Models UT130, UT150/UT152/UT155 Temperature Controllers

Models UT130, UT150/UT152/UT155 Temperature Controllers
<<Contents>> <<Index>>
General
Specifications
Models
UT130, UT150/UT152/UT155
Temperature Controllers
GS 05C01E02-01E
■ General
UT100 series temperature controllers provide only the
functions and size you require for your application. 1/16,
1/8 and 1/4 DIN sizes are available. Easy-to-read displays
show input and the setpoint. T/C or RTD inputs are
standard and the output type is selectable: ON/OFF,
voltage pulse or DC current. The controllers operate in an
Automatic mode only. Optional alarm contact outputs,
retransmission output, contact input setpoint selection and
RS485 communication are available. Each features dynamic
self-tunig function for easy start up. Super Control fuzzy
logic for overshoot suppression is a proven champion.
■ Model and Suffix Codes
Model
Suffix code
UT130
Description
Temperature controller
Option
/RS
/V24
Note1:/AL option cannot be specified when /HBA option is specified. /HBA option already includes the /AL
option.
Note2:/HBA option cannot be specifed at the same time.
Note3:When specifying the /RS option, be sure to order the required number of copies of Communication
Functions Instruction Manual separeately. You will not be supplied and instruction manual just
because you order for the /RS option.
Model
Suffix code
Description
UT150
UT152
UT155
Temperature controller
–R
Control output for standard–V
type (or for heating)
–A
Relay output (time-proportional PID or on/off control)
Voltage pulse output (time-proportional PID)
4 to 20mA output (continuous PID) (Note1)
Control output for cooling
N
R
V
A
No cooling output (standard type)
Relay output (time-proportional PID or on/off control)
Voltage pulse output (time-proportional PID)
4 to 20mA output (continuous PID)
/AL
/HBA
Option
/EX
/RET
/RS
/V24
Alarm outputs (2 points) (Note2)
Heater disconnection alarm
(includes optional /AL function) (Note1) (Note2) (Note3)
SP1/SP2 switching, starting of timer, and RUN/STOP
switching by external contacts (Note4)
PV retransmission output in 4 to 20mA (Note3)
Communication function (Note4) (Note5)
Power Supply 24V DC / 24V AC
Note1:/HBA option cannot be specifed when 4 to 20 mA output (heating-side) is specifed.
Note2:/AL option cannot be specifed when /HBA option is specifed.
/HBA option already includes the /AL option.
Note3:/HBA option and /RET option cannot be specifed at the same time.
Note4:/EX option and /RS option cannot be specifed at the same time.(model UT150 only)
Note5:/EX option includes contact input 1 (for switching between the SP1 and SP2 target setpoints using
external contacts) and contact input 2 (for enabling the timer).
Note6:When specifying the /RS option, be sure to order the required number of copies of Communication
Functions Instruction Manual separeately. You will not be supplied and instruction manual just
because you order for the /RS option.
■ Measured Value Input
The UT100 series allows you to freely change the input type
by software.
Input Type
K
Thermocouple
/AL
/HBA
No cooling output (standard type)
Relay output (time-proportional PID or on/off control)
Voltage pulse output (time-proportional PID)
Alarm outputs (2 points) (Note1)
Heater disconnection alarm
(includes optional /AL function) (Note1) (Note2)
Communication function (Note2) (Note3)
Power Supply 24V DC / 24V AC
J
T
E
L
U
Pt100
RTD
Control output for cooling
JPt100
˚C
0 to 600˚C
˚C
-199 to 200˚C
-199 to 999˚C
˚C
-199 to 999˚C
˚C
-199 to 400˚C
-199 to 850˚C
˚C
-199 to 200˚C
C
-199 to 500˚C
°F)
Range Code
1
2
3
4
5
6
7
12
13
15
16
17
18
19
F
32 to 999 F
-199 to 400˚F
-199 to 999 F
-199 to 999 F
-199 to 750˚F
-199 to 999 F
-199 to 400 F
-199 to 999 F
Range Code
31
32
33
34
35
36
37
42
43
45
46
47
48
Table 2.UT150/152/155 Measured Input Ranges
Input Type
Thermocouple
N
R
V
RTD
Relay output (time-proportional PID or on/off control)
Voltage pulse output (time-proportional PID)
–R
–V
DC voltage
Control output for standard
type (or for heating)
Range(°C)
K
˚
0.0 to 600.0˚C
J
˚
-199.9 to 400.0˚C
-199.9 to 999.9˚
˚
0 to 1700˚C
T
E
R
S
B
N
L
U
Platinel 2
-199.9 to 900.0˚C
-199.9 to 400.0˚C
0 to 1390˚
˚
0.0 to 400.0˚C
Pt100
-199.9 to 200.0˚
˚
JPt100
-199.9 to 500.0˚C
0 to100mV
0.0 to 100.0
0 to 5 V 0.000 to 5.000
Note
1 to 5 V
0 to 10 V 0.00 to 10.00
Range Code(°C)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
°F)
Range(°F)
˚F
32.0 to 999.9˚F
32.0 to 750.0 F
-300.0 to 750.0˚F
-300.0 to 1800.0˚F
32 to 3100
32 to 3100˚F
32 to 3200 F
-300 to 1600˚F
-300 to 750˚F
32 to 2500 F
32.0 to 750.0˚F
-300 to 400 F
F
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
4 range.
-1999 to 9999, -199.9 to 999.9,
-199.99 to 99.99, -1.999 to 9.999
GS 05C01E02-01E
© Copyright Dec. 2000 (MC)
5th Edition Jun. 2013 (KP)
2
<<Contents>> <<Index>>
■ Hardware Specifications
Measured Value (PV) Input
Alarm Functions
Power Supply and Isolation
Input: 1 point
Input type: Universal; can be selected by soft ware
Input accuracy (at 23±2˚C ambient temperature)
Thermocouple: ±2˚C
However,
±4˚C for thermocouple input-200 to -100˚C
±3˚C for thermocouple input-100 to 0˚C
±5˚C for type R and S (±9˚C for 0 to 500˚C)
±9˚C for type B (accuracy is not guaranteed for 0 to 400˚C)
RTD: ±1˚C ±1digit
Voltage(mV, V)±0.3%
Sampling period for measured value input: 500 ms
Burn-out detection: Functions for thermocouple or RTD
input (burn-out upscale only; can not be switched off)
Input resistance:
1 MΩ or greater for thermocouple or DC mV input
Approx. 1 MΩ for DC V input
Maximum allowable signal source resistance:
250 Ω for thermocouple or DC mV input 2 kΩ for DC V
input
Effect of signal source's resistance:Less than whichever
is greater, ±0.2 µV/1Ω or ±0.01% / 100Ω
Maximum allowable wiring resistance for RTD input:
10 Ω/wire (The resistance values of three wires must be
the same.)
Effect of wiring resistance: ±0.2˚C / 10Ω maximum
Allowable input voltage:
±10 V DC for thermocouple or DC mV input
±20 V DC for DC V input
Noise rejection ratio (50/60Hz)
Normal mode noise: Min. 40 dB
Common mode noise: Min. 120 dB
(Min. 90 dB for DC V input)
Error of reference junction compensation:
±1.5˚C (at 15-35˚C)
±2.0˚C (at 0-50˚C)
The reference junction compensation cannot be
switched off.
Applicable Standards:
Thermocouple and resistance temperature detector
JIS/IEC/DIN (ITS90)
Response time: 2 second or less, 63% (10 - 90%)
(The time required for transmission output to reach 63%
of the maximum excursion when PV abruptly changes
from 10% to 90%)
Alarm Functions
(Option Code /AL or /HBA)
Alarm types: 22 types (Waiting action can be set by
software):
PVhigh limit, PV low limit, Deviation high limit, Devia
tion low limit, De-energized on deviation high limit,
De-energized on deviation low limit, Deviation high
and low limits, High and low limits within deviation,
De-energized on PV high limit, De-energized on PV
low limit, self-diagnostic alarm, FAIL output
Alarm output: 2 relay contacts
Relay contact capacity: 1 A at 240 V AC or
1 A at 30 V DC (with resistance load)
Power Supply (Common for All Models)
Control Output
Output: 1 point (for standard type ) or
2 points (for heating/cooling type)
Output type:
Choose one from (1) to (3) below:
(1) Relay contact output
Contact capacity: 3 A at 240 V AC or 3 A at 30 V DC
(with resistance load)
Note : The control output realy cannot be replaced by users
(2) Voltage pulse output
On voltage:12 to 18 V DC
Off voltage:0.1 V DC or less
load resistance:
600 Ω or greater
short-circuit current:
approx. 30 mA
(3) Current output
Output signal: 4 to 20 mA
Maximum load resistance: 600 Ω
Output accuracy: ±0.3% of span
(at 23 ±2˚C ambient temperature)
Display
Measured value and setpoint display:
[UT150/UT152/UT155]
4-digit, 7-segment LED display
[UT130]
3-digit, 7-segment LED display
Switchs between SP and PV display.
Character height: See the table below.
PV display
(mm)
SP display
(mm)
UT130
UT150
UT152
UT155
17.5
13.5
13.5
20.0
N/A
9.0
9.0
9.5
Status indicator lamps: LEDs
Retransmission Output
The retransmission output is provided only when the /RET
option is specified, but is not available for the UT130 or a
heating/cooling type.
Output signal: PV(measured value) in 4 to 20 mA DC
Maximum load resistance: 600 Ω
Output accuracy: ±0.3% of span (at 23 ±2˚C ambient
temperature)
Contact Inputs
The contact inputs are provided only when the /EX option
is specified, but are not available for the UT130.
Functions:
(1) Switching over two setpoints (SP1 and SP2)
(2) Starting a timer(See the following "Alarm Functions.")
(3) RUN/STOP switching
Specify two functions from the three functions using
parameter DIS.
Input: 2 points (with the shared common terminal)
Input type: Non-voltage contact or transistor contact
input
Contact capacity: At least 12 V, 10 mA
On/off judgment: On state for 1kΩ or less;
Off state for 20 kΩ or greater
Heater Disconnection Alarm Function
(Option Code /HBA)
The heater disconnection alarm is available when timeproportional PID control or on/off control is selected.
Heater current setting range: 1 to 80 A
Alarm output: 1 relay contact (The terminals are the
same as those of the /AL option.)
On time of burn-out detection: Min. 0.2 second
Sensor: CTL-6-S-H or CTL-12-S36-8 (URD Co. Ltd.)
To be purchased separately.
Timer Function (Option Code /EX/AL or /EX/HBA)
The output contact status changes when the preset
time has passed since "TMR" contact turned on. The
contact action can be selected by software from:
(1) Make contact - the contact closes upon time-up.
(2) Break - the contact opens upon time-up.
Input contact type: See "Contact Inputs" above.
Communication Function
The communication function is provided only when the
/RS option is specified.
Communication Protocol
Personal computer link: Used for communication
with a personal computer, or UT link module of the
FA-M3 controller (from Yokogawa Electric Corpora
tion).
Ladder communication: Used for communication
with a ladder communication module of the FA-M3,
or a programmable controller of other manufacturers.
MODBUS communication: Used for communication
with equipment featuring the MODBUS protocol.
Communication Interface
Applicable standards: Complies with EIA RS-485
Number of controllers that can be connected:
Up to 31
Maximum communication distance:1,200 m
Communication method: Two-wire half-duplex, startstop synchronigation, non-procedural
Baud rate: 2400, 4800, or 9600 bps
Safety and EMC Standards
Safety:
Compliant with IEC/EN61010-1 (CE), IEC/EN61010-2030 (CE), approved by CAN/CSA C22.2 No.61010-1
(CSA), approved by UL61010-1.
Installation category: II, Pollution degree: 2
Measurement category: I (CAT I) (UL, CSA)
O (Other) (CE)
Rated measurement input voltage: Max. 10 V DC
Rated transient overvoltage: 1500 V (*)
* This is a reference safety standard value for measurement category I of IEC/EN/CSA/UL61010-1. This
value is not necessarily a guarantee of instrument
performance.
EMC standards: Complies with EN61326,
EN61000-3-2, EN61000-3-3 and EN55011 (CE).
Class A Group 1.
All wires except those for the power supply and relay
contact output terminals are shielded.
During test, the controller continues to operate with
the measurement accuracy within ±20% of the
range.
KC marking:
Electromagnetic wave interference prevention
standard, electromagnetic wave protection standard
compliance
Construction, Mounting, and Wiring
Construction: Dust-proof and Drip-proof front panel
conforming to IP65 [Models UT130/UT150] and IP55
[Models UT152/UT155].
For side-by-side close installation, the controller loses
its drip-proof protection.
Casing: ABS resin and polycarbonate
Case color: Black
Mounting: Flush panel mounting
Terminals: Screw terminals
External dimensions: Refer to P.3.
Weight: UT130/150:Approx.200g
UT152
:Approx.300g
UT155
:Approx.400g
Panel cutout dimensions: Refer to P.4.
All Rights Reserved. Copyright © 2000, Yokogawa Electric Corporation
Power supply
Voltage
Rated at 100-240 V AC
24 V AC/DC when "/ V24" is specified
Frequency
50 or 60 Hz
Maximum power consumption
8 VA maximum(4W maximum)
when"/V24" is specified : 3W maximum
Memory
Non-volatile memory
Withstanding
voltage
Between primary terminals
and secondary terminals
(See Notes 1 and 3.)
Insulation
resistance
Between primary terminals
and secondary terminals
(See Notes 1 and 3.)
CE: 3000V AC for 1 minute
(Between relay
terminals and
secondary terminals
1500V AC for 1 minute)
UL/CSA:1500V AC for 1
minute (Note 2)
20M Ω or more at
500 V DC
Note 1 : The primary terminals are the power supply terminals and relay output terminals. The secondary terminals are the analog input and output terminals, the voltage
pulse output terminals, and the contact input terminals.
Note 2 : The withstanding voltage is specified as 2300 V
AC per minute to provide a margin of safety.
Note 3 : 24V power supply is the secondary terminal.
Isolation
The bold lines below indicate reinforced insulation, and
the broken line indicates functional insulation. In case of
CE conformity, alternate long and short dash line indicates basic insulation.
Power supply terminals
(100-240V AC)
Power Supply
24V DC/24V AC
Control output
terminals: relay
contacts
Measured value input terminals
CT input terminals for /HBA
2 input terminals for /EX
(Note 1)
Internal circuit (Note 2)
Alarm output terminals
(2 relay contacts)
Control output terminals:
4-20 mA DC output or
voltage pulse (Note 3)
Retransmission output
terminals: 4-20 mA (Note 4)
RS-485 terminals for /RS
Note 1: The /EX option is not available for the UT130.
Note 2: Neither the measured value input terminals, CT input terminals for
the /HBA option, nor input terminals for the /EX option are isolated from the
internal circuit.
Note 3: The UT130 does not have the 4 to 20 mA DC output.
Note 4: The /RET option is not available for the UT130.
Environmental Conditions
Normal Operating Conditions
Warm-up time: At least 30 minutes
Ambient temperature: 0 to 50˚C (0 to 40˚C when
mounted side-by-side)
Rate of change of temperature: 10˚C/h or less
Ambient humidity: 20 to 90% RH (no conden sation allowed)
Magnetic field: 400 A/m or less
Continuous vibrations of 5 to 14 Hz:
Amplitude of 1.2 mm or less
Continuous vibrations of 14 to 150 Hz:
4.9 m/s2 (0.5G) or less
Short-period vibrations: 14.7 m/s2 (1.5G) for
15 seconds or less
Shock: 98 m/s2 (10G) for 11 milliseconds or less
Mounting angle: Upward incline of up to 30 degrees;
downward incline is not allowed.
Altitude: 2000m or less above sea level
Maximum Effects from Operating Conditions
(1) Temperature effects
Thermocouple, DC mV and DC V input:
±2 µV/˚C or ±0.02% of F.S. /˚C, whichever is the larger
Resistance temperature detector:
±0.05˚C/˚C or less
Analog output: ±0.05% of F.S./˚C
(2) Effect from fluctuation of power supply voltage (within
rated voltage range)
Analog input: ±0.2 µV/V or ±0.002% of F.S./V,
whichever is the larger
Analog output: ±0.05% of F.S./V
Transportation and Storage Conditions
Temperature: -25 to 70˚C
Humidity: 5 to 95% RH (no condensation allowed)
Shock: Package drop height 90 cm (when packed in the
dedicated package)
GS 05C01E02-01E
5th Edition Jun. 28, 2013-00
3
<<Contents>> <<Index>>
■ Function Block Diagram
External Contact Inputs (/EX)
Heater Current Detection Input (/HBA)
In this block diagram of a UT100
series controller, the shaded
DI1
DI2
CT
Measured Value Input
area functions are featured in all
the UT100 series controllers
Input Processing
Specify
Heater
•SP1/SP2
using
Disconnection
including the UT130; the white
•
parameters
Alarm
•RUN/STOP
area functions are featured in
Bias Calculation
SP1 SP2
the UT150, UT152, and UT155
controllers only.
Rate-of-change Limiter
First Order Lag
When ordering, please specify
the model, suffix, and option
codes according to the
Super Calculation
UT130:3digits, UT15 :4digits
functions required.
UT130:3digits, UT15 :4digits
SP Indication
PV Indication
PID Control
Calculation
Self-tuning
Calculation
Retransmission
Scaling
Retransmission
Output
(/RET)
Alarm Outputs (/AL or /HBA)
Relay Output
Voltage
Pulse Output
4-20 mA
Output
Control Output
(Heating-side Control output for Heating/Cooling Control)
Relay Output
Voltage
Pulse Output
4-20 mA
Output
AL1
AL2
Cooling-side Control Output
for Heating/Cooling Control
■ External Dimensions
UT130
30
48
Mounting Bracket
Max. 44.8 (1.76)
UT150
Terminal Cover
48
100
30
48
Max. 44.8
12
Unit: mm
Max. 47.8 (1.88)
Panel thickness
1 to 10
Panel thickness
Mounting Bracket
Max. 61
100
Max. 44.8
12
Max. 61
48
Max. 47.8
Max. 44.8
Unit: mm
Terminal Cover
1 to 10
Normal Allowable Deviation=± (Value of JIS B 0401-1999 tolerance grade IT18) /2
All Rights Reserved. Copyright © 2000, Yokogawa Electric Corporation
GS 05C01E02-01E
5th Edition Jun. 28, 2013-00
4
<<Contents>> <<Index>>
■ External Dimensions
UT152
30
96
Max. 91.8
100
Panel thickness
1 to 10
Mounting Bracket
11
Unit: mm
30
100
96
Max. 91.8
96
Terminal Cover
Max. 91.8
1-1051-6041-5031-4021-3011-20
UT155
Max. 112
11
Panel thickness
1 to 10
Mounting Bracket
Max. 112
48
Max. 44.6
1-1021-301-20
Unit: mm
Terminal Cover
Normal Allowable Deviation=± (Value of JIS B 0401-1999 tolerance grade IT18) /2
■ Panel Cutout Dimensions
UT130 and UT150
UT152
General
Mounting
UT155
Unit: mm
Min. 117
General
Mounting
Side-by-side
Close Mounting
(25)
45
+
0
92
45
+0.8
0
+0.6
{(N-1)×48+92} 0
N is the number of controllers.
If N > 5, then measure the actual length.
N is the number of controllers.
If N ≥ 5, then measure the actual length.
All Rights Reserved. Copyright © 2000, Yokogawa Electric Corporation
Min. 145
+0.8
0
92
Side-by-side
Close Mounting
(25)
92
{(N-1)×
0
0
+0.8
0
+0.6
0
92
+0.6
0
+0.6
0
{(N-1)×
45
(53)
92
(25)
(53)
+0.8
0
45
+0.6
0
Min. 70
(25)
Min. 70
Side-by-side
Close Mounting
Unit: mm
Min. 70
Min. 145
General
Mounting
Unit: mm
N is the number of controllers.
If N ≥ 5, then measure the actual length.
GS 05C01E02-01E
5th Edition Jun. 28, 2013-00
5
<<Contents>> <<Index>>
UT130 Terminal Arrangement
Measured Value (PV) Input
Heater Current Detection Input
Universal input-selectable input type
1
CT
2
(Note 1)
When "/HBA" is specified
Cooling-side Control Output
11
ALM2
12
ALM1
6
13
COM
7
b
8
A
TC Input
RTD Input
When "/AL" or
"/HBA" is specified
B
(for heating/cooling type only)
Voltage Pulse Output
1
11
6
+
2
1
12
7
3
1
13
8
NO
1
1
--
COM
2
4
14
L
9
9
10
N
9
When "/24V"
is specified
100-240V AC
5
Specify one for the output signal type.
10
Control-side Output
(heating-side output for heating/cooling type)
RS-485
Heater Current Detection Input
Voltage Pulse Output
3
3
CT
4
When "/HBA" is specified
NO
14
15
COM
15
RSA(-)
5 SG (Note 2)
(Note 1), (Note 2)
14
When /RS is specified
--
Specify one for the output signal type.
Note 1: The heater current detection input terminals (option code:/HBA)are defined as terminals 1 and 2 for a standard type and as terminals 3 and 4 for a heating/cooling type.
Note 2:For a heating/cooling model, you are not allowed to specify both the/HBA and/RS options at the same time.
UT150 Terminal Arrangement
Retransmission Output
Heater Current Detection Input
Measured Value (PV) Input
Alarm outputs
Universal input-selectable input type
+
1
TC Input
1
CT
--
2
When "/RET" is specified
(Note 1)
DC mV or V Input
ALM1
13
(Note 1)
When "/HBA" is specified
7
+
8
--
COM
When /AL or "/HBA" is
specified
6
B
7
b
8
A
7
+
8
--
(for heating/cooling type only)
Relay Contact Output
4 to 20 mA DC Output
1
NO
1
+
1
+
2
COM
2
--
2
--
1
11
6
Power Supply
7
L
9
9
+
10
--
8
24V AC/DC
/
4
14
9
5
15
10
10
N
is specified
Specify one for the output signal type.
Control Output
(heating-side output for heating/cooling type)
Heater Current Detection Input
RS-485
Parameter DIS
External Contact Inputs
0
3 RSB(+)
3
1
Relay Contact Output Voltage Pulse Output 4 to 20 mA DC Output
2
RUN/STOP
STOP when
3
14
NO
14
+
14
+
15
COM
15
--
15
--
CT
4
COM
(Note 1)
SP2
DI=ON
When "/HBA" is specified
DI=ON
DI=ON
Specify one for the output signal type.
When "/EX" is specified
Note 1:The heater current detection input terminals(option code:/HBA)are defined as terminals 1 and 2 for a standard model, and as terminals 3 and 4 for a heating/cooling model.
When the / RET option is specified, these terminals are defined as terminals 3 and 4.
UT152/UT155 Terminal Arrangement
The terminal arrangements of the
UT152 and UT155 are the same.
When "/EX" is specified
External Contact Inputs
TMR STOP
0
1
2
TC Input
21
Heater Current Detection Input
22
24
RS-485
23
11 B
12
+
13
--
12 b
COM
--
CT
26 RSB(+)
DC mV or V Input
STOP when
DI=ON
SP2 STOP
13 A
25
11
27 RSA(-)
When "/HBA" is specified
28 SG
22
2
12
23
2
13
14
When "/RS" is specified
25
2
15
26
16
(for only heating/cooling control type)
30
COM
29
+
+
--
--
18
Relay Contact Output Voltage Pulse Output 4 to 20 mA DC Output
NO
NO
17
7
Cooling-side Control Output
29
Control Output
+
29
+
--
30
--
29
19
9
30
3
20
Specify one for the output signal type.
Alarm Outputs
ALM2
L
19
Specify one for the output signal type.
30
--
When "/RET" is specified
All Rights Reserved. Copyright © 2000, Yokogawa Electric Corporation
COM
N
100-240V AC
When "/24V"
is specified
When "/AL" or "/HBA" is specified
GS 05C01E02-01E
5th Edition Jun. 28, 2013-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising