IVES Cat.Comm.Cover - Precision Door Hardware Co Inc

IVES Cat.Comm.Cover - Precision Door Hardware Co Inc
IVES Customer Service:
1-877-613-8766
1-877-424-8494 FAX
DIVISION
8
©2003 Ingersoll-Rand
Form IV-2001C
Rev. 4/03
Printed in USA
Table of Contents
General Information
Index by Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii, iii
Alphanumeric Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv – vii
Finish List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii, ix
Packaging, Handing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x
Ives & Glynn-Johnson Product Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi, xii, xiii
Product Category
Section
Flush Bolts, Coordinators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A
Pivots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B
Architectural Door Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C
Floor Stops, Wall Stops, Bumpers, Silencers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D
Surface Bolts, Dutch Door Bolts, Door Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E
Exterior Door Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F
Latches, Catches & Mortise Door Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G
Hooks & Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H
Window Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I
Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J
Cabinet Knobs & Pulls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K
Hobby Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L
i
Index by Product Description
A
Page(s)
Adjustable catch . . . . . . . . . . . . . . . . . . . . .I6
Adjuster, casement . . . . . . . . . . . . . . . .I4, I5
Applied stop . . . . . . . . . . . . . . . . . . . . . . .G4
Architectural door trim . . . . . . . . . . .C1-C17
Armor plates . . . . . . . . . . . . . . . . . . . . . .C14
Automatic floor holder . . . . . . . . . . .D9, D10
Automatic flush bolt . . . . . . . . . . . . . .A1, A2
Automatic wall holder . . . . . . . . . . . . . . .D19
Auxiliary pusher . . . . . . . . . . . . . . . . . . . .G6
B
Back plate, knob . . . . . . . . . . . . . . . . . . . .K1
Back plate, mail slot . . . . . . . . . . . .F14-F17
Ball catch . . . . . . . . . . . . .G5, G6, G11, G12
Base door stop . . . . . . . . . . . . . . . .D22, D23
Bar window lift . . . . . . . . . . . . . . . . . . . . . .I3
Barrel bolt (HH*) . . . . . . . . . . . . . . . . . . . .L1
Beaded pull . . . . . . . . . . . . . . . . . . . . . . . .K3
Blind holdbacks . . . . . . . . . . . . . . . . . . . . .I6
Bolt, door . . . . . . . . . . . . . . . . . . . . .G14, K7
Bolt, dutch door . . . . . . . . . . . . . . . . . . .E10
Bolt, flush . . . . . . . . . . . . . .A1-A8, A10, A11
Bolt, mortise . . . . . . . . . . . . . . . . . . . . . .G14
Bolt, security . . . . . . . . . . . . . . . . . . . . . .E11
Bolt, surface . . . . . . . . . . . . . . . . . . . .E1-E9
Bracket (HH*) . . . . . . . . . . . . . . . . . . . . . .L7
Bracket, handrail . . . . . . . . . . . . . . . .H1, H2
Bumper, roller . . . . . . . . . . . . . . . . . . . . .D22
Bumper, wall . . . . . . . . . . . . . . . . . .D13-D18
C
Cabinet catch . . . . . . . . . . . . . . . . . . . . . .K4
Cabinet knob (HH*) . . . . . . . . . . . . . . . . .L2
Cabinet knob . . . . . . . . . . . . . . . . . . .K1, K2
Cabinet latch . . . . . . . . . . . . . . . . . . .G5, G6
Carry bar . . . . . . . . . . . . . . . . . . . . . . . . .A16
Casement adjuster . . . . . . . . . . . . . . . .I4, I5
Casement fastener . . . . . . . . . . . . . . . . . . .I4
Catch, adjustable . . . . . . . . . . . . . . . . . . . .I6
Catch, ball . . . . . . . . . . . .G5, G6, G11, G12
Catch, cabinet . . . . . . . . . . . . . . . . . . . . . .K4
Catch, draw (HH*) . . . . . . . . . . . . . . .L7, L8
Catch, friction (HH*) . . . . . . . . . . . . . . . . .L1
Catch, magnetic . . . . . . . . . . . . . . . . .G7, G8
Catch, roller . . . . . . . . . . . . . . . . . . .G9, G10
Catch, snap (HH*) . . . . . . . . . . . . . . . . . .L8
Catch, transom . . . . . . . . . . . . . . . . . . . . . .I5
Ceiling hook . . . . . . . . . . . . . . . . . . . . . . .H5
ii
Center hung pivot . . . . . . . . . . . . . .B16-B20
Chain door guard . . . . . . . . . . . . . . . . . .E12
Chain, transom . . . . . . . . . . . . . . . . . . . . .I5
Chest handle (HH*) . . . . . . . . . . . . . . . . .L8
Chime, door . . . . . . . . . . . . . . . . . . . . . . .F5
Closer, pneumatic door . . . . . . . . . . . . . .F18
Closet pole sockets . . . . . . . . . . . . . . . . .H6
Coat and hat hook . . . . . . . . . . . . . . . . .H3-5
Combination roller
latch/applied stop . . . . . . . . . . . . . . . . . . .G2
Constant latching flush bolt . . . . . . . .A3, A4
Continuous hinge (HH*) . . . . . . . . . . . . . .L2
Coordinator, bar . . . . . . . . . . . . . . .A12-A15
Coordinator, gravity arm . . . . . . . . . . . . .A16
Corners (HH*) . . . . . . . . . . . . . . . . . . . . . .L7
Countersunk washer . . . . . . . . . . . . . . . . .I6
Crash stop . . . . . . . . . . . . . . . . . . . . . . . .F4
Cupboard turn (latch) . . . . . . . . . . . . . . .G13
D
Dome stop . . . . . . . . . . . . . . . . . . . . .D1-D3
Door bolt, mortise . . . . . . . . . . . . . . . . .G14
Door bolt, pocket . . . . . . . . . . . . . . . . . . .K7
Dome chime . . . . . . . . . . . . . . . . . . . . . . .F5
Door edge pull . . . . . . . . . . . . . . . . . . . . .K7
Door guard . . . . . . . . . . . . . . . . . . . . . . .E12
Door knocker . . . . . . . . . . . . . . . . . . .F8-F11
Door latch, storm . . . . . . . . . . . . . . . . . . .F5
Door lock, sliding . . . . . . . . . . . . . . . . . . .K8
Door protection plates . . . . . . . . . .C14, C15
Door pull, architectural . . . . . . . . . .C1-C13
Door pull, screen . . . . . . . . . . . . . . . . . . .F5
Door silencers . . . . . . . . . . . . . . . . . . . .D21
Door stops . . . . . . . . .see floor or wall stops
Door trim, architectural . . . . . . . . . .C1-C17
Door viewer . . . . . . . . . . . . . . . . . . . .F6-F11
Draw catch (HH*) . . . . . . . . . . . . . . . .L7, L8
Drawer pull . . . . . . . . . . . . . . . . . . . . . . . .K4
Drop leaf support (HH*) . . . . . . . . . . . . . .L7
Dust proof strikes . . . . . . . . . . . . . . . . . . .A9
Dutch door bolt . . . . . . . . . . . . . . . . . . . .E10
Dutch door quadrant . . . . . . . . . . . . . . . .E10
E
Elbow cabinet catch . . . . . . . . . . . . . . . . .K4
F
Fastener guide,
architectural door trim . . . . . . . . . .C11-C13
Fastener, casement . . . . . . . . . . . . . . . . . . .I4
Filler bar for coordinators . . . . . . . . . . . .A12
Finger pull . . . . . . . . . . . . . . . . . . . . .K5-K7
Flexible door stop . . . . . . . . . . . . . . . . . .D22
Floor stop and/or holder . . . . . . . . .D1-D12,
D22, D23
Floor stop, automatic holder . . . . . .D9, D10
Floor stop, dome . . . . . . . . . . . . . . . .D1-D3
Floor stop, kick down . . . . . . . . . . . . . . .D12
Floor stop, plunger type . . . . . . . . . . . . .D11
Floor stop, security . . . . . . . . . . . . . . . . .D4
Flush bolt, automatic . . . . . . . . . . . . .A1, A2
Flush bolt, constant latching . . . . . . .A3, A4
Flush bolt, manual . . . . . . .A5-A8, A10, A11
Flush pull . . . . . . . . . . . . . . . . . . . . . .K5-K7
Flush pull ring (HH*) . . . . . . . . . . . . . . . .L1
Flush ring pull . . . . . . . . . . . . . . . . . . . . .K7
Friction casement adjuster . . . . . . . . . . . . .I4
Friction catch (HH*) . . . . . . . . . . . . . . . . .L1
Friction lid support (HH*) . . . . . . . . . . . . .L6
G
Gasket tape, kick plate . . . . . . . . . . . . . .C14
Gravity arm coordinator . . . . . . . . . . . . .A16
Guard, door . . . . . . . . . . . . . . . . . . . . . . .E12
Guard, lock . . . . . . . . . . . . . . . . . . . . .F1-F3
H
Handrail bracket . . . . . . . . . . . . . . . . .H1, H2
Hasp (HH*) . . . . . . . . . . . . . . . . . . . . .L5, L6
Hinge pin door stop . . . . . . . . . . . . . . . .D23
Hinge, butt (HH*) . . . . . . . . . . . . . . . .L2, L3
Hinge, continuous (HH*) . . . . . . . . . . . . .L2
Hinge, decorative (HH*) . . . . . . . . . . .L4, L5
Hinge, residential . . . . . . . . . . . . . . . . . . .J8
Hinge, support (HH*) . . . . . . . . . . . . . . . .L6
Hobby hardware (HH*) . . . . . . . . . . . .L1-L8
Holdbacks, blind . . . . . . . . . . . . . . . . . . . .I6
Hook and staple (HH*) . . . . . . . . . . . . . . .L1
Hook, ceiling . . . . . . . . . . . . . . . . . . . . . .H5
Hook, coat and hat . . . . . . . . . . . . . . .H3-H5
Hook, wardrobe . . . . . . . . . . . . . . . . . . . .H5
Hook window lift . . . . . . . . . . . . . . . . . . . .I3
House numbers . . . . . . . . . . . . . . .F12, F13
Hinge architectural . . . . . . . . . . . . . . . .J1-J7
Index by Product Description
I
Invisible latch . . . . . . . . . . . . . . . . . . . . . .G6
K
Kick down floor stop . . . . . . . . . . . . . . .D12
Kick plates . . . . . . . . . . . . . . . . . . . . . . .C14
Kick plate gasket tape . . . . . . . . . . . . . . .C14
Knob back plate . . . . . . . . . . . . . . . . . . . .K1
Knob, cabinet . . . . . . . . . . . . . . . . . . .K1, K2
Knob, cabinet (HH*) . . . . . . . . . . . . . . . . .L2
Knocker, door . . . . . . . . . . . . . . . . . .F8-F11
L
Latch, invisible . . . . . . . . . . . . . . . . . . . . .G6
Latch, push . . . . . . . . . . . . . . . . . . . . . . .G13
Latch, roller . . . . . . . . . . . . . . . . . . . .G1, G2
Latch, storm door . . . . . . . . . . . . . . . . . . .F5
Latch, touch . . . . . . . . . . . . . . . . . . . . . .G13
Letter Box Plates . . . . . . . . . . . . . . .F14-F17
Lid support (HH*) . . . . . . . . . . . . . . . . . . .L6
Line cleat . . . . . . . . . . . . . . . . . . . . . . . . .H6
Lock guard . . . . . . . . . . . . . . . . . . . . .F1-F3
Lock, sliding door . . . . . . . . . . . . . . . . . . .K8
Lock, window . . . . . . . . . . . . . . . . . . . .I1, I2
M
Magnetic catch . . . . . . . . . . . . . . . . .G7, G8
Magnetic kick plates . . . . . . . . . . . . . . . .C15
Mail sleeve . . . . . . . . . . . . . . . . . . .F16, F17
Mail slot . . . . . . . . . . . . . . . . . . . . .F14-F17
Manual flush bolt . . . . . . . .A5-A8, A10, A11
Mop plates . . . . . . . . . . . . . . . . . . . . . . .C14
Mortise bolt . . . . . . . . . . . . . . . . . . . . . .G14
Mounting brackets (coordinators) . . . . .A13
N
Numbers, house . . . . . . . . . . . . . . .F12, F13
O
Offset pivot . . . . . . . . . . . . . . . .B1-B15, B20
Open window lock . . . . . . . . . . . . . . . . . . .I2
P
Padlock with key (HH*) . . . . . . . . . . . . . . .L1
Pivots, center hung . . . . . . . . . . . . .B16-B20
Pivots, offset . . . . . . . . . . . . . . .B1-B15, B20
Pivots, pocket . . . . . . . . . . . . . . . . .B21, B22
Pivots, power transfer . . . . . . . . . . .B20, B21
Plate, door protection
(kick plates) . . . . . . . . . . . . . . . . . .C14, C15
Plate, pull . . . . . . . . . . . . . . . . . . . . .C8-C10
Plate, push . . . . . . . . . . . . . . . . . . . . . . . .C8
Plunger door holder . . . . . . . . . . . . . . . .D11
Pneumatic door closer . . . . . . . . . . . . . .F18
Pocket door bolt . . . . . . . . . . . . . . . . . . . .K8
Pocket pivot . . . . . . . . . . . . . . . . . .B21, B22
Pull plate . . . . . . . . . . . . . . . . . . . . .C8-C10
Pull, architectural door . . . . . . . . . . .C1-C10
Pull, beaded . . . . . . . . . . . . . . . . . . . . . . .K3
Pull, door edge . . . . . . . . . . . . . . . . . . . . .K7
Pull, drawer . . . . . . . . . . . . . . . . . . . . . . .K4
Pull, finger . . . . . . . . . . . . . . . . . . . . .K5-K7
Pull, flush . . . . . . . . . . . . . . . . . . . . . .K5-K7
Pull, flush ring . . . . . . . . . . . . . . . . . . . . .K7
Pull, screen door . . . . . . . . . . . . . . . . . . . .F5
Pull, sliding door . . . . . . . . . . . . . . . .K7, K8
Pull, utility . . . . . . . . . . . . . . . . . . . . . . . . .I3
Pull, wire . . . . . . . . . . . . . . . . . . . . . .K3, K4
Push latch . . . . . . . . . . . . . . . . . . . . . . .G13
Push plate . . . . . . . . . . . . . . . . . . . . . . . .C8
Pusher, auxiliary . . . . . . . . . . . . . . . . . . . .G6
Q
Quadrant, dutch door . . . . . . . . . . . . . . .E10
R
Residential hinges . . . . . . . . . . . . . . . . . . .J8
Risers, dome stops . . . . . . . . . . . . . . .D1-D3
Roller bumper . . . . . . . . . . . . . . . . . . . . .D20
Roller catch . . . . . . . . . . . . . . . . . . .G9, G10
Roller latch . . . . . . . . . . . . . . . . . . . .G1, G2
T
Touch latch . . . . . . . . . . . . . . . . . . . . . . .G13
Transom catch . . . . . . . . . . . . . . . . . . . . . .I5
Transom chain . . . . . . . . . . . . . . . . . . . . . .I5
Trim, architectural door . . . . . . . . . .C1-C17
Trim, vandal-resistant . . . . . . . . . .C16, C17
U
Utility pull . . . . . . . . . . . . . . . . . . . . . . . . .I3
V
Vandal-resistant trim . . . . . . . . . . .C16, C17
Viewer, door . . . . . . . . . . . . . . . . . . .F6-F11
W
Wall bumpers . . . . . . . . . . . . . . . . .D13-D18
Wall stop and/or holder . . . . . . . . .D13-D23
Wall, automatic holder . . . . . . . . . . . . . .D19
Wardrobe hook . . . . . . . . . . . . . . . . . . . . .H5
Washers, countersunk . . . . . . . . . . . . . . . .I6
Window lift . . . . . . . . . . . . . . . . . . . . . . . . .I3
Window lock . . . . . . . . . . . . . . . . . . . . .I1, I2
Window stop adjusters . . . . . . . . . . . . . . .I6
Wire coat and hat hook . . . . . . . . . . . . . . .H4
Wire pull . . . . . . . . . . . . . . . . . . . . . . .K3, K4
Wire pull base . . . . . . . . . . . . . . . . . . . . . .K4
* Denotes Hobby Hardware (HH)
S
Screen door pull . . . . . . . . . . . . . . . . . . . .F5
Security bolt . . . . . . . . . . . . . . . . . . . . . .E11
Security floor/wall stop . . . . . . . . . . . . . .D4
Sex bolts . . . . . . . . . . . . . . . . .with products
Shutter bar . . . . . . . . . . . . . . . . . . . . . . . . .I5
Shutter holdbacks . . . . . . . . . . . . . . . . . . .I6
Side window lock . . . . . . . . . . . . . . . . . . . .I2
Silencers, door . . . . . . . . . . . . . . . . . . . .D21
Sliding door lock . . . . . . . . . . . . . . . . . . .K8
Sliding door pull . . . . . . . . . . . . . . . .K7, K8
Snap catch . . . . . . . . . . . . . . . . . . . . . . .128
Sockets, closet pole . . . . . . . . . . . . . . . . .H6
Storm door latch . . . . . . . . . . . . . . . . . . . .F5
Stretcher plates . . . . . . . . . . . . . . . . . . . .C14
Strikes, optional roller latch . . . . . . . . . . .G3
Support hinge (HH*) . . . . . . . . . . . . . . . . .L6
Surface bolt . . . . . . . . . . . . . . . . . . . . .E1-E9
iii
Alphanumeric Index
Products with Alpha Model Names are listed first, then followed by Products with Numeric Model Names.
A
Page(s)
AS18 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G4
AS895 . . . . . . . . . . . . . . . . . . . . . . . . . . .G4
C
CB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A16
CL11 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G6
CL12 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G6
CL14 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G6
CL21 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G5
CL21A . . . . . . . . . . . . . . . . . . . . . . . . . . .G5
CL22 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G5
COR7G . . . . . . . . . . . . . . . . . . . . . . . . . .A16
COR9G . . . . . . . . . . . . . . . . . . . . . . . . . .A16
COR32 . . . . . . . . . . . . . . . . . . . . . .A12-A15
COR42 . . . . . . . . . . . . . . . . . . . . . .A12-A15
COR52 . . . . . . . . . . . . . . . . . . . . . .A12-A15
COR60 . . . . . . . . . . . . . . . . . . . . . .A12-A15
COR72 . . . . . . . . . . . . . . . . . . . . . .A12-A15
CS115 . . . . . . . . . . . . . . . . . . . . . . . . . . . .F4
D
DP1
DP2
DP3
DP4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .A9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .A9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .A9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .A9
F
FB31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A1
FB32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A1
FB33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A1
FB41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A2
FB42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A2
FB51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A3
FB52 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A3
FB53 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A3
FB61 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A4
FB62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A4
FB256N . . . . . . . . . . . . . . . . . . . . . . . . . .A5
FB257N . . . . . . . . . . . . . . . . . . . . . . . . . .A5
FB258N . . . . . . . . . . . . . . . . . . . . . . . . . .A5
FB358 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A6
FB457 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A7
FB457N . . . . . . . . . . . . . . . . . . . . . . . . . .A7
FB458 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A8
FB458N . . . . . . . . . . . . . . . . . . . . . . . . . .A8
FB0458N . . . . . . . . . . . . . . . . . . . . . . . . .A8
FL20 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A14
FL32 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A14
iv
FL44 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A14
FS9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D8
FS13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D1
FS17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D1
FS18S . . . . . . . . . . . . . . . . . . . . . . . . . . .D4
FS18L . . . . . . . . . . . . . . . . . . . . . . . . . . . .D4
FS40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D9
FS41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D9
FS42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D9
FS43 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D9
FS434 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D4
FS436 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D2
FS438 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D2
FS441 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D5
FS442 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D5
FS444 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D6
FS446 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D7
FS448 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D6
FS450 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D7
FS451 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D7
FS452 . . . . . . . . . . . . . . . . . . . . . . . . . . .D12
FS455 . . . . . . . . . . . . . . . . . . . . . . . . . . .D12
FS495 . . . . . . . . . . . . . . . . . . . . . . . . . . .D10
FS496 . . . . . . . . . . . . . . . . . . . . . . . . . . .D10
FS497 . . . . . . . . . . . . . . . . . . . . . . . . . . .D10
FS544 . . . . . . . . . . . . . . . . . . . . . . . . . . .D12
FS555 . . . . . . . . . . . . . . . . . . . . . . . . . . .D12
FS1153 . . . . . . . . . . . . . . . . . . . . . . . . . .D11
FS1154 . . . . . . . . . . . . . . . . . . . . . . . . . .D11
H
HB158 . . . . . . . . . . . . . . . . . . . . . . . . . . .H1
HB159A . . . . . . . . . . . . . . . . . . . . . . . . . .H1
HB159A . . . . . . . . . . . . . . . . . . . . . . . . . .H1
HB162 . . . . . . . . . . . . . . . . . . . . . . . . . . .H2
L
LG1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F1
LG7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F1
LG10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F2
LG11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F2
LG12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F2
LG13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F3
LG14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F3
M
MB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A13
MB1F . . . . . . . . . . . . . . . . . . . . . . . . . . .A13
MB1V . . . . . . . . . . . . . . . . . . . . . . . . . . .A13
MB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A13
MB2F . . . . . . . . . . . . . . . . . . . . . . . . . . .A13
MB2V . . . . . . . . . . . . . . . . . . . . . . . . . . .A13
MB3 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A13
MB3F . . . . . . . . . . . . . . . . . . . . . . . . . . .A13
MB3V . . . . . . . . . . . . . . . . . . . . . . . . . . .A13
R
R14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D1
R435 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D2
R437 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D3
RB470 . . . . . . . . . . . . . . . . . . . . . . . . . .D20
RB471 . . . . . . . . . . . . . . . . . . . . . . . . . .D20
RB472 . . . . . . . . . . . . . . . . . . . . . . . . . .D20
RL30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G1
RL32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G1
RL36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G2
RL38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G2
RL1152 . . . . . . . . . . . . . . . . . . . . . . . . . . .G2
S
SB360 . . . . . . . . . . . . . . . . . . . . . . . . . . . .E3
SB453 . . . . . . . . . . . . . . . . . . . . . . . . . . . .E4
SB454 . . . . . . . . . . . . . . . . . . . . . . . . . . . .E5
SB0454 . . . . . . . . . . . . . . . . . . . . . . . . . . .E6
SB1600M1 . . . . . . . . . . . . . . . . . . . . . . . .E2
SB1600M2 . . . . . . . . . . . . . . . . . . . . . . . .E2
SB1630 . . . . . . . . . . . . . . . . . . . . . . . . . . .E1
SB1640 . . . . . . . . . . . . . . . . . . . . . . . . . . .E1
SR64 . . . . . . . . . . . . . . . . . . . . . . . . . . .D21
SR65 . . . . . . . . . . . . . . . . . . . . . . . . . . .D21
SR66 . . . . . . . . . . . . . . . . . . . . . . . . . . .D21
STK685 . . . . . . . . . . . . . . . . . . . . . . . . . .G3
STK685L . . . . . . . . . . . . . . . . . . . . . . . . .G3
STK726 . . . . . . . . . . . . . . . . . . . . . . . . . .G3
V
VR900 . . . . . . . . . . . . . . . . . . . . . . . . . .C16
VR910 . . . . . . . . . . . . . . . . . . . . . .C16, C17
W
WS11 . . . . . . . . . . . . . . . . . . . . . . . . . . .D16
WS11X . . . . . . . . . . . . . . . . . . . . . . . . . .D16
WS20 . . . . . . . . . . . . . . . . . . . . . . . . . . .D18
WS20X . . . . . . . . . . . . . . . . . . . . . . . . . .D18
WS33 . . . . . . . . . . . . . . . . . . . . . . . . . . .D16
WS33X . . . . . . . . . . . . . . . . . . . . . . . . . .D16
WS40 . . . . . . . . . . . . . . . . . . . . . . . . . . .D19
WS45 . . . . . . . . . . . . . . . . . . . . . . . . . . .D19
Alphanumeric Index
WS45X . . . . . . . . . . . . . . . . . . . . . . . . . .D19
WS65 . . . . . . . . . . . . . . . . . . . . . . . . . . .D17
WS401CCV . . . . . . . . . . . . . . . . . . . . . .D13
WS401CVX . . . . . . . . . . . . . . . . . . . . . .D13
WS402CCV . . . . . . . . . . . . . . . . . . . . . .D13
WS402CVX . . . . . . . . . . . . . . . . . . . . . .D13
WS404CVX . . . . . . . . . . . . . . . . . . . . . .D13
WS406CCV . . . . . . . . . . . . . . . . . . . . . .D14
WS406CVX . . . . . . . . . . . . . . . . . . . . . .D14
WS407CCV . . . . . . . . . . . . . . . . . . . . . .D14
WS407CVX . . . . . . . . . . . . . . . . . . . . . .D14
WS443 . . . . . . . . . . . . . . . . . . . . . . . . . .D17
WS445 . . . . . . . . . . . . . . . . . . . . . . . . . .D18
WS447 . . . . . . . . . . . . . . . . . . . . . . . . . .D17
WS449 . . . . . . . . . . . . . . . . . . . . . . . . . .D18
0 - 99
0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I2
1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I6
2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K4
3CB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J4
3CB1 NRP . . . . . . . . . . . . . . . . . . . . . . . . .J4
3CB1HW . . . . . . . . . . . . . . . . . . . . . . . . . .J5
3CB1HW NRP . . . . . . . . . . . . . . . . . . . . . .J5
3PB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J4
3SP1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J5
4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I1
5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
5BB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J6
5BB1 NRP . . . . . . . . . . . . . . . . . . . . . . . . .J6
5BB1HW . . . . . . . . . . . . . . . . . . . . . . . . . .J7
5BB1HW NRP . . . . . . . . . . . . . . . . . . . . . .J7
5BB1SC . . . . . . . . . . . . . . . . . . . . . . . . . .J7
5BB1SH . . . . . . . . . . . . . . . . . . . . . . . . . .J6
5PB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J6
6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I6
07 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I1
9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I1
14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I3
15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F4
22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K5
25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F5
026 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I3
26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I3
27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I3
31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I5
33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K3
34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K3
36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K3
37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K3
38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K3
40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E7
42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K7
043 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E7
43 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E7
S48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
054 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E10
55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E10
56 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E10
059 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H2
59 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H2
060 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D22
60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D22
061 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D22
61 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D22
062 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D22
62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D22
64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D23
65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D17
066 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I4
66 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I4
69 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D23
70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D23
71 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I5
78 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L1
80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I5
82 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I5
86 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L1
87 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E11
89 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L1
90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I2
100 - 199
115 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F4
133 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K3
137 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K4
144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E8
145 . . . . . . . . . . . . . . . . . . . . . . . . . . . . G14
146 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
147 . . . . . . . . . . . . . . . . . . . . . . . . . . . . G14
148 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
149 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
150 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
151 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
152 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
153 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
154 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
155 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G14
158 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H1
159A . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H1
159A . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H1
162 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H2
200 - 299
218 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K5
220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K5
221 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K5
222 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K6
223 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K6
225 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K6
226 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K6
227 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K6
230 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K7
253 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E8
256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A5
257 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A5
258 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A5
260 . . . . . . . . . . . . . . . . . . . . . . . . . . . . A10
261 . . . . . . . . . . . . . . . . . . . . . . . . . . . . A10
262 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A10
263 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A10
264 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A11
265 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A11
266 . . . . . . . . . . . . . . . . . . . . . . . . . . . .A11
287 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I4
288 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I4
300 - 399
323 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G7
324 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G7
325 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G7
326 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G8
327 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G8
328 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L1
330 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G9
335 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G9
336 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G9
337 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G10
345 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G11
346 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G11
347 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G11
348 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G12
349 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G12
350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I6
353 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E8
354 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E9
358 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A6
360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E3
PRS375 . . . . . . . . . . . . . . . . . . . . . . . . . . .I6
400 - 499
401 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D13
401 1 /2 . . . . . . . . . . . . . . . . . . . . . . . . .D13
402 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D13
v
Alphanumeric Index
Products with Alpha Model Names are listed first, then followed by Products with Numeric Model Names.
402 1 /2 . . . . . . . . . . . . . . . . . . . . . . . . .D13
404 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D13
405 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H3
406 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D14
406 1 /2 . . . . . . . . . . . . . . . . . . . . . . . . .D14
407 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D14
407 1 /2 . . . . . . . . . . . . . . . . . . . . . . . .D14
408 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D15
408 1 /2 . . . . . . . . . . . . . . . . . . . . . . . . .D15
409 1 /2 . . . . . . . . . . . . . . . . . . . . . . . . .D15
411R . . . . . . . . . . . . . . . . . . . . . . . . . . . .D15
420 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L1
425 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K7
426 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K7
430 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D23
434 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D4
435 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D2
436 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D2
437 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D3
438 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D2
441 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D5
442 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D5
443 . . . . . . . . . . . . . . . . . . . . . . . . . . . . D17
444 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D6
445 . . . . . . . . . . . . . . . . . . . . . . . . . . . . D18
446 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D7
447 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D17
448 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D6
449 . . . . . . . . . . . . . . . . . . . . . . . . . . . . D18
450 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D7
451 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D7
452 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D12
453 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E4
0454 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E6
454 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E5
455 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D12
457 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A7
457 1 /2 . . . . . . . . . . . . . . . . . . . . . . . . . .A7
458 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A8
458 1 /2 . . . . . . . . . . . . . . . . . . . . . . . . . .A8
0458 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A8
466 . . . . . . . . . . . . . . . . . . . . . . . . . . . .F13
470 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D20
471 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D20
472 . . . . . . . . . . . . . . . . . . . . . . . . . . . .D20
481 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E12
482 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E12
495 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D10
496 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D10
497 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D10
vi
500 - 599
504 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K4
513 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K1
520 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L2
521 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K1
523 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K1
524 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K2
530 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K2
535 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K2
540 . . . . . . . . . . . . . . . . . . . . . . . . .G13, K4
571 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H3
572 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H3
573 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H4
574 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H4
575 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H4
580 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H5
581 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H5
582 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H5
583 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H6
585 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H6
586 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H6
587 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H6
600 - 699
600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F16
601 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F16
602 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F16
603 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F17
618 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F14
619 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F14
620 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F14
621 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F14
622 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F15
623 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F15
624 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F15
625 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F15
626 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F16
627 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F16
650 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F17
651 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F17
652 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F17
690 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L2
691 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L2
U696 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F6
U697 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F6
698 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F6
U698 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F6
700 - 799
700 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F7
U700 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F7
701 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F7
U701 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F7
763 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F8
U763 x U700 . . . . . . . . . . . . . . . . . . . . . . .F8
764 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F8
U764 x U700 . . . . . . . . . . . . . . . . . . . . . . .F8
771 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F8
U771 x U696 . . . . . . . . . . . . . . . . . . . . . . .F8
U771 x U698 . . . . . . . . . . . . . . . . . . . . . . .F8
U771 x U700 . . . . . . . . . . . . . . . . . . . . . . .F8
774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F9
U774 x U698 . . . . . . . . . . . . . . . . . . . . . . .F9
U774 x U700 . . . . . . . . . . . . . . . . . . . . . . .F9
U774 x U701 . . . . . . . . . . . . . . . . . . . . . . .F9
780 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F5
800 - 2999
820 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G13
821 . . . . . . . . . . . . . . . . . . . . . . . . . . . .G13
927 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F18
980 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F5
990 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K8
991 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K8
992 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K8
1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J8
1001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J8
1010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J8
1011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J8
1020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J8
1021 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .J8
1401 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I1
3000 - 3099
02-3000 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3001 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3003 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3004 . . . . . . . . . . . . . . . . . . . . . . . . .F13
02-3005 . . . . . . . . . . . . . . . . . . . . . . . . .F13
02-3010 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3011 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3013 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3014 . . . . . . . . . . . . . . . . . . . . . . . . .F13
02-3015 . . . . . . . . . . . . . . . . . . . . . . . . .F13
02-3020 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3021 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3023 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3024 . . . . . . . . . . . . . . . . . . . . . . . . .F13
02-3025 . . . . . . . . . . . . . . . . . . . . . . . . .F13
02-3030 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3031 . . . . . . . . . . . . . . . . . . . . . . . . .F12
02-3033 . . . . . . . . . . . . . . . . . . . . . . . . .F12
Alphanumeric Index
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . . F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F12
. . . . . . . . . . . . . . . . . . . . . . . . .F13
. . . . . . . . . . . . . . . . . . . . . . . . .F13
02-31072 . . . . . . . . . . . . . . . . . . . . . . . .F10
02-31221 . . . . . . . . . . . . . . . . . . . . . . . .F11
02-31221U . . . . . . . . . . . . . . . . . . . . . . .F11
02-31222 . . . . . . . . . . . . . . . . . . . . . . . .F11
02-31222U . . . . . . . . . . . . . . . . . . . . . . .F11
02-31251 . . . . . . . . . . . . . . . . . . . . . . . .F11
02-31251U . . . . . . . . . . . . . . . . . . . . . . .F11
02-31252 . . . . . . . . . . . . . . . . . . . . . . . .F11
02-31252U . . . . . . . . . . . . . . . . . . . . . . .F11
3100 & 3100 Series
02-3100 . . . . . . . . . . . . . . . . . . . . . . . . . .F9
02-3101 . . . . . . . . . . . . . . . . . . . . . . . . . .F9
02-3102 . . . . . . . . . . . . . . . . . . . . . . . . .F10
02-3107 . . . . . . . . . . . . . . . . . . . . . . . . .F10
02-3107MAG . . . . . . . . . . . . . . . . . . . . .F10
02-3115 . . . . . . . . . . . . . . . . . . . . . . . . .F10
02-3122 . . . . . . . . . . . . . . . . . . . . . . . . .F11
02-3125 . . . . . . . . . . . . . . . . . . . . . . . . .F11
02-31001 . . . . . . . . . . . . . . . . . . . . . . . . .F9
02-31001U . . . . . . . . . . . . . . . . . . . . . . . .F9
02-31002 . . . . . . . . . . . . . . . . . . . . . . . . .F9
02-31011U . . . . . . . . . . . . . . . . . . . . . . . .F9
02-31012 . . . . . . . . . . . . . . . . . . . . . . . . .F9
02-31012U . . . . . . . . . . . . . . . . . . . . . . . .F9
02-31021 . . . . . . . . . . . . . . . . . . . . . . . .F10
02-31021U . . . . . . . . . . . . . . . . . . . . . . .F10
02-31022 . . . . . . . . . . . . . . . . . . . . . . . .F10
02-31022U . . . . . . . . . . . . . . . . . . . . . . .F10
8000 - 91105
8102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C1
8103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C1
8103EZ . . . . . . . . . . . . . . . . . . . . . . . . . . .C2
8105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C2
8111 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C3
8112 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C3
8113 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C4
8114 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C4
8121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C5
8190 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C5
8200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C8
8300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . C8
8302 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C9
8303 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C9
8303EZ . . . . . . . . . . . . . . . . . . . . . . . . . . .C9
8305 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C9
8311 . . . . . . . . . . . . . . . . . . . . . . . . . . . .C10
8314 . . . . . . . . . . . . . . . . . . . . . . . . . . . .C10
02-3034
02-3035
02-3040
02-3041
02-3043
02-3044
02-3045
02-3050
02-3051
02-3053
02-3054
02-3055
02-3060
02-3061
02-3063
02-3064
02-3065
02-3070
02-3071
02-3073
02-3074
02-3075
02-3080
02-3081
02-3083
02-3084
02-3085
02-3090
02-3091
02-3093
02-3094
02-3095
7000 - 7999
7212 . . . . . . . . . . . . . . . . . . . . . . . . .B5, B14
7212V . . . . . . . . . . . . . . . . . . . . . . . .B5, B14
7215 . . . . . . . . . . . . . . . . . . . . . . . .B6, B14
7215F . . . . . . . . . . . . . . . . . . . . . . . .B6, B14
7215PT . . . . . . . . . . . . . . . . . . . . . . . . . .B20
7222 . . . . . . . . . . . . . . . . . . . . . . . . .B7, B14
7226 . . . . . . . . . . . . . . . . . . . . . . . . .B8, B14
7226F . . . . . . . . . . . . . . . . . . . . . . . .B8, B14
7226PT . . . . . . . . . . . . . . . . . . . . . . . . . .B20
7227 . . . . . . . . . . . . . . . . . . . . . . . . .B9, B14
7227F . . . . . . . . . . . . . . . . . . . . . . . .B9, B14
7227PT . . . . . . . . . . . . . . . . . . . . . . . . . .B20
7230F . . . . . . . . . . . . . . . . . . . . . . .B10, B15
7237F . . . . . . . . . . . . . . . . . . . . . . .B11, B15
7244F . . . . . . . . . . . . . . . . . . . . . . .B12, B15
7245F . . . . . . . . . . . . . . . . . . . . . . .B13, B15
7253 . . . . . . . . . . . . . . . . . . . . . . . . . . .B16
7255 . . . . . . . . . . . . . . . . . . . . . . . . . . . .B17
7255J . . . . . . . . . . . . . . . . . . . . . . . . . . .B17
7256 . . . . . . . . . . . . . . . . . . . . . . . . . . . .B18
7259 . . . . . . . . . . . . . . . . . . . . . . . . . . . .B19
8400 . . . . . . . . . . . . . . . . . . . . . . . . . . . .C14
8401 . . . . . . . . . . . . . . . . . . . . . . . . . . . .C14
9010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L2
9011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9012 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . L2
9021 . . . . . . . . . . . . . . . . . . . . . . . . . . . . L3
9022 . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9031 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9032 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9033 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9040 . . . . . . . . . . . . . . . . . . . . . . . . . . . . L2
9041 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9042 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9043 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9051 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L3
9060 . . . . . . . . . . . . . . . . . . . . . . . . . . . . L4
9061 . . . . . . . . . . . . . . . . . . . . . . . . . . . . L4
9070 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L4
9071 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L4
9080 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L5
9081 . . . . . . . . . . . . . . . . . . . . . . . . . . . . L5
9090 . . . . . . . . . . . . . . . . . . . . . . . . . . . .L5
9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C6
9103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C6
9103EZ . . . . . . . . . . . . . . . . . . . . . . . . . . .C7
9110 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L5
9120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L5
9121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L5
9122 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L5
9130 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L5
9190 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C7
9210 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L6
9220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L6
9230 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L6
9240 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L6
9250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L7
9310 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L7
9311 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L7
9312 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L7
9320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L7
9321 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L7
9330 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L7
9331 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L8
9332 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L8
9333 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L8
9334 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L8
9335 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L8
9340 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L8
91105F . . . . . . . . . . . . . . . . . . . . . .B21, B22
E91105F-PT . . . . . . . . . . . . . . . . . .B21, B22
vii
Finish List
KEY TO BASE MATERIALS & PROCESS SYMBOLS
IVES MATERIAL SYMBOL
A
MA & PA
B & MB
BB
F
P
R
S
Z
MATERIAL
Aluminum
Aluminum
Brass or Bronze
Brass or Bronze
Iron or Steel
Plastic
Rubber
Stainless Steel
Zinc
PROCESS
Burnished
Polished
Polished
Burnished
Burnished
n/a
n/a
Polished
Burnished
IVES finish designations include both the U.S. Standard Finish Symbol used for many years throughout the Builders Hardware Industry and the ANSI/BHMA. Standard for Materials
and Finishes.
This cross reference of ANSI/BHMA three digit designations and the nearest U.S. Standard equivalent is provided for your convenience in selecting the product, base material
and finish required.
ANSI/BHMA STANDARD FOR MATERIALS AND FINISHES
American National Standards Institute Inc.
Builders Hardware Manufacturers Association
KEY TO FINISHES
Ives Finish No.
If other than
ANSI/BHMA
AP
A
BLK
BLK
BRN
CLR
P
R
R
T
W
505
FP or USP
2C or 2G
2G
3
4
5
9
10
10B
14
15
15A
19 or SPBLK
20A
26
26D
27
28BE
viii
ANSI/BHMA
Code
600
603
604
605
606
609
611
612
613
618
619
620
622
624
625
626
627
-
Finish Description
Aluminum, Prime Painted
Almond Epoxy Coated
Black Epoxy Coated
Black Plastic
Brown Plastic
Clear Plastic
Plastic
Rubber
Red Epoxy Coated
Teal Epoxy Coated
White Epoxy Coated
Bright Brass, Lifetime Finish
Primed for painting
Zinc plated
Zinc plated and dichromate sealed
Bright brass, clear coated
Satin brass, clear coated
Satin brass, blackened, satin relieved, clear coated
Bright bronze, clear coated
Satin bronze, clear coated
Dark oxidized satin bronze, oil rubbed
Bright nickel plated, clear coated
Satin nickel plated, clear coated
Satin nickel plated, blackened, satin relieved, clear coated
Flat Black Coated
Dark oxidized, statuary bronze, clear coated
Bright chromium plated
Satin chromium plated
Satin aluminum, clear anodizedAluminum
Etched, Black Anodized
Base Material
Aluminum
Aluminum
Aluminum
Plastic
Plastic
Plastic
Plastic
Rubber
Aluminum
Aluminum
Aluminum
Brass
Steel
Steel
Steel
Brass
Brass
Brass
Bronze
Bronze
Bronze
Brass, Bronze
Brass, Bronze
Brass, Bronze
Brass, Bronze
Bronze
Brass, Bronze
Brass, Bronze
Aluminum
Aluminum
Nearest U.S.
Equivalent
USP
US2G
US2G
US3
US4
US5
US9
US10
US10B
US14
US15
US15A
US19
US20A
US26
US26D
US27
-
Finish List
KEY TO FINISHES (continued)
Ives Finish No.
If other than
ANSI/BHMA
ANSI/BHMA
Code
Finish Description
Base Material
Nearest U.S.
Equivalent
28
32
32D
18A or SPBLK
3
4
5
10
10B
14
15
15A
20A
26
26D
3 or 3AL
4
10 or 10AL
14
15
19
26
92
USP
SPBLK
28G or 3AL
65 or SP28
69
SP10
SPBLK
628
629
630
631
632
633
638
639
640
645
646
647
650
651
652
666
667
668
669
670
671
672
673
674
676
688
689
690
691
693
Satin aluminum, clear anodized
Bright stainless steel
Satin stainless steel
Flat Black Coated
Plated bright brass, clear coated
Plated satin brass, clear coated
Plated satin brass, blackened, satin relieved, clear coated
Plated satin bronze, clear coated
Oxidized satin bronze plated over copper plate, oil rubbed
Bright nickel plated, clear coated
Satin nickel plated, clear coated
Satin nickel plated, blackened, satin relieved, clear coated
Plated dark oxidized statuary bronze, clear coated
Bright chromium plated
Satin chromium plated
Plated bright brass, clear coated
Plated satin brass, clear coated
Plated satin bronze, clear coated
Bright nickel plated
Satin nickel plated
Flat Black Coated
Bright chromium plated
Aluminum clear coated
Primed for painting
Flat Black Coated
Satin aluminum, gold anodized
Aluminum painted
Dark bronze painted
Light bronze painted
Black painted
Aluminum
Stainless steel 300 series
Stainless steel 300 series
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Zinc
Zinc
Aluminum
Any
Any
Any
Any
US28
US32
US32D
US19
US3
US4
US5
US10
US10B
US14
US15
US15A
US20A
US26
US26D
US3
US4
US10
US14
US15
US19
US26
SP313
695
Dark bronze painted
Any
63
26D
10B
SP4
313AN
315AN
4A
3A
10A
696
702
703
706
710
711
720
721
722
Satin brass painted
Satin chromium plated
Oxidized satin bronze plated, oil rubbed
Brass
Dark Bronze Anodized
Black Anodized
Mill finish, Brass, uncoated
Bright Brass, uncoated
Dark oxidized bronze, oil, rubbed
Any
Aluminum
Aluminum
USP
US19
US4
US28
US20
US10
(Black Aluminum
Hard Coat)
(Dark Bronze
Aluminum Hard Coat)
US4
US26D
US10B
Aluminum
Aluminum
Brass
Brass
Bronze
313AN
315AN
US4A
US3A
US10A
ix
Packaging, Handing
Packaging Key
Many Ives items are available in a variety of packaging forms designated by a prefix. The Ives Price Book contains the specific packaging options for each
Ives product. Below is a description of these options.
Symbol
Package
Description of Package
No prefix
Box
Standard box-packed products, polybagged or wrapped
BP
BIN-PAK
Polybagged, in a preset quantity, boxed for stocking convenience
C or CP
Carded
Skin-wrapped and blister cards
DCS
Clip Strip, Carded
Skin-wrapped and blister cards for hanging clip displays
RP
Retail Pack
Polybagged, in a convenient shelf-stocker box, in small quantity
SP
SLIM-PAK
Polybagged, in a convenient shelf-stocker box
Door Handing
LH
Left Hand
INSIDE
RH
Right Hand
OUTSIDE
INSIDE
LRB
Left Hand
Reverse Bevel
x
OUTSIDE
RRB
Right Hand
Reverse Bevel
Ives & Glynn-Johnson Product Conversions
On September 1, 2001, IR Security & Safety consolidated its Ives Commercial and Glynn-Johnson brands of accessory hardware into one powerful line
under the Ives brand name. (Glynn-Johnson now manufactures only overhead stops and push/pull latches. For more details, visit the Glynn-Johnson
web site at www.glynn-johnson.com.)
The chart below lists current model information along with their predecessors. Initially, these product conversions affected our commercial accounts.
With the 2002 Price Book 23, the conversions took effect for residential accounts as well.
Category
Description
FLUSH BOLTS
& accessories
Automatic Flush Bolts - Metal Doors
Automatic Flush Bolts - Wood Doors
Constant Latching Flush Bolts - Metal Doors
Constant Latching Flush Bolts - Wood Doors
Manual Flush Bolts
Manual Flush Bolts
Manual Flush Bolts
Manual Flush Bolts - Wood Doors
Manual Flush Bolts
Manual Flush Bolts
Manual Flush Bolts
Manual Flush Bolts
Manual Flush Bolts
Dust Proof Strikes
Dust Proof Strikes
Dust Proof Strikes
Dust Proof Strikes
Coordinators - Bar Type
Coordinators - Bar Type
Coordinators - Bar Type
Coordinators - Bar Type
Coordinators - Bar Type
Filler Bars
Filler Bars
Filler Bars
Carry Bars
Mounting Brackets
Mounting Brackets
Mounting Brackets
Mounting Brackets
Mounting Brackets
Mounting Brackets
Mounting Brackets
Mounting Brackets
Coordinators - Gravity
Coordinators - Gravity
* Watch for stop widths.
Offset and Center Hung Pivots
Pocket Pivots
Risers for Dome Stops
Dome Stops
Risers for Dome Stops
Dome Stops
Dome Stops
Dome Stops
Risers for Dome Stops
Plunger Type Door Holders
Plunger Type Door Holders
Kick Down Door Holders
Kick Down Door Holders
Kick Down Door Holders
Kick Down Door Holders
Kick Down Door Holders
Semi-Automatic Door Holders & Stops
Security Floor Stops
Security Floor Stops
COORDINATORS
& accessories
PIVOTS
FLOOR STOPS
Model Numbers
effective
September 1, 2001
Pre-September
Brand &
Model Number
Pre-September
Ives
Model Numbers
(or closest equivalent)
Pre-September
Glynn-Johnson
Model Numbers
(or closest equivalent)
FB30 Series
FB40 Series
FB50 Series
FB60 Series
FB256N
FB257N
FB258N
FB358
FB457
FB457N
FB458
FB458N
FB0458N
DP1
DP2
DP3
DP4
COR32
COR42
COR52
COR60
COR72
FL20
FL32
FL44
CB1
MB1
MB2
MB1F
MB2F
MB3F
MB1V
MB2V
MB3V
COR7G
COR9G
G-J FB30 Series
G-J FB40 Series
G-J FB50 Series
G-J FB60 Series
Ives 256
Ives 257
Ives 258
Ives 358
Ives 457
Ives 457-1/2
Ives 458
Ives 458-1/2
Ives 0458
G-J DP1
G-J DP2
G-J COR1
G-J COR1A
G-J COR2
G-J COR3
G-J COR4
G-J FB1
G-J FB2
G-J FB3
G-J CB1
G-J BX1
G-J BX2
Ives 904-1FP
Ives 904-2FP
Ives 904-3FP
Ives modifed 904-1FP
Ives modified 904-2FP
Ives modified 904-3FP
G-J COR65
G-J COR85
559
556
357
356
256
257
258
358
457
457-1/2
458
458-1/2
0458
489
489 x 487
488
488 x487
936
948
956
903-22 (various lengths)
903-34 (various lengths)
903-38 (various lengths)
478, 478-1/2
902
901
904-1FP
904-2FP
904-3FP
904-1FP
904-2FP
904-3FP
469
469-1/2
FB30 Series
FB40 Series
FB50 Series
FB60 Series
FB6W
FB6
DP1
DP2
COR1
COR1A
COR2
COR3
COR4
FB1
FB2
FB3
CB1
BX1
BX2
BX2F
BX1F*
BX1F*
BX2V
BX1V*
BX1V*
COR65
COR85
7200 Series
91105F
R435
FS436
R437
FS438
FS13
FS17
R14
FS1153
FS1154
FS452-4
FS452-5
FS455
FS544-4
FS555-5
FS9
FS18S
FS18L
G-J 7200 Series
Dor-O-Matic 91105F
Ives 435
Ives 436
Ives 437
Ives 438
G-J FB13
G-J FB17
G-J FB14R
G-J 1153M
G-J 1154
Ives 452-4"
Ives 452-5"
Ives 455
G-J 444
G-J 555
G-J F9X
G-J FB18S
G-J FB18L
435
436
437
438
452-4"
452-5"
455
-
7200 Series
FB13 & FB15
FB17
FB14R
1153M
1154
44 & 45
444
555
F9X
FB18S
FB18L
xi
Ives & Glynn-Johnson Product Conversions
Category
FLOOR STOPS
Description
Lock Guards
Floor Stops
Floor Door Stops
Floor Door Stops
Floor Door Stops
Floor Door Stops
Heavy Duty Door Stops
Heavy Duty Door Stops & Holders
Heavy Duty Door Stops
Heavy Duty Door Stops & Holders
Door Stop & Holders
Door Stop & Holders
Automatic Door Stops & Holders
Automatic Door Stops & Holders
Automatic Door Stops & Holders
Automatic Door Stops & Holders
Automatic Door Stops & Holders
Automatic Door Stops & Holders
Strikes for FS40 Series
Strikes for FS40 Series
Strikes for FS40 Series
Strikes for FS40 Series
WALL STOPS
Wall Stops
Wall Stops
Wall Stop Holders & Strikes
Wall Stops
Wall Stops
Wall Stops
Automatic Holders & Stops
Automatic Holders & Stops
Automatic Holders & Stops
Base Door Stops
Heavy Duty Wall Stops & Holders
Heavy Duty Wall Stops & Holders
Heavy Duty Wall Stops & Holders
Heavy Duty Wall Stops & Holders
Wall Bumpers
Wall Bumpers
Wall Bumpers
Wall Bumpers
Wall Bumpers
Wall Bumpers
Wall Bumpers
Wall Bumpers
Wall Bumpers
SILENCERS
Silencers
Silencers
Silencers
ROLLER BUMPERS Roller Bumpers
Roller Bumpers
Roller Bumpers
xii
Model Numbers
effective
September 1, 2001
LG14
FS434
FS441
FS441-WS
FS442
FS442-WS
FS444
FS446
FS448
FS450
FS451
FS451-WS
FS495
FS496
FS40
FS41
FS42
FS43
STK40
STK41
STK42
STK43
WS11
WS11X
WS20
WS20X
WS33
WS33X
WS40
WS45
WS45X
WS65
WS443
WS445
WS447
WS449
WS401CVX
WS401CCV
WS402CVX
WS402CCV
WS404CVX
WS406CVX
WS406CCV
WS407CVX
WS407CCV
SR64
SR65
SR66
RB470
RB471
RB472
Pre-September
Brand &
Model Number
G-J XLP12
Ives 434
Ives 441
Ives 441-WS
Ives 442
Ives 442-WS
Ives 444
Ives 446
Ives 448
Ives 450
Ives 451
Ives 451-WS
Ives 495
Ives 496
G-J F40A
G-J F41A
G-J F42A
G-J F43A
G-J F40
G-J F41
G-J F42
G-J F43
G-J WB11
G-J WB11X
G-J W20
G-J W20X
G-J WB33
G-J WB33X
G-J W40
G-J W-45A
G-J W-45AX
Ives 65
Ives 443
Ives 445
Ives 447
Ives 449
Ives 401
Ives 401-1/2
Ives 402
Ives 402-1/2
Ives 404
Ives 406
Ives 406-1/2
Ives 407
Ives 407-1/2
GJ 64
GJ 65
GJ 66
Ives 470
Ives 471
Ives 472
Pre-September
Ives
Model Numbers
(or closest equivalent)
434
441
441-WS
442
442-WS
444
446
448
450
451
451-WS
495
496
65
443
445
447
449
401
401-1/2
402
402-1/2
404
406
406-1/2
407
407-1/2
20R
21R
470
471
472
Pre-September
Glynn-Johnson
Model Numbers
(or closest equivalent)
XLP12
FB19X
FB19
FB36
F-26
F20X
F20
F40A
F41A
F42A
F43A
F40
F41
F42
F43
WB11
WB11X
W20
W20X
WB33
WB33X
W40
W-45A
W-45AX
W-27
WB35
50C-Wood Screws
60C-Wood Screws
50C
60C
25C
50W-Wood Screws
60W-Wood Screws
50W
60W
64
65
66
RB3
RB4
RB6
Ives & Glynn-Johnson Product Conversions
Category
CRASH STOPS
HAND RAIL
BRACKETS
LOCK GUARDS
Description
LATCHES
Invisible Latches
Auxiliary Pushers
Ball Type Door or Cabinet Latches
Ball Type Door or Cabinet Latches
Ball Type Door or Cabinet Latches
Roller Latches
Roller Latches
Roller Latches
Roller Latches
Roller Latches
Roller Latches
Roller Latches
Strikes for Roller Latch
Strikes for Roller Latch
Strikes for Roller Latch
Applied Stops
Applied Stops
Crash Stops
Crash Stops
Crash Stops
Hand Rail Brackets
Lock Guards
Lock Guards
Lock Guards
Lock Guards
Lock Guards
Lock Guards
Lock Guards
Lock Guards
Lock Guards
Lock Guards
Lock Guards
Lock Guards
SURFACE BOLTS 8" Steel Surface Bolts - Bottom
8" Steel Surface Bolts - Top
8" Steel Surface Bolts - Top & Btm Strikes
8" Steel Surface Bolts - Locking Bottom
8" Steel Surface Bolts - Locking Top
8" Steel Surface Bolts - Locking, Top & Btm
8" Brasss Surface Bolts - Bottom
8" Brasss Surface Bolts - Top
8" Brasss Surface Bolts - Locking Bottom
8" Brasss Surface Bolts - Locking Top
12" and 24" Heavy Duty Surface Bolts
12" and 24" Heavy Duty Surface Bolts
Heavy Duty Surface Bolts
Heavy Duty Surface Bolts
Heavy Duty Surface Bolts
Heavy Duty Surface Bolts
Security Surface Bolts - Top Strike
Security Surface Bolts - Top & Btm Strikes
Security Surface Bolts - Top Strike
Security Surface Bolts - Top & Btm Strikes
Security Surface Bolts - Top & Btm Strikes
ARCHITECTURAL Pulls, Push Plates, Pull Plate, Kick Plates,
DOOR TRIM
Mop Plates, Armor Plates
Model Numbers
effective
September 1, 2001
Invisible Latches
CL12
CL14
CL21
CL21A
CL22
RL30
RL30F
RL32
RL32F
RL36
RL38
RL1152
STK726
STK685
STK685L
AS18
AS895
CS115-20
CS115-25
CS115-30
HB158
HB159A, HB159B
HB162
LG1-US32D
LG1-US2G
LG1-USP
LG1-SP313
LG1-US4
LG1-US10
LG7
LG10
LG11
LG12
LG13
LG14
SB1630B
SB1630T
SB1630TB
SB1630BL
SB1630TL
SB1630TBL
SB1640B
SB1640T
SB1640BL
SB1630TL
SB360-12-T
SB360-24-T
SB453-8-TB
SB453-12-TB
SB453-18-TB
SB453-24-TB
SB0454-5-T
SB0454-8-TB
SB454-5-T
SB454-8-T
SB454-12-TB
Pre-September
Brand &
Model Number
CL11
G-J BB
G-J AP-2
G-J 21
G-J 21A
G-J 22
G-J 30
G-J 30F
G-J 32
G-J 32F
G-J 36
G-J 38
G-J SK1152B
G-J SK726
G-J SK685
G-J SK685L
G-J SP-18
G-J SK895
Ives 115 20-1/2
Ives 115 25-1/2
Ives 115 30-1/2
Ives 158
Ives 159
Ives 162
G-J LP1
G-J LP2
G-J LP3
G-J LP4
G-J LP5
G-J LP6
G-J XLP7
G-J LP10
G-J LP11
G-J LP12
G-J LP13
G-J XLP12
G-J 1631
G-J 1632
G-J 1651
G-J 1631L
G-J 1632L
G-J 1651L
G-J 1641
G-J 1642
G-J 1641L
G-J 1642L
Ives 360 12"
Ives 360 24"
Ives 453 - 8"
Ives 453 - 12"
Ives 453 - 18"
Ives 453 - 24"
Ives 0454 5"
Ives 0454 8"
Ives 454 5"
Ives 454 8"
Ives 454 12"
Pre-September
Ives
Model Numbers
(or closest equivalent)
G-J AA
115 20-1/2
115 25-1/2
115 30-1/2
158
159
162
180
182
184
361-8-MS
361-8-US
360 12"
360 24"
453 - 8"
453 - 12"
453 - 18"
453 - 24"
0454 5"
0454 8"
454 5"
454 8"
454 12"
Pre-September
Glynn-Johnson
Model Numbers
(or closest equivalent)
AA
BB
AP-2
21
21A
22
30
30F
32
32F
36
38
SK1152B
SK726
SK685
SK685L
SP-18
SK895
LP1
LP2
LP3
LP4
LP5
LP6
XLP7
LP10
LP11
LP12
LP13
XLP12
1631
1632
1651
1631L
1632L
1651L
1641
1642
1641L
1642L
1708TB
1712TB
-
8000 Series
Ives 8000 Series
8000 Series
--
xiii
Notes
xiv
Ives & Glynn-Johnson Product Conversions
xv
Notes
xvi
Section A
Flush Bolts and
Coordinators
Automatic Flush Bolts - Metal Doors
FB30 Series for Metal Doors
• Fully Automatic—inactive door is latched when active door closes,
bolts retract when active door is opened.
• Low Actuation Forces—Top Bolt Has No Spring Tension.
• UL Listed for Fire Doors.
• Fits standard ANSI A115.4 Door Frame Preparations.
• Non-handed.
• Models with Auxiliary Fire Latch eliminates the bottom bolt
and is UL Listed for Fire Doors.
• Finishes: US3, US4, US10, US10B, US32, US32D.
• Finished Cover Plates permit finish changes in stock or at job site.
• Bolts have 3/4" throw with a 7/8" vertical adjustment.
• Standard Rod Length is 12", which is measured from the center
of the flush bolt body to the bolt tip.
• Meets ANSI A156.3 Type 25.
• Optional Dust Proof Strikes—DP1 or DP2, prevents
dirt build-up assuring full engagement of bottom bolt.
• Optional rod lengths available for top bolt for non-fire rated
openings—18", 24", 36" and 48".
FB31P Pair
FB32
FB33
FB31T
FB31B
Top and Bottom Bolts
Top Bolt with
Auxiliary Fire Latch
Top Bolt with
Auxiliary Fire Latch
and Retrofit Plate
Top Bolt Only
Bottom Bolt Only
Both bolts are nonhanded, but are not
identical. The top bolt
has no spring tension,
resulting in lower
actuation force with a
smoother operation.
• UL Listed 3 hours on
8'0" x 10'0" Opening
FB32 combination
includes FB31T Top Bolt
with auxiliary fire latch.
Provides a fire-listed
application without a
bottom bolt— meaning
no floor prep and strike.
The auxiliary fire latch,
mounted in the door edge,
releases under extremely high temperatures to
keep the doors in
alignment during a fire.
• UL Listed 3 hours on
8'0" x 8'0" Opening
FB33 used to update
existing flush bolt
installations with
auxiliary fire latch
eliminating bottom bolt
and floor strike. FB33
consists of FB31T Top
Bolt, auxiliary Fire Latch
and Filler plate to cover
existing cutout when
bottom bolt is removed.
• UL Listed 3 hours on
8'0" x 8'0" Opening
Dimensions:
Body Size: 1" Wide x 6-3/4" Long x 2" Deep
Guide Size: 1" Wide x 1-27/32" Long x 27/32" High x 3/32" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick
Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick
Auxiliary Fire Latch Size: 1" Wide x 1-3/4" Long x 3-1/4" Deep
Filler Plate Size: 1" Wide x 6-3/4" Long x 3/32" Thick
A1
Automatic Flush Bolts - Wood Doors
FB40 Series for Wood Doors
• Fully Automatic—inactive door is latched when active door closes,
bolts retract when active door is opened.
• Low Actuation Forces—Top Bolt Has No Spring Tension.
• UL Listed for Fire Doors.
• Non-handed.
• Models with Auxiliary Fire Latch eliminates the Bottom Bolt and
is UL Listed for Fire Doors.
• Finishes: US3, US4, US10, US10B, US32, US32D.
• Finished Cover Plates permit finish changes in stock or at job site.
• Bolts have 3/4" throw with a 7/8" vertical adjustment.
• Meets ANSI A156.3 Type 25.
• Optional Dust Proof Strikes—DP1 or DP2, prevents
dirt build-up assuring full engagement of bottom bolt.
FB41P Pair
FB42
FB41T
FB41B
Top and Bottom Bolts
Top Bolt with
Auxiliary Fire Latch
Top Bolt Only
Bottom Bolt Only
Both bolts are non-handed,
but are not identical. The
top bolt has no spring
tension, resulting in
lower actuation force
with a smoother operation.
• UL Listed 90 minutes on
8'0" x 8'0" Opening
FB42 combination includes
FB41T Top Bolt with auxiliary
fire latch. Provides a fire-listed
application without a bottom
bolt— meaning no floor prep
for strike. The auxiliary fire
latch, mounted in the door
edge, releases under extremely
high temperatures to keep the
doors in alignment during a fire.
• UL Listed 20 minutes on
8'0" x 8'0" Opening
Dimensions:
Body Size: 1" Wide x 8-1/2" Long x 2" Deep
Guide Size: 1" Wide x 6" Long x 1/8" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick
Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick
Auxiliary Fire Latch Size: 1" Wide x 1-3/4" Long x 3-1/4" Deep
A2
Constant Latching Flush Bolts - Metal Doors
FB50 Series for Metal Doors
• Constant Latching—inactive door remains latched until
the active door is opened, releasing the automatic bottom
bolt and then the top bolt can be manually released.
Inactive door will relatch automatically when closed.
• Low Actuation Forces.
• UL Listed for Fire Doors.
• Fits standard ANSI A115.4 Door and Frame Preparations.
• Non-handed.
• Models with Auxiliary Fire Latch eliminates the bottom bolt
and is UL Listed for Fire Doors.
•
•
•
•
•
Finishes: US3, US4, US10, US10B, US32, US32D.
Finished Cover Plates permit finish changes in stock or at job site.
Bolts have 3/4" throw with a 7/8" vertical adjustment.
Meets ANSI A156.3 Type 27.
Standard Rod Length is 12", which is measured from the center
of the flush bolt body to the bolt tip.
• Optional Dust Proof Strikes—DP1 or DP2, prevents dirt build-up
assuring full engagement of bottom bolt.
• Optional rod lengths available for top bolt for non-fire rated
openings—18", 24", 36" and 48".
FB51P Pair
FB52
FB53
FB51T
Top and Bottom Bolts
Top Bolt with
Auxiliary Fire Latch
Top Bolt with Auxiliary Fire
Latch and Retrofit Plate
Top Bolt Only
FB52 combination includes
FB51T Top Bolt with auxiliary
fire latch. Provides a fire-listed
application without a bottom
bolt—meaning no floor prep for
strike. The auxiliary fire latch,
mounted in the door edge,
releases under extremely high
temperatures to keep the doors
in alignment during a fire.
FB53 used to update existing
flush bolt installations with
auxiliary fire latch eliminating
bottom bolt and floor strike.
FB53 consists of FB51T top
bolt, auxiliary fire latch and
filler plate to cover existing
cutout when bottom bolt is
removed.
• UL Listed 3 hours on
8'0" x 8'0" Opening.
• UL Listed 3 hours on
8'0" x 8'0" Opening.
FB51P combines FB51T
constant latching top bolt
with FB31B automatic
bottom bolt. Non-handed.
• UL Listed 3 hours on
8'0" x 10'0" Opening.
Dimensions:
Body Size: 1" Wide x 6-3/4" Long x 2" Deep
Guide Size: 1" Wide x 1-27/32" Long x 11/16" High x 3/32" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick
Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick
Auxiliary Fire Latch Size: 1" Wide x 1-3⁄4" Long x 3-1/4" Deep
Filler Plate Size: 1" Wide x 6-3/4" Long x 3/32" Thick
A3
Constant Latching Flush Bolts - Wood Doors
FB60 Series for Wood Doors
• Constant Latching—inactive door remains latched until the
active door is opened, releasing the automatic bottom bolt and
then the top bolt can be manually released. Inactive door will
relatch automatically when door closes.
• Low Actuation Forces.
• UL Listed for Fire Doors.
• Non-handed.
• Models with Auxiliary Fire Latch eliminates the bottom bolt
and is UL Listed for Fire Doors.
• Finishes: US3, US4, US10, US10B, US32, US32D.
• Finished Cover Plates permit finish changes in stock or at job site.
• Bolts have 3/4" throw with a 7/8" vertical adjustment.
• Meets ANSI A156.3 Type 27.
• Optional Dust Proof Strikes—DP1 or DP2, prevents
dirt build-up assuring full engagement of bottom bolt.
FB61P Pair
FB62
FB61T
Top and Bottom Bolts
Top Bolt with
Auxiliary Fire Latch
Top Bolt Only
FB61P combines FB61T constant
latching top bolt with FB41B bottom bolt.
• UL Listed 90 minutes on
8'0" x 8'0" Opening
FB62 combination includes FB61T top bolt
with Auxiliary Fire Latch. Provides
a fire-listed application without a bottom
bolt—meaning no floor prep for strike.
The Auxiliary Fire Latch, mounted in the
door edge, releases under extremely
high temperatures to keep the doors
in alignment during a fire.
• UL Listed 20 minutes on
8'0" x 8'0" Opening
Dimensions:
Body Size: 1" Wide x 8-1/2" Long x 2" Deep
Guide Size: 1" Wide x 6" Long x 1/8" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick
Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick
Auxiliary Fire Latch Size: 1" Wide x 1-3/4" Long x 3-1/4" Deep
A4
Manual Flush Bolts - Metal Doors
FB256N, FB257N, and FB258N
Series for Metal Doors
• When the active door is opened, the lever can be moved to the ‘up’
position, retracting the bolt and allowing the inactive leaf to be
opened. When the inactive leaf is closed, the lever can be moved to
the ‘down’ position, projecting the bolt into the strike and securely
locking the inactive leaf.
• Simplified installation in metal frames. Round bolt head requires
only a punched hole. Use of strike optional. Special design of guide
and flat sided bolt tip to prevent bolt rotation.
• Non-handed.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D
• Bolt tip is 1/2" Diameter.
• Bolts have 3/4" throw with a bolt backset of 3/4".
• Standard Rod Length is 12", which is measured from the center
of the flush bolt body to the bolt tip.
• Meets ANSI/BHMA A156.16, L04251.
• Optional Dust Proof Strikes — prevents dirt build-up assuring full
engagement of bottom bolt.
• Optional rod lengths available: 6", 9", 18", 24", 30", 36" and 48".
D
E
U
N
I
T
N
O
C
DIS
FB256N
FB257N
FB258N
Top or Bottom Bolt
Top or Bottom Bolt
Top or Bottom Bolt
Dimensions:
Body Size: FB256N: 3/4" Wide x 6-3/8" Long x 1-1/8" Deep
FB257N: 1-1/4" Wide x 6-3/8" Long x 1-1/8" Deep
FB258N: 1" Wide x 6-3/8" Long x 1-1/8" Deep
Guide Size: 1" Wide x 2" Long x 5/64" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick
A5
Manual Flush Bolts - Wood Doors
FB358 Series for Wood Doors
• When the active door is opened, the lever can be moved to the
‘up’ position, retracting the bolt and allowing the inactive leaf to be
opened. When the inactive leaf is closed, the lever can be moved to
the ‘down’ position, projecting the bolt into the strike and securely
locking the inactive leaf.
• Reduces installation costs; requires only simple router mortise
at top and bottom corners of doors.
• Door strength and rigidity maintained by tying door faces to
reinforcing extensions on guide with machine screws and
bearing washers.
FB358
Top or Bottom Bolts
• UL Listed 90 minutes on 8'0" x 10'0" Opening
Dimensions:
Body Size: 1" Wide x 6-3/4" Long x 1-3/8" Deep
Guide Size: 1" Wide x 2-1/2" Long x 5/64" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick
A6
•
•
•
•
•
•
UL Listed for Fire Doors.
Non-handed.
Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
Bolts have 3/4" throw with a 7/8" vertical adjustment.
Meets ANSI/BHMA A156.16, L04261.
Optional Dust Proof Strikes—DP1 or DP2, prevents dirt
build-up assuring full engagement of bottom bolt.
• Not available for rabbeted door installations.
Manual Flush Bolts - Metal Doors
FB457 and FB457N Series for Metal Doors
• When the active door is opened, the lever can be moved to the
‘up’ position, retracting the bolt and allowing the inactive leaf to be
opened. When the inactive leaf is closed, the lever can be moved to
the ‘down’ position, projecting the bolt into the strike and securely
locking the inactive leaf.
• Simplified installation in metal frames. Round bolt head requires
only a punched hole. Use of strike optional. Special design of guide
and flat sided bolt tip to prevent bolt rotation.
• Non-handed.
• FB457 UL Listed for Fire Doors.
• FB457N not UL Listed for Fire Doors.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26,
B26D.
• Bolt tip is 1/2" Diameter.
• Bolts have 3/4" throw with a bolt backset of 3/4".
• Standard Rod Length is 12", which is measured from the center
of the flush bolt body to the bolt tip.
• Meets ANSI/BHMA A156.16, L04251.
• Optional Dust Proof Strikes — prevents dirt build-up assuring full
engagement of bottom bolt.
• Optional rod lengths available for FB457: 6", 9", 18" and 24".
• Optional rod lengths available for FB457N: 6", 9", 18", 24", 30",
36" and 48".
FB457
FB457N
Top or Bottom Bolt
Top or Bottom Bolt
• UL Listed 3 hours on 8'0" x 10'0" Opening
Dimensions:
Body Size: 1-1/4" Wide x 6-3/4" Long x 1-1/8" Deep
Guide Size: 1" Wide x 2" Long x 5/64" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick
A7
Manual Flush Bolts - Metal Doors
FB458, FB458N and FB0458N
Series for Metal Doors
• When the active door is opened, the lever can be moved to the ‘up’
position, retracting the bolt and allowing the inactive leaf to be
opened. When the inactive leaf is closed, the lever can be moved to
the ‘down’ position, projecting the bolt into the strike and securely
locking the inactive leaf.
• Simplified installation in metal frames. Round bolt head requires
only a punched hole. Use of strike optional. Special design of guide
and flat sided bolt tip to prevent bolt rotation.
• FB458 UL Listed for Fire Doors.
• FB458N and FB0458N not UL Listed for Fire Doors.
• FB0458N features 1/4" radius corners on body.
• Non-handed.
•
•
•
•
•
•
•
•
Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
Bolt tip is 1/2" diameter.
Bolts have 3/4" throw with a bolt backset of 3/4".
Standard Rod Length is 12", which is measured from the center
of the flush bolt body to the bolt tip.
Meets ANSI/BHMA A156.16, L04251.
Optional Dust Proof Strikes— prevents dirt build-up assuring full
engagement of bottom bolt.
Optional Rod Lengths available for FB458: 6", 9", 18" and 24".
Optional Rod Lengths available for FB458N and FB0458N: 6", 9", 18",
24", 30", 36" and 48".
FB458
FB458N
FB0458N
Top or Bottom Bolt
Top or Bottom Bolt
Top or Bottom Bolt
• UL Listed 3 hours on
8'0" x 10'0" Opening
Dimensions:
Body Size: 1" Wide x 6-3/4" Long x 1-1/8" Deep
Guide Size: 1" Wide x 2" Long x 5/64" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick
A8
Dust Proof Strikes
DP1 and DP2 Dust Proof Strikes
• Designed for use with the bottom bolt of all flush bolts.
• Spring-loaded plunger returns to floor or threshold level
anytime flush bolt is retracted, eliminating need to clean
standard floor strikes.
• Meets ANSI/BHMA 156.16, L14011.
• Finishes: US3, US4, US10, US10B, US26, US26D.
Dimensions:
DP1 Face Plate: 1-7/16" Diameter
DP2 Face Plate: 1-5/8" Wide x 3-1/2" Long x 1/8" Thick
DP1 and DP2 Body: 1-3/16" Diameter x 1-7/8" Deep
DP1
DP2
Threshold only.
Floor and/or threshold.
DP3 and DP4 Dust Proof Strikes
• Designed for use with the bottom bolt of the Ives extension flush
bolts on non-fire rated openings. DP3 for installation in thresholds
up to 1/4" thick. DP4 includes plate for installation in thresholds
or floor.
• 3/4" diameter plunger accepts up to 5/8" diameter round bolts or
1/2" square bolts.
• Can be locked in up position by rotating plunger with screwdriver
or coin. Eliminates trapping of spiked heels.
• Made from polished wrought brass.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
DP3
Threshold only.
Dimensions:
DP3 Faceplate: 1-3/8" Diameter
DP4 Faceplate: 1-5/8" Wide x 3-1/2" Long x 1/8" thick
DP3 and DP4 Body: 1-61/64" Overall Depth, Fits Hole
1-1/16" in Diameter
D
E
U
N
I
T
N
O
C
DIS
DP4
Floor and/or threshold.
A9
Manual Flush Bolts
260 Series
261 Series
• Designed with face plate rounded for simple, one-step router
installation.
• Steel bolt head in nylon bushing combined with dual action spring
lock to hold bolt projected or retracted provides easy, one-finger
operation.
• Economically priced for the volume builder.
• Made from polished wrought brass.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
• An exceptionally smooth working flush bolt with sharp, crisp lines.
• Double action spring design provides automatic holding of brass
bolt in projected or retracted position, and assures ease of
operation in conjunction with deep cup finger hole.
• Made from polished cast brass.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
Body Size: 3/4" Wide x 4" Long x 1-1/8" Deep
Strike Size: 5/8" Wide x 1-1/2" Long
Rod Backset: 15/32"
Diameter of Bolt Head: 5/16"
Throw: 3/4"
Dimensions:
Body Size: 3/4" Wide x 6-3/4" Long x 5/8" Deep
Strike Size: 5/8" Wide x 1-1/2" Long
Rod Backset: 3/8"
Diameter of Bolt Head: 5/16"
Throw: 3/4"
262 Series
263 Series
• An exceptionally smooth working flush bolt with sharp, crisp lines.
• Double action spring design provides automatic holding of brass
bolt in projected or retracted position, and assures ease of
operation in conjunction with deep cup finger hole.
• Made from polished cast brass.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
• A compact flush bolt designed specifically for easy, low cost
installation.
• Rounded faceplate and lip for simplified installation.
• Double action spring design provides automatic holding of brass
bolt in projected or retracted position, and assures ease of
operation in conjunction with deep cup finger hole.
• Made from polished cast brass.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
Body Size: 3/4" Wide x 6" Long x 1-11/32" Deep
Strike Size: 7/8" Wide x 1-3/4" Long
Rod Backset: 15/32"
Diameter of Bolt Head: 1/2"
Throw: 1"
A10
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Body Size: 3/4" Wide x 5" Long x 1-1/2" Deep
Strike Size: 5/8" Wide x 1-1/2" Long
Rod Backset: 15/32"
Diameter of Bolt Head: 5/16"
Throw: 3/4"
Manual Flush Bolts
264 Series
265 Series
• A compact flush bolt designed specifically for fast, low cost
installation.
• Same rounded faceplate and lip as the 263 Flush Bolt for
simplified installation.
• Extra long lip permits installation in a variety of door contraction designs
• Double action spring design provides automatic holding of brass
bolt in projected or retracted position, and assures ease of
operation in conjunction with deep cup finger hole.
• Made from polished cast brass.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D
• A flush bolt with radiused bottom faceplate designed specifically
for simple one-step router installation.
• Double action spring design provides automatic holding of brass
bolt in projected or retracted position, and assures ease of
operation in conjunction with deep cup finger hole.
• Faceplate is polished solid brass; bolt is made from aluminum zinc
alloy.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
D
E
U
TIN
N
O
C
S
DI
Dimensions:
Body Size: 3/4" Wide x 4-1/2" Long x 1-3/4" Deep
Strike Size: 5/8" Wide x 1-1/2" Long
Rod Backset: 15/32"
Diameter of Bolt Head: 5/16"
Throw: 3/4"
Dimensions:
Body Size: 3/4" Wide x 6" Long x 1-7/16" Deep
Strike Size: 7/8" Wide x 1-3/4" Long
Rod Backset: 1/2"
Diameter of Bolt Head: 1/2"
Throw: 1"
266 Series
• Same as the 265 Flush Bolt except with square bottom faceplate.
• Double action spring design provides automatic holding of brass
bolt in projected or retracted position, and assures ease of
operation in conjunction with deep cup finger hole.
• Faceplate is polished solid brass; bolt is made from aluminum zinc
alloy.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
Body Size: 3/4" Wide x 6" Long x 1-7/16" Deep
Strike Size: 7/8" Wide x 1-3/4" Long
Rod Backset: 1/2"
Diameter of Bolt Head: 1/2"
Throw: 1"
A11
Coordinators - Bar Coordinators and Filler Bars
COR Series Bar Coordinators
• The COR Series Coordinators are designed for use on pairs of
doors when one door needs to close before the other.
• All COR units function easily. The active door lever, located nearest
to the active stop, holds the active door open until the trigger
mechanism is released by the closing of the inactive leaf.
• All COR units are equipped with an override feature which allows
the active door to close under extreme pressure.
• All COR units are compatible with Flush Bolts.
• The COR Series is available in five sizes for variable
door opening widths.
• The COR Series does not cover the entire length of the stop, so a
filler bar can be provided to maintain architecturally clean lines.
• COR Series Coordinator Channels and fillers are made of aluminum
and are normally furnished in a US28 finish. Also available in
US26D, and 315AN (Black).
• Meets ANSI/BHMA A156.3, Type 21A.
• UL Listed for installation on labeled frame.
• Optional Filler Bars: FL20, FL32 and FL44, available to maintain
clean line.
• Optional Mounting Brackets available: MB1, MB2, MB1F, MB2F,
MB3F, MB1V, MB2V, and MB3V for other stop applied hardware.
For Openings Where Doors Are Same Size
Coordinator
Number
Length of
Channel
For Opening
Widths
Common
Applications
32"
42"
52"
60"
72"
34" - 52"
52" - 72"
62" - 92"
70" - 108"
84" - 132"
Pair of 2'0" Doors
Pair of 2'6" Doors
Pair of 3'0" Doors
Pair of 3'6" Doors
Pair of 4'0" Doors
COR32
COR42
COR52
COR60
COR72
For Openings Where Doors Are Unequal Size
The coordinator length should equal the active door width plus approximately 1/2 the
inactive door width. The coordinator must be 6" longer than the active door width and
shorter than the overall frame opening between stops.
Dimensions: 1-5/8" Wide x 5/8" Deep x Ordered Length
FL Series Filler Bars
• The FL Filler Bars are available in three sizes for variable frame openings.
• FL Filler Bars are made of aluminum and are normally furnished
in a US28 finish. Also available in US26D and 315AN (Black).
• FL Filler Bars are field sized to frame opening.
Filler Bar Number
FL20
FL32
FL44
Length
20"
32"
44"
Dimensions: 1-5/8" Wide x 5/8" Deep x Ordered Length
A12
Coordinators - Mounting Brackets
Mounting Brackets
MB1 and MB2
• Allows stop mounted hardware to be properly installed without
damaging the COR coordinator, such as a parallel arm closer or
a non-fire-rated surface vertical rod strike.
• Stop mounted hardware will need to be lowered to compensate
for the height of the coordinator and mounting bracket.
• MB mounting brackets are made of aluminum and normally
furnished in a USP finish. Powder Coated Finishes: SP28 and
SPBLK.
MB1
Product
MB1
MB2
MB2
Jamb Depth
Stop Width
4-3/4" Min.
4-3/4" Min.
Over 2-1/2"
Up to 2-1/2"
Dimensions:
MB1: 4" Wide x 3" Deep x 15/16" Tall
MB2: 4" Wide x 3-1/4" Deep x 1-5/8" Tall
MB1F, MB2F and MB3F
• Allows stop mounted hardware to be properly installed without
damaging the COR coordinator. Example: strike for fire-rated
surface vertical rod exit device.
• Stop mounted hardware will need to be lowered to compensate
for the height of the coordinator and mounting bracket.
• MBF mounting brackets are made of 3/8" thick steel and
normally furnished in a USP finish. Powder Coated Finishes: SP28
and SPBLK.
MB1F
Product
MB1F
MB2F
MB3F
MB2F
MB3F
Jamb Depth
Stop Width
5" Min.
5-7/8" Min.
6-7/8" Min.
1-1/2" to 2-1/4"
2-3/8" to 3-1/4"
3-3/8" and Wider
Dimensions:
MB1F: 4" Wide x 3" Deep x 1-5/8" Tall
MB2F: 4" Wide x 4" Deep x 1-5/8" Tall
MB3F: 4" Wide x 3-1/2" Deep x 1" Tall
MB1V, MB2V and MB3V (not shown)
Same as MB1F, MB2F and MB3F with factory preparation for the
Von Duprin 8827-F soffit latch.
A13
Coordinators
Special Factory Preparation for
Use with Vertical Rod Exit Devices
• Coordinators may need to be prepared at the factory for use
with some surface and concealed vertical rod exit devices.
(See Chart below)
• If exit device not listed in chart, the information shown on
the illustration will be needed.
1. Exit Device Manufacturer and Model No.
2. Active Net Door Size, “X”
3. Inactive Net Door Size, “Y”
4. Exit Device Backset, “U”
5. Stop Width, “W”
6. Stop Thickness if other than 5/8", “V”
Exit Device
Manufacturer
Exit Device
Number
Device
Backset
Maximum
Active Door
Coordinator
Size Needed
Coordinator
Cutout Type
Mounting Bracket
Needed
Von Duprin
5547-F
2-3/8"
None
8827-F
2-3/4"
B
MB1V, MB2V
or MB3V
Von Duprin
8847-F
2-3/8"
C
None
Von Duprin
33/3547
33/3547-F
98/9947
98/9947-F
33/3548
33/3548-F
98/9948
98/9948-F
33/3547WDC
33/3547WDC-F
98/9947WDC
98/9947WDC-F
17-C
F-17-C
18-C
F-18-C
XX-C
F-XX-C
17-C-WDC
F-17-C-WDC
18-C-WDC
F-18-C-WDC
XX-C-WDC
F-XX-C-WDC
2-3/4"
42"
52"
60"
72"
42"
52"
60"
72"
42"
52"
60"
72"
42"
52"
60"
72"
42"
52"
60"
72"
42"
52"
60"
72"
42"
52"
60"
72"
A
Von Duprin
33"
43"
51"
63"
33"
43"
51"
63"
33"
43"
51"
63"
33"
43"
51"
64"
33"
43"
51"
64"
34"
44"
52"
65"
33"
43"
51"
63"
D
None
D
None
E
None
F
None
33"
43"
51"
63"
42"
52"
60"
72"
G
None
Von Duprin
Von Duprin
Monarch
Monarch
A14
2-3/4"
1-5/16"
2-3/4"
2-13/16"
Ordering Guide for Bar Coordinators
How to Order COR and Accessories
COR
52
__
-
US28
____
-
FL20
____
D
__
-
36"
__ -
-
2-MB2
_____
COR Size:
32, 42, 52, 60, 72
Finishes:
US28, US26D, 315AN (Black)
Filler Bar (if desired):
FL20, FL32, FL44
Vertical Rod Exit Device Cutout Type (if applicable):
A, B, C, D, E, F, G
If other Vertical Rod Exit Device not listed on chart, from page A14,
include information as shown on page A14.
Net Active Door Size – Required for ALL Vertical Rod Exit Device Applications
Mounting Bracket:
Indicate quantity, then bracket. MB1, MB2, MB1F, MB2F, MB3F, MB1V, MB2V, MB3V
Mounting brackets are sold and packaged separately from coordinators.
X
To determine the size COR you need:
1. Start with the active door size (X).
2. Next consider the overall frame opening between stops (F).
3. Preferably, the coordinator would equal the active door
width (X) + approximately 1/2 inactive door width (Y).
Keep in mind the coordinator must be 6" longer than
the active door width (X) and less than the overall frame
opening between stop (F).
ACTIVE DOOR
WIDTH
Y
INACTIVE DOOR
WIDTH
INACTIVE LEAF
ACTIVE LEAF
W
COORDINATOR
STOP WIDTH
F
V
STOP THICKNESS
Examples:
• Pair of 30" Doors, 5/8" Stops
Active Door Size, X = 30"
Overall Frame Opening between Stops, F = 58-3/4"
Recommended Coordinator: COR42
• 36" Active Door, 18" Inactive door, 5/8" Stops
Active Door Size, X = 36"
Overall Frame Opening between Stops, F = 52-3/4"
Recommended Coordinator: COR42
• Pair of 36" Doors, 5/8" Stops
Active Door Size, X = 36"
Overall Frame Opening between Stops, F = 70-3/4"
Recommended Coordinator: COR52
• 48" Active Door, 24" Inactive Door, 5/8" Stops
Active Door Size, X = 48"
Overall Frame Opening between Stops, F = 94-3/4"
Recommended Coordinator: COR60
A15
Coordinators - Gravity Coordinators
COR7G and COR9G
Gravity Coordinators
Features:
• When active door is open, coordinator prevents active door
from closing until inactive door bypasses. Closing of inactive
door causes strike plate on top of door to contact cam and lift
arm, allowing active door to close. As inactive door continues
closing, roller rides over strike plate on to door bracket, holding
arm above active door.
• UL Listed for Fire Doors.
• Non-handed.
• Gravity action arm and door bracket are adjustable on the job
for ease of installation. Nylon roller provides quiet and efficient
operation, and helps protect the astragal and doors from damage.
• Nylon roller on short arm glides smoothly over door bracket
and strike, ensuring silent operation.
• Made of forged brass.
• Finishes: US3, US4, US10, US10B, US26, US26D.
• Meets ANSI/BHMA A156.3, Type 21.
CB1 Carry Bar
Features:
• Used when it is possible for the inactive door
to be opened before the active door.
• Prevents damage to the doors and other hardware.
• Nylon roller insures quiet and efficient operation.
• Non-handed.
• All-steel construction.
• Finishes: USP, US3, US4, US10, US10B, US26, US26D.
• Meets ANSI/BHMA A156.3, Type 21.
• Standard sex bolts for mounting.
A16
CORG7
7" Projection
• Use on pairs of doors with astragal on active door up to 4'.
• With astragal, inactive door up to 3'4".
• With astragals, both doors up to 2'10".
CORG9
9" Projection
• Use on pairs of doors with astragal on active door over 4'.
• With astragal, inactive door over 3'4".
• With astragals, both doors over 2'10".
Section B
Pivots
7200 Series Pivots
General Information:
• Complete line of 3/4" offset, 1-1/2" offset, center hung,
intermediate and power transfer pivots with all exposed parts
made of brass or stainless steel for maximum corrosion resistance.
• High strength brass and stainless steel forgings, and castings
for rated and non-rated doors combined with precision bearings
for smooth operation.
• Stainless steel machine screws and wood screws standard.
• Positive locking vertical adjustment mechanism allows the installer
to precisely position the door and balance the load.
• Last digit in pivot set number reflects the maximum door
weight in hundreds of pound, e.g., 7215 = 500 pounds. For
sets designated as “heavy duty”, add 1,000 pounds, e.g.,
7237F HD set = 1700 pounds.
• Pivots for lead lined doors are available, consult factory.
• See page B4 for Pivot Selection Chart.
Finishes:
Description
Finish
BHMA
Powder-Coated Finishes (Available on all models)
Aluminum
Black
Dark Bronze
Brass
Bronze
SP28
SPBLK
SP313
SP4
SP10
689
622
695
706
691
Plated Finishes (Available on all models except “F—Fire-Rated” models)
Polished Brass
Satin Brass
Satin Bronze
Oil-Rubbed Bronze
Polished Chromium Plated
Satin Chromium Plated
US3
US4
US10
US10B
US26
US26D
605
606
612
613
625
626
Plated Finishes (Available on “F—Fire-Rated” models)
Polished Brass on Stainless Steel
Plated Satin Bronze on Stainless Steel
Polished Stainless Steel
Satin Stainless Steel
US3
US10
US32
US32D
632
639
629
630
Optional Finishes:
Consult factory for availability.
Special powder-coated finishes are available.
B1
7200 Series Pivots - Overview
3/4" Offset Pivots - 200 Lb. Doors
7212-7215-7222-7226-7227 Top Pivot
7212 PIVOT SET
7212V Top Pivot
Optional
7222 PIVOT SET
7212V PIVOT SET
7212-7212V-7222
Intermediate Pivot
7212
Bottom Pivot
7222
Bottom Pivot
7212
Bottom Pivot
3/4" Offset Pivots - Standard and Fire-Rated - 500 to 700 Lb. Doors
Optional
7212-7215-7222-7226-7227 Top Pivot
7215F-7226F-7227F Top Pivot
7215 OR 7215F
PIVOT SET
7226 OR 7226F
PIVOT SET
7215 Bottom Pivot
7215F Bottom Pivot
7226-Bottom Pivot
7226F-Bottom Pivot
7227 OR 7227F
PIVOT SET
7215-7226-7227
Intermediate Pivot
7215F-7226F-7227F
Intermediate Pivot
7227-7227F-Bottom Pivot
7215-7226-7227PT
Power Transfer
Intermediate Pivot
3/4" Offset Pivots - Fire-Rated - 1000 to 1750 Lb. Doors
Optional
7230F-7237F Top Pivot
7230F
PIVOT SET
7237F
PIVOT SET
7230F-7237F
Intermediate Pivot
7230F
Bottom Pivot
B2
7237F
Bottom Pivot
7200 Series Pivots - Overview
1-1/2" Offset Pivots - Fire-Rated - 400 to 500 Lb. Doors
Optional
7244F-7245F
Top Pivot
7244F PIVOT SET
7245F PIVOT SET
7244F-7245F
Intermediate Pivot
7244F
Bottom Pivot
7245F
Bottom Pivot
Center Hung Pivots - 300 to 600 Lb. Doors
7253-7255-7255J-7256 Top Pivot
7253
PIVOT SET
7253
Bottom Pivot
7255
PIVOT SET
7255J
PIVOT SET
7255
Bottom Pivot
7255J
Bottom Pivot
7256
PIVOT SET
7256
Bottom Pivot
Center Hung Pivots - 1000 Lb. Doors
7259 Top Pivot
7259 PIVOT SET
7259
Bottom Pivot
B3
7200 Series Pivot Selection Chart
Pivot
Set
UL
Rating
Top
Pivot
Bottom
Pivot
Bottom Pivot
Mounting
Recommended
Intermediate Pivot
3/4"
Offset
7212
None
7212-7215-7222-7226-7227
TOP
7212 BTM
Jamb
Mounted
7212-7212V-7222
INT
7212V
None
7212V
TOP
7212 BTM
Jamb
Mounted
7215
20 min
7212-7215-7222-7226-7227
TOP
7215 BTM
7215F
3 hr
7215F-7226F-7227F
TOP
7222
None
7226
Max Door
Weight
Handed
Yes
200
Yes
7212-7212V-7222
INT
Yes
200
Yes
Jamb
Mounted
7215-7226-7227
INT
Yes
500
Yes
7215F BTM
Jamb
Mounted
7215F-7226F-7227F
INT
Yes
500
Yes
7212-7215-7222-7226-7227
TOP
7222 BTM
Floor
Mounted
7212-7212V-7222
INT
Yes
200
Yes
20 min
7212-7215-7222-7226-7227
TOP
7226 BTM
Floor
Mounted
7215-7226-7227
INT
Yes
600
No
3 hr
7215F-7226F-7227F
TOP
7226F BTM
Floor
Mounted
7215F-7226F-7227F
INT
Yes
600
No
20 min
7212-7215-7222-7226-7227
TOP
7227 BTM
Mortised
Cement Case
7215-7226-7227
INT
Yes
700
No
7227F
3 hr
7215F-7226F-7227F
TOP
7227 BTM
Mortised
Cement Case
7215F-7226F-7227F
INT
Yes
700
No
7230F
3 hr
7230F-7237F
TOP
7230F BTM
Floor
Mounted
7230F-7237F
INT
Yes
1000
No
7237F
3 hr
7230F-7237F
TOP
7237F BTM
Mortised
Cement Case
7230F-7237F
INT
Yes
1750
No
7244F
3 hr
7244F-7245F
TOP
7244F BTM
Floor
Mounted
7244F-7245F
INT
Yes
400
No
7245F
3 hr
7244F-7245F
TOP
7245F BTM
Mortised
Cement Case
7244F-7245F
INT
Yes
500
No
7253
None
7253-7255-7255J-7256
TOP
7253 BTM
Floor
Mounted
None
Yes
300
No
7255
None
7253-7255-7255J-7256
TOP
7255 BTM
Floor
Mounted
None
Yes
500
No
7255J
None
7253-7255-7255J-7256
TOP
7255J BTM
Jamb
Mounted
None
Yes
500
No
7256
None
7253-7255-7255J-7256
TOP
7256 BTM
Mortised
Cement Case
None
Yes
600
No
7259
None
7259
TOP
7259 BTM
Mortised
Cement Case
None
Yes
1000
No
7226F
7227
B4
1-1/2"
Offset
Center
Hung
7212 & 7212V 3/4" Offset
7212V Pivot Set
7212 Pivot Set
7212V Pivot Set
• Handed 3/4" offset pivot set consisting of a jamb
mounted 7212 Bottom Pivot (handed), and a head
frame mounted 7212 Top Pivot (non-handed).
• Door Thickness minimum 1-3/4" (44mm), bevel
1/8" (3mm) in 2" (51mm).
• Center Line Offset 3/4" (19mm) from face of door
and 3/4" from edge of door.
• Maximum Load 200 pounds (91 kg).
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional 7212 Intermediate Pivot (handed) carries
up to an additional 100 pounds (45.5 kg) load
or needed for doors over 7'. See page B14.
• Handed 3/4" offset pivot set consisting of a jamb
mounted 7212 Bottom Pivot (handed), and a jamb
mounted 7212V Top Pivot (handed).
• Door Thickness minimum 1-3/4" (44mm), bevel
1/8" (3mm) in 2" (51mm).
• Center Line Offset 3/4" (19mm) from face of door
and 3/4" from edge of door.
• Maximum Load 200 pounds (91 kg).
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional 7212 intermediate Pivot (handed)
carries up to an additional 100 pounds (45.5 kg)
load or needed for doors over 7'. See page B14.
How to Order:
7212 ___ - ___ - ___ - _____
Mounting Type:
Blank
Head frame mounted to pivot
V
Jamb mounted top pivot
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
B5
7215 & 7215F 3/4" Offset
7215F Pivot Set
7215 or 7215F Pivot Sets
• Handed 3/4" offset pivot set consisting of a jamb
mounted 7215 or 7215F Bottom Pivot (handed)
and a head frame mounted 7215 or 7215F Top Pivot,
(non-handed).
• Door Thickness minimum 1-3/4" (44mm), bevel
1/8" (3mm) in 2" (51mm).
• Center Line Offset 3/4" (19mm) from face of door
and 3/4" from edge of door.
• Maximum Load 500 pounds (227 kg).
• UL Listed
7215 for 20 minute rated door.
7215F for 3 hour rated door.
• 7215F meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional Intermediate Pivot
For 7215 set use 7215 Intermediate Pivot (handed).
For 7215F set use 7215 Intermediate Pivot (handed).
Each Intermediate Pivot carries up to an additional
100 pounds (45.5 kg) load or needed for doors
over 7'. See page B14.
• Optional 7215 PT Power Transfer Intermediate Pivot
(handed). Provides 4 wire transfer with no weight
bearing capabilities. See page B20.
How to Order:
7215 ___ - ___ - ___ - ____
Rating:
Blank
F
Non-fire-rated
Fire-rated
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
PT INT Power transfer intermediate pivot only
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
Non-Fire-Rated
Fire-Rated
B6
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
US3, US10, US32, US32D, SP4, SP10, SP28, SP313, SPBLK
7222 3/4" Offset
7222 Pivot Set
• Handed 3/4" offset pivot set consisting of a base plate
mounted 7222 Bottom Pivot (handed), and a head
frame mounted 7222 Top Pivot (non-handed).
• Door Thickness minimum 1-3/4" (44mm), bevel
1/8" (3mm) in 2" (51mm).
• Center Line Offset 3/4" (19mm) from face of door
and 3/4" from edge of door.
• Maximum Load 200 pounds (91 kg).
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional 7222 Intermediate Pivot (handed) carries
up to an additional 100 pounds (45.5 kg) load
or needed for doors over 7'. See page B14.
How to Order:
7222 - ___ - ___ - _____
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
B7
7226 & 7226F 3/4" Offset
7226 Pivot Set
7226F Pivot Set
• Non-handed 3/4" offset pivot set consisting of a base plate
7226 or 7226F Pivot Sets
•
•
•
•
•
•
•
•
mounted 7226 or 7226F Bottom Pivot, and a head frame
mounted 7226 or 7226F Top Pivot.
Door Thickness minimum 1-3/4" (44mm), bevel
1/8" (3mm) in 2" (51mm).
Center Line Offset 3/4" (19mm) from face of door
and 3/4" from edge of door.
Maximum Load 600 pounds (272 kg).
UL Listed
7226 for 20 minute rated door.
7226F for 3 hour rated door.
7226F meets ANSI/BHMA Grade 1.
Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
Optional Intermediate Pivot
For 7226 set, use 7226 Intermediate Pivot
(handed). For 7226F set, use 7226F Intermediate
Pivot (handed). Each Intermediate Pivot carries up
to an additional 100 pounds (45.5 kg) load or needed
for doors over 7'. See page B14.
Optional 7226 PT Power Transfer Intermediate Pivot
(handed). Provides 4 wire transfer with no weight
bearing capabilities. See page B20.
How to Order:
7226 ___ - ___ - ___ - ___
Rating:
Blank
F
Non-fire-rated
Fire-rated
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
PT INT Power transfer intermediate pivot only
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
Non-Fire-Rated
Fire-Rated
B8
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
US3, US10, US32, US32D, SP4, SP10, SP28, SP313, SPBLK
7227 & 7227F 3/4" Offset
7227 or 7227F Pivot Sets
27F Pivot Set
• Non-handed 3/4" offset pivot set consisting of mortised
cement case mounted 7227 or 7227F Bottom Pivot and
a head frame mounted 7227 or 7227F Top Pivot.
• Door Thickness minimum 1-3/4" (44mm), bevel
1/8" (3mm) in 2" (51mm).
• Center Line Offset 3/4" (19mm) from face of door
and 3/4" from edge of door.
• Maximum Load 700 pounds (318 kg).
• UL Listed
7227 for 20 minute rated door.
7227F for 3 hour rated door.
• 7227F meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional Intermediate Pivot
For 7227 set use 7227 Intermediate Pivot
(handed).For 7227F set use 7227F Intermediate
Pivot (handed).Each Intermediate Pivot carries up
to an additional 100 pounds (45.5 kg) load or needed
for doors over 7'. See page B14.
• Optional 7227 PT Power Transfer Intermediate Pivot
(handed). Provides 4 wire transfer with no weight
bearing capabilities. See page B20.
How to Order:
7227___ - ___ - ___ - ____
Rating:
Blank
F
Non-fire-rated
Fire-rated
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
PT INT Power transfer intermediate pivot only
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
Non-Fire-Rated
Fire-Rated
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
US3, US10, US32, US32D, SP4, SP10, SP28, SP313, SPBLK
B9
7230F 3/4" Offset, Heavy Duty
7230F Heavy Duty Pivot Set
7230F Pivot Set
• Non-handed 3/4" offset pivot set consisting of
a base plate mounted 7230F Bottom Pivot and
a head frame mounted 7230F Top Pivot.
• Door Thickness minimum 1-3/4" (44mm),
bevel 1/8" (3mm) in 2" (51mm).
• Center Line Offset 3/4" (19mm) from
face of door and 3/4" from edge of door.
• Maximum Load 1000 pounds (455 kg).
• Can be used on lead-lined doors.
• UL Listed for 3 hour rated door.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional 7230F Intermediate Pivot (handed)
carries up to an additional 100 pounds (45.5 kg)
load or needed for doors over 7'. See page B15.
How to Order:
7230F - ____ - ____ - ____
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
US3, US10, US32, US32D, SP4, SP10, SP28, SP313, SPBLK
B10
7237F 3/4" Offset, Heavy Duty
7237F Heavy Duty Pivot Set
7237F Pivot Set
• Non-handed 3/4" offset pivot set consisting of a
mortised cement case mounted 7237F Bottom
Pivot and a head frame mounted 7237F Top Pivot.
• Door Thickness minimum 1-3/4" (44mm),
bevel 1/8" (3mm) in 2" (51mm).
• Center Line Offset 3/4" (19mm) from
face of door and 3/4" from edge of door.
• Maximum Load 1750 pounds (795 kg).
• Can be used on lead-lined doors.
• UL Listed for 3 hour rated door.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional 7237F Intermediate Pivot (handed)
carries up to an additional 100 pounds (45.5 kg)
load or needed for doors over 7'. See page B15.
How to Order:
7237F - ___ - ___- ___
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
US3, US10, US32, US32D, SP4, SP10, SP28, SP313, SPBLK
B11
7244F 1-1/2" Offset
7244F Heavy Duty Pivot Set
• Non-handed 1-1/2" offset pivot set consisting of
a base plate mounted 7244F Bottom Pivot and
a head frame mounted 7244F Top Pivot.
• Door Thickness minimum 1-3/4" (44mm),
bevel 1/8" (3mm) in 2" (51mm).
• Center Line Offset 1-1/2" (19mm) from
face of door and 3/4" from edge of door.
• Maximum Load 400 pounds (182 kg).
• UL Listed for 3 hour rated door.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional 7244F Intermediate Pivot (handed)
carries up to an additional 100 pounds (45.5 kg)
load or needed for doors over 7'. See page B15.
How to Order:
7244F - ____ - ____ - ____
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
US3, US10, US32, US32D, SP4, SP10, SP28, SP313, SPBLK
B12
7245F 1-1/2" Offset
7245F Heavy Duty Pivot Set
• Non-handed 1-1/2" offset pivot set consisting
of a mortised cement case mounted 7245F
Bottom Pivot and a head frame mounted 7245F
Top Pivot.
• Door Thickness minimum 1-3/4" (44mm),
bevel 1/8" (3mm) in 2" (51mm).
• Center Line Offset 1-1/2" (19mm) from
face of door and 3/4" from edge of door.
• Maximum Load 500 pounds (227 kg).
• UL Listed for 3 hour rated door.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Optional 7245F Intermediate Pivot (handed)
carries up to an additional 100 pounds (45.5 kg)
load or needed for doors over 7'. See page B15.
How to Order:
7245F - ____ - ____ - ____
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
US3, US10, US32, US32D, SP4, SP10, SP28, SP313, SPBLK
B13
7200 Series Intermediate Pivots
General Information:
• Door Height NFPA 80, Section 3-8.3, requires
additional intermediate pivot for some fire-rated
doors. We recommend one for every 2'6" (762mm),
or fraction thereof, door height over 5'0" (1524mm).
• Door Weight exceeding pivot set limit, add
one intermediate pivot for each 100 lbs.
(45.5 kg) additional.
• Door Thickness minimum 1-3/4" (44mm),
bevel 1/8" (3mm) in 2" (51mm).
7212-7212V-7222 INT
• Handed 3/4" offset pivots compatible with the
following pivot sets: 7212, 7212V and 7222.
• Maximum Load 100 pounds (45.5 kg).
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Finishes: US3, US4, US10, US10B, US26, US26D,
SP4, SP10, SP28, SP313 and SPBLK.
7215-7226-7227 INT
• Handed 3/4" offset pivots compatible
with the following pivot sets: 7215,
7226 and 7227.
• Maximum Load 100 pounds (45.5 kg).
• UL Listed for 20 minute rated door.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Finishes: US3, US4, US10, US10B, US26, US26D,
SP4, SP10, SP28, SP313 and SPBLK.
7215F-7226F-7227F INT
• Handed 3/4" offset pivots compatible
with the following pivot sets: 7215F,
7226F and 7227F.
• Maximum Load 100 pounds (45.5 kg).
• UL Listed for 3 hour rated door.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Finishes: US3, US10, US32, US32D, SP4, SP10,
SP28, SP313 and SPBLK.
B14
15-7226-7227 INT
15F-7226F-7227F INT
7200 Series Intermediate Pivots
0F 7237F INT
7230F - 7237F INT
• Handed 3/4" offset pivots compatible
with the following pivot sets: 7230F
and 7237F.
• Maximum Load 100 pounds (45.5 kg).
• Can be used on lead-lined doors.
• UL Listed for 3 hour rated door.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Finishes: US3, US10, US32, US32D,
SP4, SP10, SP28, SP313 and SPBLK.
7244F - 7245F INT
Intermediate Pivot
7244F-7245F INT
• Handed 1-1/2" offset pivots compatible
with the following pivot sets: 7244F
and 7245F.
• Maximum Load 100 pounds (45.5 kg).
• UL Listed for 3 hour rated door.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment Range of 3/16" (5mm),
which includes a positive locking feature.
• Finishes: US3, US10, US32, US32D,
SP4, SP10, SP28, SP313 and SPBLK.
B15
7253 Center Hung Pivot Set
7253 Pivot Set
7253 Pivot Set
• Center hung pivot set consisting of base plate
mounted 7253 Bottom Pivot and a head frame
mounted 7253 Top Pivot.
• Maximum Load 300 pounds (136 kg).
• Easy Installation Tilt on bearing and bearing pin.
• Door Thickness minimum 1-3/4" (44mm).
• Radius Stop (A) to clear heel edge of door.
• Pivot Distance (B) 1-3/4" (44mm) minimum from
jamb to centerline of pivot pin. Radius heel edge
of door, 1-5/8" (41mm) minimum recommended.
• Clearance from bottom edge of door to the floor
mounting surface is adjustable from 3/16" (5mm)
to 3/4" (19mm) by varying the depth of the mortise
(C) in the bottom rail of the door, refer to Table D.
Over 3/4" (19mm) from the door to floor mounting
surface, consult factory.
• Vertical Adjustment based on mortise preparation
in bottom rail of the door. Refer to Table D.
Table D
Clearance
Depth of Mortise
3/16" (5mm)
3/8" (10mm)
1/2" (13mm)
5/8" (16mm)
3/4" (19mm)
1-3/16" (30mm)
1" (25mm)
7/8" (22mm)
3/4" (19mm)
5/8" (16mm)
How to Order:
7253 - ___ - ____
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
Finishes:
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
B16
7255 & 7255J Center Hung Pivot Sets
7255 Pivot Set
7255J Pivot Set
• Center hung pivot set consisting of base plate mounted 7255
Bottom Pivot and a head frame mounted 7255 Top Pivot.
• Maximum Load 500 pounds (227 kg).
• Door Thickness minimum 1-3/4" (44mm).
• Radius Stop (A) to clear heel edge of door.
• Pivot Distance (B) 1-3/4" (44mm) minimum from jamb to
centerline of pivot pin. Radius heel edge of door, 1-5/8"
(41mm) minimum recommended.
• Clearance from bottom edge of door to the floor mounting
surface is adjustable from 3/16" (5mm) to 3/4" (19mm) by
varying the depth of the mortise (C) in the bottom rail of the
door, refer to Table D. Over 3/4" (19mm) from the door to
floor mounting surface, consult factory.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment based on mortise preparation
in bottom rail of the door. Refer to Table D, pg. B16.
• Center hung pivot set consisting of jamb mounted 7255J
Bottom Pivot and a head frame mounted 7255 Top Pivot.
• Maximum Load 500 pounds (227 kg).
• Door Thickness minimum 1-3/4" (44mm).
• Radius Stop (A) to clear heel edge of door.
• Pivot Distance (B) 1-3/4" (44mm) minimum from jamb to
centerline of pivot pin. Radius heel edge of door, 1-5/8"
(41mm) minimum recommended.
• Clearance from bottom edge of door to the floor mounting
surface is adjustable from 3/16" (5mm) to 3/4" (19mm) by
varying the depth of the mortise (C) in the bottom rail of the
door, refer to Table D. Over 3/4" (19mm) from the door to
floor mounting surface, consult factory.
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment based on mortise preparation
in bottom rail of the door. Refer to Table D, pg. B16.
How to Order:
7255 ___ - ___ - ___
Mounting:
Blank
Floor mounted bottom pivot
J
Jamb mounted bottom pivot
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
Finishes:
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
B17
7256 Center Hung Pivot Set
7256 Pivot Set
7256 Pivot Set
• Center hung pivot set consisting of mortised cement
case mounted 7256 Bottom Pivot and a head frame
mounted 7256 Top Pivot.
• Door Thickness minimum 1-3/4" (44mm).
• Radius Stop (A) to clear heel edge of door.
• Pivot Distance (B) 1-3/4" (44mm) minimum
from jamb to centerline of pivot pin. Radius
heel edge of door, 1-5/8" (41mm) minimum
recommended.
• Clearance from bottom edge of door to the floor
mounting surface is adjustable from 3/16" (5mm)
to 3/4" (19mm) by varying the depth of the mortise
(C) in the bottom rail of the door, refer to Table D.
Over 3/4" (19mm) from the door to floor mounting
surface, consult factory.
• Maximum Load 600 pounds (272 kg).
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment based on mortise preparation
in bottom rail of the door. Refer to Table D.
Table D
Clearance
Depth of Mortise
3/16" (5mm)
3/8" (10mm)
1/2" (13mm)
5/8" (16mm)
3/4" (19mm)
1-3/16" (30mm)
1" (25mm)
7/8" (22mm)
3/4" (19mm)
5/8" (16mm)
How to Order:
7256 - ___ - _____
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
Finishes:
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
B18
7259 Center Hung Pivot Set
7259 Pivot Set
7259 Pivot Set
• Center hung consisting of mortised cement case
mounted 7259 Bottom Pivot and a head frame
mounted 7259 Top Pivot.
• Door Thickness minimum 2" (51mm).
• Radius Stop (A) to clear heel edge of door.
• Pivot Distance (B) 1-3/4" (44mm) minimum
from jamb to centerline of pivot pin. Radius
heel edge of door, 1-5/8" (41mm) minimum
recommended.
• Clearance from bottom edge of door to the floor
mounting surface is adjustable from 3/16" (5mm)
to 3/4" (19mm) by varying the depth of the mortise
(C) in the bottom rail of the door, refer to Table D.
Over 3/4" (19mm) from the door to floor mounting
surface, consult factory.
• Maximum Load 1000 pounds (455 kg).
• Meets ANSI/BHMA Grade 1.
• Vertical Adjustment based on mortise preparation
in bottom rail of the door. Refer to Table D.
Table D
Clearance
Depth of Mortise
3/16" (5mm)
3/8" (10mm)
1/2" (13mm)
5/8" (16mm)
3/4" (19mm)
1-3/16" (30mm)
1" (25mm)
7/8" (22mm)
3/4" (19mm)
5/8" (16mm)
How to Order:
7259 - ___ - _____
Pivot Style:
Blank
Top and bottom set
TOP
Top pivot only
BTM
Bottom pivot only
Finishes:
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
B19
7200 Series Power Transfer Pivots
7215PT - 7226PT - 7227PT Pivot
Power Transfer Intermediate Pivot
7215-7226-7227 PT
• Handed 3/4" intermediate offset pivot compatible
with 7210, 7220 or 7230 Series pivot sets.
• Center Line Offset 3/4" (19mm) from face of door
and 3/4" from edge of door.
• Power Transfer Pivot features two pairs of
conductors providing two separate, low voltage
electric power and/or signal circuits between the
door leaf and frame.
• Electrical Max. 1.0 Ampere @24V DC per pair
of 28 gauge conductors.
• Non-Load Bearing Pivots.
• Door Thickness minimum 1-3/4" (44mm), bevel
1/8" (3mm) in 2" (51 mm).
• Raceway preparation required between the door leaf
area and door mounted electrical device. A raceway
or other preparation is required to protect wiring
routed through all grout filled frames.
Options:
• 8 Wires
How to Order:
72 ____ PT - ____ - _____
Model:
15
26
27
Handing:
LH
RH
Left-hand door
Right-hand door
Finishes:
US3, US4, US10, US10B, US26, US26D, SP4, SP10, SP28, SP313, SPBLK
B20
91105F Pocket Pivot
91105F Pocket Pivot Hinge
• Full mortised and non-handed pocket pivot with heavy duty
ball bearings.
• UL Listing for 3 hour rated metal doors or 20 minute wood
fire doors.
• Stainless steel base material.
• For use on pocket door corridor application common in
hospitals, hotels and high rise buildings. The Pocket Pivot
allows the door when in the open position to be flush in the
pocket of the corridor, thus keeping the door out of the way
of traffic.
• Allows door to open 90°.
• Each pivot carries 90 pounds of door weight.
• Recommended quantities per door up to 7' are two pivots.
Over 7' openings use three pivots.
• Optional Power Transfer Pivot, features two pairs of conductors
providing two separate, low voltage electric power and/or
signal circuits. May be used with Von Duprin “EL” exit devices.
How to Order:
91105F - _____ - ______
Finishes:
US3, US10, US32, US32D, SP313, USP
Pivot Type:
Blank
Standard
PT
Power transfer
B21
91105F Pocket Pivot
Pocket Pivot
Cutout
Door Portion
Jamb Portion
1-3/8
1-1/8
1-9/64
1-9/64
5-17/32
1-1/8
CL
of Door
B22
Notes
B23
Notes
B24
Section C
Architectural Door Trim
Architectural Door Trim
8100 Series Door Pulls
• Made from the finest architectural brass, stainless steel
and aluminum available.
• Each pull is carefully machined, polished and inspected before
being individually wrapped and packaged.
• Door pulls are packed with standard type fasteners for 1-3/4"
doors. For special mounting methods other than standard,
see pages C11 - C13.
• For sizes and finishes not listed in this catalog, contact our
Customer Service Department for availability.
How to Order
8102 - ___ - ___ - ___
Size:
6
8
0
for 6"
for 8"
for 10"
Finishes:
US3, US4, US5, US10, US10B, US15, US15A, US26,
US26D, US28, US32, US32D
8102 Door Pull
Prod.
No.
Proj.
“A”
Center to Center
“B”
Overall Length
“C”
8102-6
8102-8
8102-0
2-1/4"
2-1/4"
2-1/4"
6"
8"
10"
6-3/4"
8-3/4"
10-3/4"
Mounting
Blank
F
H
I
J
Type:
standard
Concealed wood door w/push plate (special)
Concealed metal door (special)
Concealed wood door
Back to back pulls, furnished is pairs (PR)
unless single pull (SGL) specified
How to Order
8103 - ___ - ___ - ___
Size:
8
0
2
for 8"
for 10"
for 12"
Finishes:
US3, US4, US5, US10, US10B, US15, US15A, US26,
US26D, US28, US32, US32D
8103 Door Pull
Prod.
No.
Proj.
“A”
Center to Center
“B”
Overall Length
“C”
8103-8
8103-0
8103-2
2-1/2"
2-1/2"
2-1/2"
8"
10"
12"
9"
11"
13"
Mounting
Blank
F
H
I
J
Type:
standard
Concealed wood door w/push plate (special)
Concealed metal door (special)
Concealed wood door
Back to back pulls, furnished in pairs (PR)
unless single pull (SGL) specified
C1
Architectural Door Trim
8100 Series Door Pulls
• Made from the finest architectural brass, stainless steel
and aluminum available.
• Each pull is carefully machined, polished and inspected before
being individually wrapped and packaged.
• Door pulls are packed with standard type fasteners for 1-3/4"
doors. For special mounting methods other than standard,
see pages C11 - C13.
• For sizes and finishes not listed in this catalog, contact our
Customer Service Department for availability.
How to Order
8103EZ - ___ - ___ - ___
Size:
8 for 8"
0 for 10"
2 for 12"
Finishes
US3, US4, US10, US10B, US15, US15A
US26, US26D, US28, US32, US32D
8103EZ Door Pull - Large 2-1/2" Clearance for the Physically Impaired
Prod.
No.
8103EZ
8103EZ
8103EZ
Proj.
“A”
Center to Center
“B”
3-1/2"
3-1/2"
3-1/2"
8"
10"
12"
Overall Length
“C”
9"
11"
13"
Mounting Type:
Blank Standard
L
Surface Concealed Two-Anchor
M
Back-To-Back with Spanner Collar. Furnished in Pairs. (PR)
M1
Single (SGL) Pull. Back-to-back With
Spanner Collar. RH Thread.
M2
Single (SGL) Pull. Back-to-back With
Spanner Collar. LH Thread.
N
Back-to-Back Two-Anchor. Furnished in Pairs. (PR)
N2
Single (SGL) Pull, Back-to-Back Two Anchor.
O
Decorative Blind Thru-Bolt
How to Order
8105 - ___ - ___ - ___
Size:
6
8
0
for 6"
for 8"
for 10"
8105 Door Pull
Prod.
No.
Proj.
“A”
Center to Center
“B”
Overall Length
“C”
8105-6
8105-8
8105-0
2"
2"
2"
6"
8"
10"
6-1/2"
8-1/2"
10-1/2"
C2
Finishes:
US3, US4, US5, US10, US10B, US15, US15A, US26,
US26D, US28, US32, US32D
Mounting Type:
Blank
Standard
F
Concealed wood door w/push plate (special)
Architectural Door Trim
8100 Series Door Pulls
• Made from the finest architectural brass, stainless steel
and aluminum available.
• Each pull is carefully machined, polished and inspected before
being individually wrapped and packaged.
• Door pulls are packed with standard type fasteners for 1-3/4"
doors. For special mounting methods other than standard,
see pages C11 - C13.
• For sizes and finishes not listed in this catalog, contact our
Customer Service Department for availability.
How to Order
8111-5 - ____ - ____
Finishes:
US3, US4, US5, US10, US10B, US15, US15A,
US26, US26D, US28, US32, US32D
8111-5 Door Pull
Prod.
No.
Proj.
“A”
Center to Center
“B”
Overall Length
“C”
8111-5
1-13/16"
5-1/4"
6-1/4"
Mounting
Blank
F
G
Type:
Standard
Concealed wood door w/push plate (special)
Concealed w/pull plate
How to Order
8112-5 - ____
8112 Door Pull
Prod.
No.
Proj.
“A”
Center to Center
“B”
Overall Length
“C”
8112-5
2-3/16"
5-5/8"
7-1/2"
Finishes:
US3, US4, US10, US10B, US15, US15A, US26,
US26D, US28
C3
Architectural Door Trim
8100 Series Door Pulls
• Made from the finest architectural brass, stainless steel
and aluminum available.
• Each pull is carefully machined, polished and inspected before
being individually wrapped and packaged.
• Door pulls are packed with standard type fasteners for 1-3/4"
doors. For special mounting methods other than standard,
see pages C11 - C13.
• For sizes and finishes not listed in this catalog, contact our
Customer Service Department for availability.
D
E
U
N
I
T
N
O
C
DIS
How to Order
8113-5 - ____ - ____
Finishes:
US3, US4, US10, US10B, US15, US15A, US26,
US26D, US28
8113 Door Pull
Prod.
No.
Proj.
“A”
Center to Center
“B”
Overall Length
“C”
8113-5
2-3/16"
5-5/8"
7-1/2"
Mounting Type:
Blank
Standard
F
Concealed wood door w/push plate (special)
D
E
U
N
I
T
N
O
C
DIS
13/16"
How to Order
8114-5 -_____ - ____
Finishes:
US3, US4, US10, US10B, US15, US15A, US26,
US26D, US28, US32D
8114 Door Pull
Prod.
No.
Proj.
“A”
Center to Center
“B”
Overall Length
“C”
8114-5
1-11/16"
5-1/4"
6-3/16"
C4
Mounting
Blank
F
G
Type:
Standard
Concealed wood door w/push plate (special)
Concealed w/pull plate
Architectural Door Trim
8100 Series Door Pulls
• Made from the finest architectural brass, stainless steel
and aluminum available.
• Each pull is carefully machined, polished and inspected before
being individually wrapped and packaged.
• Door pulls are packed with standard type fasteners for 1-3/4"
doors. For special mounting methods other than standard,
see pages C11 - C13.
• For sizes and finishes not listed in this catalog, contact our
Customer Service Department for availability.
How to Order
8121-5 - ____ - ____
Finishes:
US3, US10, US10B, US15, US15A, US26,
US26D, US28
8121 Door Pull
Prod.
No.
Proj.
“A”
Center to Center
“B”
Overall Length
“C”
8121-5
3-1/2"
5-3/4"
8-3/4"
Mounting
Blank
F
K
Type:
Standard
Concealed wood door w/push plate (special)
Back to back pulls. Furnished is Pairs (PR).
How to Order
Size:
8 for 8"
0 for 10"
2 for 12"
18 for 18"
8190 - ___ - ___ - ___
Finishes
US3, US4, US10, US10B, US15, US15A,
US26, US26D, US32, US32D
8190 90° Offset Door Pull
Prod.
No.
8190
8190
8190
8190
Proj.
“A”
3-1/4"
3-1/4"
3-1/4"
3-1/4"
Center to Center
“B”
8"
10"
12"
18"
Overall Length
“C”
9"
11"
13"
19"
Mounting Type:
Blank Standard
L
Surface Concealed Two-Anchor
M
Back-To-Back with Spanner Collar. Furnished in Pairs. (PR)
M1 Single (SGL) Pull. Back-to-Back With
Spanner Collar. RH Thread.
M2 Single (SGL) Pull. Back-to-Back With
Spanner Collar. LH Thread.
N
Back-to-Back Two-Anchor. Furnished in Pairs. (PR)
N2
Single (SGL) Pull, Back-to-Back Two Anchor.
O
Decorative Blind Thru-Bolt
C5
Architectural Door Trim
9100 Series Push Bars and Pulls
• Pushbars and pulls are packed with standard type fasteners for
1-3/4" doors. For special mounting methods, see pages C11 - C13.
• For sizes and finishes not listed in this catalog, contact Customer
Service for availability.
• Made from the finest architectural brass and stainless steel.
• Each pushbar and pull is carefully machined, polished and
inspected before being individually wrapped and packaged.
How to Order
9100 - ___ - ___ - ___
Size Push:
28, 33
Finishes
US3, US4,
US32, US32D
9100 Pushbar
Prod No.
Proj.
Center to Center
Overall Length
9100
9100
2-1/2"
2-1/2"
28"
33"
29"
34"
* For other length pushbars, contact customer service for avaliability
* Caution - Please be sure that the length pushbar you order does not interfere with the door
jamb or cause a pinch point
Mounting Type:
NS
NO
Standard (Type N and Standard)
Decorative (Type N and Type O)
To Determine Pushbar Center-To-Center
Flush Door - Door width minus 5"
Stile & Rail Door - Door width minus width of one stile
How to Order
9103 - ___ - ___ - ___ - ___
Size Push:
28, 33
Size Pull
8 for 8", 0 for 10", 2 for 12"
Finishes
US3, US4,
US32, US32D
9103 Straight Pull/Pushbar Combo (8103 pull + 9100 push)
Prod No.
9103
9103
9103
CTC Push
CTC Pull
Proj Push&Pull
28", 33"
28", 33"
28", 33"
8"
10"
12"
2-1/2" & 2-1/2"
2-1/2" & 2-1/2"
2-1/2" & 2-1/2"
* For other length pushbars, contact customer service for avaliability
* Caution - Please be sure that the length pushbar you order does not interfere with the door
jamb or cause a pinch point
C6
Mounting Type:
NS
NO
Standard (Type N and Standard)
Decorative (Type N and Type O)
To Determine Pushbar Center-To-Center
Flush Door - Door width minus 5"
Stile & Rail Door - Door width minus width of one stile
Architectural Door Trim
9100 Series Push Bars and Pulls
• Made from the finest architectural brass and stainless steel.
• Each pushbar and pull is carefully machined, polished and
inspected before being individually wrapped and packaged.
• Pushbars and pulls are packed with standard type fasteners for
1-3/4" doors. For special mounting methods, see pages C11 - C13.
• For sizes and finishes not listed in this catalog, contact Customer
Service for availability.
How to Order
9103EZ - ___ - ___ - ___ - ___
Size Push:
28, 33
Size Pull
8 for 8", 0 for 10", 2 for 12"
Finishes
US3, US4,
US32, US32D
9103EZ Straight Pull/Pushbar Combo (8103EZ Pull + 9100 Push)
Prod No.
9103EZ
9103EZ
9103EZ
CTC Push
CTC Pull
Proj Push&Pull
28", 33"
28", 33"
28", 33"
8"
10"
12"
2-1/2" & 3-1/2"
2-1/2" & 3-1/2"
2-1/2" & 3-1/2"
* For other length pushbars, contact customer service for avaliability
Mounting Type:
NS
NO
Standard (Type N and Standard)
Decorative (Type N and Type O)
To Determine Pushbar Center-To-Center
Flush Door - Door width minus 5"
Stile & Rail Door - Door width minus width of one stile
* Caution - Please be sure that the length pushbar you order does not interfere with the door jamb or
cause a pinch point
How to Order
9190 - ___ - ___ - ___ - ___
Size Push:
28, 33
Size Pull
8 for 8", 0 for 10", 2 for 12", 18 for 18"
Finishes
US3, US4,
US32, US32D
9190 Offset Pull/Pushbar Combo (8190 pull + 9100 push)
Prod No.
9190
9190
9190
9190
CTC Push
CTC Pull
Proj Push&Pull
28", 33"
28", 33"
28", 33"
28", 33"
8"
10"
12"
18"
2-1/2" & 3-1/4"
2-1/2" & 3-1/4"
2-1/2" & 3-1/4"
2-1/2" & 3-1/4"
Mounting Type:
NS
NO
Standard (Type N and Standard)
Decorative (Type N and Type O)
To Determine Pushbar Center-To-Center
Flush Door - Door width minus 5"
Stile & Rail Door - Door width minus width of one stile
* For other length pushbars, contact customer service for avaliability
* Caution - Please be sure that the length pushbar you order does not interfere with the door
jamb or cause a pinch point
C7
Architectural Door Trim
8200 Series Push Plates and
8300 Series Pull Plates
• Made from the finest architectural aluminum, brass,
and stainless steel.
• For Push Plate sizes other than listed, contact our Customer
Service Department or your local sales representative.
• All aluminum, brass, and stainless steel Push Plates meet
ANSI A156.6 requirements for .050" thickness.
• Each Push Plate is packaged individually wrapped with
mounting screws.
• For special mounting methods other than standard,
see pages C11 - C13.
Push and Pull Plates Cut for Cylinder or Thumbturns
• All plates may be ordered with cutout for cylinder or thumbturn.
Standard cutouts are positioned 2" from top of plate and
centered on plates up to 4" wide or 2" from edge on plates
over 4" wide. Specify hand of door when ordering cutout for
plates wider than 4". On pull plates, if the pulls center-to-center
dimension interferes with the cutout for the cylinder or
thumbturn, please provide drawing of cutout location when
ordering.
• Standard size for cylinder cutouts is 1-1/4" diameter and for
thumbturn cutout is 3/8" diameter.
• When ordering, add suffix CFC for cut for cylinder, and CFT
for cut for thumbturn to product number.
How to Order
8 ___ - ____ -____ - ____ - ____
Model:
200
300
Push Plate,
Pull Plate, less pull
Hole Spacing: (for Pull Plate only)
5
for 5-1/4"
6
for 6"
8
for 8"
0
for 10"
Finishes:
US3, US4, US5, US10, US10B, US15, US15A,
US26, US26D, US28, US32, US32D
8200 Push Plate
8300 Pull Plate (less pull)
Available Sizes
3" x 12"
3.5" x 15"
4" x 16"
6" x 16"
8" x 16"
C8
Size:
3 x 12, 3-1/2 x 15, 4 x 16, 6 x 16, 8 x 16
Special Options: (specify handing for plates over 4" wide)
CFC
Cylinder cutout
CTC
Thumbturn cutout
Architectural Door Trim
8300 Series Pull Plates
• Made from the finest architectural aluminum, brass
and stainless steel.
• For Pull Plate sizes other than listed, contact our Customer Service
Department or your local sales representative.
• All aluminum, brass, and stainless steel Pull Plates meet ANSI
A156.6 requirements for .050" thickness.
8302 Pull Plate
• 8300 Plate
3-1/2" x 15"
4" x 16"
6" x 16"
• 8102 Pull
6" centers
8" centers
10" centers
• Each Pull Plate is packaged individually wrapped with
mounting screws.
• Pulls are centered on plates up to 4" wide and offset 2" from edge
of plates wider than 4".
• For special mounting methods other than standard, see pages
C11 - C13.
8303 and 8303EZ Pull Plate
8305 Pull Plate
• 8300 Plate
3-1/2" x 15"
4" x 16"
6" x 16"
• 8300 Plate
3-1/2" x 15"
4" x 16"
6" x 16"
How to Order
• 8103 Pull
8" centers
10" centers
• 8105 Pull
6" centers
8" centers
10" centers
83 ____ - ____ - _____ - _____ - ____ - ____
Pull Style:
02
for 8102
03
for 8103
05
for 8105
Pull Center to Center:
6
for 6" (not available on 8303)
8
for 8"
0
for 10"
Finishes:
US3, US4, US5, US10, US10B, US15, US15A, US26, US26D, US28, US32D
Size:
3-1/2" x 15", 4" x 16", 6" x 16"
Special Options: (Handing needed for 6" x 16", LH or RH)
CFC
Cylinder cutout
CTC
Thumbturn cutout
Mounting:
Blank
F
G
I
J
Standard
Concealed pull wood doors w/push plate (special. Not available 8303EZ.)
Concealed pull plate (Only available 8302, 8303 and 8303EZ)
Concealed pull wood door (not available 8305 and 8303EZ)
Back to back pull (not available 8305 and 8303EZ)
C9
Architectural Door Trim
8300 Series Pull Plates
• Made from the finest architectural aluminum, brass
and stainless steel.
• For Pull Plate sizes other than listed, contact our Customer Service
Department or your local sales representative.
• All aluminum, brass and stainless steel Pull Plates
meet ANSI A156.6 requirements for .050" thickness.
• Each Pull Plate is packaged individually wrapped with
mounting screws.
• Pulls are centered on plates up to 4" wide and offset 2" from
edge of plates wider than 4".
• For special mounting methods other than standard, see pages
C11 - C13.
ED
U
N
NTI
O
C
8314 Pull Plate
DIS
13/16"
8311 Pull Plate
• 8300 Plate
3-1/2" x 15"
4" x 16"
6" x 16"
• 8111-5 Pull
5-1/4" centers
How to Order
• 8300 Plate
3-1/2" x 15"
4" x 16"
6" x 16"
83 ____ - 5 - ____ - ____ - ____- ____
Pull Style:
11
for 8111
14
for 8114
Finishes:
US3, US4, US5, US10, US10B, US15, US15A, US26, US26D,
US28, US32D
Size:
3-1/2" x 15", 4" x 16", 6" x 16"
Special Options: (Handing needed for 6" x 16", LH or RH)
CFC
Cylinder cutout
CTC
Thumbturn cutout
Mounting:
Blank
Standard
F
Concealed pull wood doors w/push plate (special)
G
Concealed pull plate
C10
• 8114-5 Pull
5-1/4" centers
Architectural Door Trim
Mounting
• All mounting hardware is for standard 1-3/4" door.
• Consult Customer Service if other than standard.
Standard Mounting
Type G
Concealed Pull Plate Mounting
• (2) 1/4-20 x 2-1/4" brass, oval head machine screws;
plated to match.
• (2) No. 14 countersunk washers; plated to match
Available only for 8302, 8303, 8311 and 8314 Pull Plates.
Type F-Special
Wood Doors
Concealed Pull Mounting With Push Plate
Type H-Special
Reinforced Hollow Metal Door
Concealed Pull Mounting
• (2) 1/4-20 x 2-1/4" steel flat head machine screws; zinc plated.
Available only for 8102 and 8103 Pulls.
Available only for 8102, 8103, 8105, 8111, 8113, 8114, 8302,
8303, 8305, 8311, 8313 and 8314. Plate on opposite side of
door must be ordered separately.
• (2) 1/4-20 x 5/8" steel flat head machine screws; zinc plated.
Pull mounts directly onto plate. Plate is attached to door
by 6 screws.
• (2) Steel screw sleeves; zinc plated.
• (2) 1/4-20 x 1-1/4" steel countersunk trim head machine screw;
zinc plated.
C11
Architectural Door Trim
Mounting
• All mounting hardware is for standard 1-3/4" door.
• Consult Customer Service if other than standard.
Type I
Wood Doors
Concealed Pull Mounting
Type J
Back to Back Pull Mounting
Available only for 8102 and 8103 Pulls.
Available only for 8102, 8103, 8302 and 8303 Pulls.
• (2) 10 x 1-1/2" No. 10 steel countersunk trim head sheet
metal screws; zinc plated.
• (2) Steel screw sleeves; zinc plated.
• (2) 1/4-20 x 2-3/4" No. 10 steel countersunk trim head
machine screws; zinc plated.
Pulls furnished in pairs (PR) unless single (SGL) specified.
Type K
Back to Back Pull Mounting
Type L
Reinforced Hollow Metal Door
Available only for 8121-5 Pulls.
Available only for 8103EZ and 8190 Pulls.
• (4) Steel screw sleeve nuts; steel zinc plated.
• (8) No. 8-32 x 1" brass oval head machine screws; plated to
match.
Pulls furnished in pairs (PR).
• (2) 1/4-20 x 1-1/4" steel countersunk trim head machine screws
with (4) set screws for maximum anchoring force
• (2) Steel screw sleeves; zinc plated.
C12
Architectural Door Trim
Mounting
• All mounting hardware is for standard 1-3/4" door.
• Consult Customer Service if other than standard.
Fastener Guide
• Through bolt fasteners are for standard 1-3/4" thick doors.
• For fasteners other than shown contact our Customer Service
Department for availability.
Type NS-Standard Push/Pull Mounting
Type N & Standard
Pushbar to Pull
- (1) 1/4-20 X 3"steel countersunk trim head machine screws with (2) set screws.
- (1) steel screw sleeve, zinc plated.
Free End Pushbar & Pull
- (2) 1/4-20 X 2-1/4" brass, oval head mach screws; plated to match.
- (2) No. 14 countersunk washers; plated to match.
Type NO Push/Pull Mounting
Type N & Type O
Pushbar to Pull
- (1) 1/4-20 X 3"steel countersunk trim head machine screws with (2) set screws.
- (1) steel screw sleeve, zinc plated.
Free End Pushbar & Pull
- (2) 1/4-20 X 2-1/4" blind thru-bolts; plated to match.
C13
Architectural Door Trim
Series 8400 Door Protection Plates
.050" Thickness
Features:
• Door Protection Plates are fabricated from the finest architectural
aluminum, brass, and stainless steel, or 1/8" thick clear acrylic
plastic or black or brown high impact polyethylene.
• All aluminum, brass, bronze and stainless steel Door Protection
Plates meet ANSI A156.6 requirements for .050" thickness.
• Optional Beveling—For beveling of top and two sides of plates
suffix with B3E, and for beveling of four sides suffix with B4E.
Plastic plates are beveled on all four sides as standard.
• Each plate is packaged carefully wrapped in strong kraft paper with
#6 x 5/8" oval head, undercut sheet metal screws plated to match,
for easy installation on hollow metal, laminate, or wood doors. All
plates are packaged in heavy duty corrugated cardboard; larger
plates are enclosed in a wooden frame.
• Use No. 8401 Kickplate Gasket Tape as a buffer between brass
kickplates and metal doors to help prevent tarnishing which may
result from electrolytic oxidation. One package provides enough
double-sided adhesive-backed foam tape for the perimeter of an
8" x 34" plate.
• Finishes:
Brass: B3, B4, B5, B10, B10B (for heights over 24", check with
customer serivce)
Stainless Steel: S32D, S32
Aluminum: PA28
Plastic: BLK, BRN, CLR
Mop Plates
Kick Plates
Stretcher Plates
Armor Plates
• Protect the bottom of the
pull side of door subject
to cleaning and mopping
procedures.
• Size Ranges:
4" to 6" high, 22" to 48" wide
• Protect the bottom of the
push side of doors subject
to scuffing from foot traffic.
• Recommended for all
doors subject to normal
use (especially doors using
a closer).
• Size Ranges:
8" to 24" high, 22" to 48" wide
• Protect doors at specific
areas where consistent
contact is made by
stretchers, service carts
or other equipment.
• Usually applied to push
side of doors.
• Specify “B4E” Option for
beveled edges.
• Size Ranges:
6" to 8" high, 22" to 48" wide
• Protect lower half of doors
from abuse by hard carts,
trucks and rough usage.
• Usually applied to push side
of single doors and both
sides of double acting doors.
• Size Ranges:
26" to 48" high, 22" to
48" wide
How to Order
8400 ____ - _____ x _____ - _____
Finish
Height:
4" up to 48" in 1/2" increments
(For brass kick plates over 24", check with customer service.)
Width:
22" up to 48" in 1/2" increments
Options: (Only for metal plates)
B3E for Bevel Top and 2 Edges
B4E for Bevel 4 Edges
CS for Counter Sink Holes
ES for Extra row of Screws
C14
Architectural Door Trim
Series 8400 Residential Grade (RG) and Light Grade (LG) Door Protection Plates
.037" Thickness
• Each non-magnetic plate is packed with #6 x 5/8" oval head,
undercut sheet metal screws plated to match, for installation on
hollow metal, laminate or wood doors.
Features:
• All RG and LG plates are .037" thick.
• Each plate is packaged in strong kraft paper or is carded.
• Selected sizes and finishes available in magnetic form for easy
installation on hollow metal doors.
Standard Plates (for additional sizes, check with Customer Service)
Model
Finish
6 x 34
8 x 30
8 x 34
8400 RG
B-505
Ultima Lifetime Finish
✓
✓
✓
✓
B3/B-605
✓
✓
✓
✓
B5
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
B-613
B-619
B-620
B-625
PA3
PA28
8400 LG
S32D
8400 MAG
B-505
Size: 6 x 30
D
E
U
N
I
T
N
O
C
DIS
B3/B-605
PA3
✓
✓
✓
✓
✓
✓
✓
✓
C15
Vandal Resistant Trim
VR900 Series
Features:
• Stainless Steel construction, 11 gage (0.120" thick).
• Thru-bolts and rugged mounting screws for maximum
fastening strength.
• 1/4-20 screws and stainless steel finishing washers supplied
with VR900 models; 10-24 screws supplied with VR910 models.
• Built-in lock protector prevents vandalism to mortise latchbolt
(available on certain models).
• Extra-tough stainless steel cylinder collar prevents pipe wrench or
similar tool from damaging cylinder. Tapered design prevents side
impacts from transferring directly to cylinder. Collar spins freely.
• Sleek, attractive design.
• Furnished with mounting screws for door thicknesses of 1-3/4"
to 2-1/4".
• Finish: US32D.
• Grip coated in black plastisol for softer touch and resilience to
temperature extremes. Grip designed for comfortable operation.
• Meets ANSI/BHMA 156.13, Trim Security Test and California State
Accessibility Standards Title 24.
VR900-RHR
VR900-LHR
VR900LLP-RH
VR900LLP-LH
• For use with most mortise locks on outswinging doors,
including Schlage L9000 Series locks with interior
L escutcheon, N escutcheon, and rose trims.
• Includes built-in lock protector and cylinder cutout.
• Handed design allows trim to be positioned to coordinate
with the centerline of inside hardware.
• For use with most mortise locks on inswinging doors,
including Schlage L9000 Series locks with interior
L escutcheon, N escutcheon, and rose trims.
• Includes cutout for cylinder, less lock protector (LLP).
• Handed design allows trim to be positioned to coordinate
with the centerline of inside hardware.
Prod.
No.
Width
Height
Thru-Bolt
Pattern
Clearance
Grip to Door Proj.
Prod.
No.
VR900
7-1/4"
11"
2" W X 10" H
1-1/2"
VR900LLP 5-1/4"
C16
1-7/8"
Width
Height
Thru-Bolt
Pattern
Clearance
Grip to Door Proj.
11"
1-3/4" W X 10" H
1-1/2"
1-7/8"
Vandal Resistant Trim
VR910-DT
VR910-NL
• For use with Von Duprin 98/99 Series Rim and Vertical
exit devices.
• Thru-bolts directly to device.
• Pull operation only. No cylinder cutout.
• For use with Von Duprin 98/99 Series Rim and Vertical
exit devices.
• Thru-bolts directly to device.
• Includes cylinder cutout.
• Tailpiece guide and cylinder cup provided.
Prod.
No.
Width
Height
Thru-Bolt
Pattern
Clearance
Grip to Door Proj.
Prod.
No.
Width
Height
Thru-Bolt
Pattern
Clearance
Grip to Door Proj.
VR910DT
5-1/4"
11"
1-3/8" W X 7" H
1-1/2"
VR910NL
5-1/4"
11"
1-3/8" W X 7" H
1-1/2"
1-7/8"
VR910M-NL RHR
VR910M-NL LHR
VR910M-DT
•
•
•
•
1-7/8"
For use with Von Duprin 98/9975 Series Mortise exit devices.
Thru-bolts directly to device.
Includes built-in lock protector.
Pull operation only. No cylinder cutout.
• For use with Von Duprin 98/9975 Series Mortise exit devices.
• Thru-bolts directly to device.
• Includes built-in lock protector and cylinder cutout.
Prod.
No.
Width
Height
Thru-Bolt
Pattern
Clearance
Grip to Door Proj.
Prod.
No.
VR910M-DT
7-1/4"
11"
1-3/8" W X 7" H
1-1/2"
VR910M-NL 7-1/4"
1-7/8"
Width
Height
Thru-Bolt
Pattern
Clearance
Grip to Door Proj.
11"
1-3/8" W X 7" H
1-1/2"
1-7/8"
C17
Notes
C18
Section D
Floor Stops,
Wall Stops and Bumpers
Floor Stops - Dome
FS13 Dome Stop
Features:
• Standard FS13 for use where no threshold is used.
• Heavy-Duty Cast Dome Stops constructed of brass.
• Unique riser design of R14 (below) allows easy conversion to
threshold application.
• Units are packed with fasteners sufficient for mounting in all types
of floor construction, including concrete.
• Meets ANSI/BHMA 156.6, L12141.
• Finishes: US3, US4, US10, US10B, US26 and US26D.
Product No.
Overall Height
Base Height
Base Diameter
FS13
1"
5
⁄32"
13⁄4" round
FS13 x R14 pictured
FS17 Dome Stop
Features:
• One piece dome stop for use with thresholds.
• Heavy-Duty Cast Dome Stops constructed of brass.
• Units are packed with fasteners sufficient for mounting in all
types of floor construction, including concrete.
• Meets ANSI/BHMA 156.1, L12161.
• Finishes: US3, US4, US10, US10B, US26 and US26D.
Product No.
Overall Height
Base Height
Base Diameter
FS17
1 ⁄32"
1
⁄2"
13⁄4" round
11
R14 Riser
Features:
• Adapts the FS13 Dome Stop to threshold use.
• Brass Die Cast Construction.
• Meets ANSI/BHMA 156.1, L12161 when used with
FS13 Dome Stop.
• Finishes: US3, US4, US10, US10B, US26 and US26D.
Product No.
Riser Height
Base Diameter
R16
5
⁄16"
13⁄4" round
D1
Floor Stops – Dome
FS436 Dome Stop
Features:
• For doors without threshold.
• Heavy-Duty Cast Dome Stops constructed of brass, bronze or aluminum.
• Gray, non-marring rubber bumper.
• Packed with wood screw and plastic anchor, specify Tampin (TPN) or lead expansion
shield (LS), if required.
• Meets ANSI/BHMA 156.6, L12141 for brass or bronze and L32141 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D and US28.
Product No.
FS436
Overall Height
Base Height
Base Diameter
1"
3/16"
1-3/4" x 2" Oval
R435 Riser
Features:
• Extruded aluminum, mill finish.
1"
• For conversion of FS436 Dome Stop to carpet installation.
• Packed with wood screws, lead shield and stud. Specify
Tampin (TPN) if required.
1-7/16"
• Available in 1/4", 3/8", 1/2", 5/8", 3/4" and 1" height.
Product No.
Size
R435
1" x 1-3/8" Oval
1" OR
LESS
PAD
FLOOR
How to Order:
FS ___ - ___ - ___ - ____
Model:
436
Dome Stop Only
435
Riser Only
436 x 435 Dome Stop & Riser
Riser Size:
Blank
1/4
3/8
1/2
5/8
3/4
1
No riser
for 1/4"
for 3/8"
for 1/2"
for 5/8"
for 3/4"
for 1"
Finishes:
US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28
Mounting:
Blank
TPN
LS
D2
Standard
Tampin
Lead Expansion Shield
Floor Stops – Dome
FS438 Dome Stop
Features:
• For doors with threshold or undercut doors.
• Heavy-Duty Cast Dome Stops constructed of brass, bronze or aluminum.
• Gray, non-marring rubber bumper.
• Packed with wood screw and plastic anchor, specify Tampin (TPN) or lead expansion
shield (LS), if required.
• Meets ANSI/BHMA 156.6, L12141 for brass or bronze and L32141 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
FS438
Overall Height
Base Height
Base Diameter
1-3/8"
9/16"
1-3/4" x 2" Oval
R437 Riser
Features:
1"
• Extruded aluminum, mill finish.
• For conversion of FS438 Dome Stop to carpet installation.
1-7/16"
• Packed with wood screws, lead shield and stud. Specify
Tampin (TPN) if required.
1" OR
LESS
• Available in 1/4", 3/8", 1/2", 5/8", 3/4" and 1" height.
Product No.
Size
R437
1" x 1-3/8" Oval
PAD
FLOOR
How to Order:
FS ___ - ___ - ___ - ____
Model:
438
Dome Stop Only
437
Riser Only
438 x 437 Dome Stop & Riser
Riser Size:
Blank
1/4
3/8
1/2
5/8
3/4
1
No riser
for 1/4"
for 3/8"
for 1/2"
for 5/8"
for 3/4"
for 1"
Finishes:
US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28
Mounting:
Blank
TPN
LS
Standard
Tampin
Lead Expansion Shield
D3
Floor Stops
FS18S
FS18L
Features:
• Security Door Stops designed for use in high
vandalism areas.
• Molded from flame resistant, resilient
material around a heavy-duty stud.
• Once grouted in concrete, leaves no exposed
fasteners to be tampered with or removed.
• Ideal for jail or security cell areas
where floor mounted stops are required.
• FS18L also ideal for concrete wall applications.
• Finish: Black.
Product No.
Stop Height
Stop Diameter
Stud Length
FS18S
FS18L
1-1/2"
3-1/2"
2"
2"
2-1/2"
2-1/2"
FS434
Features:
• Burnished wrought steel.
• Soft, resilient gray rubber.
• For undercut doors up to 1-1/2".
• Packed with screws and plastic anchors.
• Finishes: US2C, US10.
Product No.
Overall Height
Base Size
FS434
2-5/8"
1-1/2" W x 2-3/4" L
D4
FS18S
FS18L
Floor Stops
FS441
Features:
• Designed to blend well with all types of construction and provide a minimum of
hindrance to cleaning efforts.
• Accommodates door undercut up to 1-1/2".
• Heavy-Duty cast brass or aluminum construction.
• Non-marring rubber bumper.
• FS441 packed with expansion shield and tampin.
• FS441-WS packed with wood screws.
• FS441 meets ANSI/BHMA 156.16, L12131 for brass and L32131 for aluminum.
FS441-WS meets ANSI/BHMA 156.16, L12121 for brass and L32121 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
Overall Height
Overall Length
Base Depth
FS441-MS
FS441-WS
2-1/8"
2-1/8"
2-7/8"
2-7/8"
1-5/8"
1-5/8"
FS442
Features:
• Designed to blend well with all types of construction and provide a minimum of
hindrance to cleaning efforts.
D
E
U
N
I
T
N
O
C
DIS
• Accommodates door undercut up to 2".
• Heavy-Duty cast brass or aluminum construction.
• Non-marring rubber bumper.
• FS442 packed with expansion shield and tampin.
• FS442-WS packed with wood screws.
• FS442 meets ANSI/BHMA 156.16, L12131 for brass and L32131 for aluminum.
FS442-WS meets ANSI/BHMA 156.16, L12121 for brass and L32121 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
Overall Height
Overall Length
Base Depth
FS442
FS442-WS
2-7/8"
2-7/8"
2-3/4"
2-3/4"
1-5/8"
1-5/8"
D5
Floor Stops
FS444
Features:
• Ideal for interior or exterior use.
• Cast brass construction.
• Accommodates door undercut up to 2-1/2".
• Non-marring rubber tip.
• Packed with expansion shield and lead shield.
• Meets ANSI/BHMA 156.16, L12131 for brass, and L32131 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
Overall Height
Base Diameter
FS444
3"
2-1/2"
FS448
Features:
• Ideal for interior or exterior use.
• Cast brass construction.
• Accommodates door undercut up to 2-1/2".
• Non-marring rubber tip.
• Packed with wood screws.
• Meets ANSI/BHMA 156.16, L12121, for brass and L32121 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
Overall Height
Base Diameter
FS448
3"
2-1/2"
D6
Floor Door Stop & Manual Holder
FS446
Features:
• Manual type floor holder ideal for interior or exterior use.
• Cast brass or aluminum construction.
• Accommodates door undercut up to 2-1/2".
• Non-marring rubber tip.
• Unit functions as a stop but serves as a Hold-Open device when hook is manually engaged in
strike. Unit requires manual disengagement to release Hold-Open.
• Packed with expansion shield and lead shield.
• Meets ANSI/BHMA 156.16, L11371 for brass and L31371 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product
No.
Overall
Height
Height from Floor
to Stop Center Line
Stop
Diameter
Base
Diameter
FS446
3-3/4"
2-5/8"
1-1/16"
2-1/2"
FS450
Features:
• Manual type floor holder ideal for interior or exterior use.
• Cast brass or aluminum construction.
• Accommodates door undercut up to 2-1/2".
• Non-marring rubber tip.
• Unit functions as a stop but serves as a Hold-Open device when hook is manually engaged
in strike. Unit requires manual disengagement to release Hold-Open.
• Packed with wood screws.
• Meets ANSI/BHMA 156.16, L11361 for brass and L31361 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product
No.
Overall
Height
Height from Floor
to Stop Center Line
Stop
Diameter
Base
Diameter
FS450
3-3/4"
2-5/8"
1-1/16"
2-1/2"
FS451
Features:
• Manual type door holder ideal for interior or exterior use.
• Cast brass construction.
D
E
U
N
I
T
N
O
C
DIS
• Strike features hinged hook which engages the holder.
• Accommodates door undercut up to 2-1/2".
• Resilient rubber tip.
• FS451-WS packed with wood screws.
• FS451 packed with expansion shield and tampin. Strike packed with sheet metal screws.
• FS451-WS meets ANSI/BHMA 156.16, L11361 for brass and L31361 for aluminum. FS451-WS
meets ANSI/BHMA 156.16, L11371 for brass and L31371 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
Overall Height
Base Depth
Base Width
FS451-WS
FS451
3-3/16"
3-3/16"
2-1/2"
2-1/2"
1-5/8"
1-5/8"
D7
Floor Door Stop & Semi-Automatic Holder
FS9
Features:
• Semi-automatic floor-mounted holders accommodates with door to floor clearance
of 1-1/2" or less.
• Cast from heavy-duty brass.
• Activate holder by flipping the engagement tongue forward. When door is opened,
the hook (mounted on door) engages the tongue. To release, push firmly on door
to disengage tongue.
• Universal screw pack accommodates all types of floor and door construction.
• Meets ANSI/BHMA 156.16, L11241.
• Finishes: US3, US4, US10, US10B, US26 and US26D.
Product No.
Overall Height
Base Dimension
FS9
3-1/2"
2" Wide x 3-1/2" Long
D8
Floor Door Stop & Automatic Holder
FS40
FS41
FS42
FS43
Features:
• Automatic door holders ideal for heavy-traffic situations that require a simple,
fool-proof, Hold-Open device.
• Forged from brass.
• Unit is activated automatically when door is opened. A firm pull on door releases
the mechanism.
• Strikes accommodate different door to floor clearances.
• Model numbers are determined by strike/door-to-floor clearances.
• Holder position on door is adjustable.
• Universal screw pack allows for installation in all types of door construction.
• Meets ANSI/BHMA 156.16, L11301.
• Finishes: US3, US4, US10, US10B, US26, US26D.
Product No.
Door to Floor Clearance
Holder Dimensions
FS40
FS41
FS42
FS43
1/2" or less
9/16" to 1-1/16"
1-1/8" to 1-9/16"
1-5/8" to 2-1/16"
3" Wide x 3-11/16" High
3" Wide x 3-11/16" High
3" Wide x 3-11/16" High
3" Wide x 3-11/16" High
FS40
Optional Strike Details
FS42
FS41
FS43
D9
Floor Door Stop & Automatic Holder
FS495
Features:
• Automatic door holders ideal for heavy-traffic situations that require a simple, Hold-Open device.
• Cast brass construction.
• Holds door 3-3/4" from wall.
• Recommended installation is holder on door and strike on wall.
• Holder position on door is adjustable.
• Holder is tapered to prevent “child riding.”
• Meets ANSI/BHMA 156.16, L11291 for brass.
• Finishes: US3, US4, US10, US10B, US26, US26D.
FS496
Features:
• Cast brass construction.
• For door to floor clearances of 3/8" maximum.
• Meets ANSI/BHMA 156.16, L11301 for brass.
• Finishes: US3, US4, US10, US10B, US26, US26D.
FS497
Features:
• Cast brass construction.
• For door to floor clearances of 1" maximum.
• Meets ANSI/BHMA 156.16, L11301 for brass.
• Finishes: US3, US4, US10, US10B, US26, US26D.
D10
Plunger Type Door Holders
FS1153
Features:
• Provides a contemporary yet economical method of positive Hold-Open.
• Constructed in sturdy cast aluminum.
• Spring operated plunger activates with minimal pressure, releasing instantly with a
light tap on the plat-form lever.
• Provides a 1-5/8" throw for all types of doors.
• Ribbed non-marring rubber shoe is securely fastened to unit with a screw and is
easily replaced when worn.
• Meets ANSI/BHMA 156.16, L31401.
• Finish: US28.
Product No.
Height
Width
Depth
FS1153
6-1/4"
1-1/2"
1-7/16"
FS1154
Features:
• Constructed from heavy-duty cast brass or bronze.
• Plunger and internal parts are plated steel and provides a 1-1/4" throw for all types of
doors.
• Plunger is easily activated with minimal pressure, releasing instantly with a light tap on
the platform lever.
• Round non-marring rubber shoe is securely fastened with a screw in flanged cup to
prevent movement or loss. When worn, shoes are easily replaced.
• Meets ANSI/BHMA 156.16, L11401.
• Finishes: US3, US4, US10, US10B, US26, US26D.
Product No.
Height
Width
Depth
FS1154
5-1/2"
2"
1-1/4"
D11
Kick Down Holders
FS452
Features:
• Units provide simple hold and release, activated with a touch of the foot.
• Cast brass or aluminum construction.
• Stainless steel spring.
• Non-marring rubber shoes have corrugated bottoms to provide secure grip.
• Shoes are easily replaced when worn.
• FS452-4 has a door-to-floor clearance of 2" or less. FS452-5 has a door-to-floor clearance up to 3".
• Packed with sheet metal screws.
• Meets ANSI/BHMA 156.16, L11383 for brass and L31383 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D. FS452-4 also available is US28.
Product No.
Door-to-Floor
Clearance
Plate
Height
Plate
Width
FS452-4
FS452-5
2" or less
Up to 3"
2-1/8"
2-1/8"
1"
1"
FS455
Features:
• Units provide simple hold and release, activated with a touch of the foot.
• Cast brass or aluminum construction.
• Non-marring rubber shoes have corrugated bottoms to provide secure grip and a shank which forms
its own thread when screwed into threaded cavity of holder. When worn, shoes are easily replaced.
• Door-to-floor clearances of 2" or less.
• Meets ANSI/BHMA 156.16, L11382 for brass and L31382 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US3AL, US10AL,
US27/A92.
Product No.
Door-to-Floor
Clearance
Plate
Height
Plate
Width
FS455
2" or less
1-3/4"
1-3/4"
FS544
FS555
Features:
• Units provide an economical method to hold open doors.
• Cast of durable iron.
• Non-marring rubber shoes have corrugated bottoms to provide secure grip. Rubber shoe is
securely fastened with screw. When worn, shoes are easily replaced.
• FS544 for door-to-floor clearances of 2" or less. FS555 for door-to-floor clearances up to 3".
• FS544 meets ANSI/BHMA 156.16, L11381. FS555 meets ANSI/BHMA 156.16, L11391.
• Finishes: SP4, SP10, SP313, SP28, SPBLK.
Product No.
Door-to-Floor
Clearance
Plate
Height
Plate
Width
FS544
FS555
2" or less
Up to 3"
2-1/4"
2-1/4"
1-7/16"
1-7/16"
D12
Wall Bumpers
WS401 CVX & WS402 CVX
WS401 CCV & WS402 CCV
Features:
• Constructed in heavy-duty cast brass or aluminum base.
• Special retainer cup makes rubber tamper resistant.
• The WS401CVX unit is designed with a convex rubber bumper, packed with wood screw and
plastic anchor.
• The WS401CCV unit is designed with a concave rubber bumper which avoids damage to
locks with projecting buttons, packed with wood screw and plastic anchor.
• The WS402CVX unit is designed with a convex rubber bumper packed with screw and
drywall anchor.
WS401CVX & WS402CVX
• The WS402CCV unit is designed with a concave rubber bumper which avoids damage to
locks with projecting buttons and is packed with screw and drywall anchor.
• WS401CVX & WS402CVX meets ANSI/BHMA 156.16 L12101 for brass and L32101
for aluminum.
• WS401CCV & WS402CCV meets ANSI/BHMA 156.16 L12251 for brass and L32251
for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
WS401CVX
WS401CCV
WS402CVX
WS402CCV
Mounting
Hardware
Wood screw,
plastic anchor
Wood screw,
plastic anchor
Screw, Drywall
Anchor
Screw, Drywall
Anchor
Base
Diameter
Base
Thickness
Overall
Projection
2-1/2"
3/8"
1"
2-1/2"
3/8"
1"
2-1/2"
3/8"
1"
2-1/2"
3/8"
1"
WS401CCV & WS402CCV
WS404CVX
Features:
• Constructed in cast brass.
• Compact size.
• Totally concealed mounting discourages vandalism or tampering.
• Unit furnished with grey convex rubber bumper.
• Packed with sheet metal screw, rawl plug and brad.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
Base
Diameter
Overall
Projection
WS404CVX
1"
17/32"
D13
Wall Bumpers
WS406CVX & WS407CVX
WS406CCV & WS407CCV
Features:
• Constructed in sturdy yet economical wrought base of brass, aluminum or stainless
steel construction.
• Feature concealed tamper-proof mounting.
• Shipped factory preassembled backplate to reduce installation cost.
• Easy installation by inserting screwdriver through small hole in rubber.
• The WS406CVX unit is designed with a convex rubber bumper, packed with wood screw and
plastic anchor.
WS406CVX & WS407CVX
• The WS406CCV unit is designed with a concave rubber bumper, which avoids damage to
locks with projecting buttons, packed with wood screw and plastic anchor.
• The WS407CVX unit is designed with a convex rubber bumper packed with screw and
drywall anchor.
• The WS407CCV unit is designed with a concave rubber bumper which avoids damage to
locks with projecting buttons and is packed with screw and drywall anchor.
• WS406CVX & WS407CVX meets ANSI/BHMA 156.16 L22201 for brass, L42101 for
aluminum and L52101 for stainless steel.
• WS406CCV &WS407CCV meets ANSI/BHMA 156.16 L22251 for brass and L42251 for
aluminum, and L52251 for stainless steel.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28, US32D.
Product No.
WS406CVX
WS406CCV
WS407CVX
WS407CCV
D14
Mounting
Hardware
Wood screw,
plastic anchor
Wood screw,
plastic anchor
Screw, Drywall
Anchor
Screw, Drywall
Anchor
Base
Diameter
Base
Thickness
Overall
Projection
2-1/2"
3/8"
1"
2-1/2"
3/8"
1"
2-1/2"
3/8"
1"
2-1/2"
3/8"
1"
WS406CCV & WS407CCV
Wall Bumpers
408
Features:
• Constructed in sturdy yet economical wrought base of brass or stainless steel.
D
E
U
N
I
T
N
O
C
DIS
• Factory assembled backplate.
• Concealed mounting.
• Easy installation by inserting screw through small hole in rubber.
• Meets ANSI/BHMA A156.16, L22251 for brass and L52251 for stainless steel.
• 408 unit has convex rubber bumper and is packed with machine screw and expansion shield.
408
• Finishes: B10, B26D, PA28 and S32D.
Product No.
Base
Diameter
Base
Thickness
Overall
Projection
408
2-7/16"
3/8"
1"
408 1/2 & 409 1/2
Features:
• Constructed in sturdy yet economical wrought base of brass, aluminum, or stainless steel.
• Factory assembled backplate.
• Concealed mounting.
• Easy installation by inserting screw through small hole in rubber.
• Meets ANSI/BHMA A156.16, L22251 for brass, L42251 for aluminum, and L52251 for stainless steel.
• 408-1/2 is packed with machine screw and expansion shield.
• 409-1/2 is packd with plastic drywall anchor and screw for hollow and solid walls.
• 408-1/2 Finishes: B10, B26D, PA28, and S32D.
• 409-1/2 Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, PA28 and S32D.
D
E
U
N
I
T
N
O
C
DIS
Product No.
Base
Diameter
Base
Thickness
Overall
Projection
408 1/2
409 1/2
2-7/16"
1-7/8"
3/8"
3/8"
15/16"
1-1/16"
409 1/2
411R
Features:
•
•
•
•
Adhesive-backed wall door stop for use on clean, smooth, flat surfaces only.
Non-marring rubber available in gray or white.
Concave design permits knob to strike stop without damaging or engaging lock mechanism.
Finishes: Specify G (gray rubber) or W (white rubber).
Product No.
411R
Base
Diameter
Base
Thickness
Overall
Projection
1-7/8"
3/8"
1-1/16"
411R
D15
Wall Stops
WS11
WS11X
Features:
• Constructed in heavy duty cast brass.
• WS11 is furnished with 3 countersunk mounting holes for drywall mounting.
• WS11X is furnished with a threaded stud and expansion shield for masonry type mounting.
• Hexagon section on unit aids in fastening unit when expansion shield is used.
• Rubber bumpers features off-set shoulder and threaded shank that screws into body of unit.
• WS11 meets ANSI/BHMA 156.16, L12011 WS11X meets ANSI/BHMA 156.16, L12021.
• Finishes: US3, US4, US10, US10B, US26, US26D.
Product No.
Base
Diameter
Overall
Projection
WS11
WS11X
2"
2"
3-3/4"
3-3/4"
WS33
WS33X
Features:
• Constructed in a durable cast brass.
• Sturdy rubber bumper with offset shoulder screws into cavity on body to prevent loss or theft.
• Sloping design discourages vandalism
• WS33 is furnished with 3 mounting holes for drywall mounting.
• WS33X is furnished with a threaded stud and expansion shield for masonry type mounting.
• Finish: US26D.
Product No.
Base
Height
Base
Width
Overall
Projection
WS33
WS33X
3"
3"
2-1/4"
2-1/4"
3-3/4"
3-3/4"
WS65
Features:
• Burnished cast aluminum.
• Non-marring rubber bumper.
• Packed with sheet metal screws.
• Finishes: US3, US10AL, A10B, US27.
Product No.
Base
Diameter
Overall
Projection
WS65
1-5/8"
3-3/4"
D16
Wall Stops
WS443
Features:
• Constructed in brass.
• Ideal for interior or exterior use.
• Non-marring rubber tip.
• Packed with expansion shield and lead shield.
• Meets ANSI/BHMA 156.16, L12021 for brass and L32021 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
Base
Diameter
Overall
Projection
WS443
2-1/4"
3-11/16"
WS447
Features:
• Constructed in brass or aluminum.
• Ideal for interior or exterior use.
• Non-marring rubber tip.
• Furnished with 3 mounting holes for drywall mounting.
• Packed with wood screws.
• Meets ANSI/BHMA 156.16, L12011 for brass and L32011 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product No.
Base
Diameter
Overall
Projection
WS447
2-1/4"
3-11/16"
D17
Manual Wall Holders
WS20
WS20X
Features:
• Constructed in cast brass.
• WS20 is furnished 3 countersunk mounting holes for drywall mounting.
• WS20X is furnished with threaded stud for masonry type mounting.
• Rubber bumpers feature off-set shoulder and threaded shank that screws
into body of holder.
• Hinged strike furnished matches body material and finish.
WS20 Shown
• WS20 meets ANSI/BHMA 156.16, L11341 WS20X meets ANSI/BHMA
156.16, L11351
• Finishes: US3, US4, US10, US10B, US26, US26D.
Product No.
Base
Diameter
Overall
Projection
Strike
Height
Strike
Width
WS20
WS20X
2-3/8"
2-3/8"
4"
4"
2"
2"
1"
1"
WS445
Features:
• Constructed in cast of brass or aluminum.
• Unit functions as a stop but serves as a Hold-Open device when hook is manually
engaged in strike.
• Unit requires manual disengagement to release Hold-Open.
• Resilient, non-marring rubber tip.
• Packed with expansion shield and lead shield.
• Meets ANSI/BHMA 156.16, L11351 for brass and L31351 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product
No.
Base
Diameter
Base
Projection
Engaged
Projection
Strike
Height
Strike
Width
Strike
Projection
WS445
2-1/4"
3-11/16"
5-3/4"
1-1/2"
13/16"
13/16"
WS449
Features:
• Constructed in cast of brass or aluminum.
• Unit functions as a stop but serves as a Hold-Open device when hook is manually
engaged in strike.
• Unit requires manual disengagement to release Hold-Open.
• Resilient, non-marring rubber tip.
• Packed with wood screws.
• Meets ANSI/BHMA 156.16, L11341 for brass and L31341 for aluminum.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.
Product
No.
Base
Diameter
Base
Projection
Engaged
Projection
Strike
Height
Strike
Width
Strike
Projection
WS449
2-1/4"
3-11/16"
5-3/4"
1-1/2"
13/16"
13/16"
D18
Automatic Wall Holders
WS40
Features:
• Constructed of sturdy cast brass, or aluminum.
• Holder is mounted on wall and strike is mounted on door.
• Roller on holder rides up seats itself on strike, with a heavy duty bumper pad
deadening the sound and shock.
• Universal screw pack accommodates all types wall construction.
• Meets ANSI/BHMA 156.16, L11291.
• Finishes: US3, US4, US10, US10B, US26, US26D, US28.
Product
No.
Base
Height
Base
Width
Base
Projection
WS40
2"
2-1/2" 2-1/4"
Engaged
Projection
Strike
Height
Strike
Width
Strike
Projection
3-1/2"
2-1/16"
3/4"
2"
WS45
WS45X
Features:
• Constructed of cast brass, bronze or aluminum.
• Spring loaded roller rides up the face of the strike, seating itself on the
strike, holding the door firmly in the open position.
• A heavy rubber pad cushions the shock and absorbs the sound.
• With unit mounted on door and the strike on wall, vertical adjustment is
available on body.
• The strike is adjustable 45 degrees left or right, both adjustments easily
accomplished at time of installation or at a later date.
• WS45 strike is furnished with 3 countersunk mounting holes.
• WS45X strike is furnished with a threaded stud and expansion shield for
masonry type mounting.
• Meets ANSI/BHMA 156.16, L11291.
• Finishes: US3, US4, US10, US10B, US26, US26D, US28.
Product
No.
Base
Height
Base
Width
Base
Engaged
Projection Projection
Strike
Diameter
Strike
Projection
WS45
WS45X
3-11/16"
3-11/16"
3"
3"
2"
2"
2-3/8"
2-3/8"
3"
3"
3-7/16"
3-7/16"
D19
Roller Bumpers
RB470
RB471
B
A
A
RB470
RB471
RB472
Features:
• Constructed in heavy-duty cast brass.
• RB470 used where two doors open against each other to prevent damage
to the doors or hardware.
RB471
• RB471 and RB472 are ideal for use in situations where doors meet each
other at approximate right angles (back to back).
• RB470 meets ANSI/BHMA 156.16, L12212 RB471 meets ANSI/BHMA
156.16, L12192 RB472 meets ANSI/BHMA 156.16, L12202.
• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26,
US26D.
Product No.
Base
Size
Arm
Offset (B)
Overall
Length (A)
RB470
RB471
RB472
1-11/16" x 2-1/4"
2" Dia.
2" Dia.
2-3/4"
––
—
5"
4-1/2"
6"
D20
A
Door Silencers
SR64
SR65
SR66
Features:
Features:
Features:
• For use on metal frames featuring
pneumatic design that, once installed,
forms an air pocket to absorb shock
and reduce noise of door closing.
• For use on wood frames, also feature
pneumatic design to cushion shock and
absorb noise.
• Self Adhesive Rubber Silencers.
• To prevent removal, a small brad should
be driven into stop strip and through
stem of silencer, as shown in the detail.
• Packed in sheets of 100.
• Tamper-proof once installed on the frame.
• Proper installation also eliminates door
rattle and provides constant tension for
door latches or locks.
• Packed in bags of 100. Grey also available
in bulk pack of 2500.
• Economical installation requires no
drilling of frames.
• Finishes: brown, grey, white.
• Packed in bags of 100.
• Meets ANSI/BHMA 156.16, L03021
• Finish: grey.
• Each bag has an installation tool included.
• Meets ANSI/BHMA 156.16, L03011.
• Finish: grey is standard. Black optional.
Product No.
Diameter
Thickness
Product No. Height
Width
Thickness
Product No.
Diameter
Thickness
SR64
1/2"
1/8"
SR64
3/8"
1/8"
SR66
1/2"
1/8"
3/4"
D21
Residential Door Stops
060 and 061 Flexible Door Stops
Features:
• Utilizes heavy gauge spring to maintain rigid protections.
• Simple to install - only a screwdriver required.
• Rubber tip is replaceable.
• Made from burnished wrought steel.
• Meets design requirements of ANSI/BHMA A156.16.
• Packed disassembled for quick installation.
• Finishes: F3, F5, F10, F10B, F14, F26, F26D.
Product Number
Projection
060
061
3"
4"
060
061
60, 61 and 62 Base Door Stops
Features:
• Available in three sizes to accommodate varying areas of installation and door
trim dimensions.
• Rubber tip is replaceable.
60 Base Door Stop
• Projection: 3-3/4".
• Made from solid brass or aluminum.
• Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A
(B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92.
61 Base Door Stop
• Projection: 3-1/8" on brass units. 3-3/16" on aluminum units.
• Made from solid brass, aluminum, or epoxy colored aluminum.
• Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A
(B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92, A-A
(Almond Epoxy Coated), A-W (White Epoxy Coated), A-BLK (Black Epoxy
Coated).
62 Base Door Stop
D
• Projection: 4-1/2".
UE
TIN
• Made from solid brass or aluminum.
N
CO
• Finishes: B3 (B-605),
DIS B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A
(B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92.
60
61
062 Base Door Stop
Features:
• Base Door Stop features one-piece styling.
• Designed with a flat surface to accommodate wrench or pliers when
installing.
• Rubber tip is replaceable.
• Made from solid brass or aluminum.
• Meets ANSI/BHMA A156.16.
• Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A
(B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92.
D
E
U
N
I
T
N
O
C
DIS
Product Number
Projection
062
2-1/2"
D22
Residential Door Stops
64 Base Door Stop
Features:
• Base Door Stop features deluxe one-piece styling.
• Easily screws into base.
• Designed with square head to accommodate wrench or pliers when installing.
• Rubber tip is replaceable.
• Made from solid brass or aluminum.
• Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A (B-620), B26
(B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92.
Product Number
Projection
64
3-1/4"
430 Floor Door Stop
Features:
• One-piece design easily screws into floor.
• Rubber tip is replaceable.
• Made from solid brass or aluminum.
• Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A (B-620), B26
(B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92.
Product Number
Base Diameter
Height
430
1-1/4"
1-5/16"
69 Hinge Pin Door Stop
Features:
• For use on hinged doors where the installation of a standard door stop is not desirable.
• Positive slip proof adjustment.
• Non-marring rubber tips.
• Removable bushings accommodate 1/4" to 5/16" diameter hinge pins.
• Easy installation—only a screwdriver required.
• Made from burnished wrought steel.
• Finishes: F3, F5, F10, F10B, F14, F15, F15A, F26, F26D.
Product Number
Door Openings Adjustments
69
70° to 100°
70 Hinge Pin Door Stop
Features:
• For use on hinged doors where the installation of a standard door stop is not desirable.
• Designed for narrow trim installation.
• High quality rubber bumpers - shoulder on stud supports rubber through entire body for
engineered cushioning.
• Replaceable, non-marring rubber tips.
• Removable bushings accommodate 1/4" to 5/16" diameter hinge pins.
• Easy installation.
• Made from solid brass, aluminum, or epoxy coated aluminum.
• Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14, B15 (B-619), B15A
(B-620), B26 (B-625), B26D, A3, A4, A5, A10, A10B, A14, A26, A92, A-A (Almond Epoxy Coated),
A-W (White Epoxy Coated), A-BLK (Black Epoxy Coated).
Product Number
Door Openings Adjustments
70
85° to 125°
D23
Notes
D24
Section E
Surface Bolts,
Dutch Door Bolts and
Door Guards
Surface Bolts
SB1600
•
•
•
•
•
•
•
•
•
•
•
•
•
Standard Surface Bolt has 1" throw for maximum security.
Ideal for all types of doors.
Fully concealed mounting prevents vandalism.
Available in locking version. Unit locks in both the up and down
position. Locking Bolts are furnished with 2 keys in 4 keying variations.
Units packed with wood and machine screws to meet most field conditions.
Units available with either a universal top strike (T) or a flat bottom strike (B).
1630 Series is constructed of heavy duty steel.
1640 Series is constructed of brass.
1630 Series is UL listed up to 3 hours when used on the inactive door of a
pair up to 8' in height.
1630 meets ANSI/BHMA A156.16, L84161.
1640 meets ANSI/BHMA A156.16, L24161.
Finishes: 1630 – US2G, US10B, US26D
1640 – US3, US10B, US26D
Optional sex bolts available.
Dimensions:
Body: 8" Long x 7/8" Wide x 3/4" Thick,
Overall Knob or Lock Housing Projection: 1-1/2"
Top Strike: 1-1/4" Wide x 7/8" Tall x 15/16" Deep
Bottom Strike: 3" Long x 1" Wide x 1/8" Thick
How to Order:
SB16 _____ _____ _____ - _____ - _____
Model:
30
40
Steel
Brass
Strike:
T
B
TB
Universal Top Strike
Flat Bottom Strike
Both Strikes, 1630 only
Type:
Blank
L
Standard Bolt
Locking Bolt
Key Code:
Locking only (1289, 1360, 1390, 1395)
Finishes:
1630
1640
US2G, US10B, US26D,
US3, US10B, US26D
E1
Surface Bolts
SB1600M1
SB1600M2
• Standard Surface Bolt has 3-1/2" throw for maximum security and for doors with
larger undercuts.
• Sleek handle design.
• Ideal for all types of doors.
• Fully concealed mounting prevents vandalism.
• Available in locking version. Unit locks in both the up and down position. Locking
bolts are furnished with 2 keys in 4 keying variations.
• Units packed with wood and machine screws to meet most field conditions.
• Units available with either a universal top strike (T) or a flat bottom strike (B).
• Constructed of heavy duty steel.
• UL listed up to 3 hours when used on the inactive door of a pair up to 8' in height.
• Finishes: SP4, SP10, SP28, SP313, SPBLK.
• Optional Sex Bolt available.
SB1600M1
SB1600M2
Dimensions:
Bar: 11" Long x 3/4" Wide x 3/4" Thick, locking
version 1-1/2" Thick
Top Strike: 1-1/4" Wide x 7/8" Tall x 15/16" Deep
Bottom Strike: 3" Long x 1" Wide x 1/8" Thick
How to Order:
SB1600 _____ _____ _____ - _____ - _____
Model:
M1
M2
Handle Up
Handle Down
Strike:
T
B
Universal Top Strike
Bottom Strike
Type:
Blank
L
Standard Bolt
Locking Bolt
Key Code:
Locking only (1289, 1360, 1390, 1395)
Finishes:
SP4, SP10, SP28, SP313, SPBLK
E2
Surface Bolts
SB360
Features:
• Surface Bolt has 1-1/4" throw for maximum security.
• Jimmy-resistant design, bolt locks automatically when thrown, can be released only
be pressing knob toward door while retracting.
• Ideal for all types of doors.
• Available in 12" or 24" lengths.
• Unit locks in both the up and down position.
• Accepts padlock (not furnished) with maximum 3/8" diameter shackle, minimum
1-3/4" shackle opening height.
• Units packed with one-way screws for added security. Standard screws also supplied.
• Units available with either a universal top strike (T) or a flat bottom strike (B).
• Constructed of heavy duty steel.
• 12" Bolt is UL listed up to 3 hours when used on the inactive door of a pair up to
10' in height.
• Meets ANSI/BHMA A 156.16.
• Finish: US2C
• Optional Sex Bolts available.
• Optional Mortise Strike available.
Dimensions:
Bar: 3/4" Wide x 3/4" Thick
Overall Width: 2-1/32"
Overall Projection: 2-1/16"
Top Strike: 1-1/2" x 1-1/2" Angle, 3/16" Thick
Optional Mortise Strike: 3-1/2" Long x 1-5/8"
Wide x 1/8" Thick
How to Order:
SB360 - _____ - _____ - _____
Length:
12
24
For 12" bolt
For 24" bolt
Strike:
T
Universal Top Strike (standard)
Finish:
US2C
E3
Surface Bolts
SB453
•
•
•
•
•
•
•
•
•
•
•
•
Surface Bolt has 1-3/16" throw for maximum security.
Strong tension springs prevent creep.
Ideal for all types of doors.
Available 8", 12", 18" or 24" lengths.
Units packed with standard screws for added security.
Units packed with both a universal top strike (T) and a mortise bottom strike (B).
Constructed of heavy duty steel.
8" and 12" Bolts are UL listed up to 3 hours when used on the inactive door of a
pair up to 10' in height.
Meets ANSI/BHMA A156.16 L84161
Finishes: US2C, US10, US10B, US26D.
Optional Sex Bolts available.
Optional Thru Bolts available.
Dimensions:
Bar: 3/4" Wide x 1/4" Thick
Overall Width: 2-1/32"
Overall Projection: 1-5/16"
Top Strike: 1-1/2" x 1-1/2" Angle, 3/16" Thick
Bottom Strike: 3-1/2" Long x 1-5/8" Wide x 1/8" Thick
How to Order:
SB453- _____ - _____ - _____
E4
Length:
8
12
18
24
for 8"
for 12"
for 18"
for 24"
Strike:
TB
Top and Bottom Strike
Finishes:
US2C
US26D
US10
US10B
(available in all lengths)
(available in 8" and 12" lengths)
(available in 8" length only)
(available in 8" and 12" lengths)
Surface Bolts
SB454
• Surface Bolt has 1-3/16" throw for maximum security.
• Jimmy-resistant design, bolt locks automatically when thrown, can be
released only by pressing knob toward door while retracting.
• Ideal for all types of doors.
• Available 5", 8" and 12" lengths.
• 8" and 12" units packed with both a universal top strike (T) and a mortise
bottom strike (B).
• 5" unit packed with universal top strike (T) only.
• Constructed of heavy duty steel.
• Bolts are UL listed up to 3 hours when used on the inactive door of a pair
up to 10' in height.
• Meets ANSI/BHMA A156.16 L84161
• Finishes: US2C, US10, US10B, US26D.
• Optional Sex Bolts available.
• Optional Thru Bolts available.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
Bar: 3/4" Wide x 1/4" Thick
Overall Width: 2-1/32"
Overall Projection: 1-5/16"
Top Strike: 1-1/2" x 11/2" Angle, 3/16" Thick
Bottom Strike: 3-1/2" Long x 1-5/8" Wide x 1/8" Thick
How to Order:
SB454- _____ - _____ - _____
Length:
5
8
12
for 5"
for 8"
for 12"
Strike:
T
TB
Top Strike (available in 5" length only)
Top and Bottom Strike (available in 8" or 12")
Finishes:
US2C, US10, US26D (available in all lengths)
US4
(available in 5" lengths only)
US10B (available in all lengths)
E5
Surface Bolts
SB0454
• Surface Bolt has 1-3/16" throw for maximum security.
• Jimmy-resistant design, bolt locks automatically when thrown, can be
released only by pressing knob toward door while retracting.
• Ideal for all types of doors.
• Available 5" and 8" lengths.
• Unit locks in both the up and down position.
• Accepts padlock (not furnished) with maximum 3/8" diameter shackle,
minimum 1-3/8" shackle opening height.
• Units packed with one-way screws for added security. Standard screws
also supplied.
• 8" unit packed with both a universal top strike (T) and a mortise bottom
strike (B).
• 5" unit packed with universal top strike (T) only.
• Constructed of heavy duty steel.
• Meets ANSI/BHMA A156.16 L84161
• Finishes: US2C, US26D.
• Optional Sex Bolts available.
• Optional Thru Bolts available.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
Bar: 3/4" Wide x 1/4" Thick
Overall Width: 2-1/32"
Overall Projection: 1-5/16"
Top Strike: 1-1/2" x 1-1/2" Angle, 3/16" Thick
Bottom Strike: 3-1/2" Long x 1-5/8" Wide x 1/8" Thick
How to Order:
SB0454- _____ - _____ - _____
Length:
5
8
for 5"
for 8"
Strike:
T
TB
Top Strike (available in 5" length only)
Top and Bottom Strike (available in 8" length only)
Finishes:
US2C, US26D
E6
Decorative Surface Bolts
40
• Concealed screw design enhances appearance and security.
• Exceptional strength and durability provided by interlocking
construction of heavy gauge track and rod.
• Permanent stop prevents rod disengagement from track.
• Tension spring holds bolt in desired position.
• Track assures smooth operation and interlocks with side edges of rod to
eliminate marring.
• Decorative 5/8" diameter knob designed to facilitate bolt operation.
• Made from extruded brass or aluminum.
• Available in 2", 3", 4", 6", 9" and 12" lengths.
• Packed with both Universal and Mortise Strikes. Optional Surface Strike available.
• 4" thru 12" lengths meet design requirements of ANSI/BHMA A156.16.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D, PA28.
To Order: Specify finish and length.
Dimensions:
Throw: 7/16" on 2" bolt; 15/16" on all
other lengths
Projection: 3/4"
Width: 11/16"
Length: Specify 2", 3", 4" 6", 9" or 12"
043
• Features attractive 3/8" half-round rods and well-proportioned guides.
• Semi-concealed guides assure smooth operation and are positioned under the
rod to eliminate marring the surface of the bolt.
• Stainless steel tension spring prevents rod disengagement from guide and
provides permanent spring tension to hold bolt in desired position.
• Decorative 1/2" diameter knob designed to facilitate bolt operation.
• Made from solid brass or burnished steel.
• Available in 2", 3", 4" and 6" lengths.
• Packed with both Universal and Angle Strikes. Optional Mortise Strike (MS)
available.
• Meets design requirements of ANSI/BHMA A156.16.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, F3, F5, F14.
D
E
U
N
I
T
N
O
C
DIS
To Order: Specify finish and length.
Dimensions:
Throw: 3/4"
Projection: 3/4"
Half Round Rod: 3/8"
Overall Width: 1-3/16"
Length: Specify 2", 3", 4" or 6"
43
• Features attractive 1/2" half-round rods and well-proportioned guides.
• Semi-concealed guides assure smooth operation and are positioned under
the rod to eliminate marring the surface of the bolt.
• Stainless steel tension spring prevents rod disengagement
from guide and provides tension to hold bolt in desired position.
• Decorative 3/4" diameter knob designed to facilitate bolt operation.
• Made from solid brass or burnished steel.
• Available in 4", 6", 9" and 12" lengths.
• Packed with both Universal and Angle Strikes.
• Meets design requirements of ANSI/BHMA A156.16.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, F3, F4, F5.
D
E
U
N
I
T
N
O
C
DIS
To Order: Specify finish and length.
Dimensions:
Throw: 1"
Projection: 15/16"
Half Round Rod: 1/2"
Overall Width: 1-3/8"
Length: Specify 4", 6", 9" or 12"
E7
Decorative Surface Bolts
144
• Fully concealed screw design enhances appearance and security.
• Concealed guide track assures smooth operation and is positioned under the
rod to eliminate marring the surface of the bolt.
• Stainless steel tension spring prevents rod disengagement from guide and
provides permanent spring tension to hold bolt in desired position.
• Decorative 3/4" diameter knob designed to facilitate bolt operation.
• Made from solid brass.
• Easy to install; wrench supplied for set screw.
• Available in 4", 6", 9" and 12" lengths.
• Packed with both Universal and Angle Strikes.
• Meets design requirements of ANSI/BHMA A156.16.
• Finishes: B3, B4, B5, B10B, B14, B15, B15A, B26, B26D.
D
E
U
N
I
T
N
O
C
S
I
D
To Order: Specify finish and length.
Dimensions:
Throw: 1"
Projection: 1"
Half Round Rod: 11/16"
Length: Specify 4", 6", 9" or 12"
253
• Heavy duty, decorative bolt ideal where extra strength required
• Decorative 1-1/4" diameter knob fits well with any décor and designed to
facilitate bolt operation.
• Made from solid brass.
• Available in 8", 12", 18", 24", 30", 34", 36", 42", 48", 54", 60" and 72" lengths.
Bolts 18" and over are furnished with 3 guides. For B14, B15, B15A, B26 and
B26D finishes, maximum rod length is 24".
• Specify desired strike: Universal Strike (US) or Mortise Strike (MS).
• Meets design requirements of ANSI/BHMA A156.16.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
To Order: Specify finish, length and strike.
Dimensions:
Throw: 1-1/8"
Projection: 1-5/16"
Half Round Rod: 5/8"
Overall Width: 1-5/8"
Length: Specify 8", 12", 18", 24", 30",
34", 36", 42", 48", 54", 60" or 72"
353
• Heavy duty, decorative bolt ideal where extra strength required
• Swirled colonial 1-1/4" diameter knob designed to facilitate
bolt operation
• Made from solid brass
• Available in 8", 12", 18", 24", 30", 36", 48", and 72" lengths.
Bolts 18" and over are furnished with 3 guides. For B14, B15, B15A,
B26 and B26D finishes, maximum rod length is 24".
• Specify desired strike: Universal Strike (US) or Mortise Strike (MS)
• Meets design requirements of ANSI/BHMA A156.16
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D
D
E
U
N
I
T
N
O
C
DIS
To Order: Specify finish, length and strike.
E8
Dimensions:
Throw: 1-1/8"
Projection: 1-5/16"
Half Round Rod: 5/8"
Overall Width: 1-5/8"
Length: Specify 8", 12", 18", 24", 30",
36", 48", or 72"
Decorative Surface Bolts
354
• Heavy duty, decorative bolt ideal where extra strength required.
• Swirled colonial 1-1/4" diameter knob with decorative guides designed to
facilitate bolt operation.
• Made from solid brass.
• Available in 8", 12", 18", 24", 30", 36", 48", and 60" lengths.
Bolts 18" and over are furnished with 3 guides. For B14, B15, B15A, B26
and B26D finishes, maximum rod length is 24".
• Specify desired strike: Universal Strike (US) or Mortise Strike (MS).
• Meets design requirements of ANSI/BHMA A156.16.
• Finishes: B3, B4, B5, B10B, B14, B15, B15A, B26, B26D.
D
E
U
N
I
T
N
O
C
DIS
To Order: Specify finish, length and stike.
Dimensions:
Throw: 7/8"
Projection: 1-5/16"
Half Round Rod: 5/8"
Overall Width: 1-3/4"
Length: Specify 8", 12", 18", 24", 30", 36",
48", or 60"
E9
Dutch Door Bolts
054 and 55
• Practical, rugged, attractive bolt for application on dutch doors as well as
other areas.
• Chamfered rod end draws the two leaves of door tightly together.
• Sufficient tolerance provided in strike opening to allow for misalignment of
door leaves and also prevents binding of bolt.
• 054 features decorative 1" diameter knob designed to facilitate bolt operation.
• 55 features swirled colonial 1-1/4" diameter knob designed to facilitate bolt
operation.
• Made from solid brass.
• Packed with Standard Strike. Optional Mortise Strike (MS) for shelf door
application available. Optional Universal Strike (US) also available.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
To Order: Specify finish.
054
Dimensions:
Throw: 5/8"
Projection: 1-1/8"
Half Round Rod: 5/8"
Overall Width: 1-5/8"
Rod Length: 4-1/4"
Overall Length, including knob: 4-3/8"
55
Dimensions:
Throw: 5/8"
ED
Projection: 1-5/16"
NU
I
T
NRod: 5/8"
Half Round
COWidth: 1-9/16"
Overall
S
I
D Rod Length: 4-1/4"
Overall Length, including knob: 4-1/2"
56
• Dutch Door Quadrant features decorative design.
• Combines artistry, engineering and craftsmanship to provide the most
attractive and rugged dutch door quadrant available.
• Quadrant will not rattle. Assembled with heavy rivet and
spring washer for constant tension to hold quadrant in position.
• Non-handed.
• Made from cast brass.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
Projection: 1-1/4"
Base: 2-3/4" x 1-1/4"
Height: 4-1/2"
Width: 4-3/8"
E10
Security Door Bolts
87
• Security Door Bolt is the ultimate in strength, simplicity, and security.
• Solid brass bolt is permanently housed in a precision
designed extrusion of solid brass.
• Milled slot in bolt housing insures bolt remains locked or
unlocked in spite of vibration.
• Non-handed.
• Made from solid brass.
• Packed with universal, surface, and angle strikes, and recessed head screws.
• Finishes: B3, B4, B5, B10, B10B, B15, B15A, B26, B26D.
To Order: Specify finish.
D
E
U
N
I
T
N
O
C
S
I
D
Dimensions:
Throw: 5/8"
Projection: 15/32"
Bolt Diameter: 5/16"
Overall Width: 1-1/4"
Length: 2-1/4"
E11
Door Guards
481
• Chain Door Guard permits the door to be slightly opened to allow
viewing.
• Narrow chain holder maintains chain in stationary position when
door guard is not in use, eliminating marring of door and frame
caused by dangling chain.
• Welded twist link steel chain finished to match door plate and
chain holder.
• Meets design requirements of ANSI/BHMA A156.16.
• Made from wrought brass or burnished wrought steel.
• Packed with sheet metal screws.
• Finishes: B3, B4, B5, B10, B10B, B15, B26, B26D, F3, F5, F15.
Dimensions
Door Plate: 3-3/8" x 1-7/16"
Chain Holder: 3/4" x 1-15/16"
Chain Length: 4-3/4"
482
• Solid Bar Door Guard is for use on doors that are flush with frames.
• The solid bar, interlocking with the ball on the strike plate, permits the
door to be slightly opened to allow viewing.
• The hinged bar allows the door guard to be positioned 1800 away from
the door when not in use.
• Edge guard, furnished with cast brass door guards, minimizes the
chance for marring the door or frame.
• Strike plate is designed to prevent the solid bar from marring the inside
of the door when in use.
• Easy installation.
• Meets ANSI/BHMA A156.16.
• Made from cast brass or cast aluminum.
• Packed with sheet metal screws.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, A3, A5,
A26, A26D.
To Order: Specify finish.
E12
Dimensions of Cast Brass Door Guard
Strike Plate: 2-5/8" x 1-1/32"
Holder: 1-3/4" x 1-1/16"
Arm Length: 4-3/4"
Edge Guard: 1-1/8" x 1-1/32"
Dimensions of Cast Aluminum Door Guard
Strike Plate: 2-1/2" x 7/8"
Holder: 2-1/2" x 15/16"
Arm Length: 3-13/16"
Section F
Exterior Door Hardware
Lock Guards
LG1
• Units are non-handed and incorporate security frame pin to prevent
separation of the door and frame.
• Unit covers the latch bolt area of the door and lock, thereby providing
added protection from burglars, vandals or normal abuse.
• Ideal for use with mortise or cylindrical locks.
• Easy installation.
• Through bolted with carriage bolts and nuts.
• Available in a variety of materials, 13 gauge stainless steel, 12 gauge
steel and brass material.
• Finishes: Stainless Steel—US32D
Steel—US2G, USP, SP313 (Dark Bronze)
Brass—US4, US10
Dimensions:
11-1/2" Tall x 3" Wide
LG7
• Units are non-handed.
• Identical to LG1 without security frame pin.
• Unit covers the latch bolt area of the door and lock, thereby providing
added protection from burglars, vandals or normal abuse.
• Ideal for use with mortise or cylindrical locks.
• Easy installation.
• Through bolted with carriage bolts and nuts.
• Available in 13 gauge stainless steel.
• Finish: Stainless Steel—US32D
Dimensions:
11-1/2" Tall x 3" Wide
How to Order:
LG____ - ____
Model:
1
7
Finishes:
LG1
LG7
US2G, US4, US10, USP, US32D, SP313
US32D
F1
Lock Guards
LG10 thru LG12
LG10
• Ideally suited for use with rose or escutcheon 2-3/4" wide or less.
• For use with Type 86 Mortise and Type 161 Cylinder Locks (ANSI
156.13 Series 1000 and ANSI 156.2 Series 4000).
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating
the opening between door and frame at the latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel.
• Finishes: Stainless Steel—US32D
Steel—USP
Dimensions:
9-1/2" Tall x 2-1/2" Wide
LG11
• Designed for use on aluminum doors with latch-type locks
or doors equipped with electric strikes.
• Unit is Handed - Specify left or right hand when ordering.
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually
eliminating the opening between door and frame at
latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel.
• Finishes: Stainless Steel—US32D
Steel—SP313 (Dark Bronze)
Dimensions:
9-1/2" Tall x 3" Wide
LG12
• Narrow design unit for use on rose or escutcheon 3-1/2" or less.
• For use with Type 86 Mortise and Type 161 Cylinder Locks
(ANSI 156.13 Series 1000 and ANSI 156.2 Series 4000).
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating
the opening between door and frame at the latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel
• Finishes: Stainless Steel—US32D
Steel—USP
Dimensions:
9-1/2" Tall x 1-1/2" Wide
F2
Lock Guards
LG13 thru LG14
LG13
• Designed for use on all Type 161 Cylinder Locks
(ANSI 156.2 Series 2000) Monolock and Unilock.
• No exposed fasteners on face of unit.
• Unique design provides maximum security, virtually eliminating
the opening between door and frame at latch point.
• Available in 13 Gauge Stainless Steel or 12 Gauge Steel.
• Finishes: Stainless Steel—US32D
Steel—USP
Dimensions:
7" Tall x 1-1/2" Wide
LG14
•
•
•
•
•
•
Narrow design unit for use on rose or escutcheon 3-1/2" or less.
For use with Von Duprin 6211 electric strike.
No exposed fasteners on face of unit.
Unique design provides maximum security.
Available in 13 Gauge Stainless Steel
Finish: Stainless Steel—US32D
Dimensions:
9-1/2" Tall x 2-9/16" Wide
How to Order:
LG ____ - ____ - ____
Model:
10
11
12
13
14
Handing:
LG11 only (LH or RH)
Finishes:
LG10
LG11
LG12
LG13
LG14
US32D, USP
US32D, SP313
US32D, USP
US32D, USP
US32D
F3
Crash Stop
Extra Heavy Duty Crash Stop
CS115
• Specially designed for full-size exterior doors.
• Tear resistant, grey vinyl cover.
• Heavy duty compression spring assembled
to both ends of chain and end brackets.
• Packed with sheet metal screws.
• Cast Brass brackets with solid, welded steel chain.
• Meets ANSI/BHMA A156.16, L12231, (Grade 1).
• Finishes: US3, US4, US5, US10, US10B, US14,
US15, US15A, US26, US26D.
• Optional thru-door fastening; machine screws with brass
cap nuts and brass washers plated to the required finish.
Order separately 09-340. Specify finish.
Prod
No.
Lgth.
Recommended
Door Width
Bracket
Size
115-20
115-25
115-30
20-1/2"
25-1/2"
30-1/2"
30"
36"
42"
1-9/16" X 1-9/16"
1-9/16" X 1-9/16"
1-9/16" X 1-9/16"
How to Order:
CS115- ____ - ____
Size:
20
25
30
Finishes:
US3, US4, US5, US10, US10B, US14, US15, US15A, US26,
US26D, US10B.
Exterior Door Hardware
15 Crash Stop
D
E
U
N
I
T
N
O
C
DIS
• For storm and combination doors.
• Protects doors, hinges and glass from wind damage.
• Rugged compression spring absorbs shock.
• Made with heavy gauge wrought steel brackets and steel chain.
• Packed with sheet metal screws.
• 22-3/4" long bracket.
• 13/16" diameter spring.
• Finish: F2C.
F4
Exterior Door Hardware
Screen Door Pull
25
• Made from cast aluminum or epoxy-coated aluminum.
• Can also be used as a window lift, drawer or utility pull.
• Finishes: A3, A4, A5, A10, A14, A92, A-A (almond), A-W (white),
A-BLK (black).
Dimensions:
Overall Length: 4-7/8"
Mounting Hole Center-to-Center: 4-1/8"
Projection: 1-5/32"
Storm Door Latch
980
• For wood storm doors 7/8" to 1-1/8" thick.
• Reversible: fits right or left hand, inswinging or outswinging doors.
• Security lock feature operates from inside rose.
• Solid brass safety strike assures latching and is designed to
compensate for air pressure build-up between doors.
• Made from wrought brass.
• Finishes: B3, B5, B10B, B15, B15A, B26, B26D.
Dimensions:
Backset: 1-3/4"
Rose Diameter: 1-7/8"
Knob Diameter: 1-3/4"
Knob Projection: 2"
Lever Length: 1-3/4"
Lever Projection: 1-7/8"
Non-Electric Door Chime
780
• Polished wrought brass front plate, inset with satin black plastic
push plate.
• Chime case in ivory plastic.
• Ideal for interior apartment doors, condominiums and hotel/motels.
• Combines low initial cost with fast, economical installation.
• Unique placement of name and apartment number cards conceals
mounting screws.
• Optical glass viewer permits screening of callers and is shutter
controlled to insure one way vision only.
• Two-tone, mellow and resonant chime.
• Requires only one hole, 1" in diameter, through door.
• Fits 1-1/4" through 1-3/4" doors. Contact factory for use on other
thickness doors.
• Packed with template and installation instructions, screws, name and
number cards.
• Furnished with 700 viewer.
D
E
U
N
I
T
N
O
C
DIS
Prod
No.
Front Plate
Width Height Proj.
Chime Case
Width Height Proj.
780
2-1/2" 4-9/16"
2-3/4" 6-1/16"
1"
2"
Finishes
Front plate
Chime Case
B3, B26D
Ivory Plastic
F5
Viewers
One-Way Viewer
U696
• 150° Angle of View.
• For doors 1-3/8" to 2-1/16" thick.
• Secure, tamper-resistant.
• Solid brass body; glass lens.
• Simple installation — only a 1/2" hole required.
• Suggested installation height: 60" from floor.
• Trim washer available, 3/4" x .032" thick.
• UL Listed for use on fire door assemblies rated at 90 minutes.
• Conforms to ANSI/BHMA L23172 and L23222.
• Finishes: B4, B26D.
One-Way Viewer
U697
D
E
U
N
I
T
N
O
C
DIS
• 150° Angle of View.
• For doors 2-18" to 2-5/8" thick.
• Secure, tamper-resistant.
• Solid brass body; glass lens.
• Simple installation — only a 1/2" hole required.
• Suggested installation height: 60" from floor.
• Trim washer available, 3/4" x .032" thick.
• UL Listed for use on fire door assemblies rated at 90 minutes.
• Conforms to ANSI/BHMA A156.16 L23172 and L23222.
• Finishes: B4, B26D.
One-Way Wide Angle Viewer
698
U698
• 190° Angle of View.
• Lens projects 1/4" from face of door.
• 4 optical glass lenses.
• For doors 1-3/8" to 2-1/8" thick.
• Solid brass body and barrel.
• Simple installation — only a 9/16" hole required.
• Suggested installation height: 60" from floor.
• U698 is UL Listed for use on fire door assemblies rated at 90
minutes.
• Conforms to ANSI/BHMA A156.16 L23172 and L23222.
• Finishes: B3, B26D.
F6
Viewers
One-Way Viewer
700
U700
•
•
•
•
•
•
•
•
•
120° Angle of View.
For doors 1-3/8" to 2-1/16" thick.
Secure, tamper-resistant.
Solid brass body; glass lens.
Simple installation—only a 1/2" hole required.
Suggested installation height: 60" from floor.
Trim washer available, 3/4" x .032" thick.
U700 is UL Listed for use on fire door assemblies rated at 90 minutes.
Conforms to ANSI/BHMA A156.16 L23173 (700, U700) and L23222
(U700).
• Finishes: B4, B26D.
One-Way Viewer
701
U701
•
•
•
•
•
•
•
•
120° Angle of View.
For doors 2-1/8" to 2-5/8" thick.
Secure, tamper-resistant.
Solid brass body; glass lens.
Simple installation—only a 1/2" hole required.
Suggested installation height: 60" from floor.
Trim washer available, 3/4" x .032" thick.
U701 is UL Listed for use on fire door assemblies rated at 90
minutes.
• Conforms to ANSI/BHMA A156.16 L23173 (701, U701) and
L23222 (U701).
• 701 Finishes: B4, B10B, B15, B15A, B26, B26D.
• U701 Finishes: B4, B26D.
F7
Door Knockers
Door Knocker with Number Plate, Optional Viewer
763 Knocker Only
U763 x U700 Knocker with Viewer
D
E
U
N
I
T
N
O
C
DIS
• Knocker made from solid brass.
• Factory-engraved number plates available. White numerals and/or
letters, mazimum of 7, engraved on mahogany-grained plastic plate.
When ordering, specify “E” prefix and engraving requirements.
• Conforms to ANSI/BHMA A156.16 L23151.
• Packed with sheet metal screws.
• Knocker Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
• Viewers supplied in B4 or B26D.
Knocker Dimensions:
Length: 4"
Width: 2-3/16"
Projection: 9/16"
Mounting Hole Center-to-Center: 3-7/32"
Door Knocker with Number Plate/Card Holder, Optional Viewer
764 Knocker Only
U764 x U700 Knocker with Viewer
• Knocker made from solid brass.
• Factory-engraved number plates available. White numerals and/or
letters, mazimum of 7, engraved on mahogany-grained plastic plate.
When ordering, specify “E” prefix and engraving requirements.
• Conforms to ANSI/BHMA A156.16 L23151.
• Packed with sheet metal screws.
• Knocker Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
• Viewers supplied in B4 or B26D.
Knocker Dimensions:
Length: 4-15/16"
Width: 2-3/16"
Projection: 9/16"
Mounting Hole Center-to-Center: 3-7/32"
Door Knocker with U696/U698/U700 Viewer
771 Knocker Only
U771 x U696 Knocker with Viewer
U771 x U698 Knocker with Viewer
U771 x U700 Knocker with Viewer
D
E
U
N
I
T
N
O
C
DIS
• Knocker made from solid brass.
• Mounting screws concealed. Packed with sheet metal screws.
• Conforms to ANSI/BHMA A156.16 L23151.
• Knocker Finishes: B3, B5, B10, B26, B26D.
• U696 and U700 Viewers supplied in B4 or B26D.
U698 Viewer supplied in B3 or B26D.
F8
Knocker Dimensions:
Length: 3-1/8"
Width: 2-1/8"
Projection: 1/2"
Mounting Hole Center-to-Center: 2-1/4"
Door Knockers
Door Knocker with Number Plate, Card Holder and Optional U698/U700/U701 Viewer
774 Knocker Only
U774 x U698 Knocker with Viewer
U774 x U700 Knocker with Viewer
U774 x U701 Knocker with Viewer
D
E
U
N
I
T
N
O
C
DIS
• Knocker made from solid brass.
• Factory-engraved number plates available. White numerals and/or
letters, mazimum of 7, engraved on mahogany-grained plastic plate.
When ordering, specify “E” prefix and engraving requirements.
• Mounting screws concealed. Packed with sheet metal screws.
• Conforms to ANSI/BHMA A156.16 L23151.
• Knocker Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26D.
• U698 Viewer supplied in B3 or B26D.
U700 and U701 Viewers supplied in B4 or B26D.
Knocker Dimensions:
Length: 4-3/16"
Width: 2-3/16"
Projection: 1/2"
Mounting Hole Center-to-Center: 2-1/4"
Door Knocker with Optional Viewers
02-3100 Knocker Only
02-31001 Knocker with 700 Viewer
02-31001U Knocker with U700 Viewer
02-31002 Knocker with 701 Viewer
D
E
U
N
I
T
N
O
C
DIS
• Knocker made from forged brass.
• Knocker Finishes: 605, 606, 609, 612, 613, 618, 619, 620, 625, 626.
• Viewers supplied in B4 or B26D.
Knocker Dimensions:
Length: 7-1/16"
Width: 2-15/16"
Projection: 7/8"
Mounting Hole Center-to-Center: 4-15/16"
Door Knocker with Optional Viewers
02-3101 Knocker Only
02-31011U Knocker with U700 Viewer
02-31012 Knocker with 701 Viewer
02-31012U Knocker with U701 Viewer
D
E
U
N
I
T
N
O
C
S
I
D
• Knocker made from forged brass.
• Knocker Finishes: 605, 606, 609, 612, 613, 618, 619, 620, 625, 626.
• Viewers supplied in B4 or B26D.
Knocker Dimensions:
Length: 6-11/16"
Width: 1-7/8"
Projection: 13/16"
Mounting Hole Center-to-Center: 5-7/8"
F9
Door Knockers
Door Knocker with Optional Viewers
02-3102 Knocker Only
02-31021 Knocker with 700 Viewer
02-31021U Knocker with U700 Viewer
02-31022 Knocker with 701 Viewer
02-31022U Knocker with U701 Viewer
D
E
U
N
I
T
N
O
C
DIS
• Knocker made from forged brass.
• Knocker Finishes: 605, 606, 609, 612, 613, 618, 619, 620, 625, 626.
• Viewers supplied in B4 or B26D.
Knocker Dimensions:
Length: 6-7/16"
Width: 2-15/16"
Projection: 15/16"
Mounting Hole Center-to-Center: 4-1/8"
Door Knocker with Optional Viewer, Magnetic Mounting
02-3107 Knocker Only
02-31072 Knocker with 701 Viewer
02-3107MAG Magnetic Knocker
• Knocker made from forged brass.
• 2-3107 MAG features magnetic mounting on metal doors.
• Knocker Finishes, excluding magnetic: 605, 606, 609, 612, 613,
618, 619, 620, 625, 626.
• 02-3107MAG Finishes: 505, 605.
• Viewers supplied in B4 or B26D.
Knocker Dimensions:
Length: 8-1/2"
Width: 4-1/8"
Projection: 1"
Mounting Hole Center-to-Center: 5"
Door Knocker
02-3115
• Knocker made from forged brass.
• Knocker Finishes: 605, 606, 609, 612, 613, 618, 619, 620, 625, 626.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
Length: 7-3/4"
Width: 2"
Projection: 2-7/8"
Mounting Hole Center-to-Center: 5"
F10
Door Knockers
Door Knocker with Optional Viewers
02-3122 Knocker Only
02-31221 Knocker with 700 Viewer
02-31221U Knocker with U700 Viewer
02-31222 Knocker with 701 Viewer
02-31222U Knocker with U701 Viewer
• Knocker made from wrought brass.
• Knocker Finishes: 605, 606, 609, 612, 613, 618, 619, 620, 625, 626.
• Viewers supplied in B4 or B26D.
Dimensions:
Length: 4"
Width: 2-3/16"
Projection: 9/16"
Mounting Hole Center-to-Center: 3-7/32"
Door Knocker with Optional Viewers
02-3125 Knocker Only
02-31251 Knocker with 700 Viewer
02-31251U Knocker with U700 Viewer
02-31252 Knocker with 701 Viewer
02-31252U Knocker with U701 Viewer
• Knocker made from forged brass.
• Knocker Finishes: 605, 606, 609, 612, 613, 618, 619, 620, 625, 626.
• 02-3125 and 02-31252 also available in 505.
• Viewers supplied in B4 or B26D.
Dimensions:
Length: 5-15/16"
Width: 3"
Projection: 1-1/16"
Mounting Hole Center-to-Center: 3-15/16"
F11
House Numbers
Century House Numbers
02-30_0
•
•
•
•
4" High.
Made from cast brass.
Brass screws included.
Finish: 605.
D
E
U
N
I
T
N
O
C
DIS
Model
House Number
02-3000
#0
02-3010
02-3020
02-3030
02-3040
02-3050
02-3060
02-3070
02-3080
02-3090
#1
#2
#3
#4
#5
#6
#7
#8
#9
Century House Numbers
02-30_1
D
E
U
N
I
T
N
O
C
DIS
• 6" High.
• Made from forged brass.
• Brass screws included.
• Finish: 605.
Model
House Number
02-3001
02-3011
02-3021
02-3031
02-3041
02-3051
02-3061
02-3071
02-3081
02-3091
#0
#1
#2
#3
#4
#5
#6
#7
#8
#9
Heritage House Number
02-30_3
• 2-3/4" High.
• Colonial styling.
• Made from cast brass.
• Fits limited space; often
used for apartments and hotel rooms.
• Conforms to ANSI/BHMA A156.16 L13181.
• Brass brads included.
• Finish: 605.
D
E
U
N
I
T
N
O
C
DIS
F12
Model
02-3003
02-3013
02-3023
02-3033
02-3043
02-3053
02-3063
02-3073
02-3083
02-3093
House Number
#0
#1
#2
#3
#4
#5
#6
#7
#8
#9
House Numbers
Traditional House Numbers
02-30_4
• 4" High.
• Popular traditional styling for easy readability.
• Made from solid wrought brass.
• Conforms to ANSI/BHMA A156.16 L13181.
• Brass brads included.
• Finishes: 605, 609, 619, 620, 626.
D
E
U
N
I
T
N
O
C
DIS
Model
02-3004
02-3014
02-3024
02-3034
02-3044
02-3054
02-3064
02-3074
02-3084
02-3094
House Number
#0
#1
#2
#3
#4
#5
#6
#7
#8
#9
Contemporary House Numbers
02-30_5
• 5" High.
• Bold, thick design is easy to see from a distance.
• Made from cast brass.
• Mounting screws included.
• Finishes: 505, 605, 613, 619, 620, 625.
D
E
U
N
I
T
N
O
C
S
I
D
Model
02-3005
02-3015
02-3025
02-3035
02-3045
02-3055
02-3065
02-3075
02-3085
02-3095
House Number
#0
#1
#2
#3
#4
#5
#6
#7
#8
#9
Hammered Aluminum Traditional House Numbers
466
D
E
U
N
I
T
N
O
C
DIS
• 4-1/2" High.
• Conforms to ANSI/BHMA A156.16 L43191.
• Brads included.
• Black, electroplated on aluminum.
• Finish: A19.
Model
466 NO.0
466 NO.1
466 NO.2
466 NO.3
466 NO.4
466 NO.5
466 NO.6
466 NO.7
466 NO.8
466 NO.9
House Number
#0
#1
#2
#3
#4
#5
#6
#7
#8
#9
F13
Letter Box Plates - Weather-Tite®
Weather-Tite® Letter Box Plates
• Weather-Tite construction featuring interlocking flap and frame
gives added protection from weather.
• 620 Series Models feature spring loaded front plate features bronze
spring to insure tightly closed position. Can be installed in vertical
position. 618 and 619 models are gravity operated only.
• Rugged construction. Made of heavy gauge wrought brass, bronze
or aluminum.
• Template for door cut-out packed with all letter box plates.
• Sex bolts optional.
Letter Box Plate with Standard (Open) Back Plate
618
• Gravity operated front plate.
• Finish: A63.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Overall Size: 10" x 3"
Plate Opening: 7-1/2" x 2"
Letter Box Plate with Covered Back Plate
619
• Gravity operated front plate.
• Finish: A63.
D
E
U
TIN
N
O
C
S
DI
Dimensions:
Overall Size: 10" x 3"
Plate Opening: 7-1/2" x 2"
Magazine Size Letter Box Plate with
Standard (Open) Back Plate
620
• Spring-loaded front plate.
• Finishes: B-505, B3, B4, B5, B10, B10B(B613), B14, B15,
B15A(B-620), B26(B-625), B26D, PA28.
Dimensions:
Overall Size: 13" x 3-9/16"
Plate Opening: 11" x 2"
Magazine Size Letter Box Plate with
Covered Back Plate
621
D
E
U
TIN
N
CO
S
I
D
• Spring-loaded front plate.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, PA28.
F14
Dimensions:
Overall Size: 13" x 3-9/16"
Plate Opening: 11" x 2"
Letter Box Plates - Weather-Tite®
Weather-Tite® Letter Box Plates
• Weather-Tite construction featuring interlocking flap and frame
gives added protection from weather.
• 620 Series Models feature spring loaded front plate features bronze
spring to insure tightly closed position. Can be installed in vertical
position. 618 and 619 models are gravity operated only.
• Rugged construction. Made of heavy gauge wrought brass, bronze
or aluminum.
• Template for door cut-out packed with all letter box plates.
• Sex bolts optional.
Magazine Size Letter Box Plate with
Hood and Covered Back Plate
622
D
E
U
N
I
T
N
O
C
DIS
• Spring-loaded front plate.
• Finish: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
Dimensions:
Overall Size: 13" x 3-9/16"
Plate Opening: 11" x 2"
Hood Projection: 1-5/8"
Letter Box Plate with Standard (Open) Back Plate
623
D
E
U
TIN
N
O
C
S
DI
• Spring-loaded front plate.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, PA28.
Dimensions:
Overall Size: 10" x 3"
Plate Opening: 7-1/2" x 2"
Letter Box Plate with Covered Back Plate
624
D
E
U
N
I
T
N
O
C
DIS
• Spring-loaded front plate.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, PA28.
Dimensions:
Overall Size: 10" x 3"
Plate Opening: 7-1/2" x 2"
Letter Box Plate with Hood and Covered Back Plate
625
D
E
U
TIN
N
CO
S
I
D
• Spring-loaded front plate.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26D, PA28.
Dimensions:
Overall Size: 10" x 3"
Plate Opening: 7-1/2" x 2"
Hood Projection: 1-5/8"
F15
Letter Box Plates - Weather-Tite®
Weather-Tite® Letter Box Plates
• Weather-Tite construction featuring interlocking flap and frame
gives added protection from weather.
• 620 Series Models feature spring loaded front plate features bronze
spring to insure tightly closed position. Can be installed in vertical
position. 618 and 619 models are gravity operated only.
• Rugged construction. Made of heavy gauge wrought brass, bronze
or aluminum.
• Template for door cut-out packed with all letter box plates
• Sex bolts optional.
Letter Box Plate with Standard (Open) Back Plate
626
D
E
U
TIN
N
CO
S
I
D
• Spring-loaded front plate.
• Finishes: B-505, B3, B4, B5, B10, B10B(B-613), B14,
B-15(B-619), B15A(B-620), B26(B-625), B26D, PA28.
Dimensions:
Overall Size: 8-3/4" x 2-7/8"
Plate Opening: 7" x 1-7/8"
Letter Box Plate with Covered Back Plate
627
D
E
U
TIN
N
CO
S
I
D
• Spring-loaded front plate.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
Dimensions:
Overall Size: 8-3/4" x 2-7/8"
Plate Opening: 7" x 1-7/8"
Sleeves for use with Letter Box Plates
600 Sleeve for use with 626 and 627 Letter Box Plates
601 Sleeve for use with 620, 621 and 622 Letter Box Plates
602 Sleeve for use with 618, 619, 623 and 624 Letter Box Plates
• Made of stainless steel.
• For 1-3/4" hollow core doors.
F16
Letter Box Plates - Magnetract™
Magnetract™ Magazine Size Letter Box Plates
650 Magnetic Front Plate, Open Back Plate
651 Magnetic Front Plate, Covered Back Plate
652 Hooded Magnetic Front Plate, Covered Back Plate
• Magnetic inlays on plate and flap augment gravity to hold flap
closed to assure weather-tight fit and rattle-free installation.
• Rugged construction. Massive extrusions for strength and
resistance to weather, coupled with exclusive interlocked hinge
design that redirects forces and holds flap securely in place.
• Ideal for exterior doors. Projection of lip assures easy grasp,
even with gloves or mittens.
• Concealed pin permanently locks flap in plate. Tamper-resistance when used in conjunction with sex bolts.
• Template for door cut-out packed with all letter box plates.
• 650 and 651 packed with sheet metal screws; sex bolts
optional. 652 packed with sex bolts only.
• U.S. Patent 3,389,854.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
Overall Size: 12-1/2" x 3-1/4"
Plate Opening: 11" x 1-7/8"
Sleeves for use with Letter Box Plates
D
E
U
N
I
T
N
O
C
DIS
603 Sleeve for use with 650, 651, and 652
• Made of stainless steel.
• For 1-3/4" hollow core doors.
• Flanges on sleeve prevent buckling and eliminates sharp edges.
• Shims provided with all sleeves assure even mounting and tight
weather seal.
• Sex bolts for thru door application and gaskets for glass doors
available at extra charge.
F17
Door Closer
927 Pneumatic Door Closer
•
•
•
•
•
F18
For light interior doors or exterior storm doors.
For use on wood or metal doors.
Three-position spring hub for adjustable latching power.
Adjustable closing speed.
Factory lubricated.
D
E
U
N
I
T
N
O
C
DIS
Section G
Latches and Catches
Roller Latches
RL30
• Actuation is simple, closing of the door causes the
roller to fall in the depression of the strike, thereby
holding the door closed.
• The projection of the roller is easily adjusted using
adjusting screws on the face of the unit.
• Maximum projection of the roller is 3/8" allowing for
variance in the door clearance.
• Nylon Roller Standard.
• Forged Brass Construction.
• Meets ANSI/BHMA A156.16, E19091.
• Finishes: US3, US4, US10, US10B, US26, US26D.
• Optional Roller—F— Nylon covered brass roller.
• Optional Strike—A—ASA
Dimensions:
Body: 1" Wide x 3-3/8" Long x 1-11/16" Deep
Strike: 1-11/16" Wide x 2-1/4" Long x 5/32" Thick
Optional ASA Strike: STK726 (not shown): 1-1/4" wide x 4-7/8"
long x 3/32" thick
RL32
• Actuation is simple, closing of the door causes the
roller to fall in the depression of the strike, thereby
holding the door closed.
• The projection of the roller is easily adjusted by turning
knurled knob on back of latch.
• Maximum projection of the roller is 1/2" allowing for
variance in the door clearance.
• Fits heavy-duty cylindrical lock cutout.
• Nylon Roller Standard.
• Non-handed.
• Brass or Stainless Steel Construction.
• Meets ANSI/BHMA A156.16, E19101.
• Finishes: US3, US4, US10, US10B, US32, US32D.
• Optional Roller—F— Nylon covered brass roller.
• Optional Strike—A—ASA.
Dimensions:
Body: 1-1/8" Wide x 2-1/4" Long x 2-1/4" Deep
Strike: 1-1/8" Wide x 2-3/4" Long x 3/32" Thick
Optional ASA Strike: STK726 (not shown): 1-1/4" wide x 4-7/8"
long x 3/32" thick
How to Order:
RL ____ ____ ____ - ____
Model:
30
32
Roller Type:
Blank
Standard Nylon Roller
F
Nylon Coated Brass Roller
Strike Type:
Blank
Standard Strike
A
ASA Strike
Finishes:
RL30
RL32
US3, US4, US10, US10B, US26, US26D
US3, US4, US10, US10B, US32, US32D
G1
Roller Latches
RL36
• Actuation is simple, closing of the door causes the
roller to fall in the depression of the strike, thereby
holding the door closed.
• The projection of the roller is easily adjusted by turning
slotted screw on back of latch.
• Maximum projection of the roller is 5/16" allowing for
variance in the door clearance.
• Fits cylindrical lock cutout.
• Nylon Roller.
• Non-handed.
• Stainless Steel Construction.
• Meets ANSI/BHMA A156.16, L17082.
• Finish: US32D
• Optional Strike–A—ASA.
Dimensions:
Body: 1" Wide x 2-1/4" Long x 2" Deep
Strike: 1-1/8" Wide x 2-3/4" Long x 3/32" Thick
Optional ASA Strike: STK726 (not shown): 1-1/4" wide x 4-7/8"
long x 3/32" thick
RL38
• Actuation is simple, closing of the door causes the
roller to fall in the depression of the strike, thereby
holding the door closed.
• The projection of the roller is easily adjusted by turning
slotted screw.
• Maximum projection of the roller is 3/8" allowing for
variance in the door clearance.
• Nylon Roller.
• Non-handed.
• Stainless Steel Construction.
• Meets ANSI/BHMA A156.16, L27092.
• Finish: US32D
Dimensions:
Body: 2" Tall x 1-3/8" Wide x 7/8" Deep
Strike: 2-1/8" Tall x 1" Wide x 3/8" Deep
RL1152
• Combination of RL30 Roller Latch and Angle Stop.
• Actuation is simple, closing of the door causes the
roller to fall in the depression of the strike, thereby
holding the door closed.
• The projection of the roller is easily adjustable using
adjusting screws on the face of the unit.
• Maximum projection of the roller is 3/8" allowing for
variance in the door clearance.
• Nylon Roller Standard.
• Forged Brass Construction.
• Finishes: US3, US4, US10, US10B, US26 and US26D.
Dimensions:
Body: 4-1/2" Tall x 1-1/2" Wide x 1-3/4" Deep with 3/4" Angle
Strike: 2-1/4" Tall x 1-1/8" Wide x 5/32" Thick
How to Order:
RL ____ ____ - ____
Model:
36, 38 or 1152
Strike Type: (RL36 only)
Blank
Standard Strike
A
ASA Strike
Finishes:
RL36, RL38 US32D
RL1152
US3, US4, US10, US10B, US26, US26D
G2
Optional Strike
3/32"
1-11/16"
STK685
A
• Custom make strike for doors that swing both directions.
For use with roller latches.
• Constructed of 3/32" brass.
• Dimple of strike centered on strike.
• Specify frame depth - A.
• Finishes: US3, US4, US10, US10B, US26, US26D.
B
5/16"
A
A
R
1/8"
1-5/32"
2-1/4"
STK685L
• Custom make strike for doors that swing both directions.
For use with roller latches.
• Constructed of 3/32" brass.
• Dimple of strike is variable. Please specify location of
dimple from edge of frame - B.
• Specify frame depth - A.
• Finishes: US3, US4, US10, US10B, US26, US26D.
B
A
How to Order:
STK ____ - ____ - ____ - ____
Model:
685
685L
Finishes:
US3, US4, US10, US10B, US26, US26D
Frame Depth:
A
Dimple Location:
B (685L only)
G3
Angle Stops
AS895
•
•
•
•
Surface applied stop for single doors.
Large rubber bumper to ensure quiet operation.
Constructed of 1/8" Brass Angle.
Finishes: US3, US4, US10, US10B, US26, US26D.
Dimensions:
1-1/2" Wide x 1" Angle x 2-1/2" Long
AS18
• Surface applied stop for single and double doors.
• Includes SR64 door silencers to ensure quiet operation.
SR64 silencers are replaceable.
• Constructed of 3/16" Brass Angle.
• Finishes: US3, US4, US10, US10B, US26, US26D.
Dimensions:
1-1/2" Wide x 3/4" Angle x 2-1/2" Long
How to Order:
AS ____ - ____
Model:
18
895
Finishes:
US3, US4, US10, US10B, US26, US26D
G4
Ball Catches
CL21
• Four-way catch with hexagon stud.
• Ideal for holding medium duty doors.
• The strike slides between two stainless steel balls that are under
spring tension. As the strike engages, the door is held tightly shut.
• Strike can enter body from any direction.
• Spring tension is easily adjusted to suit field conditions.
• Body can be surface applied or mortised.
• Brass construction.
• Meets ANSI/BHMA A156.9.
• Finish: US26D.
Dimensions:
Body: 3" Tall x 3/4" Wide x 3/4" Deep
Strike: 1-1/2" Tall x 3/4" Wide Hex
CL21A
• Four-way catch with plate type strike.
• Ideal for closet doors, access doors, hinged openings
and numerous other applications.
• The strike slides between two stainless steel balls that are under
spring tension. As the strike engages, the door is held tightly shut.
• Strike can enter body from any direction.
• Spring tension is easily adjusted to suit field conditions.
• Body can be surface applied or mortised.
• Brass construction.
• Meets ANSI/BHMA A156.9, B13292.
• Finishes: US3, US4, US10, US26, US26D.
Dimensions:
Body: 3" Tall x 3/4" Wide x 3/4" Deep
Strike: 1-3/4" Tall x 7/16" Wide x 7/8" Deep
CL22
• Three-way catch with plate type strike.
• Ideal for smaller cabinet doors or panels.
• The strike slides between two stainless steel balls that are under
spring tension. As the strike engages, the door is held tightly shut.
• Strike can enter body from either side or front.
• Spring tension is easily adjusted to suit field conditions.
• Body can be surface applied or mortised.
• Brass construction.
• Meets ANSI/BHMA 156.9, B13302.
• Finishes US3, US4, US10, US26, US26D.
Dimensions:
Body: 2-3/16" Tall x 1/2" Wide x 1/2" Deep
Strike: 1-3/8" Tall x 3/8" Wide x 5/8" Deep
How to Order:
CL ____ - ____
Model:
21
21A
22
Finishes:
CL21
US26D
CL21A, CL22 US3, US4, US10, US26, US26D
G5
Invisible Latches
CL11
• Invisible latch is ideal for installations where no visible
latch is desired.
• Unit can be installed at the top, bottom or side of the door.
• Can be mortised into the stop or surface mounted to the stop.
• Recommended for use on small panels, cabinet doors or light
weight closet doors.
• Operation is simple, latching is accomplished by a slight push.
To unlatch the door, a harder push releases the door and pushes
the door out.
• Brass and plastic construction.
• Meets ANSI/BHMA 156.9, B03272.
• Finishes: US3, US4, US10, US26D.
Dimensions:
Body: 1-7/8" Tall x 1-1/4" Wide x 7/16" Thick
Strike: 1-5/16" Tall x 9/16" Wide x 9/16" High
CL12
• Invisible latch is ideal for installations where no visible
latch is desired.
• Unit can be installed at the top, bottom or side of the door.
• Can be mortised into the stop or surface mounted to the stop.
• Recommended for use on larger panels or regular size doors.
• Operation is simple, latching is accomplished by a slight push.
To unlatch the door, a harder push releases the door and pushes
the door out.
• Brass and plastic construction.
• Meets ANSI/BHMA A156.9, B03272.
• Finishes: US3, US4, US10, US26D.
Dimensions:
Body: 2-1/4" Tall x 1-1/4" Wide x 9/16" Thick
Strike: 1-13/16" Tall x 5/8" Wide x 9/16" High
CL14 Auxiliary Pusher
• Aid in the operation of the CL11 and CL12 where hinges or
surrounding conditions prevent smooth operation of doors.
• Provides 1-1/16" throw.
• Nylon pusher.
• Brass construction.
• Meets ANSI/BHMA A156.9, B13282.
• Finishes: US3, US4, US10, US26D.
Dimensions:
Body: 2-15/16" Long x 1-11/16" Wide x 5/8" High
How to Order:
CL ____ - ____
Model:
11
12
14
Finishes:
US3, US4, US10, US26D
G6
Magnetic Catches
323
• Triple pole.
• Self-aligning magnet insures maximum pull.
• Case design allows easy magnet adjustment on cabinet or small.
door applications.
• Aluminum case.
• Packed with sheet metal screws.
• Conforms to ANSI/BHMA A156.9.
• Finishes: A3, A5, A92.
D
E
U
IN
T
N
O
C
S
DI
Dimensions:
Case: 2-1/16" Long x 1-5/32" Deep x 7/8" Thick
Load Capacity: 6 lbs.
324
• Double pole.
• High impact plastic case is tan colored to blend with wood.
• Easy to adjust.
• Packed with sheet metal screws.
• Conforms to ANSI/BHMA A156.9 B03141.
• Finish: P69.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
Case: 1-3/4" Long x 9/16" Deep x 1/2" Thick
Load Capacity: 5 lbs.
325
• Double pole.
• Self aligning magnet insures maximum pull.
• Case design allows easy magnet adjustment on cabinet or small
door applications.
• Aluminum case.
• Packed with sheet metal screws.
• Conforms to ANSI/BHMA A156.9.
• Finishes: A3, A5, A92.
Dimensions:
Case: 2-1/16" Long x 1-1/8" Deep x 5/8" Thick
Load Capacity: 5 lbs.
G7
Magnetic Catches
326 Mighty-Mite® Heavy Duty Magnetic Catch
• Dual double pole.
• Self-aligning magnets insure maximum pull.
• Can be surface mounted or mortised.
• Aluminum case.
• Packed with sheet metal screws, 2 short strikes and 1 long strike.
• Conforms to ANSI/BHMA A156.9 B43161.
• Finishes: A3, A5, A92.
Dimensions:
Case: 3-1/8" Long x 1" Deep x 9/16" Thick
Load Capacity: 9 lbs.
327 Super-Mite® Heavy Duty Magnetic Catch
• Dual triple pole.
• Self-aligning magnets insure maximum pull.
• Can be surface mounted or mortised.
• Aluminum case.
• Packed with sheet metal screws, 2 short strikes and 1 long strike.
• Conforms to ANSI/BHMA A156.9 B43161.
• Finishes: A3, A5, A92.
Dimensions:
Case: 3-1/8" Long x 1" Deep x 3/4" Thick
Load Capacity: 14 lbs.
G8
Roller Catches
330 Double Roller Catch
• Independent rollers allow positive action and self-alignment.
• Cushioned rollers absorb shock and noise, hold door away from
cabinet.
• Surface application allows for easy adjustment.
• Made from wrought steel.
• Packed with screws and brads.
• Conforms to ANSI/BHMA A156.9 B83071.
• Finishes: F2C, F69.
Dimensions:
Case: 1-1/4" x 11/16"
Strike: 1-1/4" x 3/8"
335
• Smooth, positive latching action insured by powerful conical spring.
• Durable nylon roller insures quiet operation.
• Adjustable tension. Adjustments can be varied from 4 to 17 lbs. of
holding power making possible a wide range of door performance.
• Easily installed on thin doors.
• Full lip style strike designed for simplified mortising.
• Made from wrought brass or wrought steel.
• Packed with sheet metal screws.
• Conforms to ANSI/BHMA A156.16 L27081 for brass and L87081 for
steel.
• Finishes: B3, B4, B5, B10, B10B, B15, B15A, B19, B26, B26D, F3,
F5, F14.
Dimensions:
Face Plate: 2-1/4" x 7/8"
Bore: 13/16" x 1-3/4"
Strike: 2-1/4" x 1-5/8" Lip 1-13/16" to center
336
• Smooth, positive latching action insured by powerful conical spring.
• Durable nylon roller insures quiet operation.
• Adjustable tension. Adjustments can be varied from 4 to 17 lbs. of
holding power making possible a wide range of door performance.
• Easily installed on thin doors.
• Standard box type strike designed for neat appearance.
• Made from wrought brass or wrought steel.
• Packed with sheet metal screws.
• Conforms to ANSI/BHMA A156.16 L27081 for brass and L87801 for
steel.
• Finishes: B3, B4, B5, B10, B10B, B15, B15A, B19, B26, B26D, F3,
F10, F14.
Dimensions:
Face Plate: 2-1/4" x 7/8"
Bore: 13/16" x 1-3/4"
Strike: 2-1/4" x 7/8" Lip 1-1/8" to center
G9
Roller Catches
338
• Rubber roller provides quiet operation.
• Surface applied; requires no mortising or boring.
• Case design allows easy adjustment.
• Made from wrought steel.
• Packed with screws and brads.
• Conforms to ANSI/BHMA A156.9 B83112.
• Finishes: F3, F10, F14.
D
E
U
IN
T
N
O
C
S
DI
Dimensions:
Case: 2" x 1-1/16"
Strike: 1-3/4" x 3/4"
G10
Ball Catches
345 Adjustable Ball Catch
• Ideal for cabinets and small interior doors.
• Free rolling ball insures smooth, positive and trouble-free action.
• Adjustable threaded barrel compensates for various door
clearances.
• Adjustable spring tension.
• Made from wrought brass.
• Conforms to ANSI/BHMA A156.9 B23013.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
Face Plate: 1-1/2" x 3/4"
Bore: 9/16" x 1"
Strike: 1-1/2" x 25/32". Lip 13/32" to center
346 Dual Adjustable Ball Catch
• For catch in jamb installations.
• Dual adjustment for door clearance and holding strength.
• Narrow strike is designed for use where strike is mounted in door.
• Free rolling ball insures smooth, positive and trouble-free action.
• Adjustable threaded barrel compensates for various door
clearances.
• Adjustable spring tension.
• Made from wrought brass.
• Conforms to ANSI/BHMA A156.9 B23013.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
Face Plate: 2-1/8" x 1"
Bore: 7/8" x 1-3/8"
Strike: 2-1/8" x 1-1/16". Lip 9/16" to center
347 Dual Adjustable Ball Catch
• For catch in door installations.
• Dual adjustment for door clearance and holding strength.
• Lip strike is designed for use where strike is mounted in jamb.
• Free rolling ball insures smooth, positive and trouble-free action.
• Adjustable threaded barrel compensates for various door
clearances.
• Adjustable spring tension.
• Made from wrought brass.
• Conforms to ANSI/BHMA A156.9 B23013.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
Face Plate: 2-1/8" x 1"
Bore: 7/8" x 1-3/8"
Strike: 2-1/8" x 1-3/8". Lip 7/8" to center
G11
Ball Catches
348 Ball Catch
• For catch in jamb installations.
• Radiused corners allow easy installations with a router.
• Dual adjustment for door clearance and holding strength.
• Narrow strike is designed for use where strike is mounted in door.
• Free rolling ball insures smooth, positive and trouble-free action.
• Adjustable threaded barrel compensates for various door
clearances.
• Adjustable spring tension.
• Made from wrought brass.
• Conforms to ANSI/BHMA A156.9 B23013.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
D
E
U
IN
T
N
O
C
S
DI
Dimensions:
Face Plate: 2-1/8" x 1"
Bore: 7/8" x 1-3/8"
Strike: 2-1/8" x 1-1/16". Lip 9/16" to center
349 Ball Catch
• For catch in door installations.
• Radiused corners allow easy installation with a router.
• Dual adjustment for door clearance and holding strength.
• Lip strike is designed for use where strike is mounted in jamb.
• Free rolling ball insures smooth, positive and trouble-free action.
• Adjustable threaded barrel compensates for various door
clearances.
• Adjustable spring tension.
• Made from wrought brass.
• Conforms to ANSI/BHMA A156.9 B23013.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
G12
Dimensions:
Face Plate: 2-1/8" x 1"
Bore: 7/8" x 1-3/8"
Strike: 2-1/8" x 1-3/8". Lip 7/8" to center
Cupboard Latch and Push Latches
540 Cupboard Latch
• For cabinets or small doors.
• Surface applied, making installation simple.
• Made from cast brass.
• Conforms to ANSI/BHMA A156.9 B13243.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
D
E
U
IN
T
N
O
C
S
DI
Dimensions:
Case: 1-3/4" x 1-3/16"
Strike: 1-3/4" x 7/16"
820 Push Latch
• For use on cabinet doors.
• Push action opens and closes door.
• Ideal where concealed hardware is desired.
• Eliminates need for pulls or knobs; enhances styling and clean
appearance of fine furniture and cabinets.
• Simple installation; surface mounted, no mortising required.
• Narrow case design for low profile.
• Made from wrought steel.
• Conforms to ANSI/BHMA A156.9 B83333.
• Finishes: F2C, F3.
D
E
U
IN
T
N
O
C
S
DI
Dimensions:
2-11/32" x 1-1/2" x 11/32"
821 Touch Latch
• For use cabinet and small doors.
• Push action opens and closes door.
• Eliminates need for pulls or knobs.
• Made from wrought steel.
• Conforms to ANSI/BHMA A156.9 B83333.
• Finish: F2C.
D
E
U
IN
T
N
O
C
S
DI
Dimensions:
3" x 1-1/2" x 3/4"
G13
Mortise Door Bolts
S48 Mortise Door Bolt
• Brass oval turn knob and escutcheon.
• Steel bolt for extra strength. Rack is milled for precision fit with
pinion.
• Conforms to design requirements of ANSI A156.16.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
Dimensions:
Backset: 1-3/4"
Bolt Throw: 1/2"
Bolt Diameter: 1/2"
Case: 2-1/2" L x 9/16" diameter
Strike: 1-3/4" x 7/8"
150/152/154 Mortise Door Bolts
151/153/155 Mortise Door Bolts
• Only 1/4" turn of thumbturn or knob to lock or unlock door.
• 150, 152, 154 have solid brass thumbturn and escutcheon.
• 151, 153, 155 have solid brass oval turn knob and escutcheon.
• Precision molded, slim aluminum case treated for maximum rust
resistance.
• Heat-treated, copper impregnated allow steel hub for superior
strength and permanently lubricated cam action.
• Retains unequaled, smooth positive operation.
• Simplified installation—one-step mortise.
• Optional emergency release trim available.
• Conforms to design requirements of ANSI A156.16.
• 150, 152, 154 are packed with thumbturn, escutcheon, bolt, strike
and screws.
• 151, 153, 155 are packed with oval turn knob, escutcheon, bolt,
strike and screws.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Model
150
151
152
153
154
155
Backset
1-3/4"
1-3/4"
2-1/2"
2-1/2"
2-3/4"
2-3/4"
D
E
U
N
I
T
N
O
C
DIS
Case Dimension
1-5/8" x 2-1/4" x 9/16"
1-5/8" x 2-1/4" x 9/16"
1-5/8" x 3" x 9/16"
1-5/8" x 3" x 9/16"
1-5/8" x 3-1/4" x 9/16"
1-5/8" x 3-1/4" x 9/16"
Operation
Thumbturn
Oval turn knob
Thumbturn
Oval turn knob
Thumbturn
Oval turn knob
Trim Components
For use with Mortise Door Bolts 150, 151, 152, 153, 154,
155
• 5 Emergency Key.
• 145 Thumbturn for use with 150, 152, 154.
• 146 Escutcheon for use with 150, 152, 154.
• 145 x 146 Thumbturn and Escutcheon for use with 150, 152, 154.
• 147 Oval turn knob for use with 151, 153, 155.
• 148 Escutcheon for use with 151, 153, 155.
• 147 x 148 Oval Turn Knob and Escutcheon for use with 151, 153,
155.
Thumbturns, oval turn knobs, and escutcheons available in same
finishes as mortise door bolts
G14
Dimensions:
Face Plate on all models: 2-3/4" x 13/16"
Bolt Throw: 1/2"
Strike: 2-1/2" x 13/16"
Section H
Hooks and Brackets
Hand Rail Brackets
HB158 Hand Rail Bracket
• For use on commercial applications.
• Exceeds OSHA and BHMA strength test requirements.
• Cast aluminum construction.
• Packed with toggle bolt and screws.
• Meets ANSI/BHMA A156.16, L33101.
• Finishes: US3AL, US4AL, US5AL, US10AL, US14AL,
US27(A92), US28.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
3-1/8" Base Diameter
3-1/8" Base to Rail Center
HB159A
HB159B Hand Rail Bracket
• For use on commercial applications.
• Exceeds OSHA and BHMA strength test requirements.
• HB159B meets Uniform Federal Accessibility Standards,
paragraph 4.26.
• HB159B brass hand rail bracket conforms to ADA
guidelines when used in combination with 1-1/4" to 1-1/2"
diameter or equivalent shaped gripping surface.
• Packed with square head iron lag screw, expansion shield
and screws.
• Cast Brass construction for the HB159B.
• Cast Aluminum construction for the HB159A.
• HB159A meets ANSI/BHMA A156.16, L33081.
• HB159B meets ANSI/BHMA A156.16, L13081.
• Finishes: HB159B - US3, US4, US5, US10, US10B, US14, US15,
US15A, US26.
HB159A - US3AL, US4AL, US5AL, US10AL, US14AL,
US27(A92), US28.
Dimensions:
HB159A - 3-1/8" Base Diameter, 3-1/8" Base to Rail Center
HB159B - 3" Base Diameter, 2-1/4" Base to Rail Center
H1
Hand Rail Brackets
HB162 Adjustable Hand Rail Bracket
• For horizontal rail installations in institutional and
commercial buildings.
• Rust resistant.
• Exceeds OSHA and BHMA strength test requirements.
• Adjustable brackets compensate for irregularities in wall,
adjustable from 1-1/2" to 2" wall clearance.
• Stainless steel 1/4"-20 button head socket screw and stainless
steel self-locking hex nut provide strong, rigid assembly.
• Extruded aluminum construction.
• Finish: US28.
• Specify desired wall fasteners:
“W” for wood screws or “T” for toggle bolts.
How to Order:
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
2-3/4" Tall x 1-3/4" Wide
HB162 - ____ - ____
Finish:
US28
Fastener:
Blank
Screw with expansion shield
W
Wood screws only
T
Screw with toggle bolts
059 & 59 Hand Rail Bracket
• 059 made from solid brass, cast aluminum or epoxy-coated
aluminum.
• 59 made from cast brass or cast aluminum.
• Large faceplate for secure attachment to wall.
• Features solid construction for increased strength.
• 59 conforms to ANSI/BHMA A156.16 L13061 for brass and
L33061 for aluminum.
• Brass Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14,
B15 (B-619), B15A (B-620), B19, B26 (B-625), B26D.
• Aluminum Finishes: A3, A4, A5, A10, A10B, A14, A92.
• Epoxy-Coated Aluminum Finishes: White A-W, Black A-BLK,
Almond A-A.
H2
Dimensions:
059 Base: 2-1/4" H x 1-3/8" W
059 Base to Center of Rail: 2-7/16"
59 Aluminum Base: 2-13/16" H x 1-1/2" W
59 Brass Base: 2-15/16" H x 1-1/2" W
59 Base to Center of Rail: 2-3/4"
Hooks and Brackets
405 Coat & Hat Hook
• Wide body design is ideal for public buildings, schools,
dormitories, etc., where hook must withstand unusual stress and
strain.
• Made from cast aluminum.
• Conforms to ANSI/BHMA A156.16 L33113.
• Finishes: A3, A4, A5, A10, A14, A19, A92.
Dimensions:
Base: 1-1/2" H x 7/8" W
Projection: 2-1/2"
571 Coat & Hat Hook
• All-purpose hook in traditional design.
• Made from cast brass, cast aluminum, or epoxy-coated
aluminum.
• Conforms to ANSI/BHMA A156.16 L13113 for brass and L33113
for aluminum.
• Brass Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14,
B15 (B-619), B15A (B-620), B19, B26 (B-625), B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
• Epoxy-Coated Aluminum Finishes: White A-W, Black A-BLK,
Almond A-A.
Dimensions:
Base: 1-3/4" H x 1-1/4" W
Projection: 3"
572 Coat & Hat Hook
• Step-up decorative version of the traditional all-purpose hook.
• Ideal for locations where additional strength is required.
• Made from cast brass or cast aluminum.
• Conforms to ANSI/BHMA A156.16 L33112, L13113.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26,
B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
Dimensions:
Brass Base: 1-1/2" H x 1-5/16" W
Aluminum Base: 1-5/8" x 1-5/16"
Projection: 3"
H3
Hooks and Brackets
573 Coat & Hat Hook
• Great where economy is needed.
• Easily installed; no tools required.
• Made from steel.
• Finishes: F2C, F3.
• Projection: 3-1/8".
D
E
U
N
I
T
N
O
C
DIS
574 Coat & Hat Hook
• Decorative design is ideal for commercial and residential
installations.
• Made from cast brass, cast aluminum or epoxy-coated
aluminum.
• Conforms to ANSI/BHMA A156.16 L13113 for brass and L33113
for aluminum.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26,
B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A26, A92.
• Epoxy-Coated Aluminum Finishes: White A-W, Black A-BLK,
Almond A-A.
Dimensions:
Base: 1-5/8" H x 1-3/4" W
Projection: 3-3/4"
Overall Height, Brass: 4-3/4"
Overall Height, Aluminum: 5"
575 Coat & Hat Hook
• Especially designed to accommodate large hats.
• Made from solid brass or cast aluminum.
• Conforms to ANSI/BHMA A156.16 L33121.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26,
B26D.
• Aluminum Finishes: A3, A4, A5, A10, A10B, A14, A92.
Dimensions:
Base: 2-1/4" H x 1-3/8" W
Projection: 3-5/8"
Overall Height: 5-3/4"
H4
Hooks and Brackets
580 Ceiling Hook
• Ideal for use in closets, attached to underside of shelves, or in
storage lockers.
• Made from cast brass or cast aluminum.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26,
B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
Dimensions:
Base, Brass: 7/8" H x 1-15/16" W
Base, Aluminum: 1" H x 1-7/8" W
Projection: 2-1/4"
581 Wardrobe Hook
• Compact hook is perfect where space is limited, such as behind
doors where low profile is needed.
• Made from cast brass, cast aluminum or epoxy-coated
aluminum.
• Brass Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14,
B15 (B-619), B15A (B-620), B19, B26 (B-625), B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
• Epoxy-Coated Aluminum Finishes: White A-W, Black A-BLK,
Almond A-A.
Dimensions:
Base: 1-1/4" H x 1-1/4" W
Projection, Brass: 1-11/16"
Projection, Aluminum: 1-5/8"
582 Double Wardrobe Hook
• Compact double hook is perfect where space is limited, such as
behind doors where low profile is needed.
• Made from cast brass, cast aluminum or epoxy-coated
aluminum.
• Brass Finishes: B3 (B-605), B4, B5, B10, B10B (B-613), B14,
B15 (B-619), B15A (B-620), B19, B26 (B-625), B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
• Epoxy-Coated Aluminum Finishes: White A-W, Black A-BLK,
Almond A-A.
Dimensions:
Base, Brass: 1-1/8" H x 1-1/4" W
Base, Aluminum: 1-1/16" H x 1-3/16 W
Projection, Brass: 1"
Projection, Aluminum: 1-3/32"
H5
Hooks and Brackets
583 & 587 Line Cleat
• Ideal for window shades, flags and other tie-down applications.
• Made from solid brass, cast aluminum or epoxy-coated
aluminum.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26,
B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
• 587 also available in: White A-W, Black A-BLK, Almond A-A.
D
E
U
N
I
T
N
O
C
DIS
Dimensions:
583: 4-1/2" Long, 13/16" Projection
587: 2-1/2" Long, 1/2" Projection
585 Closet Pole Sockets
• Flange design prevents accidental knock out of pole.
• Made from wrought steel.
• Accommodates pole or pipe with outside diameter of 1-3/8".
• Packed in pairs.
• Finish: F3.
586 Closet Pole Sockets
• Made from a heavy duty plastic for long life and extra strength.
• Single screw mounting.
• Accommodates pole or pipe with outside diameter of 1-3/8".
• Packed in pairs.
• Finish: White plastic.
H6
Notes
H7
Notes
H8
Section I
Window Hardware
Window Hardware - Locks
4 Window Lock
07 Window Lock
• Spring actuated lever provides positive direct pull which pulls rails
together.
• Stops rattles and drafts.
• When unlocking, lever automatically returns to opened position.
• Made from solid brass or wrought steel.
• Meets design requirements of ANSI/BHMA 156.16.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26,
B26D.
• Steel Finishes: F3, F4, F10, F14, F15, F15A, F26, F26D.
• Designed low to the sash for superior strength and greater
resistance to breakage.
• Vertical and horizontal camming action for snug, non-rattling fit.
• Heavy gauge springs provide long-wearing action.
• Made from solid brass, aluminum, or epoxy coated aluminum.
• Meets design requirements of ANSI/BHMA 156.16.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19,
B26, B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
• Epoxy-Coated Aluminum Finishes: White A-W, Black A-BLK,
Almond A-A.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Base: 1-3/8" x 2-5/16"
Strike: 9/16" x 2-1/4"
Dimensions:
Base: 15/16" x 2-9/16"
Strike: 5/8" x 2-9/16"
9 Window Lock
1401 Window Lock
• Designed low to the sash for superior strength and greater
resistance to breakage.
• Vertical and horizontal camming action for snug, non-rattling fit.
• Heavy gauge springs provide long-wearing action.
• Made from solid brass.
• Meets design requirements of ANSI/BHMA 156.16.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
•
•
•
•
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Base: 1-1/16" x 2-7/8"
Strike: 5/8" x 3"
Low silhouette and modern design.
Lifts up and draws meeting rails tightly together.
Locks securely and eliminates drafts and rattles.
Unique strike design prevents damage to upper sash because
fastener must be completely unlocked before window can be
opened.
• Made from solid brass or aluminum.
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26,
B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Base: 13/16" x 2-7/8"
Strike: 7/16" x 2-7/8"
I1
Window Hardware - Locks
0 Open Window Lock
90 Side Window Lock
• For locking double hung windows in open position.
• Window unit may be left open at top or bottom or both top and
bottom.
• Ideal for use where air conditioning unit or fan is used.
• Made from wrought steel.
• Meets ANSI/BHMA 156.16.
• Finish: F3.
• May be used singularly for small windows or in pairs for large
windows.
• Cam action eliminates rattles and holds window firmly in desired
position.
• Made from aluminum.
• Finish: A3.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Plate: 1-9/16" x 1-3/8"
Projection: 5/8"
Strike: 1" x 3/4"
I2
Dimensions:
Size: 1-3/4" x 1-1/8"
Window Hardware - Lifts and Pulls
14 Hook Window Lift
026 Bar Window Lift
•
•
•
•
•
•
•
•
•
Facilitates opening of window in a safe manner.
May be used singularly or in pairs.
Made from solid brass or steel.
Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26,
B26D.
• Steel Finishes: F3, F4, F10, F14, F15, F15A, F26, F26D.
Facilitates opening of window in a safe manner.
Can also be used as a drawer or utility pull.
Made from solid brass, aluminum, or epoxy coated aluminum.
Meets ANSI/BHMA A156.16.
Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A,
B19, B26, B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
• Epoxy-Coated Aluminum Finishes: White A- W, Black A-BLK,
Almond A-A.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Base: 7/8" x 1-5/8"
Projection: 3/4"
Dimensions:
Base: 1-1/8" x 4"
Projection: 1-1/16"
26 Bar Window Lift/Utility Pull
27 Bar Window Lift/Utility Pull
•
•
•
•
•
•
•
•
•
•
Facilitates opening of window in a safe manner.
Can also be used as a drawer or utility pull.
Made from solid brass.
Meets ANSI/BHMA A156.16.
Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19,
B26, B26D.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Base: 1-1/8" x 4-3/4"
Projection: 1-1/8"
Facilitates opening of window in a safe manner.
Can also be used as a drawer or utility pull.
Made from solid brass.
Meets ANSI/BHMA A156.16.
Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26,
B26D.
ED
U
N
NTI
O
C
DIS
Dimensions:
Base: 1-3/8" x 5"
Projection: 1-1/4"
I3
Window Hardware
066 Casement Fastener
66 Casement Fastener
• For use on windows to provide weather-tight fastening and
security.
• Also ideal for securing louvered doors and small doors.
• Made from solid brass or aluminum.
• Meets ANSI/BHMA A156.16.
• Specify: Surface ,
Rim , or
Mortise
Strike (SS)
Strike (RS)
Strike (MS)
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19,
B26, B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
• For use on windows to provide weather-tight fastening and
security.
• Also ideal for securing louvered doors and small doors.
• Made from solid brass or aluminum.
• Meets ANSI/BHMA A156.16.
• Specify: Surface ,
Rim , or
Mortise
Strike (SS)
Strike (RS)
Strike (MS)
• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A,
B26, B26D.
• Aluminum Finishes: A3, A4, A5, A10, A14, A92.
Dimensions:
Base: 1-5/8" x 7/8"
Projection: 1-3/8"
Dimensions:
Base: 2-1/16" x 1-1/16"
Projection: 1-7/8"
287 Friction Casement Adjuster
288 Friction Casement Adjuster
• Securely holds casement window in any position.
• Friction construction allows flexible positions without manual
adjustment.
• Can also be used to hold cabinet lids in various positions.
• Made from solid brass.
• Available in 8", 10" and 12" lengths.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
• Securely holds casement window in any position.
• Friction construction allows flexible positions without manual
adjustment.
• Features positive locking.
• Can also be used to hold cabinet lids and drafting table tops in
various positions.
• Made from solid brass.
• Available in 10" and 12" lengths.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
D
E
U
TIN
N
CO
S
I
D
I4
ED
U
N
TI
N
CO
S
I
D
Dimensions:
Dimensions:
Tube: 3/8" x 5/8"
Projection: 1"
Tube: 3/8" x 5/8"
Projection: 1"
Window Hardware
31 Shutter Bars
71 Casement Adjuster
• Ideal for bi-fold doors and shutters.
• Shoulder rivet insures free swinging bar.
• Convex styling of bar for better finger grip and convenient operation.
• Made from cast brass.
• Packed with brass oval head screws.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
• Securely holds casement window in any position.
• Can also be used to hold cabinet lids and drafting table tops in
various positions.
• Made from burnished steel or solid brass.
• Available in 10" and 12" lengths.
• Finishes: B3, F3, F4, F5, F10, F14.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Base: 7/8" x 1-1/2"
Hook Centers: 1-3/8"
Projection: 7/16"
Dimensions:
Tube: 3/8" x 5/8"
Projection: 1"
Sash Plate:
Brass: 1-5/8" x 5/8"
Steel: 2 x 5/8"
Sill Plate:
2-1/4" x 15/16"
80 Transom Catch
82 Transom Chain
• Independent latch action; transom can be closed by pushing
directly on ring.
• Reversible: latch bolt can be easily reversed by removing back plate.
• Narrow base accommodates 1-1/4" rail.
• Made from cast brass or cast aluminum.
• When ordering, specify Universal Strike (US) or Rim Strike (RS).
• Conforms to design requirements of ANSI/BHMA A156.16.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, A3,
A4, A5, A10, A14, A92.
• Available in 10", 12" and 15" chain lengths to meet varying opening
requirements and transom sizes.
• Made from wrought steel.
• Plate Size: 1-1/2" x 1".
• Finishes: F3, F4, F10, F14, F26D.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Size: 2-1/4" x 1-1/4"
Latch Throw: 5/16"
ED
U
N
TI
N
CO
S
I
D
Universal Strike Shown
I5
Window Hardware
350 Adjustable Catch
PRS375 Shutter Holdbacks
• Recommended for casement windows and large doors.
• Pulls window or door in for tight fit.
• Easily adjustable tension from 5 lbs. to 10 lbs.
• No mortising necessary; no latch or lock required.
• Made from wrought steel.
• Finish: F2C.
• Designed for easy opening and closing of shutters.
• Rustproof "S" hook designed for long life.
• Specially-designed rustproof spring stops shutter rattle.
• Packed with anti-rattle spring and lag screw.
• Made from cast aluminum.
• Sold in pairs.
• Finish: A19.
ED
U
N
TI
N
CO
S
I
D
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Catch: 4" x 1" x 1"
Strike: 3-3/4" x 1/2" x 3/4"
6 Window Stop Adjusters
1 Countersunk Washers
• Elongated hole facilitates proper positioning of window stop
against window.
• Mortised into window stop.
• Made from wrought steel.
• Finishes: F3, F10B, F14.
• Made from wrought brass.
• For use with screw numbers 6, 8, 10, 12 and 14.
• Packed in bags of 100.
• Finishes: B3, B14.
D
E
U
TIN
N
CO
S
I
D
D
E
U
TIN
N
CO
S
I
D
Dimensions:
Pan Head Screws: 1" x 8
Stop Diameter: 5/8"
I6
Product No.
Outside Diameter
1 – NO6
7/16"
1 – NO8
1/2"
1 – NO10
19/32"
1 – NO12
5/8"
1 – NO14
25/32"
Notes
I7
Notes
I8
Section J
Hinges
General Architectural Hinge Information
SELECTION OF THE PROPER WEIGHT AND BEARING TYPE
Standard Weight . . . . Plain Bearing
Standard Weight . . . . Ball Bearing, Concealed Bearing
Heavy Weight . . . . . . . Ball Bearing, Concealed Bearing
Considerations to determine Weight and Bearing type:
1. Weight of Door
2. Frequency of use
3. Frame
4. Door Hardware
Always use ball bearing or concealed bearing hinges for doors with
door closers and in all fire rated openings. Heavy weight doors
and high frequency doors should use heavy weight ball bearing or
concealed bearing hinges.
Considerations to determine Hinge Size
1. Door Width
2. Door Thickness
3. Weight
4. Clearance
GUIDELINES FOR ARCHITECTURAL HINGE HEIGHT
DOOR THICKNESS
IN INCHES
1-3/8”
1-3/8
1-3/4
1-3/4
1-3/4
2”, 2-1/4”, 2-1/2”
2”, 2-1/4”,2-1/2”
DOOR WIDTH
IN INCHES
Up to 32”
32” to 37”
Up to 36”
36” to 48”
Over 48”
Up to 42”
Over 42”
HINGE HEIGHT
IN INCHES
3-1/2
4”
4-1/2”
5”
6”
5” heavy weight
6” heavy weight
GUIDELINES FOR FREQUENCY OF DOOR USAGE:
GUIDELINES FOR ARCHITECTURAL HINGE WIDTH
Build Type
Daily
Usage
High Frequency/ Heavy Weight Door
Large Department Store Entrance
5,000
Hospital Corridor and Surgical Doors
5,000
Large Office Building Entrance
4,000
School Entrance
1,250
School Toilet Door
1,250
Office Stairwell
500
Office Building Toilet Door
400
Yearly
Usage
Heavy Weight
1,825,000
1,825,000
1,460,000
456,250
456,250
182,500
146,000
Medium Frequency/ Medium Weight Door
School Corridor Door
Hospital Consultation Rooms
Office Building Corridor Door
Store Toilet Door
Storage Room
Low Frequency /Light Door
Residential Entrance
Interior Residential
100
100
80
60
50
Hinge
Type
Standard Weight
36,500
36,500
29,200
21,900
18,250
DOOR THICKNESS
1-3/8
CLEARANCE NEEDED
3/4
HINGE OPEN WIDTH
4
1-3/4
1
4
-
1-1/2
4-1/2
-
2
5
-
3
6
2
1
4-1/2
-
1-1/2
5
-
2-1/2
6
2-1/4
1
5
-
2
6
2-1/2
3/4
5
-
1-3/4
6
3
3/4
8
-
2-3/4
8
-
4-3/4
10
Plain Bearing
30
20
10,950
7,300
Minimum Architectural Cycle requirements
Grade 1:
Grade 2:
Grade 3:
2,500,000 Heavy Weight Ball & Concealed Bearing
1,500,000 Standard Weight Ball & Concealed Bearing
350,000 Light Weight Plain Bearing
J1
General Architectural Hinge Information
GUIDELINES FOR NUMBER OF ARCHITECTURAL HINGES
1. Doors up to 60”…… 2 hinges
2. Doors 60" to 90".….. 3 hinges
3. Doors 90" to 120" …. 4 hinges
IVES ARCHITECTURAL HINGE FINISHES
LOCATION OF ARCHITECTURAL HINGES
IVES
600
605
606
612
613
619
B.H.M.A SYMBOL
BASE MATERIAL
STEEL
Top hinge 5" from jamb
rabbet to top of barrel
Bottom hinge 10" from
bottom edge of barrel to
finished floor
Third hinge centered
between top and bottom
hinges
Note: Certain western
states use a standard 7"
from top and 11"
From the bottom
GUIDELINES FOR ARCHITECTURAL HINGE METAL
1.
2.
3.
4.
630
632
633
639
640
641
643
Interior doors or non-corrosive areas use: Plated or painted Steel
Interior labeled door use: Plated or Painted Steel, Stainless Steel
Interior doors in corrosive areas use: Stainless Steel , Brass, Bronze
Exterior doors use: Stainless Steel, Brass, Bronze
646
651
652
DESCRIPTION
Primed for painting
Bright Brass, clear coated
Satin Brass, clear coated
Satin Bronze, clear coated
Oil Rubbed Satin Bronze
Satin Nickel Plated,
clear coated
Satin Stainless Steel
Bright Brass Plated,
clear coated
Satin Brass Plated,
clear coated
Satin Bronze Plated,
clear coated
Oil Rubbed Satin Bronze
Antique Bronze, Plated,
Relieved, clear coated
Satin Bronze Plated,
Blackened
Satin Nickel Plated,
clear coated
Bright Chromium Plated
Satin Chromium Plated
BRASS
600
605
606
612
613
619
STAINLESS U.S.
STEEL
Equivalent
USP
US3
US4
US10
US10B
US15
632
630
US32D
US3
633
US4
639
US10
640
641
US10B
US10A
643
US11
646
US15
651
652
US26
US26D
MODEL NUMBER COMPARISON CHART
TYPE
STEEL PLAIN BEARING
STAINLESS PLAIN BEARING
STEEL CONCEALED BEARING
STAINLESS CONCEALED BEARING
STEEL CONCEALED BEARING HEAVY WEIGHT
STAINLESS CONCEALED BEARING HEAVY WEIGHT
BRASS CONCEALED BEARING HEAVY WEIGHT
STEEL BALL BEARING
STAINLESS BALL BEARING
STEEL BALL BEARING HEAVY WEIGHT
STAINLESS BALL BEARING HEAVY WEIGHT
STEEL SWING CLEAR
J2
ANSI
A8133
A5133
A8112
A5112
A8111
A5111
A2111
A8112
A5112
A8111
A5111
A8122
IVES
3PB1
3PB1
3CB1
3CB1
3CB1HW
3CB1HW
3CB1HW
5BB1
5BB1
5BB1HW
5BB1HW
5BBSC1
HAGER
700
800
AB700
AB800
AB750
AB850
AB850
BB1279
BB1191
BB1168
BB1199
BB1260
MCKINNEY
T714
NA
TA714
TA314
TA786
TA386
TA386
TB2714
TB2314
T4B3786
T4B3386
TB2895
STANLEY
FBB179
FBB191
FBB168
FBB199
FBB248
BOMMER
8000
8002
LB8000
LB8002
LB8004
LB8006
LB8005
BB5000
BB5002
BB5004
BB5006
BB8020
PBB
CP81
CP51
CB81
CB51
4C81
4C51
4B21
BB81
BB51
4B81
4B51
SC81
General Architectural Hinge Information
Ives Hinge Number System
Please note: For availability of specific models, please refer to the item’s catalog page or consult Customer Service.
How to Order:
____ - ____- ____ - ____- ____ - ____- ____ - ____
Number of Knuckles:
3 - 3 Knuckle
5 - 5 Knuckle
Function:
PB
BB
CB
SP
Plain Bearing
Ball Bearing
Concealed Bearing
Spring Hinge
Type:
1
2
3
4
Full Mortise
Half/Mortise
Full Surface
Half Surface
Weight/Options:
Blank
Standard Weight
HW
Heavy Weight
SC
Swing Clear
SH
Security Stud
WT
Wide Throw
ST
High Security Stud
HT
Hospital Tips
Size Examples:
4.5 x 4
4.5 x 4.5
5 x 4.5
Finish (Some models are not available in all finishes):
600
USP - Steel
605
US3 - Brass
606
US4 - Brass
612
US10 - Brass
613
US10B - Brass
619
US15 - Brass
630
US32D - Stainless
632
US3 - Steel
633
US4 - Steel
639
US10 - Steel
640
US10B - Steel
641
US10A - Steel
643
US11 - Steel
646
US15 - Steel
651
US26 - Steel
652
US26D - Steel
Special Pins Applications:
NRP
Non-Removable Pin
HT
Hospital Tip
TW4
Four Wire
TW8
Eight Wire
MON
Monitor
TW4M Four Wire with Monitor
TW8M Eight Wire with Monitor
J3
FULL MORTISE HINGES - 3 KNUCKLE
PLAIN BEARING • LOW FREQUENCY • STANDARD WEIGHT
For use on Medium Weight Doors with Low Frequency Usage,
not intended for use with door closing devices
3PB1 Steel with steel pin.
3PB1 Brass with stainless pin.
3PB1 Stainless Steel with stainless steel pin. (630 finish only)
• Dimensions & tolerances conform to ANSI - A156.7.
• 3PB1 Steel Description conforms to ANSI - A8133.
• 3PB1 Stainless Description conforms to ANSI - A5133.
• Packed with wood and machine screws.
Size (Inches)
Size (MM)
Gauge
4.5 x 4
114 x 102
.134
4.5 x 4.5
114 x 114
.134
CONCEALED BEARING • MEDIUM FREQUENCY • STANDARD WEIGHT
For use on Medium Weight Doors with Medium Low Frequency Usage
3CB1 Steel with steel pin.
3CB1 Brass with stainless pin.
3CB1 Stainless Steel with Stainless Steel pin. (630 finish only)
Non- Removable Pin suffix “NRP”.
• Dimensions & tolerances conform to ANSI - A156.7.
• 3CB1 Steel description conforms to ANSI - A8112.
• 3CB1 Stainless description conforms to ANSI – A5112.
• Packed with wood and machine screws.
Size (Inches)
Size (MM)
Gauge
4.5 x 4
114 x 102
.134
4.5 x 4.5
114 x 114
.134
CONCEALED BEARING • HIGH FREQUENCY • HEAVY WEIGHT
For use on Heavy Weight Doors or High Frequency Usage
3CB1HW Steel with steel pin
3CB1HW Brass with stainless pin
3CB1HW Stainless Steel with stainless pin (630 finish only)
Non- Removable Pin suffix “NRP”
• Dimensions & tolerances conform to ANSI - A156.7
• 3CB1HW Steel description conforms to ANSI - A8111
• 3CB1HW Stainless description conforms to ANSI – A5111
• 3CB1HW Brass description conforms to ANSI – A2111
• Packed with wood and machine screws
Size (Inches)
J4
Size (MM)
Gauge
4.5 x 4
114 x 102
0.180
4.5 x 4.5
114 x 114
0.180
5 x 4.5
127 x 114
0.190
FULL MORTISE HINGES - 3 KNUCKLE
SPRING HINGE
For automatic closing of door.
3SP1
3SP1
Steel with steel pin
Stainless Steel with stainless pin (630 finish only)
• UL listed for use with fire rated doors.
• Packed with wood and machine screws.
Size (Inches)
4.5 x 4.5
Size (MM)
Gauge
114 x 114
0.134
PLAIN BEARING • LOW FREQUENCY • STANDARD WEIGHT
For use on Medium Weight Doors with Low Frequency Usage, not intended for use with door closing devices.
5PB1 Steel with steel pin
5PB1 Brass with stainless pin
5PB1 Stainless Steel with stainless steel pin (630 finish)
Non-Removable Pin Suffix “NRP”
• Dimensions & tolerances conform to ANSI - A156.7.
• Packed with wood and machine screws.
Size (Inches)
Size (MM)
Gauge
4.5 x 4.5
114 x 114
.134
4.5 x 4
114 x 102
.134
2 BALL BEARING • MEDIUM FREQUENCY • STANDARD WEIGHT
For use on Standard Weight Doors with Medium Frequency Usage
5BB1 Steel with steel pin
5BB1 Brass with stainless pin
5BB1 Stainless Steel with stainless steel pin (630 finish only)
Non-Removable Pin suffix “NRP”
• Dimensions & tolerances conform to ANSI - A156.7.
• 5BB1 Steel description conforms to ANSI - A8112.
• 5BB1 Stainless description conforms to ANSI – A5112.
• Packed with wood and machine screws.
Size (Inches)
Size (MM)
Gauge
4.5 x 4.5
114 x 114
.134
4.5 x 4
114 x 102
.134
5 x 4.5
127 x 114
.134
J5
FULL MORTISE HINGES - 5 KNUCKLE
2 BALL BEARING • MEDIUM FREQUENCY • STANDARD WEIGHT • HIGH SECURITY STUDS
3/8" studs protrude through opposing leaves and into the frame.
5BB1ST Steel with steel pin
5BB1ST Stainless Steel with stainless steel pin (630 finish only)
• Dimensions & tolerances conform to ANSI - A156.7.
• 5BB1SH Steel description conforms to ANSI - A8112.
• 5BB1SH Stainless description conforms to ANSI – A5112.
• Packed with wood and machine screws.
Size (Inches)
4.5 x 4.5
Size (MM)
Gauge
114 x 114
.134
4 BALL BEARING • HIGH FREQUENCY • HEAVY WEIGHT
For use on Heavy Weight Doors or High Frequency Usage
5BB1HW Steel with steel pin
5BB1HW Brass with stainless pin
5BB1HW Stainless Steel with stainless steel pin (630 finish only)
Non-Removable Pin suffix “NRP” strike
• Dimensions & tolerances conform to ANSI - A156.7.
• 5BB1HW Steel description conforms to ANSI - A8111.
• 5BB1HW Stainless description conforms to ANSI – A5111.
• Packed with wood and machine screws.
Size (Inches)
Size (MM)
Gauge
4.5 x 4.5
5 x 4.5
114 x 114
127 x 114
0.180
0.190
2 BALL BEARING • MEDIUM FREQUENCY • STANDARD WEIGHT • SWING CLEAR
Designed to completely clear the opening when door is opened 92 degrees. Pins and tips are reversible.
5BB1SC Steel with steel pin
5BB1SC Stainless Steel with stainless steel pin (630 finish only)
• Dimensions & tolerances conform to ANSI - A156.7.
• 5BB1SC Steel Description conforms to ANSI - A8133.
• 5BB1SC Stainless Description conforms to ANSI - A5121.
• Packed with flat head wood and machine screws.
Size (Inches)
4.5
5
J6
Size (MM)
Gauge
114
127
0.134
0.134
FULL MORTISE HINGES - 5 KNUCKLE
2 BALL BEARING • MEDIUM FREQUENCY • HEAVY WEIGHT • SWING CLEAR
Designed to completely clear the opening when door is opened 92 degrees. Pins and tips are reversible.
5BB1SCHWB
5BB1SCHWB
Steel with steel pin
Stainless Steel with stainless steel pin (630 finish only)
• Dimensions & tolerances conform to ANSI - A156.7.
• 5BB1SCHWB Steel Description conforms to ANSI - A8133.
• 5BB1SCHWB Stainless Description conforms to ANSI - A5121.
• Packed with flat head wood and machine screws.
Size (Inches)
4.5
5
Size (MM)
Gauge
114
127
0.134
0.134
4-WIRE • 8-WIRE • HIGH FREQUENCY • HEAVY WEIGHT • SWING CLEAR
For use on Heavy Weight Doors or High Frequency Usage
4-Wire (TW 4 Suffix)
8-Wire (TW 8 Suffix)
Monitor (MON Suffix)
Through-Wire with monitor (TW4M Suffix or TW8M)
•
•
•
•
•
•
•
Available in 3 and 5 Knuckle
Listed under UL 634
Available in most models in current IVES hinge offering
One hinge per box, packed with wood and machine screws
High quality brass ferrules and plastic tubing protect the wires
Through-wire hinges cycle tested to ensure durability
Ives warranty applies - 12 months from date of shipment
Size (Inches)
Size (MM)
Gauge
4.5 x 4.5
5 x 4.5
114 x 114
127 x 114
0.180
0.190
2 BALL BEARING • MEDIUM FREQUENCY • STANDARD WEIGHT • HIGH SECURITY STUDS
3/8" studs protrude through opposing leaves and into the frame.
3BB1ST Steel with steel pin
3BB1ST Stainless Steel with stainless steel pin (630 finish only)
• Dimensions & tolerances conform to ANSI - A156.7.
• 3BB1SH Steel description conforms to ANSI - A8112.
• 3BB1SH Stainless description conforms to ANSI – A5112.
• Packed with wood and machine screws.
Size (Inches)
4.5 x 4.5
Size (MM)
Gauge
114 x 114
.134
J7
RESIDENTIAL HINGES
1000 Series Residential Hinges
• Full mortise hinges in 3 sizes: 3", 3-1/2" and 4".
• Two corner options: Square corner and 5/8" radius corners.
• Made from solid brass or stainless steel.
• Finishes: B-505 (Ultima Lifetime Anti-Tarnish), B-613, B-619,
B-620 and B-625
Model
1000
1001
1010
1011
1020
1021
J8
Size
Corner
3" x 3"
3" x 3"
3-1/2" x 3-1/2"
3-1/2" x 3-1/2"
4" x 4"
4" x 4"
Square Corner
5/8" Radius Corner
Square Corner
5/8" Radius Corner
Square Corner
5/8" Radius Corner
1000
1011
D
UE
TIN
ON
C
DIS
1001
1020
1010
1021
Section K
Cabinet/Closet Knobs
and Pulls
Cabinet/Closet Knobs and Pulls
513 Knob Backplate
• For use with Ives cabinet knobs 521, 523, 524, 530 and 535.
• Available in two diameters: 1-1/2" and 1-3/4".
• Provides a finishing touch. Especially useful to cover holes or marks
in replacement or remodeling applications.
• Made from wrought brass.
• 3/64" thick backplate. (This increases the projection of knob or pull.)
• Conforms to ANSI/BHMA A156.9 B22181.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Models:
513 1 1/2IN
513 1 3/4IN
D
E
U
N
I
T
N
O
C
DIS
521 Round Knob
• Available in four diameters: 3/4", 1", 1-1/4" and 1-1/2".
• Made from wrought brass.
• Furnished with a No. 8-32 machine screw, 1-1/8" long.
• Conforms to ANSI/BHMA A156.9 B22131.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Model & Diameter
521 3/4IN
521 1IN
521 1 1/4IN
521 1 1/2IN
D
E
U
TIN
N
CO
S
I
D
Projection
3/4"
15/16"
1-1/8"
1-5/16"
523 Colonial Knob
• Available in four diameters: 5/8", 1", 1-1/4" and 1-1/2".
• Made from wrought brass.
• Furnished with a No. 8-32 machine screw.
• Conforms to ANSI/BHMA A156.9 B22131.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Model & Diameter
523 5/8IN
523 1IN
523 1 1/4IN
523 1 1/2IN
D
E
U
TIN
N
CO
S
I
D
Projection
5/8"
15/16"
1"
1-7/32"
Screw Length
1"
1-1/8"
1-1/8"
1-1/8"
K1
Cabinet/Closet Knobs and Pulls
524 Round Knob
• Available in five diameters: 5/8", 3/4", 1", 1-1/4" and 1-1/2".
• Made from wrought brass. 1",1-1/4" and 1-1/2" diameter knobs
also made from anodized aluminum or epoxy-coated aluminum.
• Furnished with a No. 8-32 machine screw.
• Conforms to ANSI/BHMA A156.9 B22131 for brass, B42131 for
aluminum.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D. 1",
1 1/4" and 1 1/2" knobs also available in PA-A (almond), PA-W
(white), PA-BLK (black).
Model & Diameter
524 5/8IN
524 3/4IN
524 1IN
524 1 1/4IN
524 1 1/2IN
Projection
5/8"
23/32"
7/8"
1-1/32"
1-7/32"
D
E
U
N
I
T
N
O
C
DIS
Screw Length
1"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
530 Ball Knob
• Available in two diameters: 1" and 1-1/4".
• Made from wrought brass.
• Furnished with a No. 8-32 machine screw.
• Conforms to ANSI/BHMA A156.9 B22131.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
Model & Diameter
530 1IN
530 1 1/4IN
Projection
1-1/4"
1-1/2"
D
E
U
TIN
N
CO
S
I
D
Screw Length
1-1/8"
1-1/8"
535 Oval Knob
• Available in two sizes: 1-1/8" and 1-3/8".
• Made from wrought brass.
• Furnished with a No. 8-32 machine screw.
• Conforms to ANSI/BHMA A156.9 B22131.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
Model & Size (Height)
535 1 1/8IN
535 1 3/8IN
K2
D
E
U
TIN
N
CO
S
I
D
Knob Width
13/16"
1"
Projection
1-5/32"
1-3/8"
Screw Length
1-1/8"
1-1/8"
Cabinet/Closet Knobs and Pulls
33/34 Wire Pull
• Made from wrought brass.
• Furnished with No. 8-32 machine screws, 1" long.
• Conforms to ANSI/BHMA A156.9 B22011.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
Model
33
34
Center-to-Center
5"
6"
D
E
U
TIN
N
O
Overall Size C
Projection
5-5/16"IS 1-5/16"
D
6-5/16"
1-5/16"
36/37/38 Wire Pull
• Made from wrought brass, aluminum, or epoxy-coated aluminum.
• Furnished with a No. 8-32 machine screw, 1" long.
• Conforms to ANSI/BHMA A156.9 B22011 for brass, B42011 for
aluminum.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, PA28,
PA-A (almond), PA-W (white), PA-BLK (black).
Model
36
37
38
Center-to-Center
3"
3-1/2"
4"
D
E
U
TIN
N
O
CProjection
Overall Size
S
I
3-5/16"
1-5/16"
D
3-13/16"
1-5/16"
4-5/16"
1-5/16"
133 Beaded Pull
• Available in three center-to-centers: 3", 3-1/2", and 4".
• Made from wrought brass.
• Furnished with a No. 8-32 machine screw, 1" long.
• 133 3IN and 133 3-1/2IN are packaged with base washers 504.
• Conforms to ANSI/BHMA A156.9 B22011 for brass.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
Model
133
133
133
Center-to-Center
3IN
3 1/2IN
4IN
D
E
U
TIN
N
O
Overall Size C
Projection
3-3/8" IS 1-1/8"
D
3-7/8"
1-1/8"
4-3/8"
1-1/8"
K3
Cabinet/Closet Knobs and Pulls
137 Drawer Pull
• Made from cast brass or aluminum.
• Furnished with a No. 8-32 machine screw, 1" long.
• Conforms to ANSI/BHMA A156.9 B12011 for brass and 42011 for aluminum.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, PA28.
Model
137
Center-to-Center
3"
ED
U
TIN
N
CO
Overall Size
DIS Projection
3-1/2"
7/8"
504 Wire Pull Base Washers
ED
U
N
NTI
O
C
DIS
• For use with Ives 33, 34, 36, 37, 38, 133-3IN and 133-3-1/2IN wire
pulls.
• Made from wrought brass.
• 5/8" diameter.
• 3/64" thickness (This increases the projection of pull.)
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
540 Cupboard Latch
• For cabinets or small doors.
• Surface applied, making installation simple.
• Made from cast brass.
• Conforms to ANSI/BHMA A156.9 B13243.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.
ED
U
N
NTI
O
C
DIS
Dimensions:
Case: 1-3/4" x 1-3/16"
Strike: 1-3/4" x 7/16"
2 Elbow Catch
• Ideal for use on the inactive leaf of a pair of cabinet doors.
• Surface applied, making installation simple.
• Made from cast brass or cast aluminum.
• Conforms to design requirements of ANSI/BHMA A156.9.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D, A3,
A4, A5, A10, A14, A92.
Dimensions:
Plate: 1-3/8" x 5/8"
Strike: 13/16" x 5/8"
K4
Cabinet/Closet Knobs and Pulls
22 Flush Pull
• Low profile makes this pull ideal for louvered, bi-folding or wardrobe
doors.
• Extra deep recess and reverse tapered grip provide for ease of
pulling and gripping.
• Made from wrought brass.
• Conforms to design requirements of ANSI/BHMA A156.9 B22201
and A156.14 D2781.
• Finishes: B3, B4, B5, B10, B10B, B14, B15 (B-619), B15A (B-620),
B19, B26 (B-625), B26D, B-619, B-620, B-625.
Dimensions:
1-5/16" H x 3-1/8" W x 7/16" D
218 Finger Pull
• Ideal for use on sliding doors.
• Easy installation.
• Made from wrought brass.
• Conforms to design requirements of ANSI/BHMA A156.9 B22201
and A156.14 D2781.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
Inside Cup Diameter: 3/4"
Overall Diameter: 1"
Depth: 5/16"
220/221 Flush Pull
• Ideal for use on sliding doors.
• Built-in prong design eliminates the need for screws or brads and
facilitates installation.
• Packed with two escutcheon pins for added holding power.
• Made from wrought brass.
• Conforms to design requirements of ANSI/BHMA A156.9 B22201
and A156.14 D2781.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
220 Inside Cup Diameter: 2"
220
Overall Diameter: 2-3/8"
DISCONTINUED
220 Depth: 7/16"
221 Inside Cup Diameter: 2-1/8"
221 Overall Diameter: 2-7/16"
221 Depth: 7/16"
K5
Cabinet/Closet Knobs and Pulls
222 Flush Pull
• Low profile makes this pull ideal for louvered, bi-folding or wardrobe doors.
• Reverse tapered grip provide for ease of pulling.
• Made from cast brass.
• Conforms to design requirements of ANSI/BHMA A156.9 B12201 and
A156.14 D1781.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
3-1/8" H x 1-5/8" W x 7/16" D
223 Flush Pull
• Low profile makes this pull ideal for louvered, bi-folding or
wardrobe doors.
• Made from wrought brass.
• Conforms to design requirements of ANSI/BHMA A156.9 B22201
and A156.14 D2781.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
3-9/16" H x 1-5/16" W x 1/2" D
225/226 Flush Pull
• Ideal for use on sliding doors.
• Easy installation.
• Made from wrought brass.
• Conforms to design requirements of ANSI/BHMA A156.9 B22201
and A156.14 D2781.
• 225 packed with brads; 226 packed with screws.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
ED
U
N
TI
N
CO
S
I
D
Dimensions:
225 Inside Cup Diameter: 1-1/2"
225 Overall Diameter: 1-3/4"
225 Depth: 3/8"
226 Inside Cup Diameter: 2-1/8"
226 Overall Diameter: 2-1/2"
226 Depth: 7/16"
227 Flush Pull
• Contoured for ease of pulling.
• Extra deep well.
• Deluxe quality.
• Made from wrought brass.
• Conforms to design requirements of ANSI/BHMA A156.9 B22201
and A156.14 D2781.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
3-5/8" H x 1-3/4" W x 9/16" D
K6
Cabinet/Closet Knobs and Pulls
425/426 Flush Ring Pull
• Ideal for use on sliding doors.
• Convenient finger grip provides easy use of pull.
• Made from wrought brass.
• Conforms to design requirements of ANSI/BHMA A156.9 B22201.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
D
E
U
TIN
N
CO
S
I
Dimensions:
D
425 Inside Cup Diameter: 1-1/2"
425 Overall Diameter: 1-3/4"
425 Depth: 3/8"
426 Inside Cup Diameter: 2-1/8"
426 Overall Diameter: 2-1/2"
426 Depth: 3/8"
42 Pocket Sliding Door Bolt
• Exclusive Ives design permits emergency release of bolt from outside the
door.
• Spring activated design allows feather-touch action.
• Brass grommet supplied to cap release hole, protecting the door’s finish.
• Made from wrought brass.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
Overall Size, Plate: 3-1/16" x 1-5/32"
Strike: 1" x 3/4"
Depth of Mortise: 5/8"
230 Sliding Door Edge Pull
• 3/4" width allows installation on narrow as well as standard doors.
• Spring automatically returns lever flush with plate.
• Made from solid brass.
• Conforms to design requirements of ANSI/BHMA A156.14 D2801.
• Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B19, B26, B26D.
Dimensions:
3-7/8" H x 3/4" W
K7
Cabinet/Closet Knobs and Pulls
990 Sliding Door Pull
• Fits doors 1-3/8" to 1-1/2".
• Decorative coined edges.
• Pre-assembled for doors opening left to right. Plates are reversible.
• Body and strike made from solid brass.
• Finishes: B3, B5, B26, B-613, B-619, B-620.
Dimensions:
1-3/4" deep x 2-1/4" high
991 Sliding Door Lock
• Fits doors 1-3/8" to 1-1/2".
• Decorative coined edges.
• Pre-assembled for doors opening left to right. Plates are reversible.
• Body, turn knob and strike made from solid brass.
• Finishes: B3, B5, B26, B-613, B-619, B-620.
Dimensions:
1-3/4" deep x 2-1/4" high
992 Double Sided Sliding Door Lock
• Fits doors 1-3/8" to 1-1/2".
• Decorative coined edges.
• Pre-assembled for doors opening left to right. Plates are reversible.
• Body, turn knobs and strike made from solid brass.
• Finish: B3.
D
E
U
TIN
N
CO
S
I
D
Dimensions:
1-3/4" deep x 2-1/4" high
K8
Section L
Hobby Hardware
Hobby Hardware
78 Hook and Staple
• Made from solid brass
• Finish: B3
Dimensions:
Hook: 1-1/2” Long
Staple: 3/4” high x 15/16” wide
86 Hobbyist Barrel Bolt
• Made from solid brass
• Finish: B3
Dimensions:
Bolt plate: 1-9/16” high x 1-11/16” wide
Bolt guide: 1-9/16” high x 7/16” wide
Strike plate: 1-9/16” high x 5/8” wide
89 Hobbyist Padlock w/ Keys
• Made from steel
• Finish: F5
Dimensions:
Padlock, overall height: 1-5/16”
Padlock, overall width: 3/4”
D
E
U
TIN
N
CO
S
I
D
328 Friction Catch
• Made from steel
• Finish: F3
Dimensions:
Catch, overall depth: 5/8”
Catch, body depth: 1/2”
Catch, overall height: 3/8”
D
E
U
TIN
N
CO
S
I
D
420 Flush Pull Ring
• Made from solid brass
• Finish: B3
Dimensions:
Overall height: 1-3/4”
Overall width: 1-7/16”
D
E
U
TIN
N
CO
S
I
D
L1
Hobby Hardware
520 Cabinet Knob
• Made from solid brass
• Finish: B3
Dimensions:
Projection: 3/8”
Diameter: 1/2”
690 Continuous Hinge
• Made from solid brass
• Finish: B3
Dimensions:
Overall height: 4”
Overall width: 3/4”
D
E
U
TIN
N
CO
S
I
D
D
E
U
TIN
N
CO
S
I
D
691 Continuous Hinges
• Made from solid brass
• Finish: B3
Dimensions:
Overall height: 8 “
Overall width: 3/4”
D
E
U
TIN
N
CO
S
I
D
9010 Narrow Butt Hinge
9020 Narrow Butt Hinge
9030 Narrow Butt Hinge
• Made from solid brass
• Finish: B3
Dimensions:
9010 Overall height x overall width: 3/4” x 5/8”
9020 Overall height x overall width: 1” x 3/4”
9030 Overall height x overall width: 1-1/2” x 15/16”
9040 Narrow Butt Hinge
• Made from solid brass
• Finish: B3
Dimensions:
Overall height x overall width: 2” x 1”
L2
Hobby Hardware
9011 Middle Butt Hinge
9021 Middle Butt Hinge
9031 Middle Butt Hinge
• Made from solid brass
• Finish: B3
Dimensions:
9011 Overall height x overall width: 3/4” x 11/16”
9021 Overall height x overall width: 1” x 7/8”
9031 Overall height x overall width: 1-1/2” x 1”
9041 Middle Butt Hinge
9051 Middle Butt Hinge
• Made from solid brass
• Finish: B3
Dimensions:
9041 Overall height x overall width: 2” x 1-1/4”
9051 Overall height x overall width: 2-1/2” x 1-1/2”
9012 Broad Butt Hinge
9022 Broad Butt Hinge
9032 Broad Butt Hinge
D
E
U
TIN
N
O
Dimensions:
C
S
I
9012 Overall height x overall width: 3/4”
Dx 1”
9022 Overall height x overall width: 1” x 1”
• Made from solid brass
• Finish: B3. 9022 also available in B5.
9032 Overall height x overall width: 1-1/2” x 1-1/4”
9042 Broad Butt Hinge
• Made from solid brass
• Finishes: B3, B5
Dimensions:
Overall height x overall width: 2” x 1-3/8”
9033 Desk Butt Hinge
9043 Desk Butt Hinge
D
E
U
TIN
N
Dimensions:
CO
S
9033 Overall height x overall width: 1-1/2” xI2-1/16”
D
9043 Overall height x overall width: 2” x 3-1/16”
• Made from solid brass
• Finish: B3
L3
Hobby Hardware
9060 Decorative Hinge
• Made from solid brass
• Finishes: B3, B5
Dimensions:
Overall height x overall width: 5/8” x 1”
D
E
U
TIN
N
CO
S
I
D
9061 Decorative Hinge
D
E
U
TIN
N
Dimensions:
CO
Overall height x overall width: 3/4” x 1-7/8” IS
D
• Made from solid brass
• Finish: B3
9070 Decorative Hinge
• Made from steel
• Finish: F3
Dimensions:
Overall height x overall width: 1-5/16” x 2-7/8”
9071 Decorative Hinge
9072 Decorative Hinge
• Made from solid brass
• Finishes: B3, B5
Dimensions:
9071 Overall height x overall width: 1-11/16” x 3-1/16”
9072 Overall height x overall width: 1-5/16” x 2-3/16”
9073 Decorative Hinge
D
E
U
TIN
N
Dimensions:
CO
Overall height x overall width: 1-1/8” x 1-3/8” IS
D
• Made from solid brass
• Finishes: B3, B5
L4
Hobby Hardware
9080 Decorative Hinge
• Made from solid brass
• Finish: B3
Dimensions:
Overall height x overall width: 5/8” x 2-3/4”
UED
N
I
NT
O
C
DIS
9081 Decorative Hinge
• Made from solid brass
• Finish: B3
Dimensions:
Overall height x overall width: 5/8” x 1-7/8”
ED
U
N
NTI
O
C
DIS
9090 Decorative Hinge
• Made from solid brass
• Finish: B5
Dimensions:
Overall height x overall width: 2” x 1-3/8”
9110 Decorative Hasp
• Made from solid brass
• Finishes: B3, B5
Dimensions:
Overall height x overall width: 5/8” x 1-7/8”
9120 Hasp
• Made from solid brass
• Finishes: B3, B5
Dimensions:
Overall height x overall width: 3/4” x 2-3/4”
9121 Hasp
9122 Hasp
• 9121 made from solid brass
• 9122 made from steel
• Finishes: 9121 in B3, 9122 in F3
Dimensions:
9121 Overall height x width: 1” x 2-7/8”
9122 Overall height x width: 1-1/4” x 3-1/8”
ED
U
N
NTI
O
C
DIS
L5
Hobby Hardware
9130 Hasp with Hook
• Made from solid brass
• Finish: B3
Dimensions
Overall height x overall width: 3/4” x 2-3/4”
9210 Support Hinge
• Made from steel
• Finish: F3
• Handed. Specify Left Hand (LH) or Right Hand (RH)
Dimensions
Extension: approx. 10-3/8”
9220 Friction Lid Support
• Made from steel
• Finish: F3
• Handed. Specify Left Hand (LH) or Right Hand (RH)
Dimensions
Extension: approx. 5”
9230 Friction Lid Support
• Made from steel
• Finish: F3
• Right Handed (RH)
Dimensions
Extension: approx. 5-1/2”
D
E
U
TIN
N
CO
S
I
D
9240 Lid Support
• Made from steel
• Finish: F19
• Specify Left Hand (LH), Right Hand (RH), Center (CTR)
Dimensions
Extension: approx. 6”
L6
D
E
U
TIN
N
CO
S
I
D
Hobby Hardware
9250 Drop Leaf Support
• Made from steel
• Finish: F19
Dimensions
Extension: approx. 10”
9310 Decorative Corner
• Made from steel
• Finish: F3
Dimensions:
Side to corner: 1-1/2”
ED
U
N
NTI
O
C
DIS
UED
N
I
NT
O
C
DIS
9311 Decorative Corner
9312 Decorative Corner
• Made from solid brass
• Finish: B3
Dimensions:
9311 Side to corner: 1-3/4”
9312 Side to corner: 1-1/4”
9320 Bracket
• Made from solid brass
• Finish: B3
Dimensions:
Each leaf 1/2” x 1-1/8”
9321 Bracket
• Made from solid brass
• Finish: B3
Dimensions:
Each leaf 1/2” x 1-9/16”
9330 Draw Catch
• Made from steel
• Finish: F3
Dimensions:
Overall height: 1-1/2”
Overall width: 2-3/4”
L7
Hobby Hardware
9331 Draw Catch
• Made from steel
• Finish: F3
Dimensions:
Overall height: 1-3/4”
Overall width: 3-1/4”
UED
N
I
NT
O
C
DIS
9332 Draw Catch
• Made from steel
• Finish: F2C
Dimensions:
Overall height: 1-5/8”
Overall width: 2-3/8”
UED
N
I
NT
O
C
DIS
9333 Draw Catch
• Made from steel
• Finish: F2C
Dimensions:
Overall width: 3-11/16”
ED
U
N
NTI
O
C
DIS
9334 Snap Catch
• Made from steel
• Finish: F5
Dimensions:
Overall height: 1-3/8”
Overall width: 15/16”
UED
N
I
NT
O
C
DIS
9335 Catch
• Made from solid brass
• Finishes: B3, B5
Dimensions:
Overall height: 7/8”
Overall width: 1-5/16”
9340 Chest Handle
• Made from steel
• Finish: F3
Dimensions:
Overall height: 1-1/2”
Overall width: 3-1/2”
L8
UED
N
I
NT
O
C
DIS
IVES Customer Service:
1-877-613-8766
1-877-424-8494 FAX
DIVISION
8
©2003 Ingersoll-Rand
Form IV-2001C
Rev. 4/03
Printed in USA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement