User manual | CTL-DCM

CTL-DCM
Manual
2012 CASA
http://www.casa-laserlight.com
General instructions
Troubleshooting
Unpacking
If the power supply indicator doesn't light up and the laser doesn't work, please check the
power supply and the input voltage.
We will soon lead you into new sense of vision realm a life from now on!
In Stand-Alone operation, if the power supply indicator is light up and sound active
Thank you for purchasing this product.Please read user guide for safety and operations infor-
indicator isn't light up, but the laser is shut off doesn't work.
mation before using the product. Keep this manual for future reference. This product can create
A. Because sound is too small make for laser shut off in sound active, please increase
perfect laser programs and effects since it has passed a series of strictly tests before delivery.
the music volume or increase audio sensitivity with sensitivity knob, please check as below
Please check the attachments listed on the page after opening the carton. In the event of carton
B. Please check if unit has been set up in slave mode, then set up in master mode.
damage or attachment missing in transit, please contact your dealer or our after sales service
In Master-Slave operation, slave unit don't function, please check as below.
department.
A. Make sure to there's only one master in the chain, and the others are set in slave mode.
Attachments
B. Make sure to control the unit without DMX console controlling.
1. Laser Light:1PCS
C. Make sure to take a good quality power cable and connection.
Notice
2. Power Cable:1PCS
3. User Guide:1PCS
In DMX mode operation, the laser is OFF and the DMX signal indicator is unlighted,
Do not turn on and off the unit frequently.
please check as below.
Do not exposure the human eye direct to laser beam.
A. Make sure to set up the DMX mode.
Before using this unit make sure the power supply is ground.
B. Make sure to have a good connection.
This unit is intended for indoor use only and should be prevented form water, moisture
In DMX operation, the unit can’t be controlled by the DMX console, but the DMX signal
and shake. The working temperature of this unit is 18～30℃, do not use this continuously
indicator is flashing, please make sure the DMX console and unit have the same channel.
over 3 hours, otherwise it shortens the lifetime of the unit.
If the output beam direction above isn't the right way, please restart the unit.
Use cleaning tissue to remove the dust absorbed on the external lenses periodically to opt-
If the unit is fail, please turn off the unit, then turn on again after 5 minutes.
imize light output.
Do not remove or break the warranty label, otherwise it void the warranty.
After trying the above solution you still have a problem, please contact your dealer or
our company for service.
Always replace with the exact same type fuse, replacement with anything other than the
specified fuse can cause fire or electric shock and damage your unit, and will void your
manufactures warranty.
This lamp laser dangerous grade is a Class III B, eyes directly in observation in danger inside the light beam, the minimum irradiation is apart from 15
The AC110V/220V switch please don't turn without authorization, because the user turns
to result in the machine damage by oneself, our company is all irresponsible.
8
1
Features
Various working modes
……
Includes four working modes as DMX, Sound Active, AUTO and Master-Slave Control
for different applications.
Various programs
POWER
The double tunnel laser beam is compages, more than 50 laser patterns, over 200 laser eff-
1: Master: Sound/AUTO
2：Slave
N：Slave
ects.Different working modes has different program.
DMX control
The unit has 7 channels to control in DMX mode. The unit has BLACK OUT function.
Universal DMX Operation (DMX mode)
The uint will shut OFF if no DMX512 signal.
Master-Slave function
The system allow link many units (as slave unit) together to doing synchro job without co-
This mode allows you to use universal DMX-512 console to operate.
nsole in sound active or AUTO mode.
LED indicating and shut-off function
Install the units in a suitable position (laying or appending).
In sound active mode, the unit's panel has LED indicating for sound active. The unit will
Use standard XLR microphone cable chain your units together via the XLR connector on
shut off after 8 seconds when the music stops.
on the rear of the units. For longer cable runs we suggest a terminator at the last fixture.
DPSS Laser
Assign a DMX address to each the unit using dipswitches, see the "DMX Address Quick
Use Diode-Pumped Solid State green laser, stable output and long working life.
Reference Char".
Turn on the all units' power, the units begins reset, then the unit begins working.
Technical Specification
Use DMX console to control your units.
Voltage: □AC220V/ □110V, 50/60HZ, Fuse: 2A/250V
Rated Power: 30W
……
Laser
CTL-DG5: 25+25mW(green 532nm)
CTL-DG10: 50+50mW(green 532nm)
DMX Signal
1: DMX Mode
CTL-DC+:Laser Power:30mW Green + 100mW Red + 130mW Yellow + 100mW Violet
POWER
2：DMX Mode
N：DMX Mode
CTL-DCP:25+25mW green laser 532nm,80+80+80mW red laser 650nm
Working Modes: DMX, Sound Active, AUTO, Master-Slave
DMX Control Channel: 7 channels
Notes
Graphics & Effects: more than 100 patterns, over 300 effects
DMX console can not be used in Master-Slave operation (Sound Active or AUTO mode ).
Interface: 3 pins XLR jack for DMX or Maser-Slave linking
There should be only one master unit in Master-Slave operation.
Size
L*W*H=630*225*160mm
Weight:
6.5Kg
2
7
Function setting
7
2
5
4
8
6
2
Uses dipswitches to assign a unit’s function: DMX/slave, or sound active, or AUTO
mode.For the unit is DMX mode, set the DMX address. Each dipswitch represents a
binary value. See the “Function chart”.
1
3
Rear Panel Figure
Function Chart
1. Power Jack
2. Cooling Fan
Dipswitch #10 is use to set master or slave mode. Master modes have sound active and
3. Audio Sensitivity Knob
4. DMX Signal Indicator: Green
AUTO mode.Slave modes have DMX and Slave mode. The units automatically identify
5. Dipswitches: Function Setting
6. DMX or Linking Jack
DMX or SLAVE mode by data receives. Dipswitch #9 use to is set sound active or AUTO
7. ON/OFF
8. Sound Active Microphone/ Power Indicator
mode in master mode.
DMX address calculation
Operation
For DMX mode, DMX512 address from #1 to 9# dipswitches must be set, the
address is set from 1 to 511. Each dipswitch represents a binary value.
Master-Slave Operation
This mode will allow you to link up to 32 units together without controller.
Dipswitch
Value
Dipswitch
Value
＃1
1
＃6
32
＃2
2
＃7
64
＃3
4
＃8
128
Install the units in a suitable position (laying or appending).
＃4
8
＃9
256
Turn on the all units' power, the units begins reset, then the unit begins working. The slave
＃5
16
＃10
Set to "0"
units will react the same as the master unit.
One unit has 7 channels, so each unit must be assigns 7 channels at least. We may
Choose a unit to function as Master mode, set dipswitch to select Sound Active or AUTO
assign 8 channels for one unit, then DMX address = 8*N + 1, N=0, 1, 2, 3 ……
mode. The others must be set to Slave mode, set dipswitch to select Slave mode.
Example
Use standard XLR microphone cable chain your units together via the XLR connector on
One loop address=1, two loop address=9, three loop address=17, four loop address=25
Loop
the rear of the units. For longer cable runs we suggest a terminator at the last fixture.
Address
Binary
Dipswitches
The units will react to the low frequencies of music via the internal microphone. Adjust the
1
1
100000000
＃1
audio sensitivity knob on the back of the master unit to make the unit more or less sensi-
2
9
100100000
＃1+#4
tive in sound active.The panel has LED indicating for sound active.
6
3
17
100010000
＃1+#5
4
25
100110000
＃1+#4+#5
3
DMX Control
DMX Control Parameter Chart
Channel
CH1
Function
Mode
Value
Description
0～49
Close, laser OFF
50～99
Sound active mode
175～179
ve-flex dot line square extend
50～54
135° diagonal scan circle extend
180～184
ladder line 1
dot square extend
55～59
dot diagonal
circle jump
185～189
ladder line 2
rectangle turn
60～64
V line 1
dot circle jump
190～194
ladder line 3
dot rectangle turn
65～69
V dot line 1
hori-line jump
195～199
ladder line 4
square turn
70～74
V line 2
hori-dot line jump
200～204
tetragon 1
dot square turn
75～79
V dot line 2
vertical line jump
205～209
tetragon 2
pentagon turn
80～84
triangle 1
ver-dot line jump
210～214
pentagon 1
dot pentagon turn
dot triangle 1
diagonal jump
215～219
pentagon 2
tetragon turn
150～199 Static patterns of DMX mode
90～94
triangle 2
dot diagonal jump
220～224
pentagon 3
pentagon star turn
95～99
dot triangle 2
short sector round 1
225～229
pentagon 4
bird fly
52 static/dynamic patterns
100～104
square
short sector round 2
230～234
wave line
dot bird fly
0～255
Adjust position-X
105～109
dot square
long sector round 1
235～239
wave dot line
wave flowing
Position-Y
0～255
Adjust position-Y
110～114
rectangle 1
long sector round 2
Scanning speed
0～255
0 is speedy, 255 is slow
115～119
dot rectangle 1 line scan
0 is speedy, 255 is slow, has ten
120～124
rectangle 2
grade speed
125～129
dot rectangle 2 45° diagonal move
Pattern selection
CH3
Position-X
CH4
CH5
Dynamic pattens
0～255
play speed
CH7
dot circle to add
85～89
0～255
CH6
dot diagonal
100～149 AUTO mode
200～255 Dynamic patterns of DMX mode
CH2
45～49
Static pattern size
0～255
dot line scan
240～244
spirality line
dot wave flowing
245～249
many dot 1
many dot jump 1
250～254
many dot 2
square dot jump
255
square dot
many dot jump 2
0 is small, 255 is big
There are 52 static patterns, the sizes of the patterns that DMX value is 140 previous are
CH2 Parameter Chart For Function
DMX value Static patterns Dynamic patterns
adjustable,the following irregular patterns are non-adjustable. There are 52 dynamic patterDMX value Static patterns Dynamic patterns
0～4
circle
circle to big
130～134
christcross
dot diagonal move
5～9
dot circle 1
dot circle to big
135～139
chiasma line
hori line flex
10～14
dot circle 1
scan circle to big
140～144
hor-extend line hori dot line flex
15～19
scan circle
circle flash
145～149
hori-shrink line hori line move
20～24
horizontal line dot circle flash
150～154
hori-flex line
25～29
hori-dot line
circle roll
155～159
ho-flex dot line vertical line move
30～34
vertical line
dot circle roll
160～164
ver-extend line vert-dot line move
35～39
vert-dot line
circle turn
165～169
vert-shrink line rectangle extend
40～44
45° diagonal
dot circle turn
170～174
vert-flex line
ns, whose sizes are non-adjustable.
Front/Rear Panel
1
1
1
1
hori dot line move
dot rectangle extend
1、Laser Aperture One
Front Panel Figure
4
5

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project