Performance Accessories GMC Sierra 1500 2014-2015 Body Lift Kit Installation Instructions
Below you will find brief information for Body Lift Kit GMC Sierra 1500 2014-2015. This installation manual provides detailed instructions on how to install the 2” Body Lift Kit on your GMC Sierra 1500 truck. From preparing the vehicle to final adjustments, follow the steps carefully for a safe and successful installation.
Advertisement
Advertisement
GMC SIERRA 1500 **ONLY**
GAS ENGINE
2” BODY LIFT KIT
INSTALLATION INSTRUCTIONS
2014-2015
KIT#
PA10302
WARNING
Installation of a
Performance Accessories bod y lift kit will change the vehicle’s center of gravity and handling characteristics both on- and off-road. Yo u must drive the vehicle safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
WARNING
Before you install this kit, read and understand all instructions, warnings, cautions, and notes in this instruction sheet and in the vehicle owner’s manual.
CAUTION
Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle. We strongly recommend that a certified mechanic familiar with the installation of similar components install this kit.
WARNING
DO NOT combine suspension, body, or other lift devices. Use of vehicle with combined lifts may result in unsafe and/or unexpected handling characteristics.
WARNING
This kit should only be installed on a vehicle that is in good working condition. Before you install the kit, thoroughly inspect the vehicle for corrosion or deformation of the sheet metal around the factory body mounts. If the vehicle is suspected to have been in a collision or misused, do not install this kit. Off-road use of your vehicle with this kit installed may increase the stress applied to the factory body mounts. We do not recommend that any vehicle with a body lift kit installed be involved in any extreme off-road maneuvers such as jumping. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.
WARNING
Many states and municipalities have laws restricting bumper heights and vehicle lifts. Consult state and local laws to determine if the changes you intend to make to the vehicle comply with the law.
WARNING
The installation of larger tires may reduce the effectiveness of the braking system.
WARNING
Always wear eye protection when operating power tools.
WARNING
Before you install this kit, block the vehicle tires to prevent the vehicle from rolling.
WARNING
Accidental deployment of the air bag can result in serious personal injury or death. To avoid accidental deployment during installation of the kit, the Supplemental Restraint System (SRS, or airbag) must remain deactivated. Do not allow anyone near the airbag during installation. Refer to the factory service manual or owner's manual for the recommended procedure to disable the SRS. After you install the kit, reactivate the
SRS before driving the vehicle.
NOTE
Performance Accessories recommends using the
Loctite® supplied in the kit on the threads of all kit nuts and bolts unless specified otherwise in these instructions.
1 2014-2015 GMC 1500 P/U - Kit
PA10292
Before Starting Installation
NOTE
Kit parts are prefaced by the word kit and appear in
bold print.
1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
NOTE
If parts are missing from kit, please be prepared to provide the following information:
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
5. Inspector # from inside box cover
3. Only install this kit on the vehicle for which it is
specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928)
636-7080.
4. Special tools needed:
a. Die grinder or plasma torch capable of cutting metal and plastic.
b. 3/8” and 1/2” drill bit
c. Center punch set
d. Telescoping magnet
e. *Welding required* (Manual Transfer Case Only)
5. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction.
Engine Compartment
1. Disconnect both battery cables. Disconnect negative cable first, then positive cable.
2. Airbag Fuse
NOTE
The location of the airbag fuse may vary; check the owner's manual.
a. Remove fuse cover.
b. Remove airbag fuse.
Prepare to Install Kit
Measurements
1. Measure and record distance between front bumper and fenders.
Driver Side ________ Passenger Side ________
2. Measure and record distance between rear bumper and bed
Driver Side ________ Passenger Side ________
3. Measure and record distance between cab and bed.
Driver Side ________ Passenger Side ________
Front of Vehicle
1. Front Bumper
a. Remove clips and cover from core support and grille.
Clips Cover
Core Support
Grille
2
Bolts
2014-2015 GMC 1500 P/U - Kit
PA10292
b. Remove four screws from upper grille and unclip two lower clips from lower grille as you prepair to remove grille from core support.
c. Remove two bolts from side fascia in inner fender wells with a 7mm socket in each fender well.
Bolts
f. Remove grille from core support.
Core Support Bumper
Dvr Fender Well
d. Remove four bolts from lower grille fascia with a
10mm socket on back-inside of lower grille.
g. Loosen three bolts and remove both bumper supports from each cab mount and bumper.
Bumper Support Bolts
Bolts
e. Disconnect fog lamp connectors from bumper, if equipped.
Connector
Bumper
Cab Mount
h. Remove four bolts and bumper from frame horns.
Bumper Bolt
3 2014-2015 GMC 1500 P/U - Kit
PA10292
i.
Remove six nuts and two bumper frame brackets from frame horns.
Frame Brackets
Bolts
Engine Compartment
1. Air intake
a. Pull up and remove cover from engine if equiped.
Cover Engine
j.
Remove four bolts, two nuts and two tow hooks from frame horns.
Frame
Rail
b. Loosen two clamps on airbox and engine intake.
c. Remove clip and upper radiator hose from engine intake.
Clamp Clamp
Bolts & Nuts
Tow Hook
k. Remove six bolts attaching lower guard to core support and frame. Remove guard.
Lower
Guard
Engine Intake
Clip, Upper Rad. Hose
2. Remove nut and ground strap from left firewall.
Left Firewall Nut & Ground Strap
l.
Remove ground strap bolts from body mounts.
Body Frame
Mount
Ground
Strap
Bolt
4 2014-2015 GMC 1500 P/U - Kit
PA10292
3. Remove brake lines from left frame rail and two clips.
Clips Left Frame Rail
Brake Lines
4. Remove left harness and clip from left firewall bracket, below brake master cylinder.
Left Firewall Brkt.
Clip & Wiring Harness
7. Steering Shaft
WARNING
Accidental deployment of the air bag can result in serious personal injury or death. To avoid accidental deployment during installation of the lift kit, the Supplemental Restraint System (SRS, or airbag) must remain deactivated. Do not allow anyone near the airbag during installation. Refer to the factory service manual or owner's manual for the recommended procedure to disable the SRS. After kit installation, the SRS must be reactivated before driving the vehicle.
CAUTION
If the following step is not performed, the airbag clockspring could be damaged. Do not turn the steering wheel while the steering shaft is disconnected.
a. Strap steering wheel to prevent accidental movement.
b. Mark upper steering shaft in relation to rack and pinion as shown.
c. Remove bolt and upper steering shaft from rack and pinion.
Upper Steering
Shaft
5. Remove harness from left wheel well, below fuse box.
6. Remove harness and clip from fuse box.
Clip & Harness Fuse Box
Bolt
Marks
Rack & Pinion
FRONT
5 2014-2015 GMC 1500 P/U - Kit
PA10292
Underside of Vehicle
1. Remove bolt, metal clip and harness from right frame rail.
Bolt, Metal Clip & Harness Right Frame Rail
c. Remove front cable from left frame body mount.
Left Frame Body Mount Cable
FRONT
2. Remove clip and harness from left frame rail.
Left Frame Rail Clip & Harness
4. Remove bolts and ground straps from front lef (Dvr), front right (Psg) frame, second left (Dvr) body mount, and second right (Psg) body mount.
Bolt & Ground Strap Left Frame Mount
FRONT
3. Parking brake cable
a. Using locking pliers, pull slack into rear cable.
b. Disconnect cable at junction near left frame rail.
Cable & Junction Left Frame Rail
FRONT LEFT & RIGHT
LEFT & RIGHT SECOND
FRONT
6 2014-2015 GMC 1500 P/U - Kit
PA10292
5. Remove bolt, metal clip and harness from right front frame rail.
Bolt, Metal Clip & Harness Right Frame Rail
a. Remove black wiring harness from junction on rear crossmember. (Above blue plug harness)
Junction Wiring Harness
6. Manual transfer case: shift linkage
FRONT
a. Remove clip containing three metal lines from bracket.
Bracket
Clip
Lines
Crossmember
b. Remove trailer light harness from bumper.
Harness Bumper b. Remove two nuts and bracket from transfer case. Bracket is not reused. Install two nuts and tighten.
Bracket
Transfer
Case Linkage
c. Remove four nuts, two double-bolt fasteners, four bolts and bumper from frame rails.
Frame Rail Bolts & Bumper
Nut behind bracket
Nut Transfer Case c. Remove two clips and transfer case linkage from transfer case and pivot.
Rear of Vehicle
1. Rear bumper
7 2014-2015 GMC 1500 P/U - Kit
PA10292
d. If equipped with a trailer hitch, remove two short and two long bolts from hitch and frame .
Hitch
Short Bolt
Frame
Install Kit
Cab
1. Prepare to lift cab from frame
a. Loosen, but DO NOT REMOVE, cab mounting bolts on left side.
Loosen Bolt
At These Mounts
Long Bolt
Cab Mount
(Core Support)
e. Remove two bolts and bumper from hitch and vehicle.
Bolt
Hitch Bumper
Cab Mount
(All Others)
b. Remove bolt (and nut for core support) and lower bushing from each cab mount on right side.
Remove Bolt
From These Mounts
Cab Mount
(Core Support)
8
Cab Mount
(All Others)
2014-2015 GMC 1500 P/U - Kit
PA10292
WARNING
Use extreme caution when lifting body from frame. To prevent serious personal injury, ensure the lifting device is securely placed. Keep your hands out from between the body and frame.
CAUTION
Continually check hoses, wires, lines, etc. to be sure that everything is flexing properly and not binding, or damage to the vehicle could result. Be especially careful of the a/c hoses at the fire wall, the belt pulley, and at the core support. Ensure brake lines stretch while lifting. Bending the lines to gain ample slack may be necessary. Be extremely careful not to kink the lines.
2. Right side of cab
a. Position a hydraulic floor jack and wood block(s) under right side of cab (under the body seam).
Slowly lift cab just enough to install a kit block on top of factory upper bushing.
Side Step & Body Seam Hydraulic Jack & Wood
Blocks
b. Remove plastic sleeves from all upper bushings.
Plastic Sleeves Upper Bushings
c. Install kit blocks onto upper bushings on each cab mount.
Kit
Block
(2x3)
Kit
Block (2x2)
WARNING
The kit blocks must be installed in addition to the factory upper and lower bushings. Installing the kit blocks without the factory upper and lower bushings could result in damage to the vehicle or serious personal injury.
Kit
Block
(2x3)
9
d. Lower cab onto kit blocks.
2014-2015 GMC 1500 P/U - Kit
PA10292
e. Install kit bolt (M12-1.75 x 170mm), thick
washer and O.E. nut into core support cab mount and kit block. DO NOT TIGHTEN.
(Note: Use a magnet from top of core support to remove
OE bolt and install kit bolt (M12-1.75 x 180mm) & thick
washer.)
Core Support
Kit
Block
g. Install kit bolt(M14-2.0 x 150mm) into remaining cab mounts and kit blocks. DO NOT TIGHTEN.
Cab
Kit
Block
Cab
Mount
Kit
Bolt(M12-1.75 x 170),
thick washer & O.E. Nut
f. Install kit bolt(M14-2.0 x 180mm) into cab mounts and kit blocks. DO NOT TIGHTEN.
Cab
Kit
Block
Cab
Mount
Kit
Bolt
(M14-2.0 x 150)
h. Repeat previous substeps for left side of cab.
i.
Remove each kit bolt, one at a time, and apply a small amount of kit Loctite® onto threads.
Install kit bolt and lower bushing (and O.E. nut for core support cab mount) into kit block and cab. TIGHTEN kit bolts to 55 ft. lbs.
Lower Bushing
Kit
Block
Cab
Mount
Kit
Bolt
(M14-2.0 x 180)
Kit
Bolt, O.E. Nut
Kit
Bolt, Lower Bushing
j.
Install ground straps onto front left, front right and second right body mount with bolts.
Bed
1. Prepare to lift bed from frame
10 2014-2015 GMC 1500 P/U - Kit
PA10292
a. Loosen, but DO NOT REMOVE, bed mounting bolts on left side.
Loosen Bolt
At These Mounts
Bed Mount
(Front)
d. Lower left side of bed and install kit bolt (M12-
1.75 x 80) and THICK WASHER at each bed mount. DO NOT TIGHTEN.
e. Repeat above substeps for left side of bed.
f. Remove each kit bolt, one at a time, and apply a small amount of kit Loctite® onto threads.
Install kit bolt and kit washer (M12) into kit
block and bed. TIGHTEN kit bolts to 55 ft. lbs.
Rear of Vehicle
1. Spare tire winch
a. Mark and cut crossmember as shown.
Crossmember Mark & Cut
Bed Mount
(Rear)
b. Remove bed mounting bolts on right side.
Remove Bolt
From These Mounts
Bed Mount
(Front)
Winch Tube
b. Using locking pliers, pull up on cut section of crossmember to allow winch tube to angle upward.
Cut Section Crossmember
Bed Mount
(Rear)
c. Slowly lift bed just enough to install kit block on top of each frame mount.
NOTE
The number of kit blocks used will vary depending on the length of the bed.
11 2014-2015 GMC 1500 P/U - Kit
PA10292
c. Using rust preventative paint, cover cut edges of crossmember.
Paint Exposed Metal Crossmember
c. Remove five torx bolts from each bumper bracket and remove bumper bracket from shell.
Bolts Bumper
Rear bumper
a. Remove two clips and two screws from fascia and bumper.
Bumper Fascia
Bolt
Bumper Bracket
d. Remove u-nuts from OE Bumper bracket and reinstall u-nuts onto kit bumper brackets.
Clips
Kit
Bumper Bracket
Clips Screws
b. Remove plastic fascia from corner of bumper by gently using a pry bar to loosen each clip.
Clips
Bumper
e. Position two kit brackets (bumper, rear) onto bumper and reinstall OE bolts.
Bolts Bumper
12
Bolt
Bumper Bracket
2014-2015 GMC 1500 P/U - Kit
PA10292
f. NOTE:Use two kit thick washers in-between kit
bumper bracket and bumper coner support bracket before installing both OE center bolts.
Kit
Thick Washer
Kit
Bracket (Bumper, Rear)
j.
Install bumper onto frame rails with two OE
bolts (14mm), two kit washers (14MM) and two
kit
nuts (14mm Flange). DO NOT TIGHTEN.
Frame Rail
Kit
Bracket (Bumper, Rear)
g. Tighten all kit bumper bracket bolts at this time; besure both bumper brackets are square to frame rails.
h. Reinstall corner fascia onto bumper shell with two clips and bolts in each corner.
i.
Install bumper onto frame rails with two O.E. double-bolt fasteners, two nuts, two OE bolts
(10mm) and two kit nuts (M10-1.5 Flange).
Snug, but DO NOT TIGHTEN.
Frame Rail
Kit
Bracket (Bumper, Rear)
OE
Bolt (14mm),
Kit
Washer (14mm),
Kit
Nut (14mm)
Nuts & Double-Bolt
Fasteners
k. Align bumper to previous measurements and
TIGHTEN all bumper hardware.
l.
Connect bumper wiring harness onto crossmember.
m. Connect trailer light harness onto bumper.
n. Install spare tire onto vehicle according to vehicle owner’s manual.
Underside of Vehicle
1. Crush blocks
NOTE
The number of kit blocks (crush) used will vary depending on the length of the bed.
a. Remove pads from two frame rails.
Pads Bed Rails
OE
Bolt (10mm),
Kit
Nut (M10-1.5 Flange)
Nuts & Double-Bolt
Fasteners
13 2014-2015 GMC 1500 P/U - Kit
PA10292
Kit
b. Install kit block (crush) onto each pad location of frame with kit bolt (5/16”- 3/4”self-tapping) and kit washers (5/16”).
Block (Crush)
Kit
Bolt (5/16”- 3/4” Self-
Tapping) & Washers (5/16”) b. Scribe a line along transfer case linkage as shown. Cut transfer case linkage into two pieces through the scribed line and deburr.
Scribed Line Cut Here
Transfer
Case
Linkage
NOTE
The following step is for vehicles with manual transfer case only. Other models skip this step.
2. Lengthen and install transfer case shift lever.
a. Remove two spring clips and transfer case linkage from shift lever, transfer case shift arm.
Transfer Case
Linkage
Spring Clip
WARNING
A certified welder should perform all welding.
c. Position kit pin 4x4 extension between two pieces of transfer case linkage. Ensure transfer case linkage scribed lines align and weld kit pin extension in place.
Kit Pin
Transfer Case Linkage
Transfer
Case
Shift Arm d. Install transfer case linkage on transfer case shift arm and shift lever with two clips.
e. Check transfer case shift lever operation.
Ensure there is complete engagement in all ranges. If necessary, adjust the linkage.
3. Parking brake cable
14 2014-2015 GMC 1500 P/U - Kit
PA10292
a. Install kit bracket (parking brake) onto second left cab mount with O.E. bolt. Mark hole with center punch.
Kit
Bracket (Parking Brake) Left Cab Mount
c. Install kit bracket (parking brake) and ground strap onto cab mount with O.E. bolt, kit bolt (5/
16”-18 x 1 1/4”), two kit washers (5/16”) and kit nut (5/16” Nylock)..
Front Cable
Kit
Bolt (5/16”-18 x 1 1/4”),
Kit
Washers (5/16”),
Kit
Nut (5/16” Nylock)
Mark Hole Bolt
b. Remove O.E. bolt and kit bracket (parking brake). Drill 3/8” hole through cab mount at marked location.
Drill Hole Left Cab Mount
Bolt & Ground Strap
Kit
Bracket (Parking Brake)
** Mid-2015+ Require New Kit Parking Cable Bracket **
d. Install kit 2015+ bracket (parking brake) with two kit bolts (5/16”-18 x 1 1/4”), four kit washers
(5/16”) and two kit nuts (5/16” Nylock) on top of frame body mount gusset, kit hardware will mount bracket through two existing holes on top of frame gusset.
Front Cable
Kit
2015+ Bracket (Parking Brake)
15
Kit
Bolts (5/16”-18 x 1 1/4”),
Kit
Washers (5/16”),
Kit
Nuts (5/16” Nylock)
e. Route parking brake cable through kit bracket
(parking brake) and connect front and rear brake cables with junction
f. Remove locking pliers from rear cable.
2014-2015 GMC 1500 P/U - Kit
PA10292
g. Reinstall three ground strap onto both front frame body mounts and passenger fender well frame body mount.
NOTE: Remove clip from ground harness and core support for extra slack in wiring harness.
Bolt & Ground Strap Left Frame Mount
b. Reinstall bolt and upper steering shaft from rack and pinion.
Upper Steering
Shaft
Bolt
Marks
FRONT LEFT & RIGHT
Engine Compartment
1. Steering Shaft
WARNING
Accidental deployment of the air bag can result in serious personal injury or death. To avoid accidental deployment during installation of the lift kit, the Supplemental Restraint System (SRS, or airbag) must remain deactivated. Do not allow anyone near the airbag during installation. Refer to the factory service manual or owner's manual for the recommended procedure to disable the SRS. After kit installation, the SRS must be reactivated before driving the vehicle.
CAUTION
If the following step is not performed, the airbag clockspring could be damaged. Do not turn the steering wheel while the steering shaft is disconnected.
a. line up marks upper steering shaft in relation to rack and pinion as shown.
Rack & Pinion
c. TIGHTEN bolts to 33 lb.-ft.
NOTE
It may be neccessary to bend the power steering line slightly away from the steering shaft and boot in next step.
d. Rotate power steering hose pinch clamp down and away from steering boot.
Steering Boot
16
Power Steering Line
Pinch Clip
2. Install kit bracket (2” w/ stud) onto left firewall stud with O.E. nut.
2014-2015 GMC 1500 P/U - Kit
PA10292
3. Install ground strap onto kit bracket (2” w/ stud) with
kit
washer (1/4” SAE) and kit nut (1/4” Nylock).
Kit
Bracket (2” W/ Stud) O.E. Nut an aftermarket intake hose, this step may be dismissed.
Electric Fan Shroud Marked
BEFORE
Kit
Washer (1/4” SAE),
Kit
Nut (1/4”-20 Nylock)
Ground Strap
4. Install harness and metal clip onto right frame rail with bolt.
5. Electric Fan Shroud Modification
a. Carefully Mark, Cut & Remove both inner verticle fan shroud support ribs as shown below:
NOTE: Doing so will allow the factory air intake housing to properly reinstall onto throttle body. If the vehicle has
AFTER
Electric Fan Shroud Marked
6. Air Intake
a. Reinstall air intake hose onto throttle body and air box port.
Clamp Clamp
Intake
Hose
17
Front of Vehicle
1. Pull slack into lines for transmission cooler to make sure they have adequate clearance everywhere needed.
2014-2015 GMC 1500 P/U - Kit
PA10292
a. Install lower guard to core support and frame with factory bolts.
Lower
Guard
a. Install kit bracket (bumper, front, left) and kit
bracket (bumper, front, right) onto left frame horn with six OE bolts. Align and TIGHTEN.
Kit
Bracket (Bumper, Front, Left)
Kit
Bracket (Bumper, Front, Right)
2. Front Tow Hooks
a. Carfully Mark & Drill each tow hook hole with a
1/2” drill bit 2” higher than the original location to relocate OE tow hooks.
Front Tow Hook Holes Marked
Frame Horns
OE
Bolts
b. Remove both front bumper brackets by removing all six bolts from each bracket.
3. Front bumper
Frame Horn
Tow Hook
OE
Bolts
Bumper
Inner Bumper Brackets
18 2014-2015 GMC 1500 P/U - Kit
PA10292
c. Carefully Mark, Cut & Remove a small section of the front bumper fascia were the tow hooks come through the bumper as shown below:
Front Bumper
d. Carefully Mark & Cut OE bumper brackets to clearance OE bracket and allow bumper to properly reposition 3” higher as shown below:
Psg Inner Bumper Bracket Marked
BEFORE
AFTER
NOTE: This step will allow the bumper to move up 3” properly with out interfering with the lower frame horns.
Psg Inner Bumper Bracket Cut
e. Carefully use a pair of pliers to straighten lower bumper support tab and reinstall u-nut clip facing upwards as shown below:
Bumper
Tab & U-Nut
19 2014-2015 GMC 1500 P/U - Kit
PA10292
f. Install both inner bumper bracket into stock locations, inside bumper shell, with ten OE bolts.
g. Using a pair of visegrips and OE bolt; align & mount each kit inner bumper bracket support onto OE bumper bracket and lower bumper support tab as shown below:
Kit
Inner Bumper Bracket Support
Tab
j.
Reconnect foglight wiring harnesses.
k. Install bumper onto frame brackets with four
O.E. bolts, four kit washers(12mm) and four kit
nuts(12mm). DO NOT TIGHTEN.
Bumper OE Bolts, Nuts & Washers
h. Drill four 3/8” holes into each OE bumper bracket using the kit inner bumper bracket
support as a guide for each 3/8” hole.
i.
Securely mount each kit inner bumper bracket
support using four kit bolts (3/8” x 1”), eight kit
washers (3/8” SAE) and four kit nuts (3/8” nylock).
Kit
Inner Bumper Bracket Support
l.
Install each bumper side support onto frame using two OE bolts. DO NOT TIGHTEN.
m. Reinstall each bumper side support onto bumper with Dvr and Psg side support bars switched from side to side as shown below:
DO NOT TIGHTEN.
Bumper Support Bolts
Kit
bolts (3/8” x 1”), washers (3/8”) & nuts (3/8”)
20
Cab Mount
n. Align bumper to previous measurements and
TIGHTEN all bumper hardware.
2014-2015 GMC 1500 P/U - Kit
PA10292
o. Reconnect fog lamp connector and attach onto bumper, if equipped.
Connector
Bumper
r. Reinstall two bolts into side fascia inside inner fender wells with a 7mm socket.
Bolts
Dvr Fender Well
p. Reinstall grille by inserting lower grille clips into lower core support and install four screws into upper grille on core support.
q. Reinstall front air shield along with clips .
Bolts
s. Reinstall four bolts into lower grille fascia with a
10mm socket on back-inside of lower grille.
Bolts
Core Support
Grille
Clips
Cover
21 2014-2015 GMC 1500 P/U - Kit
PA10292
After Completing Installation
Engine Compartment
1. Connect both battery cables. Connect positive cable first, then negative cable.
2. Install airbag fuse and fuse block cover.
Miscellaneous
1. Apply kit label (warning) onto dashboard in plain sight of all vehicle occupants.
2. Check all fasteners to ensure they are tight.
3. Ensure all wires, hoses, cables, etc. are properly connected and there is ample slack.
4. Adjust headlights.
Dynamic Vehicle Check
1. Check steering in both directions to ensure that there is no bind. Check operation of clutch, brake system, and parking brake. Check operation of transmission and transfer case. Ensure there is full engagement in all gears and 4WD ranges. Check battery connections and electrical component operations. Test-drive vehicle.
Accessories
WARNING
Retorque all fasteners after 500 miles and after off road use. All body lift components should be visually inspected and fasteners retorqued during routine vehicle servicing.
CAUTION
Performance Accessories does not recommend any particular wheel and tire combinations for use with its body lifts and cannot assume responsibility for the customer’s choice of wheels and tires. Refer to you r owner's manual for recommended tire sizes and warnings related to the use of oversized tires. Larger wheel and tire combinations increase stress and wear o n steering and suspension components, which leads t o increased maintenance and higher risk for component failure. Larger wheel and tire combinations also alter speedometer calibration, braking effectiveness, center of gravity, and handling characteristics. Consult an experienced local off road shop to find what wheel and tire combinations work best with your vehicle.
NOTE
All warranty information, instruction sheets, and other documents regarding the installation of this product must be retained by the vehicle owner. Information contained in the instructions and on the warranty card will be required for any warranty claims. The vehicle owner needs to understand the modifications made to the vehicle and how they affect vehicle handling and performance. Failure to provide the customer with this information can result in damage to the vehicle and severe personal injury.
Kit# 6547 Gap Guards
22 2014-2015 GMC 1500 P/U - Kit
PA10292
KIT PARTS LIST
Qty.
Description
1
4
1
1
14
8
2
2
1
1
1
1
1
1
2
14
2
4
1
1
2
2
8
1
4
2
1
16
8
2
1
2
4
1
2
8
Block
Block (mini)
Block (crush)
Bracket (frame, front, dvr)
Bracket (frame, front, psg)
Bracket (bumper, front, lower)
Bracket (bumper, rear, dvr)
Bracket (bumper, rear, psg)
Label (logo)
Label (warning)
Loctite® (6ml bottle)
BP10292 (Bolt pack)
Bolt (M12-1.75 x 80)
Bolt (M12-1.75 x 180)
Bolt (M14-2.0 x 150)
Bolt (M14-2.0 x 180)
Bracket (parking brake)
Bracket (2015+ parking brake)
Washer (Thick)
HP10292 (Hardware pack)
Bolt (5/16” x 1 1/4”)
Bolt (3/8” x 1”)
Bolt (5/16”-18 x 3/4” self-tapping)
Bracket (2” with stud)
Nut (1/4”-20 Nylock)
Nut (5/16” Nylock)
Nut (3/8” Nylock)
Nut (10mm Flange)
Nut (12mm Flange)
Nut (14mm Flange)
Pin, 4x4 extension, 1/2” X 1”
Washer (3/8” SAE)
Washer (5/16” USS)
Washer (1/4” SAE)
Washer (10mm)
Washer (14mm)
23
Copyright 11/15
Performance Accessories
www.
PerformanceAccessories.com
2014-2015 GMC 1500 P/U - Kit
PA10292

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 2” lift for GMC Sierra 1500
- Detailed installation instructions
- Comprehensive parts list
- Safety warnings and precautions
- Recommended tools and procedures
- Step-by-step instructions for all components
- Final adjustments and checks
- Post-installation instructions