null  User manual
CI2070
Five Band
Adjustable Gain In-Building
Smart Technology ™
Signal Booster - 70/75 dB
(w/F-Connectors)
Contents:
Antenna Options & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick Install Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Finding the Strongest Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Outside Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Inside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing a Wilson Electronics Signal Booster. . . . . . . . . . . . . . . . . . . . . 9
Powering up a Wilson Electronics Signal Booster . . . . . . . . . . . . . . . . . 10
Button Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Understanding LCD Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Warnings and Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Guarantee, Warranty & Specifications . . . . . . . . . . . . . . . . . Back Cover
Appearance of device and accessories may vary.
Note: This manual contains important safety and operating information. Please read and follow the
instructions in this manual. Failure to do so could be hazardous and result in damage to your Signal
Booster.
Installation Instructions for the Following Wilson
Electronic Signal Booster:
CI2070 Five Band Adjustable Gain In-Building
Smart Technology ™ Signal Booster - 70/75 dB (w/F-Connectors)
Model #273470 FCC: PWO273470
How it Works
Wilson Electronics Signal Boosters are bi-directional devices that deliver service
levels consistent with what would be expected in areas of high cell network coverage.
They amplify a weak or shadowed signal in mobile (marine, RV, vehicles) and
in-building (home, office,machine to machine) applications. When using a Wilson
Electronics Signal Booster in conjunction with Wilson Electronics antennas, the
Outside Antenna will collect the cell tower signal and send it through the cable to
the Signal Booster. The signal is then amplified and re-transmitted through the
Inside Antenna into the room. Cell phones and cellular data cards in that area
then communicate with the improved signal. When a cell phone or cellular device
transmits, the signal is received by the Inside Antenna, amplified by the Signal
Booster and transmitted back to the cell tower through the Outside Antenna.
Inside this Package
Note: Kits may contain different accessories
AC/DC
Power Supply
12V / 3A
Signal
Booster
(859900)
Outdoor Antenna Options & Accessories
1. Wide Band Directional Antenna 700 - 2700 MHz
(304475 – 75 Ohm Wide Band) Note: The Outside
fixed Antenna must be connected with a minimum of
26’ of RG58 coax cable (950630).
2. Pole Mount Wide Band Panel Antenna (304473)
1
Indoor Antenna Options & Accessories
A. Wide-Band Panel Antenna 700-2700 MHz
(multiple mounting options available)
B. 75 Ohm Lightning Surge Protector N Connector
(859992)
Splitter options on page 9
2
A
B
Appearance of device and accessories may vary.
To purchase, call Wilson Electronics Sales Department at: 800-204-4104
We recommend using directional antennas with this Signal Booster.
1
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Quick Install Overview
See Installation Diagram on page 3 & 4. Contact Wilson Electronics Technical
Support Team with any questions at 866-294-1660.
1. Select a location on the roof or outside of the building to install the Outside
Antenna. Use a Wilson Electronics Signal Detector, P/N 867501 or a cell phone
which has been placed in test mode to locate the strongest signal from the
cell tower. Refer to page 7. Visit www.WilsonElectronics.com to find test mode
instructions for your particular cell phone. Make sure the Outside Antenna is
positioned on the side of the building with the strongest cell signal, and is
pointing away from the building.
2. Select a location to install the Signal Booster that is away from excessive heat,
direct sunlight or moisture, and has adequate ventilation. Airtight enclosures
are not recommended. Choose a location as close to the outside antenna as
possible in order to minimize cable length. This will reduce signal attenuation to
the amplifier due to cable loss.
3. Connect the cable from the Outside Antenna to the Signal Booster’s “Outside
Antenna” connector. Refer to page 8 for more information on running cable.
Lightning Surge Protection is recommended for all in-building installations. Refer
to page 7.
4. Select a location for the Inside Antenna. Try to choose a position in the center
of the area needing improved signal. Keep in mind that proper antenna
isolation is necessary for the system to function properly. This may require as
much as 50 to 75 feet of horizontal separation from the Outside Antenna.
Vertical separation helps increase isolation. Alternate means of isolation
are possible. If physical separation is not possible, please contact Wilson
Electronics Tech Support at 866-294-1660 for suggestions on alternate
methods to achieve isolation.
5. Connect the cable from the Inside Antenna to the Signal Booster’s “Inside
Antenna” connector. Refer to page 8 for more information on running cable.
Keep cable runs as short as possible to reduce loss in the system.
6. Before powering up the Signal Booster, verify that both the Outside Antenna
and the Inside Antenna are connected correctly, and check that all connections
are tight. Refer to page 9. Note: Be careful when plugging the connectors in so
as not to bend the center pins on the connectors.
7. Power on the Signal Booster by plugging in the included power supply. If the
lights are not green, please refer to pages 10-13.
IMPORTANT NOTICE • It is very important to power your Signal Booster using a surge protected AC Power Strip
with at least a 1000 Joule rating.
• Failure to do this will void your warranty in the event of a power surge or lightning strike.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
2
Installation Diagram
Outside Antenna
(Wide Band Directional
(W
Antenna shown)
An
Inside Antenna
Preferred Method: Place the Inside
Antenna in the ceiling facing down for
the best coverage.
Note: The Inside Antenna may be
mounted on the wall directly under the
Outside Antenna, in the null zone, if
20 feet of vertical separation can be
maintained.
Null Zone: The area under the
Outside Antenna, where the
Outside Antenna radiates the
least.
Note: A Lightning Surge Protector is
recommended for all building installations
(sold separately). Make sure the protector
is installed in line between the Outside
Antenna and the Signal Booster.
Inside Antenna
(Optional
second
antenna for
additional
coverage).
Power
Supply
Typical Installation
3
Contact Wilson Electronics Technical Support Team
am with any questions at 866-294-1660
or email: [email protected] Mon.- Fri.
F i Hours:
H
7 am to
t 6 pm MST.
MST
Before Getting Started
This guide will help you properly install your Wilson Electronics Signal Booster. It
is important to read through all of the installation steps for your particular
application prior to installing any equipment. Read through the instructions,
visualize where all the equipment will need to be installed and do a soft
installation before mounting any equipment. Contact Wilson Electronics Technical
Support with any questions at: 866-294-1660.
Splitter (2-way or 3-way
if using multiple inside
antennas)
Lightning
Surge Protector
(recommended)
Inside Antenna
(Optional
third antenna
for additional
coverage)
Signal
Booster
Surge Protector
Power Strip
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
866-294
294-1660
or email:
il [email protected]
t [email protected] il
l t i
Mon.M
Fri.
F i Hours:
H
7 am tto 6 pm M
MST.
ST
4
Reasons for Weak Cellular Signals
Anyone who uses a cell phone or cellular data card knows the frustration of not
being able to connect to or maintain a strong cellular signal. When this occurs, it is
generally due to one of two reasons:
1. Location of the Nearest Cell Tower – Cell towers are situated to provide broad
coverage; however, there are many areas in which signal strength may be
reduced by topographic features or by local government restrictions on the
height or placement of the towers themselves. Rural areas generally have
fewer cell towers than urban regions.
2. Natural and Man-Made Obstructions – Signal strength can also be negatively
affected by trees, hills, buildings, weather, and other obstructions. You may be
relatively close to a cell tower but still unable to make a call. This often occurs
in homes, offices and other buildings in which stucco, concrete or metal walls
may block the signal.
The Signal Booster works with two antennas. The Inside Antenna communicates
with your cell phone and the Outside Antenna communicates with the cell tower.
The Outside Antenna receives the cell tower signal and sends it through the cable
to the Signal Booster, where it is amplified and transmitted through the Inside
Antenna into the room. When the Inside Antenna picks up a signal from your
cellular device, the Signal Booster amplifies that signal and transmits it through
the cable, then through the Outside Antenna and back to the cell tower.
Note: The Signal Booster will only operate if there is an adequate signal to amplify.
Wide Band Antenna
Cell Tower
Selecting a Direction for the Outside Antenna
Use a cell phone in test mode to find the strongest signal from the cell tower
(refer to page 7 for more information). To get the strongest signal possible, it
is very important to set up your Outside Antenna properly. The Inside and the
Outside Antenna must be mounted in such a way that they are able to pick up
the best possible cell signal on the outside of the building and provide the best
possible signal on the inside of the building. Mount the Outside Antenna as
5
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
high as possible facing the cell tower in an area with the best possible signal
coverage.
Note: Never point the front of a directional antenna toward the Inside Antenna.
Finding the Strongest Signal
When installing your Signal Booster’s Outside Antenna, aiming it towards
the best signal source from you service provider is important. The best way
of getting the strongest signal is to have one person on the roof to rotate the
Outside Antenna, which is connected to the Signal Booster. Turn the Outside
Antenna about 45 degrees at a time, while the second person is watching the
signal strength on the phone inside the building. This allows you to read the
signal strength from the cell tower. It is preferable to have the phone in the
test mode so the actual signal strength can be read, as bars are not the most
accurate. Go to www.WilsonElectronics.com for help in finding the test mode for
your phone. Always make sure the person inside the building gives the signal
time to arrive and register on the phone (between 10-30 seconds for phone to
reset to the signal reading).
Cell Signal
Outside
Panel
Antenna
Cell Tower
Signal readings usually appear as a negative number (for example, -86). The
closer you get to zero the stronger the signal. (See graph below).
Signal Strength Graph
EXCELLENT
-50dB
-60dB
GOOD
-70dB
-80dB
POOR
-90dB
-100dB
NO
SIGNAL
-110dB
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
6
Outside Antenna Installation
The antenna should be mounted as shown in the illustration on page 5. The
mounting bracket, included with antenna, is adjustable and will accommodate
pipe diameters from 1.25 inches to 2 inches (pipe sold separately #901117).
Mount the antenna so that there is at least 3 feet of clearance in all directions
around it. Position the antenna so that it has an unobstructed line of sight to the
cell tower’s strongest signal. Make sure the antenna is not pointing across your
own roof or at the Inside Antenna as this will cause the oscillation protection
circuitry to shut down the Signal Booster.
Warning: The Outside fixed Antenna must be connected with a minimum of
26 feet of RG58 coax cable.
Warning: Lightning protection is recommended for all installations
(#859992-75 Ohm shown below). Take extreme care to ensure
that neither you nor the antenna comes near any electric power
lines.
Installing Lightning Protection (sold separately)
Install the Lightning Surge Protector
(LSP) close to the Signal Booster. Attach
the cable from the Outside Antenna to
the surge protector, using a short length
Lightning
of low loss cable; attach one end to the
LSP and the other to the Outside Antenna Surge Protector
(sold separately)
connector on the Signal Booster. Ensure
the LSP is properly grounded (ground
(not included)
wire not included). LSP sold separately,
go to www.WilsonElectronics.com or call
To Inside
800-204-4104 to order.
To Outside
Antenna
Ground Wire
(not included)
To Signal
Booster
Antenna
Signal Booster
Surge Protector Power Strip
7
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Mounting Tips for Running Outside Antenna Cable
If you are mounting the Outside Antenna on the roof of your building, we have
found that it is easiest to run your cable underneath the down side of your roof’s
flashing. If you have satellite TV service installed you may be able to follow the
same route as the satellite TV cables that are already running from outside of your
building to the inside.
After routing the cable, we recommend sealing any areas where the cable passes
into the building with cable bushings, silicone or a silicone-type sealant to keep
your installation from leaking. If you are mounting the Outside Antenna to the
outside wall of your home or building, the simplest way is to run the cable on the
outside of the wall and attach it to the exterior of your home or office. Then drill
a hole through the wall where you want the cable to appear on the inside of the
building. Before drilling, make sure that there are no electrical outlets, sewer or
water pipes, or electrical wiring in the wall that you are about to drill through as this
could potentially harm you or damage the building.
After drilling the required hole, run the cable through and seal it with cable
bushings or a silicone-type sealant to enclose the hole that you have created. In
some instances, it may be possible to run the cable up into the fascia of the attic
overhang. In this circumstance, the cable will be accessible in the attic for further
routing.
Installing the Inside Antenna
(Instructions are for optional Inside Panel Antenna)
Select a location for the Inside Antenna, preferably in the center of where the
signal needs to be amplified. A minimum separation distance of 20 vertical feet
(within the null zone) or 50 horizontal feet is necessary for proper operation.
If the inside coverage is not sufficient you may need as much as 75 feet of
horizontal separation. Refer to installation diagram on pages 3 & 4.
Inside
Antenna
Ceiling
Rafters
Ceiling
Drywall
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
8
In some cases, multiple Inside Antennas may be required, for instance if you
have multiple rooms with poor signal. A signal may be split by using a splitter
(sold separately). Refer to the configuration on pages 3 & 4.
Optional Wide Band
Inside Antenna
(sold separately)
Multiple mounting
options available
Splitter Options:
3-way
3(859994)
(8
2
2-way
(859993)
Installing a Wilson Electronics Signal Booster
Select a location to install the Signal Booster that is away from excessive heat,
direct sunlight, moisture and that has proper ventilation. Do not place the Signal
Booster in an air-tight enclosure. Recommended installation locations for In-Building
Signal Boosters are near a power outlet and in a closet or on a shelf.
Note: It is important to have adequate air ventilation. Maintain at least 6 inches
of clearance from surrounding objects. Be careful when plugging the
connector in so as not to damage the center pins on the connectors.
Run the Outside Antenna cable to the Signal Booster and attach it to the
connector labeled “Outside Antenna” on the Signal Booster. Run the Inside
Antenna cable to the Signal Booster and attach it to the connector labeled “Inside
Antenna” on the Signal Booster.
Note: For distances of 20 feet or more, use Wilson low loss cable.
Note: It is very important to power your Signal Booster using a surge protected AC
Power Strip with at least a 1000 Joule rating. Failure to do this will void your
warranty in the event of a power surge or lightning strike.
Warning: An Inside Antenna must have a separation distance from all persons
that is at least 8 inches for the Panel Antenna.
9
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
CORRECT INSTALLATION
Point antennas away from each other
Inside Panel
Antenna
Outdoor
Antenna
Signal Booster
Figure 1
INCORRECT INSTALLATION
Never point antennas toward each other
Inside Panel
Antenna
Outdoor
Antenna
Signal Booster
Figure 2
Powering up a Wilson Electronics
Signal Booster
1. Never point the front of a directional Outside Antenna toward the Inside
Antenna. Refer to Figures 1 & 2 above.
2. Ensure that both the Outside Antenna cable and the Inside Antenna cable
are connected to the Signal Booster and the connections are tight before
powering up the Signal Booster.
3. Plug the power supply into the Signal Booster input marked “POWER”
(carefully, to avoid damaging the center pin) and then into a surge protected
AC Power Strip.
4. Using multiple Signal Boosters in one installation could cause interference to
the cell tower.
5. Contact Wilson Electronics Technical Support Team with any questions at
866-294-1660 or email [email protected] Technical Support hours
are Mon.- Fri. 7 am to 6 pm MST.
Button Operation 1
1 FACTORY RESET – Pushing and holding the “Reset” button for 5 seconds will
reset the Signal Booster to max gains.
Note: If the Signal Booster is unplugged, the Manual Gains will remain the same
as they were before being unplugged.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
10
2 BAND SELECT – Pressing the “Band Select” button will cycle through the
bands.
3 UP – Adjusts the Manual Gain Control (MGC).
a. Pressing the “UP” (refer to Figure 3) button will cause the selected gain to
increase in 1dB increments (MGC will be displayed on LCD screen).
b. Gains will never go higher than the maximum (70dB or 75dB).
c. Holding the “UP” button on the initial plug-in will turn all of the manual gains to
maximum (70 dB or 75 dB) to aid the installer during setup.
Figure 3
3
PUSHUpUP
GAIN
4
OVERLOAD
GAIN
62 AA’ 72
PUSHDown
DOWN
Band
Band
Select PUSH
Select
Reset PUSH
Reset
2
1
4 DOWN – Adjusts the Manual Gain Control (MGC).
a. Pressing the “DOWN” (refer to Figure 3) button will cause the selected gain to
decrease in 1dB increments (MGC will be displayed on LCD screen).
b. Gains will never go lower than the minimum (40 dB or 45 dB).
c. Holding the “DOWN” button on the initial plug-in will turn all of the manual
gains to minimum (40dB or 45dB) to aid the installer during setup.
Understanding the LCD Screen
1. Four Bands can be individually selected:
a 700 Bands 12 / 17, 13 (LTE)
A700
B12 (AT&T) = Band 12 / 17 (LTE)
B13 (Verizon) = Band 13 (LTE)
b 800 – Band 5 (AMPS)
A800
11
c 1900 – Band 2 (PCS)
APCS
AOK
d 1700/2100 – Band 4
(AWS)
AAWS
AOK
AOK
AOK
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
2. Press the Band Select button to scroll through all bands to verify that they are
functioning properly. You may need to do this several times to eliminate all
“OVL-OFF” and/or “OSC” situations. Asterisks will only flash if one or more
Bands have been turned off due to overload or
oscillation. Find the Bands that have turned off
by pressing the “BAND SELECT” button. The
Asterisks will not flash if any or all Bands have
automatically reduced Gain due to receiver
overload.
S
OVL
Figure 4
3. When a band is selected by using the “Band
Select” button, Manual Gains can be changed
from a maximum of 70dB / 75dB to a minimum
of 40dB / 45dB by using the UP and DOWN
buttons (MGC will be displayed).
S
OSC
4. “OVL”
a An “OVL” in the bottom-right corner of
the LCD screen of the frequency that is
Figure 5
receiving an overload signal (refer to Figure
4) indicates that the selected frequency has
been reduced due to receiver overload. This
reduction is to prevent the disruption of cell towers. The “Band Select” button
must be pressed to cycle through the frequencies to display the Band that
has the overload. There is no need to reduce the Gain manually, this is done
automatically and will be displayed on the LCD screen. You can manually
decrease the Gain, but cannot increase higher than what the AGC (Automatic
Gain Control) has set. If reduced Gain is desired, press the “DOWN” button
to decrease the gain until you have an “OK” on the bottom-right corner of the
LCD screen. The Signal Booster is now working with reduced Gain. More
than one frequency can overload at the same time. If one Band is reduced
and an OVERLOAD exists on another Band, press the “Band Select” to
display the Band that is experiencing overload. Contact Wilson Electronics
Technical Support Team for assistance: 866-294-1660.
b An ORANGE light indicates that the selected frequency has turned off due to
receiver overload. “OVL” and “OFF” will flash in the bottom right of the LCD
screen. This is due to the close proximity of a cell tower, the Outside Antenna
should be turned to reduce the signal strength to and from the cell tower.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
12
5. A RED light and a flashing “OSC” and “OFF” in the bottom-right corner of the
LCD screen (refer to Figure 5) indicates that the selected frequency has shut
down to prevent an oscillation, most likely caused by the Inside and Outside
Antennas being physically too close to each other. Without this patented
protection, oscillations could be transmitted to the cell tower, blocking calls to and
from the cell tower. Oscillation occurs just like in an audio system when you put a
microphone next to a speaker and get a big squeal. When the Inside Antenna is
too close to the Outside Antenna, the same type of oscillation occurs.
During an oscillation, the Signal Booster will turn off all of the frequencies that
were found to oscillate. If the Signal Booster has a red light and flashing “OSC”
and “OFF” is displayed in the bottom-right corner, the following procedures need
to be done:
a To check your cables and connections, unplug the power cord, then
remove the coax cables from the two connectors of the Signal Booster.
Hold the “Down” button and plug in the Signal Booster. This will adjust
Gains to minimum. You should now have a green light (if not, call Wilson
Electronics Technical Support). When the green light is achieved, unplug the
power supply, reconnect the coax cables to the Signal Booster, tighten all
connections and plug the power supply back in.
b From minimum gain (40 / 45 dB) increase the gain on each frequency by
pressing the “UP” button until you get a red light, then press the “DOWN”
button 1-2 times to achieve a green light (for example, it may be at 50 dB
for the red light). If your coverage area is low, the Outside Antenna needs to
be pointed at the cell tower with its back to the Inside Antenna. The Inside
Antenna needs to have its back facing the back of the Outside Antenna (the
Wilson Logo indicates the front of the antenna). Without proper orientation
of the antennas, you will not be able to get maximum gain from the Signal
Booster. You may need to separate the antennas further apart to get the
necessary gain* for the system to give maximum coverage and a green light.
The lower the gain the less coverage area you will have.
*Note: If the antennas cannot be sufficiently separated, the Signal Booster will
have to operate with reduced performance by decreasing the gain(s) until a
green light (OK on the LCD screen) is obtained.
6. Asterisks will flash on the LCD screen if at least one Band has been turned off
due to receiver overload or oscillation. Select the Bands that have turned off by
pressing the “Band Select” button.
13
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Warnings and Recommendations
Warning: The Outside Antenna must always be located so the back or side
points to the Inside Antenna. Never point the front of the Outside
Antenna toward the Inside Antenna – this is to prevent oscillation.
Warning: Connecting the Signal Booster directly to the cell phone with use of
an adapter will damage the cell phone and/or Signal Booster.
Warning: Use only the correct Wilson Electronics power supply. Use of a
non-Wilson Electronics product may damage your equipment.
Warning: RF Safety: All inside antennas used with this Signal Booster
may not have gain (less cable loss) that exceeds 10.1 dBi and
must be located at least 8 inches from all people. Outside fixed
antennas may not have gain that exceeds 2.8 dBi (less cable loss)
and must be located least 27 inches from all people. The outside
fixed antenna must be connected with a minimum of 26 feet of
RG58 coaxial cable. All antennas shown on page 1 meet these
requirements.
Warning: Verify that both the Outside Antenna and the Inside Antenna are
connected to the Signal Booster before powering up the Signal
Booster.
Recommendation: Omni Directional Antennas are not recommended with this
Signal Booster.
Recommendation: Lightning Surge Protection is recommended for all inbuilding installations.
This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. Changes or modifications not expressly approved by Wilson Electronics could void the authority to operate this
equipment.
About Wilson Electronics
Wilson Electronics, LLC has been a leader in the wireless communications industry for over 40 years. The company designs
and manufactures Signal Boosters, antennas and related components that significantly improve cellular telephone signal
reception and transmission in a wide variety of applications, mobile (marine, RV, vehicles) and in-building (home, office,
machine to machine).
With extensive experience in antenna and Signal Booster research and design, the company’s engineering team uses a
state-of-the-art testing laboratory, including an anechoic chamber and network analyzers, to fine-tune antenna designs and
performance. For its Signal Boosters, Wilson Electronics uses a double electrically shielded RF enclosure and cell tower
simulators for compliance testing.
Wilson Electronics Signal Boosters feature patented Smart Technology ™ that enables them to automatically adjust their
power based on cell tower requirements. By detecting and preventing oscillation (feedback), signal overload and interference
with other users, these Smart Technology ™ Signal Boosters improve network cell phone areas without compromising carrier
systems.
All products are engineered and assembled in the company’s 100,000 square-foot headquarters in St. George, Utah. Wilson
Electronics has product dealers in all 50 states as well as in countries around the world.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
14
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason
the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of
purchase.
2-Year Warranty
Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials.
Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of
purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics
shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced
product back to the original consumer if located within the continental U.S.
This warranty does not apply to any Signal Booster determined by Wilson Electronics to have been subjected to
misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.
Disclaimer : The information provided by Wilson Electronics, LLC is believed to be complete and accurate.
However, no responsibility is assumed by Wilson Electronics, LLC for any business or personal losses arising from
its use, or for any infringements of patents or other rights of third parties that may result from its use.
Copyright © 2013 Wilson Electronics, LLC All rights reserved.
U.S. Patent Nos. – 7,221,967; 7,729,669; 7,486,929; 7,409,186; 7,783,318; 7,729,656
Signal Booster Specifications
CI2070
Model Number
273470
Antenna connectors
F-Female
Antenna Impedance
75 Ohms
Dimensions
8.875 x 6.0 x 1.5 inch (22.5 x 15.2 x 3.8 cm)
Weight
2.8 lbs (1.270 kg)
Frequency
3
698-746 MHz / 746-787 MHz / 824-894 MHz / 1850-1990 MHz / 1710-2155 MHz
Power output for single cell phone (dBm)
Uplink
Downlink
Noise Figure (typical downlink/uplink)
Isolation
Power Requirements
700 A MHz
700 V MHz
800 MHz
1900 MHz
1700/2100 MHz
29.1
23.7
28.4
23.7
29.1
22.7
29.1
22.8
27.1
22.8
5 dB nominal
> 90 dB
110-240 V AC, 50-60 Hz, 20 W
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory
reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of
authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is
too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turns the power off on that band. For a
detected oscillation, after a minimum of 1 minute, the Signal Booster will automatically resume normal operation. After 4 (four) such automatic restarts,
any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal
Booster. Noise power, gain, and linearity are maintained by the Signal Boosters microprocessor, that determines necessary attenuation.
Wilson Electronics, LLC
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www.twitter.com/WilsonCellular
www.facebook.com/WilsonCellular
111239_Rev01_07.30.13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement