USER`S MANUAL - Rcom egg Incubator, egg hatcher bird

USER`S MANUAL - Rcom egg Incubator, egg hatcher bird
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
Most Valuable Creation of New Life with "R-COM"
USER'S MANUAL
DIGITAL EGG INCUBATOR
Mx R-COM 50
(Standard Version)
(�
AUTO ELEX CO.,LTD.
(
R-COM 50 1002A
)
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
{lfJ COIi/i 50
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
(�?
�
Contents
How to use R-COM 50
1. Introduction
(1) R-COM 50 Introduction
(2) Safety Precautions
Introduction
(3) Identification of Parts and Composition
(4) Function of Digital Control & How to Operate
2. Before use
(1) How to Assemble the Incubator I Egg-Turning plate
Before use
(2) What is an incubation room?/ Preparation for Incubation
3. Function Settings
Incubation Start & Termination I
Incubator Initialization (Factory Setting) (2) Change Cels.& Fahr.
How
to Set Temperature & Humidity I How to Turn ON, OFF Humidification Function I
(3) How to
Set Abnormal High or Low Temperatue Alarm I How to Set Egg Turning ON, OFF
(1)
Function Settings
4. Incubation
(1)
Humidity &Air Maintenance during Incubation I
Maintenance after Hatching
m
m
m
5. How to Clean
(1) How to Disassemble
(2) How to Clean
6. Product Information
(1) Servicing I Frequently Asked Questions (FAQ)
(2) Troubleshooting
How to Clean
Product Information
m
(3) How to Calibrate the Temperature & Humidity
(4) Specification
r
Incubation
(2) Dew Cond ensat·ion
Mark Explanation
Caution:
Caution mark against a fault that can cause damage, trouble, or failure of incubation.
�
Prohibited
ct)
@
Do not disassemble.
Do not touch.
8
e
9
It is necessary to keep.
Remove the power cord from outlet.
Ground Connection for preventing electric shock.
Tip : References or useful suggestions in using R-COM 50
IA.CAUTIQ__"ii] Warning of actions which may be dangerous or cause damage to the incubator.
DIGITAL INCUBATOR
Contents
D
1. Introduction
(1) R-com 50 Introduction
{lfJ CO/Ill 50
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
R-COM 50
Thanks for choosing the Ream 50 incubator.
The Ream 50 incubator is the first incubator with creditability to have a superior design and function
which help in controlling optimum incubation conditions. It has two sensors, one for detecting
surrounding environments and the other for internal incubator conditions.
The Rcom50 is designed to be easy and simple to use as a customer orientated product,
but please remember that the user's incubation knowledge and proper operation are very important
for the best incubation result.
Therefore, be sure to read this user's manual carefully before you use this incubator.
The Ream 50 offers optimum incubation conditions, but users need to observe and manage
all incubation conditions such as species of eggs, temperature or humidity for each incubation period,
and incubation circumstances .
Features
[Main Features]
* Outer Temp. Sensor included for Automatic Adjustment of Heating rate responding to Incubation Room
Temperature
* Superior design with convenient operation
* Optimum air circulation technique with 5 strong BLOC fans
* Automatic Temp. & Humidity setting and control
* Body locking device
* Water supplement alarm function
* 48 eggs capacity for chicken size eggs ( 116 Quail egg size I 24 Goose egg size)
* Antiblastic Humidification method by heating water, which discourages bacterial growth
* Double-glazed view window for minimizing the influence of outside temperature
* Enhanced reliability by applying Swiss's Sensirion's 3rd generation temperature & humidity sensor
* Strong SMPS application for stable power supply
[Safety Features]
* Alarm and display function of abnormal incubator temperature
caused by sudden fluctuation of ambient temperature
* Incubation data memory function and power outage notification function in case of power failure
* Circulation fan cover for safety and electric safety cut-out switch on the upper main body for safety
* Heater supporter designed for heater tension control and its safety
* Safety cover applied for protecting humidification unit
* Humidification unit durability improved by water proof BLDC fan
* Alarm when water need replenishing
[Easy Features]
*
*
*
*
*
*
*
No need of separate humidification unit as it included in main body
'C or 'F convertible
Easy attachment and detachment of double-glazed viewing window
Universal egg tray for various size eggs
Slide plate with embossed feature for preventing skid
Variable air vent for adjusting air supply
Bottom body designed for easy cleaning
D
1. Introduction
(1) R-com 50 Introduction
DIGITAL INCUBATOR
{lf] COIi/i 50
1. Introduction
(2) Safety Precautions
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
Electrical hazards
Do not use a damaged
power cord or loose
outlet.
Risk of electric shock or fire.
ACAUTION Be careful the details below when you use.
Do not pull the cord when
taking out the power cord,
and keep wet hands away
from connecting plug.
Risk of electric shock or fire.
Setting Cautions
Do not install in dusty or
dirty environment.
Risk of damage or fire within
the incubator.
Do not cover the
ventilating opening.
Inner temperature can rise,
interrupting incubation.
Never pull the plug out of
the outlet during the
incubation period.
Incubation will be interrupted.
Do not twist or crush
electric cord.
Risk of electric shock or fire.
Do not insert multiple
connecting plugs in an
outlet.
Risk of fire or electrical overload.
CAUTION Be careful the details below when you use.
Do not install under the
direct sunlight.
Risk of fire or interference with
the incubation process.
Do not install in moist or
humid environment.
Risk of fire or electric shock.
Do not install in excessively
cold or hot conditions,
cigarette smoke, etc.
Risk of interference with
the incubation process.
Risk of damage to the incubator
case and interference with
the incubation process.
Ensure that the incubator is
installed on a stable surface
away from edges.
Risk of damage to incubator
and eggs anduser from
accidental knocks or drops.
Water will pour out of the Incubator,
and \iew window can be dropped
or damaged.
Please ensure that no
small objects get into
the holes on the incubator.
contact your service
If the incubator sounds
strange or emits smoke
Clean the incubator
thoroughly before storing.
Install away from heat
sources.
Do not tum the incubator
upside down.
Do not use any other
non-standard parts
except those provided.
Risk of damage or hatching
failure.
Children should be supervised
to ensure that they do not play
with the appliance.
Risk of knocking the Incubator
or accidental interference with
the controls.
�@
I 111�
I,�
Do not disassemble or
modify the incubator in
any way.
Risk if electric shock or fire.
Risk of electric shock or fire.
center.
Risk of electric shock or fire.
Cleaning Cautions
Do not spray cleanser
directly on the incubator
surface.
If the incubator requires
repair disconnect from the
power supply and please
oontact to your service center.
Be sure to disconnect the electric cord
from the outlet before cleaning.
Clean the incubator by a
soft cloth with a neutral
detergent.
Brush away dust on the
plug with a dry cloth.
Do not use chemicals like wax,
benzene, alcohol, thinner,
aromatic, or lubricant, etc.
For special cleaning of
inner part per year, contact
to the service center.
If you don't clean the inside of
incubator for a long time, dust
* This appliance is not intended for use by persons (including children) with reduced physical, sensory or
can cause some trouble or a fire.
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
DIGITAL INCUBATOR
1. Introduction
(2) Safety Precautions
a
1. Introduction
(3) ldentific��ion of Parts and
Compos1tlo
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
Identification of Parts
For a clear view of
the Incubation process.
( Double Skin Viewing Window )
Power Connecting (the rear)
For circulating warm air
For connecting
power cord.
11�� L_1/111111 111 111
Universal Tray Divider
Adjust the space of dividers
according to egg size.
11/11]�
Digital Control Center
See description of
the function and operation.
Basic Components
---------------------------
Volt for window assembly
[I
* Can be attached
anywhere for
easy viewing
�ng Divider (10EA)
Sold Separately
Universal Tray
Tray for brooding use
� 1. Introduction
.:.
(3)
Power Cord
ldentific��ion of Parts and
Compos1tlo
User's Manual
Easy function
operation
DIGITAL INCUBATOR
(in
�
COIi/i 50
(4) Function of Digital Control &
How to Operate
1 • Introduction
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
A-COM 50
Setting Humidity Up
Calibration Humidity Up
Humidification working lamp
Heater Lamp
(Lighting when working)
Egg-Turning Lamp
Water Supplement Lamp
Turn on with automatic
egg-turning mode.
(Blink when working)
(Lighting when working)
(Blink with water shortage)
Blink with power failure
- Alarm for water supplement sounds in twice.
(to remove, press SET button) ( First alarm wit h wa ter shortage I Second alarm after 3 ho s
ur )
[ Function Operation & Explanation ]
Function
Temp.
Setting
Humidity
Setting
Egg-Turning
Interval Setting
Egg-Turning
Test
Changing
Cels. & Fahr.
Temp.
Calibration
Humidity
Calibration
Initialization
(Factory setting)
How to OFF
Humidification
Function
Setting Value
Check
Explanation
How to Operate
e� e e
e� 8 e
OLD
OLD
Default setting
every1 hour
(Lamp: ON)
8
once
or
Setting of needed temp.
10
or
Setting of needed humidity.
10
Egg-Turning Interval Setting
as required
10
Egg-Turning Test (once)
10
Changing Cels. & Fahr.
9
2times
5sec.
OLD
CA �
� CA �
5sec.
5sec.
OLD
G
DIGITAL INCUBATOR
3times(OFF)
-..c;;)
... 9..-9
... Lamp
9OFF
HOLD
2 Hours
3 Hours
e+e �
e+ e
8+8
e+
e+ 8
OLD
Page
� CA �
G
4times
every 1 hour
(Lamp ON)
repeat
eor G
e
eor G
e
POWER IN �
�
...
�
How to calibrate temperature.
16
�
How to calibrate humidity.
16
rSt
20%
Initialization
Set Humidity as 20%
9
10
Indication of setting
Temperature and Humidity
* If you want to change setting value, keep pressing "SET" button and change the value.
1 • Introduction
(4) Function of Digital Control &
How to Operate
�
W.
(1) How to A�semble the Incubator I
Egg-turning plate
2 • Before use
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
®
How to Assemble
®
Lock the four locking
buttons at the front and rear
of the incubator.
View Window
@
Back
@
&
Insert the power cord
in the socket at the back
of the main body.
Be careful when you assemble egg turning plate.
Main Body-1
G)
Egg-Turning Plate
� If you do not assemble egg turning place correctly,
it can cuase incubator failure.
� Gear connecting part of egg turning plate
must be on the top side.
D
2 • Before use
(1) How to A�semble the Incubator I
Egg-turning plate
DIGITAL INCUBATOR
(in COIi/i 50
�
(2) What is �n incubation r�om? I
Preparation for Incubation
2 • Before use
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
What's an Incubation Room? I Preparation for Incubation
The Incubation Room is a confined space for setting and operating an incubator.
Because the incubation room environment has a considerable effect on hatch rate, it's recommended to control
the environment for setting up an incubator; there should be little noise and vibration around and temperature
°
ranging 20'C-25'C(68-77 F) with small variation in temperature.
Especially, if there are frequent occasions when the temperature drops suddenly at night, compared with
daytime, be sure to check from time to time and pay attention so that the incubator is not directly exposed to
sunlight during daytime.
0
EJ
&,.
Insert the electric cord in the connecting jack
in the back of the main body and put the main plug into a
socket. The LCD display will light up and show temperature.
Open the watercap and fill the hole with clean water and
refill water after about 5 min. again; up to the limit line
on its inside mark. (If you refill water during the incubation
period, humidity goes down temporarily.)
After filling up with water, never shake or turn over
the main body of the incubator, which would cause water
to spill inside the body and could cause a breakdown.
During incubation period, check the water level
about every three days and refill water, if necessary.
(After you refill water, check again after 5min. and refill again.)
&,.
In case you use the incubator without adding humidification
water or intend to incubate eggs at low humidity under 20%,
you must stop its humidification function. (When using
this function, the alarm for sensing water drop will go out.)
[See the description of humidification function ON/OFF on Page 10.]
* How to turn off Humidification Function : Set humidity level at 20%.
* It is recommended to use distilled water or de-ionised water
to prevent alien matter being introduced
around the humidifying heater.
&. Some gap (about 2mm) around the eggs
is needed for easy egg turning
as shown on the right. �
* When
you use the 'universal rolling divider'
which is sold separately, be careful to
adjust the distance of rolling divider so that eggs do not roll out of
position. Refer to the picture rignt side.
EJ
.&.
Place the eggs to incubate in the egg groove and then close
the view window.
Be careful to close the view window completely;
if not, the temperature and humidity will fail to go up.
The egg to incubate must be a fertilized egg.
(Refer to the guidebook.)
DIGITAl INCUBATOR
2 • Before use
(2) What is �n incubation r�om? I
Preparation for Incubation
.:W.
.:.
(1) Incubation Start &Termination I
Initialization (Factory Setting)
lncubation
_
(2) Changing Cels.&Fahr.
•
•
3. Function Settings
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
How to start incubation
llJiJ,
If you connect the incubator with power cord,
of temp. display is blink with alarm.
second dot
Press SET to remove blink and then it starts incubation with
existing temperature and humidity.
(Factory default setting - Temp.: 37.5°C, Humidity: 45%)
1
llJiJ,
1
•
1
1
Be sure to turn ON egg turning before incubation starts
and turn OFF before 3 days of hatching. At this time, it's
recommendable to raise humidity up to 60-70%.
[Refer to Egg Turning ON/OFF on Page 1 O.]
q{J There can be some smell the first time you use the incubator, that is normal.
q{J !Power Failure Notification!: When firstly input power, or power failure during incubation,
second dot" . of temp. display is blink with alarm. Press SET to remove.
11
How to terminate incubation
llJiJ,
After all eggs are hatched, you should REMOVE
the power cord for incubation termination.
(The incubator has no separate power switch.)
How to initialize incubator
(Returning to factory default settings)
llJiJ,
1JJiJ,
It is for returning to the factory default setting.
It is for initializing the incubator setting or calibration to the factory settings when you handle the incubator
improperly so that the value has changed. Unplug the power supply and hold SET button and re-plug
the power supply as shown on picture. Then, rSt will show on the display, and the incubator will be
initialized to factory setting.
Re-plug the power supply
+
-----
l)l)lll
m
",St'' will show on the display as below,
� and the incubator initialize to factory setting.
--
How to change Cels. & Fahr.
llJiJ,
Press
e e
and
buttons at the same time
and CA will show on Temp. display.
Then press
@ button, it will change
as shown on the right.
9
.
.
3. Function Settings
(1) Incubation Start &Termination I
lncubat(on Initialization (Factory Setting)
(2) Changing Cels.&Fahr.
DIGITAL INCUBATOR
.
{lf] Ca"" 50
.
3. Function Settings
(3) HowtoSet Temperature & Humidity I Howto Turn ON/OFF
Hum1d1ficationF unct1on/HowtoSetAbnormalH1ghorlow
TemperatueAlarm I HowtoSet Egg Turning ON, OFF
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
How to Set Humidity
How to Set Temperature
.._ In a state of
e
e
e
.._ In a state of
button being pressed,
adjust the temperature you want with
e
or
e
button being pressed,
adjust the humidity you want with
button. Temperature setting will be
e
e
button. humidity setting will be
e
completed when you remove your finger
completed when you remove your finger
from the
from the
button, and the present
P
button, and the present
humidity of the incubator inside will be indicated.
temperature of the incubator inside will be indicated.
q{J
or
If you set the incubator under a direct ray of
light or too cold spot, the incubator temperature
can be higher or lower than setting temperature.
.._ Be sure to set humidity 65%-70% from 1-2 days
before hatching.
q{J
If you press SET button, the present setting
temperature and humidity will be indicated and,
if you remove your finger from the button, the present
inner temperature and humidity indicated.
Temperature and humidity can be different from
normal setting levels according to the surrounding
environment. (Refer to a incubation guidebook
which is supplied separately.)
How to Turn ON/OFF Humidification Function
.._ In a state of SET button being pressed, press HUMI- button to adjust humidity at 20% and, then, humidification
function will be OFF. On the contrary, if you adjust humidity above 20%, its function will be ON.
How to Set Abnormal High or Low Temperatue Alarm
.._ What isAbnom,al H igh or Low TemperatureAlarm?
It is alam, soulds when incubator temperature is higer or lower than setting value because of various reasons such as
room temperature change or disorder of temperature controlling system.
* How to Set
e�
Set required
high range with
3Sec.
UP I DOWN button
°
�e�
I
Set required
low range with
Save setting and
pass to
low humi. set
UP I DOWN button
°
°
�e
Save setting and
pass to current
temp. & humi.
indication
°
* Max. abnonnal temp. alann limit (0.0 C - 5.0 C Default Setting:2.0 C) * Min. abnonnal temp. alann limit (0.0 t - -5.0 C Default Setting:-3.0 t)
How to Set Egg Turning ON/OFF
e
e
.._ Egg Turning Test: If you press
e
button for
about 5 seconds, egg turning test will be effected once.
=
.._ In a state of
button being pressed, press
button then the setting will be changed as required.
&,
Once (Lamp ON)
2Times (I.amp ON)
3Times (Lamp OFF)
41imes (Lamp ON)
Egg tuming lrKerval : 2 hours Egg turning Interval : 3 hours Egg tuming Interval : OFF Egg turning Interval : an hour
Be sure to set TURNING OFF 3 days before hatching.
DIG ITAl I NCU BATOR
3. Function Settings
(3) How to Set Temperature & Hum1d1ty I How to Tum ON, OFF
Hum1d1ficat1on Function I How to Set Abnormal High or Low
Temperatue Alarm I How to Set Egg Turning ON, OFF
IIiJ
4 . I ncu b at•10n
(1)Humidity&AirMaintenance duringlncubation/
Maintenance aft_erHatching
(2) DewCondensation
{lfJ CO/Ill 50
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
Humidity & Air Maintenance During Incubation
11J,,
When hatching, humidity should be relatively high to prevent
the thin membrane from drying out or hardening before hatching.
11J,,
When hatching, it's recommended not to open the lid often.
This is because if you open the lid often humidity will be rapidly
decreased and it will take a long time to regain the proper humidity.
* If incubatior temperature is higher than 37 'C and room temperature is low,
it may be difficult to maintain humidity of over 70%. There may be some
difference of humidity about :!:5% according to the external environment ,
but no problem with hatching.
11J,,
*
It's very important to maintain humidity higher 1-2 days before hatching
than the early and middle incubation periods.
Humidity requirements during incubation are 45-55% for waterfowl,
40-45% for poultry and 35-45% for parrot, in general. One day before
hatching, all kinds of birds need about 65% humidity and sometimes
need higher than that. However, in areas of high ambient humidity,
lower levels of humidity may be needed during incubation
Air Controlling Lever : Outer fresh air can be flowed into incubator inside
without affecting insulation.
When eggs start hatching, open air controlling lever either fully or half-open.
Maintenance after Hatching
11J,,
Because newly-born chicks just after hatching have little protection against cold, a brooding room should certainly be
prepared in advance for them. In case there is no separate brooder prepared, you may let them stay in the incubator
for one day or more after hatching. If you move them to an brooder or brooding box, the inner temperature should be
kept at 35'C-37'C .
For the production method of a simple brooder, please refer to our website www.r-com.co.kr.
11J,,
As there is some difference in chick feed for each kind of bird, so it's desirable to obtain useful information
about the chicks before hatching.
A
*
If feather of chicks gets wet, chicks' body temperature falls down, and, if then,
you must immediately dry by hair dryer.
Dew Condensation
This is a naturally occurring phenomenon when there is a significant
difference in temperature between inside and outside of the incubator
during incubation period. If this occurs, water may form in inside
bottom of the main body of the incubator(bottom part).
GI
4 " I nCU b at•IOn
(1)Humidity&AirMaintenance during Incubation I
Howto manage atter hatch
(2) DewCondensation
DIGITAL INCUBATOR
5. How to Clean
(1) How to Disassemble
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
� Pull out the electric cord from the connecting jack and
also take out the plug from the outlet.
Don't turn off the power soon after using the incubator,
as this may cause a break down due to moisture left inside
the main controller. At this time, it's better to firstly remove
the water inside of the incubator and dry by operating it for
1 hour and then turn it off or open the view window and dry
it naturally for 2-3 hours and, then, re-operate it, which may
lengthen the life time of incubator.
(Set humidification function OFF. I Refer to the page 10.)
How to disassemble and
clean the incubator
0
Unlock and remove the locking buttons for four parts
at the front and back of incubator by pulling them forward.
The bottom part of incubator should be thoroughly cleaned with water
and dried. The upper part should be naturally dried in the well-ventilated
place for about one day to remove moisture left inside of the incubator
after hatching thoroughly.
A
Don't clean the product with organic solvents such as benzene,
thinner, etc. which may cause deformation or decoloration
of the plastic parts.
� When using humidification function, a lot of alien matter sticks
to the humidification heating element®· This may not cause failure,
but when terminating incubation please clean the humidifying heater
lightly with a soft brush.
� If you place the main body{upper part) on the floor,
please don't let the humidification heating part touch with the floor.
A
A
If you inflict impact on the humidification heating part or scrape it
with a sharp instrument, the humidifying heater will be damaged.
You are recommended to use distilled water or de-ionised water
to prevent alien matter being caught in around the humidification
heating part®·
DIGITAL INCUBATOR
5. How to Clean
(1) How to Disassemble
m
5. How to Clean
(2) How to Clean
{lfJ Ca"" 50
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
Start the vacuum cleaner to remove the dust as shown
on the right and thoroughly shake out the minute dust with
a fine brush.
r"'\
� If the incubator goes through incubations several times,
feather, dust, shell, etc. accumulate inside the main body,
which may cause a break down, so be sure to clean
the product before storage.
If you finish cleaning the incubator, reassemble it in the reverse
order of disassembly. Wipe out outside the main body with a
wet cloth and dry it in a cool and well-ventilated place before
storage.
� [Refer to How to assemble on Page 7.]
_& Don't clean the product with organic solvents such as benzene,
thinner, etc. which may cause deformation or decoloration.
IE)
5. How to Clean
(2) How to Clean
DIGITAL INCUBATOR
{in
�
CO 11/1 SQ
6·
p rod UCt I n,orma
.&
t"10n
(1) Servicing I
Frequently Asked Questions (FAQ)
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
Servicing
All our R-Com digital incubators of Autoelex Co., Ltd. are made by precision systems under
strict quality control. But occasionally some defective products are found on the way of their
distribution. If any problem occurs, then please contact Autoelex service center or distributors
in your country. We will do our best to solve the problems, if any, for you.
This product is designed in modular mode, so for its repair, if any, a qualified person can replace
the part concerned with ease.
Frequently Asked Questions (FAQ)
Troubles
In case hatching rate
is low
Expected Causes (Possibility)
�When the egg is an unfertilized egg.
�Getting infected by germs
�Wrong incubation setting
� Health condition of mother bird
� Improper egg turning
Countenneasures
� Check possibility of egg
surviving
� Disinfect the incubator
� Check all settings of incubator.
Especially, check them focusing
on the temperature.
� Review care of health of mother bird.
� Check if egg turning is normal.
When a chick hatches
out earlier than
expected or a
deformed chick
hatches out
�Setting temperature too high
� Egg turning was not operating normally
� Lower temp. setting of the
incubator about 0.5'C (1 'F)
ex) 37.5'C � 37.0'C
� Check if egg turning function is OFF
When a chick hatches
out later than
expected
�Setting temperature too low
� Raise temp. setting of the
incubator about 0.5'C (1 'F)
� ex)37.0'C � 37.5'C
When hatching dates
are so different from
each egg
(When all chicks don't
hatch out at the same
time but over a long
period)
� Eggs stored for different lengths of time
� Diffferent incubation temperatures
� Set limits to egg storage time properly
� Check Temperature difference
in the incubator.
(sunlight, temp of incubation room, etc.)
When intending to
hatching various eggs
at the same time
� Incubation days are different,
so hatching rate falls down.
� Mark hatching date on eggs and
move them to other incubator
(brooder) just on the marked date.
� In case of putting in many eggs
at the same time, it's convenient
to prepare a spare incubator available
as a brooder
DIGITAl INCUBATOR
6 · P rod UCt I n,orma
,
t·10n
(1)Servicing/
Frequently Asked Questions (FAQ)
�
Wilil'
6. Product Information
(2) Troubleshooting
{lfJ Ca"" 50
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
Troubleshooting
CIRCUMSTANCE
ITEMS TO BE CONFIRMED
SOLUTIONS
No signs of power
to the incubator.
� Check electric cord is property connected.
� Check if there is a power outage.
� Check whether the plug is damaged.
� Connect the cord again.
� Check the main socket with any other
electric appliances.
� Try to insert to another outlet.
Temperature will
not go high enough.
� Check your setting temperature.
� Check the air circulation FAN is working.
� Initialize the incubator.
[Refer to the page 9]
� Set the temperature as required.
Alarm sounds with
HI indication
� Check if room temperature is too high
� Check if incubator is exposed to the direct
rays of sun
� Adjust room temperature between 20'C and 25°C.
� Install incubator without the direct rays of sun
� Return incubator to factory setting [Refer to page 9]
Alarm sounds with
LO indication
� Adjust room temperature between 2o·c and 25'C.
� Check if room temperature is too low
� Check if incubator heater(temperature controlling- � Place thermometer inside of incubator and check
system) is normally working
if setting temperature is correct
� Return incubator to factory setting [Refer to page 9]
Humidity will not
go high enough.
� Check your setting humidity.
� Close the view window again after checking.
� Initialize the incubator. [Refer to the page 9]
� Supply water.
� Set the humidity again as required.
The machine makes
some noise.
� Check if there is any hatching debris such as
feather or eggs-shell in the incubator FAN.
� Take out the plug out of the outlet and
disassemble the main body and clean
around the air circulation fan with brush.
Egg-Turning fails
to work.
� Check that the Egg-turning stoppage is not
activated. (Egg-turning lamp lighting)
� Check that there are no foreign items on the
egg turning tray.
� Check if egg turning plate is assembled correctly.
[Refer to the page 7]
� If you need to turn the eggs, you can
manually re-start egg-turning.
� Unplug the power supply and
disassemble the main body for cleaning
the egg turning tray and gear.
� Assemble egg turning plate as the picture on page 7.
Dew foams in
the incubator.
� Check the incubator is not placed
too cold circumstances.
� When you turn OFF incubator and then
turn on.
� Move the incubator to where the ambient air
temperature is over 20 t.
(abnormal high temp.)
(abnormal low temp.)
- II is normal that the machine
emits some sounds because
ij uses air circulation fan
for working.
Water leaks from
the machine.
� Check that you have not overfilled the incubator.
� Check that the incubator placed on inclined
surface.
� Check if ii is Dew condensation
� Take the power plug out of the outlet, and
disassemble the main body for cleaning
around the air circulation fan with brush.
� Dew mndensation is normal.
� Dry 1he incubator mmplete� under well ventilated �ace.
� Do not fill water over LIMIT indication.
� Place incubator under a level surface.
.&. Hatching result could be affected with various factors, and manufacturer do not have
m
any responsibility for loss of eggs or birds.
6. Product Information
(2) Troubleshooting
DIGITAL INCUBATOR
6 . p rod UCt I n1.cormat"10n
{in
�
COIi/i SQ
(3) How to Calibrate
theTemperature&Humidity
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
As this incubator was made with the optimum conditions set at the factory,
you don't need to calibrate the temperature or humidity before
use except for sensitive birds.
Operate incubator for an hour before calibration for temperature stabilization.
And then, observe the temperature or humidity at several position
above 15mm of the egg tray mat with your thermometer, and
calibrate with average value.
Low priced them,ometers or hygrometers which you can easily purchase
from the market have large deflection of measurement.
This could cause hatching failure, and it is recommended to use highly
precise them,ometer or hygrometer.
Humidity Calibration
Temperature Calibration
.8··, ·
"8
e
e
""""'""O
HEATING
TURNING ON
e
5Sec.
button at the same time.
button and
� Press
CA sign will show on the Temp. display, and after 5sec.
pressing the buttons, the display will blink.
'"e
e
e
If you want to raise incubator temperature 0.5 ·c
higher, you should calibrate o.s·c lower at temp.
calibration mode.
.o
"8
e
c!!)ca1111sa
TEMPERATUlE
H!cATING
.HJ\'IOIFl8AT8N
Q WAltHl:1,1' �
e
o�
8
c!!)ca1111sa
�
""'"°'"'
O • RMDFICATIO�
TURNING ON O
O \'/ATE� EIIPTV
HEATING
e
e
If you want to raise incubator humidity 5% higher,
you should calibrate 5% lower at humidity
calibration mode.
.8···
O .,"
8
"'
"'"'"'""
HtAIING
IURNINGON
e
Q
o.
D v",
8
�CDllll50
"""'°"'
• H..MDFICATIO�
O O WAlt�tl,Wlv
DIGITAL INCUBATOR
DIGITAL INCUBATOR
� If you press
button, the setting will be
(If you don't press any key,
completed.
it automatically set after 5 Sec.)
(After Calibration>
�
DIGITAL INCUBATOR
button or
� Calibrate the humidity with
button. ( Calibration extent : :!: 20% )
HJMmY
Q
,,J,,,,;: �
• �LMl)FICATIO�
O O WATE� EMPTY
DIGITAL INCUBATOR
ov.
8
IUHNINGON Q
�
button at the same time.
� Press
button and
CA sign will show on the Humidity display, and after 5sec.
pressing the buttons, the display will blink.
.ee•P•
button or
� Calibrate the temperature with
button. ( Calibration extent: :!: 9.9'C )
o�
c!!)ca1111sa
button, the setting will be
� If you press
(If you don't press any key,
completed.
it automatically set after 5 Sec.)
If you can not rely on your thermometer or hygrometer, you can initialize the incubator to factory setting.
(Refer to the page 9)
DIGITAl INCUBATOR
•
6. Product Information
(3) How to Calibrate
theTemperature&Humidity
m
6. Product Information
{lfJ Ca"" 50
(4) Specification
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
Specification
1-1 NAME : DIGITAL INCUBATOR R-COM 50
1-2 MODEL NO. : MX 50 (STANDARD)
[ Specification ]
Power
AC 1oov-12ov, so/&OHz
AC 220V-240V, 50/60Hz
Temp. limits
20.0'C - 42.0'C
Working Temperature
ldeal:20'C - 25'C
Humidity Limits
20%- 70%
( It can be changed according to the conditions )
Power Consumption
Max. 120W (Average 65W)
Egg-Turning Interval
Various according to the tray
Capacity
For all size egg : Various sized egg incubation is:
available
Small
:
: 116 eggs ( Quail egg size)
:
Standard
: 48 eggs ( Chick egg size)
Large
: 24 eggs ( Goose egg size) :
Net Weight
6.65kg(lncluding Universal Tray)
Min. 15'C I Max. 30'C
Universal tray
Small egg tray (option)
Standard egg tray (option)
Large egg tray (option)
Gross Weight
Size
(W)633 x (L)523 x (H)171 (mm)
Fuse Standard
250V 2.0A ( 0 5 x 20mm)
(Included)
9.5kg
* Register your product Serial No. on our website for free 2 years gurantee.
* Refer to website for how to register. (Free 1 years gurantee in case not registerd.)
� If you are new member of Rcom website,
1. Visit www.r-com.co.kr
2. Click English version
3. Click "REGISTER" at the left side of page.
4. Full in your information according to description.
5. Register completed.
ID
6. Product Information
� If you already registered your information on Rcom website
1. Log on www.r-com.co.kr
2. Click "Member information change" at the left side of page.
3. Check "YES" to the question "Did you purchase Rcom products?"
4. Fill in your information according to description.
(4) Specification
DIGIT AL INCUBATOR
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
I
Rcom Mx 50 Incubator Sales & Service www.RcomCo.com
R-COM is designed for user's easy and convenient use.
It can be changed without notice for improvement in performance,
design,treatment, and software, etc.
www.RcomCo.com
(
sEL LER
..___ _ _ _ _ __)
( MANUFACTURER )
•COMPANY: #612 DukAm-RI, JuChon-Myeon,
GimHae-City, GyeongNam, KOREA
www.RcomCo.com
Rcom is the Best Design with High Quality, Value, and Performance!
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising