OWNERS MANUAL WARNING: TO PREVENT ELECTRICAL SHOCK OR FIRE HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. BEFORE USING THIS APPLIANCE, READ THE OPERATING GUIDE FOR FURTHER WARNINGS. ли — "avis. ==— CHORUS/ EFFECTS PE ТЕН INFUTS 0% PATCH РАГСН PHONES a O: LAN GAIN Eli i SEND RETURN Sin a ! a 1 2 4 3 5 6 7 8 9 10 Tn 12 13 14 FRONT PANEL HIGH GAIN INPUT (1) Used for most electric guitars. It is 6 dB louder than the Low Gain input. LOW GAIN INPUT (2) Provided for instruments that have extremely high outputs, which can result in overdriving (distorting) the High Gain input. If both inputs are used simultaneously, the output levels are the same (both are Low Gain). BRIGHT SWITCH (3) Provides a preset boost (+ 8 dB) to treble frequencies. To activate, depress the switch to its “in” position. PRE GAIN (4) Controls the input volume level of the amplifier. POST GAIN (5) Controls the overall volume level of the amplifier. The final level adjustment should be made after the desired sound has been achieved. LOW (6) An active tone control (shelving type, +/- 15 dB) that varies the low frequency boost or cut. OPERATION NOTE Excessive EQ boost, especially of the low frequencies, increases the possibility of speaker damage, and sacrifices valuable heacroom. GRAPHIC EQUALIZER (7) This seven-band, one octave equalizer provides 15 dB of boost or cut at each center frequency. HIGH (8) An active tone control (shelving type +/- 15 dB) that varies the high frequency boost or cut. CHORUS EFFECTS SEND (9) High pass output above 200 Hz for supplying signals to external effects or signal processing equipment. EFFECTS RETURN (10) Provided for patching an effects device output back into the mixer, May also be used as an independently variable auxiliary input. PREAMP OUT/POWER IN (11) These jacks are provided for in-line patching of effects devices. To patch an effects unit, connect the Preamp Qutput to the Input of the device. Next, connect the output of the device to the Power Amp Input (high-quality shielded cables must be used for these connections). The Preamp Output can also be used to route the amplified signal to a mixing console, tape recorder, etc. Connectthe Preamp Output, using a shielded cable, to an input of the tape recorder, mixer, etc. This patch does not affect the operation of the amplifier. NOTE: The preamp output level is approximately 1 volt RMS and is of relatively low impedance (600 ohms). Any effects device used in this effects loop must be capable of receiving 1 volt input and providing 1 volt output in order to properly drive the power amp. The Power Amp Input has an internal switch which disconnects the internal preamp. HEADPHONE JACK (12) This stereo jack allows signals to flow to both sides of any stereo headset. POWER LED (13) Iluminates when AC power is being supplied to the amp. POWER SWITCH (14) Depress to “Cn” position to turn on. BLOCK DIAGRAM CHORUS EFFECTS PATCH RETURH TKO 75 AMP GAIN GAIN PRE. PRE HIGH INPUT LOW INPUT PHISH BRIGHT PUNCH ACTIVE L CY HIGH ACTIVE 7 BAND EO IIA ACTIVE GH FAS PRE Fr AMP ama DUT Li | y ! VAmSs ¡0 dE CHORUS EFFECTS PATCH SEMO This block diagram shows signal flow within the unit, In order lo throughly undarstand the unit's functions, please study the block diagram carefully. BACK PANEL GND. "AS Ta A PRODUCT OF PEAVEY ELECTRONICS SORE. 215 Y RS MERIDIAN, MS MADE IN US. 6 2 120 VA TKO ты 75 eros EEE а "ные BUILT UNDER LS PATENT BO. 4310053 BO He A В! A E sr FwH РОО МАТЫ | АЙ map on ESTE лы La AIH LEMA HSH сан ur Pan Lu CAUTION пари Pre mas al] liberia 10 PREVENT THE AISK OF FIRE AMD SHOCK om 19 ян) aus HAZARD. DO NOT EXPOSE THES APELIANCE oth Line TC RAIN OF MOISTU MOVE C=] = FROM CèSE, HO USER EFAVICEABLE PARTE pan FUHCH IMSIDE. REFER SERWICINS TO QUALIFIED SERVICE PERSONNEL E FETCH LEH AVIS: RISQUE DE CHOC ELECTRIQUE - NE ACTIVE TS CLARA ван LINE (MAINS) CORD RETAINER (15) Allows storage of mains cable for travel. GROUND SWITCH (16) Three position rocker-type switch which, in most applications, should be operated in its center or zero position. There may be some situations when audible hum and/or noise will come from the loudspeaker. If this situation arises, position the ground switch to either positive or negative (+ or -) or until the noise is minimized. NOTE: Should the noise problem continue, consult your Authorized Peavey Dealer, the Peavey Factory, or a qualified service technician. THE GROUND SWITCH IS NOT FUNCTIONAL ON 220/240 VOLT MODELS. LINE CORD (120 V PRODUCTS ONLY) (17) For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is not advisable to remove the ground pin under any circumstances. If it is necessary to use the equipment without proper grounding facilities, suitable grounding adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles. TONE SETTING CHART "IN" ROCK — GAN — EQUALIZATION A: ana er EA Lgl 3 7 (9 3 ? E E Ea 5 E B q В 2 В 19 9 E E-E- E 9 5 1 a 1 я |718 ig ih ml a mm 12 te О 10 0 to -15 15+ Warm — ——"—— — AA —15 15+ ARE POST Low > 120 00 20 660 зако FÉ бк - HG "IN" FUNK — GAIN de A PO a 3.0 = = A Eu 3 ” A) 7? 5 5 5. == == т : 0 — a ' q 1 a E ЦЕ Fm ee п == ше — aa ü 10 “15 + 15- == Emme SE PAE POST LOW > 120 165 140 560 13% 28ER SE ~ HIGH Lh по L x a au 2 cn LT 1515 "OUT" COUNTRY — A] EQUALIZATION — — — — — — = 4 E Ro. 4 = E 3 J = vw Pa al ei Leroy e =13 Ca 0 EE O ? 8 2 TE 2 BR S EE: 7 5 | 8 sq € RA — о! Е a vo С 10 HE 1954 1% 15 — 15. PSE Ze —— =m — —_— — — E POET LOW > зао зао 340 660 13H fe GK HIGH Tone settings given are general and will vary according to type of guitar, type and gauges of strings, type of pickup and even tvpe of pick, Personal taste, playing style, anc type of music greatly coninbule to desired tonality. THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SUBJECT TO WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY. Ces clauses de garantie ne sont vaiables qu'aux Etats-Unis et au Canada. Dans tous les autres pays, les clauses de garantie et de maintenance sont fixées parle distributeur nationalet assuree par lul seion la legislation en vigueur. Diese Garantie ist nur in den USA and Kanada gultig. Alle Export-Produkie sind der Garantie und dem Service des Importeurs des jewelligen Landes unterworfen. Esta garantia es valida solamente cuando el producto es comprado en E.U. continentales o en Canada. Todos los productos que sean comprados en el extranjero, estan sujetos alas garantias y servicio que cada distribuidor autorizado determine y ofrezca en los diferentes paises. ONE-YEAR LIMITED WARRANTY/REMEDY PEAVEY ELECTRONICS CORPORATION (“PEAVEY') warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in material and workmanship for a period of one (1) year from date of purchase, PROVIDED, however that this limited warranty is extended only to the original retail purchaser and is subject to the conditions, exclusions and limitations hereinafter set forth; PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanship for a period of ninety (80) days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is also subject to the conditions, exclusions and limitations hereinafter set forth. CONDITIONS, EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES These limited warranties shall be void and of no effect if: a. The first purchase of the product is for the purpose of resale; or b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER; or e. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not arising oul of defects in material or workmanship; or d. The serial number affixed to the product is altered, defaced or removed. In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will: a. In the case of tubes or meters, replace the defective component without charge; b. In other covered cases (i.e. cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect in material or workmanship or replace the product, at Peavey's option; and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the purchaser. THEWARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) DAYS FROMTHE DATE OF YOUR PURCHASE. In order to obtain service under these warranties, you must: a. Bring the defective item to any AUTHORIZED PEAVEY DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product. If the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest other PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER which can provide such service. OR b. Ship the defective item, prepaid, to: PEAVEY ELECTRONICS CORPORATION International Service Center Highway 80 East MERIDIAN, MS 39301 including therewith a complete, detailed description of the problem, together with a legible copy of the original PROOF OF PURCHASE and a complete return address. Upon Peavey's receipt of these items: If the defect is remedial under these limited warranties and the other terms and conditions expressed herein have been complied with, Peavey will provide the necessary warranty service to repair or replace the product and will return it, FREIGHT COLLECT, to you, the purchaser. Peavey's liability to the purchaser for damages from any cause whatsoever and regardless of the form of action, including negligence, is limited to the actual damages up to the greater of $500.00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly related to the cause of action. Such purchase price will be that in effect for the specific product when the cause of action arose. This limitation of liability will not apply to claims for personal injury or damage to real property or tangible personal property allegedly caused by Peavey's negligence. Peavey does not assume liability for personal injury or property damage arising out of or caused by a non-Peavey alteration or attachment, nor does Peavey assume any responsibility for damage to interconnected non-Peavey equipment that may result from the normal functioning and maintenance of the Peavey equipment. UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, ANY INCIDENTAL DAMAGES OR ANY CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE; PROVIDED, HOWEVER, THAT IF THE OTHER TERMS AND CONDITIONS NECESSARY TO THE EXISTENCE OF THE EXPRESS, LIMITED WARRANTIES, AS HEREINABOVE STATED, HAVE BEEN COMPLIED WITH, IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE APPLICABLE ONE-YEAR OR NINETY-DAY PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT. SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG ANIMPLIED WARRANTY LASTS, ORTHE EXCLUSION OR LIMITATION OF INCIDENTAL COR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THESE LIMITED WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE. THESE LIMITED WARRANTIES ARE THE ONLY EXPRESS WARRANTIES ON THIS PRODUCT, AND NO OTHER STATEMENT, REPRESENTATION, WARRANTY OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY, In the event of any modification or disclaimer of express or implied warranties, or any limitation of remedies, contained herein conflicts with applicable law, then such modification, disclaimer or limitation, as the case may be, shall be deemed to be modified to the extent necessary to comply with such law. Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty only with respect to equipment purchased in the United States of America. INSTRUCTIONS — WARRANTY REGISTRATION CARD 1. Mail the completed WARRANTY REGISTRATION CARD to; PEAVEY ELECTRONICS CORPORATION POST OFFICE BOX 2898 MERIDIAN, MISSISSIPPI 39302-2898 a. Keep the PROOF OF PURCHASE. In the event warranty service is required during the warranty period, you will need this document. There will be no identification card issued by Peavey Electronics Corporation. 2. IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESS: a. Completion and mailing of WARRANTY REGISTRATION CARDS — Should notification become necessary for any condition that may require correction, the REGISTRATION CARD will help ensure that you are contacted and properly notified. b. Notice of address changes — If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of the change of address so as to facilitate your receipt of any bulletins or other forms of notification which may become necessary in connection with any condition that may require dissemination of information or correction, 3. You may contact Peavey directly by telephoning (601) 483-5365. 4. Please have the Peavey product name and serial number available when communicating with Peavey Customer Service. TKO ® 75 SPECIFICATIONS: POWER AMPLIFIER SECTION: RATED POWER & LOAD: 75 W RMS into 8 ohms with DDT™ compression POWER @ CLIPPING: (TYPICALLY) (1 kHz, 120 VAC line) 76 W RMS into 8 ohms @ 1% THD 84 W RMS into 8 ohms @ 5% THD FREQUENCY RESPONSE: +0, -2 dB, 20 Hz to 30 kHz @ 70 W RMS into 8 ohms TOTAL HARMONIC DISTORTION: Less than 0.2%, 100 mW to 70 W RMS, 20 Hz to 10 kHz, 8 ohms, typically below 0.1% DOT" DYNAMIC RANGE: Greater than 20 dB DDT" MAXIMUM THD: Below 0.5% THD for 6 dB overload Below 1% THD for 16 dB overload HUM & NOISE: Greater than 90 dB below rated power POWER CONSUMPTION: (Domestic) 200 watts @ 120 VAC, 50/60 Hz PREAMP SECTION: The following specs are measured @ 1 kHz with the Low, High & Graphic EQ @ 0 dB; Push Bright out (off); and Post Gain @ 10. Nominal levels are with Pre Gain @ 5; minimum levels are with Pre Gain @ 10. PREAMP HIGH GAIN INPUT: Impedance: High £, 220K ohms Nominal Input Level: -20 dBV, 100 mV RMS Minimum Input Level: -40 dBY, 10 my AMS Maximum Input Level: +10 dBY, 3 Y RMS PREAMP LOW GAIN INPUT: Impedance: High Z, 44K ohms Nominal Input Level: -14 dBV, 200 mV RMS Minimum Input Level: -34 dBV, 20 mY RMS Maximum Input Level: +16 dBY, 6 Y RMS EFFECTS PATCH SEND: (High Pass Output) Load Impedance: 10K ohms or greater Nominal Output Level: -12 dBV, 0.25 V RMS Maximum Output Level: +8 dBY, 2.5 Y RMS EFFECTS PATCH RETURN: Impedance: High £, 22K ohms Designed Input Level: -12 dBV, 0.25 V RMS (Remixes with Main Full Range Signal, designed for Low Level chorus or flange) PREAMP OUTPUT: Load Impedance: 1K ohms or greater Nominal Output Level: 0 dBY, 1 Y RMS (At the DDT limit of 75 W RMS Output) Maximum Output Level: +18 dBV, 8 V RMS POWER AMP INPUT: Impedance: High Z, 22K ohms Designed Input Level: 0 dBV, 1 Y RMS (Switching jack providing preamp output to power amp input connection when not used) HEADPHONE OUTPUT: Load Impedance: 4 ohms or greater Nominal power output: 100 mW into 4 ohms (Stereo jack, monaural signal, disconnects internal speaker when phone plug is inserted) SYSTEM HUM & NOISE @ NOMINAL INPUT LEVEL: (20 Hz to 20 kHz unweighted) 85 dB below rated power EQUALIZATION: Low & High: +-15 dB @ 80 Hz & 8 kHz, shelving 7 Band Graphic: +-15 dB @ 120, 180, 340, 660, 1.3K, 2.6K, 5K, PEAK/NOTCH Push Bright: +8 dB @ 2 kHz Punch: Preset Special EQ DURATION PER DAY IN HOURS ä 6 à 3 € 17 1 DANGER EXPOSURE TO EXTREMELY HIGH NOISE LEVELS MAY CAUSE A PERMANENT HEARING LOSS. INDIVIDUALS VARY CONSIDERABLY IN SUSCEPTIBILITY TO NOISE INDUCED HEARING LOSS, BUT NEARLY EVERYONE WILL LOSE SOME HEARING IF EXPOSED TO SUFFICIENTLY INTENSE NOISE FOR A SUFFICIENT TIME THE US GOVERNMENT'S OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) HAS SPECIFIED THE FOLLOWING PERMISSIBLE NOISE LEVEL EXPOSURES: SOUND LEVEL dBA, SLOW RESPONSE = ACCORDING то E ANY EXPOSURE N. EXCESS OF THE ABOVE PER MISSIBLE LIMIT 5 cou LD den SOME HEARING LOSS FEAR PLIFHE&TION SYSTE МУН o 8! HS o ANGERS EXPO MUST BE W SURE AGAI ha UNO PRESSE MAES OR OVER THE ETO HIGH DEE SIGNALIE E AY STRONG: ón = E —i AL PEAK POWER, ADEQUATÉEES D DAMAGE THE ASSOCIATE . Obey all cautions in the operating instructions and on the back of the url. - All operating instructions should be followed. This product should not be used near waler. ie a bathiub. sink. swimming pool, wét baseément, etc. This product should be located so that its position does nol interfere with its proper ventilation. 1 should not be placed flat against a wall or placed in a built-in enclosure thal will impede the flow of Cooling air, . This product should not be placed near a source of heat such as a stove, radiator or another heat producing amplifier. ee DE ADÉQUATE BOWER RESERVES CESIGNE HIS SYSTEME : ASE BE sr MAXIMUM re i thie pe marked dé вона power sup y а MON Ihe ground pin ав РОМ! su ply i “information on a write for our free booklel “Shock Hazard and Grounding.” Power supply cords should always be handled carefully Mever walk or place equipment on power supply cords Periodically check cards for culs or signs of siress, especially at the plug and the point where the cord exits the unit The power supply cord should be unplugged when Lhe unit is 10 be unused for long periods of time. If this praduct is 1o be mounted in an equipment rack, rear support should be provided 14. 15. Ра: should be taken so that objects do not fall and liquids are not spilled into the unit tArough the ventilation holes orány other operings. This unl should be checked By a Qualited service techrician if A. The power supply cord or plug has been damaged B. Anything has fallen or been spilled into the unit C. The unil does nat operate correctly CO. The unit has been dropped or the enclosure damaged . The user should not to altempt to service this equipment All service work should be done by a qualified service technician Features and specifications subject to change without notice. Peavey Electronics Corporation / 711 A Street / Meridian, MS 39302-2898 / U.S.A. / (601) 483-5365 Telex: 504115 / Fax: 484-4278 ©1988 Printed in the U.S.A. #80300754 12/88
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021