未命名 -1 - Xtrons
Car Multimedia System
DK Series User Manual
Professional vehicle entertainment multimedia
| Common Troubleshooting Guide |
Fault Reason Solution
Power fuse was burnt. Using the same Insurance
with main unit to replace
No bootup.
Other factors caused the
microprocessorincorrect
operation
After pressing the RESET key
with a small nib on the face
panel, power on again.
After ignition starting
up and power off, all
settings information
were missing.
The BATT of ACC ignition
positive power linemade
wrong connection.
Re-connect the shunting line
No remote control
action/function
Low battery in the remote
control
replace(change) the battery
of the remote control.
Poor receive stations
effect
Car antenna didn't go out
Poor antenna grounding.
Checking if the ANT of radio
automatic antenna control
lines are not connected well,
then, please re-check the
antenna and the ground wire
made correct connection all.
No way to put into
Optical disc
There has installed disks
already in the DVD loader
/mechanism.
Pop-up the disc in the unit
(device), then re-insert it
into again.
Disc can't play
Disc was scratched
Change the good disc
Optical disk's positive
and negative were
placed reversal(opposite)
Put the face of optical disk
logo upwards and put itinto
the device(unit).
The laser head has been
dirty
Using pick up head cleaning
disk to clear the pick up.
No action to switch
between Language
and sub-title
CD only burned a
language/ sub-title
No multilingual sub-title's disk.
Can't make switch between
language and sub-title
No image
No connect the video
cables very well from
main unit to TV.
Re-connect the connection
line.
Mode screen
dislocation
No making touch screen
calibration very well.
calibrating touch screen,press g
button for 5seconds to enter
into calibration interface
Functional disorders
Other factors caused the
microprocessorincorrect
operation
After pressing the resetting key
of "RESET" with a small nib on
the face panel(plate),to re-boot up.
| Bluetooth use method ] CODE : 0000
1,Enter into bluetooth interface,click" Q "icon to search nearby phones,
ensure bluetoot of your mobile phone is under searchable states when seraching.
Available bluetooth device will be displayed in the middle list,if too long,just click
и "Ny ” nu "
A .
2,Pair:find your phone in the list and click phone name to pair, also your mobile
phone will ask matching password,just input" 0000"and then click"sure" will be ok.
It will appear "LINK OK". If you want to cancel pairing,just find your phone in the
list and press your phone nmae for 3seconds,then your phone name will disappear
from the list. If you just cancel pairing on the phone but not on the car DVD player,
it will send a pairing request for every 30seconds to you mobile phone and cause
troubles to you.
3,Synchronous phonebook:" La] "or" "icon,a small window appears,
justclick ” IM “ and then pop up a phonebook synchronization request on
your phone, click"OK" to complete synchronization. Phonebook synchronization
finished,input first letter of contact on the keypad of screen to search(Chinese
search is the first letter of Pinyin).
4,Dial phone:click enter into dialing interface, input phone number on the
numeric keypad to call or hang up.
5,Bluetooth music:click" "enter into bluetooth music interface.Pls note
that open the player on the phone first when playing music,because the car DVD
player cannt start phone player.Some mobile phones may installed more than one
player,just start any one will be ok.
(#) Bluetooth phone 14:04 PM 25 $)
CJT lr 13731766558
3 *
6 | 0/+
| SWC settings |
Click“ ” icon on the main Ul to enter into the setup interface
1. Click the steering wheel to set the steering wheel
2. Click the“ "ico to set clear
3. Press the button on the steering wheel,and meanwhile press the function
which need to be set on the display,when the icon is in selected state,that’s
means ok
4. Repeat the steps for other buttons
5. Press”OK” to confirm once finished
6. Any mistake or resetting,just repeat 2-5
Note:make sure”button wire”on the steering wheel connected well with"SWC”on the unit,
as shown below:2 CSW wire connected with anode of steering wheel button wire,
GND conneted with cathode
14:04 PM 25 (9
steerng wheel digita
SRC - | 42 | Dl
| Map installation and parameter
Installing method :
1, insert SD card with map into the GPS slot on the panel of device
2, enterinto setup interface,click GPS icon and then turn to settings of
navigation path,the system will automatically find out all the “exe”
files in the map card,and then select correct navigation path,(as shown
below)press GPS on the panel or back to main Ul and click GPS icon will
start navigating.
Parameter : Operation System : WIN CE 6.0 Core Chinese/English version
Chipset : MSR2112
Resolution : 800X480
GPS BAUD(Baud rate ) : 9600bps
GPS COM : 2
® CL)
Current navigation path:
Current navigation path:
\StorageCard\printscreen exe
\StorageCard\NaviOne\NaviOne.exe A
| Easy Connected verified mobile phone list |
CARBIT
Date 2015/2/28 | Version V2.0 Date 2015/2/28 | Version V2.0
New models (OS Total Brands:17 |New models (0S Total Brands:17
Ver.) Models : 90| Ver, Models : 90
No.[Brand| Type [OS Ver en | No.|Brand| Type — [OSVer| Cum
1 | LG [Nexus5 2.9.2 |FOR WINCE | 31 ¡Samsung! SM-A5000 | 4.4.4 | FOR WINCE
2|LG |LG-P8810 4.0.3 |FOR WINCE | 32 |samsung] SM-N910X | 4.4.3 [FOR WINCE
3 | ZTE |ZTE U9180 | 4.3 [FOR WINCE | 33 [samsung SM-N7508V | 4.3 | FOR WINCE
4 | HTC |M85w 4.1.1 |FOR WINCE | 34 |Samsung|SM-N9002 | 4.4.2 [FOR WINCE
5 | HTC |D516D 4.3 ¡FOR WINCE | 35 |Samsung|SM-N9008S | 4.3 |FOR WINCE
6 [HuaweilU9508 4.1.2 | FOR WINCE | 36 |Samsung|SM-G8508S | 4.4.4 [FOR WINCE
7 |Huawei|C199 4.4.2 |FOR WINCE | 37 |Samsung|SM-G3509 | 4.1 FOR WINCE
8 |Huawei|C8816 4.3 |FOR WINCE | 38 [samsung|SM-G7106 | 4.3 |FOR WINCE
9 |Huawei|HONOR H30-L01 4.4.2 | FOR WINCE | 39 |Samsung! SM-G3819D | 4.1 FOR WINCE
10 Huawei|P6-C00 4.2.2 | FOR WINCE | 40 [Samsung SM-G9008V | 4.4.2 | FOR WINCE
11 Huawei[A1 99 4.1.2 |FOR WINCE | 41 |samsung| SM-T321 4.4.2 |FOR WINCE
12 |Huawei|HO1-TOO 4.4.2 | FOR WINCE | 42 |samsung|SM-G3818 | 4.2.2 | FOR WINCE
13 [Huawei|G620S-UL00| 4.4.4 | FOR WINCE | 43 |samsung|SM-G9006V | 4.4.2 | FOR WINCE
14 |Huawei|G7-UL20 4.4.4 | FOR WINCE | 44 |samsung| SM-G5309W| 4.4 FOR WINCE
15 [Huawei|G6205-UL00| 4.4.4 | FOR WINCE | 45 |Samsung!SM-W2014 | 4.2 FOR WINCE
16 |Huawei|MT7-TL10 4.4.2 | РОВ WINCE | 46 |Samsung|SCH-N719 | 4.3 FOR WINCE
17 |Huawei|G620-L72 4.3 FOR WINCE | 47 [samsung| SCH-P709 | 4.2 FOR WINCE
18 |Huawei|PE-TLOOM 4.4.2 | FOR WINCE | 48 |Samsungl GT-193001 4.3 FOR WINCE
19 [Huawei|CHE2-ULOO | 4.4.2 | FOR WINCE | 49 |Samsung| GT-19500 4.4.2 | FOR WINCE
20 [Huawei|G750-T00 4.2.2 | FOR WINCE
21 | Google|Nexus4 4.4.4 |FOR WINCE
22 | Sony |LT29i 4.1.2 | FOR WINCE
23 | Sony |c6603 4.4.4 | FOR WINCE
24 | Lenovo | A916 4.4.4 | FOR WINCE
25 | Lenovo | A690e 4.4.4 |FOR WINCE
26 |Samsung| GT-S6818 4.1.2 |FOR WINCE
27 |Samsung| GT-N7102 4.3 FOR WINCE
28 |Samsung| GT-19100 4.1.2 | FOR WINCE
29 [samsung| SM-19508 4.2.2 | FOR WINCE
30 |Samsung| SM-A3000 | 4.4 FOR WINCE
| DVD software upgrade instructions
Copy DVD softerware(total 2 files) as below into empty SD card;insert SD card into
GPS slot while off state of the device,and then it will upgrade automatically when detect
the software after power on.SD card can only be removed after upgrade completely
finished.Note:power off is prohibited while upgrading
DYDECOT. bin i pedvdrom. bin
BIN {4 BIN Y
KB ofl KB
ART UPDATE LOGO.
IF "ВЫ В в) LOGO FILE
START UPDATE MCU..
TART UPOATE 01/0.
! 1 = .
MUNBER NT
CFG SORAN. . . SUCCEED ©
UPDATE uD” e
| Mirror Link Instruction
After mobile phone bluetooth linked successfully with unit,connect this unit with
mobile phone with a 2.0 USB cable, it will prompt download mirror link “phonelink”
APP for the first time,and then prompt installation after finished(some mobile phones
may will not prompt download and install APP).APP installation finished, find the
developer option on the mobile phone,and then open “USB debug” ,the mobile
phone will connect with the unit automatically(some cellphones can only access
connection by clicking USB2 icon manually),
you will be able to operate any applications MS
of the mobile phone on this unit after 11:06
connected successfully;please repeat above
steps for failure.Checking whether the
mobile phone has installed APP,you can see
whether there is “phonelink” icon on the
phone UI
| MCU Software upgrade Instructions |
Copy MCU software(total 2 files) as below into empty SD card;insert SD card into |
GPS slot while off state of the device,and then it will upgrade automatically when detect
the software after power on.SD card can only be removed after upgrade completely
finished.Note:power off is prohibited while upgrading
Y STMEUD. BIN | Ny STM&_FROJECT
START oh LO
(a анИа BIN Yi
START, cov. 519
e me 160 KE 519 X
MCU CHECICSUN 06
Lp A
ay a ón
La" HEU de Fogo Жо THE D CARD
n LME
| ARM Software upgrade Instructions |
Copy ARM softwarde(total 8 files) as below into empty SD card;insert SD card into
GPS slot while off state of the device,and then it will upgrade automatically when detect
the software after power on.SD card can only be removed after upgrade completely
finished.Note:power off is prohibited while upgrading
— DYDBOOT. bin | ЕВООТ ay
[ Dat ahbor Lo BIN Ti HBO TT
J Te E 9 1
512 KB
FytAppUpdate bin FITCFG. BIN FytIng. bin
peg) | IN STA (220) | EN TA BIN Tf
a
CIL
| The notes about the full unit's connection diagram |
+ The product is used for such cars with 12V battery and negative grounding,
before installing this product on these cars with 24V batteries,such as truck, bus,
big coach etc.cars), please install the reduction voltage equipment firstly.
+ To avoid short circuit of the electrical system, please firstly switch off the
negative electrode terminal's wire of the batter before installing it.
* Please arrange the wiring in some place where can be fixed, thus, keep it no way
to touch any moving parts, such as the handbrake ,gear lever, etc ; Do not arrange
the wiring in the heat source area, such as near the heater discharge outlet,
otherwise, the heat source will cause the wiring insulation layer was melted or
worn,thus,it will cause short-circuit between the wiring and the car body.
* When replacing the blown fuse ,you must use (10A) fuse as ruled. If use high -
capacity rated fuses to replace ruled fuses, or no use fuses to direct connect,
very easy to cause a fire ordamage the device.
+ Do not let the yellow power cord go through the engine mounting hole and
introduced with warehouse positions to connect the battery, otherwise, it may
damage the power line, then, it will cause short circuit between power line and
car body.
+ Do not connect this product's power line with other devices's power lines,
otherwise, it will cause overloading to change overheating.
+ Please use insulation paste to wrap the leading wire of unused speaker, so as to
avoid(prevent) short circuit,please ensure that the leading wire of unused
speaker gets insulation, otherwise it will cause a short circuit.
+ Please ensure that keep any exposed wires to get insulation,meanwhile,bundling
all electric wires very well, avoiding any connection terminals to touch the
metal parts of this device's body,thus, it can prevent short sircuits.
+ If your car's ignition does not have ACC position, please use ignition switch key
to connect ignition wire/lead onto this on/off power source.
+ When turning on the power source, external power amplifier control signal
leads AMP. CONT outputlf this device(unit) connected an external amplifier,
please do not connect AMP. CONT leading wire to the end of power amplifier,
otherwise, it will cause electric leakage and fault.
+ For this product, forbidden its loudspeaker output terminals to connect ground
wire,otherwise it will burn out the amplifier. Do not use such loudspeaker system
with the common ground wire and three kinds of wires styles,no permitting to
connect the loudspeaker to car body.
¢ The loudspeaker which connects this device(unit) must be high-power type, the
minimum rated value is 50W, impedance values(resistance value) is 4Q, please
don't directly connected a severalof speaker leads orimpedance values
(resistance value) outside of this range, otherwise, it will cause short circuit and
damage the loudspeakers.
| Functions and features |
System Features
* MSTAR2531chipset solution , ARM Cortex-A7 core , 800MHz main frequency,
+ RAM 256MB,DDR3 @ 1600MHz
* Flash support SLC/MLC , 128 MB SLC NAND FLASH
Supported media formats for DISC
+ Compatible with DVD-R, DVD-RW, DVD +R, DVD + RW, CD-R,CD-RW CD-DA, MP3,
WMA, SVCD, VCD and MPEG1, MPEG2,MPEG4, JPEG format discs .
Supported media formats for USB/SD
+Compatible with MP3, WMA, WAV,AST, AVI, MP4,MPEG1,MPEG2,MPEG4,JPEG,
FLAC,RMVB format.
* Supports SD port and USB(2.0) port.
Radio functions
+ 30 storage radio stations (FM x 18pcs, AM12 xpcs).
+ Automatic, semi-automatic and manual search, preset memory radio stations.
TV functions(optional)
* Analog TV(ATV) * Digital TV(DTV)
Aux input,output,amplifier and other functions
*AUX input *1 * rear-view camera input * 1
*two-channes' amplifier output,which can be directly speaker.
+ 2 +1 channel audio output.
+ 4 channels amplifier output.
p——
Warning |
1.Do not expose the unit in the damp environment to prevent from fire or electric
shock accident.
2.Any change or modification to this unit without the clear priorconsent of the
authorization party may bring inconvenience to the users.
3.This unit is made up of high-precision accessories,do not dismantle the device
or adjust any accessories inside this device ifwithout authorization.
4.Do not touch the display screen with hard objects, so as to avoid scratching the
screen.
5.Please don't install this device in these placeswhich is in the way of driver's view
or effect driving.
6.To avoid any traffic accidents as driver's distraction,please don't operate this
device when driving, if needing to operate, please park the car in a safety
place first.
7.This device is fit for such cars with 12V power supply battery system of cathode
ground wire,please do not install this device to 24V battery's trucks or buses.
| Thank patronage!
Thank you very much for purchasing and using our digital car audio-visual
series products! To ensure you can use this product correctly,please read this
user manual carefully before use it and keep it well for your future reference.
| Safety Warning |
® Laws of some countries prohibit users from watching TV or otherprograms and
performing related operations when driving.For your personal safety,please do
not watch videos, TV and other related operations while driving.
® The system is only for assistant function when reversing(backing) ,we accept no
any responsibility for any accidents caused during reversing(backing).
Class 1 Laser Products
We have the rights not to inform in advacne if the product descriptions in this
manual have any changing.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising