1100XH High Power Wireless Receiver
Installation Guide
1100XH High Power Wireless Receiver
Description
The 1100XH High Power Wireless Receiver provides two-way, supervised communication using 900 MHz frequency
hopping-spread-spectrum technology. The receiver provides additional transmit and receive amplification for improved
performance at greater distance or harsh building environments. The receiver provides up to 500 wireless zones. Refer to
the panel installation guide for number of available wireless zones. The system is designed so only one 1100 receiver is
used per panel.
Compatibility
•
•
•
XR500 Series panels using firmware Version 113
or higher
XR100 Series panels
XR150/XR350/XR550 Series panels
Panel Receive
Panel Transmit
Status
RF Receive
RF Transmit
What is Included
The receiver includes the following items:
• One Model 1100XH High Power Wireless Receiver
• Hardware pack
Installing the Wireless Receiver
LEDs
Mounting Hole
Locations
Mounting Screw
Shoulder Washer
Selecting a Location
Tamper
Switch
1
1
Panel Receive
Panel Transmit
Status
RF Receive
RF Transmit
Squeeze
to Remove
Cover
The 1100XH High Power Wireless Receiver contains
additional transmit and receive amplifiers to enable
greater distances for 1100 Series operation. The
additional gain introduced by this amplification may inhibit
proper communication with 1100 Series transmitters located
within 4 feet of the receiver. This distance may be 8 feet when
using the 1121 or 1125 PIR, 1160 Series Smoke Detectors or 9000
Series Keypad.
Y1
U8
2-pin Header
U10
L17
Squeeze
to Remove
Cover
1
Choose an optimum location to mount the receiver. A
location should be selected that is centrally located
between the 1100 Series transmitters used in the
installation. Install the receiver away from large
metal objects and at least 1 foot away from the panel
enclosure. Mounting the receiver on or near metal
surfaces impairs performance. Do not use shielded wire
between the panel and receiver. When selecting the
proper mounting location of a transmitter, refer to the
LED Survey Operation section.
U11
PANEL
J4 Connects
To Panel
Figure 1: Receiver PCB
Tamper Switches
The 1100XH is equipped with a case tamper and a wall tamper.
A two position header is provided to disable the wall tamper. To
disable the wall tamper, place the jumper across the two pins of
the header. If wall tamper is required, place the jumper over just
one pin for storage.
Mounting the Receiver
1. Remove the cover from the plastic housing by squeezing
both sides toward each other.
2. Secure the receiver to the wall ensuring that the wall
tamper switch makes proper contact with the wall. Use the
supplied screws in the mounting hole locations as shown in
Figure 1.
3. Snap the cover back on the unit making sure the case
tamper spring is installed on the tamper switch. The panel
immediately recognizes the 1100XH Receiver if the panel is
programmed with a house code.
Wall
Tamper
Figure 2: Wall Tamper location
Wireless Bus Connection
The 1100XH easily interfaces with the XR500/XR500FC and XR100/XR100FC Series panels using the on-board DMP Wireless
Bus connection (J22). On XR150/XR350/XR550 Series panels, the 1100XH interfaces using the on-board X-Bus connection
(J13). The receiver can be hard-wire mounted up to 100 feet from the panel enclosure using 22 AWG wire or 250 feet using
18 AWG wire. This wire restriction is due to the higher current draw needed for the high power RF amplification.
If additional wire distance is required, the 1100XH can be connected to the Wireless Bus through a 710 Bus/Splitter module
and powered by a 12 VDC power supply (DMP Model 505-12). Please see the 710 Installation guide (LT-0320) for maximum
distance information from the panel to the 710 module.
Note: The 1100XH High Power Wireless Receiver cannot operate if connected to the Keypad Bus.
Harness Connection XR100/XR100FC/XR500/XR500FC panels
1. Install a jumper across the header pins next to the letter “X” on the XR100/XR100FC/XR500/XR500FC panel J23
header to enable on‑board DMP Wireless operation.
2. Connect the J4 header on the 1100XH to the XR100/XR100FC/XR500/XR500FC panel J22 LX header.
3. After power-up, briefly reset the panel using the J16 jumper to activate wireless zone operation.
4. In System Options, program the House Code (1-50). In Zone Information, program the wireless zones.
XR100/XR100FC/XR500/XR500FC
Series Panel
RS-232
J22
LX
Red
X
XMT - Transmit LED
REC - Receive LED
Output 1
J10
Battery
Start
Tamper
Switch
Output 2
J2
K6
J8
PROG
Out1 Out2
J23
Power R
LED
L
1100XH
Receiver
J21
1
1
Panel Receive
Panel Transmit
Status
RF Receive
RF Transmit
K7
Y1
U8
2-pin Header
U10
1
2
3
4
5
6
7
8
9
10
11
12 13
14
1
L17
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
Z3 G
PANEL
U11
15 16
Red
Yellow
Green
Black
Can be extended
up to 100 feet
from the panel
using 22 AWG
or 250 feet
using 18 AWG
Figure 3: XR100/XR100FC or XR500/XR500FC DMP Wireless Bus Connection
Harness Connection XR150/XR350/XR550 panels
1. Connect the J4 header on the 1100XH to the XR150/XR350/XR550 panel J13 XBUS header.
2. After power-up, briefly reset the panel using the J16 jumper to activate wireless zone operation.
3. In System Options, program the House Code (1-50). In Zone Information, program the wireless zones.
Power
LED
XR150/XR350/XR550
Series Panel
1100XH
Receiver
Battery Start
Tamper
Switch
1
1
XMT - Transmit LED
Panel Receive
Panel Transmit
Status
RF Receive
RF Transmit
REC - Receive LED
Y1
U8
2-pin Header
U10
1
L17
U11
Red
Yellow
Green
Black
PANEL
Can be extended
up to 100 feet
from the panel
using 22 AWG
or 250 feet
using 18 AWG
Figure 4: XR150/XR350/XR550 DMP Wireless Bus Connection
Digital Monitoring Products
2
1100XH High Power Wireless Receiver Installation Guide
1100XH Receiver Operation
The 1100XH receiver automatically sends the panel house code to wireless transmitters when the unique transmitter serial
number is programmed into the panel. The house code identifies the panel, receiver, and transmitters to each other. The
receiver only listens for transmissions using the specified house code and/or programmed transmitter serial number.
Note: When setting up a wireless system, it is recommended to program zones and connect the receiver before installing
batteries in the transmitters.
Transmitters can be programmed for supervised operation. When programmed as supervised, the transmitter must
communicate with the receiver within the programmed number of minutes. If the transmitter fails to communicate, the
panel displays a missing condition.
Note: When a receiver is installed, powered up, or the panel is reset, the supervision time for transmitters is reset. If the
receiver has been powered down for more than one hour, wireless transmitters may take up to an additional hour to send
a supervision message unless tripped, tampered, or powered up. This operation extends battery life for transmitters. A
missing message may display on the keypad until the transmitter sends a supervision message.
When any wireless zone programming is changed in the panel, receiver zone programming is updated. At that point, all
wireless zones display as normal for approximately one minute, regardless of the actual state of the contact.
1100XH LED Operation
Six LEDs display receiver operation and activity. Refer to the table below as required.
Label
Operation
PNL RX
Flashes yellow to indicate data is being received from the panel.
PNL TX
Flashes green to indicate data is being sent to the panel.
STATUS
Steady red to indicate memory upload. Off when upload is complete.
RF RXD
Flashes yellow to indicate data is being received from a transmitter.
RF TXD
Flashes green to indicate data is being sent to a transmitter.
Transmitter Survey LED Operation
DMP 1100 Series transmitters provide Two-way (transmit acknowledge) operation. This advanced data protocol allows each
transmitter to confirm that each of its messages (alarm, checkin, tamper, low battery) are received and acknowledged
by the 1100 Series receiver. The confirmation is indicated visually by use of an LED on each transmitter. This Survey LED
should be used during installation to test each transmitter for proper operation. A full definition of the Survey LED follows.
The red LED on an 1100 Series transmitter turns on when the processor wakes up to send a message. Then after a series of
communication steps are completed (successful or not), the LED turns off when the processor goes back to sleep.
99.9% of the time the processor is asleep in normal operation. The following list summarizes various indications that can
be observed on the LED and a definition for each. Note this is for a single message. Example, pressing and holding the
tamper switch.
Single 1/16 second flash
• Processor wakes up
• Transmitter receives immediate synchronization from receiver
• Transmitter transmits
• Transmitter receives immediate acknowledgement from receiver
• Processor goes to sleep
Single Pulse greater than 1/16 second but shorter than 8 seconds
• Processor wakes up
• Transmitter receives synchronization from receiver - possibly not immediate
• Transmitter transmits
• Transmitter receives acknowledgement from receiver - possibly not immediate
• Processor goes to sleep
Steady for 8 seconds
• Processor wakes up
• Transmitter never receives synchronization from receiver, or might receive synchronization
• Transmitter transmits if synchronization was received
• Transmitter never receives any further data from receiver
• Processor times out and goes to sleep
Multiple short flashes
• Processor wakes up
• Transmitter receives synchronization from receiver
• Transmitter transmits
• Transmitter receives data from receiver, but not a valid acknowledgement
• Processor briefly goes to sleep
• Entire sequence is repeated, each short flash indicates a cycle
1100XH High Power Wireless Receiver Installation Guide
Digital Monitoring Products
3
Troubleshooting Using the Transmitter Survey LED
If a transmitter is unable to reliably communicate a message to the receiver, or is reported as missing, the Survey LED can
be used to help diagnose the issue. If the missing transmitter cannot be explained by obvious reasons such as a damaged
transmitter, failed battery, or changes in building construction; then the Survey LED should be used.
To use the Survey LED operation to help diagnose a field issue, complete the following steps on an 1100 Series transmitter.
Repeat the following sequence 5 times and write down the LED operation for each tamper switch action.
• Press and hold the tamper switch
• Observe the LED until it turns off for at least 5 seconds
• Release the tamper switch
• Observe the LED until it turns off for at least 5 seconds
You now have observed the LED 10 times. Based on the results you have recorded use the list below to assist in
troubleshooting.
LED turns on a single time for less than 1 second 8 to 10 times.
• System is working properly
LED turns on for more than 1 second 3 to 9 times.
• The transmitter or receiver needs to be relocated
LED turns on for more than 1 second all 10 times.
• The receiver is not turned on, or is not operating
• The transmitter is not programmed into the receiver
• The transmitter or receiver needs to be relocated
LED flashes multiple times with a single tamper press or release 3 to 10 times.
• The transmitter or receiver needs to be relocated
LED never turns on.
• The transmitter battery is dead
• The tamper switch is being pressed or released too quickly
• The tamper switch or other part of the transmitter is broken
LED stays on constantly and is dim
• The transmitter battery is almost dead
• The transmitter is broken
General Wireless Troubleshooting
If ALL wireless devices do not operate, refer to the following checklist:
• Verify the receiver is an 1100XH and the panel is an XR500 Series with firmware Version 113 or higher or an
XR100/XR100FC/XR500FC, or XR150/XR350/XR550 Series panel.
• Verify the XR100/XR100FC/XR500/XR500FC panel J23 jumper is in the “X” position and the J4 connector from the
receiver is connected to J22 of the panel.
• Verify the J4 connector from the receiver is connected to J13 on the XR150/XR350/XR550 panel.
• Briefly reset panel using J16 jumper to activate wireless operation and wait one minute to test wireless zone(s).
• Verify the House Code (1-50) is programmed in System Options.
• Verify appropriate zone numbers are assigned as wireless zones.
• Verify that the panel XMIT and REC LEDs alternately flash on and off at a rate of 1/4 second each. If the LEDs are On
steady or Off, the panel and receiver are not communicating properly. (See Figure 3 and 4).
• Verify the 1100XH LEDs operate correctly as listed in 1100XH LED Operation.
• Verify transmitters have batteries correctly inserted.
Digital Monitoring Products
4
1100XH High Power Wireless Receiver Installation Guide
Transmitter Supervision Time
For UL Listed installations, program the transmitter supervision time in panel zone programming as listed in the following
table. Refer to the panel programming guide for complete wireless programming information.
UL Listing
UL 1023 Household Burglary Alarm System Units Accessory
UL 636
UL 634
Holdup Alarm Units and Systems Accessory
Connections and Switches for use with Burglar Alarm
Systems Accessory
UL 639
Intrusion Detection Units Accessory
UL 365
Police Station Connected Burglar Accessory
UL 609
Local Burglar Alarm Units and System Accessory
UL 1076 Proprietary Burglar Alarm Units Accessory
UL 1610 Central Station Burglar Alarm Units Accessory
UL 268
Smoke-Automatic Fire Detectors
Listed Accessories
1100R Repeater
1101/1102/1103/1106 Universal
Transmitters
1127W/1127C PIR Motion Detector
1135 Wireless Sounder
1142 Two-Button Hold-Up Transmitter
9060/9063 Wireless Keypad
1142 Two-Button Hold-Up Transmitter
1100R Repeater
1101/1102/1103/1106 Universal
Transmitters
1100R Repeater
1127W/1127C PIR Motion Detector
1100R Repeater
1103 Universal Transmitter
1100R Repeater
1103 Universal Transmitter
1100R Repeater
1103 Universal Transmitter
1100R Repeater
1103 Universal Transmitter
1135 Wireless Sounder
9060/9063 Wireless Keypad
1100R Repeater
1161/1162 Residential Smoke Detectors
1164 Wireless Synchronized Smoke
Detector
1165/1165H/1165HS Commercial Smoke
UL 521
Heat Detectors for Fire Protective Signaling Systems
1100R Repeater
1183-135F/1183-135R Heat Detector
UL 985
Household Fire Warning System Accessory
UL 864
Fire Protective Signaling
1100R Repeater
1135 Wireless Sounder
9060/9063 Wireless Keypad
1103 Universal Transmitter
1100R Repeater
1184 Wireless Carbon Monoxide Detector
UL 2075 Gas and Vapor Detectors and Sensors
Supervision
Time
60
60
60
60
60
60
60
60
3
3
240
3
240
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note: The 1100 Series wireless system is a two-way supervised wireless design. It is compliant with FCC rules as they pertain
to 900 MHz Spread Spectrum devices. In rare instances it has been observed that certain 900 MHz cordless telephones may
occasionally experience a clicking sound on the telephone while in use. If this occurs, it may be resolved by selecting a different
channel on the cordless telephone, or replacing the cordless phone with a different brand or model of 900 MHz telephone or
other cordless telephone.
To comply with RF exposure requirements, a minimum distance of 20cm must be maintained between the antenna and all persons.
1100XH High Power Wireless Receiver Installation Guide
Digital Monitoring Products
5
Attention! Older Cordless Telephones
Your wireless alarm system is comprised of a state-of-the-art two-way secure network created by sophisticated transmitters and
receivers. It is compliant with all FCC rules as they pertain to 900 MHz Spread Spectrum devices which require devices to share the same
frequencies. This creates a possibility of interference with other devices in your home.
It has been reported that certain older 900 MHz cordless telephones may on rare occasions experience interference (an audible clicking
sound) while in use. (This may also occur with some 2.4 GHz and 5.8 GHz telephones as many still use 900 MHz frequencies). If this
occurs on your cordless telephone, it may be resolved by selecting a different channel on your telephone. If your telephone does not
have this selection, it can also be resolved by replacing your old cordless telephone with a DECT 6.0 cordless telephone.
What is DECT 6.0?
DECT 6.0 (Digital Enhanced Cordless Telecommunications) is the current standard for cordless telephones, and it provides several benefits
over 900 MHz, 2.4 GHz and 5.8 GHz systems.
• No More Interference - unlike older cordless technology, DECT 6.0 telephones are virtually immune to household interference,
and vice versa. If you have a wireless computer network in your home, DECT 6.0 won’t disrupt internet use.
• Encrypted Privacy – DECT 6.0 has a layer of security that older cordless telephones just don’t have. As information and identity
theft is on the rise, DECT encryption helps keep your personal communications safe.
• Call Quality - Extra security isn’t just for safety; it gives you clearer calls without crossover traffic.
• Battery Life - A DECT 6.0 phone will last as much as 30% longer than a 5.8 GHz phone.
More information can be found on DECT technology at www.DECT.org.
DECT 6.0 Cordless phones can be found at any major retailer including: Wal-Mart™, Target™, Best Buy™ & Radio Shack™.
Listed Compliance Specifications
Commercial Fire
Transmitters must be programmed as supervised. Refer to the Transmitter Supervision Time table for the supervision time.
The maximum line impedance of the 4-wire bus is 16.2 Ohms for 1000 feet.
The recommended wire gauge for panel to receiver connection is 22 AWG.
After all transmitters are in position, the WLS option of the panel’s Walk Test must be operated and all transmitters programmed
for Fire (FI) or Supervisory (SV) must show that their checkin message was received. Refer to the panel programming guide for
Trip Counter for DMP Wireless check-in Test (WLS) which describes that both numbers of the counter must match. If not and a
failed wireless zone is displayed at END, decrease that transmitters range with the receiver and perform the WLS Walk Test again.
The wall tamper must be enabled for commercial fire applications.
8.0 to 14 VDC
240mA
720mW
905-924 MHz
Certifications
4.65” L x 3.1” W x 1.4” H
8.6” H
White
Flame retardant ABS
Patents
U. S. Patent No. 7,239,236
800 - 641 - 4282
ANSI/UL 365
Police Station Connected Burglar
ANSI/UL 609
Local Burglar Alarm Units and Systems
ANSI/UL 634
Connections and Switches for use with
Burglar Alarm Systems Accessory
ANSI/UL 636
Holdup Alarm Units and System
ANSI/UL 639
Intrusion Detection Units Accessory
ANSI/UL 1023
Household Burglar Alarm System Units
ANSI/UL 1076
Proprietary Burglar Alarm Units
ANSI/UL 1610
Central Station Burglar Alarm Units
ANSI/UL 985
Household Fire Warning System
ANSI/UL 864
Fire Protective Signaling Systems
California State Fire Marshal (CSFM)
FCC Part 15: CCKPC0114
New York City 1100 Series Wireless (FDNY COA #6167)
Industry Canada: 5251A-PC0114
Intrusion
•
fire
•
Access
•
Networks
www.dmp.com
2500 North Partnership Boulevard
Designed, Engineered and
Assembled in U.S.A.
S p r i n g fi e l d , M i s s o u r i 6 5 8 0 3 - 8 8 7 7
15255
Operating Voltage
Current Draw
RF Power Rating
Frequency Range
Dimensions
Receiver Housing
Antennas
Color
Housing Material
LT-0970 1.07 © 2015 Digital Monitoring Products, Inc.
Specifications
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising