- Vehicles & accessories
- Motor vehicle electronics
- Radar detectors
- Escort
- Passport 8500ci
- Installation manual
Escort Passport 8500ci Installation manual
Add to my manuals
2 Pages
Escort Passport 8500ci is a high-performance radar and laser detector that provides advanced warning of speed traps and laser guns. It features a compact design, easy installation, and a concealed LED display for discreet alerts. With its long-range detection and superior accuracy, the Passport 8500ci is an invaluable tool for drivers who want to stay informed and protected on the road.
advertisement
PASSPORT 8500ci Installation Manual
A
Front Radar/Laser Receiver
1
Determine the best location for the
Radar/Laser Receiver. The best location is typically under the bumper, or inside the front grill of the vehicle. For the best performance, install the Receiver horizontally, with a clear “view” of the road.
2
Using the built-in mounting holes on the Receiver, or the supplied right-angle mounting bracket, mark the hole locations.
Drill pilot holes in the vehicle if necessary.
3
Mount the Receiver using the supplied hardware. (If right-angle mounting bracket is used, secure the Receiver to the rightangle bracket first, then install bracket with Receiver to the vehicle.)
NOTE:
1. Do not drill holes in the receiver itself.
2. Thoroughly investigate location before drilling any holes.
3. Keep all cables away from moving parts, and hot surfaces (radiator, hoses, etc.).
4. Do not splice cable.
B
Receiver Cable
1
Connect the receiver cable to the receiver.
2
Route cable through the firewall, and secure with zip-ties (included).
3
Route receiver cable into the vehicle’s interior. If there is not a suitable opening, drill a 13/32" or 7/16" hole.
4
Pull cable through firewall, and plug connector into the jack labeled “Antenna” on the Interface.
5
Pull cable through the firewall and seal the hole as needed. Use silicone sealant
(not supplied) if necessary.
C
Display Controller
1
Determine the best location for the
Display Controller in the vehicle’s interior.
(Consult customer if necessary.)
NOTE:
1. Only drill hole in firewall after thoroughly investigating location first, ensuring no other wires, hoses, etc. will be damaged.
2. Keep all cables away from moving parts, and hot surfaces (radiator, hoses, etc.).
3. Do not splice cable.
2
Remove paper backing on the backside of the display and apply to a clean dry surface.
3
Route display cable and plug into jack marked “Display” on the Interface.
NOTE:
1. Make certain that the Display is clearly visible from the driver’s position, and that the controls can be easily accessed without interfering with normal driving.
A
B
D
12 Volt
Power Line
±
E
Interior of Vehicle
C
A
D
Interface
1
Install Interface under the dash using supplied zip-ties. DO NOT MOUNT IN
ENGINE COMPARTMENT.
2
Connect black wire (–) to ground, and red-striped wire (+) to a switched 12-volt supply. (If PASSPORT is left in the “on” position, it will automatically power on and off with the ignition). Use blue 3M connector (provided) to tap into existing circuit if needed.
3
Receiver and Display Controller plug into the Interface. Be sure to plug all cables into the correct jacks.
E
Concealed LED Display (Optional)
F
TEST
If a more discreet display is preferred the included LED can be installed:
1
Drill a 1/4" hole, and install the LED clip.
2
Snap LED into clip from behind.
3
Plug the modular connector into
PASSPORT’s Interface marked “LED.”
After all components are installed correctly:
1
Turn vehicle’s ignition to the “on” position.
2
Turn PASSPORT on by pressing the power button located on the front of the Display Controller.
3
PASSPORT will cycle through a short startup sequence.
4
If any error messages come up, see the
Owner’s Manual for details.
R O T C E T E D • Y T al
E anu
F n M
A atio
S tall Ins
• R E S A L • R A D A R d.
le al st In . sy Ea . le mp Si
Read This First
Important Notes
Please read both sides of these instructions before starting your installation.
Then before installing the other components, plug all of them into the Interface and power up the unit to confirm proper operation.
For the easiest trouble-free installation, install the Interface first, and wire it to a 12-volt switched circuit.
N O I T C E T O R P D E L L A T S N I K C I U Q
12-volt installation
experience is
suggested
1
Installation of this system requires some experience and expertise in automotive electronics. Car Audio specialists and many new car dealers can install this for you.
3
If your vehicle is damaged during installation, its safety systems may be compromised and could cause personal injury or property damage.
2
If you choose to install it yourself without expertise in automotive electronics, please note that it can cause personal injury or damage to your vehicle.
4
Improper installation may also void PASSPORT’s warranty.
PASSPORT 8500ci Comes Complete
Front Radar/Laser Receiver Miniature Display Controller
• Miniature weather-proof Radar/Laser
Receiver
• Display Controller mounts easily to
instrument pod, dashboard or
console
• Universal mounting bracket with
stainless steel hardware • Optional hidden display included
• Built-in 16 foot shielded cable with
water proof connector
• 12 nylon wire ties to secure cable
Interface
• Central module connects to
switched 12-volt power and ground
• All components plug directly in
using modular connections
• 3M connector taps into existing
vehicle wiring
Documentation
• Comprehensive Owner’s Manual
• Installation Manual
Built-in Diagnostics
• Confirms all components are
operational
• Fully compatible with Laser Shifters
Performance
Warning
To get the best possible performance, installation of the
Radar/Laser receiver is critical.
Although radar signals will pass through some materials, including plastic, laser signals will not. For this reason the receiver must have a clear view of the road in order to work properly.
NOTE: INSTALL THE RECEIVER
HORIZONTALLY AND LEVEL,
WITH A CLEAR VIEW OF THE
ROAD.
ESCORT Inc.
5440 West Chester Road
West Chester OH 45069
Service 800.543.1608
www.EscortRadar.com
©2011 ESCORT Inc. Escort®, Passport®, SmartShield®, AutoSensitivity™, SpecDisplay™, and ExpertMeter™ are trademarks of ESCORT Inc.
SWS is trademark of SWS, L.C. Features, specifications and prices subject to change without notice.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project