Owner`s Manual - Fireplaces Plus

Owner`s Manual - Fireplaces Plus
Owner’s Manual
Installation and Operation
Models:
SL-750TRS-IPI-E
SL-550TRS-IPI-E
SL-750TRS-E
SL-550TRS-E
SL-350TRS-IPI
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
• Leave this manual with
party responsible for use
and operation.
D
DI O N
SC OT
AR
D
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
1
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
Congratulations
Congratulations on selecting a Heat & Glo gas appliance
—an elegant and clean alternative to wood burning
appliances. The Heat & Glo gas appliance you have
selected is designed to provide the utmost in safety,
reliability, and efficiency.
This Owner’s Manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
The information contained in this Owner’s Manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a new appliance, you’ll want to read and
carefully follow all of the instructions contained in this
Owner’s Manual. Pay special attention to all Cautions and
Warnings.
Your new Heat & Glo gas appliance will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of appliance products!
We recommend that you record the following pertinent
information about your appliance.
Homeowner Reference Information
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number:__________________________________________ Location on appliance: ____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
The model information regarding your specific appliance can be found on
the rating plate usually located in the control area of the appliance.
This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States)
4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495,
5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195,
6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2,
6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou
autres brevets americains et etrangers en attente).
Heat & Glo, a brand of Hearth & Home Technologies, Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
Type of Gas
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz):
NATURAL GAS
Gas and Electric
Information
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
ANSI Z21XX-XXXX · CSA 2.XX-MXX · UL307B
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
(Po. Col. d’eau)
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
Model Number
Serial Number
Table of Contents
1 Listing and Code Approvals
A.
B.
C.
D.
E.
F.
G.
H.
Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glass Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Combustible Materials Specification. . . . . . . . . . . . . .
Combustible Materials Specification . . . . . . . . . . . . . . . . .
Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for the Commonwealth of Massachusetts . .
4
4
4
4
5
5
5
6
J.
K.
L.
M.
Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . .
Install Decorative Wall Components (SLP only) . . . . . . . .
Heat Shield Requirements for Horizontal Termination . . .
Install Horizontal Termination Cap . . . . . . . . . . . . . . . . . .
9 Gas Information
A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2 Getting Started
10 Electrical Information
A. Design and Installation Considerations . . . . . . . . . . . . . . . 7
B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 7
C. Inspect Appliance and Components . . . . . . . . . . . . . . . . . . 7
A.
B.
C.
D.
E.
F.
3 Framing and Clearances
A.
B.
C.
D.
E.
Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 8
Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . . 9
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Elevated Hearth Systems . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4 Termination Locations
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 12
5 Vent Information and Diagrams
A.
B.
C.
D.
E.
Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Flex Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
14
15
16
6 Vent Clearances and Framing
A.
B.
C.
D.
Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . .
Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . .
Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . .
Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . .
26
27
28
29
7 Appliance Preparation
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 32
Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . .
Intellifire Ignition System Wiring . . . . . . . . . . . . . . . . . . . .
Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . .
Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Switch Installation for Fan (Optional) . . . . . . . . . . . .
43
43
44
44
46
46
11 Finishing
A.
B.
C.
D.
Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
48
49
51
12 Appliance Setup
A.
B.
C.
D.
E.
F.
G.
H.
I.
Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . .
Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lava Rock, Mineral Wool/Ember Placement . . . . . . . . . .
Install Refractory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grilles and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52
52
52
52
53
54
60
60
60
13 Operating Instructions
A.
B.
C.
D.
Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . .
Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . .
After Appliance is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . .
61
62
64
64
14 Troubleshooting
A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 65
B. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 67
8 Installing Vent Pipe (DVP and SLP Pipe)
A.
B.
C.
D.
E.
F.
G.
H.
I.
39
39
39
40
Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . .
Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . .
Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . .
Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . .
Install Decorative Ceiling Components (SLP only). . . . . .
Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . .
Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . .
Install RF4-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
34
34
35
35
36
37
37
38
15 Maintaining and Servicing Appliance
A. Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
16 Reference Materials
A.
B.
C.
C.
E.
Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . .
Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . .
Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
72
80
88
90
= Contains updated information.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
3
1
Listing and Code Approvals
A. Appliance Certification
MODELS: SL-750TRS-IPI-E, SL-550TRS-IPI-E,
SL-350TRS-IPI, SL-550TRS-E, SL-750TRS-E
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.88a-2007 • CSA 2.33a-2007
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
C. BTU Specifications
Models
U.S. (0-2000 ft.) or
Canada (2000-4500 ft.)
U.S.
SL-750TRS-IPI-E (NG)
SL-750TRS-E (NG)
Canada
U.S.
SL-750TRS-IPI-E (LP)
SL-750TRS-E (LP)
Canada
U.S.
SL-550TRS-IPI-E (NG)
SL-550TRS-E (NG)
Canada
U.S.
SL-550TRS-IPI-E (LP)
SL-550TRS-E (LP)
Canada
U.S.
SL-350TRS-IPI (NG)
Canada
U.S.
SL-350TRS-IPI (LP)
Canada
Maximum
Input
BTU/h
30,800
27,720
30,700
27,630
27,300
24,570
25,100
22,590
20,500
18,450
20,000
18,000
Minimum
Input
BTU/h
20,200
18,180
23.300
20,970
18,200
16,380
18,300
16,470
14,400
12,960
14,900
13,410
Orifice
Size
(DMS)
#37
#38
#52
#53
#40
#41
#53
#54
#44
#45
#55
#56
B. Glass Specifications
D. High Altitude Installations
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered
glass has been tested and certified to the requirements
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing
Certification Council SGCC# 1595 and 1597. Architectural Testing, Inc. Reports 02-31919.01 and 02-31917.01).
This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in
the U.S.A. and Canada.
Note: This installation must conform with local codes. In the
absence of local codes you must comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and
the CAN/CGA B149 Installation Codes in Canada.
4
When installing this appliance at an elevation above 2000
feet, it may be necessary to decrease the input rating
by changing the existing burner orifice to a smaller size.
Input rate should be reduced by 4% for each 1000 feet
above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the
heating value of the gas has been reduced, these rules
do not apply. To identify the proper orifice size, check with
the local gas utility.
If installing this appliance at an elevation above 4500 feet
(in Canada), check with local authorities.
WARNING
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof. Materials that are reported as passing ASTM E 136, Standard
Test Method for Behavior of Materials in a Vertical
Tube Furnace at 750ºC, shall be considered non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed
paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or whether
plastered or unplastered shall be considered combustible
materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
5
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, including but not limited to decks and porches, the following
requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) inch in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current
edition of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in
whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.
6
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
2
Getting Started
A. Design and Installation Considerations
C. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside. No additional outside air source is required.
WARNING
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
• Electrical wiring.
• Framing and finishing details.
• Carefully remove the appliance and components from
the packaging.
• The vent system components and trim doors are shipped
in separate packages.
• The gas logs may be packaged separately and must be
field installed.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
WARNING
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:
WARNING
Keep appliance dry.
• Mold or rust may cause odors.
• Water may damage controls.
B. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
Reciprocating saw
Framing material
Pliers
Hi temp caulking material
Hammer
Gloves
Phillips screwdriver
Framing square
Flat blade screwdriver
Electric drill and bits (1/4 in.)
Plumb line
Safety glasses
Level
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
Manometer
Voltmeter
Tape measure
Noncorrosive leak check solution
One 1/4 inch female connection (for optional fan).
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
7
3
Framing and Clearances
WARNING
Note:
• Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
Fire Risk
Provide adequate clearance:
• Around air openings
• To combustibles
• For service access
Locate appliance away from traffic areas.
A. Selecting Appliance Location
When selecting a location for your appliance it is important to
consider the required clearances to walls (see Figure 3.1).
NOTE: For actual appliance dimensions refer to Section 16.
A
N
E
L
F
D
F
A
A
C
C
In addition to these framing dimensions, also reference the following sections:
• Clearances and Mantel Projections (Section 3.C and 3.D)
• Vent Clearances and Framing (Section 6).
K
H
B
J
G
I
G
J
M
Models
SL-750TRS-IPI-E
SL-750TRS-E
SL-550TRS-IPI-E
SL-550TRS-E
A
B
C
in.
45-1/2
42
64-3/8
mm
1155
1067
1635
in.
42
37
59-1/2
mm
1067
940
1511
in.
39-1/2
34
55-7/8
mm
1003
864
1413
D
See Section
E for Alcove
Installation
E
Min.
F
Min.
G
H
I
J
K
L
M
N
1
1/2
45-1/2
64-3/8
16-1/4
48-1/2
68-3/4
16-5/8
7-1/2
9
25
13
1155
1635
413
1232
1737
422
191
229
1
1/2
44
62-1/4
16-1/4
48-1/2
68-3/4
15-1/16
7-1/2
7-1/8
25
13
1117
1581
413
1232
1737
383
191
181
1
1/2
44
62-1/4
16-1/4
48-1/2
68-3/4
13-1/2
7-1/2
6
25
13
1117
1581
413
1232
1737
343
191
152
SL-350TRS-IPI
Figure 3.1 Appliance Locations
8
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
insulation. If the appliance is being installed on a cement
slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.
B. Constructing the Appliance Chase
A chase is a vertical boxlike structure built to enclose the
gas appliance and/or its vent system. Vertical vents that
run on the outside of a building may be, but are not required to be, installed inside a chase.
C. Clearances
Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST
be checked.
WARNING
Fire Risk.
Odor Risk.
• Install appliance on hard metal or wood surfaces
extending full width and depth of appliance.
• Do NOT install appliance directly on carpeting,
vinyl, tile or any combustible material other than
wood.
Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building
envelope in any manner.
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
WARNING
Fire Risk.
• Construct chase to all clearance specifications
in manual.
• Locate and install appliance to all clearance
specifications in manual.
To further prevent drafts, the wall shield and ceiling
firestops should be caulked with high temperature caulk
to seal gaps. Gas line holes and other openings should
be caulked with high temp caulk or stuffed with unfaced
A
MEASURE FROM
TOP OF UNIT OPENING
OR FROM TOP OF HOOD
E
F
H
B
G
J
C
I
D
A
Models
Inches
SL-750TRS-IPI-E
SL-750TRS-E
Millimeters
Inches
SL-550TRS-IPI-E
SL-550TRS-E
Millimeters
B
DVP PIPE
SLP PIPE
Rough
Opening
(Width)
Rough
Opening
(Width)
10
8-5/8
Rough
Opening
(Height)
38-1/4
C
D
E
Rough
Opening
(Width)
Clearance
to Ceiling
F
G
*DVP PIPE
SLP PIPE
Rough
Opening
(Depth)
Rough
Opening
(Depth)
28-1/4
16-1/4
42
32
0
0
H
I
J
Combustible Combustible
Behind
Sides of
Front of
Floor
Flooring
Appliance Appliance Appliance
1/2
1/2
36
254
219
971
699
413
1067
813
0
0
13
13
915
10
8-5/8
34-3/4
28-1/4
16-1/4
37
32
0
0
1/2
1/2
36
940
813
0
0
13
13
915
254
219
882
699
413
Inches
10
8-5/8
32-3/4
28-1/4
16-1/4
34
32
0
0
1/2
1/2
36
Millimeters
254
219
832
699
413
864
813
0
0
13
13
915
SL-350TRS-IPI
* Dimension when rear venting with one 90º elbow
Figure 3.2 Clearances to Combustibles (Vertical Venting)
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
9
D. Elevated Hearth Systems
Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various dimensions.
Some hearth systems will elevate the appliance off the floor at a given dimension. For example, if appliance will be used with a
Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 inches. The 9-1/4 inch elevation will also have to be added to the
following: Extension Wall Hole referenced in Figure 6.3 (Exterior Wall Hole) and Rough Opening Height (header height) referenced in
Figure 3.2. NOTE: Finished floor thickness should also be considered when determining installation dimensions.
MODEL
SL-350
SL-550
SL-750
ELEVATED APPLIANCE
DIMENSION
See Note 1
0
9 1/4 in.
0
9 1/4 in.
0
9-1/4 in.
0
9-1/4 in.
0 (See Note 3)
9 1/4 in.
1-1/2 in.
0
1-3/4 in.
0
MARBLE LEG CUT
LENGTH
See Note 2
27 3/8 in.
27 3/8 in.
27 3/8 in.
27 3/8 in.
29-3/8 in.
29-3/8 in.
29-3/8 in.
29-3/8 in.
27-3/8 in.
29-3/8 in.
N/A
N/A
N/A
N/A
CAMM550PGH
1-3/4 in.
N/A
ESSEX550PG
ESSEX550PGH
ESSEXM550PG
0
1-3/4 in.
0
N/A
N/A
N/A
ESSEXM550PGH
1-3/4 in.
N/A
LUNA-32-GY
MON550PG
MON550PGH
MONM550PG
1-1/16 in.
0
1-3/4 in.
0
N/A
N/A
N/A
N/A
MONM550PGH
1-3/4 in.
N/A
0
9-1/4 in.
0
9-1/4 in.
0 (See Note 3)
9-1/4 in.
1-1/2 in.
0
1-3/4 in.
0
32-7/8 in.
32-7/8 in.
32-7/8 in.
32-7/8 in.
27-3/8 in.
29-3/8 in.
N/A
N/A
N/A
N/A
CAMM36PGH
1-3/4 in.
N/A
ESSEX36PG
ESSEX36PGH
ESSEXM36PG
0
1-3/4 in.
0
N/A
N/A
N/A
ESSEXM36PGH
1-3/4 in.
N/A
LUNA-36-GY
MON36PG
MON36PGH
MONM36PG
1-1/16 in.
0
1-3/4 in.
0
N/A
N/A
N/A
N/A
MONM36PGH
1-3/4 in.
N/A
DESCRIPTION
PART #
KENWOOD CABINET
KENWOOD CABINET W/ BASE
KENWOOD CORNER CABINET
KENWOOD CORNER CABINET W/ BASE
KENWOOD CABINET
KENWOOD CABINET W/ BASE
KENWOOD CORNER CABINET
KENWOOD CORNER CABINET W/ BASE
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
LAURENT SURROUND
CAMDEN SURROUND
CAMDEN SURROUND W/HEARTH
CAMDEN SURROUND W/MANTEL
CAMDEN SURROUND W/MANTEL &
HEARTH
ESSEX SURROUND
ESSEX SURROUND W/HEARTH
ESSEX SURROUND W/MANTEL
ESSEX SURROUND W/MANTEL &
HEARTH
LUNA SURROUND
MONROE SURROUND
MONROE SURROUND W/HEARTH
MONROE SURROUND W/MANTEL
MONROE SURROUND W/MANTEL &
HEARTH
KENWOOD CABINET
KENWOOD CABINET W/ BASE
KENWOOD CORNER CABINET
KENWOOD CORNER CABINET W/ BASE
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
LAURENT SURROUND
CAMDEN SURROUND
CAMDEN SURROUND W/HEARTH
CAMDEN SURROUND W/MANTEL
CAMDEN SURROUND W/MANTEL &
HEARTH
ESSEX SURROUND
ESSEX SURROUND W/HEARTH
ESSEX SURROUND W/MANTEL
ESSEX SURROUND W/MANTEL &
HEARTH
LUNA SURROUND
MONROE SURROUND
MONROE SURROUND W/HEARTH
MONROE SURROUND W/MANTEL
MONROE SURROUND W/MANTEL &
HEARTH
KDC44SBP
KDC44SBP W/ HTKDC44SBP
KDA44SBP
KDA44SBP W/ HTKDA44SBP
KDC44SBP
KDC44SBP W/ HTKDC44SBP
KDA44SBP
KDA44SBP W/ HTKDA44SBP
AFKDMPA
AFKDMPA W/ HTKDMPA
LAURENT-32
CAM550PG
CAM550PGH
CAMM550PG
KDC48DBP
KDC48DBP W/ HTKDC48DBP
KDA48SBP
KDA48SBP W/ HTKDA48SBP
AFKDMPB
AFKDMPB W/ HTKDMPB
LAURENT-36
CAM36PG
CAM36PGH
CAMM36PG
NOTE 1. Add dimensions to Exterior Wall Hole (Figure 6.2) and Rough Opening Height (Figure 3.2).
NOTE 2. Verify Marble Cut Lengths on site prior to cutting.
NOTE 3. Dimensions assume use of a 3/4 in. Hearth Pad.
10
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
E. Mantel Projections
All measurements are in inches.
CEILING
1/2 IN.
MINIMUM
12
11
10
9
8
32
7
2-7/8 IN.
MINIMUM
3 FT. MAXIMUM
6
5
4
3
4
5
6
7
9
8
10
11
12
13
Note: Clearance from opening
to perpendicular wall.
Figure 3.5 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
TOP OF HOOD OR FIREPLACE OPENING
Figure 3.3 Clearances to mantels or other combustibles
above appliance
1/2 in.
SHEETROCK
3-1/2 in.
3 IN.
MINIMUM
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
5-3/8 IN.
MINIMUM
1/2 in.
UNLIMITED
Note: Clearance from opening
to perpendicular wall.
Figure 3.6 Wall Projection (Acceptable on one side of opening.)
NON-COMBUSTIBLE ZONE
Figure 3.4 Non-Combustible Zone
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
11
4
Termination Locations
A. Vent Termination Minimum Clearances
HORIZONTAL
OVERHANG
2 FT.
MIN.
WARNING
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Fire Risk.
Explosion Risk.
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
• Combustible materials blocking cap may
ignite.
• Restricted air flow affects burner operation.
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
WARNING
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as
specified.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
* 3 foot minimum in snow regions
Measure vertical clearances from this surface.
Figure 4.2 Minimum height from roof to lowest discharge
opening
Figure 4.2 specifies minimum vent heights for various
pitched roofs.
GAS, WOOD OR FUEL
OIL TERMINATION
C
B
GAS
TERMINATION
A
Measure horizontal clearances from this surface.
(See Figure 4.4 for specific clearances)
Figure 4.1
Gas
Termination
Wood & Fuel Oil
Termination
Comments
A
6 in.
20 in. min.
Horizontal distance between terminations
B
20 in.
24 in. min.
Distance to perpendicular wall
C
18 in.
18 in.
Vertical distance between terminations
Figure 4.3 Multiple Vertical Termination
12
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
M
N
P
R
Q
(See Note 2)
V
T
V
S
Electrical
Service
S
V
D*
V
V = VENT TERMINAL
A
B
D*
X = AIR SUPPLY INLET
= 12 inches.................clearances above grade, veranda,
(See Note 1)
porch, deck or balcony
= 12 inches.................clearances to window or door
that may be opened, or to permanently closed window. (Glass)
= 18 inches.................vertical clearance to unventilated
soffit or to ventilated soffit located
above the terminal
*30 inches................for vinyl clad soffits and below
electrical service
F
= 9 inches..................clearance to outside corner
G
= 6 inches...................clearance to inside corner
H
= 3 ft. (Canada) ..........not to be installed above a gas
meter/regulator assembly within 3
feet (90 cm) horizontally from the
center-line of the regulator
= 3 ft ...........................clearance to gas service regulator
vent outlet
= 9 inches (U.S.A.)
12 inches (Canada) clearance to non-mechanical
air supply inlet to building or the
combustion air inlet to any other
appliance
= 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (powered) air supply inlet
I
J
K
** a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings.
*** only permitted if veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the floor, or meets Note 2.
NOTE 1: On private property where termination is less than 7 feet above
a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap
shield is suggested. (See vents components page)
NOTE 2: Termination in an alcove space (spaces open only on one side
and with an overhang) are permitted with the dimensions specified for
vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be a
minimum of 1 foot below the termination cap.
Figure 4.4 Minimum Clearances for Termination
= AREA WHERE TERMINAL IS NOT PERMITTED
L** = 7 ft. ......................... c l e a r a n c e a b o v e p a v e d
(See Note 1)
sidewalk or a paved driveway
located on public property
M*** = 18 inches................ clearance under veranda, porch,
deck, balcony or overhang
42 inches ............... vinyl
S
= 6 inches.................clearance from sides of electri(See Note 5)
cal service
T
= 12 inches................clearance above electrical
(See Note 5)
service
Alcove Applications
N
= 6 inches ..................non-vinyl sidewalls
12 inches ................vinyl sidewalls
P
= 8 ft.
QMIN
RMAX
1 cap
3 feet
2 x Q ACTUAL
2 caps
6 feet
1 x Q ACTUAL
3 caps
9 feet
2/3 x Q ACTUAL
4 caps
12 feet
1/2 x Q ACTUAL
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
NOTE 3: Local codes or regulations may require different
clearances.
NOTE 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
NOTE 5: Location of the vent termination must not interfere with
access to the electrical service.
WARNING: In the U.S: Vent system termination is NOT permitted in
screened porches. You must follow side wall, overhang and ground
clearances as stated in the instructions.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas with
two or more sides open. You must follow all side walls, overhang
and ground clearances as stated in the instructions.
Heat & Glo assumes no responsibility for the improper performance
of the appliance when the venting system does not meet these
requirements.
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
13
5
Vent Information and Diagrams
A. Vent Table Key
The abbreviations listed in this vent table key are used in
the vent diagrams.
Description
V2
Second section of vertical length
H1
First section (closest to appliance) of horizontal length
H2
Second section of horizontal length
Vertical
8-1/2 in.
First section (closest to appliance) of vertical length
12
V1
in
.
Symbol
8-1/2 in.
WARNING
Fire Hazard.
Explosion Risk.
Asphyxiation Risk.
Do NOT connect this gas appliance to a chimney
flue serving a separate solid-fuel or gas burning
appliance.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
May impair safe operation of this appliance or
other appliances connected to the flue.
Horizontal
Figure 5.1
C. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
1. Pipe measurements are shown using the effective length
of pipe (see Figure 5.2).
B. Use of Elbows
CAUTION
ALL vent configuration specifications MUST be followed.
• This product is tested and listed to these specifications.
• Appliance performance will suffer if specifications are not
followed.
Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 5.1).
Two 45º elbows may be used in place of one 90º elbow. On
45º runs, one foot of diagonal is equal to 8-1/2 inches horizontal run and 8-1/2 inches vertical run. A length of straight
pipe is allowed between two 45º elbows (see Figure 5.1).
2. Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see
Figure 4.1).
3. Vertical terminations are measured to bottom of termination cap.
4. Horizontal pipe installed level with no rise.
Pipe
Effective
Height/Length
Inches
Millimeters
DVP4
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
DVP12MI 3 to 12
76 to 305
DVP24MI 3 to 24
76 to 610
Figure 5.2 DVP Pipe Effective Length
14
Effective Length
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
D. Use of Flex Vent
The flex vent must be supported with
the spacing between support intervals
not exceeding 4 feet, with no more
than ½ inch sag between supports.
A support is required at each change
in venting direction, and in any location
where it is necessary to maintain the
necessary clearance to combustibles.
A simple “up and out” installation (Figure 5.3) requires only enough support
to maintain the necessary clearance
to combustibles. However, the vent attachment point and the firestop location are considered to be supports.
3 in . C L E A R A N C E
T E R M IN AT IO N
CAP
F L E X -V E N T
1 in .
CLEAR AN CE
Figure 5.3
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
15
E. Vent Diagrams
WARNING
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling firestops.
• ALWAYS maintain specified clearances around venting and firestop systems.
• Install wall shield and ceiling firestops as specified.
Failure to keep insulation or other material away from vent pipe may cause fire.
1. Top Vent - Horizontal Termination Venting
One Elbow
H1 Maximum
V Minimum
SL-350TRS-IPI
90º Elbow
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
WARNING
SL-550, SL-750TRS-E
1-1/2 ft.
457 mm
1 ft.
305 mm
1/2 ft.
152 mm
2 ft.
610 mm
2 ft.
610 mm
1-1/2 ft.
457 mm
3 ft.
914 mm
3 ft.
914 mm
2-1/2 ft.
762 mm
5 ft.
1-1/2 m
5 ft.
1-1/2 m
3-1/2 ft.
1.1 m
7 ft.
2.1 m
7 ft.
2.1 m
4-1/2 ft.
1.4 m
15 ft.
4.6 m
15 ft.
4.6 m
H1 Maximum= 15 ft. (4.6 m)
V1 + H1 Maximum= 40 ft. (12.2 m)
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZCSS termination caps on top vented fireplaces,
a one foot minimum vertical vent section is
required before installing first elbow.
• When using DVP-TB1 termination cap on top vented
fireplaces, a three foot minimum vertical vent section is
required before installing first elbow.
V1
H1
Figure 5.4
16
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
Two Elbows
H Maximum
V Minimum
Note: Use SLP Series
components only.
SL-350TRS-IPI, SL-550TRS-E, SL-750TRS-E
90º Elbow
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
NOT ALLOWED
1/2 ft.
152 mm
1 ft.
305 mm
1-1/2 ft.
457 mm
2 ft.
610 mm
2-1/2 ft.
762 mm
4 ft.
1.2 m
3-1/2 ft.
1.1 m
6 ft
1.8 m
4-1/2 ft.
1.4 m
14 ft.
4.3 m
H1 + H2 Maximum= 14 ft. (4.3 m)
V1 + H1 + H2 Maximum= 40 ft. (12.2 m)
WARNING
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZCSS termination caps on top vented fireplaces,
a one foot minimum vertical vent section is
required before installing first elbow.
• When using DVP-TB1 termination cap on top vented
fireplaces, a three foot minimum vertical vent section is
required before installing first elbow.
V1
H2
H1
INSTALLED
HORIZONTALLY
Figure 5.5
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
17
1. Top Vent - Horizontal Termination - (continued)
Three Elbows
H1 Maximum
V1 Minimum
H1 + H2 Maximum
Model: SL-350TRS-IPI
Elbow only
H1 Maximum
H1 + H2 Maximum
Models: SL-550TRS-IPI-E, SL-750TRS-IPI-E
V2
V1 + V2 Minimum
*
*
1-1/2 ft.
457 mm
2 ft.
610 mm
1 ft.
305 mm
2 ft.
610 mm
*
*
4 ft.
1.2 m
2 ft.
610 mm
4 ft.
1.2 m
*
*
1/2 ft.
152 mm
2 ft.
610 mm
1-1/2 ft.
457 mm
3 ft.
914 mm
6 ft.
1.8 m
3 ft.
914 mm
6 ft.
1.8 m
*
*
2-1/2 ft.
762 mm
5 ft.
1.5 m
10 ft
3.0 m
5 ft.
1.5 m
10 ft.
3.0 m
*
*
3-1/2 ft.
1.1 m
7 ft.
2.1 m
14 ft.
4.3 m
7 ft.
2.1 m
14 ft.
4.3 m
*
*
4-1/2 ft.
1.4 m
14 ft.
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
*
*
V1 + H1 + V2 + H2 Maximum = 40 ft. (12.2 m)
*No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 CANNOT exceed 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
H2
V2
H1
WARNING
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZCSS termination caps on top vented fireplaces,
a one foot minimum vertical vent section is
required before installing first elbow.
Figure 5.6
18
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
V1
2. Top Vent - Vertical Termination
Exhaust restrictor Instructions
1. Install the exhaust restrictor over the center of the exhaust outlet in the firebox (see Figure 5.8).
No Elbow
2. Center the exhaust restrictor in the open end of the
exhaust outlet and secure through the slots on the exhaust restrictor with the 2-1/4 in. self tapping screws
provided in the appliance manual bag.
Note: Use SLP Series
components only.
Note: If installing a vertical vent/termination off the top of
the appliance, the optional vertical termination baffle may
be needed.
V1 = 60 ft. Max. (18.3 m)
INNER HEAT SHIELD
To access the
exhaust openings,
remove the inner
heat shield. To
remove inner heat
shield, remove the
two screws.
Top Vent Application
Exhaust restrictor
V1
Rear Vent Application
Exhaust restrictor
Note: Be sure to reinstall the inner heat
shield after exhaust
restrictor installation.
Figure 5.7
Exhaust restrictors are recommended for these vertically terminated products which have excessive draft.
Exhaust restrictors will compensate for high draft, and
restore visual flame height. If the vent configuration has
a total vertical of 15-60 feet, an exhaust restrictor may
be needed. The exhaust restrictor can be located in the
appliance manual bag.
Figure 5.8
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
19
2. Top Vent - Vertical Termination - (continued)
Two 90º Elbows
V1 Minimum
90º Elbow
H1 Maximum
H1 Maximum
V2
V1 + V2 Minimum
SL-350TRS-IPI
SL-550TRS-E, SL-750TRS-E
*
*
1-1/2 ft.
457 mm
1 ft.
305 mm
*
*
1/2 ft.
152 mm
2 ft.
610 mm
2 ft.
610 mm
*
*
1 ft.
305 mm
2-1/2 ft.
762 mm
2-1/2 ft.
762 mm
*
*
2 ft.
610 mm
4 ft.
1.2 m
4 ft.
1.2 m
*
*
3 ft.
914 m
6 ft.
1.8 m
6 ft.
1.8 m
*
*
4 ft.
1.2 m
8 ft.
2.4 m
8 ft.
2.4 m
*
*
5 ft.
1.5 m
15 ft.
4.6 m
15 ft
4.6 m
*
*
H1 Maximum= 15 ft. (4.6 m)
V1 + V2 + H Maximum = 40 ft. (12.2 m)
*No specific restrictions on this value EXCEPT V1 + V2 + H1 CANNOT exceed 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
V2
H1
V1
Figure 5.8
20
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
2. Top Vent - Vertical Termination - (continued)
Three 90º Elbows
ALL MODELS
H1+ H2 Maximum
V1
Note: Use SLP Series
components only.
90º Elbow
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
0
0
V2
V1 + V2 Minimum
1-1/2 ft. 457 mm 1-1/2 ft. 457 mm
1/2 ft..
152 mm
1 ft.
305 mm
*
*
*
*
1-1/2 ft.
457 mm
2 ft.
610 mm
*
*
*
*
2-1/2 ft.
762 mm
4 ft.
1.2 m
*
*
*
*
3-1/2 ft.
1.1 m
6 ft.
1.8 m
*
*
*
*
4-1/2 ft.
1.4 m
14 ft.
4.3 m
*
*
*
*
H1 Maximum = 14 ft. (4.3 m)
*No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2
CANNOT exceed 40 ft. (12.2 m).
V2
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 5.9
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
21
2. Top Vent - Vertical Termination - (continued)
V1 Min.
Four 90º Elbows
1-1/2 ft.
457 mm
H1 Max.
4 ft.
V2 Min.
1.2 m
4 ft.
1.2 m
H2 Max.
4 ft.
1.2 m
V1 + V2 + V3 + H1 + H2 Maximum= 40 ft. (12.2 m)
V3
V2
H2
Note: Use SLP Series
components only.
H1
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
V1
Figure 5.17
22
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
V3 Min.
3-1/2 ft.
1.0 m
3. Rear Vent - Horizontal Termination
No Elbow
Two 90º Elbows
Note: Use DVP Series
components only.
Note: Use DVP Series
components only.
H1 = 24 in. (610 mm) Maximum
90-DEGREE ELBOWS
H1
Use two 90º elbows for corner installations.
The use of two 90º elbows in a corner installation
will affect space requirements.
Figure 5.10
Figure 5.11
H1 Maximum
Two 90º Elbows
Note: Use DVP Series
components only.
V1 Minimum
H2
Back to Back
Elbows
1-1/2 ft.
457 mm
3-1/2 ft.
1.1 m
1 ft.
5-1/2 ft.
1.7 m
7-1/2 ft.
2.3 m
H1 + H2 Maximum
1 ft.
305 mm
2-1/2 ft.
762 mm
305 mm
3 ft.
914 mm
6-1/2 ft.
2.0 m
2 ft.
610 mm
5 ft.
1.5 m
10-1/2 ft.
3.2 m
3 ft.
914 mm
6-1/2 ft.
2.1 m
14 ft.
4.3 m
H1 Maximum = 7-1/2 ft. (2.3 m)
H1 + H2 Maximum = 14 ft. (4.3 m)
V1 + H1 + H2= 40 ft. (12.2 m)
H2
V1
H1
Figure 5.12
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
23
3. Rear Vent - Horizontal Termination - (continued)
Three Elbows
H1 Maximum
Note: Use DVP Series
components only.
V1 Minimum
Back to Back
Elbows
1-1/2 ft.
457 mm
3-1/2 ft.
1.1 m
1 ft.
5-1/2 ft.
1.7 m
2 ft.
7-1/2 ft.
2.3 m
3 ft.
H2+ H3
H1+ H2+ H3 Maximum
1 ft.
305 mm
2-1/2 ft.
762 mm
305 mm
2 ft.
610 mm
5-1/2 ft.
1.7 m
610 mm
4 ft.
1.2 m
9-1/2 ft.
2.9 m
1.8 m
13-1/2
ft.
4.1 m
914 mm
6 ft.
H1 Maximum = 7-1/2 ft. (2.3 m)
H1 + H2 + H3 Maximum =13-1/2 ft. (4.1 m)
V1 + H1 + H3= 40 ft. (12.2 m)
INSTALLED
HORIZONTALLY
H3
H2
V1
Figure 5.13
H1
4. Rear Vent - Vertical Termination
One Elbow
V1 Minimum
Elbow Only
Note: Use DVP Series
components only.
H1 Maximum
1-1/2 ft.
457 mm
1 ft.
305 mm
3-1/2 ft.
1.1 m
2 ft.
610 mm
5-1/2 ft.
1.7 m
3 ft.
914 mm
7-1/2 ft.
2.3 m
H1 Maximum = 7-1/2 ft. (2.3 m)
V1 + H1 Maximum = 40 ft. (12.2 m)
V1
H1
Figure 5.14
24
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
4. Rear Vent - Vertical Termination - (continued)
Two Elbows
H1+ H2 Maximum
Note: Use DVP Series
components only.
V1 Minimum
1/2 ft.
152 mm
Back to Back Elbows
2-1/2 ft.
762 mm
1 ft.
305 mm
4-1/2 ft.
1.4 m
2 ft.
610 mm
6-1/2 ft.
2.0 m
3 ft.
914 mm
H Maximum = 6-1/2 ft. (2 m)
V1 + H1 + H2 Maximum = 40 ft. (12.2 m)
V1
INSTALLED
HORIZONTALLY
H1
H2
Figure 5.15
H1 Maximum
Three Elbows
Note: Use DVP Series
components only.
V1 Minimum
H2
H1 + H2 Maximum
Back to Back
Elbows
1 ft.
305 mm
2-1/2 ft.
762 mm
1.1 m
1 ft.
305 mm
3 ft.
914 mm
6-1/2 ft.
2.0 m
5-1/2 ft.
1.2 m
2 ft.
610 mm
5 ft.
1.5 m
10-1/2 ft.
3.2 m
7-1/2 ft.
2.3 m
3 ft.
914 mm
7 ft.
2.1 m
14-1/2ft.
4.4 m
1-1/2 ft.
457 mm
3-1/2 ft.
H1 Maximum = 7-1/2 ft. (2.3 m)
V1 + V2 + H1 + H2 Maximum = 40 ft. (12.2 m)
V2
H2
V1
H1
Figure 5.16
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
25
6
Vent Clearances and Framing
A. Pipe Clearances to Combustibles
WARNING
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as
specified.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
• DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
• If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
• SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed.
If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.
(DVP-SLP Pipe Shown)
3 in. (76 mm)
top clearance
Heat
Shield
3 in. (76 mm)
top clearance *
Heat
Shield
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
WALL
3 in. (76 mm)
top clearance *
Heat
Shield
Heat
Shield
Wall
Shield
Firestop
1 in. (25 mm)
clearance
bottom & sides
WALL
* When using SLP pipe, minimum clearances from the vent pipe to combustible materials at wall shield firestops are:
Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
Figure 6.1 Horizontal Venting Clearances To Combustible
Materials
26
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
B. Wall Penetration Framing
Combustible Wall Penetration
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 1-1/2 in. (38 mm)
overlap of attached heat shields must be maintained.
• DVP pipe - A wall shield firestop is required on one side
only on interior walls. If your local inspector requires a
wall shield firestop on both sides, then both wall shield
firestops must have a heat shield (refer to Section 16.B.)
attached to them.
• See Section 8.M. for information for regarding the installation of a horizontal termination cap.
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter
one in. greater than the pipe is acceptable.
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
10 in.
10 in.
C
10 in.
A*
D
12 in.
B*
SL-750TRS-IPI-E
SL-750TRS-E
SL-550TRS-IPI-E
SL-550TRS-E
Inches
Millimeters
Inches
Millimeters
Inches
SL-350TRS-IPI
Millimeters
A*
B*
C
D
41
27-7/8
40
26-7/8
1041
708
1016
683
36-1/2 24-3/8 35-1/2 23-3/8
927
619
902
594
35-1/2 22-3/8 34-1/2 21-3/8
902
568
876
543
* Shows center of vent framing hole for top or rear venting. The
center of the hole is one (1) inch (25.4 mm) above the center of
the horizontal vent pipe.
Figure 6.2 Exterior Wall Hole
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
27
C. Vertical Penetration Framing
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/fl oor (see
Figure 6.3).
• SLP pipe only - Frame opening 9 in. x 9
in. (229 mm x 229 mm) whenever the vent
penetrates a ceiling/floor (see Figure 6.3).
ATTIC ABOVE
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 6.4.
A
• Secure with three fasteners on each side.
WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
A
PIPE
A
DVP
10 in. (254 mm)
SLP
9 in. (229 mm)
Figure 6.3
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE
CEILING FIRESTOP
INSTALLED BELOW CEILING
Figure 6.4 Installing the Attic Shield
28
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
CEILING FIRESTOP
INSTALLED ABOVE CEILING
D. Install Attic Insulation Shield
WARNING! Fire Risk. DO NOT allow loose materials or
insulation to touch vent. Hearth & Home Technologies
Inc. requires the use of an attic shield.
BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE
The National Fuel Gas Code ANSI Z223.1 and NFPA 54
requires an attic shield constructed of 26 gauge minimum
metal that extends at least 2 in. (51 mm) above insulation.
Attic shields must meet specified clearance and be secured in place.
Flat Ceiling Installation
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
INSERT 3
SCREWS
LASER-ETCHED
CUT LINES
BEND 3 TABS
OUTWARD TO
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
CLEARANCE
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
Figure 6.5 Attic Insulation Shield
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Vaulted Ceiling Installation
• The attic insulation shield has been laser-etched with cut
lines and ceiling pitches to make field trimming easier.
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Cut the attic insulation shield (if application is for vaulted
ceiling) using a laser-etched cut line, to fit your ceiling
pitch. Snip cut edge to recreate 1 in. bend tabs all the
way around the bottom.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90° to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90° around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
29
7
Appliance Preparation
WARNING
Fire Risk
Once appliance is setup for top or rear venting, it
CANNOT be changed at a later time.
If vent cap and components previously removed
are improperly reinstalled, a fire may result.
A. Top Vent
CAUTION
Sharp Edges
• Wear protective gloves and safety
glasses during installation.
2 SCREWS
Figure 7.3 Replace the two screws as shown.
Note: Actual unit may look different than the fireplace shown
in this section.
2 SCREWS
Figure 7.1 For top vent, remove the two screws holding the
top heat shield in place. For rear vent, see Section 7B.
WARNING
Figure 7.4 Remove the vent cap.
Fire Risk
Do not remove heat shield.
Elevated header temperatures may cause a fire.
Figure 7.2 Rotate the top heat shield to the vertical
position as shown above. The heat shield must remain in
the vertical position.
30
Figure 7.5 Remove the insulation basket and white insulation from the center vent pipe.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
Figure 7.9 Cut the metal retaining band and fold the
sides out.
Figure 7.6 Remove the insulation from the outer vent pipe.
Figure 7.10 Fold the center parts of the retaining band
out and use to remove the vent cap.
2 SCREWS
Figure 7.7 To attach the first section of vent pipe, make
sure to use the fiberglass gasket to seal between the first
vent component and the outer fireplace wrap. Use 2 self
tapping screws to secure the gasket to the outer wrap.
Note: Once the vent cap has been removed, it cannot be
reattached.
Figure 7.11 Discard the vent cap, remove and discard
the insulation basket. Note: Once the vent cap has been
removed it CANNOT be reattached.
B. Rear Vent
Figure 7.8 Fold the tabs toward the center of the fire plug
(90°) and remove the insulation gasket.
Figure 7.12 Attach the first vent section (it will snap into
place). Slide the insulation gasket onto the vent section,
up against the appliance and over the tabs. Use two selftapping screws to secure gasket to outer wrap.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
31
C. Securing and Leveling the Appliance
WARNING
Fire Risk.
• Prevent contact with sagging, loose insulation.
• Do NOT install against combustible materials
such as exposed insulation, plastic and insulation
backer.
The diagram shows how to properly position, level, and
secure the appliance (see Figure 7.13). Nailing tabs are provided to secure the appliance to the framing members.
• Venting - refer to Vent Clearances and Framing (Section
6) for hole location.
• Place the appliance into position.
• Level the appliance from side to side and front to back.
NAILING TABS
BOTH SIDES
• Shim the appliance as necessary. It is acceptable to use
wood shims.
• Bend out nailing tabs on each side.
• Keep nailing tabs flush with the framing.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
Figure 7.13 Proper positioning, leveling and securing of an
appliance
WARNING
Fire Risk.
• ALWAYS maintain specified
clearances around the appliance.
• Do NOT notch into the framing around the appliance spacers.
Failure to keep insulation, framing or other material away from
the appliance may cause fire.
32
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
8
Installing Vent Pipe (DVP and SLP Pipe)
A. Assemble Vent Sections (DVP Pipe Only)
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face
toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end to the starting collar
• Inner pipe over inner collar
• Push the pipe section until all lanced tabs snap in place
• Lightly tug on pipe to confirm it has locked.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
All outer pipe joints must be sealed with high temperature
silicone, including the slip section that connects directly to
the horizontal termination cap.
Figure 8.1 High Temperature Silicone Sealant
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 8.1
A
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Assemble Pipe Sections (DVP Pipe Only)
Per Figure 8.2:
Lances
B
Figure 8.3
Figure 8.2
Note: Make sure that the seams are not aligned to prevent
unintentional disconnection.
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
CORRECT
For 90° and 45° elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2 in.
(13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
Figure 8.4 Seams
INCORRECT
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
33
B. Assemble Vent Sections (SLP Pipe Only)
C. Assemble Slip Sections
To attach the first vent component to the starting collars
of the appliance:
• Slide the inner flue of the slip section into the inner flue
of the pipe section and the outer flue of the slip section
over the outer flue of the pipe section. See Figure 8.6.
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Slide together to the desired length.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 8.5.
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration.
High temperature caulk may be used to hold the part in
place.
• Continue adding vent components, locking each
succeeding component into place.
Pilot hole
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
Figure 8.6 Slip Section Pilot Holes
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with high temperature silicone,
including the slip section that connects directly to the horizontal termination cap.
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 8.7.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 8.1
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Figure 8.7 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
Figure 8.5 Adding Venting Components
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed using
a high temperature silicone sealant.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sealed.
34
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
D. Secure the Vent Sections
E. Disassemble Vent Sections
• Vertical runs of DVP pipe must be supported every 8 ft.
(2.44 m) after the 25 ft. (7.62 m) maximum unsupported
rise.
• Rotate either section (see Figure 8.10) so the seams
on both pipe sections are aligned as shown in Figure
8.11.
• Vertical runs of SLP pipe must be supported every 8 ft.
(2.44 m).
• Pull carefully to separate the pieces of pipe.
• Horizontal sections must be supported every 5 feet
(1.52 m).
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support. See Figures 10.8 and 10.9.
• Wall shield firestops may be used to provide horizontal
support.
• SLP ceiling firestops have tabs that may be used to
provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below
connection point to appliance.
Figure 8.10 Rotate Seams for Disassembly
Figure 8.8 Securing Vertical Pipe Sections
Figure 8.11 Align and Disassemble Vent Sections
Figure 8.9 Securing Horizontal Pipe Sections
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
35
F. Install Decorative Ceiling Components
(SLP only)
LEVEL
A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
CATHEDRAL CEILING
SUPPORT BOX
• Seal the gap between the vent pipe and firestop using
high temperature silicone to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to
the ceiling and attaching it using the provided screws.
2 in. (51 mm) MIN. BELOW
FINISHED CEILING
A decorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
• Remove shingles or other roof covering as necessary to
cut the rectangular hole for the support box. Cut the hole
1/8 in. (3 mm) larger than the support box outline.
CUT HOLE 1/8 in. (3 mm)
GREATER IN SIZE THAN
PATTERN OF SUPPORT
BOX AS IT IS PROJECTED
ONTO ROOF LINE
Figure 8.12
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm) below the ceiling (Figure
8.12).
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 8.13.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
36
Figure 8.13
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
G. Install Metal Roof Flashing
Note: Skip this section if using the RF4-8.
• See minimum vent heights for various pitched roofs
(Figure 8.14) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 8.15.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
Figure 8.15
LOWEST
DISCHARGE
OPENING
H. Assemble and Install Storm Collar
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft.
Flat to 6/12........................................ 1.0*
Over 6/12 to 7/12 ............................ 1.25*
Over 7/12 to 8/12 .............................. 1.5*
Over 8/12 to 9/12 .............................. 2.0*
Over 9/12 to 10/12 ............................. 2.5
Over 10/12 to 11/12 ......................... 3.25
Over 11/12 to 12/12 ........................... 4.0
Over 12/12 to 14/12 ........................... 5.0
Over 14/12 to 16/12 ........................... 6.0
Over 16/12 to 18/12 ........................... 7.0
Over 18/12 to 20/12 ........................... 7.5
Over 20/12 to 21/12 ........................... 8.0
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
• Connect both halves of the storm collar with two screws
(see Figure 8.16).
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
is tight against the pipe section.
• Slide the assembled storm collar down the pipe section
until it rests on the roof flashing (see Figure 8.17).
• Caulk around the top of the storm collar (see Figure 8.23).
* 3 foot minimum in snow regions
Figure 8.14 Minimum Height From Roof To Lowest Discharge
Opening
Figure 8.16 Assembling the Storm Collar
NOTICE: Failure to properly caulk the roof flashing could
cause water entry.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 8.15.
Figure 8.17 Assembling the Storm Collar Around the Pipe
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
37
I. Install RF4-8
The RF4-8 may be used in place of the roof flashing and
storm collar (Sections 8.F. and 8.I.)
Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FS when using the RF48 Flashing. Refer to Section 8.D Securing Vent Sections.
SECURE WITH 4
SCREWS NO LONGER
THAN 1 IN. (25 MM)
Figure 8.20 Apply Sealant
SLP-FS
Figure 8.18 Secure Pipe with SLP-FS
• Trim the rubber boot (using scissors or a utility knife),
cutting along the marked measurement lines. See Figure
8.19. Use the 150 mm line for SLP, 210 mm for DVP.
• Lubricate pipe or flue with water and slide the flashing
down. It may be necessary to trim the top shingles around
the base of the rubber boot to ensure a good fit.
APPLY SEALANT
TOP & PARTIAL SIDES
• Draw around flashing, remove.
• Apply silicone sealant to roof inside the lines (Figure 8.20)
• Lubricate pipe or flue with water and slide flashing down.
Seat firmly in sealant. Nail roof flashing to the roof.
• Apply silicone sealant on the top outside of the 8.21.
Install shingles, Apply sealant at the top edge of the
rubber boot. See Figure 8.22.
• We recommend that you top coat with conventional
acrylic house paint to improve the appearance of your
galvanized base flashing.
Figure 8.21 Slide Flashing Down, Secure & Apply Sealant
SILICONE SEALANT
(TOP OF BOOT)
SHINGLES TRIMMED
FLASHING OVER
SHINGLES
SHINGLES OVER
FLASHING
Figure 8.22 Installation Complete
Figure 8.19 Trim Rubber Boot
38
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
J. Install Vertical Termination Cap
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of the
cap into the outer flue of the pipe (see Figure 8.23).
TERMINATION CAP
L. Heat Shield Requirements for Horizontal
Termination
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thickness.
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.25).
• Heat shields must overlap 1-1/2 in. (38 mm) minimum.
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 8.25.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
and wall shield firestop must to be trimmed. A minimum
1-1/2 in. (38 mm) overlap MUST be maintained.
(1 of 3)
STORM
COLLAR
SCREWS
CAULK
• Use an extended heat shield if the finished wall thickness
is greater than 7-1/4 in. (184 mm).
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
• Attach the extended heat shield to either of the existing
heat shields using the screws supplied with the extended
heat shield. Refer to vent components diagrams in the
back of this manual.
Figure 8.23
K. Install Decorative Wall Components (SLP
only)
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the firestop.
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
Important Notice: Heat shields may not be field constructed.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have been
connected, slide the wall thimble up to the interior wall
surface and attach with screws provided. See Figure
8.24.
Figure 8.24 Wall Thimble
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
39
M. Install Horizontal Termination Cap
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
Failure to maintain overlap may cause overheating and
fire.
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
HEAT SHIELD OR
EXTENDED
HEAT SHIELD
HEAT SHIELD
1-1/2 IN. (38 MM) MIN.
OVERLAP
WALL SHIELD
FIRESTOP
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
• Flash and seal as appropriate for siding material at
outside edges of cap.
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
SLIP SECTION
CAN BE EXTENDED
INNER VENT
INTERIOR
CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone
from touching the hot cap.
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit and
HRC caps are available. When penetrating a brick wall, a
brick extension kit is available for framing the brick.
SHEATHING
OUTER VENT
EXTERIOR
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
Figure 8.25 Venting through the wall
Termination Cap Specification Chart
(depth without using additional pipe sections)
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2
Top Vent
Rear Vent
Top Vent
Rear Vent
Depth
Depth
Depth
Depth
3-1/8 in. to
5-1/2 in. to
N/A
N/A
5 in.
9-1/2 in.
SL Series
DVP-HPC1
Top Vent
Depth
N/A
DVP-HPC1
Rear Vent
Depth
3-1/8 in. to
5-1/4 in.
DVP-HPC2
Top Vent
Depth
N/A
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8 in.)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)
40
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
DVP-HPC2
Rear Vent
Depth
5-1/4 in. to
9-3/8 in.
9
Gas Information
A. Fuel Conversions
C. Gas Connection
Before making gas connections ensure that appliance being installed is compatible with the available gas type.
Any natural or propane gas conversions necessary to
meet the appliance and locality needs must be made by
a qualified technician using Hearth & Home Technologies
specified and approved parts.
Note: Have the gas supply line installed in accordance
with local building codes, if any. If not, follow ANSI
223.1. Installation should be done by a qualified installer
approved and/or licensed as required by the locality. (In
the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter).
B. Gas Pressures
Proper input pressures are required for optimum appliance performance. Gas line sizing requirements need to
be made following NFPA 54.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Note: A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13 mm) T-handle manual shut-off valve and
flexible gas connector are connected to the 1/2 inch (13 mm)
control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
Refer to Reference Section 16 for location of gas line
access in appliance.
Note: Gas line may be run from either side of the appliance
provided the hole in the outer wrap does NOT exceed 2-1/2
inches in diameter and does not penetrate the firebox.
WARNING
Gas Leak Risk
• Support control when attaching pipe to
prevent bending gas line.
WARNING
Verify inlet pressures.
• High pressure may cause overfire condition.
• Low pressure may cause explosion.
• Verify minimum pressures when other
household gas appliances are operating.
Install regulator upstream of valve if line
pressure is greater than 1/2 psig.
Note: The gap between supply piping and gas access hole
may be caulked with high temperature caulk or stuffed with
non-combustible, unfaced insulation to prevent cold air
infiltration.
Pressure requirements for appliance are shown in the
table below. Minimum pressures must be met when other
household gas appliances are operating.
Pressure
Natural Gas
Propane
Minimum inlet pressure
5.0 inches
w.c.
11.0 inches
w.c.
Maximum inlet gas pressure
14.0 inches
w.c.
14.0 inches
w.c.
Manifold pressure
3.5 inches
w.c.
10.0 inches
w.c.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
41
• Ensure that gas line does not come in contact with outer
wrap of appliance. Follow local codes.
• Incoming gas line should be piped into the valve
compartment and connected to the 1/2 inch connection
on the manual shutoff valve.
WARNING
Fire or Explosion Hazard
•
•
•
•
Gas buildup during line purge may ignite.
Purge should be performed by qualified technician.
Ensure adequate ventilation.
Ensure there are no ignition sources such as
sparks or open flames.
HIGH ALTITUDE INSTALLATIONS
U.L. Listed gas appliances are tested and approved without
requiring changes for elevations from 0 to 2000 feet in the
U.S.A. and Canada.
When installing this appliance at an elevation above 2000 feet,
it may be necessary to decrease the input rating by changing
the existing burner orifice to a smaller size. Input rate should
be reduced by 4% for each 1000 feet above a 2000 foot
elevation in the U.S.A., or 10% for elevations between 2000
and 4500 feet in Canada. If the heating value of the gas has
been reduced, these rules do not apply. To identify the proper
orifice size, check with the local gas utility.
If installing this appliance at an elevation above 4500 feet (in
Canada), check with local authorities.
• A small amount of air will be in the gas supply lines.
When first lighting appliance it will take a short time for
air to purge from lines. When purging is complete the
appliance will light and operate normally.
WARNING
CHECK FOR GAS LEAKS
Explosion Risk
Fire Risk
Asphyxiation Risk
• Check all fittings and connections.
• Do not use open flame.
• After the gas line installation is complete, all
connections must be tightened and checked
for leaks with a commercially-available,
non-corrosive leak check solution. Be sure
to rinse off all leak check solution following
testing.
Fittings and connections may have loosened
during shipping and handling.
WARNING
Fire hazard.
Do NOT change the valve settings.
• This valve has been preset at the factory.
• Changing valve settings may result in fire
hazard or bodily injury.
42
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
10
Electrical Information
A. Recommendation for Wire
B. Connecting to the Appliance
This appliance requires 110-120 VAC be wired to the
junction box either for use of optional accessories (standing pilot ignition) or for proper operation of the appliance
(Intellifire ignition). Refer to Figure 10.1 to determine if the
appliance uses an Intellifire ignition system or Standing
Pilot ignition system.
Remove the front or open the control access panel to view
wiring system and gas valve. If this appliance has a red
or black ignitor button (as noted in Figure 10.1) this appliance has a Standing Pilot ignition system. If there is no
red or black ignitor button, this appliance has an Intellifire
ignition system.
WARNING
Wire 110V to electrical junction box.
Do NOT wire 110V to valve.
Do NOT wire 110V to wall switch.
• Incorrect wiring will damage millivolt valves.
• Incorrect wiring will override IPI safety lockout
and may cause explosion.
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
• If using thermostat use one compatible with a millivolt
gas valve system.
• Follow parameters for locating thermostat (see individual
thermostat instructions) to ensure proper operation of
appliance.
• Use low resistance thermostat wire for wiring from ignition system to the wall switch and thermostat.
• Keep wire lengths short as possible by removing any
excess wire length.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
Figure 10.1 Standing Pilot Ignition
• Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
Note: This appliance must be electrically wired and grounded
in accordance with local codes or, in the absence of local
codes, with National Electric Code ANSI/NFPA 70-latest
edition or the Canadian Electric Code, CSA C221.1.
PILOT
THERMOPILE
THERMOCOUPLE
WHITE
PIEZO
THERMOSTAT
WIRE ASSEMBLY
RED
VALVE
Figure 10.2 Standing Pilot Ignition Wiring Diagram
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
43
C. Intellifire Ignition System Wiring
CAUTION
This appliance requires a 110 VAC supply to the appliance
junction box for operation. A wiring diagram is shown in
Figure 10.3 and Figure 10.4.
Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
This appliance is equipped with an Intellifire control valve
which operates on a 3 volt system.
This appliance is supplied with a battery pack and a 3 volt AC
transformer, which requires the installation of the supplied
junction box. It is highly recommended that the junction box
be installed at this time to avoid reconstruction.
D. Standing Pilot Ignition System Wiring
The battery pack requires two D cell batteries (not
included).
• It is recommended that a 110 VAC junction box be installed for use with a fan or remote control. (See Figure
10.5 for junction box wiring).
• This standing pilot ignition system wiring does not require
a 110 VAC supply to operate.
Batteries cannot be placed in the battery pack while
using the 3 volt AC transformer. The transformer must
be unplugged if the battery pack is used or battery life
will be reduced.
WARNING
Shock hazard.
• Replace damaged wire with type 105º C
rated wire.
• Wire must have high temperature insulation.
CAUTION
Do not wire 110 VAC directly to ignition module. Permanent
damage to module will occur. Connect ignition module to 3
VAC transformer as instructed.
CAUTION
Battery polarity must be correct or module damage will occur.
IGNITION
MODULE 3 VAC
INTERMITTENT
PILOT IGNITOR
I
S
TRANSFORMER
3 VAC
ORANGE
NEUTRAL
HOT
WHITE
PLUG IN
GROUND TO
FIREPLACE
CHASSIS
K
AC
BL
D
RE
ORANGE
GREEN
WIRES
(TO BROWN)
BATTERY PACK
THERMOSTAT
WIRE ASSEMBLY
VALVE
NOTE: 1. Ignition module, valve, pilot, and
wall switch operate on 3 volts. 120 VAC is
required at junction box unless equipped
with battery back-up.
Figure 10.3 Intellifire Ignition Wiring Diagram with Wall Switch or Thermostat
44
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
IGNITION
MODULE 3 VAC
INTERMITTENT
PILOT IGNITOR
I
S
TRANSFORMER
3 VAC
ORANGE
NEUTRAL
HOT
WHITE
PLUG IN
GROUND TO
FIREPLACE
CHASSIS
K
AC
BL
D
RE
ORANGE
GREEN
WIRES
(TO BROWN)
BATTERY PACK
REMOTE
PLUG IN
VALVE
Figure 10.4 Intellifire Ignition Wiring Diagram with Remote Receiver
NOTE: 1. Ignition module, valve, pilot, and
wall switch operate on 3 volts. 120 VAC is
required at junction box unless equipped
with battery back-up.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
45
E. Junction Box Installation
Romex
Connector
If the box is being wired from the OUTSIDE of
the appliance:
• Remove the cover plate located on the outer
shell - right side (see Figure 10.5).
14/2WG
• Install the supplied Romex™ connector in the
cover plate.
Cover Plate
outside firebox
• Feed the necessary length of wire through the connector.
HT
WHT B
LK
BLK
W
• Make all necessary wire connections and reattach the cover plate to the outer shell.
If the box is being wired from the INSIDE of the
appliance:
GRN wire
inside box
• Remove the screw attaching the junction box/
receptacle to the outer shell, rotate the junction
box inward to disengage it from the outer shell
(see Figure 10.5).
Figure 10.5 Junction Box Detail
Copper
ground attached
to GRN screw with
GRN wire
NOTE: Do NOT wire
110VAC to wall switch.
• Pull the electrical wires from outside the appliance through this opening into the valve compartment.
• Feed the necessary length of wire through the
connector.
• Make all necessary wire connections to the
junction box/receptacle and reassemble the
junction box/receptacle to the outer shell.
F. Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall
mounted switch for use with a fan (See
Figure 10.6):
SWITCH
• The power supply for the appliance
must be brought into a switch box.
Red
Black
White
Green
Black
White
Green
JUNCTION BOX
Red
Black
White
Green
• The power can then be supplied from
the switch box to the appliance using
a minimum of 14-3 with ground wire.
MINIMUM 14-3
AW G
WITH GROUND
• At the switch box connect the black
(hot) wire and red (switch leg) wire to
the wall switch as shown.
POWER
SUPP LY WIRE S
SWITCH BOX
• At the appliance connect the black (hot),
white (neutral) and green (ground)
wires to the junction box as shown.
• Add a 1/4 inch insulated female connector to the red (switch leg) wire, route
it through the knockout in the face of
the junction box, and connect to the top
fan switch connector (1/4 inch male) as
shown.
46
Red
Figure 10.6 Junction Box Wired to Wall Switch
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
11
Finishing
A. Mantel Projections
Figure 11.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels
or other combustible projections above the top front edge
of the appliance.
All measurements
are in inches
1/2 IN.
MINIMUM
CEILING
2-7/8 IN.
MINIMUM
12
11
10
9
8
32
7
6
5
4
3
4
5
6
7
9
8
10
11
12
3 FT. MAXIMUM
Note: Clearance from opening
to perpendicular wall.
13
Figure 11.3 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
TOP OF HOOD OR FIREPLACE OPENING
Figure 11.1 Clearances to mantels or other combustibles
above appliance
1/2 in.
SHEETROCK
3-1/2 in.
3 IN.
MINIMUM
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
5-3/8 IN.
MINIMUM
UNLIMITED
Note: Clearance from opening
to perpendicular wall.
1/2 in.
Figure 11.4 Wall Projection (Acceptable on one side of opening.)
NON-COMBUSTIBLE ZONE
Figure 11.2 Non-Combustible Zone
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
47
B. Facing Material
Note: There are 3 metal tabs holding the non-combustible
board in place for shipping. These tabs are to be cut off or
bent back before finishing around the appliance front.
WARNING
Fire Risk.
Do NOT obstruct air inlet or outlet grilles.
Do NOT modify grilles.
• Modifying or covering grilles could cause
temperature rise and fire hazard.
Finishing materials must not interfere with:
• Air flow through grilles or louvers.
• Operation of louvers or doors.
• Access for service.
FACING MATERIAL UP TO 1/2 IN. THICK
MAY BE COMBUSTIBLE - TOP AND SIDES
NON-COMBUSTIBLE
BOARD (INCLUDED)
0 IN.
WARNING
Fire Risk.
Finish all edges and fronts to clearances and
specifications listed in manual.
• Do NOT overlap combustible materials onto appliance
front. The appliance front may only be covered with
noncombustible materials. The bottom one inch of the
appliance front is exempt and may be covered with either
non-combustible or combustible materials.
• Install combustible materials only up to specified
clearances on top, front and side.
• Seal joints between the finished wall and appliance top
and sides using only a 300º F minimum sealant.
1 IN.
1 IN.
1 IN.
0 IN.
0 IN.
HIGH TEMPERATURE (300º F / 149º C MIN.)
TOP & SIDE SEAL JOINT
Figure 11.4 Facing Material
WARNING
Risk of Fire
• Non-combustible clearances MUST be
maintained.
• Sheetrock, wood or other combustibles must
NOT be used as sheathing or facing in the
non-combustible zone.
• See Section 11 for proper clearances.
• See Section 1 for combustible/noncombustible definitions.
48
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
C. Splatter Guard
The splatter guard is a piece of corrugated material used
to protect the appliance during the installation process before finishing work on the whole hearth is complete.
Splatter guards may be factory installed or accompany the
door of the unit, depending on the fireplace model. Splatter guards must be removed before appliance is fired.
WARNING
Risk of Fire
• Splatter guard must be removed before lighting
appliance.
• Before splatter guard is installed:
Close ball valve to prevent accidental lighting.
Step 1. Turn off gas to valve. Red gas shutoff knob is
located on ball valve. Disconnect the 3 volt transformer
from the junction box. See Figure 11.5.
Figure 11.7
Step 4. Center the splatter guard in front of the unit as
shown in Figure 11.8. Place the splatter guard in the unit
by guiding the top flap into proper position and then continuing to guide the tabs on the side flaps into the top slot
on the left and right sides of the appliance. The top slot
is indicated in Figure 11.9 Take care not to bend or break
off the tabs.
Figure 11.5
To install the Splatter Guard:
Step 2. Crease flap on top side of splatter guard using the
scored line as the guide. See Figure 11.6.
Figure 11.8
TOP SLOT
Figure 11.6
Step 3. Crease flaps on left and right sides of splatter guard
using the scored line as the guide. See Figure 11.7.
Figure 11.9
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
49
Step 5. Fold bottom flap along score line as indicated
in Figure 11.10 and tuck into valve access area of appliance. Splatter guard should fit securely on front of unit.
Figure 11.13
Once plumbing and wiring are complete on the fireplace,
the lower access panel may be closed until the time that the
splatter guard must be removed for firing the appliance.
Figure 11.10
Figure 11.14
To Close the Lower Access Panel:
Figure 11.11
Step 6. To open lower access panel of splatter guard,
place one hand above score line and place two fingers
from other hand in the round holes on the front of the
splatter guard. See Figure 11.11 Pull out and fold up the
panel as shown in Figure 11.12. Disengage the tabs on
left and right bottom of splatter guard and fit them into
the square holes. The tabs are now inside the front of
the splatter guard; carefully bend them down See Figure
11.13.
Carefully disengage the tabs from the square holes and
bend the access panel to its original position. Bend the
center bottom flap and insert it into the bottom of the appliance.
Figure 11.15
To Remove the Splatter Guard:
Figure 11.12
50
Carefully grab splatter guard on or near the vertical center
on the left and right sides. Pull outward gently, but firmly,
taking care not to tear or remove the inserted tabs.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
D. Doors
It’s very important to know what kind of a door and what kind
of finishing material is going to be used on the fireplace. The
table below shows the door models and the finishing material thickness allowed. For an inside fit there is an available
template to assist with sizing the finishing material.
UNITS AND
TEMPLATE PART #
FINISHING MATERIAL
4 IN. MAXIMUM
THICKNESS
FINISHING MATERIAL
4 IN. MAXIMUM
THICKNESS
DOOR
SL-350TRS-IPI (350-Template)
SL-550TRS-IPI-E, SL-550TRS-E (550-Template)
SL-750TRS-IPI-E, SL-750TRS-E (750-Template)
DOOR
FIT
FINISH MATERIAL
THICKNESS
SEE
FIGURE
X
Y
Aero-28
Inside
4 inches Max.
11.16
N/A
N/A
Aero-32
Inside
4 inches Max.
11.16
N/A
N/A
Aero-36
Inside
4 inches Max.
11.16
N/A
N/A
Chad-28E
Overlap
1 inch Max.
11.17
N/A
N/A
Chad-28E
Inside
1-4 inches
11.18
29-3/8 in.
28-3/8 in.
Chad-32E
Overlap
1 inch Max.
11.17
N/A
N/A
Chad-32E
Inside
1-4 inches
11.18
32-3/8 in.
30-3/8 in.
Chad-36E
Overlap
1 inch Max.
11.17
N/A
N/A
Chad-36E
Inside
1-4 inches
11.18
37-1/4 in.
34 in.
Halston-28E Overlap
1 inch Max.
11.17
N/A
N/A
Halston-28E
1-4 inches
11.19
29-3/8 in.
28-3/8 in.
Inside
Halston-32E Overlap
1 inch Max.
11.17
N/A
N/A
Halston-32E
1-4 inches
11.19
32-3/8 in.
30-3/8 in.
Inside
Halston-36E Overlap
1 inch Max.
11.17
N/A
N/A
Halston-36E
1-4 inches
11.19
37-1/4 in.
34 in.
Inside
Y
X
(Includes 1/8 in. opening each side of door)
Finishing material between 1 and 4 inches thick.
Refer to Table 1 for X and Y dimensions.
Figure 11.18 Inside Fit Door (Chad)
Table 1. Finishing Clearances for Aero, Chad and Halston Fronts
FINISHING
MATERIAL
FINISHING
MATERIAL
FINISHING MATERIAL
4 IN. MAXIMUM THICKNESS
DOOR
FINISHING MATERIAL
4 IN. MAXIMUM THICKNESS
*IF FINISHING MATERIAL IS THICKER THAN
2 IN., DOORS WILL ONLY OPEN
AS FAR AS PICTURED
Stop finishing material flush with fireplace surround opening.
DOORS
Figure 11.16 Aero Door
Y
FRONT FACE OF FIREPLACE
DOOR
1 in. MAX
FINISHING MATERIAL
(TOP EDGE)
Finishing materials 1 inch maximum thick.
Stop finishing material flush with opening.
Figure 11.17 Overlap Fit Door (Chad and Halston)
X
(Includes 1/8 in. opening each side of door)
Finishing material between 1 and 4 inches thick.
Refer to Table 1 for X and Y dimensions.
Figure 11.19 Operable Hinge Door (Halston)
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
51
12
Appliance Setup
A. Remove Shipping Materials
D. Lava Rock, Mineral Wool/Ember Placement
Remove shipping materials from inside or underneath the
firebox.
Placing the Lava Rock (SL-350TRS-IPI only)
See Section 12F for Lava Rock placement instructions.
B. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
C. Accessories
Install only approved accessories per instructions included
with accessories. See your dealer or visit www.heatnglo.
com for appropriate accessories.
WARNING
WARNING
Explosion Risk.
• Follow ember placement instructions in manual.
• Do NOT place embers directly over burner ports.
• Replace ember material annually.
Improperly placed embers interferes with proper burner
operation.
Placing the Ember Material
Shock or fire risk.
Use ONLY optional accessories approved for
this appliance.
• Using non-listed accessories voids warranty.
• Using non-listed accessories may result in a
safety hazard.
• Only Hearth & Home Technologies approved
accessories may be used safely.
Ember material is shipped with this gas appliance. To place
the ember material:
• Embers CANNOT be placed directly over ports. See
Figure 12.4 for the only exception to this guideline. Care
should be taken not to cover the lighting trail of ports
(from back to front).
• When placing Glowing Embers® onto the burner care should
be taken so that the ports are not covered. Place the dimesize ember pieces near the port holes in the burner top (see
Figure 12.3 and 12.5). Failure to follow this procedure will
likely cause lighting and sooting problems.
• Place Mytic Embers on areas of base refractory away from
port holes. Use this material to give the appliance a realistic
ash bed (SL-550TRS-IPI-E and SL-750TRS-IPI-E only).
• Save the remaining ember materials for use during appliance servicing. The embers provided should be enough
for 3 to 5 applications.
RHEOSTAT
SWITCH
TEMPERATURE
SENSOR
Figure 12.1 Fan Wiring with Rheostat
VARIABLE
SPEED SWITCH
JUNCTION BOX
EMBER MATERIAL
TEMPERATURE
SENSOR SWITCH
Figure 12.3 Placement of Embers
BLUE
Figure 12.2 Detail of Fan Wiring with Rheostat
52
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
PORT HOLES IN SHADED
AREA SHOULD BE COVERED
WITH EMBER MATERIAL. NO
OTHER PORT HOLES MAY
COME INTO CONTACT WITH
EMBER MATERIAL.
Figure 12.6
Figure 12.4
Step 2.
Place the right refractory against the firebox right wall such
that it is against the back refractory (see Figure 12.7).
EMBER MATERIAL
Figure 12.5 Placement of Embers
E. Install Refractory
SL-550TRS-IPI-E, SL-550TRS-E, SL-750TRS-IPI-E and
SL-750TRS-E only.
CAUTION
Figure 12.7
Step 3.
Bend left and right refractory retainer tabs to keep side
pieces from tipping (see Figure 12.8).
Refractory is fragile! Carefully remove the refractory from the
packaging.
Step 1.
Remove the logs from the fireplace. Place the back wall
refractory centered against the back of the fireplace on
top of the grate tabs. While steadying the back piece
with one hand, place the left refractory against the firebox left wall such that it is against the back refractory
(see Figure 12.6).
REFRACTORY
RETAINER TAB
Figure 12.8
Step 4.
Install logs according to the install manual.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
53
F. Positioning the Logs
Log Set Assembly: LOGS-350TRS-D
Model: SL-350TRS-D,SL-350TRS-IPI
Note: Figure 1 illustrates the recommended gap between the
burner and the lava rock retainer.
3/8 in.
Burner
Lava Rock
retainer
No lava rock
may be placed
past this edge.
Figure 1
Left rear log tab
Left rear log tab
Groove used to locate log # 2
Right rear log tab
1
Shoulder screw
Lava rock retainer
Grate tine (4)
Figure 2
Mate slot with tab
Figure 3
CAUTION: Logs are fragile. Log #1 (SRV2113-701): Locate the slot on the bottom right side of log 1. Mate the slot with the
right rear log tab. Pull the front left nose of log #1 forward until it touches the left rear log tab.
Mate log with groove on log # 1
Tip should touch log # 2
Groove used to locate log # 3
3
2
Log # 1 should rest on log # 1
Swing branch towards burner
Mate log with tine
Figure 4
Log #2 (SRV2113-702):Locate the notch at the left end of
log # 2. Mate the notch with the tine as shown above. The
top end of log #4 should rest on the groove that is located
on the top of log #1. Swing the center branch toward the
burner (see above).
54
Mate “Y” with groove
Figure 5
Log #3 (SRV2113-704): Locate the “Y” end of log # 3. Mate
the “Y” end with the groove on log # 2 (see above illistration).
Log # 3 should rest on log # 2, as shown above. The tip of
log #3 should touch log # 2.
2113-935C
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
Mate shoulder screw with notch
4
Figure 6
Mate groove and grate tine
Figure 7
Lava Rock
Log #4 (SRV2113-703): Locate the notch on the bottom of log # 4. Mate the notch with the shoulder screw that is located on the
burner top. Mate the rear groove with the far right grate tine as shown above. Apply the supplied lava rock as shown above.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
55
Model: SL-550TRS-IPI-E
Log Set Assembly: LOGS-SL550TRS-D
STEP 1.
CAUTION: Logs are fragile!
Carefully remove the logs from the packaging.
1
4
3
2
5
LOG NOTCHES
1
STEP 2.
LOG #1 (SRV2065-701) Place log #1 on left flat side of
the burner assembly. Pull the log and slide it to the right
until the notches under the log are in the burner grooves.
2
1
STEP 3.
LOG #2 (SRV2065-702) Place log #2 on the grate bar
and push it back against the refractory. The pilot should
be centered within the large notch on log #2.
2065-935i 11/07
56
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
2
3
1
STEP 4.
LOG #3 (SRV2065-703) Place log #3 on right side of
grate. The notch on the log should fit over the bar on the
far right side of the grate. Push the right side of log #3
against the grate tab and pull the left side forward until it
comes into contact with the burner detail.
LOG/BURNER DETAIL CONTACT AREA
Figure 1.
LOG TOUCHES REFRACTORY PANEL
4 2
1
STEP 5.
LOG #4 (SRV2065-704) Place log #4 so that the notch
is touching the first grate tine and is laying in the flat spot
of log #2. The right end of log #4 should touch the back
refractory panel. See Figure 2.
3
NOTCH
Figure 2.
LOG #5/REFRACTORY PANEL CONTACT POINTS
5
STEP 6.
LOG #5 (SRV2065-705) Place log #5 on log #2. The
front left of the log will rest on log #4. Log 5 must be
pushed back against refractory. See Figure 3.
4 2
1
3
Figure 3.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
57
Model: SL-750TRS-IPI-E
Log Set Assembly: LOGS-SL750TRS- D
STEP 1.
CAUTION: Logs are fragile!
Carefully remove the logs from the packaging.
1
2
3
4
5
LOG NOTCHES
1
STEP 2.
LOG #1 (SRV2065-701) Place log #1 on left flat side of
the burner assembly. Pull the log forward and slide it to
the right until the notches under the log are in the burner
grooves.
2
1
STEP 3.
LOG #2 (SRV2066-702) Place log #2 on the grate bar
and push it back against refractory. The pilot should be
centered within the large notch on log #2.
2066-935H 11/07
58
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
2
NOTCH
3
STEP 4.
LOG #3 (SRV2066-703) Place log #3 on right side of
grate. The notch on the log should fit over the bar on the
far right side of the grate. Push the right side of log #3
against the grate tab and pull the left side forward until
it comes into contact with the burner detail as shown in
Figure 1.
1
LOG/BURNER DETAIL CONTACT AREA
Figure 1.
LOG TOUCHES REFRACTORY PANEL
2
4
3
1
NOTCH
STEP 5.
LOG #4 (SRV2066-704) Place log #4 so that the notch
is touching the first grate tine and is laying in the flat spot
of log #2. The right end of log #4 should touch the back
refractory panel. See Figure 2.
Figure 2.
MATE WITH GROOVES HERE
5
2
4
3
1
STEP 6.
LOG #5 (SRV2066-705) Place log #5 on log #2. Log #5
will mate with the grooves located on the top side of Log
#4. See Figure 3.
Figure 3.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
59
G. Glass Assembly
WARNING
Handle glass doors with care.
• Inspect the gasket to ensure it is undamaged.
• Inspect the glass for cracks, chips or scratches.
• Do NOT strike, slam or scratch glass.
• Do NOT operate appliance with glass door removed,
cracked, broken or scratched.
• Replace glass door assembly as a complete appliance.
Removing Glass Assembly
Pull the four glass assembly latches out of the groove on
the glass frame. Remove glass door from the appliance
(see Figure 12.2).
Replacing Glass Assembly
Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame.
H. Grilles and Trim
Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other noncombustible
materials can be used to cover up the gap between the
sheet rock and the appliance.
Do not obstruct or modify the air inlet/outlet grilles. When
overlapping on both sides, leave enough space so that the
bottom grille can be lowered and the trim door removed.
I. Air Shutter Setting
This appliance has an adjustable air shutter (which controls the primary air) factory set for the minimum vertical
vent run (see Figure 12.3). If your installation has more
than the minimum required vertical vent length, adjustment of the air shutter may be necessary to obtain optimal
flame appearance. This should be adjusted by a qualified installer at the time of installation.
By sliding the air shutter to the right, you will be closing
the air shutter. To adjust loosen the wing nut. Care should
be taken when adjusting the air shutter so as not to cause
the appliance to soot. If sooting occurs the air shutter will
need to be opened by sliding the air shutter to the left.
When finished, tighten wing nut.
LATCHES
(BOTH BOTTOM
AND TOP)
GLASS
ASSEMBLY
Figure 12.2 Glass Assembly
S H U TTE R A D JU S TM E N T
Figure 12.3
Shutter settings
60
SL-350TRS-IPI
3/16 in.
SL-350TRS-IPI (LP)
1/4 in.
SL-550TRS-IPI-E
SL-550TRS-E
3/8 in.
SL-550TRSIPILPE
SL-550TRSLP-E
Fixed
SL-750TRS-IPI-E
SL-750TRS-E
3/8 in.
SL-750TRSLPIPIE
Fixed
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
13
Operating Instructions
A. Before Lighting Appliance
Before lighting this appliance determine if it has a Standing Pilot or Intellifire ignition system by opening the control access panel to view wiring system and gas valve. If
this appliance has a red or black ignitor button (see Figure
10.1) this appliance has a Standing Pilot ignition system.
If there is no red or black ignitor button, this appliance has
an Intellifire ignition system.
CAUTION
If installing Intellifire ignition battery backup:
• Do not install batteries if the backup mode may not be
used for extended time.
• Batteries may leak.
• Install batteries only when needed for power outage.
Before operating this appliance have a qualified technician:
• Remove all shipping materials from inside and/or
underneath the firebox.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. Do
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
• Review proper placement of logs, rockwool, lava rock,
and vermiculite.
WARNING
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
• Ensure that the glass is sealed and in the proper
position.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to
the owner’s information manual provided with this appliance.
For assistance or additional information consult a qualified
installer, service agency or the gas supplier.
• Ensure that the flow of combustion and ventilation air is
not obstructed (front grilles and vent caps).
WARNING
WARNING
Glass door must be in place when
appliance is operating.
Risk of:
• Combustion Fumes
• Fire
Do NOT operate appliance with glass
door removed.
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
• Open viewing glass for servicing only.
• Glass door MUST be in place and sealed before operating
appliance.
• Only use glass door certified for use with appliance.
• Glass replacement should be done by qualified technician.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
61
B. Lighting Instructions (IPI)
The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burner. DO NOT try to light the burner by
hand.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
C. DO NOT use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
LIGHTING
INSTRUCTIONS
(IPI)
1. Turn off all electric power to the appliance.
2. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
• If you cannot reach your gas supplier, call the fire department.
• DO NOT touch any electric switch; do
not use any phone in your building.
GAS
VALVE
3. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this label. If you do not smell gas, go to next step.
4. Turn on all electric power to the appliance.
WARNING:
CAUTION:
DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gasoline and other liquids having flammable
vapors away.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause cancer, birth defects, or other reproductive
harm.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
NOT FOR USE
WITH SOLID FUEL
5. To light the burner, flip the ON/OFF switch to
the “ON” position. (The ON/OFF switch may
include a wall switch if so equipped).
6. If the appliance will not operate, follow the instructions “To Turn Off Gas to Appliance” and
call your service technician or gas supplier.
TO TURN OFF
GAS TO APPLIANCE
1. Turn wall control or ON/OFF switch to “OFF”.
2. Turn off all electric power to the appliance if
service is to be performed.
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Final inspection by
62
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
593-913F
Standing Pilot Ignition
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
1. Open control access panel.
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which
must be lighted by hand. When
lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or
turn the gas control knob. Never use
tools. If the knob will not push in or
turn by hand, DO NOT try to repair
it, call a qualified service technician.
Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WARNING:
CAUTION:
DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gasoline and other liquids having flammable
vapors away.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause cancer, birth defects, or other reproductive
harm.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
NOT FOR USE
WITH SOLID FUEL
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
2. Turn off all electric power to
the appliance.
3. Push in gas control knob
slightly and turn clockwise
to “OFF”.
Note: Knob cannot be turned from “PILOT” to “OFF”
unless knob is pushed in slightly. DO NOT force.
4. Open the fixed glass assembly. You may need to
remove the decorative front.
5. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow “B” in the Safety
Information located on the left side
of this label. If you don’t smell gas,
go to next step.
6. Find the pilot. The pilot is inside
combustion chamber next to the
main burner
7. Turn knob on gas control counterclockwise
to “PILOT”.
8. Push in control knob all the way and hold in. Immediately depress red or black piezo button. It may require
several depressions of the red or black piezo button
until PILOT lights. If PILOT light does not light after
10 seconds, return to step 3. Continue to hold the
control knob in for about one minute after the pilot is
lit. Release knob and it will pop back out. Pilot should
remain lit. If it goes out, repeat steps 3 through 6.
• If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.
• If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your service technician or gas supplier.
9. Reinstall fixed glass assembly. Reinstall decorative
front.
10. Turn gas control knob counterclockwise
to “ON”. Close access panel.
11. Turn on all electric power to the appliance.
12. To light burner, turn the wall control or on/off switch
to “ON”.
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
TO TURN OFF
GAS TO APPLIANCE
For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
1. Turn off all electric power to the appliance if service is to be performed.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
2. Open control access panel.
3. Move switch to “OFF” position.
4. Push in gas control knob slightly and turn clockwise
to OFF”. DO NOT force.
5. Close control access panel.
Final inspection by
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
464-903H
63
C. After Appliance is Lit
CAUTION
Initial Break-in Procedure
When you light the appliance, you may notice that it produces heat which does have an associated odor or smell.
If you feel this odor is excessive it may require the initial
three to four hour continuous burn on high followed by a
second burn up to 12 hours to fully drive off any odor from
paint and lubricants used in the manufacturing process.
Condensation of the glass is normal.
NOTE: The appliance should be run three to four hours
on the initial start-up. Turn it off and let it cool completely.
Remove and clean the glass. Replace the glass and run
the appliance for an additional 12 hours. This will help to
cure the products used in the paint and logs.
During this break-in period it is recommended that some
windows in the house be opened for air circulation. This will
help avoid setting off smoke detectors, and help eliminate any
odors associated with the appliance’s initial burning.
• Prevent accidental appliance operation when not
attended.
• Unplug or remove batteries from remote control if absent
or if appliance will not be used for an extended period of
time.
• Property damage possible from elevated temperatures.
CAUTION
Smoke and odors released during initial operation.
• Open windows for air circulation.
• Leave room during initial operation.
• Smoke may set off smoke detectors.
Smoke and odors may be irritating to sensitive
individuals.
WARNING
WARNING
Fire Risk.
High Temperatures.
Keep combustible household items away from
appliance.
Do NOT obstruct combustion and ventilation air.
• Do NOT place combustible items on top of or
in front of appliance.
• Keep furniture, draperies away from
appliance.
Fire Hazard.
Keep combustible materials, gasoline and
other flammable vapors and liquids clear of
appliance.
• Do NOT store flammable materials in the
appliance’s vicinity.
• Do NOT use gasoline, lantern fuel, kerosene,
charcoal lighter fluid or similar liquids in this
appliance.
• Combustible materials may ignite.
D. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance is allowed to burn for 20 to 40 minutes.
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may also be released from finishing materials and adhesives used around the
appliance.
Film on the glass
Metallic noise
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Is it normal to see the pilot flame burn In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off when
continually?
ON/OFF is turned off. In a standing pilot system the pilot will always stay on.
64
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
14
Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the
corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.
A. Standing Pilot Ignition System
Symptom
Possible Causes
Corrective Action
1. After repeated triggering a. Defective ignitor.
of the red or black piezo
ignitor button, the spark
b. Defective pilot or misaligned
ignitor will not light the pilot.
electrode (spark at electrode).
Check the spark at the electrode and pilot. If no spark and electrode
wire is properly connected, replace the ignitor.
c. No gas or low gas pressure.
Check the remote shut-off valves from the fireplace. Usually, there
is a valve near the gas main. There can be more than one (1) valve
between the fireplace and the main.
d. No LP in tank.
Check the LP (propane) tank. You may be out of fuel.
a. Defective thermocouple.
Check that the pilot flame impinges on the thermocouple. Clean
and/or adjust the pilot for maximum flame impingement.
2. The pilot will not stay lit
after carefully following the
lighting instructions.
Using match, light the pilot. If the pilot lights, turn off the pilot and
trigger the red piezo ignitor button again. If the pilot lights, an improper gas/air mixture caused the bad lighting and a longer purge
period is recommended. If the pilot will not light, ensure the the gap
at the electrode and pilot is one-eighth (1/8) inch to have a strong
spark. If the gap is OK, replace the pilot.
Ensure that the thermocouple connection at the gas valve is fully
inserted and tight (hand tighten plus 1/4 turn).
Disconnect the thermocouple from the valve, place one millivolt
meter lead wire on the tip of the thermcouple and the other meter
lead wire on the thermocouple copper lead. Start the pilot and hold
the valve knob in. If the millivolt reading is less than 15mV, replace
the thermocouple.
b. Defective valve.
3. The pilot is burning,
a. ON/OFF switch or wires
there is no burner flame ,
defective.
the valve knob is in the ON
position, and the ON/OFF
switch is in the ON position.
If the thermocouple is producing more than 15 millivolts, replace
faulty valve.
Check the ON/OFF switch and wires for proper connections. Place
the jumper wires across the terminals at the switch. If the burner
comes on, replace the defective switch. If the switch is OK, place the
jumper wires across the switch wires at the gas valve. If the burner
comes on, the wires are faulty or connections are bad.
b. Thermopile may not be gener- If the pilot flame is not close enough physically to the thermopile,
ating sufficient millivoltage.
adjust the pilot flame.
Be sure the wire connections from the thermopile at the gas valve
terminals are tight and that the thermopile is fully inserted into the
pilot bracket.
Check the thermopile with a millvolt meter. Take the reading at
TH-TP&TP terminals of the gas valve. The meter should read 325
millivolts minimum, while holding the valve knob depressed in the
pilot position, with the pilot lit, and the ON/OFF switch in the OFF
position. Replace the faulty thermopile if the reading is below the
specified minimum.
With the pilot in the ON position, disconnect the thermopile leads
from the valve. Take a reading at the thermopile leads. The reading should be 325 millivolts minimum. Replace the thermopile if the
reading is below the minimum.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
65
Troubleshooting (continued)
Symptom
3. Continued
Possible Cause
Corrective Action
c. Defective valve.
Turn the valve knob to the ON position. Place the
ON/OFF switch in the ON position. Check the millivolt
meter a the thermopile terminals. The millivolt meter
should read greater than 125mV. If the reading is acceptable, and if the burner does not come on, replace
the gas valve.
d. Plugged burner orifice.
Check the burner orifice for stoppage. Remove stoppage.
e. Wall switch or wires are defective.
Follow the corrective action in Symptom and Possible Cause 1.a above. Check the switch and wiring.
Replace where defective.
4. Frequent pilot outage a. Pilot flame may be too high or too low, or blowproblem.
ing out (high pressure), causing pilot safety to
drop out.
Clean thermocouple and adjust the pilot flame for
maximum flame impingement. Follow lighting instructions carefully.
5. The pilot and main
burner extinguish while
in operation.
a. No LP in tank.
Check the LP (propane) tank. Refill the fuel tank.
b. Inner vent pipe leaking exhaust gases back
into the system.
Check venting system for damage. Replace/repair
improperly assembled pipe sections.
c. Glass too loose and air tight packet leaks in
corners after usage.
Replace glass panel assembly.
d. Bad thermopile or thermocouple.
Replace if necessary.
e. Improper vent cap installation.
Check for proper installation and freedom from debris
or blockage.
a. Flame impingement.
Adjust the log set so that the flame does not excessively impinge on it.
b. Improper air shutter setting.
Adjust the air shutter located on the control panel.
c. Debris around air shutter.
Inspect the opening at the base of the burner. NO MATERIAL SHOULD BE PLACED IN THIS OPENING.
a. Insufficient oxygen being supplied.
Ensure that the vent cap is installed properly and free
of debris. Ensure that the vent system joints are tight
and have no leaks.
6. Glass soots.
7. Flame burns blue
and lifts off burner.
Ensure that no debris has been placed at the base of,
or in the area of the air holes in the center of the base
pan beneath the burner.
Ensure that the glass is tightened properly on the unit,
particularly on top corners.
66
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
B. Intellifire Ignition System
Sympton
1. The ignitor/module
makes noise, but no
spark.
2. Pilot won’t light,
there is no noise or
spark.
Possible Cause
Corrective Action
a. Incorrect wiring.
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor
are connected to correct terminals on module and pilot assembly.
Reversed wires at the module may cause system to make sparking
noise, but spark may not be present at pilot hood.
b. Loose connections or electrical
shorts in the wiring.
Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Rod closest to pilot hood should be ignitor.
Verify connections underneath pilot assembly are tight; also verify
connections are not grounding out to metal chassis, pilot burner,
pilot enclosure, mesh screen if present, or any other metal object.
c. Ignitor gap is too large.
Verify gap of igniter to pilot hood. The gap should be approximately
.17 inch or 1/8 inch.
d. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
a. Transformer installed correctly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
b. A shorted or loose connection in wir- Remove and reinstall the wiring harness that plugs into module.
ing configuration or wiring harness.
Verify there is a tight fit. Verify pilot assembly wiring to module.
Remove and verify continuity of each wire in wiring harness.
3. Pilot lights but continues to spark, and
main burner will not ignite. (If the pilot continues to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
c. Improper wall switch wiring.
Verify that 110/VAC power is “ON” to junction box.
d. Module not grounded.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
e. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF Rocker switch or wall
switch in ON position. Hold ground wire about 3/16 inch away from
“I” terminal on module. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
a. A shorted or loose connection in
sensor rod.
Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight. Verify connections are
not grounding out to metal chassis, pilot burner, pilot enclosure or
screen if present, or any other metal object.
b. Poor flame rectification or contaminated sensor rod.
Verify that flame is engulfing sensor rod. If the pilot assembly does
not have a ground strap, consider installing one to increase flame
rectification. Verify correct pilot orifice is installed and inlet gas
specifications. Flame carries rectification current, not the gas. If
flame lifts from pilot hood, the circuit is broken. A wrong orifice or
too high an inlet pressure can cause pilot flame to lift. The sensor
rod may be contaminated. Clean sensor rod with emery cloth.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
67
Intellifire Ignition System - (continued)
Symptom
Possible Cause
3. (Continued) Pilot lights
but continues to spark,
and main burner will not
ignite. (If the pilot continues to spark after the pilot
flame has been lit, flame
rectification has not occurred.)
4. Pilot sparks, but Pilot
will not light.
68
Corrective Action
c. Module is not grounded.
Verify that module is securely grounded to metal chassis
of appliance. Verify that wire harness is firmly connected to
module.
d. Damaged pilot assembly or dirty sensor
rod.
Verify that ceramic insulator around the sensor rod is not
cracked, damaged, or loose. Verify connection from sensor rod to white sensor wire. Clean sensor rod with emery
cloth to remove any contaminants that may have accumulated on sensor rod. Verify continuity with a multimeter with
ohms set at lowest range.
e. Faulty module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire “I” from module. Place ON/OFF
Rocker switch or wall switch in ON position. Hold ground
wire about 3/16 inch away from “I” terminal on module. If
there is no spark at “I” terminal module must be replaced.
If there is a spark at “I” terminal, module is fine. Inspect
pilot assembly for shorted sparker wire or cracked insulator
around electrode.
a. Correct gas supply.
Verify that incoming gas line ball valve is “open”. Verify that
inlet pressure reading is within acceptable limits, inlet pressure must not exceed 14 in. W.C.
b. Ignitor gap is too large.
Verify that spark gap from ignitor to pilot hood is .17 in. or
1/8 in.
c. Module is not grounded.
Verify module is securely grounded to metal chassis of
appliance.
d. Module voltage output / Valve/Pilot
solenoid ohms readings.
Verify battery voltage is at least 2.7 volts. Replace batteries if voltage is below 2.7.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
15
Maintaining and Servicing Appliance
Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified
service technician should perform an appliance checkup at the beginning of each heating season.
WARNING
Risk of injury or property damage.
Before servicing:
• Turn off gas.
• Turn off electricity to appliance.
• Disable remote control, if one is present.
• Ensure appliance is completely cooled.
After servicing:
• Replace any screen or barrier that was removed.
• Reseal and reinstall any venting removed for servicing.
WARNING
Annual inspection by qualified technician recommended.
Check:
• Condition of doors, surrounds and fronts.
• Condition of glass, glass assembly and glass seal.
• Obstructions of combustion and ventilation air.
• Condition of logs.
• Condition of firebox.
• Burner ignition and operation.
• Burner air shutter adjustment
• Gas connections and fittings.
• Obstructions of termination cap.
CAUTION
Handle glass assembly with care.
NOTE: Clean glass after initial 3-4 hours operation.
Longer operation without cleaning glass may
cause a permanent white film on glass.
When cleaning glass door:
• Avoid striking, scratching or slamming glass.
• Do NOT use abrasive cleaners.
• Use a hard water deposit glass cleaner on white film.
• Do NOT clean glass when hot.
• Turn off appliance after 3-4 hours of operation and
ALLOW TO COOL.
• Remove and clean glass assembly.
• Replace glass assembly and operate appliance for
additional 12 hours.
Refer to maintenance instructions.
WARNING
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
• Combustible materials blocking cap may ignite.
• Restricted air flow affects burner operation.
Clean:
• Glass
• Air passageways, grilles,
control compartment
• Burner, burner ports
Risk of:
• Fire
• Delayed ignition or explosion
• Exposure to combustion fumes
• Odors
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
69
A. Maintenance Tasks
Inspect
Doors, Surrounds
and Fronts
Maintenance Tasks
1. Assess condition of screen and replace as necessary. Recommend addition of screen if one is not present.
2. Inspect for scratches, dents or other damage and repair as necessary.
3. Verify no obstructions to airflow through the louvers.
4. Verify maintenance of proper clearance to combustible household objects.
Gasket Seal, Glass
Assembly and Glass
1. Inspect gasket seal and its condition.
2. Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.
3. Confirm there is no damage to glass or glass frame. Replace as necessary.
4. Verify that latches engage properly, clip studs are not stripped, and glass attachment components are
intact and operating properly. Replace as necessary.
5. Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.
Valve Compartment
and Firebox Top
1. Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw
tips that have penetrated the sheet metal are sharp and should be avoided.
2. Remove any foreign objects.
3. Verify unobstructed air circulation.
Logs
1. Inspect for broken, damaged, or missing logs. Replace as necessary.
2. Verify correct log placement and no flame impingement causing sooting. Correct as necessary.
Firebox
1. Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.
2. Replace appliance if firebox has been perforated.
Burner Ignition and
Operation
1. Verify burner is properly secured and aligned with pilot or igniter.
2. Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.
3. Replace ember materials with new dime-size and shape pieces. Do not block ports or obstruct lighting paths.
4. Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.
5. Inspect for lifting or other flame problems.
6. Verify air shutter is clear of dust and debris.
7. Inspect orifice for soot, dirt or corrosion.
8. Verify manifold and inlet pressures. Adjust regulator as required.
9. Inspect pilot flame strength. Clean or replace orifice as necessary.
10. Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Clean with emery
cloth or replace as required.
11. Verify millivolt output. Replace as necessary.
Venting
1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.
2. Confirm that termination cap remains clear and unobstructed by plants, etc.
3. Verify that termination cap clearance to subsequent construction (building additions, decks, fences or
sheds) has been maintained.
4. Inspect for corrosion or separation.
5. Verify weather stripping, sealing and flashing remains intact.
6. Inspect draft shield to verify it is not bent, damaged or missing.
Remote controls
1. Verify operation of remote.
2. Replace batteries in remote transmitters and battery-powered receivers.
3. Verify batteries have been removed from battery back-up IPI systems to prevent premature battery failure
or leaking.
70
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
16
Reference Materials
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
O
N
P
M
Q
L
ØR
ØK
GAS LINE ACCESS
C
J
I
E
D
V
H
F
S
B
T
Location
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
SL-350TRS-IPI
Inches
Millimeters
33
838
28-1/8
714
24-1/8
613
16
406
29-1/8
740
3-1/2
90
6-7/8
175
21-3/8
543
32-3/8
822
34-1/2
877
8
203
8-3/4
223
16-1/4
413
1/2
13
22-3/4
578
11-3/8
289
15-7/8
403
6-5/8
168
2-1/8
54
6
153
1
25
28
712
A
SL-550TRS-E
Inches
Millimeters
36
913
31-1/8
791
27-3/16
691
18-1/16
459
31-1/8
790
3-9/16
90
6-7/8
174
23-3/8
593
34-3/8
873
36-7/16
926
8
203
8-13/16
223
16-5/16
415
1/2
13
25-3/4
653
12-7/8
326
15-7/8
403
6-5/8
168
2-3/16
55
6
152
1
25
30-1/16
764
U
G
ELECTRICAL
ACCESS
SL-750TRS-E
Inches
Millimeters
41
1041
36-1/8
917
32-1/16
815
21-1/2
547
34-5/8
879
3-9/16
90
6-7/8
174
26-7/8
683
37-7/8
962
39-15/16
1015
8
203
8-13/16
223
16-5/16
415
1/2
13
30-3/4
781
15-3/8
391
15-7/8
403
6-5/8
168
2-3/16
55
6
152
1
25
33-9/16
853
Figure 16.1 Appliance Dimensions
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
71
B. Vent Components Diagrams
Pipe
Effective
Height/Length
DVP Pipe (see chart)
DVP4
Effective Length
Inches
Millimeters
4
102
10-1/2 in.
(267 mm)
45 °
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
10-7/8 in.
(276 mm)
°
DVP45 (45 Elbow)
4-7/8 in.
( 276 mm)
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
DVP12MI 3 to 12
76 to 305
DVP24MI 3 to 24
76 to 610
11-3/8 in.
(289 mm)
10 in.
(254 mm)
10 in.
(254 mm)
1 in.
(25 mm)
7-3/8 in.
(187 mm)
24 in.
(610 mm)
1-1/4 in. (32 mm)
9-1/4 in.
(235 mm)
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
DVP-FS (Ceiling Firestop)
DVP-AS (Attic Shield)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
1 in.
(25 mm)
8 in.
(203 mm)
14 in.
(356 mm)
UP
5 in.
(127 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Support)
DVP-WS (Wall Shield Firestop)
Figure 16.2 DVP vent components
72
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-5/8 in.
Trap1
12 in.
(305 mm)
Max
Effective
Length
79 mm
117 mm
5-3/8 in.
9-3/8 in.
137 mm
238 mm
Trap2
DVP-TRAP
Horizontal Termination Cap
DVP-TRAP1
DVP-TRAP2
DVP-TRAPK1
DVP-TRAPK2
DVP-HPC1
DVP-HPC2
Figure 16.3 DVP vent components
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
73
B. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(367 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(127 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(367 mm)
RF6M
Roof Flashing Multi-pak
RF12M
Roof Flashing Multi-pak
5 in.
(127 mm)
13-3/4 in.
(349 mm)
11-7/8 in.
(302 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
BEK
Trap Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
DVP-TRAPFL
Flashing
DVP-HSM-B
Extended Heat Shield
Figure 16.4 DVP vent components
74
5 in.
(127 mm)
COOL-ADD
Cap Shield
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
14 in.
(356 mm)
DRC-RADIUS
Cap Shield
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
B. Vent Components Diagrams (continued)
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
3-7/8 in.
(98 mm)
17-3/4 in.
(451 mm)
14 in.
(356 mm)
10-1/2 in.
(267 mm)
DVP-TV
VerticalTermination Cap
12 in.
(305 mm)
DVP-TB1
BasementVent Cap
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
5-1/4 in.
(133 mm)
DVP-TVHW
VerticalTermination Cap (Highwind)
PVK-80
(For use with IPI and DSI appliances only.)
14 in.
(356 mm)
16-7/8 in.
(429 mm)
12 in.
(305 mm)
7-1/8 in.
(181 mm)
12-1/8 in.
(314 mm)
8-3/4 in.
(222 mm)
1-5/8 in.
(41 mm)
DVP-HPC
High Performance Cap
1 in.
(25 mm)
7-1/4 in.
(184 mm)
14 in.
(356 mm)
3/8 in. (10 mm)
1 in. (25 mm)
7-3/4 to 10-3/8 in.
(197 to 264 mm)
DVP-FBHT
FireBrickTermination Cap
Figure 16.5 DVP vent components
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
75
B. Vent Components Diagrams (continued)
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
8-3/8 in.
213 mm
5-1/2 in.
140 mm
87°
3°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
DVP-HRC-SS
DVP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
Figure 16.6 DVP vent components
WARNING
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZCSS termination caps on top vented fireplaces,
a one foot minimum vertical vent section is
required before installing first elbow.
• When using DVP-TB1 termination cap on top vented
fireplaces, a three foot minimum vertical vent section is
required before installing first elbow.
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
5-1/2 in.
140 mm
87°
8-3/8 in.
213 mm
3°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
SLP-HRC-SS
SLP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
DVP-TB1
SLP90
DVP-TB1
SL-2DVP
ASSEMBLY
Figure 16.7 SLP Series Vent Components
76
DVP-TB1
HORIZONTAL TERMINATION CAP
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
B. Vent Components Diagrams (continued)
6-1/2 in.
165 mm
6-1/2 in.
165 mm
6-1/2 in.
165 mm
8-3/4 in.
222 mm
6 in.
152 mm
9-1/4 in.
235 mm
6-5/8 in.
168 mm
6-5/8 in.
168 mm
9-7/8 in.
251 mm
SLP45
45° Elbow
SLP90
90° Elbow
Effective Height/Length
Effective
Height/
Length
SLP-PIPE
Pipe
inches
mm
SLP4
4
102
SLP6
6
152
SLP12
12
305
SLP24
24
610
SLP36
36
914
SLP48
48
1219
SLP6A
2-6
51 - 152
SLP12A
2 - 12
51 - 305
SLP-FLEX-2
24
610
SLP-FLEX-3
36
914
SLP-FLEX-5
60
1524
SLP-FLEX-10
120
3048
EFFECTIVE HEIGHT/
LENGTH
SLP-FLEX-PIPE
26 in.
660 mm
DVP-HSM-B
Extended Heat Shield
SLP-HVS
Horizontal Pipe
Support
RF4-8
Roof Flashing
SLP-FS
Ceiling Firestop
SLP-WS
Wall Shield Firestop
Figure 16.8 SLP Series Vent Components
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
77
B. Vent Components Diagrams (continued)
SLP-DCF-BK
Ceiling Firestop
Black
SLP-TRAP2
Horizontal
Termination Cap
SLP-TRAP1
Horizontal
Termination Cap
SLP-TVHW
Vertical
Termination Cap
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
SLP-SNKD
Snorkel
Termination Cap
PVK-80
(For use with IPI and DSI appliances only.)
SL-2DVP
Adapter
SLP-WT-BK
Wall Thimble-Black
DVP-FBHT
SLP90
SL-2DVP
SLP-FLEX-TRAP
Horizontal
Termination Kit
Figure 16.9 SLP Series Vent Components
78
ASSEMBLY
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
DVP-FBHT
SL-350TRS-IPI
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
Service Parts Diagram
5
7
6
8
Log Set Assembly
3
2
1
4
Part number list on following page.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
79
C. Service Parts List
SL-350TRS-IPI
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-350TRS-D
Y
1
Log 1
SRV2113-701
2
Log 2
SRV2113-702
3
Log 3
SRV2113-704
4
Log 4
SRV2113-703
5
Burner Assembly
2113-007
6
Base Pan/Grate Assembly
2113-015
7
Glass Door Assembly
GLA-3504TRS
Y
8
Junction Box
4021-013
Y
Exhaust Restrictor
530-299
Y
Gasket Assembly
Contains Burner neck, shutter bracket, vent, seal cap,
valve plate, and air passage gaskets
2113-080
Glass Latch Assembly
386-122A
Lava Rock
060-721
Mineral Wool
050-721
Non-combustible Board
539-401
Pilot Tube
SRV485-301
Touch Up Paint
203-9
Conversion Kit NG
N/A
Conversion Kit LP
LPK-350TRS-IPI
Y
Pilot Orifice NG
593-528
Y
Pilot Orifice LP
593-527
Y
Regulator NG
NGK-DXV
Y
Regulator LP
LPK-DXV
Y
Additional service part numbers appear on following page.
80
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
Y
Y
SL-350TRS-IPI
Service Parts
Valve Assembly Parts List
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
1
IPI Valve Assembly
2
10
11
3
9
8
12
4
5
6
7
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Pilot Assembly NG
2090-012
Y
Pilot Assembly LP
2090-013
Y
2
Shutter Bracket Assembly
2118-121
Y
3
Battery Pack
593-594A
Y
4
Flex Tube Assembly
7000-156
Y
5
3 Volt Transformer
593-593A
Y
6
Module Wire Assembly
593-590A
Y
7
Thermostat Wire Assembly
2118-170
Y
8
Module
593-592
Y
Valve NG
750-500
Y
Valve LP
750-501
Y
10
Flex Ball Valve Assembly
302-320A
Y
11
Valve Bracket
2118-104
Orifice NG (#44)
582-844
Y
Orifice LP (#55)
582-855
Y
1
9
12
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
81
Service Parts
SL-550TRS-E, SL-550TRS-IPI-E
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
Service Parts Diagram
10
8
7
11
12
14
13
9
6
Log Set Assembly
2
5
3
4
1
Part number list on following page.
82
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
Service Parts List
SL-550TRS-E, SL-550TRS-IPI-E
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts
listed in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-550TRS-D
1
Log 1
SRV2065-701
2
Log 2
SRV2065-702
3
Log 3
SRV2065-703
4
Log 4
SRV2065-704
5
Log 5
SRV2065-705
Refractory Kit
Y
BRICK-550TRSD2
6
Refractory, Right Side
SRV2044-712
7
Refractory, Back
SRV2044-711
8
Refractory, Left Side
SRV2044-710
9
Junction Box
4021-013
10
Pilot shield
2066-121
Burner NG
SRV2066-020
Y
Burner LP
SRV2066-021
Y
12
Base Pan
2065-100
13
Log Grate
2066-036
14
Glass Door Assembly
GLA-550TRS
Exhaust Restrictor
530-299
11
Y
Y
Gasket Assembly
Contains Burner neck, shutter bracket, vent, seal cap, valve
plate, and air passage gaskets
Î
2115-080
Glass Latch Assembly
386-122A
Mineral Wool
050-721
Non-combustible Board
547-401
Pilot Tube
SRV485-301
Touch up Paint
203-9
Vermiculite Embers
MYSTIC-EMBERS
Y
Y
STANDING PILOT CONVERSION KITS
Conversion Kit NG
NGKS-550TRSE
Y
Conversion Kit LP
LPKS-550TRSE
Y
Pilot Orifice NG
2103-116
Y
Pilot Orifice LP
2103-117
Y
Regulator NG
230-1570
Y
230-1520
Y
Conversion Kit NG
NGK-550TRS-IPIE
Y
Conversion Kit LP
LPK-550TRS-IPIE
Y
Pilot Orifice NG
593-528
Y
Pilot Orifice LP
593-527
Y
Regulator NG
NGK-DXF
Y
Regulator LP
LPK-DXF
Y
Regulator LP
IPI CONVERSION KITS
Additional service part numbers appear on following page.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
83
SL-750TRS-E, SL-750TRS-IPI-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
Service Parts Diagram
10
8
7
11
14
12
13
6
9
Log Set Assembly
2
5
4
3
1
Part number list on following page.
84
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
Service Parts List
SL-750TRS-E, SL-750TRS-IPI-E
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located
on your dealers' VIP site. When ordering, supply serial and model numbers to ensure
correct service parts.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-750TRS-D
1
Log 1
SRV2065-701
2
Log 2
SRV2066-702
3
Log 3
SRV2066-703
4
Log 4
SRV2066-704
5
Log 5
SRV2066-705
Refractory Kit
BRICK-750TRSD2
6
Refractory, Right Side
SRV2045-712
7
Refractory, Back
SRV2045-711
8
Refractory, Left Side
SRV2045-710
Y
9
Junction Box
4021-013
10
Pilot Shield
2066-121
Burner NG
SRV2066-020
Y
Burner LP
SRV2066-021
Y
12
Base Pan
2066-100
13
Log Grate
2066-036
14
Glass Door Assembly
GLA-750TRS
Exhaust Restrictor
530-299
11
Y
Y
Gasket Assembly
Contains Burner neck, shutter bracket, vent, seal cap, valve
plate, and air passage gaskets
Î
2118-080
Glass Latch Assembly
386-122A
Mineral Wool
050-721
Non-combustible Board
534-401
Touch up Paint
203-9
Vermiculite Embers
MYSTIC-EMBERS
Y
IPI CONVERSION KITS
Conversion Kit NG
NGKS-750TRSE
Y
Conversion Kit LP
LPKS-750TRSE
Y
Pilot Orifice NG
2103-116
Y
Pilot Orifice LP
2103-117
Y
Regulator NG
230-1570
Y
230-1520
Y
Conversion Kit NG
NGK-750TRS-IPIE
Y
Conversion Kit LP
LPK-750TRS-IPIE
Y
Pilot Orifice NG
593-528
Y
Pilot Orifice LP
593-527
Y
Regulator NG
NGK-DXV
Y
Regulator LP
LPK-DXV
Y
Regulator LP
IPI CONVERSION KITS
Additional service part numbers appear on following page.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
85
SL-550TRS-IPI-E, SL-750TRS-IPI-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
Valve Assembly Parts List
1
IPI Valve Assembly
11
2
3
10
9
8
4
5
7
6
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
1
DESCRIPTION
2090-012
Y
Pilot Assembly LP
2090-013
Y
582-840
Y
582-583
Y
582-837
Y
Orifice LP (#53C)
Orifice NG (#37C)
SL-550TRS-IPI-E
SL-750TRS-IPI-E
582-852
Y
3
Battery Pack
593-594A
Y
4
Flexible Gas Connector
530-302A
Y
5
3 Volt Transformer
593-593A
Y
6
Wire Assembly
593-590A
Y
7
Module
593-592
Y
Valve NG
750-500
Y
Valve LP
750-501
Y
9
Thermostat Wire Assembly
2118-170
Y
10
Flex Ball Valve Assembly
302-320A
Y
11
Valve Bracket
2118-104
Orifice LP (#52C)
8
86
PART NUMBER
Pilot Assembly NG
Orifice NG (#40C)
2
COMMENTS
Stocked
at Depot
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
SL-550TRS-E, SL-750TRS-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: ______
Valve Assembly Parts List
1
Standing Pilot
Valve Assembly
3
2
8
4
5
7
6
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your
appliance please provide model number and serial number. All parts listed in this manual may be ordered
from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked at
Depot
PART NUMBER
Pilot Assembly NG
2103-010
Y
Pilot Assembly LP
2103-011
Y
2
Valve Bracket
2118-104
3
Flex Ball Valve Assembly
302-320A
Y
Valve NG
230-0710
Y
Valve LP
230-0720
Y
5
Piezo Ignitor
291-513
Y
6
Thermostat Wire Assembly
2045-024
Y
7
Flexible Gas Connector
530-302A
Y
Orifice NG (#40C)
582-840
Y
582-853
Y
582-837
Y
582-852
Y
1
4
8
Orifice LP (#53C)
Orifice NG (#37C)
Orifice LP (#52C)
SL-550TRS-E
SL-750TRS-E
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
87
C. Limited Lifetime Warranty
Hearth & Home Technologies LIMITED WARRANTY
Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet
and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada.
Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Components Covered
Gas
Wood
Pellet
EPA
Wood
Electric
Venting
X
X
X
X
X
X
X
X
Igniters, Electronic Components,
and Glass
X
X
Blowers
X
X
All Parts and Material Except as
covered by Conditions, Exclusion,
and Limitations listed
X
3 years
Molded Refractory Panels
X
Firepots
5 years
3 years
7 years
3 years
10 years
1 year
X
Burners, Logs & Refractory
Limited
Lifetime
1 year
X
Firebox & Heat Exchanger
90 Days
X
X
X
X
X
Castings & Baffles
X
X
Firebox, HHT Chimney,
Termination & Heat
Exchanger
X
X
X
See Conditions, Exclusions, and limitations.
X
All Replacement Parts
9-01-08
CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY
• This warranty applies to the original owner and is transferable up to two years from date of purchase to the new homeowner,
provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its
original place of installation.
• The maximum amount recoverable under this warranty is limited to the purchase price of the product.
• In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.
• Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home is
not covered under this warranty.
Page 1 of 2
88
4021-645A 09-01-08
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
D. Limited Lifetime Warranty (continued)
• This limited warranty does not extend to or include surface finish on the appliance or terminations, door gasketing, glass
gasketing, glass discoloration, firebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion
on any of the metal surfaces, cast iron components, baffles, firepots, doors, or firebox area are not covered by this
warranty.
• Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to this
noise are not covered by this warranty.
• HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or maintenance
of the appliance not in accordance with the installation instructions; operating instructions and the listing agent identification
label furnished with the appliance; (2) installation which does not comply with local building codes; (3) shipping, improper
handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate
ventilation or drafting caused by tight sealing construction of the structure or handling devices such as exhaust fans or forced
air furnaces or other such causes; (5) use of fuels other than those specified in the operating instructions; (6) installation
or use of components not supplied with the appliance or any other components not expressly authorized and approved
by HHT; and/or (7) modification of the appliance not expressly authorized and approved by HHT in writing.
• This warranty does not apply to non-HHT venting components, hearth components or other accessories used in conjunction
with the installation of this product.
• This warranty is void if the appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine,
or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or there is any
damage to the appliance or other components due to water or weather damage which is the result of, but not limited to,
improper chimney or venting installation.
• HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship during
the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the defective
component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.
• Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not
apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state.
• EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE
WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF
THE WARRANTY SPECIFIED ABOVE.
This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all
warranties currently in existence.
If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide necessary
parts or components, contact the nearest authorized HHT dealer or supplier.
Page 2 of 2
4021-645A 09-01-08
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
89
E. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471,
5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195,
6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426,
6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia)
780250, 780403, 1418504 or other U.S. and foreign patents pending.
Printed in U.S.A. - Copyright 2008
90
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. F • 9/08
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising