchased separately!
17
Instruction Manual
OUTRAGEOUS
INSTALLING THE RUDDER LINKAGES
Repeat these step as installing the aileron
linkages.
3mm
Aluminum ball
3mm
3x12mm
3x12mm
3mm
3mm
3x12mm
Rudder rod
3mm
Aluminum ball
3x12mm
3mm
Apply threadlocker
(screw cement).
18
Instruction Manual
OUTRAGEOUS
INSTALLING THE ELEVATOR SERVO
1. Remove the covering from both size of the
fuselage.
3mm Nut
2
2. Install two servo to the fuselage as shown.
3mm Nylon Nut
3. Repeat these step as installing the aileron
control horn.
2
2
2
3x105mm Push rod
Aluminum ball
3 x 15mm Cap Screw
4
2
3 x 12mm Screw
4
2
4
3mm Washer
2
19
Instruction Manual
OUTRAGEOUS
3 x 15mm
3 x 15mm
Assemble left and right
sides the same way
Cut off shaded portion
Pay close attention here
Must be purchased separately!
20
Instruction Manual
OUTRAGEOUS
INSTALLING THE ELEVATOR LINKAGES
Repeat these step as installing the aileron
linkages.
3mm
Aluminum ball
3mm
3 x 12mm
3 x 12mm
3mm
3mm
3 x 12mm
Aluminum ball
Apply threadlocker
(screw cement).
Assemble left and right
sides the same way
3x12mm
3mm
Must be purchased separately!
21
3mm
Instruction Manual
OUTRAGEOUS
< Elevator Servo (L) >
< Elevator Servo (R) >
Rudder Servo
Assemble left and right
sides the same way
22
Instruction Manual
OUTRAGEOUS
INSTALLING THE Tail wheel
3 x 12mm TP Screw
3x12mm
2
4 x 20mm Cap Screw
2
4mm Spring Washer
2
Spring
2
Tail wheel set
1
1
4x20mm
4mm
Cut off shaded portion
23
Instruction Manual
OUTRAGEOUS
Spring
Spring
Spring
24
Instruction Manual
OUTRAGEOUS
INSTALLING THE Fuel Tank
6. When satisfied with the alignment of the stopper
assembly tighten the 3mm x 20mm machine
screw until the rubber stopper expands and
seals the tank opening. Do not over tighten the
assembly as this could cause the tank to split.
1. The stopper has been pre-assembled at the
factory.
2. Using a modeling knife, cut one length of silicon
fuel line (the length of silicon fuel line is
calculated by how the weighted clunk should
rest about 5mm away from the rear of the tank
and move freely inside the tank). Connect one
end of the line to the weighted clunk and the
other end to the nylon pick up tube in the
stopper.
7. Using a modeling knife, cut 3 lengths of fuel line
. Connect 2 lines to the 2 vent tubes and 1 line
to the fuel pickup tube in the stopper.
8. Feed three lines through the fuel tank
compartment and through the pre-drilled hole in
the firewall. Pull the lines out from behind the
engine, while guiding the fuel tank into place.
Push the fuel tank as far forward as possible,
the front of the tank should just about touch the
back of the firewall.
3. Carefully bend the second nylon tube up at a 45
degree angle (using a cigarette lighter). This
tube will be the vent tube to the muffler.
Blow through one of the lines to ensure the fuel
lines have not become kinked inside the fuel
tank compartment. Air should flow through
easily.
4. Carefully bend the third nylon tube down at a 45
degree angle (using a cigarette lighter). This
tube will be vent tube to the fueling valve.
!
When the stopper assembly is installed in the
tank, the top of the vent tube should rest just
below the top surface of the tank. It should not
touch the top of the tank.
!
5. Test fit the stopper assembly into the tank. It
may be necessary to remove some of the
flashing around the tank opening using a
modeling knife. If flashing is present, make
sure none of it falls into the tank.
Do not secure the tank into place permanently
until after balancing the airplane. You may
need to remove the tank to mount the battery in
the fuel tank compartment.
9. Secure the fuel tank.
Clunks
1
Fuel Tank
Silicone Tube
Zip tie
#9
Foam ring
25
Instruction Manual
OUTRAGEOUS
Fuel Tank
Zip tie
INSTALLING THE ENGINE
Metal kwik link (M2)
2mm
Silicone
2
Silicone
2mm
May be you also need to trim some
wood from the tri-angle wood for
the installation is easy.
Silicone
2
1.7x500mm Push rod
350mm Plastic Pipe
2
1
DLE 61 CC
Must be purchased
separately!
26
Instruction Manual
OUTRAGEOUS
DLE 61 CC
DLE 61 CC
Zip tie
Must be purchased
separately!
27
Instruction Manual
OUTRAGEOUS
DLE 61 CC
DLE
Electronic Ignition System
Zip tie
Foam
m
170m
Bend 900
Choke rod
DLE 61 CC
Must be purchased
separately!
28
Instruction Manual
OUTRAGEOUS
DLE 61 CC
Silicone
Throttle Lever
Choke Lever
Choke rod
Silicone
Zip tie
3. Slide the adjustable metal connector / servo arm
assembly over the plain end of the pushrod wire.
Position the throttle stick and the throttle trim at
their lowest positions.
INSTALLING THE THROTTLE
1. Install one adjustable metal connector through
the third hole out from the center of one servo
arm, enlarge the hole in the servo arm using a
2mm drill bit to accommodate the servo
connector. Remove the excess material from
the arm.
!
4. Manually push the carburator barrel fully closed.
Angle the arm back about 45 degree from center
and attach the servo arm onto the servo. With the
carburator barrel fully closed, tighte the set screw
in the adjustable metal connector.
After installing the adjustable metal connector
apply a small drop of thin C/A to the bottom nut.
This will prevent the connector from loosening
during flight.
5.
2. Plug the throttle servo into the receiver and turn on
the radio system. Check to ensure that the throttle
servo output shaft is moving in the correct
direction. When the throttle stick is moved forward
from idle to full throttle, the throttle barrel should
also open and close using this motion. If not,
reverse the direction of the servo, using the
transmitter.
Connector
1
29
Remove the excess throttle pushrod wire using
wire cutters and install the servo arm retaining
screw.
Instruction Manual
OUTRAGEOUS
4x4mm
Adjust the throttle input (transmitter throttle stick), throttle trim movement and
the carburattor opening to the suitable position and screw in the 4x4mm set screw.
Throttle Servo
Cut off shaded portion
Must be purchased
separately!
Throttle Servo
Apply threadlocker
(screw cement).
Ensure smooth, non-binding
movement when assembling
30
Instruction Manual
< Throttle Idling >
OUTRAGEOUS
< Throttle Hi >
< Throttle Stop >
Throttle position of Tx.
approx. 1mm
Throttle Servo
Carburetor
MOUNTING THE COWL
4. While holding the cowl firmly in position, drill
four 1,6mm pilot holes through both the cowl
and the side edges of the firewall.
1. Remove the muffler and needle valve assembly
from the engine. Slide the fiberglass cowl over
the engine.
5. Using a 3mm drill bit, enlarge the holes in the
cowling.
2. Measure and mark the locations to be cut out
for engine head clearance, needle valve,
muffler. Remove the cowl and make these
cutouts using a rotary tool with a cutting disc
and a rotary sanding drum attachment.
! Enlarging the holes through the cowl will prevent
the fiberglass from splitting when the mounting
screws are installed.
6. Slide the cowl back over the engine and secure it
in place using screws.
3. Slide the cowl back into place. Align the front of
the cowl with the crankshaft of the engine. The
front of the cowl should be positioned so the
crankshaft is in the middle of the precut
opening. Hold the cowl firmly in place using
several pieces of masking tape.
7. Install the muffler. Connect the fuel and pressure
lines to the carburator, muffler and fuel filler
valve. Tighten the screws completely.
Washer
3 x 15mm TP Screw
6
5mm
Trim the cowling so it will
match your engine
Cut off shaded portion
31
Instruction Manual
OUTRAGEOUS
3x15mm
INSTALLING THE SPINNER
Install the spinner back-plate, propeller and
spinner cone.
!
The propeller should not touch any part of the
spinner cone. If it dose, use a sharp modeling
knife and carefully trim away the spinner cone
where the propeller comes in contact with it.
3x12mm TP Screw
4
32
Instruction Manual
Propeller
OUTRAGEOUS
Spinner
Spinner
3x12mm
3x12mm
Use the spacer suitable for a shaft.
Must be purchased
separately!
INSTALLING THE RECEIVER AND BATTERY
INSTALLING THE SWITCH
1. Plug the servo leads and the switch lead into the
receiver. You may want to plug an aileron
extension into the receiver to make plugging in the
aileron servo lead easier when you are installing
the wing. Plug the battery pack lead into the
switch.
1. The switch should be mounted on the fuselage
side, opposite the muffler, close enough to the
receiver so the lead will reach. Use the face plate
of the switch cut out and locate the mounting
holes.
2. Cut out the switch hole using a modeling knife.
Use a 2mm drill bit and drill out the two mounting
holes through the fuselage side.
2. Wrap the receiver and battery pack in the protective
foam to protect them from vibration. Use a rubber
band or masking tape to hold the foam in place.
!
3. Secure the switch in place using the two machine
screws provided with the radio system.
Do not permanently secure the receiver and battery
until after balancing the model.
33
Instruction Manual
Receiver Tape
OUTRAGEOUS
Battery for
Receiver
Foam Pad
Tape
Foam Pad
Tape
Battery for
Engine
Switch
On
On
Off
Off
Must be purchased
separately!
INSTALLING THE ELECTRIC MOTOR ( EP VERSION )
5 x 60mm Cap Screw
5mm Washer
4
5 x 40mm Cap Screw
4
12
5mm Washer
4
12 x 15mm Aluminum
4
5mm Spring Washer
12 x 35mm Aluminum
8
4
5mm Mount Nut
16 x 5mm Aluminum
8
4
34
Foam Pad
Instruction Manual
OUTRAGEOUS
White glue
16x5mm
5mm
5x40mm
12x15mm
5x40mm
Mount Nut
5mm
5mm
5x60mm
5x60mm
Apply threadlocker
(screw cement).
12x35mm
5mm
Must be purchased
separately!
35
Instruction Manual
OUTRAGEOUS
Electric Speed Controller
Velcro
Battery Cord
Battery
Must be purchased
separately!
36
Instruction Manual
3x10mm
OUTRAGEOUS
3x10mm
Battery
< Check the
motor rotation >
Electric Speed Controller
When rotating clock wise, change the
connection of 2 wires.
Motor Lead
37
Instruction Manual
OUTRAGEOUS
Open and close
Top Hatch
LATERAL BALANCE
BALANCING
1. It is critical that your airplane be balanced correctly.
Improper balance will cause your plane to lose
control and crash.
!
After you have balanced a plane on the C.G.
You should laterally balance it. Doing this will
help the airplane track straighter.
1. Turn the airplane upside down. Attach one loop
of heavy string to the engine crankshaft and
one to the tail wheel wire. With the wings level,
carefully lift the airplane by the string. This may
require two people to make it easier.
THE CENTER OF GRAVITY IS LOCATED 115mm
(4.5 in) BACK FROM THE LEADING EDGE OF
THE UPPER WING.
2. Mount the wing to the fuselage. Using a couple of
pieces of masking tape, place them on the bottom
side of the wing 115mm (4.5 in) back from the
leading edge.
2. If one side of the wing fall, that side is heavier
than the opposite. Add small amounts of lead
weight to the bottom side of the lighter wing
half's wing tip. Follow this procedure until the
wing stays level when you lift the airplane.
3. If the nose of the plane falls, the plane is nose
heavy. To correct this first move the battery pack
further back in the fuselage. If this is not possible
or does not correct it, stick small amounts of lead
weight on the fuselage under the horizontal
stabilizer. If the tail of the plane falls, the plane is
tail heavy. To correct this, move the battery and
receiver forward or if this is not possible, stick
weight into the firewall. When balanced correctly,
the airplane should sit level or slightly nose down
when you lift it up with your fingers.
38
Instruction Manual
OUTRAGEOUS
115mm (4.5 in)
CONTROL THROWS
1. We highly recommend setting up a plane using
the control throws listed.
2. The control throws should be measured at the
widest point of each control surface.
3. Check to be sure the control surfaces move in
the correct directions.
LOW RATE
Aileron
Elevator
Rudder
12mm up
12mm up
20mm right
12mm down
12mm down
20mm left
FLIGHT PREPARATION PRE FLIGHT CHECK
HIGH RATE
Aileron
Elevator
Rudder
14mm up
14mm up
30mm right
1. Completely charge your transmitter and receiver
batteries before your first day of flying.
14mm down
14mm down
30mm left
2. Check every bolt and every glue joint in your
plane to ensure that everything is tight and well
bonded.
3. Double check the balance of the airplane
4. Check the control surface
5. Check the receiver antenna . It should be fully
extended and not coiled up inside the fuselage.
6. Properly balance the propeller.
39
Instruction Manual
OUTRAGEOUS
12mm
12mm
Aileron Control
12mm
12mm
Elevator Control
20mm
20mm
Rudder Control
40
Instruction Manual
OUTRAGEOUS
FOR YOUR RADIO INSTALLATION
BASIC CONNECTION FOR AIRPLANE AND ADJUSTMENT OF SERVOS
Example of connection
For more information, refer to radio system instruction manual.
Follow instruction manual of Engine and Battery.
Switch
Battery (Receiver)
Aileron Servo
Aileron Servo
Aileron
Aileron
Receiver
Rudder Servo
Rudder
Engine
Elevator Servo
Elevator
Throttle Servo
Elevator Servo
Elevator
41
Instruction Manual
OUTRAGEOUS
Main Gear Dimensional Detail
AL #1 - 5mm
36.0
21.0
Ø8.0
14.0
8.0
Ø7.0
357.0
TAIL Gear Dimensional Detail
AL #2 - 4mm
137.7
25.0
49.2
3.2
16.0
2.0
9.0
19.0
12.0
17.5
25.0
49.1
30.0
5.0
2.0
42
Instruction Manual
OUTRAGEOUS
DECORATION
< Bottom view >
< Top view >
< Side view >
< Side view >
43
3x12mm
3x12mm
R 86mm
5mm
16x5mm
3x15mm(TP)
5x40mm
12x15mm
5x40mm
2mm
2mm
5mm
2x10mm
4x4mm
5mm
5mm
5mm
#9
12x35mm
5x60mm
4mm
4x30mm
4mm
4x20mm
4x30mm
4x20mm
100mm
100mm
44
Mount Nut
EXPLODED VIEW
3x15mm
3mm
3x15mm
3x12mm
3mm
3x12mm
3x20mm
3mm
3x12mm
3mm
3x12mm
2x10mm(TP)
3x35mm
3mm
3x12mm
3mm
3x12mm
3x12mm
4mm
25mm
4x20mm
3mm
3x12mm
3x20mm
3mm
3x12mm
2x10mm(TP)
45
I/C FLIGHT WARNINGS
Always operate in open areas, away
from factories, hospitals, schools,
buildings and houses etc. NEVER fly
your aircraft close to people or built
up areas.
THE PROPELLER IS DANGEROUS
Keep fingers, clothing (ties, shirt
sleeves, scarves) or any other loose
objects that could be caught or drawn
in, away from the propeller. Take care
at ALL times.
Keep all onlookers (especially small
children and animals) well back from
the area of operation. This is a flying
aircraft, which will cause serious
injury in case of impact with a person
or animal.
NEVER fly near power lines, aerials
or other dangerous areas including
airports, motorways etc.
NEVER use damaged or deformed
propellers or spinners.
NEVER fly in wet conditions or on
windy or stormy days.
ALWAYS adjust the engine from
behind the propeller, and do not allow
any part of your body to be in line
with the propeller.
DO NOT dispose of empty fuel
containers on a fire, this can lead to
an explosion.
I/C FLIGHT GUIDELINES
When ready to fly, first extend the
transmitter aerial.
Switch on the transmitter.
Operate the control sticks on the
transmitter and check that the control
surfaces move freely and in the
CORRECT directions.
ALWAYS land the model INTO the
wind, this ensures that the model lands
at the slowest possible speed.
Check that the transmitter batteries
have adequate power.
Switch off the receiver.
Switch on the receiver.
Check that the wings are correctly
fitted to the fuselage.
ALWAYS take off into the wind.
Switch off the transmitter.
If the model does not respond correctly
to the controls, land it as soon as
possible and correct the fault.
Empty the fuel tank after flying, fuel left
in the tank can cause corrosion and
lead to engine problems.
Made in Vietnam
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising