model sf20110 sand filter pump
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
OWNER’S MANUAL
English
127
IMPORTANT
SAFETY RULES
Read, understand, and follow all
instructions carefully before
installing and using this product.
Sand Filter Pump
Model SF20110
For illustrative purposes only.
Don’t forget to try these other fine Intex products: pools, pool accessories,
inflatable pools and in-home toys, airbeds and boats available at fine
retailers or visit our website.
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance,
Visit www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
127-***-R1-1211
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
TABLE OF CONTENTS
English
Warnings.......................................................................... 3
Parts List & References.................................................. 4-8
Setup Instructions ......................................................... 9-16
Product Specifications................................................... 11
Operating Instructions ................................................... 17-19
Intex Pools Operating Time Table.................................. 20-21
Non-Intex Pools Operating Time Table.......................... 22
Maintenance.................................................................... 23
Long Term Storage.......................................................... 24
Troubleshooting Guide................................................... 25
Common Pool Problems................................................. 26
General Aquatic Safety................................................... 27
Limited Warranty............................................................. 28
Intex Service Center Locations..................................... 29
SAVE THESE INSTRUCTIONS
Page 2
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
SAFETY RULES
English
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
• To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
• Children must stay away from this product and electrical cord(s).
• Assembly and disassembly by adults only.
• Risk of electric shock. Connect only to a grounding type receptacle, this product
is provided with a ground-fault circuit interrupter. If replacement of the plug or cord
is needed, use only identical replacement parts.
• Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
• The unit is provided with a ground-fault circuit interrupter (GFCI). To test the GFCI,
push the test button. The GFCI should interrupt power. Push the reset button, power
should be restored. If the GFCI fails to operate in this manner. The GFCI is
defective. If the GFCI interrupts power to the pump without the test button being
pushed, a ground current is flowing, indicating the possibility of an electric shock.
Do not use this pump. Disconnect the pump and have the problem corrected by a
qualified service representative before using.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
• To reduce the risk of electric shock, replace damaged cord immediately. Use a
qualified electrician to replace the cord.
• To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
• Do not use an appliance leakage current interrupter (ALCI) in place of a GFCI
since the ALCI will not protect people.
• Position this product away from pool, so as to prevent children from climbing on it
and access the pool.
• Do not operate this product when pool is occupied.
• To reduce the risk of entrapment hazard, never enter the pool if suction strainer
component is loose, broken, cracked, damaged or missing. Replace loose, broken,
damaged, cracked or missing suction strainer components immediately.
• Never play or swim near suction fittings. Your body or hair may be trapped causing
permanent injury or drowning.
• To prevent equipment damage and risk of injury, always turn pump off before
changing the filter control valve position.
• Never operate this product above the maximum working pressure stated on the
filter tank.
• Hazardous Pressure. Improper tank valve cover assembly could cause the valve
cover to blow off and cause serious injury, property damage or death.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
CAUTION
This product is for use with storable pools only. Do not use with permanently-installed pools. A
storable pool is constructed so that it is capable of being readily disassembled for storage and
reassembled to its original integrity. A permanently-installed pool is constructed in or on the
ground or in a building such that it cannot be readily disassembled for storage.
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
SAVE THESE INSTRUCTIONS
Page 3
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
PARTS LI ST
English
PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
17
18
19
20
21
15
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
SAVE THESE INSTRUCTIONS
Page 4
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
PARTS LI ST
English
PARTS LIST (continued)
22
23
25
26
28
29
24
27
30
Optional
31
Optional
32
33
35
36
Optional
34
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
SAVE THESE INSTRUCTIONS
Page 5
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
PARTS REFERENCE
English
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
2
12
13
1
11
3
14
5
35
4
15
18
6
16
32
38
37
17
7
11
34
39
9
33
10
20
19
8
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS
Page 6
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
PARTS REFERENCE
English
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
23
24
25
26
27
21
22
23
24
25
26
36
21
22
23
28
29
28
29
30
21
22
23
31
21
22
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
SAVE THESE INSTRUCTIONS
Page 7
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
PARTS REFERENCE
English
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
REF. NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
DESCRIPTION
PRESSURE GAUGE
6-WAY VALVE
DRAIN OUTLET COVER
CLAMP
TANK O-RING
SAND SHIELD
CENTER PIPE HUB
LATERAL
DRAIN VALVE CAP
DRAIN VALVE O-RING
L-SHAPE O-RING
HOSE WITH NUTS
SAND FILTER INTERCONNECTING HOSE
LEAF TRAP NUT
LEAF TRAP O-RING
BASKET
FILTER HOUSING NUT
L-SHAPE O-RING
SEDIMENT RELEASE VALVE
VALVE O-RING
PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED)
HOSE O-RING
STEP WASHER
STRAINER NUT
FLAT STRAINER RUBBER WASHER
THREADED STRAINER CONNECTOR
ADJUSTABLE POOL INLET NOZZLE
ADAPTOR B
STRAINER CONNECTOR
POOL INLET NOZZLE
STRAINER GRID
SCREW
PUMP MOTOR & CONTROL
PRE-FILTER ASSEMBLY
LEAF TRAP COVER
STRAINER GRID
SAND FILTER PUMP MOTOR INLET O-RING
16” SAND FILTER PUMP AND COMBO TANK
16” SAND FILTER PUMP TANK BASE
QTY.
1
1
1
1
1
1
1
10
1
1
4
2
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
2
2
1
1
2
1
1
1
1
2
1
1
SPARE PART
NO.
11224
11496
11131
11380
11379
11382
11495
11384
11456
11385
11228
11009
11535
11479
11232
11260
11261
11412
10460
10264
10747
10262
10745
10256
10255
10744
11074
10722
11070
11071
11072
11381
11322EG
11371
11480
10253
11457
11497
11514
When ordering parts, be sure to quote the model number and part numbers.
SAVE THESE INSTRUCTIONS
Page 8
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
SETUP I NSTRUCTIONS
English
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. If your pool has an inflatable top ring, install the strainer, nozzle
and plunger valve before inflating the pool liner top ring. The part numbers
here onward refer to the parts depicted in the Parts List section of this
manual. To install, do the following:
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (26) (see drawing 1).
Be careful not to lose the step rubber
washer (23). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (24) from the threaded
connector (26). Leave the flat washer (25)
on the connector (26).
3. Install the strainer and plunger valve at the
lower position of pool outlet (marked "+").
From the inside of the pool liner insert the
connector (26) into one of the pre-cut holes
with the washer remaining on the
connector to be placed against the inside
of the liner wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. With the flat side of the
strainer nut (24) facing the outside wall of
the liner in a clockwise motion screw the
strainer nut (24) back onto the threaded
connector (26) (see drawing 2).
5. Finger tighten the strainer nut (24) onto the
threaded connector (26).
6. Grasp the plunger valve assembly. Make
sure the step washer (23) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (26) (see drawing 3).
8. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at
the top and push down turning the handle
in a clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from
flowing out during filling (see
drawings 4.1 & 4.2).
1
2
1
23
INSIDE
LINER WALL
25
24
2
26 36
3
1
2
1
2
SAVE THESE INSTRUCTIONS
4.1
INSIDE
LINER
WALL
4.2
Page 9
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
SETUP I NSTRUCTIONS
English
POOL INLET - NOZZLE & PLUNGER VALVE SETUP
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (26) (see drawing 5).
Be careful not to lose the step rubber
washer (23). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (24) from the threaded
connector (26). Leave the flat washer (25)
on the connector (26).
3. Install the nozzle and plunger valve at the
upper position of pool inlet. From the inside
of the pool liner insert the connector (26)
into one of the pre-cut holes with the
washer remaining on the connector to be
placed against the inside of the liner wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. With the flat side of the
strainer nut (24) facing the outside wall of
the liner in a clockwise motion screw the
strainer nut (24) back onto the threaded
connector (26) (see drawing 6).
5. Finger tighten the adjustable pool inlet
nozzle (27) and the strainer nut (24) onto
the threaded connector (26).
6. Grasp the plunger valve assembly. Make
sure the step washer (23) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (26) (see drawing 7).
8. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at
the top and push down turning the handle
in a clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from
flowing out during filling (see
drawings 8.1 & 8.2).
9. Adjust the direction of nozzle head pointing
away from the pool outlet for a better
circulation result (see drawing 9).
10. The pool liner is now ready to fill with
water. Consult the above-ground-pool
owner’s manual for filling instructions.
5
2
1
INSIDE
LINER WALL
24
25
26
6
27
7
1
2
8.1
1
INSIDE
LINER
WALL
2
8.2
9
WATER
FLOW
POOL
SAVE THESE INSTRUCTIONS
Page 10
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
PR O DU C T S P EC S & SE TU P IN S TR U CT IO N S
English
PRODUCT SPECIFICATIONS
The sand filter removes suspended particles but does not sanitize your pool.
Pool chemistry is a specialized area and you should consult your local pool
service specialist for details.
Power:
Amperage:
Maximum working pressure:
Effective filtering area:
Maximum Flow Rate:
Recommended filtering media:
(Not included)
110-120 Volt AC
6.0 A
3.5 bar (50 psi)
0.13 m2 (1.44 ft2)
10030 liters/hour (2650 gallons/hour)
No. 20 silica sand or glass sand. Particle size
range 0.45 to 0.85 mm (0.018 to 0.033 inches).
Uniformity Coefficient less than 1.75.
Recommended filtering media quantity: No. 20 silica sand 45 Kg (100 Lbs) or glass
sand 32 Kg (70 Lbs).
Limited Warranty:
see “Limited Warranty”
NOTE: NOT SUITABLE FOR USE WITH KCP-LOW -SALT AUTOMATIC SALTWATER
SYSTEM (MODEL 6110/6220)
SETUP INSTRUCTIONS
TOOLS REQUIRED: One (1) Phillips screwdriver
Pump location and mounting:
• The system must be installed on a solid level and vibration-free base.
• Provide a location protected from the weather, moisture, flooding and
freezing temperature.
• Provide adequate access, space and lighting for routine maintenance.
• Pump motor requires free circulation of air for cooling. Do not install
the pump in a damp or non-ventilated location.
A team of 2 or more people is recommended for setting up this product.
Motor pre-filtering assembly setup:
1.
2.
3.
14
Remove the sand filter and its accessories
from the packaging carefully and inspect for
any visible damage. If parts are damaged
contact your local service center listed at
the back of this owner’s manual.
In a counter-clockwise motion unscrew the
leaf trap cover (14) from the pre-filter
housing. Take out the basket (16) and filter
housing nut (17) (see drawing 10).
Connect the pre-filter housing to the motor
water inlet. Note: Align the connector in the
pre-filter housing with the water inlet on the
motor (see drawing 11).
SAVE THESE INSTRUCTIONS
10
35
16
17
11
Page 11
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
SETUP I NSTRUCTIONS
English
SETUP INSTRUCTIONS (continued)
4. In a clockwise motion screw filter housing nut (17) onto the motor water inlet
(See drawings 12.1 & 12.2).
12.2
12.1
17
17
5. Replace the basket (16) and leaf trap cover (14) back to the pre-filter housing
(See drawings 13.1 & 13.2).
13.1
14
35
13.2
16
Sand tank installation:
1.
2.
3.
Place the tank support base on the selected location.
Place the tank on the tank support base (See drawing 14.1).
Connect the motor pre-filtering assembly unit to the tank support base (See
drawing 14.2). NOTE: Ensure the pre-filter housing water inlet hose connection
is facing towards the pool.
IMPORTANT: Some countries, especially in the European community,
require the product to be secured to the ground or to a base in a
permanent upright position. Check your local authorities to determine if
there is a regulation in your area regarding above-the-ground swimming
pool filter-pumps. If yes, then the product can be mounted to a platform
using the two holes located in the base. See drawing 14.3.
The product can be mounted on a cement base or onto a wooden
platform to prevent accidental falling over.
• The mounting holes are 6.4 mm in diameter and spaced (177.4 mm)
apart.
• Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.
14.1
14.2
14.3
6.98in
(177.4mm)
SAVE THESE INSTRUCTIONS
Page 12
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
SETUP I NSTRUCTIONS
English
SETUP INSTRUCTIONS (continued)
Sand loading:
IMPORTANT: Use No. 20 silica sand or glass sand with particle size range
0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less
than 1.75.
NOTE: Before loading the tank with sand, ensure the center pipe hub
assembly is securely in place at the bottom of the tank, and vertically
centered inside the tank.
1.
2.
Place the sand shield (6) over the top of the center pipe. Pour the sand into the
tank at a slow rate. (see drawing 15).
Fill the tank approximately half way, remove the sand shield (6) from the top.
(see drawing 16).
15
16
6
6
3.
4.
Evenly distribute the sand inside the tank, then fill the tank with some water to
provide a cushioning effect when the remaining sand is poured in. This
prevents the center pipe hub (7) from excessive shock (see drawing 17).
Place the sand shield (6) back and continue to pour the sand into the tank.
Sand shall be filled between the “MAX” and “MIN” marked gauge on the center
pipe. Evenly spread and level out the sand by hand (see drawings 17 & 18).
7
18
17
7
MAX
MAX
MIN
MIN
MAX
MIN
5.
6.
Remove the sand shield (6).
Wash away all sand around the top edge of the tank.
SAVE THESE INSTRUCTIONS
Page 13
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
SETUP I NSTRUCTIONS
English
SETUP INSTRUCTIONS (continued)
WARNING
Improper tank valve and clamp assembly could cause the valve and clamp to blow
off and cause serious injury, property damage or death.
6-way valve installation:
1.
Lower the 6-way valve over the tank slowly, and ensure the bypass pipe protruding
underneath the 6-way valve fits securely into the center pipe hub (7) top opening (see
drawing 19).
IMPORTANT: There are three hose connection ports on the 6-way valve,
ensure the outlet connection (from filter to the pool) on the valve is facing
towards the pool, and the inlet connection (from motor to valve) is aligned
with the motor outlet (see drawing 20).
19
20
WATER
INLET
WATER
OUTLET
7
2.
3.
Place an L-shape o-ring (11) on the 6-way valve inlet connection and on the
pump motor outlet. In a clockwise motion connect the sand filter
interconnecting hose (13) between the pump motor outlet and the 6-way valve
inlet connection (see drawing 21).
Remove the clamp bolt, and install the clamp around the tank and 6-way valve
flanges, then replace the clamp bolt and use a phillips screwdriver (not
included) to tighten it (see drawings 22).
21
13
SAVE THESE INSTRUCTIONS
22
4
Page 14
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
SETUP I NSTRUCTIONS
English
SAND FILTER PUMP HOSE CONNECTION SETUP
WARNING
• Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.
The 6-way valve has three hose connection ports.
1. Connect one hose (12) end to the pre-filter inlet and the other end of the hose
to the lower plunger valve with the strainer. Ensure the hose nuts are securely
tightened.
2. Connect the second hose (12) between the 6-way valve water outlet and the
upper plunger valve with the inlet-nozzle. Ensure the hose nuts are securely
tighten.
3. The third hose connection port (drain/waste outlet) on the 6-way valve shall be
directed to a proper draining receptacle using a hose or pipe (not provided).
Remove the drain cap before attaching the drain/waste hose or pipe.
4. The sand filter pump is now ready to filter the pool.
6-WAY VALVE
PLUNGER
VALVE
WATER
OUTLET
WATER
INLET
WATER LEVEL
L-SHAPE
O-RING
ADJUSTABLE
POOL INLET
NOZZLE
WATER INLET
STRAINER
GRID
TO
DRAIN
L-SHAPE
O-RING
OUTSIDE
LINER WALL
POWER
CORD MOTOR
MOTOR
WATER
OUTLET
PREFILTER
(ILLUSTRATION NOT TO SCALE)
SAVE THESE INSTRUCTIONS
Page 15
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
SETUP I NSTRUCTIONS
English
SAND FILTER PUMP HOSE CONNECTION SETUP (continued)
For NON-INTEX pool:
Connect the hose (12) to the pool inlet/outlet connection with a large hose clamp.
Tighten securely. Remove the drain cap (3) before attaching the drain/waste
hose or pipe.
LARGE HOSE
CLAMP
12
POOL
3
For INTEX pool size 16' and below:
1. In a counter-clockwise motion unscrew plunger valve union from the threaded
strainer connector (26). Be careful not to lose the step rubber washer (23).
2. Grasp the plunger valve assembly. Make sure the step washer (23) is in place.
Connect adaptor B (28) to plunger valve union.
3. Remove wall plug and then insert the strainer (29 & 31) into the lower position
of protruding hose connection, and the nozzle (29 & 30) into the upper position
of protruding hose connection. Adaptor B (28) fits over the strainer
connection (29) inserted into the connection. Tighten securely.
4. Remove the drain cap (3) before attaching the drain/waste hose or pipe.
29 & 30
3
POOL
29 & 31
SAVE THESE INSTRUCTIONS
Page 16
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
OPERATI NG I NSTRUCTIONS
English
OPERATING INSTRUCTIONS
WARNING
• Risk of electric shock. Connect this product only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI) or
residual current device (RCD). Contact a qualified electrician if you cannot
verify that the receptacle is protected by a GFCI/RCD. Use a qualified
electrician to install the GFCI/RCD, which has a maximum rate of 30mA.
Do not use a portable residual current device (PRCD).
• To reduce the risk of electric shock, do not use extension cords, timers,
plug adaptors or converter plugs to connect unit to electric supply;
provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water
or when your hands are wet.
• Never operate this product above the maximum working pressure stated
on the filter tank.
• Always switch off pump before changing the 6-way valve position.
• Operating this product without water flowing through the system can
cause a build up of hazardous pressure which can result in an explosive
situation, serious injury, property damage or death.
• Never test this pump with compressed air. Never operate the system with
water temperature above 35° C (95° F).
6-way valve positions and function:
Valve Position
Function
Normal filtration and regular
FILTER
(see drawing 23) vacuuming of pool
BACKWASH Reverses water flow to clean
(see drawing 24) filter media
For initial startup cleaning of the sand, and
RINSE
(see drawing 25) leveling the sand bed after backwashing
For vacuuming directly to waste,
WASTE
(see drawing 26) lowering pool level or to drain the pool
Water Flow Direction
From pump through filter media
to pool
From pump through filter media
to valve waste/drain outlet
From pump through filter media
to valve waste/drain outlet
From pump to valve waste/drain
outlet bypassing the filter media
RECIRCULATE For circulating water back to pool
From pump through valve to
pool bypassing the filter media
(see drawing 27) without going through the filter media
Shuts off all flow to filter and pool
CLOSED
(see drawing 28) “Do not use this setting with pump running”
23
24
25
SE
RIN
SE
RIN
WASTE
WASTE
BA
CK
WA
SH
WASTE
Page 17
FIL
TE
R
FIL
TE
R
WASTE
FIL
TE
R
FIL
TE
R
SE
RIN
SE
RIN
ER
SE
RIN
SE
RIN
WASTE
RECIRCULATE
RECIRCULATE
RECIRC
RECIRCUL
FIL
TE
R
SE
FIL
TE
R
RE
SE
RIN
RE
BA
CK
WA
FIL
TE
R
SE
RIN
FIL
TE
R
BA
CK
WA
SH
SAVE THESE INSTRUCTIONS
STE
WASTE
WASTE
SE
RIN
WASTE
WASTE
FIL
TE
R
WASTE
SE
RIN
SE
RIN
E
OS
CL
FIL
TE
R
SE
RIN
BA
CK
WA
SH
E
OS
CL
FIL
TE
R
FIL
TE
R
SE
RIN
E
OS
CL
RECIRCULATE
B
BA
CK
WA
SH
RECIRCULATE
BA
CK
WA
SH
RECIRCULATE
RECIRCULATE
E
OS
CL
E
OS
CL
RECIRCULATE
RECIRCULATE
RECIRCULATE
RECIRCULATE
BA
CK
WA
SH
B
WASTE
WASTE
WASTE
WASTE
BA
CK
WA
SH
BA
CK
WA
SH
BA
CK
WA
SH
English
127
OPERATING INSTRUCTIONS (continued)
26
27
28
FIL
TE
R
SE
RIN
WASTE
FIL
TE
R
SE
RIN
SE
RIN
SE
RIN
FIL
TE
R
FIL
TE
R
BA
CK
WA
SH
BA
CK
WA
SH
E
OS
CL
E
OS
CL
SE
RIN
Initial startup and operation:
Before operating, be sure that:
• All the hoses have been connected and tightened securely, and correct amount
of filter sand have been loaded.
• The entire system is connected to a grounding type receptacle protected by a
ground-fault circuit interrupter (GFCI) or residual current device (RCD).
CAUTION
The filter control valve has a closed position. The pump should never be
on when the valve is in the closed position. If the pump is operated with
the valve closed, explosive situation could exist.
1. Grasp plunger valve handle. Turn the handle counter-clockwise, pull up until it
stops, and then turn it clockwise until the metal protruding notch anchor is in
the "0/1" position. Repeat for the second plunger valve. This opens the valves to
allow water to flow into the sand filter pump
2. Ensure the drain/waste outlet on the 6-way valve is not covered and directed to
a proper draining receptacle.
3. Ensure the pump is off, depress the 6-way
valve and turn it to the “BACKWASH” position
(see drawings 24 & 29).
IMPORTANT: To prevent damage to the
6-way valve, always depress the valve
handle before turning. Always switch off
pump before changing the 6-way valve
position.
4. Switch on the pump (see drawing 30). Water
is circulating backward through the sand
media and to waste/drain outlet. Backwash
until a clear flow of water is observed in the
waste/drain outlet or through the drain sediment
window.
NOTE: The initial backwash of the filter is
recommended to remove any impurities or fine
sand particles in the sand media.
SAVE THESE INSTRUCTIONS
29
1
2
30
TIMER
WASTE
FIL
TE
R
FIL
TE
R
WASTE
FIL
TE
R
BA
CK
WA
SH
OFF
ON
Page 18
E
OS
CL
RECIRCULATE
E
OS
CL
RECIRCULATE
E
OS
CL
RECIRCULATE
BA
CK
WA
SH
E
OS
CL
BA
CK
WA
SH
RECIRCULATE
RECIRCULATE
RECIRCULATE
RE
WASTE
RE
BA
CK
WA
SH
OPERATI NG I NSTRUCTIONS
E
OS
CL
WASTE
SE
RIN
FIL
TE
R
WASTE
SE
RIN
SE
RIN
FIL
TE
R
WASTE
E
FIL
BA
CK
WA
SH
E
OS
CL
E
OS
CL
SE
RIN
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
B
BA
CK
WA
SH
FIL
TE
R
E
OS
CL
RECIRCULATE
BA
CK
WA
SH
RECIRCULATE
E
OS
CL
RECIRCULATE
BA
CK
WA
SH
RECIRCULATE
RECIRCULATE
E
OS
CL
CULATE
RECIRCULATE
RECIRCULATE
B
BA
CK
WA
SH
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
OPERATI NG I NSTRUCTIONS
English
OPERATING INSTRUCTIONS (continued)
5. Switch off the pump, change the 6-way valve to “RINSE” position (see
drawing 25).
6. Switch on the pump and run the pump for about one minute to level out the
sand bed after backwashing the sand media.
7. Switch off the pump, change the 6-way valve to “FILTER” position (see
drawing 23).
8. Switch on the pump. The system is now operating in the normal filtering mode.
Run the pump until the desired pool water clearance is obtained and no more
than 12 hours per day.
9. Record the initial pressure gauge reading when the filter media is clean.
NOTE: During initial setup of the system, it may be necessary to backwash
frequently due to unusual heavy dirt present in the water and sand. After that,
as the filter removes dirt and impurities from the pool water, the accumulated
dirt in the sand media will cause the pressure to rise and the flow to diminish. If
there is no vacuuming device attached to the system and the pressure gauge
reading is in the yellow zone it is time to backwash the sand media, see
“BACKWASH” under “initial startup and operation” section.
Vacuuming device (i.e. Intex auto pool cleaner) attached to the system may also
cause the flow to diminish and the pressure to rise. Remove any vacuuming
device from the system and check if the pressure gauge reading has dropped
from the yellow zone to the green zone.
Operating the system under “TIMER” mode or manually:
To operate the sand filter pump in “FILTER” mode under “TIMER” control:
A. Set the timer dial to the desired operating hours. See operation time table
(see drawing 31).
B. Turn on the pump by pressing the switch to “ ” position, the sand filter
pump is now filtering the water and will stop after the operating hours are
completed. The built-in timer will now operate for the number of hours
selected at the same time each day.
C. Operating hours can be re-adjusted if necessary. Follow step A – B.
To operate the sand filter pump manually (without the “TIMER” mode):
A. Turn on the pump by pressing the switch to “-” position, the sand filter
pump is now filtering the water.
B. To turn off the pump, press the switch to “O” position.
31
TIMER DIAL
(HOURS)
TIMER
OFF
ON
SAVE THESE INSTRUCTIONS
Page 19
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
English
127
INTEX POOLS OPERATING TIME TABLE (WITHOUT INTEX SALTWATER SYSTEM)
This table shows the required operating time for average use of the sand filter pump with above
ground pools.
Pool Size
Sand filter
Water Capacity (Calculated at
pump operating
90% for Frame Pool and 80% for
time (For one
Easy Set & Oval Pool)
cycle)
(Gals)
(Liters)
(Hours)
18' x 42" (549cm x 107cm)
4786
18115
2
18' x 48" (549cm x 122cm)
5455
20647
2
18' x 52" (549cm x 132cm)
5894
22309
4
18' x 48" (549cm x 122cm)
6423
24311
4
18' x 52" (549cm x 132cm)
6981
26423
4
24' x 48" (732cm x 122cm)
11483
43462
6
24' x 52" (732cm x 132cm)
12481
47421
6
18' x 52" (549cm x 132cm)
6981
26423
4
15'8" x 49" (478cm x 124cm)
4440
16805
2
18'8" x 53" (569cm x 135cm)
6981
26423
4
20' x 12' x 48" (610cm x 366cm x 122cm)
4393
16628
2
24' x 12' x 48" (732cm x 366cm x 122cm)
5407
20465
2
28' x 12' x 48" (853cm x 366cm x 122cm)
6420
24300
4
18' x 9' x 52" (549cm x 274cm x 132cm)
4545
17203
2
24' x 12' x 48" (732cm x 366cm x 122cm)
7757
29359
4
24' x 12' x 52" (732cm x 366cm x 132cm)
8403
31805
4
32' x 16' x 52" (975cm x 488cm x 132cm)
14364
54368
8
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
ROUND
METAL
FRAME POOL
ULTRA FRAME
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
SAVE THESE INSTRUCTIONS
Page 20
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
English
127
INTEX POOLS OPERATING TIME TABLE (WITH INTEX SALTWATER SYSTEM)
If the system is attached to an “Intex Saltwater System” unit, the filter pump running time
should be longer than the required operating time of the Intex Saltwater System unit.
Pool Size
Saltwater System
Water Capacity (Calculated at
Sand Filter
operating Time (with
90% for Frame Pool and 80%
Pump
cyanuric acid 30-50ppm) (hours) Operating
for Easy Set & Oval Pool)
Time
10 - 19°C 20 - 28°C 29 - 36°C
(Gals)
(Liters)
(50 - 66°F) (68 - 82°F) (84 - 97°F) (hours)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME
POOL
18' x 42" (549cm x 107cm)
4786
18115
2
2
2
4
18' x 48" (549cm x 122cm)
5455
20647
2
2
3
4
18' x 52" (549cm x 132cm)
5894
22309
2
2
3
4
18' x 48" (549cm x 122cm)
6423
24311
2
2
3
4
18' x 52" (549cm x 132cm)
6981
26423
2
2
3
4
20' x 52" (610cm x 132cm)
8638
32695
3
3
4
6
24' x 48" (732cm x 122cm)
11483
43462
4
4
5
6
24' x 52" (732cm x 132cm)
12481
47241
5
5
6
8
18' x 52" (549cm x 132cm)
6981
26423
2
2
3
4
SEQUOIA SPIRIT®
POOL SET
15'8" x 49" (478cm x 124cm)
4440
16805
2
2
2
2
18'8" x 53" (569cm x 135cm)
6981
26423
2
2
3
4
20' x 12' x 48" (610cm x 366cm x 122cm)
4393
OVAL FRAME
POOL
16628
2
2
2
4
24' x 12' x 48" (732cm x 366cm x 122cm)
5407
20465
2
2
3
4
28' x 12' x 48" (853cm x 366cm x 122cm)
6420
24300
2
2
3
4
18' x 9' x 52" (549cm x 274cm x 132cm)
4545
17203
2
2
2
4
24' x 12' x 52" (732cm x 366cm x 132cm)
8403
31805
3
3
4
6
32' x 16' x 52" (975cm x 488cm x 132cm)
14364
54368
6
6
7
8
RECT. ULTRA
FRAME POOL
NOTE: The “12” hours timer setting position has an additional 20 minutes over the actual
setting.
SAVE THESE INSTRUCTIONS
Page 21
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
English
127
NON-INTEX POOLS OPERATING TIME TABLE
This table shows the required operating time for average use of the sand filter pump with above
ground pools.
Sand filter pump operating
time (For one cycle)
Water Capacity
(Gals)
(Liters)
(Hours)
4000
15140
2
4440
16805
2
5000
18925
2
6000
22710
4
7000
26495
4
8000
30280
4
9000
34065
4
10000
37850
6
11000
41635
6
12000
45420
6
13000
49205
6
14000
52990
6
15000
56775
8
16000
60560
8
17000
64345
8
18000
68130
8
19000
71915
12
20000
75700
12
21000
79485
12
22000
83270
12
23000
87055
12
24000
90840
12
25000
94625
12
26000
98410
12
SAVE THESE INSTRUCTIONS
Page 22
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
MAI NTENANCE
English
MOTOR PRE-FILTER CLEANING AND MAINTENANCE
1. Make sure the filter pump is switched off, then disconnect the power cord from
the electrical outlet.
2. Grasp a plunger valve handle. Turn the handle counter-clockwise, push down
until it stops and then turn it clockwise until the plastic protruding notch anchors
in the "0/1" position. Repeat for the second plunger valve. This prevents the
water from flowing out of the pool.
32
3. Release the pressure first by opening the
sediment release valve (19) located
on the lower side of the pre-filter housing
(see drawing 32).
1
2
19
4. In a counter-clockwise motion unscrew the
leaf trap cover (14), then remove the
basket (16) and leaf trap o-ring (15) from the
pre-filter housing (see drawing 33).
14 33
35
15
16
5. Empty and flush the basket using a garden hose, may use a plastic brush to
remove deposits from the basket. Do not use metal brush.
6. Clean and rinse the inside of the pre-filter housing and the leaf trap O-ring with
a garden hose.
7. Reinstall the leaf trap O-ring, basket and leaf trap cover to the pre-filter housing.
8. Close the sediment release valve (19) back.
SAVE THESE INSTRUCTIONS
Page 23
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
MAI NTENANCE
English
POOL CARE & CHEMICALS
•
•
•
•
•
•
•
All pools require care to keep the water clear and hygienically clean. With proper
chemical control, your filter will help attain this objective. Consult your pool supply dealer
for instructions regarding the proper use of chlorine, algaecide and other chemical
agents required for sparkling clear water.
Keep pool chemicals away from children.
Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations could
occur.
Daily pH checking and chemical treatment of the water is very important and cannot be
overemphasized. Chlorine, algaecide and maintenance of proper pH levels are required
when filling the pool as well as during the season. Consult your local swimming pool
supply store for instructions.
The season's first filling of the pool may have brackish water requiring extra water
additives and extra filtering time. Do not allow swimming in pool until the pH level is
balanced. Consult your local swimming pool supply store for instructions.
Chlorinated water may damage lawns, gardens or shrubbery as children play in the pool
and splash water outside the pool. Lawn areas underneath the pool liner will be
destroyed. Note that some types of grass may grow through the liner.
Filter run time depends on pool size, weather and usage level. Experiment with various
run times so as to produce clean clear water.
CAUTION
Concentrated chlorine solutions may damage the pool liner. Always follow the
chemical manufacturer’s directions, and the health and hazard warnings.
LONG TERM STORAGE & WINTERIZATION
CAUTION
Allowing the water to freeze will damage the sand filter and void the warranty.
If anti-freeze solution is needed, use only propylene glycol. Propylene glycol is
non-toxic and will not damage plastic system components; other anti-freezes
are highly toxic and may damage plastic components in the system.
1.
Before emptying your pool for long term storage, or relocation, be sure the water is
directed towards an acceptable drain water receptacle away from the house. Check local
regulations for specific directions regarding disposal of swimming pool water.
2. Switch off the unit, and disconnect power cord from electrical outlet.
3. When the pool is empty, disconnect all hoses from pump and plunger valves and
remove the strainers/plunger valves from the pool wall.
4. In a counter clockwise motion unscrew the drain valve cap (9) from the drain valve to
thoroughly drain the tank. The drain valve is located at the bottom of the filter tank.
5. Disassemble the pump motor from the tank base.
6. Leave sand filter pump pieces and hoses outside to thoroughly air dry.
7. Coat the following o-rings and washers with petroleum jelly for long term storage:
• L-shape o-ring (11).
• o-ring A (18).
• Pump hose O-rings (22).
• Strainer valve assembly step washers (23).
• Flat strainer rubber washers (25).
8. Depress the 6-way valve handle and rotate so as to set the pointer on the valve top
“N” position. This allows the water to drain from the valve. Leave the 6-way valve in this
inactive position.
9. It is best to place all dry pieces and pump motor in the original packaging for storage. To
avoid condensation or corrosion problem, do not cover or wrap pump motor with plastic bags.
10. Store the pump motor and accessories in a dry place. The storage's temperature
should be controlled, between 0 degrees Celsius (32 degrees Fahrenheit) and 40
degrees Celsius (104 degrees Fahrenheit).
SAVE THESE INSTRUCTIONS
Page 24
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
TROUBLESHOOTING GUIDE
TROUBLE
CAUSE
SOLUTION
FILTER MOTOR
FAILS TO START
• Line cord must be plugged into a 3
• The motor is not plugged in.
wire outlet that is protected by a Class
• The fuse box needs checking.
A Ground Fault Circuit Interrupter, or
• The GFCI/RCD circuit breaker
RCD.
is tripped.
• Reset circuit breaker. If circuit breaker
• Motor too hot and overload
trips repeatedly, your electrical system
protection is shut off.
may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
• Let the motor cool down and restart again.
FILTER DOESN’T
CLEAN POOL
• Improper chlorine or pH
levels.
• No filtering media in tank.
• Wrong 6-way valve setting
position.
• Excessively dirty pool.
• The strainer screen is
restricting the water flow.
• Adjust the chlorine and pH level. Consult
your local swimming pool supply stores.
• Load with filter sand, see “sand loading
instructions”.
• Set valve to “ FILTER” position.
• Operate the filter for longer periods.
• Clean the strainer screen at the inlet.
FILTER DOESN’T
PUMP WATER OR
FLOW IS VERY
SLOW
•
•
•
•
•
Clogged inlet or discharge.
An air leak on the intake line.
Excessively dirty pool.
Sand media clogged with dirt.
Nozzle and strainer
connections are reversed.
• Crusting or caking on the
filtering sand surface.
• Pool vacuuming device
attached to the system.
• Clear any obstructions in the intake
hose by discharging it inside pool wall.
• Tighten hose nuts, check hoses for
damage, check pool water level.
• Clean the pre-filtering basket more often.
• Backwash filter.
• Install the nozzle at the upper position
of the pool inlet, and the strainer at the
lower position of the pool outlet.
• Remove about 1” of sand if necessary.
• Remove any pool vacuuming device
attached to the system line.
PUMP DOESN’T
WORK
•
•
•
•
Low water level.
Strainer screen clogged up.
An air leak on the intake hose.
Faulty motor or the impeller
is jammed.
• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose nuts, check hose for
damage.
• Contact Intex service center.
6-WAY
VALVE/COVER
LEAKING
•
•
•
•
Sand tank o-ring missing.
Sand tank o-ring dirty.
Flange clamp not tight.
6-way valve damage.
• Remove 6-way valve cover and ensure the
o-ring is in place.
• Clean sand tank o-ring with garden hose water.
• Tighten the clamp with wrench supplied.
• Contact Intex service center.
HOSE LEAKING
• Hose nut not securely tight.
• Hose connection fitting
o-ring/L-shape o-ring missing.
• Tighten/reinstall hose nut.
• Ensure o-ring/L-shape o-ring is in place
and not damaged.
TIMER IS
INACCURATE OR
TIMER CAN'T BE
SET
• Possible inner timer
defective.
• Turn off the pump and restart 5 minutes
later.
• Re-set the timer.
• Contact Intex service center.
PRESSURE GAUGE
DOESN’T WORK
• Clogged inlet of the pressure
gauge.
• Pressure gauge damage.
• Clear any obstructions in the intake by
unscrewing it from the 6-way valve.
• Contact Intex service center.
SAND IS FLOWING
BACK INTO THE
POOL
• Sand is too small.
• Sand bed is calcified.
• Use only No. 20 silica sand with particle
size range 0.45 to 0.85 mm (0.018
to 0.033 inches) and a Uniformity
Coefficient less than 1.75.
• Change sand.
SAVE THESE INSTRUCTIONS
Page 25
TROUBLESHOOTING GUIDE
English
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
COMMON POOL PROBLEMS
PROBLEM
DESCRIPTION
CAUSE
SOLUTION
ALGAE
• Greenish water.
• Green or black
spots on pool liner.
• Pool liner is
slippery and/or has
a bad odor.
• Chlorine and pH levels
need adjustment.
• Super chlorinate with shock
treatment. Correct pH to your
pool store's recommended
level.
• Vacuum pool bottom.
• Maintain proper chlorine
level.
COLORED
WATER
• Water turns blue,
brown, or black
when first treated
with chlorine.
• Copper, iron or
maganese in water
being oxidized by the
added chlorine.
This is Common.
• Adjust pH level to the
recommended level.
• Run filter until water is clear.
FLOATING
MATTER IN
WATER
• Water is cloudy or
milky.
• "Hard water" caused
by a too high pH level.
• Chlorine content is low.
• Foreign matter in
water.
• Correct the pH level. Check
with your pool dealer for
advice.
• Adjust the chlorine level.
CHRONIC
LOW WATER
LEVEL
• Level is lower than
on previous day.
• Rip or hole in pool
liner or hoses.
• The drain valves are
loose.
• Repair with a patch kit.
• Finger tighten all caps.
SEDIMENT
ON POOL
BOTTOM
• Dirt or sand on
pool floor.
• Heavy use, getting in
and out of pool.
• Use Intex pool vacuum to
clean bottom of pool.
SURFACE
DEBRIS
• Leaves, insects
etc.
• Pool too close to
trees.
• Use Intex pool skimmer.
IMPORTANT
If you continue to experience difficulty, please contact our Consumer
Service Department for assistance. See back cover for contact information.
SAVE THESE INSTRUCTIONS
Page 26
COM MON PROBLEMS
English
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
127
SAFETY GUIDELINES
English
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all risks and dangers.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
• Demand constant supervision. A competent adult should be appointed as
a “lifeguard” or water watcher, especially when children are in and around
the pool.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is supervising pool users about potential pool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
• Instruct all pool users, including children what to do in case of an
emergency.
• Always use common sense and good judgement when enjoying any
water activity.
• Supervise, supervise, supervise.
For additional information on safety, please visit
• The Association of Pool and Spa Professionals: The Sensible Way to
Enjoy Your Aboveground/Onground Swimming Pool www.nspi.org
• American Academy of Pediatrics: Pool Safety for Children www.aap.org
• Red Cross www.redcross.org
• Safe Kids www.safekids.org
• Home Safety Council: Safety Guide www.homesafetycouncil.org
• Toy Industry Association: Toy Safety www.toy-tia.org
SAVE THESE INSTRUCTIONS
Page 27
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
English
127
LIMITED WARRANTY
Your Sand Filter Pump has been manufactured using the highest quality materials and
workmanship. All Intex products have been inspected and found free of defects prior to
leaving the factory. This Limited Warranty applies only to the Sand Filter Pump and
accessories listed below.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this manual, as proof of purchase
will be required and must accompany warranty claims or the Limited Warranty is invalid.
Sand Filter Pump Warranty – 2 Years
Hoses, Plunger Valves & Fittings Warranty – 180 days
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in this manual. The Service Center will determine the
validity of the claim. If the Service Center directs you to return the product, please carefully
package the product and send with shipping and insurance prepaid to the Service Center.
Upon receipt of the returned product, the Intex Service Center will inspect the item and
determine the validity of the claim. If the provisions of this warranty cover the item, the item
will be repaired or replaced at no charge.
Any and all disputes regarding the provisions of this Limited Warranty shall be brought before
an informal dispute settlement board and unless and until the provisions of these paragraphs
are carried forth, no civil action may be instituted. The methods and procedures of this
settlement board shall be subject to the rules and regulations set forth by the Federal Trade
Commission (F.T.C.). IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS
WARRANTY AND IN NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR
EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR
CONSEQUENTIAL DAMAGES OR LIABILITIES. Some states, or jurisdictions do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This Limited Warranty does not apply if the products are subject to negligence, abnormal use
or operation, accident, improper operation, improper voltage or current contrary to operating
instructions, or to damage by circumstances beyond Intex’s control, including but not limited
to, ordinary wear and tear and damage caused by exposure to fire, flood, freezing, rain, or
other external environmental forces. This Limited Warranty applies only to those parts and
components sold by Intex. The Limited Warranty does not cover unauthorized alterations,
repairs or disassembly by anyone other than Intex Service Center personnel.
DO NOT GO BACK TO THE PLACE OF PURCHASE FOR RETURN OR
REPLACEMENT. IF YOU ARE MISSING PARTS OR NEED
ASSISTANCE, PLEASE CALL US TOLL-FREE (FOR U.S. AND
CANADIAN RESIDENTS): 1-800-234-6839 OR VISIT OUR WEBSITE:
WWW.INTEXSTORE.COM.
Proof of Purchase must accompany all returns or the warranty claim will be invalid.
SAVE THESE INSTRUCTIONS
Page 28
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
English
COUNTRIES/REGIONS
SERVICE CENTER LOCATIONS
• UNITED STATES
• CANADA
INTEX RECREATION CORP.
1665 Hughes Way
Long Beach, CA 90801
Tel: 1-800-234-6839
Fax: 310-549-2900
Website: www.intexcorp.com (U.S./Canada only)
Consumer Service Hours: 8:30 am to 5:00 pm
Pacific Time, Mon. thru FRI. only.
• MEXICO
KAY INTERNACIONAL, S.A. DE C.V.
SAN JERONIMO # 550- INT.501 Y 502. COL.
JARDINES DEL PEDREGAL. C.P. 01900
MÉXICO D.F.
Tel: 01-800-347-4020 (Collect Call)
Tel: 55-9172-8035
Fax: 55-9172-8047
E-mail: servicenter@kayinternacional.com
Website: www.intexmexico.com.mx
•
•
•
•
•
•
SUPRO MUNDIAL S.A./
PRODUCTOS SUPERIORES S.A.
Boulevard Andrews, Albrook,
Panama, Rep. of Panama
Tel: 507-300-3800
Fax: 507-300-3813
E-mail: suproadmin@supropanama.com
PANAMA
PARAGUAY
ECUADOR
HONDURAS
EL SALVADOR
NICARAGUA
• COSTA RICA
• DOMINICAN REPUBLIC
• GUATEMALA
• COLOMBIA
• VENEZUELA
CENTURY USA, LLC
4731 W. Atlantic Ave., Suite B-3
Delray Beach, FL 33445, USA
Tel: 561-495-0648
Fax: 561-495-4782
E-mail: sales@centuryusa.com
• MIDDLE EAST REGION
REGION
FIRST GROUP INTERNATIONAL
AL MOOSA GROUP BUILDING, 1ST FLOOR,
OFFICE 102 & 103, UMM HURAIR ROAD,
KARAMA, DUBAI, UAE
TEL: 00971-4-800INTEX(46839) / +971-4-3373322
FAX: 00971-4-3375115
E-mail: intex@firstgroupinternational.com.
Website: www.firstgroupinternational.com
• ASIA
INTEX DEVELOPMENT CO. LTD.
9th Floor,
Dah Sing Financial Centre
108 Gloucester Road,
Wanchai, Hong Kong
Tel: 852-28270000
Fax: 852-23118200
E-mail: xmservicesupport@intexcorp.com.cn
Website: www.intexdevelopment.com
127
For answers to most frequently asked questions, please visit www.intexcorp.com.
Non U.S. Residents, please visit www.intexdevelopment.com.
SAVE THESE INSTRUCTIONS
Page 29
(127) MODEL SF20110 SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2011
INTEX
®
English
For Residents of the U.S. & Canada:
INTEX RECREATION CORP.
Attn: Consumer Service
1665 Hughes Way
Long Beach, CA 90801
Phone: 1-800-234-6839
Fax: (310) 549-2900
Consumer Service Hours:
8:30 am to 5:00 pm Pacific time
Monday thru Friday only
Website: www.intexcorp.com
For Residents outside of the U.S. and Canada:
Please refer to the Service Center Locations
©2011 Intex Marketing Ltd. - Intex Development Co. Ltd. Intex Trading Ltd. - Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los
derechos reservados/Alle Rechte vorbehalten.
Printed in China/Imprimé en Chine/Impreso en
China/Gedruckt in China.
®™ Trademarks used in some countries of the world under
license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países
del mundo bajo licencia de/Warenzeichen verwendet in
einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd.
to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd.,
G.P.O Box 28829, Hong Kong & Intex Recreation Corp.,
P.O. Box 1440, Long Beach, CA 90801 • Distributed in the
European Union by/Distribué dans l’Union Européenne
par/Distribuido en la unión Europea por/Vertrieb in der
Europäischen Union durch/Intex Trading B.V., P.O. Box nr.
1075 – 4700 BB Roosendaal – The Netherlands
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising