2011-2013 Fiesta 250-9610 - The Cruise Control Store

2011-2013 Fiesta 250-9610 - The Cruise Control Store
2011- 13 FORD FIESTA / 2010 MAZDA 3
PART NUMBER: 250-9610
ELECTRONIC CRUISE CONTROL KIT
GENERAL APPLICABILITY
RECOMMENDED TOOLS
FORD FIESTA ( AT/MT)
PERSONAL & VEHICLE PROTECTION
SAFETY GLASSES
KIT CONTENTS/SERVICE PARTS
ITEM
1
2
3
4
5
6
7
QTY
1
1
1
1
1
1
1
DESCRIPTION
CRUISE CONTROL MODULE
SWITCH HARNESS
PEDAL INTERFACE HARNESS
HARDWARE KIT
CONTROL SWITCH
DIAGNOSTICS HARNESS
CLUTCH HARNESS
5
3
PART#
250-2813
250-2760
250-2821
250-2767
250-3742
250-2785
250-2759
SPECIAL TOOLS
VOLT-OHM METER
INSTALLATION TOOLS
TRIM REMOVAL TOOL
10-MM WRENCH
DRILL BITS
14MM WRENCH
SOLDERING TOOL
SPECIAL CHEMICALS
PHILLIPS SCREWDRIVER
9.5MM
OR
3/8” (FOR
SWITCH)
2
CONFLICTS
NOTE:
7
LEGEND
4
1
STOP: DAMAGE TO
VEHICLE MAY OCCUR.
DO NOT PROCEED
UNTIL
PROCESS COMPLIANCE HAS BEEN MET.
OPERATOR SAFETY: USE CAUTION TO AVOID RISK
6
HARDWARE BAG CONTENTS
ITEM
1
2
3
QTY
8
DESCRIPTION
WIRE ZIP TIES
OF INJURY.
CRITICAL PROCESS: PROCEED WITH CAUTION TO ENSURE A
QUALITY INSTALLATION. THESE POINTS WILL BE AUDITED ON A
COMPLETED VEHICLE INSTALLATION.
GENERAL PROCESS: THIS
HIGHLIGHTS SPECIFIC PROCESSES TO
ENSURE A QUALITY INSTALLATION. THESE POINTS WILL BE AUDITED DURING
THE ACCESSORY INSTALLATION.
TOOLS & EQUIPMENT: THIS
CALLS OUT THE SPECIFIC TOOLS AND
EQUIPMENT REQUIRED FOR THE PROCESS.
REVISION MARK: THIS
MARK HIGHLIGHTS A CHANGE IN
INSTALLATION WITH RESPECT TO PREVIOUS ISSUE.
WARNING: DO NOT USE HAND-HELD 2-WAY TRANSCEIVERS INSIDE YOUR VEHICLE WHILE
DRIVING.
WHEN TRANSMITTING FROM INSIDE THE CAR, 2-WAY RADIOS THAT OPERATE IN THE 25MHZ700MHZ FREQUENCY RANGE WITH MORE THAN 2.0 WATTS OF POWER CAN PRODUCE ELECTROMAGNETIC INTERFERENCE THAT COULD INTERFERE WITH THE OPERATION OF CRUISE
AND THROTTLE CONTROLS RESULTING IN VEHICLE "LIMP MODE".
USE OF CELLULAR PHONES WILL NOT INTERFERE WITH THESE CONTROLS.
DUE TO SENSITIVE NATURE OF SIGNALS USED FOR THIS PRODUCT, ALL NON-PLUG AND
PLAY CONNECTIONS MUST BE SOLDERED. FAILURE TO COMPLY WITH THIS REQUIREMENT
WILL VOID WARRANTY.
FORM #5268, REV. F, 03-27-13
2011- 13 FORD FIESTA / 2010 MAZDA 3
PART NUMBER: 250-9610
ELECTRONIC CRUISE CONTROL KIT
BEFORE INSTALLATION
To make the installation easier, the complete installation instructions should be read through
before installation is started.
This installation instructions contains information how to install the Electronic Cruise Control
which is not a Do-It-Yourself job.
Modern cars are equipped with electronics, which can be costly damaged by inappropriate treatment.
Rostra Precision Controls can not be held responsible for any error caused by wrong installation
READ BEFORE INSTALLATION-IMPORTANT
ADVISORY NOTES THAT YOU MUST FOLLOW
Always disconnect the negative cable from battery before installation.
Always use the enclosed installation instruction for installing the Electronic Cruise Control.
Check the part number of the cruise module label is the same compared to the part number of
the installation instructions.
Be aware of radio codes that might have to be typed in.
Find a location to install the cruise module and control switch
If any wires are left, then cut off and insulate.
Only use a multimeter to measure voltage.
Always drive the car for a complete test before assembling the car.
All wire leads must be soldered.
2011- 13 FORD FIESTA / 2010 MAZDA 3
PART NUMBER: 250-9610
10mm Wrench
Fig. 1-1
ELECTRONIC CRUISE CONTROL KIT
Negative
Battery
Cable
Battery
*Note: If the OBD2 interface
connector does not fit, or
you do not want to use the
plug cap, cut the Rostra connector off and solder wires:
Red Wire to Pin 6, Black
Wire to Pin 14 of OBD2 connector in the vehicle.
To OBD2
Connector
Connect to the
accelerator pedal
2011- 13 FORD FIESTA / 2010 MAZDA 3
INSTALLATION
ELECTRONIC CRUISE CONTROL KIT
Red
Ignition
Check ignition wire with a volt-meter
to be sure voltage is 0V with key off
and holds at +10V during crank/start
Ford Fiesta
Mazda 3
BEHIND DRIVERS KICK PANEL
BEHIND DRIVERS KICK PANEL
PINK
GREEN/ORANGE
2011- 13 FORD FIESTA / 2010 MAZDA 3
INSTALLATION
ELECTRONIC CRUISE CONTROL KIT
White
Clutch negative
For manual transmission vehicles only.
Connect Clutch Harness to Control
Module. Connect White Wire to ground
triggered (white wire) at Clutch Switch
CLUTCH SWITCH
WHITE
2011- 13 FORD FIESTA / 2010 MAZDA 3
INSTALLATION
ELECTRONIC CRUISE CONTROL KIT
*Order of Placement is not critical
Do not drill hole for
control switch before
testing the cruise system
Use the lever wedges on the Control Switch at
an angle template to drill a 3/8" or 9.5mm hole
2011- 13 FORD FIESTA / 2010 MAZDA 3
PART NUMBER: 250-9610
ELECTRONIC CRUISE CONTROL KIT
A
B
C
Green
4 volts
Ignition
White
4 volts
Ignition
Blue
7 volts
Ignition
0.7 volts
Ignition
PIN
COLOR
13A
RED
14A
BLACK
Gray
7 volts
Ignition
accelerator pedal interface voltages
with the pedal fully depressed
accelerator pedal interface voltages
with the pedal not depressed
1.0 volts
Ignition
DESIRED RESULTS
+12V
WHEN SWITCHED ON AND
+OV
FAULT CONDITION
NO
WHEN
CONNECTION WILL CAUSE LOSS OF PEDAL OR
+10V WHILE CRANKING VEHICLE.
LOWEST RESISTANCE TO GROUND AND CLOSEST
ZERO (0) OHMS AS POSSIBLE. USE A VEHICLE
“LIMP MODE” CONDITION.
A BAD GROUND CONNECTION WILL CAUSE THE
FOLLOWING CONDITIONS: CRUISE WILL NOT
FUNCTION, LOSS OF PEDAL OR “LIMP MODE”
CONDITION.
CRUISE WILL NOT SET IF THIS CONNECTION IS
NOT INSTALLED CORRECTLY.
CRUISE WILL NOT RESUME OR ACCEL IF THIS
CONNECTION IS NOT INSTALLED CORRECTLY.
CRUISE WILL NOT SET IF THIS CONNECTION IS
NOT INSTALLED CORRECTLY.
CRUISE LIGHT WILL NOT COME ON IF THESE
TO
GROUND POINT WHERE OTHER GROUND WIRES ARE
CONNECTED TO.
1B
GREEN
SET/COAST: 12V
2B
YELLOW
RESUME/ACCEL: 12V
3B
BROWN
ON/OFF: 12V
6B
8B
5C
RED AND BLUE
BLACK
WHITE
12V
(0) OHMS RESISTANCE TO GROUND
GROUND ACTIVE WIRE AT SWITCH WHEN CLUTCH
DEPRESSED.
+12V ACTIVE WIRE AT SWITCH WHEN CLUTCH IS
DEPRESSED.
6C
YELLOW
POWER, VOLTAGE DROP, OR INTERMITTENT
SWITCHED OFF. IGNITION MUST BE GREATER THAN
PRESS AND HOLD SET
PRESS AND HOLD RESUME
PRESS ON
CONNECTIONS ARE NOT INSTALLED CORRECTLY.
IS
CRUISE
WILL NOT FUNCTION IF WRONG WIRE IS
CONNECTED
-OR- CRUISE
WILL NOT DISEN-
GAGE WHEN CLUTCH IS DEPRESSED.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising