the Manual
quadrone
Instruction Manual
Accessories List
Upper Cover
of Casing
Lower Cover
of Casing
Circuit Board
Landing Feet
Carbon Fiber
Spindle
Lithium Battery
Propellers
Bearing
Red and Blue
Line Motor
Black and White
Reverse Motor
Green Light
Red Light
Tail Light
Panel
Bearing
1
Standard Accessories
Charger x1
3.7V 730 mAh
Li-po Battery x1
Propellers x4
Packing List
No
Part Name
Quantity
1
Instruction Manual
1
2
Quadcopter
1
3
Charger
1
4
Li-po Battery
1
5
Propellers
4
6
Remote Control
1
Upgradeable Accessories (Optional)
Water Shooter
5.8G FPV
Camera
WIFI FPV
Bubble Shooter
WIFI FPV
5.8G FPV
2
Notice
• All instructions, warranties and other collateral documents are subject
to change at the sole discretion of our company.
Warnings
• Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property or cause
serious injury. This is a sophisticated hobby product. It must be operated
with caution and common sense, and requires some basic mechanical
ability. Failure to operate this product in a safe and responsible manner
could result in injury or damage to the product or property. This product is
not intended for use by children without direct adult supervision. This
manual contains instructions for safety, operation and maintenance. It is
essential to read and follow all the instructions and warnings in this
manual, prior to assembly, set up or use, in order to operate correctly
and avoid damage or serious injury.
Additional Warnings and Precautions
1. Age Recommendation: Not for children under 14 years of age. This is
not a toy.
2. Always operate in open spaces away from obstacles, people, and
hazards.
3. Always follow directions and warnings for this and any optional
equipment carefully. (chargers, rechargeable battery packs, etc)
4. Always keep small parts and electrical parts out of the reach of
children.
5. Always avoid water exposure to all equipment not specifically
designed and protected for this purpose. Moisture can cause damage
to electronics.
6. Never place any portion of the model in your mouth as it could cause
serious injury or even death.
7. Never operate your model with low transmitter batteries.
3
Introduction
• Thank you for choosing Quadrone! This is a four-axis aircraft that can
fly outdoors, in order to make it easier to control the aircraft. Please
carefully read this manual before operating your Quadrone. Please keep
this manual for future reference.
• Before your first flight, please take the time to carefully read this manual
containing important flight information which will help your first flight go
more smoothly.
Table of Contents
Accessories List
Standard Accessories
Packing List
Notice
Warning
Additional Warnings and Precautions
Introduction
Table of Contents
Battery Usage and Warnings
Charging the Battery
First Flight Preparation
Syncing the Quad and Remote
Remote Diagram
360 Degree Flips
One Key Return
CF Mode
CF Mode X-axis Y-axis Calibration
Troubleshooting
Circuit Board Schematic
Exploded View
Parts List
Aircraft Parameters
4
1
2
2
3
3
3
4
4
5
6
6
7
8
9
10
10
10
10
11
12
13
13
Battery Usage and Warnings
CAUTION
Always use a
charger compatible
with batteries.
WARNING
Always charge
batteries away from
flammable materials.
WARNING
WARNING
Never leave
charging batteries
unattended.
Never charge
damaged batteries.
WARNING
Never alter
batteries.
WARNING
Never touch or use
hot batteries.
The battery charger included with your Quadrone has been designed to
safely charge your Li-po battery.
CAUTION: All instructions and warnings must be followed exactly.
Mishandling of Li-po batteries can result in fire, personal injury, and/or
property damage.
1. By handling, charging, or using the included Li-po battery you assume
all risks associated with lithium batteries.
2. If at any time the battery begins to balloon or swell, discontinue use
immediately. If charging, discontinue and disconnect. Continued use
or charging of a ballooning or swelling battery can result in fire.
3. Always store battery in dry, room temperature area.
4. Always transport or temporarily store the battery in a temperature
range of 40-120 degrees F. Do not store battery or model in a car or
direct sunlight. If stored in a hot car, the battery can be damaged or
even catch fire.
5. Never use a Ni-CD or Ni-MH charger. Failure to charge the battery
with a compatible charger may cause fire resulting in personal injury
and/or property damage.
6. Never exceed the recommended charge rate.
7. Never cover warning labels with hook and loop strips.
WARNING: Only use the charger supplied with your Quadrone. Do not
use 12V power supply or property damage and injury can
occur.
Notice: When a Li-po battery is discharged below 3.7V, the battery may
be damaged and may no longer accept a charge. Please land the
quadcopter immediately and recharge the battery.
5
Charging the Battery
Only use charger provided. Attach Li-po battery to charging line of
charger. Plug charger into power outlet. LED light should light up to
indicate it is charging.
Charging cable
LED
3.7V 730mAh
First Flight Preparation
1. Make sure the battery is fully charged.
2. When turning on the remotes power switch, make sure the throttle
stick is at the bottom in its lowest position.
3. Make sure to fly in an open area away from crowds, cars, trees, and
other obstacles to avoid damage to your quadcopter.
6
Syncing the Quad and the Remote
Step 1
Place the quadcopter on a flat
surface and place the Li-po battery
into the quadcopter. Plug the
battery into the quad and the LED
lights will begin to flash.
Step 2
Turn the remote controller on. Push
the throttle stick to its lowest
position. The quad will beep and
the lights will stop flashing. Your
quad and remote are now synced
together.
CAUTION
Push the throttle sick to
the lowest position.
Step 3
After your flight, remove the battery
from the quadcopter. Do this to
avoid power leakage and overall
damage to your quad and battery.
Step 4
Turn off your remote controller. If it
will not be used for a long duration
of time, remove batteries to prevent
power leakage and overall damage
to your remote controller.
If the remote control is not to be
used for a long duration, please
remove the batteries for storage.
7
Remote Diagram
Power Switch
LED Light
Antenna
360 Degree Flips
Camera
Direction Control Stick
Ascending/Descending
Forwards and
Backwards Trim
Speed Trim
Directional Trim
Sideways Trim
40% Flying Speed
X-Axis Calibration
100% Flying Speed
60% Flying Speed
Y-Axis Calibration
One Key Return
Take Photo
(Hold 2 Seconds
for Headless Mode)
80% Flying Speed
LCD Display
Bold = In Headless Mode
LCD Display
Stick Mode
Indicator
Battery Level
Stick Mode
Indicator
Speed Trim
Indicator
Directional Trim
Indicator
Sideway Trim
Indicator
8
Flight Controls
If you are not familiar with the controls of your Quadrone, please take a few minutes to review
them before take off.
Ascending/Descending
Throttle Up
Ascend
Throttle Down
Descend
Turning
Throttle Left
Nose Turns Left
Throttle Right
Nose Turns Right
Forward
Rudder Down
Backward
Sideways Left
Rudder Right
Sideways Right
Forward/Backward
Rudder Up
Sideways Flying
Rudder Left
360° Flips
To enter Flip Mode, press the button on the upper right corner of the remote controller.
The controller will begin to beep to indicate it has entered Flip Mode. Move the joystick
in any direction and the quad will perform a corresponding flip.
9
One Key Return
Hold the One Key Return button for 2 seconds. The quadcopter will beep and the tail light will
flash. The quadcopter will now return to the remote controller.
Headless Mode
Hold the Headless Mode button for 2 seconds and you will hear the controller begin to beep,
indicating it has entered Headless Mode. No matter what direction the quadcopter faces, it will
respond according to the direction pushed on the remote. (Forward on the remote will make the
quadcopter fly forward.) This makes flying simpler and more convenient for beginner pilots. To exit
Headless Mode, press the button again and you return to Normal Mode.
Headless Mode X-axis Y-axis Calibration
Often times after turning on the remote, the axises will need to be calibrated. To calibrate the
X-axis, hold the X-axis calibration button for 3 seconds. The LED lights will flash until the quad is
level. Calibration is complete. To calibrate the Y-axis, hold the Y-axis calibration button for 3
seconds. The LED lights will flash until the quad is level. Calibration is complete. Reboot your
quad for calibration to take effect.
Troubleshooting
Problem
Quadcopter LED blinks for more than 4
seconds after battery is inserted. No
response to remote controller.
Cause
Unable to sync quadcopter and remote.
Solution
Repeat syncing process. (See p 7)
No response after battery is connected to 1. No power to remote or drone.
2. Low battery power.
quadcopter.
3. Poor contact on battery terminals.
1. Turn on remote, properly insert drone
battery
2. Charge battery
3. Re-seat batteries properly
Motor does not respond to remote, LED
flashes.
Fully charge batteries.
Helicopter battery is drained.
Main rotor continues to spin after landing. Throttle trim accidentally increased during Confirm throttle trim is in the center or
flight.
slightly below.
Main rotor spins but unable to takeoff.
1. Rotor deformation
2. Quadcopter battery is drained.
1. Replace main blades.
2. Fully charge batteries.
Quadcopter strongly vibrates.
Rotor deformation
Replace the rotor.
Tail still off trim after adjustments, or
inconsistent speed during sideways
flying.
1. Damaged tail rotors
2. Damaged tail drive motor
1. Replace the rotor.
2. Replace the main motor.
10
Quadcopter still wanders forward after
trim adjustment during hover.
1. Surface during power up was not flat.
2. Trim was too long or too short.
Quadcopter still wanders forward after
trim adjustment during hover.
Cannot fly the quadcopter fully.
1. Motor fell out.
2. Gear is loose.
Cannot fly the quadcopter fully.
The quadcopter dramatically deviates
during headless mode.
1. Quadcopter is partially released from
headless mode.
2. Interference with headless mode.
Recalibrate headless mode on flat
surface.
Circuit Board
Tail lamp socket
Lamp socket
Lamp socket
Electric socket
Electric socket
Lamp socket
Lamp socket
11
Circuit Board
12
Parts List
No.
Part
Quantity
Propeller
2
1
Protective Guard
3
Upper Body
2
1
3
4
Receiver Board
6
Battery Cover
8
Electric Machinery
10
Lampshade
10
12
Carbon Fiber Spindle
12
14
Cone
14
Bearing
5
7
5
6
Battery
Light
9
11
4
Lower Body
13
Tail Light Plate
15
Tail Light Lamp Shade
Landing Feet
16
Quadcopter Parameters
Length
14.75”
Propeller Length
5.25mm
Height
2.25”
Battery Specification
Flight Time
13
3.7 730 mAh 23C
7-8 Minutes
7
8
9
11
13
15
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising